Академический Документы
Профессиональный Документы
Культура Документы
Get Started
Solutions Support Training Community Developer Partner
About
Community / Blogs
Change in DLV status in
Production/Process order with
Different Quantities
February 18, 2014 | 341 Views |
Krishnendu Das
more by this author
MAN Production Planning (PP)
Manufacturing
share
0 share
0 tweet share
0
Follow
Whether for a production/process order has been delivered with
partial/full qty can be identified by DLV status. If the delivery happens
partially then the PDLV will be activated.
It is not always that when the total order qty is confirmed then only the
DLV will be activated. This depends on under delivery and over delivery
tolerance also. As well it depends on CNF status.
https://blogs.sap.com/2014/02/18/changeindlvstatusinproductionprocessorderwithdifferentquantities/ 1/10
2/14/2017 Change in DLV status in Production/Process order with Different Quantities | SAP Blogs
Scenario:
Case1:
Created one production order with qty 11 nos. There is no delivery
tolerance.
Now confirmed 5 nos in the order and it is a partial confirmation.
The status of the order is PCNF and PDLV.
https://blogs.sap.com/2014/02/18/changeindlvstatusinproductionprocessorderwithdifferentquantities/ 2/10
2/14/2017 Change in DLV status in Production/Process order with Different Quantities | SAP Blogs
Now we are going for final confirmation.
The order status is DLV and the indicator is set
So the DLV status will be updated if the header status is CNF. Might be
confirmed qty is not same with the order qty (less than the ord qty).
Case2:
https://blogs.sap.com/2014/02/18/changeindlvstatusinproductionprocessorderwithdifferentquantities/ 3/10
2/14/2017 Change in DLV status in Production/Process order with Different Quantities | SAP Blogs
Created another order where delivery tolerance is 0.
Confirmed entire qty (i.e. 4 nos) with partial confirmation.
Though the confirmation is PCNF (for partial confirmation) as all the qty
got delivered equal to the order qty, system makes it DLV. But PCNF
stays because you can confirm more component. This option is given by
SAP to cope up with scrap.
Case3:
Created another order with 8 qty and under delivery tolerance as 50%.
https://blogs.sap.com/2014/02/18/changeindlvstatusinproductionprocessorderwithdifferentquantities/ 4/10
2/14/2017 Change in DLV status in Production/Process order with Different Quantities | SAP Blogs
Now confirmed 4 nos and with partial confirmation.
https://blogs.sap.com/2014/02/18/changeindlvstatusinproductionprocessorderwithdifferentquantities/ 5/10
2/14/2017 Change in DLV status in Production/Process order with Different Quantities | SAP Blogs
Now the order status is DLV. This is because system considers the under
delivery tolerance and make DLV though the confirmation is PCNF (as
total qty is 8 and under delivery is 50%. So DLV will set at 50% of 8 =4
nos) .
Case4:
Created another order with over delivery tolerance as 50%.
https://blogs.sap.com/2014/02/18/changeindlvstatusinproductionprocessorderwithdifferentquantities/ 6/10
2/14/2017 Change in DLV status in Production/Process order with Different Quantities | SAP Blogs
Now confirming 8 nos with partial confirmation. Here system sets the
status as DLV. As over delivery indicator is there, more delivery is
allowed.
https://blogs.sap.com/2014/02/18/changeindlvstatusinproductionprocessorderwithdifferentquantities/ 7/10
2/14/2017 Change in DLV status in Production/Process order with Different Quantities | SAP Blogs
Hope this will clear when and with what situation DLV indicator will be set.
Seen some thread regarding DLV indicator set and tried to explain in this
document.
Will wait for any comment/suggestion .
Regards,
Krishnendu.
Alert Moderator
https://blogs.sap.com/2014/02/18/changeindlvstatusinproductionprocessorderwithdifferentquantities/ 8/10
2/14/2017 Change in DLV status in Production/Process order with Different Quantities | SAP Blogs
5 Comments
You must be Logged on to comment or reply to a post.
MANIKUMAR GK
February 20, 2014 at 6:54 am
Good document for beginners to understand the difference between CNF and
DLV. I appreciate the effort by Krishnendu das
–GK Manikumar
Prasanna Mahendran
December 30, 2014 at 5:37 am
Hi Krishnendu
Its a good document which explains the significance of tolerance fields with
respect to the order quantity and how it impacts order status,really helpful.
ChennakeshavaRao Chinnam
January 8, 2015 at 5:04 am
Hi Krishnendu
Very helpful documents.
Ryan Sutton
January 14, 2016 at 3:32 pm
Hi Krishnendu
https://blogs.sap.com/2014/02/18/changeindlvstatusinproductionprocessorderwithdifferentquantities/ 9/10
2/14/2017 Change in DLV status in Production/Process order with Different Quantities | SAP Blogs
Very helpful
thank you much appreciated.
Srujan Shukla
July 20, 2016 at 3:20 pm
Hi Krishnendu,
Very good document and it is helpful.
Thank you
Srujan Shukla
https://blogs.sap.com/2014/02/18/changeindlvstatusinproductionprocessorderwithdifferentquantities/ 10/10