Академический Документы
Профессиональный Документы
Культура Документы
P-
S646 140 PDS 01 0 1/3
2/4
TECHNIP KT INDIA 001A/B
PDS FOR
GAS OIL FEED PUMP
(TAG NO: 140-P-001A/B)
FLUID HANDLED
Operating case End Of Run
Fluid circulated Gas Oil (1)
Corrosive/erosive agents Organic Sulfur (2)
Pumping temperature °C 63
Viscosity (PT) cP 2.0
Vapor pressure (PT) bar abs 2.5 (3)
Density (60°F/15°C) kg/m3 884.1
Density (PT) kg/m3 853.8
OPERATING CONDITIONS
Normal flow m3/h 140.7 (6)
Design flow m3/h 154.8 (6)
Suction pressure bar g 1.5
Discharge pressure bar g 103.7
Differential pressure bar 102.2
Differential head m 1221
NPSH available m 6.0
Design hydraulic power kW 440
PUMP
Number and type Centrifugal / 1 Operating + 1 Spare
Assumed efficiency 0.66
Design shaft power (estimated) kW 667
Material (Casing / Trim) Carbon Steel / 12 Cr ( Note-9)
DRIVER
Type operating Electrical
spare Electrical
Rated power (Motor rating) kW 735
NOTES
General note : Design conditions result from normal operation conditions. The results obtained with these conditions are
adequate for SOR & EOR conditions.
(1) Gas oil feed is a blend of SRHD, LVGO, LCGO, and LCO.
(2) Organic Sulfur content for the blended feed is 2.73 wt%.
(3) Vapor pressure is based on dissolved gas at the feed drum operating pressure of 1.5 barg. The true vapor
pressure for the pumped liquid is 0.01 bara.
(4) The pump shut-off pressure shall not exceed 127 barg.
(5) Deleted.
(6) Indicated flow rates are process requirements excluding any minimum flow. The design flowrate is 110%
of the normal flowrate.
(7) Pump motor to be designed to handle cold diesel during start-up (catalyst pre-wetting) at 100% of the
above normal flowrate. Start up Diesel density = 861 Kg/m3
This document contains confidential proprietary material belonging to Axens North America, Inc. which may only
be made available to personnel or organizations who have signed appropriate secrecy agreements
PROCESS DATA SHEET
Project N° - Unit Doc. type Equipment N° Serial N° Rev. index
CK-140-PR-30-0039
CLIENT NOCL Rev. Date Made by Checked by Page
PMC CB&I LUMMUS 0 1-Jun-09 AKG NHB
Revision
2 Additional Notes :
th
3 (8) Pumps shall conform to API 610, 10 Edition.
4 (9) Material of construction: S-6
5 (10) Corrosion allowance for casing : 3 mm
6 (11) Mechanical seal shall be dual unpressurised type. Mechanical seal plans: 11, 52.
7 (12) Coupling shall be as per API 671. Coupling shall be flexible type with non-sparking coupling guard
8 (13) Refer P&ID No. CS-140-PR-0002.
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
\\Kt001sf0005\s646\Process\5.0 Coded Document\PDS\3.0 PUMP\140-P-001A,B\Rev_B\[S646-140-PDS-P001-Notes.xls]Notes PD017A12
Property of Technip KT India Ltd. To be returned upon request and used only in reference to contract or proposals of this company.
Reproduction of this print or unauthorised use of patented or patentable features disclosed hereon is prohibited.