Академический Документы
Профессиональный Документы
Культура Документы
in
Set No. 1
Code No: R41037 R10
IV B.Tech I Semester Supplementary Examinations, Feb/Mar - 2015
AUTOMOBILE ENGINEERING
(Mechanical Engineering)
ld
Time: 3 hours Max. Marks: 75
Answer any FIVE Questions
All Questions carry equal marks
*****
or
1 a) What is crank case ventilation and explain how it is achieved in an automobile
engine? [7]
b) Explain the working principle of i) solenoid switch;
ii) Engine Temperature Indicator? [8]
constructional features?
W
2 a) Draw cross section of an automobile tyre and show on it various
b) Explain the differences between fluid fly wheel and torque converter?
3 a) Describe in detail a recirculating ball steering gear with the help of a neat
sketch?
[9]
[6]
[8]
b) Explain in detail the Steering linkage for vehicle with independent front
TU
suspension? [7]
4 a) Explain in detail the construction and working of Girling Mechanical Brake? [9]
b) How do shock absorbers affect spring sag? [6]
system? [8]
b) Discuss the troubles commonly encountered in lighting system of an
automobile? Suggest also suitable remedies? [7]
6 Describe the cooling and lubricating systems used in automobile engines? [15]
7 a) During what engine operating conditions are carbon monoxide and nitrogen
oxide produced most in the exhaust? [7]
ll
b) Discuss in detail various changes in the fuel supply system of engines for
controlling emissions? [8]
A
8 a) How are the ovality and the taper of a cylinder bore checked? [6]
b) Discuss the procedure for repair in case the cylinder wear is found to be more
than permissible limits? [9]
1 of 1
|''|''|||''|'''|||'|
JNTU World
Downloaded From www.alljntuworld.in
Set No. 2
Code No: R41037 R10
IV B.Tech I Semester Supplementary Examinations, Feb/Mar - 2015
AUTOMOBILE ENGINEERING
(Mechanical Engineering)
ld
Time: 3 hours Max. Marks: 75
Answer any FIVE Questions
All Questions carry equal marks
*****
1 a) With the help of a neat sketch explain Splash Lubrication system? Also
or
discuss its advantages and disadvantages? [9]
b) Explain briefly about i) Torsion Bar; ii) Nitriding of crank shaft? [6]
W
3 a) With the help of a neat sketch explain the working of Rack and Pinion
steering gear?
b) A car using rack and pinion type steering gear has steering wheel of 300 mm
diameter and pinion with 5 teeth and 10 mm pitch. Determine the effort
required by each hand at the steering wheel to overcome a load of 600N at the
[8]
rack? [7]
TU
5 a) Discuss the requirements of automotive head lights and explain how they have
JN
7 a) How does an electric assist type of choke help decrease the emission of the
pollutants? [6]
ll
1 of 1
|''|''|||''|'''|||'|
JNTU World
Downloaded From www.alljntuworld.in
Set No. 3
Code No: R41037 R10
IV B.Tech I Semester Supplementary Examinations, Feb/Mar - 2015
AUTOMOBILE ENGINEERING
(Mechanical Engineering)
ld
Time: 3 hours Max. Marks: 75
Answer any FIVE Questions
All Questions carry equal marks
*****
1 a) With the help of a neat sketch explain Pressure Lubrication system? Also
or
discuss its advantages and disadvantages? [9]
b) Write short notes on i) Reboring; ii) Decarbonisation? [6]
steering gear? W
b) Explain the actions of a clutch during engagement and disengagement?
3 a) With the help of a neat sketch explain the working of worm and wheel
b) Explain in detail the Steering linkage for vehicle with rigid axle front
suspension?
[6]
[8]
[7]
TU
4 a) With the aid of a diagram explain the function of the main parts of the master
cylinder? [7]
b) Explain the advantages and disadvantages of independent suspension system
comparing with conventional rigid axle suspension? [8]
6 How does a seat belt enhance safety? Describe clearly the constructional
features and working details of a safety belt? [15]
7 a) Describe how the fuel-air ratio affect the exhaust emission at idle condition of
an automobile? [7]
b) Explain the constructional details and working of a Catalytic converter? [8]
ll
8 a) In case of a cylinder block brought for servicing, it is found that the same had
been rebored already a number of times and so it was no longer possible to
rebore it further. What is the remedy? [6]
A
1 of 1
|''|''|||''|'''|||'|
JNTU World
Downloaded From www.alljntuworld.in
Set No. 4
Code No: R41037 R10
IV B.Tech I Semester Supplementary Examinations, Feb/Mar - 2015
AUTOMOBILE ENGINEERING
(Mechanical Engineering)
ld
Time: 3 hours Max. Marks: 75
Answer any FIVE Questions
All Questions carry equal marks
*****
1 a) Write short notes on Turbo charging and Super charging? [6]
or
b) Explain briefly about i) Anti-Lock Braking system;
ii) Constructional features of automobile clutch? [9]
W
Compare the same with the wire type wheel?
[8]
TU
550 to the rear center line? [7]
6 What type of oil pressure gauges are used in the lubricating system of engine?
Explain each of these gauges with the help of suitable diagrams? [15]
8 a) What will happen if the abrasive particles during servicing operation enter the
A
oil holes and the engine is assembled without removing them? [6]
b) How do you measure the amount of wear in case of connecting rod big end
bearings? Discuss various methods? [9]
1 of 1
|''|''|||''|'''|||'|
JNTU World