Академический Документы
Профессиональный Документы
Культура Документы
AIR CONDITIONERS
The unit displayed is for representational purposes only. Actual unit may vary.
Dear customer
G. Sundar
Chief Executive Officer
IMPORTANT :
Please read this owner’s manual carefully and thoroughly
before installing and operating your room air conditioners.
Please retain this owner’s manual for future reference after
reading it thoroughly.
CONTENTS
Salient Features 1
Inside Overview Speed cool 2
Inside Overview Moving Display 3
Indoor Unit Display Speed cool 4
Indoor Unit Display Moving Display 5
Remote Overview 6
Operations 7
General Instructions for Installation 14
Installation Sketch 17
Installation of Model 18
Take care of your Air Conditioner 22
Precautions to be taken 23
Trouble Shooting Chart 25
Installation and Satisfaction Report 27
Warranty Terms & Conditions 29
Preventive Maintenance Service Coupon 31
Warranty Card(Customer Copy) 33
Warranty Card(service Centre Copy) 35
SALIENT FEATURES
1
INSIDE OVERVIEW INSIDE OVERVIEW
SPEEDCOOL MOVING DISPLAY
Deflector Deflector
Display Conditioned Air out Display Conditioned Air out
Air in Air in
Connection Connection
pipe and pipe and
connecting wire connecting wire
2 3
INDOOR UNIT DISPLAY INDOOR UNIT DISPLAY
SPEEDCOOL MOVING DISPLAY
i-cool
4 5
REMOTE OVERVIEW OPERATIONS
3. Press the "FAN” Button to set the Fan Speed. Each press changes the fan speed
i-Cool CONTROL
from Low-Med.- High-Auto Fan speed. The selected fan setting symbol can be
MANUAL
i-cool seen on the LCD.
4. The Set Temp. is displayed on LCD, Press button to increase and to the
2. The remote signal can be reached upto six metres from the indoor unit. The two digit display shows the set temp. on LCD.
3. When the button is pressed on remote, indoor unit will beep once, indicating O
The setting temp. range is from 16- 31 C.
the receipt of signal. If no beep sound is heard, press the button once again.
Your split AC operates in one of four modes, AUTO-COOL-DRY-FAN. The modes button
4. Remove batteries if remote control has not been used for long time. cyclically chooses between these operating modes.
5. Heat mode is not available with all models.
6 7
OPERATIONS OPERATIONS
8 9
OPERATIONS OPERATIONS
Turbo MODE:
Pressing Turbo key on remote activates the Turbo function and air conditioner goes to BIO-SLEEP MODE: 123
powerful cooling. During this Mode temperature and fan speed cannot be changed.
In this mode the AC works on a preset temperature of 18 degree centigrade at high fan 3 Stage Bio-Sleep with 4 personal preference modes,
speed. Compressor will start immediately in this mode and will continue to operate till set 3 Stage Bio-Sleep works only when air conditioner is in cooling or dry mode,
temperature is achieved .Thereafter it will work in cyclical ON/OFF mode to keep the room
Cools at Set Temp + 2ºC after 2 Cools at Set Temp + 2ºC after 2
Cools at Set Temp + 2ºC after 2 Cools at Set Temp + 2ºC after 2
Cools at Set Temp + 3ºC after Cools at Set Temp + 3ºC after
temperature within 2 degree of set temperature. Press again to cancel this operation. The unit
Wake Up stage
Pressing Money Saved key on remote money saved in Rupees will be displayed on the unit
display. This is a real time savings which is based on actual AC run time .The power tariff
3 Hours
Stage 3
hours
hours
assumed for this is Rs 5.5 per KWHr (1 unit of electricity ) . In case of tariff more then this
hrs
hrs
hrs
assumed rate the actual savings in Rupees will be more than displayed.
next 5 hours
next 6 hours
next 4 hours
next 5 hours
and tariff w.r.t. Non Star AC.
3 Hours
Stage 2
hours
hours
Energy Saver MODE:
Pressing Energy Saver key on remote activates Energy Saver function to keep room normal
next 2 hours.
next 3 hours.
next 2 hours.
next 3 hours.
next 2 hours.
next 3 hours.
next 2 hours.
In this mode temperature cannot be changed & Fan speed can be changed.
Stage 1
Press again to cancel this operation. The unit will run in COOL Mode.
Ceiling Fan Manual Operation – only when optional i-cool ceiling fan
Set Temperature -
controller is installed:
Temperature Set
31ºC - 16ºC
23ºC - 16ºC
24ºC - 27ºC
28ºC - 31ºC
23ºC - 16ºC
24ºC - 27ºC
28ºC - 31ºC
23ºC - 16ºC
24ºC - 27ºC
28ºC - 31ºC
Ceiling fan speed can be controlled only through AC remote control as all other manual
controllers are bypassed while installing i-cool fan controller. Condition
When AC is in any mode other then i-cool mode, Ceiling fan speed can be controlled using
remote control. To enable this Ceiling fan mains have to be in ON position. Press C.F. ON key Bio Sleep -Personal
Preference mode 2
Preference mode 3
Bio Sleep Personal
Preference modes
on remote to start ceiling fan. Ceiling fan speeds can be changed by pressing C.F. + key on Preference mode
remote to increase and C.F . key on remote to decrease. The speeds can be varied by 5 Normal
steps by pressing C.F. + and C.F. keys on remote. Press C.F. OFF key on remote to switch
off ceiling fan. ( symbol will appear on remote control display).
10 11
OPERATIONS OPERATIONS
TIMER Operation:
You can program your split AC to switch itself ON or OFF at particular time. Air Flow direction Adjustment:
Maximum set time is 24 hrs, with 1.0 hr increment . Your split AC has oscillating louvers for uniform cooling around your room.
ON TIMER:
You can stop the oscillation if you so desire.
When the AC is "OFF" (in standby), press "TIMER-ON/OFF" Button on remote to use this feature Up/Down Air Direction Adjustment:
as the TIMER. (make sure that MCB switch is "ON". The "TIMER-ON/OFF" light on Indoor unit will 1. 5 step air swing can be achieved for the one time Press SWING
glow ON. button on remote, the Up/Down air louvers will move to the
For EXAMPLE: specific angle.
Suppose you want to switch ON the AC after 8 hrs. Press "TIMER-ON/OFF" button, when AC is You can set 5 different angle settings, to set Up/Down louvers in
in OFF condition. Press same " " button 8 times to set 8 hrs time delay. order of (1) (2) (3) (4) (5)
Press "TIMER-ON/OFF" button to set on timer. Display on Remote will show "8”. 2. For the next Press SWING button to start Up/Down Air Louver which
OFF TIMER: starts swinging automatically.
When the AC is "ON", press "TIMER-ON/OFF" Button on remote to use this feature as Press again the SWING button to stop swinging at desired
the TIMER. The "TIMER-ON/OFF" light on Indoor unit will glow ON. position.
For EXAMPLE:
Suppose you want to switch OFF the AC after 8 hrs. Press "TIMER-ON/OFF" button, when AC is Left/Right Air Direction Adjustment:
in ON condition. Press same button 8 times to set 8 hrs time delay . Move manually, the left right air
louver at desired position as shown
Press "TIMER-ON/OFF" button to set OFF timer. Display on Remote will show "8”.
in following figure.
CANCEL TIMER:
If you want to cancel the Timer either TIMER ON or TIMER OFF, press the corresponding
TIMER-ON/OFF button and set the time to 0:0. Emergency Operation Switch:
CLOCK SET: In case the batteries in the remote are worn out, or remote is faulty or misseing, use
As long as remote controller is power on, the clock will run and it can be adjusted in any emergency operation switch (*) to ON/OFF AC.
condition even when the air conditioner is off. While the remote is electrified for the Every time the switch is pressed, it changes in sequence of COOL Ý STOP.
first time, the time is 0:00, means the clock counts the time automatically. O
In Emergency operation mode the set temperature will be 24 C, Fan speed will be
To adjust the clock press theTIMER ON/OFF button for 10 seconds, high and Up/Down Air louvers are in swinging mode.
the time of hour flashes, during this period add the time of hours by pressing the button To access emergency switch, open the grill as
and reduce the time by pressing the button .After setting the time of hour , press the shown in the figure.
button TIMER ON/OFF again to adjust the time of minute(Do not need to press for
10seconds.)When the time of minutes flashes, press the button to add time of minute,and
press the button to reduce it.Finish setting of minute,press the button TIMER ON/OFF for
the third time to confirm the clock.
12 13
GENERAL INSTRUCTIONS FOR GENERAL INSTRUCTIONS FOR
INSTALLATION INSTALLATION
Locating the indoor and outdoor units Locating the Outdoor Unit
properly will help optimise the performance of The outdoor unit houses the compressor,
your airconditioner. While your Onida / condenser fan and electrical components.
Dealer's Technician will be happy to guide you The heat removed from the room is expelled
on the best location for your airconditioner,
to the atmosphere through the outdoor unit.
here are a few helpful hints.
Once again, the Onida / dealer's Technician
will ensure optimal installation of the ODU for
Locating the Indoor Unit
you. However, the following information will
Locate the IDU for the best cool air be of interest to you.
circulation. Preferably, there should be
no obstructions nearby, as shown in the The Outdoor Unit can be mounted on a
adjacent figure. wall, sunshade or skirting.
All indoor units will form condensate water. Ensure that air can pass freely through
Please ensure that the condensate can the unit. Please allow at least 2 meters
be drained out of the room to a toilet / free space on the air outlet side, and 0.3
pantry, etc. The installation engineer will meters on the air inlet side.
make sure that a "U" bend is provided in
the drain to prevent insects from coming
into the room through the drain tube, as
shown in the adjacent figure.
If more than one ODU is to be installed,
they must be properly separated, so that
the warm air from the outlet of one does
not enter the inlet of the other.
14 15
GENERAL INSTRUCTIONS FOR
INSTALLATION INSTALLATION SKETCH
7 Felt 1
frame or support. If mounted on a 8 Adiabatic Underlay 1
H F
wall, please ensure that the wall is 9 Connecting Cable 1
thick enough and that the frame is Drain Joint(supplied by remark
10 customer)
supported adequately. C
11 Clamping cover of pipe 1
250cm ab
ove
B
60cm above
provided for the service engineer to F Opening cap 1
service the unit. It is a good idea to e
G W all -hole cover 1
v
abo
provide a catwalk (a platform) 30c
30c
m
H Indoor wall-hole cover 1
mab
ove I Putty 1
around the unit and access door / To
OD J Air proof oil remark
window to the Unit. U U
OD Air Outlet Shockproof rubber
To 9 K cushion(supplied by 1
E
customer)
Electrical outlet e
MCB 200
cma
bov
A 60c
ma
bov
After the location of the outdoor unit and STABILISER
e
16 17
INSTALLATION INSTALLATION
n Connecting of cables
n INDOOR UNIT
1. Open the front panel
1. Fitment of mounting plate Electrical box cover
2. Dismentle the electric box cover
The mounting plate should be fitted on the structural part of wall on which indoor unit Indoor unit
and fastener terminal Screw
is to be installed.
3. Connect the cable
2. Drill two holes at a distance of 450 mm between them for the expansion bolts.
4. Reassemble the fastener and electric
fasten string at the central hole at least B from top Diagram
box cover. Fastener
A or more C or more Screw
Pull the Connecting cable’s
from sidewall from sidewall wire in completely
Connecting cable
plumb
mounting
plate
Insert Ruler Center of Hole( ) The connecting cables must be clipped together.
Align Ruler with straight line
Special cable to be used to connect indoor unit and outdoor unit.
The electric box cover must be mounted on its position on outdoor unit.
18 19
INSTALLATION INSTALLATION
n Connecting of pipes
n Sealing the wall hole and clamping the pipe Gas pipe
Gas charging hole
Use putty to seal the wall hole. Bottle s valve of storage refrigerant
Use pipe fastener to clamp the pipe on wall Bottle of storage refrigerant
External connection
electric wire
Gas side piping
Fixing Hook
Liquid side piping n Test
Mounting Board
Gas side
Proceed leak test (with leak detector or soap water.) and inspect connecting
piping insulation Liquid side cables before test operation.
piping insulation
Mounting Board air proof with putty Test procedure: (Control by emergency operation switch or remote
Water
Finally wrap it
with tape
drainage controller) For detailed operation, see OPERATION OF AIR CONDITIONER
pipe
in the manual.
20 21
TAKE CARE OF YOUR
PRECAUTIONS TO BE TAKEN
AIR CONDITIONER
The filters will be visible Don't use hot water to clean your front grill
Don't use scouring powder, harsh soaps, wax or polish on the grill.
Lift the filters slightly upwards Don't switch on the air conditioner immediately after switching it off.
Wait for 2 minutes.
Don't operate with a clogged filter
Don't block air intake & outlet vents
Pull out the filters
Don't change setting unnecessarily.
22 23
TROUBLE SHOOTING CHART
Units does not cool The airflow paths are Remove all
(Even after the normal not free obstructions to make
Time Delay of approx. the airflow paths free
2/3 minutes for
compressor to start)
Note: If the unit still does not work, or if any other types of symptoms are encountered,
shut off the mains (switch fuse unit) and call the service engineer.
24 25
INSTALLATION & SATISFACTION
REPORT
Customer Name :
Address
Phone[O] [R]
26 27
WARRANTY TERMS
AND CONDITIONS
M/S. MIRC ELECTRONICS LTD, WARRANTS THIS ONIDA AIR CONDITIONER[(except the front grill,
knobs, remote unit and add-on plastic parts) TO THE ORIGINAL PURCHASER TO BE FREE FROM
DEFECTS IN MATERIALS AND WORKMANSHIP WITHIN ONE YEAR FROM THE DATE OF PURCHASE
AS PROVIDED IN THE WARRANTY REGISTERATION CARD.
28 29
Preventive Maintenance Service
Customer Identification
8. It shall be the absolute discretion of the company to a) effect the repairs or replacement of parts Number:
whether at the site of installation or at any service centre, and b) have the job attended to either by the Preventive Maintenance Service 1 Date: ________
Company's service personnel or its authorised dealer ______________________
Customer Identification Number: ___________________________________________
9. This warranty is in the nature of and for the purpose of set forth herein above and in particular the
Unit Model: ___________ Name of the customer:
Company shall not in any event be liable for direct, indirect, incidental or consequential loss or
damages to either the said purchaser and /or his property or any other third party. ____________________________________________________
Sr. No: _______________
10. The AC is designed to operate at a range (230V +/- 10%). Any failure due to operation of the machine Installation address: ______________________________________________________
beyond these limits will not be covered by the above warranty. Name of Serviceman: _______________________________________________________________________
Customer shall ensure that a stabilizer is installed in those areas where voltage is not available within _
______________________
the warranty range (230V +/- 10%). The stabilizer should be of any reputed manufacturer, tested and _______________________________________________________________________
recommended by the Company. Date: ______ Time: _____ _
11. The purchaser should preserve the original invoice for necessary verification and produce, as and Phone: _________________ Mobile: __________________ Fax: ________________
when required.
E-mail: _________________________________________________________________
12. Warranty null and void if: Sign. of Serviceman Unit model: ____________________________ Serial Number: __________________
i. The Air Conditioner is not purchased from the authorized dealers of the company.
Service report number: ___________________________________________________
ii. The Service Centre copy of warranty card is not received within 10days of date of purchase at the
nearest Authorised Service Centre.
Customer's Signature: _______________________ Name:
iii. Any damage is caused by accident, mishandling, tampering with installation, or negligence in
following instructions of the user manual issued by Company.
iv. Any damage is caused by improper electrical circuit outside the unit or by any defective electrical
supply Preventive Maintenance Service
Customer Identification
v. At any time, during the warranty period if any part of the unit is tampered with, altered, repaired or Number:
serviced by any unauthorized person, not being the authorized representative of the company or Preventive Maintenance Service 2 Date: ________
its authorized dealers ______________________
Customer Identification Number: ___________________________________________
vi. The serail number of the unit or any part thereof is damaged , defaced, altered, obliterated , or
Unit Model: ___________ Name of the customer:
tampered with or removal for any reason whatsoever
____________________________________________________
viii. The unit is unauthorisedly moved from its original place of installation or re-installation Sr. No: _______________
Installation address: ______________________________________________________
13. None of the employees and /or Authorized Dealers of the Company have any authority whatsoever to
Name of Serviceman: _______________________________________________________________________
vary the terms and conditions of this warranty.
_
14. This warranty shall be deemed to have been issued at Mumbai, state of Maharashtra and courts at ______________________
Mumbai shall have exclusive jurisdiction on matters covered by or following from this warranty, and _______________________________________________________________________
the original purchaser alone shall have cause of action arising out of the transaction. Date: ______ Time: _____ _
Phone: _________________ Mobile: __________________ Fax: ________________
E-mail: _________________________________________________________________
Sign. of Serviceman Unit model: ____________________________ Serial Number: __________________
Service report number: ___________________________________________________
30 31
MIRC Electronics Limited
Serial No. Warranty Card
Customer Copy
Customer Details
Residence Address:
Dist: Pin:
State: Occupation:
Product Details
Please Tick The Appropriate Product Colour TV B&W TV DVD Washing M/C. AC Plasma TV Rear Projection TV
Purchase Date
Day Month Year
Signature
Bill No.
Thank you for selecting a World Class product and we assure you that it will perform as per your expectations
We thank you for taking your time to complete this form. All Information Provided by You will be Kept Confidential.
(Please Fill In, Tear off, Fold and Mail this form to Reach us within 10 days of the Product Purchase.)
We welcome your Valuable Suggestions, if any, to Improve our Products and Services :
Customer Code:
Branch:
Residence Address:
Dist: Pin:
State: Occupation:
Product Details
Please Tick The Appropriate Product Colour TV B&W TV DVD Washing M/C. AC Plasma TV Rear Projection TV
Purchase Date
Day Month Year
Signature
Bill No.
Thank you for selecting a World Class product and we assure you that it will perform as per your expectations
We thank you for taking your time to complete this form. All Information Provided by You will be Kept Confidential.
(Please Fill In, Tear off, Fold and Mail this form to Reach us within 10 days of the Product Purchase.)
We welcome your Valuable Suggestions, if any, to Improve our Products and Services :
Customer Code:
Branch: