Академический Документы
Профессиональный Документы
Культура Документы
To Order by Telephone
Call Videojet at 1-800-843-3610 and speak to one our Customer Service
Representatives. Telephone hours are 7:00 a.m. to 7:00 p.m., Monday
through Friday (Central Standard or Daylight Time). In emergencies,
please contact our 24-hour Technical Assistance Department at the same
telephone number.
To Order by Fax
Fax orders can be sent 24 hours a day, 7 days a week:
• 1-800-582-1343 (USA)
• 630-616-3629 (Int’l)
Rev AD 10-1
Videojet 1310 Service Manual
Ink System
Ink Compartment
Figure 10-1 shows the ink compartment.
2
3
4
10
5
7
6
1. Vent Shield
2. Ink Bottle
3. Make-up Bottle
4. Ink Supply Tank
5. Make-up Supply Tank
6. Fluid Management System (FMS)
7. Pressure Transducer
8. Main Ink Filter
9. Vacuum Pump
10. Printhead
4
5
Table 10-1 lists the parts of the ink reservoir top assembly.
Note: 1. This part is available only in the O-ring Kit on page 10-20.
Note: 2. This part is available in the Miscellaneous Hardware Kit on page 10-57.
Valve, 3-way
Figure 10-3 shows the 3-way valve.
Table 10-3 lists the part number of the valve, 2-way, 90° cabinet.
Table 10-4 lists the part number of the valve, 2-way, 180° printhead.
2
2
Table 10-5 lists the part number of the check valve, nozzle wash assembly.
Tube Coupling
Figure 10-7 shows the tube coupling.
1.O-ring
2. Transducer Clip
3. Main Ink Filter Assembly
Table 10-7 lists the parts of the main ink filter assembly.
Note: This part is available only in the O-ring Kit on page 10-20.
1
2
3
1. Nut 3. Spring Compression
2. Piston 4. Rolling Diaphragm
Table 10-8 lists the parts of the flush pump rebuild kit.
7
2
2 — Manifold, Pump 1
3 — Fitting, Tube, Ferrule, 2
Back, 1/8 T
4 — Fitting, Tube, Nut, 1/8 2
Tube
5 — Tubing, Teflon 0.032 ID x 1
0.047W
6 — Fitting, Tube, Ferrule, 2
Front, 1/8
7 — Washer, Flat 0.125 ID 2
Table 10-10: Pump Manifold Assembly - Parts List
Note: This part is available only in the O-ring Kit on page 10-20.
2
1
Table 10-11 lists the parts of the cap and stem reservoir assembly.
Transducer, Pressure
Figure 10-12 shows the pressure transducer.
1 2
1. Pressure Transducer
2. O-ring
— Clip, Retaining 1
Table 10-12: Pressure Transducer Parts List
Note: This part is available only in the O-ring Kit on page 10-20.
1 2
10 7 8
Table 10-14 lists the part number of the tee fitting, 1/16.
Table 10-16 lists the part number of the fitting compression, 1/8” tubing,
10 each.
Table 10-18 lists the part number of the fitting, 1/8”x27 tee branch 10 each.
Table 10-19 lists the part number of the fitting, 1/8”male elbow.
Ink Pump
Figure 10-18 shows the ink pump assembly.
Table 10-20 lists the part numbers of the ink pump assembly.
Note: This part is available only in the O-ring Kit on page 10-20.
O-ring Kit
Table 10-21 lists the parts of the O-ring kit.
Check Valve
Figure 10-19 shows the check valve.
Gauge, vacuum/pressure
Figure 10-20 shows the vacuum/pressure gauge.
Table 10-24 lists the part number of the ink and make-up reservoir.
Table 10-25 lists the part number of the ink and make-up reservoir filter.
Table 10-26 lists the part number of the float assembly reservoir.
1
7
6 2
3
5
Table 10-27 lists the parts of the washer pump cap assembly.
Note: This part is available in the Miscellaneous Hardware Kit on page 10-57.
Table 10-28 lists the part number of the vacuum pump assembly.
Table 10-29 lists the part number of the rotary mechanism ink.
Note: This part is available in the Miscellaneous Hardware Kit on page 10-57.
Table 10-30 lists the part number of the rotary mechanism make-up.
Note: This part is available in the Miscellaneous Hardware Kit on page 10-57.
Table 10-31 lists the part number of the plug reservoir assembly.
Electronics Compartment
Figure 10-30 shows the electronics compartment.
1
8
2
3
7
4
6
Fan Filter
Figure 10-30 shows the fan filter.
Fan Assembly
Figure 10-31 shows the fan assembly.
3
4
1. Bracket Fan Assembly
2. Fan Assembly with Connector
3. Guard, Fan 120 mm
4. Nut, Keps, M4
Note: This part is available in the Miscellaneous Hardware Kit on page 10-57.
Note: This part is available in the Miscellaneous Hardware Kit on page 10-57.
Table 10-38 lists the part number of the packaged bulkhead board kit.
Note: This part is available in the Miscellaneous Hardware Kit on page 10-57.
1. Display LCD
2. Spacer LCD
3. Nut, hex, Keps, M3
Table 10-39 lists the part number of the packaged display assembly.
1. AC Shield
2. Power Supply
3. Nut, Hex, Keps, External, M3
Table 10-40 lists the part number of the packaged power supply kit.
Controller Board
Table 10-41 lists the part numbers of the controller board.
Wrist strap 1
SP378905-02 Controller board, Service key 1
disabled
Controller PCB 1
Standoff, 6x16.5mm, steel, 4
Zink, hex, male-female
378965 Nut, kept, M4 4
See Note below
Wrist strap 1
Table 10-41: Controller Board Parts List
Note: This part is available in the Miscellaneous Hardware Kit on page 10-57.
Door/Keyboard Assembly
Figure 10-35 shows the door/keyboard assembly.
6 5
4
1
3
2
Note: This part is available in the Miscellaneous Hardware Kit on page 10-57.
Battery, Lithium 3V
Table 10-48 lists the part number of the harness, display 14-pin.
1. Tubing
2. Nozzle Assembly
3. Screw M2.5x4 socket head cap
Table 10-50 lists the part number of the packaged nozzle assembly.
Note: This part is available in the Charge Electrode Screws/Hardware Kit on page
10-59.
Filter, Printhead
Table 10-51 lists the part number of the printhead filter.
Housing 6 position
Table 10-53 lists the part number of the housing 6 position.
Contact snap in
Table 10-55 lists the part number of the contact snap in.
Fitting, Barbed
Table 10-57 lists the part number of the barbed fitting.
Cap HV Connector
Table 10-58 lists the part number of the cap HV connector.
Connector 2-pin
Table 10-59 lists the part number of the connector 2-pin.
3
6
Table 10-60 lists the part number of the packaged heater assembly.
Note: 1. This part is available in the Printhead Large Screws Kit on page 10-58.
Note: 2. This part is available in the Printhead Small Screws Kit on page 10-58.
Table 10-61 lists the part number of the ink return block.
Note: This part is available in the Printhead Small Screws Kit on page 10-58.
Table 10-62 lists the part number of the printhead front cover.
Cradle, Packaged
Figure 10-40 shows the cradle, packaged.
Table 10-64 lists the part number of the printhead rear cover.
Clip, Retainer
Figure 10-42 shows the clip.
Table 10-66 lists the part number of the 24 VDC 2-way valve.
Table 10-68 lists the part number of the high voltage arm and ground plate
assembly.
Table 10-68: High Voltage Arm and Ground Plate Parts List
Note: This part is available in the Printhead Small Screws Kit on page 10-58.
Note: This part is available in the Miscellaneous Hardware Kit on page 10-57.
Tubing Kit
Table 10-70 lists the parts of the Videojet 1310 FMS tubing kit.
— Nuts, kept M4 10
— Screw M4x8 5
— Screw soc, flt hd M4 X 8 5
— Screw, pan M3 x 8 10
Table 10-85: Miscellaneous Hardware Kit - Parts List (Continued)
O-Ring 0.090” ID EP
Table 10-93 shows the part number of O-Ring 0.090” ID EP kit.
5x5 Accud- 1832 10 3.9 916 279.1 .066 - .129 1.7 - 3.3 0 - 250
rop™ Sin-
gle Line
5x7 Single 1570 10 3.9 785 239.2 .110 - .216 2.8 - 5.5 0 - 250
Line (High
Speed)
5x7 Single 784 10 3.9 392 119.4 .118 - .236 3.0 - 6.0 0 - 250
Line (High
Quality)
7x9 Single 633 8 3.1 396 120.7 .141 - .291 3.6 - 7.4 0 - 250
Line (High
Speed)
7x9 Single 457 8 3.1 286 87.1 .133 - .271 3.4 - 6.9 0 - 250
Line (High
Quality)
7x10 Sin- 411 8 3.1 257 78.3 .153 - .279 3.9 - 7.1 0 - 225
gle Line (3)
10x16 Sin- 249 4 1.5 312 95.0 .236 - .393 6.0 - 10.0 0 - 150
gle Line
(High
Speed)
10x16 Sin- 124 4 1.5 156 47.5 .236 - .401 6.0 - 10.2 0 - 150
gle Line
(High Qual-
ity)
16x24 Sin- 80 3 1.1 134 40.8 .236 - .370 6.0 - 9.4 0 - 125
gle Line
(High
Speed)
5x5 Accud- 550 10 3.9 275 83.8 .059 - .118 1.5 - 3.0 0 - 250
rop™ Twin
Line (High
Speed)
5x5 Accud- 366 10 3.9 183 55.7 .059 - .118 1.5 - 3.0 0 - 250
rop™ Twin
Line (High
Quality)
5x7 Twin 392 10 3.9 196 59.7 .078 - .145 2.0 - 3.7 0 - 225
Line
7x9 Twin 228 8 3.1 143 43.5 .114 - .177 2.9 - 4.5 0 - 125
Line
5x5 Accud- 366 10 3.9 183 55.7 .059 - .098 1.5 - 2.5 0 - 150
rop™ Tri
Line (High
Speed)
5x5 Accud- 174 10 3.9 87 26.5 .059 - .098 1.5 - 2.5 0 - 150
rop™ Tri
Line (High
Quality)
5x7 Tri Line 250 10 3.9 125 38.1 .078 - .122 2.0 - 3.1 0 - 125
(High
Speed)
5x7 Tri Line 174 10 3.9 87 26.5 .074 - .106 1.9 - 2.7 0 - 100
(High Qual-
ity)
7x10 Tri 104 8 3.1 65 19.8 .078 - .110 2.0 - 2.8 0 - 125
Line (3)
I S
Safety
Ink
Caution Statements 2
Safety Guidelines 5
Equipment Guidelines 3
Ink drop break-off
Ink Guidelines 5
Theory 2
Introduction 1
Ink Low Icon 6
Medical Emergencies 8
Ink stream
Warning Statements 2
Controlling 6–8
Satellites 8
Electrostatic effects on 3–5
Scheduled Maintenance 13
Pressure effects on 5
Shutdown sequence
Ultrasonic effects on 2
Printhead 40
Inks
Start-up sequence
Medical Emergencies 8
Printer 9
MSDS Usage 6
Rev AD Index-1
Videojet 1310 Service Manual
W
Warning Statements 2
Warnings
Fluid low 51
Index-2 Rev AD