Академический Документы
Профессиональный Документы
Культура Документы
Features/Benefits
• Maximum operating temperature is 550°F
(288°C).
• Maximum operating pressure differential is
normally 15,000 psi (103,35 MPa).
NOTE: Some packer sizes may be restricted to
lower pressure differentials; others may be rated
higher.
• Packing element is chemically inert to hostile
environments (H2S, CO2, inhibitors).
• Unaffected by temperature cycling.
• Metal-to-metal sealing eliminates O-ring seals.
This document is and contains unpublished, copyrighted and confidential information of Baker Hughes, and is revealed for limited purposes only. This document
is the property of Baker Hughes and is to be returned to Baker Hughes on request and may not be reproduced, used or disclosed to persons not having a need to
know consistent with the purpose of the document, without the written consent of Baker Hughes. This document is not rented, loaned or sold, either alone ore in
conjunction with equipment or product. © 9/30/03 Baker Hughes Incorporated.
Unit No. 8277 10-1-03 Models “HE” And “HEA” Retainer Production Packers
Rev. New Page 2 of 15 And Model “B-2” Hydraulic-Set Adapter Size
WARNING
Use of Baker equipment contrary to
manufacturer’s specification may result in
property damage, serious injury or fatality.
Specification Guide
Casing Packer Accessories
ID Range LTSA ATSA
Min Bore
T&C (Nominal) in Packer Dia of Model Model Model Min Bore
Thru
OD Weight Which Model Size Max Sealing “L” “N” “NM” Thru Seal
Packer
Lbs/Ft Packer May OD Bore Assembly
Body Size
Be Run
10.5 - 12.6 3.958 - 4.052 HEA 375-26 x 19 3.750 1.929 - 26.19
4-1/2"
9.5 - 10.5 4.044 - 4.090 HE 381-26 3.812 2.688 40-26 -
23.2 - 24.2 3.958 - 4.052 HEA 375-26 x 19 3.750 1.929 - 26-19
23.2 4.044 - 4.090 381-26 3.812 2.688 1.929
HE 2.688 40-26 -
396-26
5" 18 - 21.4 4.126 - 4.276 3.968
HEA 396-26 x 19 1.929 - 26-19
HE 425-26 2.688 40-26 -
11.5 - 15 4.408 - 4.670 4.250
HEA 425-30 x 22 2.265 3.000 - 30-22 2.265
HE 396-26 2.688 40-26 -
32.3 - 35.3 4.126 - 4.276 3.968
HEA 396-26 x 19 1.929 2.688 - 26-19 1.929
5-1/2"
HE 425-26 2.688 40-26 -
23 - 28.4 4.408 - 4.670 4.250
HEA 425-30 x 22 2.265 - 30-22 2.265
32 - 35 5.540 - 5.720 535-32 5.350
6-5/8"
23.2 - 32 5.660 - 6.004 546-32 5.468 3.000
HE 3.250 80-32 - 2.303
44 - 49.5 5.504 - 5.720 535-32 5.350
7"
35 - 45.4 5.660 - 6.004 546-32 5.468
Assembly milled upset in each Cone Ring must fit into the
split of the corresponding Packer Ring.
“HE” Packers
8. The splits in the Cone Rings (10) should be as-
Sizes 381-26 and 396-26 sembled onto the Cone Upsets which have
1. Secure assembly or components with Lead been previously installed in the cone.
Pads whenever supported by a hand vice. 9. Rotate the Upper Cone (8) until split in the up-
2. Use downhole grease on all straight threads. per Packer Ring (11) is 180° from split in lower
3. Install Adjusting Nut (17), Key (16), and Lower Packer Ring.
Slip (5). Fill cavity in Lower Cone (15) with Shell 10.The linear position of the Lower Cone (15) must
Darina #2 or equivalent and assemble on Body be adjusted so that the Packing Element (14)
(1). System components are as loose as possible
NOTE: The beveled end of the Adjusting Nut (17) but tight enough to prevent the Packer Rings
must not be placed against the Lower Slip (5). (11) and Cone Rings (10) from becoming rota-
4. Adjust the Adjusting Nut (17) until the Lower tionally unlocked from the Lower Cone. Once
Slip (5) is snug. Securely install Brass Shear the Lower Cone is in position, install Brass
Screws (9) in Lower Cone (15) and Hex Socket Shear Screws (9) and securely torque against
Set Screws (18) in Adjusting Nut. the bottom of each milled slot.
5. Lightly grease ID of Packing Element (14) with NOTE: A correctly assembled Element System will
Baker Tubing Seal Grease. have no bulge resulting from axial compression of
the Packing Element (14). Place a straight edge
6. Assemble the following components onto the across Upper Cone (8) and Lower Cone (15). If the
Body (1): Cone Rings (10), Packer Rings (11), Packing Element touches, reject. If the Packing
Wire Mesh Back-Up Rings (12), Element Element clears, accept. The Wire Mesh Back-Up
Washers (13), Packing Element (14), Filler Rings (12) should be able to be rotated by hand. The
Ring (20), O-ring (19), and Upper Cone (8). Packer Rings (11) and Cone Rings (10) should be
7. Splits on adjacent Packer Rings (11) and Cone free to rotate slightly but should stay locked in by the
Rings (10) must be 180° apart. Punched or cone upset and punched upset.
Unit No. 8277 10-1-03 Models “HE” And “HEA” Retainer Production
Rev. New Page 4 of 15 Packers And Model “B-2” Hydraulic-Set Adapter
10.Assemble Upper Slip (5) onto the Body (1). As- 9. Drive Packing Element (14) onto the Body (1)
semble Body Lock Ring (4) onto the Body then with sleeve and large rubber hammer until Seal
screw Support Ring (3) onto Body Lock Ring. Ring (21) is within 1/2 inch of Packer Ring (11).
Screw Top Sub (6) onto the Body and bump Adjust Seal Ring to be 1/32 to 3/16 inch from
tight. Body Lock Ring should appear in the mid- shoulder of Packing Element, then rotate Pack-
dle of the Support Ring inspection hole. Slide ing Element with strap wrench until Seal Ring
(do not rotate) the Support Ring and Body Lock contacts Packer Ring. (Pin in seal should fit in
Ring as a unit against the Upper Slip. A rubber split on Packer Rings.)
mallet may be used to bump the Support Ring 10.Assemble Packer Rings (11) and Cone Rings
down. Rotate the Support Ring down until Up- (10) with split in Packer Ring 180° from adja-
per Slip is able to hand turn with slight drag. cent Packer Ring.
11.Drill through the Support Ring (3) to the diame- 11.Assemble Back-up Ring (22) and Upper Cone
ter and depth specified on the assembly draw- (8) on Body (1). Then securely install Brass
ing and install Drive Pins (2). Shear Screws (9) in the Upper Cone.
12.Fully torque all Brass Shear Screws (9) into 12.Linear position of the Seal Ring (21) must be
place. Apply one drop of 3M adhesive to all adjusted so that the Packing Element (14) com-
screws and drive pins. ponents are tight enough to prevent the Cone
13.File off all wrench marks. Rings (10) and Packer Rings (11) from becom-
Size 425-26 ing rotationally unlocked from the Upper Cone
(8). (A correctly assembled Element System
1. Secure assembly or components with Lead
will have no bulge higher than the cones.)
Pads whenever supported by a hand vice.
13.Assemble Upper Slip (5) onto the Body (1). As-
2. Use downhole grease on all straight threads.
semble Body Lock Ring (4) onto the Body such
3. Install Adjusting Nut (17), Key (16), and Lower that the end of Lock Ring is 1/8 to 1/4 inch from
Slip (5). Fill cavity in Lower Cone (15) with Shell end of Upper Slip. Then screw Support Ring (3)
Darina #2 or equivalent and assemble on body. onto Body Lock Ring until end of Support Ring
NOTE: The beveled end of the Adjusting Nut (17) is even with end of Body Lock Ring. Screw Top
must not be placed against the Lower Slip (5). Sub (6) onto Body and bump tight. Rotate Sup-
4. Adjust the Adjusting Nut (17) until the Lower port Ring down until Upper Slip is able to turn
Slip (5) is snug. Securely install Brass Shear with slight drag. Body Lock Ring should appear
Screws (9) in Lower Cone (15) and Hex Socket in the middle of the Support Ring inspection
Set Screws (18) in Adjusting Nut. hole.
5. Install Back-up Ring (22) to fit flush against the 14.Drill through the Support Ring (3) to the diame-
Lower Cone (15). ter and depth specified on the assembly draw-
6. Assemble Cone Ring (10) and Packer Rings ing and install Drive Pins (2).
(11) on Packer with upset on Cone fitting into 15.Fully torque all Brass Shear Screws (9) into
split on Packer Ring. (Cone Ring must be as- place. Apply one drop of BPPS 026/AD001 to
sembled against Lower Cone (15).) all screws and Drive Pins (2).
7. Heat 90 and 95 hard Packing Element (14) to 16.File off all wrench marks.
170°F. Lightly grease ID of Packing Element Size 568-32
with Baker tubing seal grease. Install Filler Ring
1. Secure assembly or components with Lead
(20) by pushing Filler Ring into Packing Ele-
Pads whenever supported by a hand vice.
ment (by hand) until edge of Filler Ring is even
with groove. With hydraulic pressure push on 2. Use Downhole grease on all straight threads.
high side of ring to snap into groove of Packing 3. Install Adjusting Nut (17), Key (16), and Lower
Element. Install O-ring (19). Slip (5). Fill cavity in Lower Cone (15) with Shell
8. Push Seal Rings (21) into Flange of Packing El- Darina #2 or equivalent and assemble on Body
ement (14) until shouldered. Pins in Seal Ring (1).
must be assembled 180° apart. NOTE: The beveled end of the Adjusting Nut (17)
must not be placed against the Slip (5).
Models “HE” And “HEA” Retainer Production Unit No. 8277 10-1-03
Packers And Model “B-2” Hydraulic-Set Adapter Rev. New Page 5 of 15
4. Adjust the Adjusting Nut (17) until the Lower 3. 1/4 dimple drill x 1/16 deep in Body (1). Install
Slip (5) is snug. Securely install Brass Shear Brass Shear Screws (9).
Screws (9) in Lower Cone (15) and Hex Socket 4. Use downhole grease on all straight threads.
Set Screws (18) in Adjusting Nut.
5. Lightly grease ID of Packing Element (14) with
5. Lightly grease ID of Packing Element (14) with non-petroleum based grease.
Baker Tubing Seal Grease.
6. Secure assembly with lead pads whenever
6. Assemble the following components onto the supported by hand vice.
Body (1): Wire Mesh Back-Up Rings (12), Ele-
7. Torque connections with bucking unit.
ment Washers (13), Packing Element (14), and
Upper Cone (8). 8. Splits in Packer Rings (11) and Cone Rings
(10) should be 180° apart.
7. The linear position of the Lower Cone (15) must
be adjusted so that the Wire Mesh Back-Up 9. Packing Element (14) System should be tightly
Rings (12) are as loose as possible but tight hand snugged in order for Packer Rings (11)
enough to prevent free spinning. Once the Low- and Cone Rings (10) not to be able to hand ro-
er Cone is in position, install Brass Shear tate after inserting Brass Shear Screws (9) into
Screws (9) and securely torque against the bot- Upper Cone (8).
tom of each milled slot. 10.File off wrench marks.
NOTE: A correctly assembled Element System will “HEA” Packers
have no bulge resulting from axial compression of
Size 375-26 x 19
the Packing Element (14). Place a straight edge
across Upper Cone (8) and Lower Cone (15). If 1. Secure assembly or components with Lead
Element touches, reject. If Element clears, accept. Pads whenever supported by a hand vice
The Wire Mesh Back-Up Rings (12) should be able 2. Use downhole grease on all straight threads.
to be rotated by hand.
3. Make up Upper Bore Receptacle (23) to Body
7. Assemble Upper Slip (5) onto the Body (1). As- (1). Use API modified thread dope and torque
semble Body Lock Ring (4) onto the Body then connection in bucking unit to value specified on
screw Support Ring (3) onto Body Lock Ring. the assembly drawing. Attach bucking unit to
Screw Top Sub (6) onto the Body and bump Body at correct position. File off all wrench
tight. Body Lock Ring should appear in the mid- marks.
dle of the Support Ring inspection hole. Slide
4. Drift ID with drift bar specified on assembly
(do not rotate) the Support Ring and Body Lock
drawing.
Ring as a unit against the Upper Slip. A rubber
mallet may be used to bump the Support Ring 5. Temporarily install Body Lock Ring (4) and
down. Rotate the Support Ring down until Up- Support Ring (3) shouldered against the Upper
per Slip is able to hand turn with slight drag. Bore Receptacle (23).
8. Drill through the Support Ring (3) to the diame- 6. Assembly the following components onto the
ter and depth specified on the assembly draw- Body (1): Upper Slip (5), Upper Cone (8), Wire
ing and install Drive Pins (2). Mesh Back-Up Rings (12), Element Washers
(13), Packing Element (14), Filler Ring (20), O-
9. Fully torque all Brass Shear Screws (9) into
ring (19), and Lower Cone (15).
place. Apply one drop of 3M adhesive to all
screws and Drive Pins (2). 7. Install Brass Shear Screws (9) securely
through Lower Cone (15) into flat bottom holes
10.File off all wrench marks.
on Body (1).
Sizes 535-32 and 546-32
8. Adjust the position of the Upper Cone (8) so
1. Body Lock Ring (4) should not shoulder up that all components between Cones are snug
against the Top Sub (6) or Upper Slip (5). Body but able to be rotated easily. Loosely install
Lock Ring should be visible through inspection Brass Shear Screws (9) through Upper Cone
hole. into slots on Body (1).
2. Fully tighten Brass Shear Screws (9). Apply NOTE: Wire Mesh Back-Up Rings (12) must not be
one drop of Carem #214. expanded and Packing Element (14) must not be
Unit No. 8277 10-1-03 Models “HE” And “HEA” Retainer Production
Rev. New Page 6 of 15 Packers And Model “B-2” Hydraulic-Set Adapter
buckled. Once the Upper Cone (8) is in the proper 2. Verify the box threads and seal profile have
position, tighten down Brass Shear Screws (9) been glass bead peened.
securely.
3. Clean the box and pin connections with a light,
9. Install Adjusting Nut (17), Key (16), and Lower non-oily cleaner or (mek).
Slip (5). Fill cavity in Lower Cone (15) with Shell
4. Grease with Baker Downhole grease, Product
Darina #2 or equivalent and assemble on Body
Number 499-21, and make up all connections
(1).
without Crush Rings.
NOTE: The beveled end of the Adjusting Nut (17)
must not be placed against the Lower Slip (5).
5. Drift the assembled packer and SBEs with the
Adjust the Adjusting Nut until the Lower Slip is snug. Drift Bar specified below:
Securely install Brass Set Screws (9). SBE Size Drift Bar
10.Slide (do not rotate) the Support Ring (3) and 26 T-12902
Body Lock Ring (4) as a unit against the Upper 30 T-13179
Slip (5). A rubber mallet may be used to bump 32 T-12913
the Support Ring down. Rotate the Support 6. Mark a make up symbol across each box and
Ring down until Upper Slip is able to hand turn pin connection.
easily. The Body Lock Ring should appear in
7. Break the connections and re-clean threads.
the middle of the Support Ring inspection hole
1/2 to 1/4 view filled. 8. Spray the box, pin, seal profiles, and Crush
Rings with light, even coats of “molly spray”
11.Drill to the diameter and depth specified on the
(Molybdenum Disulphide).
assembly drawing through Support Ring (3)
into the Upper Bore Receptacle (23) then install 9. Apply Never-Seez thread compound to pin seal
Drive Pins (2). and Crush Ring ID and assemble Crush Ring
on pin end.
12.Apply one drop of 3M adhesive to Brass Shear
Screw (9) heads and Drive Pin (2) heads. 10.Re-apply a light, even coat of Never-Seez over
the entire pin and box threads and seal profiles.
Sizes 396-26 x 19 and 425-30 x 22.
11.Hand thread and bump tight with a wrench,
1. Body Lock Ring (4) should not shoulder up
making certain that the same box and pins are
against the Body (1) or Upper Slip (5). Body
used together as were assembled in Step 5.
Lock Ring should be visible through
12.Place the assembly in the bucking unit, making
2. Fully tighten Brass Shear Screws (9). Apply
certain that both ends are level. Make up by
one drop of Carem #214.
gradually increasing torque until make up lines
3. Use downhole grease on all straight threads. meet exactly.
4. Lightly grease ID of Packing Element (14) with 13.Before installing the bottom sub or crossover,
non-petroleum based grease. the torqued-up assembly must pass proper drift
5. Secure assembly with lead pads whenever bar as specified in Step 6.
supported by hand vice. 14.Plug the packer with the bull plug specified on
6. Torque connections with bucking unit. the packer assembly drawing, and plug the bot-
7. Splits in Packer Rings (11) and Cone Rings tom sub with the proper threaded bull plug.
(10) should be 180° apart. 15.Pressure test the entire assembly to the rated
8. Packing Element (14) System should be tightly working pressure for 15 minutes.
hand snugged in order for Packer Rings (11)
and Cone Rings (10) not to be able to hand ro- Parts List for Seal Bore Extensions
tate after inserting Brass Shear Screws (9) into Size Size 26 Size 32
Upper Cone (8). 10 ft. Box x Pin 499-42-2601 499-42-3201
10 ft. Pin x Pin 499-42-2602 499-42-3202
Seal Bore Extension 20 ft. Pin x Pin 499-42-2600 499-42-3200
1. Secure the assembly or component with lead 30 ft. Pin x Pin 499-42-2604 499-42-3203
pads whenever supported by a hand vise. Bottom Sub 499-42-26XX 499-42-32XX
NOTE: All Seal Bore Extensions are supplied with crush
rings.
Model “HE” Retainer Production Packers
Dimensional Data
Refer to Drawing No. 297-859-1.
Rev. New
Unit No. 8277
Packer Dim
Size A B C D E F G H
381-26 3.812 9-7/8 5-7/8 3-1/4" Baker 39-1/2 3.514 28-1/2
396-26 3.968 9-3/4 5-5/8 Left-Hand 45 2.688 3.658 30
425-26 4.250 9-7/8 5-7/8 Sq. Thd. 36-11/16 3.937 24-3/8
535-32 5.350 4" Baker
11-5/8 7-5/8 47-5/8 5 34-1/2
546-32 5.468 Left-Hand 3.248
Page 7 of 15
568.32 5.688 14-1/2 9-1/4 Sq. Thd. 46-3/4 5.360 37-1/2
10-1-03
Model “HEA” Retainer Production Packers
Rev. New
Unit No. 8277
Assembly And Dimensional Data Drawing No. 276-722-1
Page 8 of 15
10-1-03
Packers And Model “B-2” Hydraulic-Set Adapter
Models “HE” And “HEA” Retainer Production
Dimensional Data
Refer to Drawing No. 276-722-1.
Packer Dim
Size A B C D E F G H J K
3-1/4 Baker
2-3/8
375-26 x 19 - - 3.750 Left-Hand - 53-1/8 18-1/2 3.514 45-3/4
5.1#
Sq. Thd.
VAM -A
396-26 x 19 - - 54-3/4 18-9/16 3.600 43-11/16
3.625 OD
2-7/8
Left-Hand
425-30 x 22 3.000 4.250 - 52 16-15/16 3.745 38-1/2 7.7#
Special Butt
VAM-A
Thd.
Size 375-26 x 19 has a 2-piece body.
Model “HE” And “HEA” Retainer Production Packers
Rev. New
Unit No. 8277
23 Upper Bore Receptacle 1 02-82360-02
26 Coupling 1 469-10-2101
YNumber in [ ] indicates quantity required.
Page 9 of 15
10-1-03
Model “HE” And “HEA” Retainer Production Packers
Rev. New
Unit No. 8277
Parts List, Sizes 425-26, 425-30 x 22, 535-32, 546-32 and 568-32
Refer to Drawing Nos. 297-859-1 and 276-722-1.
Item No. Size of Packer
Description
No. Req’d 425-26 425-30 x 22 535-32 546-32 568-32
1 Body 1 02-92847-00 02-93746-01 02-81388-00 02-81388-06 02-83666-00
2 Drive Pin 4 01-31660-00 01-32999-00 01-31660-00
Page 10 of 15
3 Support Ring 1 02-77952-00 02-81361-00 02-79423-00 02-79842-00
4 Body Lock Ring 1 02-77953-00 02-79432-00 02-79843-00
10-1-03
5 Slip (Upper/Lower) 2 02-77954-00 02-61961-01 01-40345-00 02-84901-00
6 Top Sub 1 02-82507-00 02-81360-00 02-81360-00 02-83666-00
N/A
7 Hex Socket Set Screw Y WW-G51B-080 [2] WW-G51B-0H0 [2] WW-G51B-0D0 [6]
8 Upper Cone 1 02-93284-00 02-81362-00 02-81428-00 02-83667-00
9 Brass Shear Screw Y WW-GE18-0DB [6] WW-GE18-0MB[6] WW-GE18-0FC [6]
Rev. New
Unit No. 8277
Page 11 of 15
10-1-03
Unit No. 8277 10-1-03 Models “HE” And “HEA” Retainer Production
Rev. New Page 12 of 15 Packers And Model “B-2” Hydraulic-Set Adapter