Вы находитесь на странице: 1из 32

FILE NO.

050-200408

SERVICE MANUAL

COLOR TELEVISION

13A24

DOCUMENT CREATED IN JAPAN, Mar., 2004


SERVICING NOTICES ON CHECKING
1. KEEP THE NOTICES 6. AVOID AN X-RAY
As for the places which need special attentions, Safety is secured against an X-ray by consider-
they are indicated with the labels or seals on the ing about the cathode-ray tube and the high
cabinet, chassis and parts. Make sure to keep the voltage peripheral circuit, etc.
indications and notices in the operation manual. Therefore, when repairing the high voltage pe-
ripheral circuit, use the designated parts and
2. AVOID AN ELECTRIC SHOCK make sure not modify the circuit.
There is a high voltage part inside. Avoid an Repairing except indicates causes rising of high
electric shock while the electric current is voltage, and it emits an X-ray from the cathode-
flowing. ray tube.
3. USE THE DESIGNATED PARTS 7. PERFORM A SAFETY CHECK AFTER
The parts in this equipment have the specific SERVICING
characters of incombustibility and withstand
Confirm that the screws, parts and wiring which
voltage for safety. Therefore, the part which is
were removed in order to service are put in the
replaced should be used the part which has
original positions, or whether there are the
the same character.
portions which are deteriorated around the
Especially as to the important parts for safety
serviced places serviced or not. Check the
which is indicated in the circuit diagram or the
insulation between the antenna terminal or
table of parts as a mark, the designated
external metal and the AC cord plug blades.
parts must be used.
And be sure the safety of that.
4. PUT PARTS AND WIRES IN THE (INSULATION CHECK PROCEDURE)
ORIGINAL POSITION AFTER
1. Unplug the plug from the AC outlet.
ASSEMBLING OR WIRING 2. Remove the antenna terminal on TV and turn
There are parts which use the insulation on the TV.
material such as a tube or tape for safety, or 3. Insulation resistance between the cord plug
which are assembled in the condition that terminals and the eternal exposure metal
these do not contact with the printed board. [Note 2] should be more than 1M ohm by
The inside wiring is designed not to get closer using the 500V insulation resistance meter
to the pyrogenic parts and high voltage parts. [Note 1].
Therefore, put these parts in the original 4. If the insulation resistance is less than 1M
positions. ohm, the inspection repair should be
required.
5. TAKE CARE TO DEAL WITH THE
[Note 1]
CATHODE-RAY TUBE
If you have not the 500V insulation
In the condition that an explosion-proof cathode-
resistance meter, use a Tester.
ray tube is set in this equipment, safety is
secured against implosion. However, when [Note 2]
removing it or serving from backward, it is External exposure metal: Antenna terminal
dangerous to give a shock. Take enough care to Earphone jack
deal with it.

HOW TO ORDER PARTS


Please include the following informations when you order parts. (Particularly the VERSION LETTER.)
1. MODEL NUMBER and VERSION LETTER
The MODEL NUMBER can be found on the back of each product and the VERSION LETTER can be
found at the end of the SERIAL NUMBER.
2. PART NO. and DESCRIPTION
You can find it in your SERVICE MANUAL.

IMPORTANT
Inferior silicon grease can damage IC's and transistors.
When replacing an IC's or transistors, use only specified silicon grease (YG6260M).
Remove all old silicon before applying new silicon.

A1-1
CONTENTS

SERVICING NOTICES ON CHECKING ...................................................................................................... A1-1


HOW TO ORDER PARTS ........................................................................................................................... A1-1
IMPORTANT ................................................................................................................................................ A1-1
CONTENTS ................................................................................................................................................. A2-1
GENERAL SPECIFICATIONS .................................................................................................................... A3-1~A3-5
DISASSEMBLY INSTRUCTIONS
1.REMOVAL OF ANODE CAP .............................................................................................................. B1-1
2.REMOVAL AND INSTALLATION OF FLAT PACKAGE IC ............................................................... B2-1, B2-2
SERVICE MODE LIST ................................................................................................................................. C-1
CONFIRMATION OF HOURS USED .......................................................................................................... C-1
WHEN REPLACING EEPROM( MEMORY) IC ........................................................................................... C-1
ELECTRICAL ADJUSTMENTS .................................................................................................................. D-1~D-4
BLOCK DIAGRAM ...................................................................................................................................... E-1, E-2
PRINTED CIRCUIT BOARDS
MAIN/CRT ............................................................................................................................................... F-1~F-4
SCHEMATIC DIAGRAMS
MICON/CHROMA/TUNER ...................................................................................................................... G-1, G-2
TV POWER ............................................................................................................................................. G-3, G-4
DEFLECTION/CRT ................................................................................................................................. G-5, G-6
SOUND/AV ............................................................................................................................................. G-7, G-8
WAVEFORMS ............................................................................................................................................. H-1, H-2
MECHANICAL EXPLODED VIEW .............................................................................................................. I-1, I-2
MECHANICAL REPLACEMENT PARTS LIST .......................................................................................... J1-1
ELECTRICAL REPLACEMENT PARTS LIST ............................................................................................ J2-1~ J2-3

A2-1
GENERAL SPECIFICATIONS
G-1 TV CRT CRT Size / Visual Size 13 inch / 335.4mmV
System CRT Type Normal
Deflection 90 degree
Magnetic Field BV/BH +0.45G/0.18G
Color System NTSC
Speaker 1Speaker
Position Bottom
Size 3 Inch
Impedance 8 ohm
Sound Output MAX 1.0 W
10%(Typical) 0.8 W
NTSC3.58+4.43 /PAL60Hz No
G-2 Tuning Broadcasting System US System M
System Tuner and System 1Tuner
Receive CH Destination USA(W/ CATV)
Tuning System F-Synth
Input Impedance VHF/UHF 75 ohm
2 - 69, 4A, A-5 - A-1,
CH Coverage A - I, J - W, W+1 - W+84
Intermediate Picture(FP) 45.75MHz
Frequency Sound(FS) 41.25MHz
FP-FS 4.50MHz
Preset CH No
Stereo/Dual TV Sound No
Tuner Sound Muting Yes
G-3 Power Power Source AC 120V AC 60Hz
DC
Power Consumption at AC
54 W at AC 120 V 60 Hz
Stand by (at AC) 5 W at AC 120 V 60 Hz
Per Year -- kWh/Year
Protector Power Fuse Yes
G-4 Regulation Safety UL / CSA
Radiation FCC / IC
X-Radiation DHHS / HWC
G-5 Temperature Operation +5oC ~ +40oC
Storage -20oC ~ +60oC
G-6 Operating Humidity Less than 80% RH

A3-1
GENERAL SPECIFICATIONS
G-7 On Screen Menu Yes
Display Menu Type Character
Picture Yes
Contrast Yes
Brightness Yes
Color Yes
Tint Yes
Sharpness Yes
Audio No
Bass No
Treble No
Balance No
BBE On/Off No
Stable Sound On/Off No
CH Set Up Yes
TV/CABLE(CATV) Yes
Auto CH Memory Yes
Add/ Delete Yes
Language Yes
V-chip Yes
Lock Yes
On Timer Yes
CH Label No
Favorite CH No
Color Stream DVD/DTV No
Control Level Yes
Volume Yes
Brightness Yes
Contrast Yes
Color Yes
Tint Yes
Sharpness Yes
Tuning No
Bass No
Treble No
Balance No
Back Light No
Stereo,Audio Output,SAP No
Video Yes
Color Stream No
Channel(TV/Cable) Yes
CH Label No
Game Timer Yes
Sleep Timer Yes
Sound Mute Yes
V-chip Rating Yes
G-8 OSD Language English French Spanish

G-9 Clock and Sleep Timer Max Time 120 Min


Timer Step 10 Min
On Timer Program(On Timer ) Yes
Wake Up Timer No
Timer Back-up (at Power Off Mode) more than -- Min Sec

A3-2
GENERAL SPECIFICATIONS
G-10 Remote Unit RC-EH
Control Glow in Dark Remocon Yes
Format Toshiba
Custom Code 40-BF h
Power Source Voltage(D.C) 3V
UM size x pcs UM-4 x 2 pcs
Total Keys 27 Keys
Keys Power Yes
1 Yes
2 Yes
3 Yes
4 Yes
5 Yes
6 Yes
7 Yes
8 Yes
9 Yes
0 Yes
100 No
CH Up Yes
CH Down Yes
Volume Up Yes
Volume Down Yes
TV/Caption/Text Yes
CH1/CH2 Yes
TV/Video(TV/AV) Yes
CH RTN/CH ENT(Quick View) Yes
Sleep Yes
RE Call(Call) Yes
Reset Yes
Menu Yes
Enter Yes
Mute Yes
Exit No
MTS(Audio Select) No
Set + Yes
Set - Yes
Multi Brand Keys CH Up(VCR) No
CH Down(VCR) No
Pause/Still No
TV/VCR(VCR) No
Code No
FF No
Rew No
Rec No
Play No
Stop No
TV No
VCR No
Cable No

A3-3
GENERAL SPECIFICATIONS
G-11 Features Auto Degauss Yes
Auto Shut Off Yes
Canal+ No
CATV Yes
Anti-theft No
Rental No
Memory(Last CH) Yes
Memory(Last Volume) Yes
V-Chip Yes
Type USA,ORION Type
BBE No
Auto Search No
CH Allocation No
SAP No
Channel Lock No
Just Clock Function No
Game Position No
CH Label No
VM Circuit No
Full OSD No
Premiere No
Comb Filter No
Lines
Auto CH Memory Yes
Hotel Lock No
Closed Caption Yes
FBT Leak Test Protect Yes
CH Lock Yes
Video Lock Yes
Game Timer (Max Time:120 Min) Yes
Stable Sound No
Energy Star No
Power On Memory Yes
Favorite CH No
G-12 Accessories Owner's Manual Language English / Spanish / French
w/Guarantee Card Yes
Remote Control Unit Yes
Rod Antenna No
Poles
Terminal
Loop Antenna No
Terminal -
U/V Mixer No
DC Car Cord (Center+) No
Guarantee Card No
Warning Sheet No
Circuit Diagram No
Antenna Change Plug No
Service Facility List No
Important Safeguard No
Dew/AHC Caution Sheet No
AC Plug Adapter No
Quick Set-up Sheet No
Battery Yes
UM size x pcs UM-4 x 2 pcs
OEM Brand No
AC Cord No
AV Cord (2Pin-1Pin) No
Registration Card (NDL Card) Yes
ESP Card No[From '04 MAR O/R]
300 ohm to 75 ohm Antenna Adapter No

A3-4
GENERAL SPECIFICATIONS
G-13 Interface Switch Front Power Yes
System Select No
Main Power SW No
Sub Power No
Channel Up/Reset Yes
Channel Down/Enter Yes
Volume Up/Set Up Yes
Volume Down/Set Down Yes
MENU=Volume Up+Volume Down Yes
Rear AC/DC No
TV/CATV Selector No
Degauss No
Main Power SW No
Indicator Power Yes
Stand-by No
On Timer No
Terminals Front Video Input RCA
Audio Input RCA x 1
Other Terminal Ear Phone
Rear Video Input(Rear1) No
Video Input(Rear2) No
Audio Input(Rear1) No
Audio Input(Rear2) No
Video Output No
Audio Output No
Euro Scart No
Color Stream No
Diversity No
Ext Speaker No
DC Jack 12V(Center +) No
VHF/UHF Antenna Input F Type
AC Outlet No
G-14 Set Size Approx. W x D x H (mm) 362 x 360 x 320.5
G-15 Weight Net (Approx.) 9.5 kg ( 20.9 lbs)
Gross (Approx.) 11.0kg ( 24.4lbs)
G-16 Carton Master Carton No
Content ---- Sets
Material -- /--
Dimensions W x D x H(mm) -- x -- x --
Description of Origin No
Gift Box Yes
Material Double/Brown
Dimensions W x D x H(mm) 440 x 408 x 380
Design As per Buyer's
Description of Origin Yes
Drop Test Natural Dropping At 1 Corner / 3 Edges /
6 Surfaces
Height (cm) 62
Container Stuffing 866 Sets/40' container
G-17 Cabinet Material Cabinet Cabinet Front PS 94V0 DECABROM
Cabinet Rear PS 94V0 DECABROM
PCB Non-Halogen Demand No
Eyelet Demand Yes

A3-5
DISASSEMBLY INSTRUCTIONS
1. REMOVAL OF ANODE CAP 3. After one side is removed, pull in the opposite direction to
remove the other.
Read the following NOTED items before starting work.
NOTE
* After turning the power off there might still be a potential
voltage that is very dangerous. When removing the Take care not to damage the Rubber Cap.
Anode Cap, make sure to discharge the Anode Cap's INSTALLATION
potential voltage.
1. Clean the spot where the cap was located with a small
* Do not use pliers to loosen or tighten the Anode Cap
amount of alcohol. (Refer to Fig. 1-3.)
terminal, this may cause the spring to be damaged.
REMOVAL
1. Follow the steps as follows to discharge the Anode Cap. Location of Anode Cap
(Refer to Fig. 1-1.)
Connect one end of an Alligator Clip to the metal part of a
flat-blade screwdriver and the other end to ground.
While holding the plastic part of the insulated Screwdriver,
touch the support of the Anode with the tip of the
Screwdriver.
A cracking noise will be heard as the voltage is discharged.

Fig. 1-3

GND on the CRT NOTE


Confirm that there is no dirt, dust, etc. at the spot where
the cap was located.
2. Arrange the wire of the Anode Cap and make sure the
wire is not twisted.
3. Turn over the Rubber Cap. (Refer to Fig. 1-4.)

Screwdriver CRT
Support
Alligator Clip
Fig. 1-4
GND on the CRT Fig. 1-1
4. Insert one end of the Anode Support into the anode button,
2. Flip up the sides of the Rubber Cap in the direction of the then the other as shown in Fig. 1-5.
arrow and remove one side of the support.
(Refer to Fig. 1-2.)

Rubber Cap

Support
CRT
Fig. 1-5
CRT
Support 5. Confirm that the Support is securely connected.
Fig. 1-2
6. Put on the Rubber Cap without moving any parts.

B1-1
DISASSEMBLY INSTRUCTIONS
2. REMOVAL AND INSTALLATION OF 3. When IC starts moving back and forth easily after
desoldering completely, pickup the corner of the IC using a
FLAT PACKAGE IC tweezers and remove the IC by moving with the IC
desoldering machine. (Refer to Fig. 2-3.)
REMOVAL
NOTE
1. Put the Masking Tape (cotton tape) around the Flat
Some ICs on the PCB are affixed with glue, so be
Package IC to protect other parts from any damage. careful not to break or damage the foil of each IC leads
(Refer to Fig. 2-1.) or solder lands under the IC when removing it.
NOTE
Masking is carried out on all the parts located within 10 Blower type IC
mm distance from IC leads. desoldering
machine

Masking Tape IC
(Cotton Tape)

Tweezers

Fig. 2-1
IC
Fig. 2-3
2. Heat the IC leads using a blower type IC desoldering
machine. (Refer to Fig. 2-2.)
4. Peel off the Masking Tape.
NOTE
Do not add the rotating and the back and forth 5. Absorb the solder left on the pattern using the Braided
directions force on the IC, until IC can move back and Shield Wire. (Refer to Fig. 2-4.)
forth easily after desoldering the IC leads completely. NOTE
Do not move the Braided Shield Wire in the vertical
direction towards the IC pattern.
Blower type IC
desoldering machine

Braided Shield Wire

Soldering Iron

IC
IC pattern
Fig. 2-2 Fig. 2-4

B2-1
DISASSEMBLY INSTRUCTIONS
INSTALLATION 4. When bridge-soldering between terminals and/or the
soldering amount are not enough, resolder using a Thin-tip
1. Take care of the polarity of new IC and then install the new Soldering Iron. (Refer to Fig. 2-8.)
IC fitting on the printed circuit pattern. Then solder each
lead on the diagonal positions of IC temporarily.
(Refer to Fig. 2-5.)
Thin-tip Soldering Iron IC

Soldering Iron

Fig. 2-8

5. Finally, confirm the soldering status on four sides of the IC


Solder temporarily Solder temporarily
using a magnifying glass.
Confirm that no abnormality is found on the soldering
Fig. 2-5 position and installation position of the parts around the IC.
If some abnormality is found, correct by resoldering.
2. Supply the solder from the upper position of IC leads NOTE
sliding to the lower position of the IC leads.
When the IC leads are bent during soldering and/or
(Refer to Fig. 2-6.)
repairing, do not repair the bending of leads. If the
bending of leads are repaired, the pattern may be
damaged. So, always be sure to replace the IC in this
case.

Solder Soldering Iron

IC Supply soldering
from upper position
to lower position

Fig. 2-6

3. Absorb the solder left on the lead using the Braided Shield
Wire. (Refer to Fig. 2-7.)
NOTE
Do not absorb the solder to excess.

Soldering Iron
IC

Braided Shield Wire

Fig. 2-7

B2-2
SERVICE MODE LIST
This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily.
To enter the Service Mode, press both set key and remote control key for more than 1 second.

Set Key Remocon Key Operations


VOL. (-) MIN 0 Releasing of V-CHIP PASSWORD.
Initialization of the factory.
NOTE: Do not use this for the normal servicing.
VOL. (-) MIN 1
If you set a factory initialization, the memories are reset such as the channel setting,
and the POWER ON total hours.
POWER ON total hours is displayed on the screen.
Refer to the "CONFIRMATION OF HOURS USED".
VOL. (-) MIN 6
Can be checked of the INITIAL DATA of MEMORY IC.
Refer to the "WHEN REPLACING EEPROM (MEMORY) IC".
Writing of EEPROM initial data.
VOL. (-) MIN 8
NOTE: Do not use this for the normal servicing.
Display of the Adjustment MENU on the screen.
VOL. (-) MIN 9
Refer to the "ELECTRICAL ADJUSTMENT" (On-Screen Display Adjustment).

CONFIRMATION OF HOURS USED


POWER ON total hours can be checked on the screen. Total hours are displayed in 16 system of notation.
NOTE: If you set a factory initialization, the total hours is reset to "0".
1. Set the VOLUME to minimum. ADDRESS DATA

2. Press both VOL. DOWN button on the set and Channel


button (6) on the remote control for more than 1 second.
3. After the confirmation of using hours, turn off the power. INIT 00 50 Initial setting content of MEMORY IC.
CRT ON 0010 POWER ON total hours.
= (16 x 16 x 16 x thousands digit value)
+ (16 x 16 x hundreds digit value)
+ (16 x tens digit value)
FIG. 1 + (ones digit value)

WHEN REPLACING EEPROM (MEMORY) IC


If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to
ensure correct data settings while making reference to TABLE 1.
NOTE: No need setting for after INI 0F due to the adjustment value.

INI +0 +1 +2 +3 +4 +5 +6 +7 +8 +9 +A +B +C +D +E +F
00 50 04 EB 4E 07 B3 24 69 39 00 00 05 90 D6 00 07

Table 1
1. Enter DATA SET mode by setting VOLUME to minimum.
2. Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 1 second.
ADDRESS and DATA should appear as FIG 1.
3. ADDRESS is now selected and should "blink". Using the VOL. +/- button on the remote, step through the ADDRESS until
required ADDRESS to be changed is reached.
4. Press ENTER to select DATA. When DATA is selected, it will "blink".
5. Again, step through the DATA using VOL. +/- button until required DATA value has been selected.
6. Pressing ENTER will take you back to ADDRESS for further selection if necessary.
7. Repeat steps 3 to 6 until all data has been checked.
8. When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input.
After the data input, set to the initializing of shipping.
9. Turn POWER on.
10. Press both VOL. DOWN button on the set and Channel button (1) on the remote control for more than 1 second.
11. After the finishing of the initializing of shipping, the unit will turn off automatically.
The unit will now have the correct DATA for the new MEMORY IC.

C-1
ELECTRICAL ADJUSTMENTS
1. ADJUSTMENT PROCEDURE 2. BASIC ADJUSTMENTS
Read and perform these adjustments when repairing the
circuits or replacing electrical parts or PCB assemblies. 2-1: CUT OFF

CAUTION 1. Adjust the unit to the following settings.


• Use an isolation transformer when performing any service R.DRIVE=10, B.DRIVE=10, R.BIAS=64, G.BIAS=64,
on this chassis. B.BIAS=64, BRI.CENT=120, CONT.MAX=40.
• Before removing the anode cap, discharge electricity 2. Place the set with Aging Test for more than 15 minutes.
because it contains high voltage. 3. Activate the adjustment mode display of Fig. 1-1 and
• When removing a PCB or related component, after press the channel button (01) on the remote control to
unfastening or changing a wire, be sure to put the wire select "CUT OFF".
back in its original position. 4. Adjust the Screen Volume until a dim raster is obtained.
• When you exchange IC and Transistor for a heat sink,
2-2: WHITE BALANCE
apply the silicon grease on the contact section of the heat
sink. Before applying new silicon grease, remove all the NOTE: Adjust after performing CUT OFF adjustment.
old silicon grease. (Old grease may cause damages to the 1. Place the set with Aging Test for more than 10 minutes.
IC and Transistor.) 2. Receive the gray scale pattern from the Pattern Generator.
Prepare the following measurement tools for electrical 3. Using the remote control, set the brightness and contrast
adjustments. to normal position.
1. Oscilloscope 4. Activate the adjustment mode display of Fig. 1-1 and
2. Digital Voltmeter press the channel button (10) on the remote control to
3. Pattern Generator select “R. BIAS”.
5. Press the CH. UP/DOWN button on the remote control to
On-Screen Display Adjustment select the “R. BIAS”, “G. BIAS”, “B. BIAS”, “R. DRIVE” or
1. In the condition of NO indication on the screen. “B. DRIVE”.
Press the VOL. DOWN button on the set and the Channel 6. Adjust the VOL. UP/DOWN button on the remote control
button (9) on the remote control for more than 1 second to to whiten the R. BIAS, G. BIAS, B. BIAS, R. DRIVE, and
appear the adjustment mode on the screen as shown in B. DRIVE at each step tone sections equally.
Fig. 1-1. 7. Perform the above adjustments 5 and 6 until the white
color is looked like a white.

TV 2-3: FOCUS
1. Receive the monoscope pattern.
2. Turn the Focus Volume fully counterclockwise once.
3. Adjust the Focus Volume until picture is distinct.

00 OSD 23 2-4: HORIZONTAL PHASE


Fig. 1-1 1. Receive the monoscope pattern.
2. Using the remote control, set the brightness and contrast
3. Use the Channel UP/DOWN button or Channel button to normal position.
(0-9) on the remote control to select the options shown 3. Activate the adjustment mode display of Fig. 1-1 and
in Fig. 1-2. press the channel button (05) on the remote control to
4. Press the MENU button on the remote control to end the select “H. PHAS”.
adjustments. 4. Press the VOL. UP/DOWN button on the remote control
until the SHIFT quantity of the OVER SCAN on right and
NO. FUNCTION NO. FUNCTION left becomes minimum.
00 OSD H 16 CONTRAST CENT
01 CUT OFF 17 CONTRAST MAX 2-5: VERTICAL SHIFT
04 H. VCO 18 CONTRAST MIN
1. Receive the monoscope pattern.
05 H. PHASE 19 COLOR CENTER
06 V. SIZE 20 COLOR MAX
2. Using the remote control, set the brightness and contrast
07 V. SHIFT 21 COLOR MIN to normal position.
08 R DRIVE 22 TINT 3. Activate the adjustment mode display of Fig. 1-1 and
09 B DRIVE 23 SHARPNESS press the channel button (07) on the remote control to
10 R BIAS 24 FM LEVEL select “V. SFT”.
11 G BIAS 25 LEVEL 4. Press the VOL. UP/DOWN button on the remote control
12 B BIAS 26 SEPARATION1 until the horizontal line becomes fit to the notch of the
13 BRIGHT CENT 27 SEPARATION2
shadow mask.
14 BRIGHT MAX 28 TEST MONO
15 BRIGHT MIN 29 TEST STEREO
Fig. 1-2

D-1
ELECTRICAL ADJUSTMENTS
2-6: VERTICAL SIZE
1. Receive the monoscope pattern.
2. Using the remote control, set the brightness and contrast
to normal position.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (06) on the remote control to
select “V. SIZE”.
4. Press the VOL. UP/DOWN button on the remote control
until the SHIFT quantity of the OVER SCAN on upside and
downside becomes 10 ± 2%.

2-7: SUB BRIGHTNESS white 100% red 110% Fig. 2-2


1. Receive the monoscope pattern. (RF Input)
2. Using the remote control, set the brightness and contrast 2-9: SUB CONTRAST
to normal position.
3. Activate the adjustment mode display of Fig. 1-1 and 1. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (13) on the remote control to press the channel button (17) on the remote control to
select "BRI.CENT". select “CONT. MAX”.
4. Press the VOL. UP/DOWN button on the remote control 2. Press the VOL. UP/DOWN button on the remote control
until the white 0% is starting to be visible until the contrast step No. becomes “48”.
5. Receive the monoscope pattern. (Audio Video Input) 3. Receive a broadcast and check if the picture is normal.
6. Press the TV/VIDEO button on the remote control to set 4. Press the TV/VIDEO button on the remote control to set to
to the AV mode. Then perform the above adjustments the AV mode.
2~4. 5. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (17) on the remote control to
2-8: SUB TINT/SUB COLOR select “CONT. MAX”.
6. Press the VOL. UP/DOWN button on the remote control
1. Receive the color bar pattern. until the contrast step No. becomes “55”.
2. Connect the oscilloscope to TP023. 7. Receive a broadcast and check if the picture is normal.
3. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (22) on the remote control to 2-10: OSD HORIZONTAL
select "TINT".
4. Press the VOL. UP/DOWN button on the remote control 1. Activate the adjustment mode display of Fig. 1-1.
until the section "A" becomes as straight line 2. Press the VOL. UP/DOWN button on the remote control
(Refer to Fig. 2-1) until the difference of A and B becomes minimum.
5. Connect the oscilloscope to TP022. (Refer to Fig. 2-3)
6. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (19) on the remote control to
select "COL.CENT". TV
7. Press the VOL. UP/DOWN button on the remote control
until the red color level is adjusted to 110 ± 10% of the
white level. (Refer to Fig. 2-2)
8. Receive the color bar pattern. (Audio Video Input)
9. Press the TV/VIDEO button on the remote control to set
to the AV mode. Then perform the above adjustments 00 OSD 23
2~7
A B Fig. 2-3

2-11: Confirmation of Fixed Value (Step No.)


Please check if the fixed values of the each adjustment
items are set correctly referring below. (RF/AV)
NO. FUNCTION STEP NO. NO. FUNCTION STEP NO.
"A" 04 H. VCO 04 21 COLOR MIN 00
14 BRIGHT MAX 140 23 SHARPNESS 53
15 BRIGHT MIN 60 24 FM LEVEL 00
16 CONTRAST CENT 30 25 LEVEL 00
Fig. 2-1 18 CONTRAST MIN 15 26 SEPARATION1 00
20 COLOR MAX 74 27 SEPARATION2 00

D-2
ELECTRICAL ADJUSTMENTS
3. PURITY AND CONVERGENCE 3-3: STATIC CONVERGENCE
ADJUSTMENTS NOTE
NOTE Adjust after performing adjustments in section 3-2.
1. Turn the unit on and let it warm up for at least 30 1. Receive the crosshatch pattern from the color bar
minutes before performing the following adjustments. generator.
2. Place the CRT surface facing east or west to reduce the 2. Combine red and blue of the 3 color crosshatch
terrestrial magnetism. pattern on the center of the screen by adjusting the pair
3. Turn ON the unit and demagnetize with a Degauss Coil. of 4 pole magnets.
3. Combine red/blue (magenta) and green by adjusting the
3-1: STATIC CONVERGENCE (ROUGH ADJUSTMENT) pair of 6 pole magnets.
1. Tighten the screw for the magnet. Refer to the adjusted
3-4: DYNAMIC CONVERGENCE
CRT for the position. (Refer to Fig. 3-1)
If the deflection yoke and magnet are in one body, NOTE
untighten the screw for the body. Adjust after performing adjustments in section 3-3.
2. Receive the green raster pattern from the color bar
generator. 1. Adjust the differences around the screen by moving the
3. Slide the deflection yoke until it touches the funnel side deflection yoke upward/downward and right/left.
of the CRT. (Refer to Fig. 3-2-a)
4. Adjust center of screen to green, with red and blue on 2. Insert three wedges between the deflection yoke and
the sides, using the pair of purity magnets. CRT funnel to fix the deflection yoke.
5. Switch the color bar generator from the green raster (Refer to Fig. 3-2-b)
pattern to the crosshatch pattern. RGB RGB
6. Combine red and blue of the 3 color crosshatch
pattern on the center of the screen by adjusting the pair
of 4 pole magnets. R
7. Combine red/blue (magenta) and green by adjusting the G
pair of 6 pole magnets. B R
8. Adjust the crosshatch pattern to change to white by
G
repeating steps 6 and 7.
B
UPWARD/DOWNWARD SLANT RIGHT/LEFT SLANT
3-2: PURITY
NOTE Fig. 3-2-a

Adjust after performing adjustments in section 3-1.


1. Receive the green raster pattern from color bar generator.
2. Adjust the pair of purity magnets to center the color on
the screen.
Adjust the pair of purity magnets so the color at the ends WEDGE WEDGE
are equally wide.
3. Move the deflection yoke backward (to neck side)
slowly, and stop it at the position when the whole screen
is green.
4. Confirm red and blue color.
5. Adjust the slant of the deflection yoke while watching the WEDGE
screen, then tighten the fixing screw.
DEFLECTION YOKE WEDGE POSITION
DEFLECTION YOKE SCREW Fig. 3-2-b
MAGNET SCREW

PURITY MAGNETS
6 POLE MAGNETS
4 POLE MAGNETS
Fig. 3-1

D-3
ELECTRICAL ADJUSTMENTS
4. ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE (WIRING CONNECTION)

CRT PCB

CP806

R8
B
03

03
P8

R8
TP022

07
CP803A TU001
FB401 TP023

01

01
4
CP

J8
CP802B
CP801

TP001

CD801
CR
T
DY

GND CRT
DEGAUSS COIL
L503

CP502

S501B
CP802A

AC IN
S501A

CD101B

CD101A SPEAKER

MAIN PCB

D-4
BLOCK DIAGRAM

TU001
10 11 12 13 17
2
EAR PHONE_JACK
3 J1001
CH. DOWN
1
IC1001 AN7511
VOL. DOWN MICON/CHROM
IC101 OEC7091B 2 6
21 20 34 SPEAKER
SOUND AMP SP1001
CH. UP
4 IC 8
66 ATT
VOL. UP RGB Proc.2
73 OSD SW Q801
67 CONTRAST BRIGHTNESS 50 RED OUT
POWER Chroma RGB OUTPUT Stage
68 Proc. DRIVE 51
Q802
I/O ACC/C-BPF CUT OFF
69 52
OS101 IIC APC/KILLER HV BLK GREEN OUT
70 RGB Proc.1 MCU
TIM TINT/DEMO
1 RGB MATRIX CLK Q607
74 INT
COLOR CONT Q803
PWM H-CTL
78 BLUE OUT
AD
Ver.Proc. Hor.Proc.
OSD
Ver SYNC SEP 46
SYNC SEPA/Hor. VCO
Ver.COUNT DOWN 45
ROM V RAMP Hor.COUNT DOWN
RAM AFC-1/H COINCIDENT Q402
J703
AFC-2 H PHASE
H. DRIVE

2 Q401
VCXO H. OUTPUT
J702

2
56 58 57 27 26 37 38 16 3 9 7
X601 B G R
Q505 3.579545MHz CRT
Heater
P. FAIL
V-OUT IC 4 F 8
IC501 IC401 LA78040N-E
T502 LTV-817M-VB Q507 5 6 MEMORY IC
4 FEED BACK PUMP UP
16 FEED BACK SW SDA SCL IC199
S-24C02BDP-1A -
AMP
8 Q502 +
DEGAUSS COIL
BUFFER L503 VCC
13
7 1 2 6 5 DY
6
Q501 D501~D504
SWITCHING RECTIFIER FB401

9
Q503 1 F
PROTECT DRV. 2 S
L501 10 HV
2 4
3
1 3

F501

AC IN
E-1 E-2
PRINTED CIRCUIT BOARDS
MAIN/CRT (INSERTED PARTS)
SOLDER SIDE

D408 CP601
C406

D404
R403

C435

HEATER
W003
D410

D411
R429
CP803A

GND

AFC
ABL
S101A C420_1

180V
W002
D405
W008
R410

W007 C403 C448_1

8V

12V
TU001
CP4 FB401
01

25V

COL
T401

B+
C434
C401_1

C007
D412
C440 C43
7
R408 R421

R404
C004
D001
C44 W001
W062 3 L401
Q402
W011 R542

Q401 W830

R409

D409
R446 HS501 D509
C446 R503
R448 Q501

D406

R427 W004

D512

R520
R506
R449

R401
C516 HS402
W010 C511 Q502

D506
1
40 C410_1 R508
IC R417
C510

C514_1
W072

W819
C509
R504
C002 D516 R510_1
W009
R424 R418 47
01 R4 D508
S4
H C414
D513 B501

R413

R501
C417_2

R405 W038

C526_1
C418

T502
C422

R509
W039
R514
C521
W037 C427
W015

R416
R415

IC501
D403
R002
L001

B504
C515 C517

C506
D502

D501
W036

R422
W834 D503
R001

W006
D505
R527 C503

D504
W050 C508
W049 C507 D510

C502
Q602 R445
W048 C518 D528
Q503 W005
W831 C617

W802
R523 W014 CP502
R52
W046 Q601 R6 5
R528

29 R518 D511
W067

TP401

R515

W019
C606 R516 Q603

1
R513

D515
W012

17_
R507 CP503
W035

R505
R537

R608 R602 R603


W070

R5
W034

Q505 D521 R512

C513_1
W810
W809

C601 R502
W832

C519
C106 Q606 TH501_1
W833

L501
W025
R423

L801
D606

D514

X601

RISK
C103
W073
W040

R519
R604

W024 Q507

_1
W023

CP806

03
R130
R119

W065

R8
C602 C623

OF FIRE
D522

S1
_1
4
R804
02
W059
D602

C615 W069

01
05

C
TP

P8

B
R8

_1
W064 W020

03
W058 C505
C8

07
C605

B
W057 R605 19

R8
W071

FH502
TP022 _1
W056

R601

4A125VOR250V

-
W816 C621 Q802
R802
W055 Q801

REPLACE
C616

J8
W018 TP023

F501
W054

01

R538
C620_1

C809
W803
W017

C622
W053 C610 C628 R815
W823 IC1001
R606 R811 R816 Q803
W828 W033
C1003
C624_1

W052

W051

C808

AS
R621 W068 C1005
C1001 R813 C810
C630
CP802A

R607 D604 S501B

FH501
W061
S102A

R809 R814

MARKED .

CD501
R1001

R614 W032
R611
R620

D603

R806

R500
W045

W043
W044

R613 W031 C1008


W066

S102B
R615 W030 W813
R617

CP802B CP801
Q105
W028

C633 S501A
R616

IC199
W029

W027
R112
R113

Q607 R1007

R121
W808 C123
R110
R109

W042

CD101A W026
C614 J1001
W041

C118 CD101B D106_1


J703 J702 OS101
C612 SW101 SW102 SW103 SW104 SW105
W060
W811

R701

F-1 F-2
PRINTED CIRCUIT BOARDS
MAIN/CRT (CHIP MONUTED PARTS)
SOLDER SIDE

T
R704
R128

R126
R101

C101
C112

R143
R115

R618
R107
R1003
R1008

C629
R610

R1005

R1004
R609 C627
C626

R627
C1004_2

R124_1
41

R106
R108
R105
25
C609

1
10
64

IC
R116

C604
C603
1

R125
R127
C102 C104

C108_1
C105
R102
C107
R129

R103
R104

B_SHORT
B_SHORT
C501_2
R420

R419

R003
R004

C001

F-3 F-4
A B C D E F G H

0 0 0 0 MICON/CHROMA/TUNER SCHEMATIC DIAGRAM


1 2 3 4
(MAIN PCB)

VSS
E1

E2
E0
S-24C02BDP-1A
8 8

MEMORY IC

50V 10 KA
IC199
H.CTL

C633
Q607

MODE
VCC

SDA
SCL
KTC3198
R621 6.0 5.0

47K 1/4W
8 7 6 5
4.9 0 4.8 4.8

R617
220 1/4W

1/2W
5.6

R620

W808
R618

2.2K

P.CON+5V
P.CON+5V

W823
22K

H_OUT

H_CTL
W828
3 FROM/TO DEFLECTION/CRT

H_SYNC
R608

B.OUT
ABCL
H_CTL

G.OUT

R.OUT
7 C118 CLAMP 7
2 1K 1/4W
R110 10K 1/4W P.CON+B
6.3V 100 KA C101
V_OUT
R109 10K 1/4W

1K 1/4W 11E1-EIC
D606
0.01 F

100 1/4W

100 1/4W

100 1/4W
C630 GND

50V 1 KA C627 10K


R610
V_FEEDBACK
AT+5V

1 MKT
10V 470 YK

CH

10K 1/4W

0.01 F
ABCL

0.01 F
C626
R611

C624_1
C112
H_OUT

R105
R124_1

4.7K

100P

R609

120K
R614
10K C629

R615

R613
X-RAY

63V
C628
R616
1 CNVSS 41 NC SDA
R130 0.01 F R.OUT

R107

100
R106

R108

100
2 XIN 42 HVCO F/B

4.7K
SCL G.OUT

R627

10K
10K 1/4W 5 6 7
3 XOUT 43 AFC FILTER C623
NC NC B.OUT
4 TEST1 44 DEF GND 0 0 0 0 0 0 4.8 0 4.8 0 4.8 0.7 2.3 2.2 2.3 8.0 0 8.0 2.0 1.0 0 3.4 3.7 0
H_SYNC
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 50V 2.2 KA

7.9
5 VSS 45 FBP IN
6 R119 4.8
8.6
R607
8V REG 6
6 MCU VCC 46 H OUT Q606

65

40
KTC3203_Y
7 TEST0 47 DEF VCC 100 1/4W

8.5
22K 1/4W 2.4 4.7 FROM/TO TV POWER
AFT MCU GND 4

11.3
66

39
8 FILT 48 NC R112 Ver.Proc. UNREG+12V
9 HLT 49 HI VCC 4.9 3.6 AT+5V
2.2K 1/4W KEY1 IIC BUS PGB OUTPUT Stage Hor.Proc. Ver SYNC SEP V_OUT

67

38
10 VHOLD 50 R OUT R113 DECODER DRIVE SYNC SEPA/Hor.VCO POWER_FAIL
Ver.COUNT DOWN 2.6
4.9 CUT-OFF Hor.COUNT DOWN R606
11 CVIN 51 G OUT 2.2K 1/4W KEY2 SDA/SCL AFC-1/H COINCIDENT V RAMP V_FEEDBACK UNREG+12V

68

37
R116 ROM HV BLK
12 RESET IN 52 B OUT RAM OSD AFC-2 H PHASE 0 22K 1/4W X-RAY
4.9
POWER_ON GND

69

36
13 MCU RESET OUT 53 ACL 2.2K R115
3.2 C622 C621
14 Y SW OUT 54 NC 4.8
22K REMOCON

70

35
15 V/C GND 55 PROTECT
0 I/O 3.5 50V 1 KA 16V 47 YK
16 3.58 XTAL 56 SDA NC AUDIO_OUT C620_1 FROM/TO SOUND/AV

71

34
RGB Proc.2
17 C-APC 57 H_CTL OSD SW RGB Proc.1 0.7
5 4.9 1 0.01 B AUDIO_MUTE 5
72 RGB MATRIX

33
18 MCU5.7V REG OUT 58 SCL NC CONTRAST NC
COLOR CONT VIDEO_IN
P-ON CONT Power Manage. BRIGHTNESS 2.8
19 NC 59 NC 4.9 IIC D604
AUDIO_MUTE D603 AUDIO_IN
73

32
MCU RESET NC
20 CVBS IN3 60 NC
TIM 8.7 AUDIO_OUT
2.8 1SS133 MTZJ8.2B R605
21 AUDIO IN3 61 NC X-RAY CCD
74

31
R125 INT Chroma Proc. P.CON+5V
22 V/C VCC 62 DEGAUSS_H Vldeo Proc. P.CON+5V 220 1/2W
R127 4.8 ACC/C-BPF 1.9
47K IIC_OFF C-TRAP/YDELAY GND
75

30
23 MCU TEST 63 STANDBY_H PWM APC/KILLER TUNER+5V
SHARPNESS
24 CVBS IN2 64 VOLUME 1K 0 CLK CONT MCU TINT/DEMO 2.2
ON_TIMER AD CPU core BLACK STRETCH
5V REG
76

29
25 AUDIO IN2 65 NC CLK Y MUTE Q602 4.9
0 5.5 R604
26 CVBS IN1 66 AFT KTC3203_Y
77

28
NC LPF
27 AUDIO IN1 67 KEY1 6bB AMP ATT C614 100 1/4W 5.5
4.8 2.2 7.2 R629
POWER_FAIL AUDIO_IN
78

27
28 5.7V REG OUT 68 KEY2 C617
VCO 1.9 50V 1 KA
29 C(Y/C) IN 69 POWER_ON R129 0 XO 22 3W
VIDEO_IN 10V 100 YK 7.2
79

26
4 30 Y(Y/C) IN 70 REMOCON
47K C612 5.5 4
4.9 VCXO 0
31 VREG VCC 71 AV2 50V 1 KA 5V REG
80

25

19

18
NC NC 4.9 C001
Q603
32 FSC OUT 72 AV1 1 NC
KTC3203_Y
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 0.01 F
33 MONITOR OUT 73 AUDIO_MUTE C002
0 0 4.9 4.9 0 4.9 0 1.0 1.9 0.3 2.7 4.9 4.9 2.7 0 3.3 2.8 5.5 0 2.5 2.2 4.9 0 1.9 2 NC
34 AUDIO ATT OUT 74 X-RAY MICON/CHROMA IC

3.579545MHz
NC L001

F 22P CH 100CT3R505
IC101 6.3V 1000 YK

100 1/4W
F
50V 1 KA

TUNER+5V
B C108_1 0.001 B
35 AUDIO ATT FILTER 75 IIC_OFF
0.01 F

C602

X601
OEC7091B

R602
C104

C102

0.1
36 TEST 3 76 ON_TIMER AT+5V W833 3.3uH 0305
R103 C106

C615

10V 100 YK
37 V RAMP F/B 77 SYNC 0.01 F 4 NC

50V 1 KA
C601
TU_VIDEO

C606
38 V RAMP OUT 78 POWER FAIL

C603
50V 1 KA
R102

1K

5 NC
1K

39 V RAMP CAP 79 NC
C609 D602
16V 47 YK
C103
W809

40 8.7V REG OUT 80 EXT_MUTE 6 NC


C107
B

1M

0.01 F
R104

C604
220P

MTZJ9.1B
C105
470P

C610

0.022
3 C616 3

8.2K 50V 1 KA
6.3V 47 KA TU_AUDIO

C605
7 NC
50V 1 KA
W816

5.1 8 NC

1/4W
R601
0 ON_TIMER
SWITCHING 9 NC
4.8 Q105 TEST POINT
R004
KRA102MAT SCL
10
REMOCON

POWER_ON

CP601
KEY1
KEY2

100
AT+5V

R003 00_8283_0611_00_000
11 SDA
100 NC 6
12 AFT NC 5
25V 10 KA

IIC_OFF
R143 IIC_OFF 4
1/4W

13 TU_AUDIO SDA
SDA 3
R121

47

0.022 B
SCL

C007
2 R128 SCL 2 2
270

5.5 14 NC
GND 1
560 R002 R001
P.CON+B
C123

4.9 8.8 R603 15


POWER ON/ON TIMER

R126 R101 15K 1/2W 15K 1/2W

0.022 F
120 1/2W

C004
SLR-342VCT32

2.7K 560 5V REG 16 NC


D106_1

4.9

4.8

VOL DOWN

TU001
EVQ21505R

EVQ21505R

EVQ21505R
0

Q601
EVQ21505R

EVQ21505R
CH DOWN

TU_VIDEO
SW101

SW103

SW104

POWER
VOL UP

ENG36A01GR
SW102

SW105
CH UP

KTC3203_Y 17

MTZJ33B
B+ 3
GND 2
1

D001
Vout

20

21
PCB010
TMC558

OS101
RPM7138-WH5
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED CAUTION:SINCE THESE PARTS MARKED BY ARE ATTENTION:LES PIECES REPAREES PAR UN ETANT CAUTION: DIGITAL TRANSISTOR R.SIGNAL
1 NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST CRITICAL FOR SAFETY,USE ONES DANGEREUSES AN POINT DE VUE SECURITE G.SIGNAL 1
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES B.SIGNAL
DEFLECTION SIGNAL
TUNER VIDEO SIGNAL
A B C D E F G H
G-1 G-2
A B C D E F G H

TV POWER SCHEMATIC DIAGRAM


(MAIN PCB)
8 8

CAUTION :FOR CONTINUED PROTECTION AGAINST FIRE HAZARD,


REPLACE ONLY WITH THE SAME TYPE 4A 125V (F501)
FUSE.

4A 125V ATTENTION :POUR UNE PROTECTION CONTINUE LES RISQUES


D’INCEIE N’UTILISER QUE DES FUSIBLE DE MEME
TYPE 4A 125V (F501).

TO SOUND/AV

GND
R517_1
D505
SOUND+B
7 21DQ09N 1 1W 7

16V 1000 YK
C518

C519
500V 470P B

SOUND_GND

FROM/TO DEFLECTION/CRT
D510

+-10%
+B

2.7M 1/2W
DEGAUSS COIL
RU2AM-EIC UNREG+12V
L503

R500
PROTECT DRIVE
8R140032 CP502 W802 Q503
A1561WV2-2P 2SA1624
W834

160V 100 MHE


135.0 0
1 P.CON+B
1

6 2
2

100V 10 MHE
C521
135.0

C507
TH501_1
R501 R514
1 C517
B59203-S1060-B14 R523 R527
CP503
5.6 5W 0.22 1W 2KV 820P RR

1N4005-EIC
003P-2100 47K 5.6K

1N4005-EIC

D502
D501
R525

1/2W
R510_1
1.5 2W

3.3M
GND

B
275V 0.22 ECQUL

1N4005-EIC
1.5M 1/2W

1/4W
500V 0.001
1N4005-EIC

200V 220 YK
C503
500V 0.001 B

D503

R528
MTZJ18B
FROM/TO MICON/CHROMA/TUNER

C526_1
C505

C502
R538

D504
3 4 T502

D509
5 4A 125V 5

6.8K
81291084
W832
F501 1 2 POWER_FAIL
51MS040L
D521 0 R537
D516 R504 R505 4.9
COIL,LINE FILTER 1.7 10.0 X-RAY
4A125V 8 11 P.FAIL 22K 1/4W
FH501 FH502 L501 1N4937 100 1/4W 1K 1/4W Q505

50V 1 YK
EYF-52BCY EYF-52BCY 1R5A102F20 MTZJ6.8B 4.8
0

C516

1/4W
KTA1266
NC 7 12

R516
B504

10K
144.0 132.3 D513
6 13 UNREG+12V
W5RH3.5X5X1.0

16V 2200 YK
W5RH3.5X5X1.0 21DQ09N
0
B501

AC120V_60Hz NC 5 14 AT+5V

C515
S501A

CD501
0R414903 10.3 0
4 15 GND
4 BLACK 4
W819

6.6 11.3
2KV 820P RR

C506 3 16
C514_1
BLADE
WIDE

S501B

WHITE
250V 0.001 KX 10.3
144.0
2 17 NC
D R508
C509
G 4.8

100 1/4W 1SS133


D512
220 1W 0.047 M 18 NC
1SS133

S
D508

0.1 POWER AMP

1SS133
Q501

D515
12K 1/4W

R503

STP5NC50FP
R520

220 1/4W
R509
W830

W810
C511
2.7K 1/4W

3 3
R506

BUFFER
MTZJ18B

50V 1 KA
Q502
D506

KTC3198
0.68 1W

100 1/4W
R542

4.8 0.1

R502
0.0082 B
C501_2

HS501
0
763WSAA013

120K 1/2W
C513_1

CH
1SS133
C508

D511

R515
0.001
250V 0.0047 KX
C510 9.5 6.0

1SS133

1SS133
D514

D522
0.1 F
FEED BACK FEED BACK

2.2K 1/4W
5.5
IC501 SWITCHING

R513
LTV-817M-VB Q507
KTC3198
2 11.5 10.5 2
R512 R519
4

680 1/4W

1/4W
1.2K 1/4W
3

R507
0.1 9.5

27
MTZJ5.6B
D528

5.6K +-1%
R518
PCB010
TMC558

1 1
NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR.
THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
CAUTION:SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
ARE ATTENTION:LES PIECES REPAREES PAR UN ETANT
DANGEREUSES AN POINT DE VUE SECURITE
IS NON POLAR ONE. WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES

A B C D E F G H
G-3 G-4
A B C D E F G H

FROM MICON/CHROMA/TUNER DEFLECTION/CRT SCHEMATIC DIAGRAM (MAIN PCB) CP802A B2013H02-5P


GND
GND 1
CD802
0
1
CP802B
GND
B2013H02-5P
GND
CLAMP CLAMP
CLAMP CLAMP 2 2 CLAMP
G.OUT G.OUT
8 G.OUT G.OUT 3 3 G.OUT 8
R.OUT R.OUT
R.OUT R.OUT 4 4 R.OUT
B.OUT B.OUT
B.OUT B.OUT 5 5 B.OUT
V-OUT IC IC401 LA78040N-E CD803
CP803A B2013H02-4P 0 CP803B B2013H02-4P
HEATER HEATER
THERMAL HEATER 1 1 HEATER
PROTECTION GND GND
GND 2 2 GND
PUMP
UP AMP NC NC 3 3 NC NC
180V 180V
180V 4 4 180V

4.7K 1/4W
4.7K 1/4W

4.7K 1/4W
R811

R814
R809
1 2 3 4 5 6 7 CP801 RED OUT GREEN OUT BLUE OUT
CD801_1 Q801 Q802 Q803
3.5 25.0 2.0 0 12.0 25.0 3.5 TBS-X01X-A1
0 2SC1473A 2SC1473A 2SC1473A

YK
35V 100
C414
1 1 3.2 3.2 3.2
7 100.6 98.4 95.4 7

220uH
L801
8
R423 2.7 2.7 2.7
12 V801
D403
100 1/4W
13 A34AGT13X98(L)
R424
11E1-EIC

MKT

330 1/2W
100V 0.15
470 1/4W

C422

R410
9
10
R418 R420 R

330P B

330 1/4W
8

330 1/4W

330P B

330 1/4W
330P B
G

C808

R813
25V 470 YK
10K 1/4W

R815

R816
6

470
R419

C809

C810
22K 1/4W 2.7K R415

1 1/2W
35V 22 YK
B

C418

R416
11

R417
1.8K 1/2W 5 7 1

C417_2

50V 10 YK
2.2K 1/2W
TO DY

R413
2.2 1/2W

C427
HS401

R422
6 763WSAA013 6
5 CP401 14 15 16
A1561WV2-A5P
4
3 TP022 TP024 TP023

100V 22 YK
C434
R429 NC 2
1
4.7 1W

2.7K 1/4W

2.7K 1/4W
10K +-1%

2.7K 1/4W

1W

1W
MTZJ5.1B

15K 1W
D411
D412

R408

15K

15K
AU02A-EIC
FROM/TO MICON//CHROMA/TUNER

R803_1

R805_1

R807_1
R804

R806
R802
R401 R409
W831
5 X-RAY 5
27K +-1% 27K +-1%

250V 0.47 PMS

YK
P.CON+B

C401_1
C437

4.7mH 250V 4.7


T401 L401
9 ETH09K14BZ
3 4 150 1/2W
R404

NC 2
470 1/2W
R446

1 6
GND
H.DRIVE
V_FEEDBACK
Q402 10
4 V_OUT 2SC1627_Y 4
ABCL 27.0 FB401 FNI14B002_M
0.001 CH

11
C410_1
MMTS

H_OUT 130.0 COL


0.3 1 HV
MPP

H_SYNC FOCUS
50V 22 YK

0
1K 1/4W

130.0
C440

CP806
R405

C446
100V 0.01

1.25KV 0.0086

H.OUTPUT SCREEN
C443

FOCUS
100 1/4W

0 Q401 132.5 VIDEO F


FROM/TO TV POWER 6
0
R427

TT2140LS-YBC11

2KV 0.001 B
SCREEN

C819_1
132.5 B+ S
GND 2
HS402 GND 0
11
TP401 763WSAA017 48.0 AFC
9
HEA ABL 4.3 96.4
B_SHORT 7.0 7
10 TER
+B

9
8
3 0 GND 3
R403 8

7
E12 101.6
10K 1/4W 4 GND 0

F
6
8
C406 0
P.CON+B 25.0 E25
3

1
NC

5
E8
500V 150P B 5 0 0

4
3
6.4 99.6 J801
ISMS01S
MTZJ6.2B
D404

AU02A-EIC
D405

R447
D406
UNREG+12V PCB110
820P RR

150 2W 11E1-EIC
TCC417
C420_1
AU02A-EIC

2 2
D410
11E1-EIC

2KV
D409

R449
ATTENTION:LES PIECES REPAREES PAR UN ETANT R.SIGNAL
560 1/2W
DANGEREUSES AN POINT DE VUE SECURITE
N’UTILISER QUE CELLS DECRITES G.SIGNAL
R448 DANS LA NOMENCLATURE DES PIECES
B.SIGNAL
560 1/2W
R445
DEFLECTION SIGNAL
CAUTION:SINCE
MHE

180K 1/4W THESE PARTS MARKED BY ARE


35V 470 YK

250V 22 YK

CRITICAL FOR SAFETY,USE ONES NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
C448_1

C435

220K 1/4W

DESCRIBED IN PARTS LIST ONLY


C403

11E1-EIC
100V 0.1

OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE


D408

1 1
R421

PCB010 NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR.
TMC558 WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. IS NON POLAR ONE.

A B C D E F G H
G-5 G-6
A B C D E F G H

SOUND/AV SCHEMATIC DIAGRAM


8
(MAIN PCB) 8

RCA JACK WHITE


TO MICON/CHROMA/TUNER
J703
(FRONT)
AV1-09D-4 ACCESSORY
19 R703

E
AUDIO 2 W811
7 AUDIO_IN A_IN 7

1
820
UM-4
20 BT001
R704

E
VIDEO 2 V_IN
VIDEO_IN R03(AB)E_2P_G

1
10

68 1/4W
R701

R702

47K
RCA JACK YELLOW
TM101 UM-4
J702
RC-EH050(CT-859) BT002
GND
R03(AB)E_2P_G
AV1-09D-3

6 6

EAR PHONE_JACK
5 J1001 5
MSJ-035-12A_PC
2
R1007 3
1
10 1/2W

KA
C1008

16V 47
4 4

18
FROM TV POWER
CD101A SPEAKER
SOUND_GND
CH012002
1 1
SOUND+B 2 2
CD101B
CH012003 SP1001
GND S08F21
8.2 3.5 0 3.4
8 OHM
5 6 7 8

AN7511
SOUND AMP IC
+ -
3 3

IC1001
FROM MICON/CHROMA/TUNER
4 3 2 1

W813
R1001 5.1 0 0.3 3.9
AUDIO_MUTE
47K 1/4W

R1003
P.CON+5V
68K

25V 10 KA
KA
C1003
R1004

C1005
R1005
100K

B
270K
W803

C1004_2
2 2

0.0015
50V

R1008

68K
C1001 17
AUDIO_OUT
50V 0.1 KA PCB010
TMC558

NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED


1 WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
CAUTION:SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
ARE ATTENTION:LES PIECES REPAREES PAR UN ETANT
DANGEREUSES AN POINT DE VUE SECURITE
TUNER VIDEO SIGNAL 1
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. DESCRIBED IN PARTS LIST ONLY N’UTILISER QUE CELLS DECRITES AUDIO SIGNAL
DANS LA NOMENCLATURE DES PIECES

A B C D E F G H
G-7 G-8
WAVEFORMS
MICON/CHROMA/TUNER

1 0.5V 2ms/div 6 1V 20µs/div 11 200V 20µs/div

2 20V 20µs/div 7 1V 20µs/div 12 10V 5ms/div


DEFLECTION/CRT

3 200mV 20µs/div 8 0.5V 5ms/div 13 10V 5ms/div

4 0.5V 5ms/div 9 20V 20µs/div 14 50V 20µs/div

5 1V 20µs/div 10 2V 20µs/div 15 50V 20µs/div


NOTE: The following waveforms were measured at the point of the corresponding
balloon number in the schematic diagram.
H-1
WAVEFORMS

16 50V 20µs/div
SOUND/AV

17 0.5V 1ms/div

18 1V 1ms/div

19 200mV 500µs/div

20 500mV 20µs/div
NOTE: The following waveforms were measured at the point of the corresponding
balloon number in the schematic diagram.
H-2
MECHANICAL EXPLODED VIEW
202
107

202
202

202

104

201
102

111 202

111 201 PCB110


110 103
201 (CRT PCB ASS'Y)

111 205

201 204
106
111
203

106

106
101D 108 PCB010
105
(MAIN PCB ASS'Y)

101B
207

101C

206

109

101A
101
I-1
MECHANICAL EXPLODED VIEW
(PACKING DIAGRAM)

118, 119, 120,


TM101 114
114

114

113

116

115

112

115

115

115

I-2
MECHANICAL REPLACEMENT PARTS LIST
Location No. TSB P/N Reference No. Description

101 AE003318 A3M127G720 CABINET,FRONT ASSY


101A AE004096 701WPJC674 CABINET,FRONT
101B AE004097 713WPAA147 GLASS,LED
101C AE004098 713WPAA146 GUIDE,REMOCON
101D AE004099 735WPBB102 BUTTON,FRAME

102 AE003321 A3M127G740 CABINET,BACK ASSY

103 BZ710260 899HV3T000 HOLDER,ANODE WIRE


104 AE000006 7220001119 SHEET,CSA WARNING
105 AE000091 722000A023 SHEET,HWC
106 AE000535 800WQ0A024 FELT SHEET
107 AE003322 722549A322 SHEET,RATING
108 AD300132 7230006818 SHEET,CAUTION
109 AD300808 735WPA0396 SPEAKER HOLDER

110 AD300759 741WUA0021 SPRING,EARTH


111 AE000053 800WR0A011 SHEET,CRT SUPPORT (D)
112 AE003323 723000C490 SHEET,BAR CODE
113 AE000093 791WHA0090 LAMIFILM,BAG
114 AD300809 792WHAA052 PACKAGE,TOP
115 AD300810 792WHAA053 PACKAGE,BOTTOM
116 AE003324 793WCDC102 GIFT BOX
117 AE003325 A3M127G975 INSTRUCTION BOOK KIT
118 AD302406 JB5UD200 POLYBAG,INSTRUCTION(RED CAUTION)
119 AD300022 J3I70417 REGISTRATION CARD

120 AE003326 J3M12701A INSTRUCTION BOOK

201 BZ710275 8121J50B54 SCREW,TAP TITE(P) GW20 5x28


202 BZ710035 8117540A64 SCREW,TAPPING(B0) TRUSS 4x16
203 BZ710018 8107630804 SCREW,TAP TITE(S) BRAZIER 3x8
204 BZ710352 8109I30604 SCREW,TAP TITE(B) WH7 3x6
205 BZ710562 8109I30804 SCREW,TAP TITE(B) WH7 3x8
206 BZ710031 8110630A04 SCREW,TAP TITE(P) BRAZIER 3x10
207 BZ710030 8110630804 SCREW,TAP TITE(P) BRAZIER 3x8

J1-1
ELECTRICAL REPLACEMENT PARTS LIST
Location No. TSB P/N Reference No. Description
RESISTORS
! R401 BZ210089 R4X5T6273F R,METAL 27K OHM 1/6W
! R404 AE004065 R615U2151J R,FUSE 150 OHM 1/2W
! R408 BZ210092 R4X5T6103F R,METAL 10K OHM 1/6W
! R409 BZ210089 R4X5T6273F R,METAL 27K OHM 1/6W
! R429 AD301700 R635814R7J R,FUSE 4.7 OHM 1W
! R447 BZ210229 R3X28A151J R.METAL OXIDE 150 OHM 2W
! R500 BZ210080 R0G3K2275K RC 2.7M OHM 1/2W
! R501 AD300782 R5Y2CD5R6J R,CEMENT 5.6 OHM 5W
! R508 AD300783 R3X181221J R,METAL OXIDE 220 OHM 1W
! R509 BZ210135 R002T4221J RC 220 OHM 1/4W
R510 AE003327 R00202335J RC 3.3M OHM 1/2W
! R514 BZ210190 R63581R22J R,FUSE 0.22 OHM 1W
! R515 BZ210081 R002T2124J RC 120K OHM 1/2W
! R517 BZ210039 R3X181010J R,METAL OXIDE 1 OHM 1W
! R518 AD300036 R4X5T6562F R,METAL 5.6K OHM 1/6W
! R519 BZ210124 R002T4122J RC 1.2K OHM 1/4W
! R525 BZ210097 R3X18A1R5J R,METAL OXIDE 1.5 OHM 2W
! R538 BZ210206 R002T2155J RC 1.5M OHM 1/2W
! R542 BZ210058 R3X181R68J R,METAL OXIDE 0.68 OHM 1W
! R629 AE000081 R3X28B220J R.METAL 22 OHM 3W
! R803 BZ210099 R3X181153J R,METAL OXIDE 15K OHM 1W
! R805 BZ210099 R3X181153J R,METAL OXIDE 15K OHM 1W
! R807 BZ210099 R3X181153J R,METAL OXIDE 15K OHM 1W
CAPACITORS
! C403 BZ110149 E02LT4471M CE 470 UF 35V
! C414 AD301434 E02LU4101M CE 100 UF 35V
! C418 BZ110041 E02LT3471M CE 470 UF 25V
C420 BZ110203 C0PLRR7W2K CC 820 PF 2KV RR
! C434 BZ110195 E02LU8220M CE 22 UF 100V
C437 BZ210173 P4J7F3474J CMPP 0.47 UF 250V PMS
! C443 BZ110258 P4N8FJ862H CMPP 0.0086UF 1.25KV
! C446 BZ110205 E02LU5220M CE 22 UF 50V
! C448 BZ110204 E0ELFD220M CE 22 UF 250V
! C503 BZ110061 C0JTB0513K CC 0.001 UF 500V B
! C505 BZ110025 P2122B224M CMP 0.22 UF 275V ECQUL
! C506 AD301026 CD39E0M13M CC 0.001 UF 250V
! C508 AE002878 CD39E0MQ3M CC 0.0047UF 250V
C514 BZ110203 C0PLRR7W2K CC 820 PF 2KV RR
! C515 BZ110135 E02L02222M CE 2200 UF 16V
C517 BZ110203 C0PLRR7W2K CC 820 PF 2KV RR
! C519 AD300925 E02LT2102M CE 1000 UF 16V
C521 BZ110092 E5EZFB101M CE 100 UF 160V
! C526 BZ110089 E02LFC221M CE 220 UF 200V
C615 AE003280 E52H05010M CE 1 UF 50V
C819 BZ110247 C0JBB0713K CC 0.001 UF 2KV B
DIODES
D001 BZ410037 D97U03301B DIODE,ZENER MTZJ33B T-77
D106 BZ410054 0021721150 LED SLR-342VCT32
D403 BZ410043 D2WT011E10 DIODE,SILICON 11E1-EIC
D404 BZ410066 D97U06R21B DIODE,ZENER MTZJ6.2B T-77
! D405 BZ410063 D2WTAU02A0 DIODE,SILICON AU02A-EIC
D406 BZ410043 D2WT011E10 DIODE,SILICON 11E1-EIC
D408 BZ410043 D2WT011E10 DIODE,SILICON 11E1-EIC
D409 BZ410043 D2WT011E10 DIODE,SILICON 11E1-EIC
! D410 BZ410063 D2WTAU02A0 DIODE,SILICON AU02A-EIC
! D411 BZ410063 D2WTAU02A0 DIODE,SILICON AU02A-EIC
! D412 BZ410020 D97U05R11B DIODE,ZENER MTZJ5.1B T-77
! D501 BZ410085 D2WXN40050 DIODE,SILICON 1N4005-EIC
! D502 BZ410085 D2WXN40050 DIODE,SILICON 1N4005-EIC
! D503 BZ410085 D2WXN40050 DIODE,SILICON 1N4005-EIC
! D504 BZ410085 D2WXN40050 DIODE,SILICON 1N4005-EIC
! D505 BZ410010 D28T21DQN9 DIODE,SCHOTTKY 21DQ09N-TA2B1
D506 AD300671 D97U01801B DIODE,ZENER MTZJ18B T-77
D508 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
! D509 AD300671 D97U01801B DIODE,ZENER MTZJ18B T-77
! D510 BZ410080 D2WXRU2AM0 DIODE,SILICON RU2AM-EIC
D511 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
! D512 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
D513 BZ410010 D28T21DQN9 DIODE,SCHOTTKY 21DQ09N-TA2B1
D514 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
D515 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77

J2-1
ELECTRICAL REPLACEMENT PARTS LIST
Location No. TSB P/N Reference No. Description
DIODES
! D516 AD300731 D2WXN49370 DIODE,SILICON 1N4937
D521 BZ410022 D97U06R81B DIODE,ZENER MTZJ6.8B T-77
D522 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
D528 BZ410021 D97U05R61B DIODE,ZENER MTZJ5.6B T-77
D602 BZ410023 D97U09R11B DIODE,ZENER MTZJ9.1B T-77
D603 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77
D604 BZ410058 D97U08R21B DIODE,ZENER MTZJ8.2B T-77
D606 BZ410043 D2WT011E10 DIODE,SILICON 11E1-EIC
ICS
IC101 AE002802 I56F07091B IC OEC7091B
IC199 AD302160 A3M105A015 IC S-24C02BDP-1A
! IC401 AE002783 I03TD804N0 IC LA78040N-E
! IC501 BZ410088 0002E00610 PHOTO COUPLER LTV-817M-VB
IC1001 BZ611001 I01DP75110 IC AN7511
TRANSISTORS
Q105 BZ510086 TPATB03003 COMPOUND TRANSISTOR KRA102MAT
! Q401 AD301779 TD3Q021400 TRANSISTOR,SILICON TT2140LS-YBC11
! Q402 BZ510089 TC5T01627Y TRANSISTOR,SILICON 2SC1627_Y(TPE2)
! Q501 BZ510093 TJXG5NC500 FET STP5NC50FP
! Q502 BZ510069 TCATC31980 TRANSISTOR,SILICON KTC3198-AT(Y,GR)
Q503 BZ510004 TA3T016240 TRANSISTOR,SILICON 2SA1624-AA
Q505 BZ510073 TAATA12660 TRANSISTOR,SILICON KTA1266-AT(Y,GR)
Q507 BZ510069 TCATC31980 TRANSISTOR,SILICON KTC3198-AT(Y,GR)
Q601 BZ510070 TCAT032034 TRANSISTOR,SILICON KTC3203_Y-AT
Q602 BZ510070 TCAT032034 TRANSISTOR,SILICON KTC3203_Y-AT
Q603 BZ510070 TCAT032034 TRANSISTOR,SILICON KTC3203_Y-AT
Q606 BZ510070 TCAT032034 TRANSISTOR,SILICON KTC3203_Y-AT
Q607 BZ510069 TCATC31980 TRANSISTOR,SILICON KTC3198-AT(Y,GR)
! Q801 AD300794 TCKT1473A0 TRANSISTOR,SILICON 2SC1473A-TA-(RQ)
! Q802 AD300794 TCKT1473A0 TRANSISTOR,SILICON 2SC1473A-TA-(RQ)
! Q803 AD300794 TCKT1473A0 TRANSISTOR,SILICON 2SC1473A-TA-(RQ)
COILS &TRANSFORMERS
L001 AE000290 02167F3R3J COIL 3.3 UH
L401 AD301644 021L75472J COIL 4.7 MH
! L501 AD300677 029T00A7M1 COIL,LINE FILTER 1R5A102F20
! L503 AD302161 028R140032 COIL,DEGAUSS 8R140032
L801 BZ310113 021673221K COIL 220 UH
T401 BZ310157 045009003J TRANS,HORIZONTAL DRIVE ETH09K14BZ
! T502 AD302162 0481291084 TRANSFORMER,SWITCHING 81291084
JACKS
J702 AD300680 060Q401077 RCA JACK AV1-09D-3
J703 AD300681 060Q401076 RCA JACK AV1-09D-4
! J801 AD301147 066F120018 SOCKET,CATHODE RAY TUBE ISMS01S
J1001 AD302163 060J121014 JACK,RCA,3.5 MSJ-035-12A_PC
SWITCHES
SW101 BZ612010 0504101T34 SWITCH,TACT EVQ21505R
SW102 BZ612010 0504101T34 SWITCH,TACT EVQ21505R
SW103 BZ612010 0504101T34 SWITCH,TACT EVQ21505R
SW104 BZ612010 0504101T34 SWITCH,TACT EVQ21505R
SW105 BZ612010 0504101T34 SWITCH,TACT EVQ21505R
P.C.BOARD ASSEMBLIES
PCB010 AE003328 A3M127G010 PCB ASS'Y TMC558A
PCB110 AE003329 A3M127G110 PCB ASS'Y TCC417A
MISCELLANEOUS
B501 BZ310121 024HT03553 CORE,BEADS W5RH3.5X5X1.0
B504 BZ310121 024HT03553 CORE,BEADS W5RH3.5X5X1.0
BT001 AE000012 1412004008 BATTERY,MANGAN R03(AB)E_2P_G
BT002 AE000012 1412004008 BATTERY,MANGAN R03(AB)E_2P_G
! CD501 AD300685 120R414903 CORD,AC BUSH 0R414903
! CP401 BZ614303 069S450089 CONNECTOR PCB SIDE A1561WV2-A5P
! CP502 AD300687 069S420110 CONNECTOR PCB SIDE A1561WV2-2P
CP503 BZ614016 069W01001A CONNECTOR PCB SIDE 003P-2100
CP601 AD301329 069E260659 CONNECTOR PCB SIDE 00_8283_0611_00_00
CP801 AD300800 069W010030 CONNECTOR PCB SIDE TBS-X01X-A1
CD101A AD301330 06CH012002 CORD,CONNECTOR CH012002
CD101B AD301331 06CH012003 CORD,CONNECTOR CH012003
CP802A BZ614276 067U005049 WIRE HOLDER B2013H02-5P
CP802B BZ614276 067U005049 WIRE HOLDER B2013H02-5P
CP803A BZ614334 067U004029 WIRE HOLDER B2013H02-4P
CP803B BZ614334 067U004029 WIRE HOLDER B2013H02-4P
EL001 BZ614043 124116281A EYE LET XRY16X28BD

J2-2
ELECTRICAL REPLACEMENT PARTS LIST
Location No. TSB P/N Reference No. Description
MISCELLANEOUS
EL002 BZ614044 124120301A EYE LET XRY20X30BD
! F501 AD302166 081PC04005 FUSE 51MS040L
! FB401 AE003330 043214050F TRANSFORMER,FLYBACK FNI14B002_M
FH501 AE002634 06710T0009 HOLDER,FUSE EYF-52BCY
FH502 AE002634 06710T0009 HOLDER,FUSE EYF-52BCY
OS101 AD301048 0773071001 REMOTE RECEIVER RPM7138-WH5
S101 AD302168 WBL6026038 FLAT CABLE AWM2468 A WG26 4C BLACK 260MM
S102 BZ614371 WCL6834038 FLAT CABLE AWM2468 A WG26 5C GRAY 340MM
SP1001 AD300689 070Y132018 SPEAKER S08F21
! TH501 AD302000 D8EE0B1400 DEGAUSS ELEMENT B59203-S1060-B14
TM101 AE003331 076N0EH050 TRANSMITTER RC-EH050(CT-859)
! TU001 AE001528 0163100007 RF UNIT ENG36A01GR
! V801 BZ614141 098Q1404B2 CRT W/DY A34AGT13X98(L)
X601 AD302003 100CT3R505 CRYSTAL HC-49/C

RESISTOR
RC................... CARBON RESISTOR

CAPACITORS
CC................... CERAMIC CAPACITOR
CE................... ALUMI ELECTROLYTIC CAPACITOR
CP................... POLYESTER CAPACITOR
CPP.................. POLYPROPYLENE CAPACITOR
CPL.................. PLASTIC CAPACITOR
CMP....................... METAL POLYESTER CAPACITOR
CMPL................ METAL PLASTIC CAPACITOR
CMPP................ METAL POLYPROPYLENE CAPACITOR

J2-3
TOSHIBA CORPORATION
1-1, SHIBAURA 1-CHOME, MINATO-KU, TOKYO 105-8001, JAPAN

Вам также может понравиться