Академический Документы
Профессиональный Документы
Культура Документы
PanelDraw
User
Manual 2012
Author: Abhishek Bansal Rev – 02
Revision Sheet
Revision Sheet
USER'S MANUAL
Table of Contents
1.0 GENERAL INFORMATION .................................................................................................... 1
1.1 System Overview ................................................................................................................... 1
1.2 Authorized Use Permission.................................................................................................... 1
1.3 Points of Contact ................................................................................................................... 2
1.3.1 Information ..................................................................................................................................... 2
2.0 GETTING STARTED ................................................................................................................ 3
2.1 Downloading PanelDraw.ZIP from web ............................................................................... 3
2.2 Extracting from the .ZIP archive .......................................................................................... 3
2.3 Running the Application........................................................................................................ 3
3.0 USER INPUT FORMS .............................................................................................................. 4
3.1 Form 1: System Data............................................................................................................. 4
3.2 Form 2: Individual Feeder Details ........................................................................................ 7
3.3 Form 3: Incomer / Contactor Ratings ................................................................................... 9
3.4 Form 4: Incomer Types and Metering Required ................................................................ 11
3.5 Form 5: Suggested Panel GA .............................................................................................. 13
3.6 Output Drawing Files Save As Dialog Box ......................................................................... 14
PanelDraw application is intended to assist in electrical cabinet design and drawings preparation.
This is done by taking input from the user through Form interaction, parsing the information for
drawing sheets generation and finally actually generating the drawings in the format chosen by the
user.
The software at present supports two output formats, viz., PDF format and AUTOCAD editable
DXF Format. Platforms Supported: WINDOWS 2000 and later.
Note:
The objects and text elements in the DXF Format are always accurately placed. However in PDF
format the text placement may be slightly inaccurate especially on a high scale drawing. For
example for a large cabinet (~8 meters in length) the GA Drawing in PDF format may show
slightly misplaced text elements. The texts in DXF Format shall be in their proper positions.
Following are the types of cabinets supported. Please note that the GA Drawings are generated
assuming compartmentalized feeders.
Motor Control Center (MCC)
Power Control / Distribution Center (PCC / PDB)
APFC Panel (Automatic Power Factor Correction Panel)
For any other specific starter type, the user can choose a similar starter option from above and
easily make changes to the respective Control / Power Circuit Drawing Sheet.
Usage of this software is limited to its owner via the terms of its development. PanelDraw is
wholly owned by M/S Magnetix & Electronix, and may not be used or referenced without their
express consent.
1.3.1 Information
For additional information, please visit our website www.paneldraw.com or send us an email at
sales@paneldraw.com
The zipped file can be downloaded be downloaded from the link http://paneldraw.com/free-
download/.
Make sure you read and agree to the Trial Version License Agreement before downloading the
application.
In addition to user documentation, PanelDraw .ZIP file contains the application PanelDraw.exe
for the Windows service. Extract the contents to a convenient folder. It is recommended that you
create a desktop shortcut for the PanelDraw.exe Application File.
PanelDraw Application has been designed to keep setup and installation process easy and light-
weight without too much strain on the system. To run the application, simply Double-Click on the
PanelDraw.exe icon and you are good to go!
As shown in Figure 3.1, enter the overall System Data in Form 1. A brief description of each of
the Fields is given below.
Supply Frequency
Select the supply frequency whether 50 or 60Hz.
Control Voltage
Enter the desired Control Voltage in volts. A suitably rated control transformer shall
automatically be selected by the software to convert the input Supply Line Voltage to this desired
Control Voltage for supply to control and indication elements.
Panel Type
Select the type of panel that best describes your requirement. You can choose between PCC
Panel, MCC Panel and APFC Panel.
Number of Incomers
Input the number of Incomers in the panel.
Mains
Generator 1
Generator 2, etc.
Title
Enter the name of cabinet.
Drawing No.
Enter the drawing number as per your convention. This drawing number shall appear in the Folio
Section of each drawing sheet.
Author
Enter the name of the author of this drawing.
Company
Enter your company name.
Customer
Enter the name of customer for whom the panel is to be made.
Color Format
Select whether you want the output drawings to be colored or in greyscale (black & white).
As shown in Figure 3.2, enter the individual feeder details in Form 2. A brief description of each
of the Fields is given below.
Incomer Details:
Incomer Name
Enter the name of the Incomer. The 1st incomer should be your main incomer. Rest should be
back-ups like generators etc.
Incomer Rating
The Current rating required for the particular incomer.
Feeder Details
Feeder Name
Enter the name of the feeder.
Starter Type
Select the starter type for the feeder. Following options are available:
Feeder Only (only protective circuit breaker)
DOL (Direct On Line Starter)
RDOL (Reversible Direct On Line Starter)
Star Delta Starter
DOL for 3 Phase Heater
Note:
For APFC Panel, only KVAR Rating shall have to be entered for each “Step”.
Connected to Incomer:
This field comes into play if you have multiple incomers. In that case you will have to specify the
default incomer from which supply shall have to be given to this feeder. For example in the case
of a heavy starter like “Blower” you may want to give supply from MAINS, whereas for small
lighting loads or emergency loads, you may want to give supply from the Generator section
As shown in Figure 3.3, enter the incomer and contactor ratings in Form 3. A brief description of
each of the Fields is given below.
Current Rating
The software suggests a suitable current rating for the incomer based on the Panel
KW/KVA/KVAR rating entered in Form 1. You can change this suggested rating through the
drop down menu as per your requirement.
Wiring Material
Select the wiring material for the incomer connection. You can choose between copper and
aluminum.
Incomer Rating
The software suggests a suitable current rating for the incomer based on the Starter
KW/KVAR/Amps rating entered in Form 2. You can change this suggested rating through the
drop down menu as per your requirement.
Contactor Rating
This field is not present for “Feeder Only” type feeders. The software suggests a suitable current
rating for the contactor based on the Starter KW/KVAR rating entered in Form 2. You can
change this suggested rating through the drop down menu as per your requirement.
Wiring Material
Select the wiring material for the starter wiring. You can choose between copper and aluminum.
Figure 3.4: Snapshot of Forms 6 & 7: Incomer Types and Metering Required
As shown in Figure 3.4, enter the incomer types and metering required in Form 4. A brief
description of each of the Fields is given below.
Select the Mains Incomer, Bus-Coupler type and incomer metering required.
Incomer Type
Select the type of incomer.
MCB
SFU
MCCB
MPCB
ACB
And number of poles
3 Pole
4 Pole
Metering Required
Check the meters that are required in the Mains Incomer section:
Amp (Ammeter)
Volt (Voltmeter)
KWH (Energy Meter)
LM (Load Manager)
Bus-Coupler Type
This field does not appear in the 1st incomer and it only starts appearing 2nd incomer onwards.
This is the bus coupler between current incomer and previous incomer.
For example for bus coupler for 2nd incomer, it means the coupler between incomer 1 and
incomer 2. Select the type of this bus coupler.
C/O Switch
MCB
SFU
MCCB
MPCB
ACB
None (Direct short)
Select the incomer type for each feeder and metering required.
Incomer Type
Select the type of incomer (MCB, SFU, MCCB, MPCB, ACB) and number of poles (3P / 4P).
Meter Required
Check if Ammeter is required in the particular feeder.
In this sheet the software builds the proposed GA for the panel and displays it on the screen. The user is
free to modify this GA as required. Following features are supported:
Change the dimensions of any feeder / vertical column simply by editing the dimension text. The panel
automatically gets re-sized.
Delete any unwanted feeder or column by making its dimension zero.
Figure 3.6: Save As Dialog Box: appears when you click Form 5 “FINISH” Button
When you click the final “SUBMIT” Button in Form 4, the File Save As dialog box appears as
shown in Figure 3.5.
1. Choose any convenient folder to save your output file.
2. Name your output file as required.
3. Save As type DXF or PDF format as required.
Note:
If you choose PDF file format, then only one file shall be generated. This file shall have multiple
pages with one Drawing Sheet on each page.
If you choose DXF file format, then multiple files shall be generated. Each file shall have one
Drawing Sheet. The files shall be named as filename_XY.dxf. XY is the two-digit sheet number of
the drawing. For example if the file name is myfile and the number of sheets are 20, then the files
shall be named as myfile_01.dxf, myfile_02.dxf, …, myfile_20.dxf.
Important:
After you click the “Save” button, please wait for some time till you get the following prompt:
You can now check and open your DXF / PDF files in AUTOCAD / PDF Reader respectively. If
you want you can Save the DXF file as a DWG file from your AUTOCAD application.
Important Note:
When you open your DXF file in AUTOCAD application, you will see a blank screen.
Do a [ZOOM ALL] or a [ZOOM EXTENTS] and your drawing will appear.
Hope you have found this manual helpful. For more information please visit
our website or contact us at paneldraw@gmail.com.
Thank you and Happy Designing!