Академический Документы
Профессиональный Документы
Культура Документы
Units system: SI
Steel connections
Joints summary
___________________________________________________________________________________________________________________________
Joint types:
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Joint Member 1 Member 2 Member 3 Braces/Branches
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
BCF Beam Column -- --
BCW Beam Column -- --
BG Beam Girder -- --
BS Left beam Right beam -- --
CS Top column Bottom column -- --
CC Column Continuous beam -- --
CBB Column Right beam Left beam 1 brace mandatory
CVR Beam -- -- 1 brace mandatory
VXB -- -- -- All braces mandatory
CB Column -- -- --
HCBB Column Front beam Right beam 1 brace mandatory
HBBB Girder Beam -- 1 brace mandatory
HXB -- -- -- All braces mandatory
CHB Chord -- -- 1 branch mandatory
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
__________________________________________________________________________________________________________________
Joint : 1 - BS ()
Design status : With warnings
__________________________________________________________________________________________________________________
Ratio : 0.69
Template(s) : MEP BS Flush
Page1
60006-POS-CAL-SF-No2-C4-BCF-H250x250x9x14-R0
Units system: SI
Steel connections
Loads summary
___________________________________________________________________________________________________________________________
Joint types:
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Joint Member 1 Member 2 Member 3 Braces/Branches
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
BCF Beam Column -- --
BCW Beam Column -- --
BG Beam Girder -- --
BS Left beam Right beam -- --
CS Top column Bottom column -- --
CC Column Continuous beam -- --
CBB Column Right beam Left beam 1 brace mandatory
CVR Beam -- -- 1 brace mandatory
VXB -- -- -- All braces mandatory
CB Column -- -- --
HCBB Column Front beam Right beam 1 brace mandatory
HBBB Girder Beam -- 1 brace mandatory
HXB -- -- -- All braces mandatory
CHB Chord -- -- 1 branch mandatory
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
__________________________________________________________________________________________________________________
Joint : 1 - BS ()
Design status : With warnings
__________________________________________________________________________________________________________________
Ratio : 0.69
Template(s) : MEP BS Flush
Page1
60006-POS-CAL-SF-No2-C4-BCF-H250x250x9x14-R0
Units system: SI
Steel connections
Detailed report
___________________________________________________________________________________________________________________________
___________________________________________________________________________________________________________________________
MEMBERS
Configuration
Is apex : No
Right beam
Beams
Beam type : Prismatic member
Beam section : H250X250
Beam material : A36
Left beam
Beams
Beam type : Prismatic member
Beam section : H250X250
Beam material : A36
END PLATE
Connector
Plate extension : Flush
Width : 250 mm
tp: Plate thickness : 16 mm
Plate material : A36
Fy : 0.248 kN/mm2
Fu : 0.4 kN/mm2
Hole type on plate : Standard (STD)
Flush extension length : 10 mm
Beam side
Top flange weld type : Fillet
Top beam flange weld : E70XX
D1: Weld size to top beam flange (1/16in) : 4
Bottom flange weld type : Fillet
Bottom beam flange weld : E70XX
D3: Weld size to bottom beam flange (1/16in) : 4
Welding electrode to beam web : E70XX
Page1
60006-POS-CAL-SF-No2-C4-BCF-H250x250x9x14-R0
D2: Weld size to beam web (1/16in) : 4
End plate
Bolts : M20 A325M
g: Gage - transverse center-to-center spacing : 170 mm
Lev: Vertical edge distance : 40 mm
Leh: Horizontal edge distance : 40 mm
Bolt group (top flange)
Bolts rows number : 1
pfi t: Distance from bolt rows to flange : 40 mm
Bolt group (bottom flange)
Bolts rows number : 1
pfi b: Distance from bolt rows to flange : 40 mm
DEMANDS
Description Ru Pu Mu PufTop PufBot Load type
[KN] [KN] [KN*m] [KN] [KN]
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
CB1 47.00 200.00 0.00 0.00 0.00 Design
CB2 47.00 -200.00 0.00 0.00 0.00 Design
CB3 -47.00 200.00 0.00 0.00 0.00 Design
CB4 -47.00 -200.00 0.00 0.00 0.00 Design
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
GEOMETRIC CONSIDERATIONS
Dimensions Unit Value Min. value Max. value Sta. References
Horizontal center-to-center spacing (gage) [mm] 170.00 53.33 250.00 Sec. J3.3,
DG4 Sec. 2.4,
DG4 Sec. 2.1,
2.4,
DG16 Sec. 2.5
gmin = Max(8/3*d, 2*k1c + 2*d, twb + 2*w + dh)
= Max(8/3*20[mm], 2*0[mm] + 2*20[mm], 9[mm] + 2*6.35[mm] + 21.59[mm])
= 53.33[mm] Sec. J3.3,
DG4 Sec. 2.4
gmax = bfb
= 250[mm] DG4 Sec. 2.1,
2.4,
DG16 Sec. 2.5
Page2
60006-POS-CAL-SF-No2-C4-BCF-H250x250x9x14-R0
GEOMETRIC CONSIDERATIONS
Dimensions Unit Value Min. value Max. value Sta. References
Inner bolt distance (external flange) [mm] 40.00 32.70 -- DG4 Sec. 2.1
d< = 1 [in] ® 20[mm]<
= 1 [in] ® True
Inner bolt distance (internal flange) [mm] 40.00 32.70 -- DG4 Sec. 2.1
d< = 1 [in] ® 20[mm]<
= 1 [in] ® True
Beam
Weld size (external flange) [1/16in] 4 4 -- table J2.4
wmin = wmin
= 6.35 table J2.4
WARNINGS
- The connection does not comply with the section flange width limits (AISC Design Guide 16 - Table 3-6)
- The connection does not comply with the section flange thickness limit (AISC Design Guide 16 - Table 3-6)
Left side beam
Extended end plate
Vertical edge distance [mm] 40.00 33.65 152.40 Sec. J3.5
Lemin = edmin + C2
= 33.65[mm] + 0[mm]
= 33.65[mm] Tables J3.4,
J3.5
Page3
60006-POS-CAL-SF-No2-C4-BCF-H250x250x9x14-R0
GEOMETRIC CONSIDERATIONS
Dimensions Unit Value Min. value Max. value Sta. References
Horizontal center-to-center spacing (gage) [mm] 170.00 53.33 250.00 Sec. J3.3,
DG4 Sec. 2.4,
DG4 Sec. 2.1,
2.4,
DG16 Sec. 2.5
gmin = Max(8/3*d, 2*k1c + 2*d, twb + 2*w + dh)
= Max(8/3*20[mm], 2*0[mm] + 2*20[mm], 9[mm] + 2*6.35[mm] + 21.59[mm])
= 53.33[mm] Sec. J3.3,
DG4 Sec. 2.4
gmax = bfb
= 250[mm] DG4 Sec. 2.1,
2.4,
DG16 Sec. 2.5
Inner bolt distance (external flange) [mm] 40.00 32.70 -- DG4 Sec. 2.1
d< = 1 [in] ® 20[mm]<
= 1 [in] ® True
Inner bolt distance (internal flange) [mm] 40.00 32.70 -- DG4 Sec. 2.1
d< = 1 [in] ® 20[mm]<
= 1 [in] ® True
Beam
Weld size (external flange) [1/16in] 4 4 -- table J2.4
wmin = wmin
= 6.35 table J2.4
WARNINGS
- The connection does not comply with the section flange width limits (AISC Design Guide 16 - Table 3-6)
- The connection does not comply with the section flange thickness limit (AISC Design Guide 16 - Table 3-6)
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
Page4
60006-POS-CAL-SF-No2-C4-BCF-H250x250x9x14-R0
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
pf = min(pf, s)
= min(40[mm], 103.08[mm])
= 40[mm] DG16 Table 3-2
IsFlushConnection ® True
fMn = fb*Mpl/gr
= 0.9*74.99[kN*m]/1.25
= 53.99[kN*m] DG16 Sec 2.5
No prying bolt moment strength [KN*m] 55.24 23.60 CB1 0.43 DG16 Sec 2.5
Pt = Ab*Fnt
= 314[mm2]*620.53[N/mm2]
= 194.85[kN] DG16 Sec 2.5
Mnp = 2*Pt*(Sdn)
= 2*194.85[kN]*(189[mm])
= 73.65[kN*m] DG16 Sec 2.5
fMn = f*Mnp
= 0.75*73.65[kN*m]
= 55.24[kN*m] DG16 Sec 2.5
Bolt rupture with prying moment strength [KN*m] 45.77 23.60 CB1 0.52 DG16 Sec 2.5
Pt = Ab*Fnt
= 314[mm2]*620.53[N/mm2]
= 194.85[kN] DG16 Sec 2.5
Page5
60006-POS-CAL-SF-No2-C4-BCF-H250x250x9x14-R0
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
2 2 2 1/2
Qmaxi = (w'*tp )/(4*ai)*(Fyp - 3*(Fi'/(w'*tp)) )
2 2 2 1/2
= (103.41[mm]*16[mm] )/(4*45.72[mm])*(248.21[N/mm2] - 3*(87.23[kN]/(103.41[mm]*16[mm])) )
= 33.41[kN] DG16 Sec 2.5
fMn = f*Mq
= 0.75*61.02[kN*m]
= 45.77[kN*m] DG16 Sec 2.5
fRn = C*fRn
= 2*77.94[kN]
= 155.88[kN] Tables (7-1..14)
Bolt bearing under shear load [KN] 336.37 47.00 CB3 0.14 Eq. J3-6
Lc-end = Max(0.0, Le - dh/2)
= Max(0.0, 40[mm] - 21.59[mm]/2)
= 29.21[mm] Sec. J3.10
Shear yielding [KN] 536.13 50.00 CB1 0.09 DG4 Eq. 3.12
fRn = f*0.6*Fyp*bp*tp
= 0.9*0.6*248.21[N/mm2]*250[mm]*16[mm]
= 536.13[kN] DG4 Eq. 3.12
pf = min(pf, s)
= min(40[mm], 103.08[mm])
= 40[mm] DG16 Table 3-2
Page6
60006-POS-CAL-SF-No2-C4-BCF-H250x250x9x14-R0
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
IsFlushConnection ® True
fMn = fb*Mpl/gr
= 0.9*74.99[kN*m]/1.25
= 53.99[kN*m] DG16 Sec 2.5
No prying bolt moment strength [KN*m] 55.24 23.60 CB1 0.43 DG16 Sec 2.5
Pt = Ab*Fnt
= 314[mm2]*620.53[N/mm2]
= 194.85[kN] DG16 Sec 2.5
Mnp = 2*Pt*(Sdn)
= 2*194.85[kN]*(189[mm])
= 73.65[kN*m] DG16 Sec 2.5
fMn = f*Mnp
= 0.75*73.65[kN*m]
= 55.24[kN*m] DG16 Sec 2.5
Bolt rupture with prying moment strength [KN*m] 45.77 23.60 CB1 0.52 DG16 Sec 2.5
Pt = Ab*Fnt
= 314[mm2]*620.53[N/mm2]
= 194.85[kN] DG16 Sec 2.5
fMn = f*Mq
= 0.75*61.02[kN*m]
= 45.77[kN*m] DG16 Sec 2.5
Page7
60006-POS-CAL-SF-No2-C4-BCF-H250x250x9x14-R0
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
fRn = C*fRn
= 2*77.94[kN]
= 155.88[kN] Tables (7-1..14)
Bolt bearing under shear load [KN] 336.37 47.00 CB1 0.14 Eq. J3-6
Lc-end = Max(0.0, Le - dh/2)
= Max(0.0, 40[mm] - 21.59[mm]/2)
= 29.21[mm] Sec. J3.10
Shear yielding [KN] 536.13 100.00 CB2 0.19 DG4 Eq. 3.12
fRn = f*0.6*Fyp*bp*tp
= 0.9*0.6*248.21[N/mm2]*250[mm]*16[mm]
= 536.13[kN] DG4 Eq. 3.12
fRn = f*0.6*Fyp*bp*tp
= 0.9*0.6*248.21[N/mm2]*250[mm]*16[mm]
= 536.13[kN] DG4 Eq. 3.12
Beam
Web weld shear strength [KN] 216.49 47.00 CB1 0.22 Eq. J2-4
Fw = 0.6*FEXX
= 0.6*482.63[N/mm2]
= 289.58[N/mm2] Sec. J2.4
1/2
Aw = (2) /2*D/16 [in]*L
1/2
= (2) /2*4/16 [in]*111[mm]
= 498.4[mm2] Sec. J2.4
fRn = 2 * (f*Fw*Aw)
= 2 * (0.75*289.58[N/mm2]*498.4[mm2])
= 216.49[kN] Eq. J2-4
Web weld strength to reach yield stress [KN/m] 2925.55 2010.50 CB1 0.69 Eq. J2-4,
Eq. J4-1
1.5
LoadAngleFactor = 1 + 0.5*(sin(q))
1.5
= 1 + 0.5*(sin(1.57))
= 1.5 p. 8-9
Fw = 0.6*FEXX*LoadAngleFactor
= 0.6*482.63[N/mm2]*1.5
= 434.37[N/mm2] Sec. J2.5
Page8
60006-POS-CAL-SF-No2-C4-BCF-H250x250x9x14-R0
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
1/2
fRw = 2 * (f*Fw*(2) /2*D/16 [in])
1/2
= 2 * (0.75*434.37[N/mm2]*(2) /2*4/16 [in])
= 2.93[kN/mm] Eq. J2-4
fRn = f*Fy*tw
= 0.9*248.21[N/mm2]*9[mm]
= 2.01[kN/mm] Eq. J4-1
fRn = f*0.60*Fy*Ag
= 1*0.60*248.21[N/mm2]*2250[mm2]
= 335.08[kN] Eq. J4-3
Flange weld capacity (external flange) [KN] 759.18 100.00 CB1 0.13 Eq. J2-4
1.5
LoadAngleFactor = 1 + 0.5*(sin(q))
1.5
= 1 + 0.5*(sin(1.57))
= 1.5 p. 8-9
Fw = 0.6*FEXX*LoadAngleFactor
= 0.6*482.63[N/mm2]*1.5
= 434.37[N/mm2] Sec. J2.5
1/2
Aw = (2) /2*D/16 [in]*L
1/2
= (2) /2*4/16 [in]*519[mm]
= 2330.38[mm2] Sec. J2.4
fRn = f*Fw*Aw
= 0.75*434.37[N/mm2]*2330.38[mm2]
= 759.18[kN] Eq. J2-4
Flange weld capacity (internal flange) [KN] 759.18 200.00 CB2 0.26 Eq. J2-4
1.5
LoadAngleFactor = 1 + 0.5*(sin(q))
1.5
= 1 + 0.5*(sin(1.57))
= 1.5 p. 8-9
Fw = 0.6*FEXX*LoadAngleFactor
= 0.6*482.63[N/mm2]*1.5
= 434.37[N/mm2] Sec. J2.5
1/2
Aw = (2) /2*D/16 [in]*L
1/2
= (2) /2*4/16 [in]*519[mm]
= 2330.38[mm2] Sec. J2.4
fRn = f*Fw*Aw
= 0.75*434.37[N/mm2]*2330.38[mm2]
= 759.18[kN] Eq. J2-4
Page9
60006-POS-CAL-SF-No2-C4-BCF-H250x250x9x14-R0
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
pf = min(pf, s)
= min(40[mm], 103.08[mm])
= 40[mm] DG16 Table 3-2
IsFlushConnection ® True
fMn = fb*Mpl/gr
= 0.9*74.99[kN*m]/1.25
= 53.99[kN*m] DG16 Sec 2.5
No prying bolt moment strength [KN*m] 55.24 23.60 CB1 0.43 DG16 Sec 2.5
Pt = Ab*Fnt
= 314[mm2]*620.53[N/mm2]
= 194.85[kN] DG16 Sec 2.5
Mnp = 2*Pt*(Sdn)
= 2*194.85[kN]*(189[mm])
= 73.65[kN*m] DG16 Sec 2.5
fMn = f*Mnp
= 0.75*73.65[kN*m]
= 55.24[kN*m] DG16 Sec 2.5
Bolt rupture with prying moment strength [KN*m] 45.77 23.60 CB1 0.52 DG16 Sec 2.5
Pt = Ab*Fnt
= 314[mm2]*620.53[N/mm2]
= 194.85[kN] DG16 Sec 2.5
Page10
60006-POS-CAL-SF-No2-C4-BCF-H250x250x9x14-R0
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
fMn = f*Mq
= 0.75*61.02[kN*m]
= 45.77[kN*m] DG16 Sec 2.5
fRn = C*fRn
= 2*77.94[kN]
= 155.88[kN] Tables (7-1..14)
Bolt bearing under shear load [KN] 336.37 47.00 CB3 0.14 Eq. J3-6
Lc-end = Max(0.0, Le - dh/2)
= Max(0.0, 40[mm] - 21.59[mm]/2)
= 29.21[mm] Sec. J3.10
Shear yielding [KN] 536.13 50.00 CB1 0.09 DG4 Eq. 3.12
fRn = f*0.6*Fyp*bp*tp
= 0.9*0.6*248.21[N/mm2]*250[mm]*16[mm]
= 536.13[kN] DG4 Eq. 3.12
pf = min(pf, s)
= min(40[mm], 103.08[mm])
= 40[mm] DG16 Table 3-2
IsFlushConnection ® True
Page11
60006-POS-CAL-SF-No2-C4-BCF-H250x250x9x14-R0
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
fMn = fb*Mpl/gr
= 0.9*74.99[kN*m]/1.25
= 53.99[kN*m] DG16 Sec 2.5
No prying bolt moment strength [KN*m] 55.24 23.60 CB1 0.43 DG16 Sec 2.5
Pt = Ab*Fnt
= 314[mm2]*620.53[N/mm2]
= 194.85[kN] DG16 Sec 2.5
Mnp = 2*Pt*(Sdn)
= 2*194.85[kN]*(189[mm])
= 73.65[kN*m] DG16 Sec 2.5
fMn = f*Mnp
= 0.75*73.65[kN*m]
= 55.24[kN*m] DG16 Sec 2.5
Bolt rupture with prying moment strength [KN*m] 45.77 23.60 CB1 0.52 DG16 Sec 2.5
Pt = Ab*Fnt
= 314[mm2]*620.53[N/mm2]
= 194.85[kN] DG16 Sec 2.5
fMn = f*Mq
= 0.75*61.02[kN*m]
= 45.77[kN*m] DG16 Sec 2.5
Page12
60006-POS-CAL-SF-No2-C4-BCF-H250x250x9x14-R0
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
fRn = C*fRn
= 2*77.94[kN]
= 155.88[kN] Tables (7-1..14)
Bolt bearing under shear load [KN] 336.37 47.00 CB1 0.14 Eq. J3-6
Lc-end = Max(0.0, Le - dh/2)
= Max(0.0, 40[mm] - 21.59[mm]/2)
= 29.21[mm] Sec. J3.10
Shear yielding [KN] 536.13 100.00 CB2 0.19 DG4 Eq. 3.12
fRn = f*0.6*Fyp*bp*tp
= 0.9*0.6*248.21[N/mm2]*250[mm]*16[mm]
= 536.13[kN] DG4 Eq. 3.12
fRn = f*0.6*Fyp*bp*tp
= 0.9*0.6*248.21[N/mm2]*250[mm]*16[mm]
= 536.13[kN] DG4 Eq. 3.12
Beam
Web weld shear strength [KN] 216.49 47.00 CB1 0.22 Eq. J2-4
Fw = 0.6*FEXX
= 0.6*482.63[N/mm2]
= 289.58[N/mm2] Sec. J2.4
1/2
Aw = (2) /2*D/16 [in]*L
1/2
= (2) /2*4/16 [in]*111[mm]
= 498.4[mm2] Sec. J2.4
fRn = 2 * (f*Fw*Aw)
= 2 * (0.75*289.58[N/mm2]*498.4[mm2])
= 216.49[kN] Eq. J2-4
Web weld strength to reach yield stress [KN/m] 2925.55 2010.50 CB1 0.69 Eq. J2-4,
Eq. J4-1
1.5
LoadAngleFactor = 1 + 0.5*(sin(q))
1.5
= 1 + 0.5*(sin(1.57))
= 1.5 p. 8-9
Fw = 0.6*FEXX*LoadAngleFactor
= 0.6*482.63[N/mm2]*1.5
= 434.37[N/mm2] Sec. J2.5
1/2
fRw = 2 * (f*Fw*(2) /2*D/16 [in])
1/2
= 2 * (0.75*434.37[N/mm2]*(2) /2*4/16 [in])
= 2.93[kN/mm] Eq. J2-4
fRn = f*Fy*tw
= 0.9*248.21[N/mm2]*9[mm]
= 2.01[kN/mm] Eq. J4-1
Page13
60006-POS-CAL-SF-No2-C4-BCF-H250x250x9x14-R0
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
fRn = f*0.60*Fy*Ag
= 1*0.60*248.21[N/mm2]*2250[mm2]
= 335.08[kN] Eq. J4-3
Flange weld capacity (external flange) [KN] 759.18 100.00 CB1 0.13 Eq. J2-4
1.5
LoadAngleFactor = 1 + 0.5*(sin(q))
1.5
= 1 + 0.5*(sin(1.57))
= 1.5 p. 8-9
Fw = 0.6*FEXX*LoadAngleFactor
= 0.6*482.63[N/mm2]*1.5
= 434.37[N/mm2] Sec. J2.5
1/2
Aw = (2) /2*D/16 [in]*L
1/2
= (2) /2*4/16 [in]*519[mm]
= 2330.38[mm2] Sec. J2.4
fRn = f*Fw*Aw
= 0.75*434.37[N/mm2]*2330.38[mm2]
= 759.18[kN] Eq. J2-4
Flange weld capacity (internal flange) [KN] 759.18 200.00 CB2 0.26 Eq. J2-4
1.5
LoadAngleFactor = 1 + 0.5*(sin(q))
1.5
= 1 + 0.5*(sin(1.57))
= 1.5 p. 8-9
Fw = 0.6*FEXX*LoadAngleFactor
= 0.6*482.63[N/mm2]*1.5
= 434.37[N/mm2] Sec. J2.5
1/2
Aw = (2) /2*D/16 [in]*L
1/2
= (2) /2*4/16 [in]*519[mm]
= 2330.38[mm2] Sec. J2.4
fRn = f*Fw*Aw
= 0.75*434.37[N/mm2]*2330.38[mm2]
= 759.18[kN] Eq. J2-4
NOTATION
Ab: Nominal bolt area
Ag: Gross area
ai: Distance from the interior bolt centerline to the prying force
Aw: Effective area of the weld
bfb: Beam flange breadth
bp: Plate width
C: Bolt group coefficient
C2: Edge distance increment
d: Nominal bolt diameter
d1: Distance from the center of the beam compression flange to the farthest inner load-carrying bolt centerline
d2: Distance from the center of the beam compression flange to the second farthest inner load-carrying bolt centerline
dbmax: Maximum bolt diameter
Page14
60006-POS-CAL-SF-No2-C4-BCF-H250x250x9x14-R0
NOTATION
dh: Nominal hole dimension
discr: Discriminant under the root sign for the calculation of Qmaxi, Qmaxo
D: Number of sixteenths of an inch in the weld size
FEXX: Electrode classification number
Fnt: Nominal tensile stress
Fnv: Nominal shear stress
Fi': Flange force per bolt at the thin plate limit when calculating Qmaxi for end-plate configurations with large inner pitch distances
Fu: Specified minimum tensile strength
Fw: Nominal strength of the weld metal per unit area
Fy: Specified minimum yield stress
Fyp: Specified minimum yield stress of plate
g: Transversal gage between bolts
gmax: Maximum bolt gage
gmin: Minimum bolt gage
gr: Load factor to limit connection rotation at ultimate moment to 10% of simple span rotation
h1: Distance from the compression side of the beam to the farthest inner load-carrying bolt line
IsFlushConnection: Is flush connection
k1: Bearing factor
k1c: Distance from column web centerline to flange toe of fillet
k2: Bearing factor
Lc-end: Clear distance
Le: Edge distance
Lemax: Maximum edge distance
Lemin: Minimum edge distance
Lp: Plate length
L: Length of weld
LoadAngleFactor: Load angle factor
Mnp: No prying moment
Mpl: End plate or column flange flexural strength
Mq: Connection strength for the limit state of bolt fracture with prying action
edmin: Minimum edge distance
n: Bolts rows number
nc: Number of bolt columns
pf: Distance from the bolt centerline adjacent the beam tension flange to the near face of the beam tension flange
pfi: Distance from the inside of a beam tension flange to the nearest inside bolt row
pfmin: Minimum distance from the inside of a beam tension flange to the nearest inside bolt row
Pt: Bolt tensile strength
f: Design factors
fb: Design factor for bending
fMn: Design or allowable strength
fRn: Design or allowable strength
fRn: Design or allowable strength per unit length
fRw: Fillet weld capacity per unit length
Qmaxi: Maximum possible prying force for interior bolts
s: Distance from the most inside or outside tension bolt row to the edge of a yield line
smin: Minimum spacing
s: Longitudinal bolt spacing
Lc-spa: Distance between adjacent holes edges
Sdn: Sum of all distances from centerline of compression flange to the nth bolt row
tp: Thickness of the connected material
Tb: Minimum fastener pretension
tp: Plate thickness
tw: Web thickness
twb: Thickness of beam web
q: Load angle
ThickPlateSmallerBoltsBehaviorApply:Thick plate behavior controled by bolt rupturwe without prying action apply
ThinPlateYieldingApply: Thin plate behavior controlled by end-plate yielding apply
wmin: Minimum weld size required
w': Width of end-plate per bolt minus the bolt hole diameter
w: Weld size
Yp: Yield line mechanism parameter
Page15
60006-POS-CAL-SF-No2-C4-BCF-H250x250x9x14-R0
Units system: SI
Steel connections
Connections elements summary
___________________________________________________________________________________________________________________________
CONNECTION ELEMENTS
Plates
ID Plate Material Length Width Thickness Qty.
[mm] [mm] [mm]
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
P0 PL 16x250x270 A36 270.00 250.00 16.00 1
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Bolts
ID Bolt Grade Length Diameter Qty.
[mm] [mm]
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
B0 M20 A325M G8_8 32.00 20.00 4
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Welds
ID Weld Type Strength Size Length
[KN/mm2] [mm]
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
W0 E70XX Fillet 0.48 6[mm] 2852.00
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Element Description ID
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Bolts - Support side M20 A325M B0
Plate - Support side PL 16x250x270 P0
Weld - Beam side E70XX W0
Weld - Beam side E70XX W0
Weld - Beam side E70XX W0
Weld - Beam side E70XX W0
Weld - Beam side E70XX W0
Weld - Beam side E70XX W0
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Notes
Joint type:
BS : Beam splice
Connector type:
MEPBS : Moment end plate
Page1