Академический Документы
Профессиональный Документы
Культура Документы
1 Identification 2
2 Introduction 2
4 General Description 3
5 Functional Description 4
6 External Interfaces 6
8 Physical Description 10
9 Power Supply 12
1 Identification
2 Introduction
This document describes the Combined NT Unit version F (FANT-F) which is part of the
7360 Intelligent Services Access Manager (7360 ISAM) FX.
4 General Description
The LT boards are responsible for the physical termination of user interfaces and non-
blocking user aggregation.
The FANT-F AC board must be used at the NT-A and/or the NT-B position of the 7360
ISAM FX subrack. Figure 1 shows the position of the FANT-F in the ISAM system.
Management-A
interface
LT #0
LT #1
NT-A
(FANT-F)
NTIO
A Power unit
Uplink/Network
Interfaces
Alarm IO board
NTIO
B LT #N-1
NT-B
(FANT-F) LT #N
Management-B
interface ISAM system
5 Functional Description
PBA-FANT-F
FIM BIM
BITS-Interface BITS Interface
ToD and 1PPS interface REFIN REFIN ToD and 1Hz Interface
8kHz-Interface NT Reference Clock
19.44MHz-Interface REFOUT MCSD REFOUT NT ToD/1PPS
10MHz GPS Interface LT Reference Clocks
Peer NT Reference Input Clock
PNTIN Peer NT ToD/1PPS
LT16 LT SerdesItf#16
NT Front Uplink Interface #4 FUI#4
NUTS BUI0 Backplane Uplink Itf#0
NT Front Uplink LEDs UPLED BUI1 Backplane Uplink Itf#4
NTIO/NTAP-Powering Itf
PSIM NT Power Supply Itf
SMAS-Powering Itf
• MCSD:
The Master Clock Synchronization and Distribution (MSCD) provides the following
functionality:
• System Network Timing Reference (NTR)
• Synchronization Input references from BITS/SSU, Synchronous Ethernet input link
data clocks, IEEE-1588 ordinary or boundary clock.
• Synchronization Output reference clocks towards:
- The shelf-based LT boards (backplane connections): 8 kHz.
- The internal NTR signal from the active NT board to the standby NT board in
a redundant NT board pair (backplane connection): 8 kHz.
- The external NTR daisy-chain interface (located at the NT board front): 8 kHz and
19MHz.
- The external BITS/SSU out interface (located at the NT board front):
independently configurable to 2048 kHz, E1 or DS1 signal.
• Performance for SSU / BITS input/output: compliance with ITU-T G.813 Option 1:
ETSI.
• Performance for Synchronous Ethernet (SyncE) input/output: compliance with ITU-T
G.8262 Option 1: ETSI
• NUTS:
The Network/User Transport and Switching (NUTS) provides the interface and
switching circuitry for the front and back related uplink/network interfaces to/from
the LT slots.
• PSIM:
The Power Supply Interface Module (PSIM) converts the rack power supply into all
necessary voltages as required by the used components.
• FIM:
The Frontplate Interface Module (FIM) located at the front stiffener holds the
physical interfaces (four SFP+, one 10/100/1000Base-T interface) together with a
visual port status indication. The FIM also hosts a Management Interface (CRAFT)
together with the ACO functionality.
• BIM:
The Backplane Interface Module (BIM) constitutes all the necessary control,
management, and data plane related interface inside the complete ISAM system.
6 External Interfaces
The following external interfaces are accessible via the front panel:
Communication Interfaces
5 communication interfaces are available via the front panel:
• 1 x fixed 10/100/1000BaseT port:
This port can work both in 10Mbit, 100Mbit or 1GE mode.
• 4 x 10GE SFP+ port:
This port can work both in 1 GE mode (with standard SFP optics) and in 10 GE mode
(with SFP+ optics).
Management Interfaces
The following management interfaces are available via the front panel:
• Local Craft Management interface (LCMI) (RJ45 connector)
• An Alarm Cut-Off Switch (ACOS) and LED (ACOLED)
Note: any of the five communication interfaces can also be used as management interface.
The following clock interfaces are available via the front panel:
• BITS input interface (RJ45 connector)
• BITS output interface (RJ45 connector)
• Time of Day (ToD) interface
• 10MHz GPS interface (SMA connector)
• 1pps interface (SMA connector)
• Daisy-Chain NTR clock output interface (RJ45 connector)
(1 of 2)
(2 of 2)
BITS Interface
The BITS/DC IN/OUT interfaces are mapped to two physical RJ45 connectors.
ToD_UART_T/F ToD UART TX, PTP Master mode (differential pair, 100 ohm) O 8, 7
ToD UART RX, PTP Slave mode (differential pair, 100 ohm) I
ToD_1PPS_T/F 1PPS output, PTP Master mode (differential pair, 100 ohm) O 6, 3
These ACU interfaces can be found on the backplane of the subrack, for more
information refer to the 7360 ISAM FX Hardware Installation Manual.
8 Physical Description
LEDs
SFP cages
1PPS Signal
10MHz Signal
CRAFT Interface
Time of Day
BITS in
BITS out
Dimensions:
The dimensions of the FANT-F AC are:
• Board height: 405 mm
• Width: 30 mm
• Depth: 205/225 mm
ACO
ALM PWR
ACO A/S
FSM2 FSM1
FSM4 FSM3
Table 8 gives the definitions of the system status LEDS on the FANT-F.
Port Description
9 Power Supply
The FANT-F is compatible with -48 Vdc nominal and -60 Vdc nominal power supply
systems.
Note: Country dependent tolerances exist regarding the nominal battery voltage values.