Академический Документы
Профессиональный Документы
Культура Документы
DEH-3900MP
DEH-2920MP
DEH-2900MP
Installation
Note: DIN Front-mount
• Check all connections and systems before final
installation.
• Do not use unauthorized parts. The use of
Installation with the rubber bush
unauthorized parts may cause malfunctions. Dashboard Mounting sleeve
• Consult with your dealer if installation requires
drilling of holes or other modifications of the 182
Screw
Dashboard or Console
OF
OF
N
N
the power terminal of the auto antenna.
STAR
STAR
Otherwise, battery drain or malfunction may
T T result.
• Black cable is ground. This cable and other prod-
uct’s ground cable (especially, high-current prod-
ACC position No ACC position ucts such as power amp) must be wired separate-
ly. Otherwise, fire or malfunction may result if
• Use this unit in other than the following condi- they are accidentally detached.
tions could result in fire or malfunction.
— Vehicles with a 12-volt battery and negative • Cord function may differ according to the
8. Cap (1*) grounding. product, even if cord color is the same. When
Do not remove cap if this — Speakers with 50 W (output value) and 4 ohm connecting this system, be sure to check all
terminal is not in use. to 8 ohm (impedance value). manuals and connect cords correctly.
• To prevent short-circuit, overheating or malfunc-
tion, be sure to follow the directions below.
— Disconnect the negative terminal of the bat-
tery before installation.
— Secure the wiring with cable clamps or adhe-
sive tape. To protect the wiring, wrap adhe-
sive tape around them where they lie against
metal parts.
— Place all cables away from moving parts,
such as gear shift and seat rails.
— Place all cables away from hot places, such as
near the heater outlet.
— Do not pass the yellow cable through a hole
into the engine compartment to connect to a
battery.
— Cover any disconnected cable connectors
with insulating tape.
— Do not shorten any cables.
— Never cut the insulation of the power cable of
this unit in order to share the power to other
equipment. Current capacity of the cable is
limited.
— Use a fuse of the rating prescribed.
— Never wire the speaker negative cable directly
to ground.
— Never band together multiple speaker’s nega-
14. ISO connector tive cables.
Note:
In some vehicles, the ISO connector may be
divided into two. In this case, be sure to
connect to both connectors.
Connection Diagram 16. Connect with RCA cables (sold separately)
17. Power amp (sold separately)
1. Rear output 18. Blue/white
2. This product Connect to system control terminal of the power
3. Antenna jack amp (max. 300 mA 12 V DC).
4. Fuse (10 A) 19. System remote control
5. Wired remote input 20. Blue/white (7*)
Hard-wired remote control adaptor can be con- Connect to auto-antenna relay control terminal
nected (sold separately). (max. 300 mA 12 V DC).
6. Note: 21. Blue/white (6*)
Depending on the kind of vehicle, the function of 22.The pin position of the ISO connector will differ
3* and 5* may be different. In this case, be sure depends on the type of vehicle. Connect 6* and
to connect 2* to 5* and 4* to 3*. 7* when Pin 5 is an antenna control type. In
7. Connect leads of the same color to each other. another type of vehicle, never connect 6* and 7*.
8. Cap (1*) 23. Left
Do not remove cap if this terminal is not in use. 24. Right
9. Yellow (3*) 25. Rear Speaker
Back-up (or accessory) 26. Perform these connections when using the
10. Yellow (2*) optional amplifier.
Connect to the constant 12 V supply terminal. 27. Yellow/black
11. Red (5*) If you use an equipment with Mute function,
Accessory (or back-up) wire this lead to the Audio Mute lead on that
12. Red (4*) equipment. If not, keep the Audio Mute lead free
Connect to terminal controlled by ignition swich of any connections.
(12 V DC).
13. Black (chassis ground)
Connect to a clean, paint-free metal location.
14. ISO connector
Note:
In some vehicles, the ISO connector may be
divided into two. In this case, be sure to connect
to both connectors.
15. Speaker leads
White: Front left +
White/black: Front left ≠
Gray: Front right +
Gray/black: Front right ≠
Green: Rear left +
Green/black: Rear left ≠
Violet: Rear right +
Violet/black: Rear right ≠
Connecting the Units
3. Antenna jack
5* 4* 4. Fuse (10 A) 18. Blue/white
Connect to system control terminal of the
7. Connect leads of the same
power amp (max. 300 mA 12 V DC).
color to each other.
8. Cap (1*)
Do not remove cap if this 19. System remote control
terminal is not in use. 20. Blue/white (7*)
Connect to Auto-antenna relay control terminal
(max. 300 mA 12 V DC).