Академический Документы
Профессиональный Документы
Культура Документы
Mullikin
To counteract this situation, we must change the angle at which the neck meets the body of
the instrument, bringing the bridge end of the fingerboard up. Fortunately, we have a quick
and minimally invasive method of doing this, which does not require the entire neck to be
reset. It’s known as a projection or pitch raise. Some luthiers refer to it as a “New York neck
reset.”
I like to think of projection as the point where the fingerboard would collide with the bridge if
it suddenly grew longer, a la Pinocchio’s nose.
To measure the projection, take two rulers, one of which should be roughly as long as the
fingerboard (a 30 cm ruler works great for violin and viola, 60 cm for cello). Using a ruler that
is too short can give you a false reading because of the scoop in the fingerboard. Rest the
long ruler along the center of the fingerboard and slide it forward so it reaches all the way to
the bridge (or to the bridge position, if there is no bridge).
Use the other ruler to measure the distance from the top of the instrument to the bottom of
the long ruler, as pictured above. That measurement is the projection. In our shop, we like to
set violin necks with a projection of 27.5 mm , 30-33 mm for viola and 82.5-84 mm for cello.
Order of Operations
Often we are working with an instrument that needs a lot of other set up work done at the
same time. If the customer would like a fingerboard planing and/or a new sound post along
with the projection raise, it’s important to take care of those things first because they can
alter the projection slightly. Similarly, if the instrument is getting a new bridge, make sure to
raise the projection first, since it directly impacts the string heights.
Doing so will prevent the top from binding to the neck root and creating a crack next to the
block.
Next, I gently coax the seam open using a small hammer and my “seam knocker.”
The placement of your hands is also critical. I make sure to support the edge of the top with
my fingers, while my thumb rests on the back directly behind the seam knocker to help guide
the hammer.
For cello, the arrangement is the same, except I always add some protection on the rib so I
When the seam knocker is positioned just right, tap it gently but assertively with the
hammer. Then, inspect the seam. If it’s still closed tightly, repeat the process. While some
may balk at this method of opening (believe me, I was terrified the first time I tried it), when
applied correctly, it has absolutely no adverse impact on the instrument.
I discourage using moisture, as that will re-hydrate the hide glue and increase its strength.
Moisture will also swell the wood and make everything tighter. Some luthiers apply alcohol to
loosen glue joints. I rarely resort to this, because it makes me nervous to have alcohol so
close to varnish.
Once you have created a small opening, gently slide your opening knife inside, still using dry
soap as a lubricant. The knife should have a very slight wedge shape to the blade, which will
help the seam pop open.
Look at the picture and see how I support the top with my fingers at all times. This allows me
to feel how the knife is affecting the top and I can stop immediately if anything feels amiss.
Work your way down to about the middle of the bout and then up to the top block. Repeat
the process, starting with your seam knocker, on the opposite bout.
The trickiest part is often getting the top to release from the block. I like to remove the end
button so that I can look inside the instrument and ensure that my opening knife is working
its way into the seam and not into the block or the top. Keep sliding the knife in, keeping the
blade perpendicular to the grain, as the area around the block is especially susceptible to
When the top is free of the block, you should be able to gently wiggle the neck back and forth
to open the joint where the shim will be placed. Be sure to support the button with your palm
as you do this.
http://www.pasewicz.com/wp-content/uploads/2014/11/Ne
ck-Loose-for-Projection-Raise.mp4
Fitting the Shim
Next, we get the shim to the right size and thickness. Take your shim stock and hold it next
to the neck mortice to mark the length.
I cut the shim to length with my micro-saw and use a knife to split the piece to the right
height. Approximate this dimension by guesstimating the thickness of the top and adding
about 2 mm, roughly 5 mm for a violin or viola, 7-8 mm for a cello. I like to split the shim
along the grain lines because it will make it easier to cut down later after it’s glued in.
Slip the shim under the fingerboard and slide it down into the gap between the neck root and
the top. You will need to tilt the neck back a little in order to do this (again, support the
button!). Using the tip of a knife to manipulate the shim will greatly aid the process.
With the shim in place, secure a few closing clamps on the instrument to support the open
seams while you measure the projection.
If the instrument is getting a new bridge, simply measure the projection without the strings
on. If you will be reusing the existing bridge, put the instrument up to tension with all four
strings and check the string heights.
Planing the shim down will be easier if you glue a thin piece of veneer to the surface of your
bench and cut a little notch into it as a stopper.
Plane off about .10 mm, measuring with the digital calipers. Place the shim in the mortise,
replace clamps and check the projection or string heights again. Continue working this way
until the desired numbers are reached.
Occasionally, you will find that only a very thin shim is needed. If the ebony gets down to
about .25 mm and it’s still too thick, you may use a piece of cardstock (business cards work
well for this) instead of ebony. Just be sure to “ebonize” it with a black permanent marker
before gluing it in.
Set instrument in a safe spot while the glue dries (minimum of 3 hours).
Final Touches
When the glue is dry, remove the clamps and use a sharp knife to trim down the millimeter or
so of the shim that’s still visible.
And here:
Seal the color in with a thin coat of clear and you’re done.
Share this: