Академический Документы
Профессиональный Документы
Культура Документы
Product
Catalouge
2018
3
Index
Supports 7. One-Direction 27. Joint Plate Kit 51 – 65. RRU and
Offset Family ERS-mount Families
and brackets 11. Symmetric
31. Crossover Kit
35. Combiclamp Family 67. RRU Support
Offset Family 71. RRU Adaptor Plate
39. 3-sector Antenna
15. Small Universal Mounting 75. Antenna Offset
Pole Mount
43. Rafter Bracket Kit
19. Raking Tower
47. Telescopic
Leg Offset Family
Strut Support
23. Vertical Tower
Leg Offset Family
Your direction
is our goal.
In a world where everyone has to depend on each other,
Mafi wants to make your life easier.
For 25 years our customer relations has been just as important
as the quality of our products. Knowing this, we have
built the worldwide company we are today.
On paper, Mafi is an engineering company that designs,
tests, manufactures and delivers steelwork solutions.
But we go further than that:
We are responsive – we see it as part of our mission
to understand your actual need.
We are explorers — we are always looking for new
ways to enhance our solutions.
We are reliable — we always deliver on our promises.
Whatever it takes to get you there, we’re always
prepared to go the extra mile; making us your preferred
strategical partner.
Every design follows these guidelines: Design recommendations given by MAFI concerning the use of
a particular product are based on site information provided by
• Make the kit as easy as possible to assemble and the customer. MAFI provides a Declaration of Performance for
provide clear assembly instructions. the product itself, and it is the customer’s responsibility to
• The kit is packed in as small a box as possible to ensure that imposed loads are within the capacity of the
ensure efficient storage and transport. product.
It is always the responsibility of the site designer to verify that
• Make the product as light as possible for easy
the parent structure is adequate to support the loads imposed
handling on site.
by the product and that the installation of the product will
Every kit comes with a data sheet with load tables. comply with the installation instructions and with statutory
The load tables give the maximum ultimate vertical and site owner’s rules and regulations.
and horizontal loads that may be applied to the kit.
5
When MAFI began in 1992, our business idea was to offer standardised
products in a young and fast growing industry segment, when almost
every telecom site had a unique design. Our goal has always been
to simplify site builds solutions for our customers so that they can focus
on their core business and manage more efficient and profitable rollouts.
25 years later, I find that we have achieved these goals – and surpassed
them by a considerable margin! Today, our solutions are found in leading
telecom suppliers' product portfolios and used worldwide.
Over the years we have accumulated experience and built up
depth of expertise that – according to our customers – makes us
one vof the leading suppliers in our segment.
We develop, test and manufacture standardised products, in full
accordance with the national requirements and standards of our global
markets. Every detail is characterised by accuracy and Swedish quality.
We provide detailed guidance on where and how our solutions can be
used, whether it concerns wind loads or weights on a mast. Regardless
of where our products are manufactured – Asia, The Far East, Mexico
or Sweden – we always guarantee MAFI's high quality.
And now we are marching into the future!
Recently, we moved to new, modern premises. This has enabled
us to locate our entire business, including an efficient and partially
robotised logistics centre, under one roof, thereby creating
just started.
It is no secret that this is one of the keys to our success!
We are currently working to dramatically shorten lead times
for developing new products, through investment in new software,
machinery and highly skilled people.
This is already enabling us to provide a comprehensive product range,
from volume products through to specialised niche solutions.
We are laying the foundation for developing further patented products
which, like their predecessors, can become global top sellers.
It has been our customers' needs that have guided our business
throughout the years. We will continue to listen to you, to inform
our experience and expertise. In this way, I hope that during at least
another 25 years, we will be able to provide you with solutions
that contribute to your success, swiftly and affordably.
MAFI 3263
One-Direction
Offset Family
—
Designed to allow an equipment pole to be offset
from a parent pole or tower leg.
Additional features:
• Lightweight but rigid.
• Few parts and easy to assemble.
8 Rev 4 *Article MAFI 3263/3272/3273
MAFI 3263*
One-Direction
Offset Family
Flexibility
The 3263, 3265 and 3273 brackets can be mounted on any
vertical round member from Ø 25 – 169 mm and also on
MAFI 3263
vertical angel sections. The offset pole can be Ø 60.3 mm
or Ø 76.1 mm with the standard Ø 76 mm U bolts supplied,
or optionally up to Ø 114.3 mm.
The 3273 provide a maximum c/c offset of 230 mm and the
3263 and 3265 provide a maximum c/c offset of 420 mm
respectively 400 mm. The 3272 fits round members from
Ø 48 – 193 mm and provides a maximum offset of
800 mm. The 3272 incorporates a double clamp to cope with
the high torque loads impose by antennas at a large offset.
Content of kit
Parent pole/leg
40 × 40 mm
up to 120 × 120 mm
40 × 40 mm up to
120 × 120 mm
Tightening torque
MAFI 3272
Threaded rods M12: 31 Nm
U-bolts M12: 31 Nm
Part list
Parts Material Quantity
Package data
Product Length (mm) Width (mm) Height (mm) Weight (kg)
Product options
MAFI 3265, 400 mm tube offset kit that fits Ø 89 - Ø 114 mm
EN 1090
Ft
Vertical load
Max Supported Equipment mass MAFI
3263/3265/3273 = 120 kg
Max Supported Equipment mass MAFI 3272 = 60 kg
3273 230
3263 420
3265 400
3272 800
© 2017 MAFI AB. All rights reserved.
11
MAFI 3268*
Symmetric
Offset Family
—
Designed to provide support for two similar antennas
offset symmetrically from a central parent pole.
Additional features:
• Two lengts for optimized installation.
• Double or triple installation of antennas.
12 Rev 5 *Article MAFI 3268/3270
MAFI 3268*
Symmetric
Offset Family
MAFI 3268
Flexibility
Fits any round member from Ø 76 – 169 mm.
The offset poles can be Ø 60.3 or 76.1 mm and may
be specified in any length. The 3268 gives a c/c distance
between the outer antennas of 800 mm, and the 3270
gives a c/c distance between the outer antennas of 1700 mm.
How to Order
To order this kit, please contact MAFI quoting article number: Content of kit MAFI 3270
Parent pole/leg
Ø 76 – 169 mm
MAFI 3268
Equipment pole
Ø 60 – 76 mm
MAFI 3270
Tightening torque
Part list
Parts Material Quantity
Package data
Product Length (mm) Width (mm) Height (mm) Weight (kg)
Product options
MAFI 44040, U-bolt kit for tube Ø 89 – 114 mm.
EN 1090
Ft
Fmass Fmass
Design resistance data
The load limits given in this data sheet apply to the MAFI
product only. The designer should always check that
the supporting structure can safely carry the loads applied
to it by the MAFI product.
Vertical load
Max Supported Equipment mass (Fmass) MAFI 3268 = 90 kg
Max Supported Equipment mass (Fmass) MAFI 3270 = 60 kg
Horizontal load
Ultimate transient horizontal load per bracket (Fwind)
MAFI 3268 = 2000 N
Ultimate transient horizontal load
per bracket (Fwind) MAFI 3270 = 2000 N.
76.1 298
88.9 353
101.6 408
114.3 462
152.4 627
168.9 698
MAFI 3274
Small Universal
Pole Mount
—
Designed for mounting an equipment pole on a parent
pole or tower leg. The kit consists of a pair of brackets
with all necessary fixings.
Additional features:
• Simplifies close tube to tube mounting.
• Suitable for a wide range of tube dimensions.
16 Rev 2 Article MAFI 3274
MAFI 3274
Small Universal
Pole Mount
Flexibility
Can be mounted on any round member from
Ø 25 – 114 mm as well as equal-angle or square section
members up to 80 × 80 mm. Equipment poles
can range from Ø 48 – 114 mm.
How to Order
To order this kit, please contact MAFI quoting article number:
3274 or E-order number (SEG): 6000688
Contact information can be found at www.mafi.se.
Content of kit
Parent pole/leg
40 × 40 up to 80 × 80 mm
Ø 25 – 114.3 mm
Equipment pole
Ø 48 – 114.3 mm
Tightening torque
Threaded rods: 18 Nm
Part list
Parts Material Quantity
Package data
Product Length (mm) Width (mm) Height (mm) Weight (kg)
Product options
Tubes of various lengths and diameter can be ordered from MAFI.
EN 1090
Fmass
Horizontal load
Ultimate transient horizontal load per bracket = 4000N
Fwind
Rotational slip resistance
When high side forces can be expected, use the tables below
Mresisting
to check for rotational slip when mounting on a circular pole.
Use ultimate loads and equipment offset to calculate
the applied torque.
42.3 152
48.3 178
60.3 230
76.1 298
88.9 353
101.6 408
114.3 462
MAFI 3610*
Raking Tower
Leg Offset
Family
—
Designed for mounting an equipment pole on a raking
parent pole or tower leg. The kits consists of a pair
of brackets with all necessary fixings.
Additional features:
• Simplifies installation on raking towers.
• Suitable for L profiles and round members.
20 Rev 3 *Article MAFI 3610/3613
MAFI 3610*
Raking Tower
Leg Offset
Family
Flexibility
The 3610 can be mounted on any round member from
Ø76 – 139 mm as well as equal-angle or square section MAFI 3610
members from 60 × 60 – 120 × 120 mm, while the 3613 can
be mounted on any round member from Ø 139 – 245 mm
as well as equal-angle or square section members from
120 × 120 – 200 × 200 mm.
Offset poles for either kit can range from Ø 60 – 114 mm
with a maximum upper offset of 350 mm c/c and
a lower fixed offset of 250 mm c/c.
Parent pole/leg
Equipment pole
Ø 60 – 76 mm
(Ø 114 mm as option)
Package data
Product Length (mm) Width (mm) Height (mm) Weight (kg)
Product options
MAFI 2867-1; U-bolt kit for attaching Ø 114 equipment tube.
EN 1090
Ft
Fmass
Design resistance data
The load limits given in this data sheet apply to the MAFI
product only. The designer should always check that
the supporting structure can safely carry the loads applied
to it by the MAFI product.
Vertical load
Max Supported Equipment mass (including weight
of offset pole) MAFI 3610/3613 = 250 kg
Horizontal load
Ultimate transient horizontal load per
offset arm (Fwind) = 4000 N
Mresisting
Rotational slip resistance
When high side forces can be expected, use the table below
to check for rotational slip when mounting on a circular pole.
Use ultimate loads and equipment offset to calculate the
applied torque.
42.3 152
48.3 178
60.3 230
76.1 298
88.9 353
101.6 408
114.3 462
152.4 627
168.9 698
© 2017 MAFI AB. All rights reserved.
23
MAFI 3611*
Vertical
Tower Leg
Offset Family
—
Designed for mounting an equipment pole on a vertical
parent pole or tower leg. The kits consists of a pair of
brackets with all necessary fixings.
Additional features:
• Simplifies installation on vertical towers.
• Suitable for L profiles and round members.
24 Rev 3 *Article MAFI 3611/3612/3614/3615
MAFI 3611*
Vertical
Tower Leg
Offset Family
Flexibility
The 3611/3612 can be mounted on any round member from
Ø 76 – 139 mm as well as equal-angle or square section
members from 60 × 60 – 120 × 120 mm, while the 3614/3615
can be mounted on any round member from
MAFI 3611 MAFI 3612
Ø 139 – 245 mm as well as equal angle or square section
members from 120 × 120 – 200 × 200 mm.
Offset poles for any of the kits can range from
Ø 60– 114 mm. The small and large offset arms provide
maximum c/c offsets of 250 mm and 350 mm respectively.
Parent pole/leg
Equipment pole
Ø 60 – 76 mm
(114 mm as option)
Tightening torque
Large clamps (MAFI 3614 & 3615) Bolt M16: 210 Nm
Threaded rods M12: 31 Nm
Part list U-bolts M12: 31 Nm
Parts Material Quantity
Package data
Product Length (mm) Width (mm) Height (mm) Weight (kg)
Product options
MAFI 2867-1; U-bolt kit for attaching Ø 114 equipment tube.
EN 1090
Ft
Fmass
Vertical load
Max Supported Equipment mass (including weight
of offset pole) MAFI 3611/12/14/15 = 250 kg
Ultimate Transient Man-Load MAFI 3611/3612 = 2.4 kN
42.3 152
48.3 178
60.3 230
76.1 298
88.9 353
101.6 408
114.3 462
152.4 627
168.9 698
© 2017 MAFI AB. All rights reserved.
27
MAFI 5310*
Joint
Plate Kit
—
Designed to provide perpendicular joints between
solid or thick-walled circular member and square tubes.
Additional features:
• Smooth and easy installation.
• Tight mounted against towers and masts.
28 Rev 2 *Article MAFI 5310/5311/5312
MAFI 5310*
Joint
Plate Kit
MAFI 5310
Flexibility
Fits parent poles ranging from Ø 25 – 60 mm
and square beams ranging from 50 × 50 – 60 × 60 mm.
MAFI 5311 MAFI 5312
Detailed design data
Detailed design data for this product
can be found at www.mafi.se.
How to Order
To order this kit, please contact MAFI quoting article number:
5310 or E-order number (SEG): 6000671
5311 or E-order number (SEG): 6000672
×2
5312 or E-order number (SEG): 6000673
Content of kit
Contact information can be found at www.mafi.se.
Art. 5310:
Ø 25 – 35 mm
Art. 5311:
Ø35 – 60 mm
Art. 5312:
50 × 50 – 60 × 60 mm
Equipment pole
50 × 50 – 60 × 60 mm
Tightening torque
U-bolt M12: 15 Nm
Part list
Parts Material Quantity
Package data
Product Length (mm) Width (mm) Height (mm) Weight (kg)
Product options
MAFI 5320, 5321: Crossover kit for members Ø 76.1, Ø 114.3, 50 × 50 – 60 × 60 mm.
EN 1090
Mt
Fmass
Vertical load
Max Supported Equipment mass per joint Fmass = 100 kg
Tightening torque
Recommended tightening torque, with oiled nuts and bolts in
delivery state Mt= 15 Nm.
MAFI 5320*
Crossover Kit
—
Designed to provide perpendicular joints between
circular members and square tubes.
Additional features:
• Simplifies installation of round tubes mounted
to square beams.
32 Rev 2 *Article MAFI 5320/5321
MAFI 5320*
Crossover
Kit
MAFI 5320
Flexibility
MAFI 5320 fits circular tubes of Ø 76.1 mm and square beams
ranging from 50 × 50 – 60 × 60 mm. MAFI 5321 fits
circular tubes of Ø 114.3 mm and square beams ranging
from 50 × 50 – 60 × 60 mm.
How to Order
To order this kit, please contact MAFI quoting article number:
5320 or E-order number (SEG): 6000674
5321 or E-order number (SEG): 6000675
Contact information can be found at www.mafi.se.
Content of kit
Circular tube
Art. 5320:
Ø 76.1 mm
Art. 5321:
Ø 114.3 mm
Square tube
50 × 50 – 60 × 60 mm
Tightening torque
U-bolt M12: 15 Nm
Part list
Parts Material Quantity
Package data
Product Length (mm) Width (mm) Height (mm) Weight (kg)
Product options
MAFI 5310, 5311, 5312: Joint plate kits for members Ø 25 – 60 mm,
50 × 50 – 60 × 60 mm.
EN 1090
Fr
Fmass
Fwind
Vertical load
Max Supported Equipment mass Fmass = 100 kg
76.1 298
114.3 462
MAFI 43249*
Combiclamp
Family
—
Designed to provide perpendicular joints
between two circular members.
Additional features:
• Smooth and easy installation.
• Tight mounted against towers and masts.
36 Rev 3 *Article MAFI 43246/43247/43248/43249
MAFI 43249*
Combiclamp
Family
MAFI 43249
Flexibility
MAFI 43249 joints two circular tubes of Ø 114.3 mm.
MAFI 43248 joints one circular tube of Ø 114.3 mm
to a circular tube of Ø 76.1 mm.
MAFI 43247 joints two circular tubes fo Ø 76.1 mm.
MAFI 43246 joints one circular tube of Ø 60.3 mm MAFI 43248 MAFI 43247
to a circular tube of Ø 48.3 mm. The products are delivered
with all necessary bolts and nuts.
How to Order
To order this kit, please contact MAFI quoting article number:
43249
43248 MAFI 43246
43247
43246
Contact information can be found at www.mafi.se.
Parent pole/leg
MAFI 43246
Tightening torque
MAFI 43249
U-bolt M12: 15 Nm
U-bolt M16: 20 Nm
Part list
Parts Material Quantity
Package data
Product Length (mm) Width (mm) Height (mm) Weight (kg)
Product options
Tubes of various lengths and diameter can be ordered from MAFI.
EN 1090
Frot.
Mr
Fr
Vertical load
Max Supported Equipment mass Fmass = 200 kg
Axial moment
Ultimate axial moment Mr: 43249 = 1000 Nm
43248 = 350 Nm
43247 = 350 Nm Frot.
43246 = 150 Nm
Torque (Nm)
Parent Pole ø (mm)
MAFI 3263/65, 3273
48.3 178
60.3 230
76.1 298
114.3 462
MAFI 4418*
3-Sector
Antenna
Mount
—
Designed to accommodate three large
panel antennas attached to a single spine pole.
Additional features:
• Handles three large antennas.
• Flexible and easy to assemble.
40 Rev 5 *Article MAFI 4415/4418
MAFI 4418*
3-Sector
Antenna
Mount
Flexibility
The mounts will fit spine poles ranging from Ø 76 – 114.3 mm.
MAFI 4415 provides an offset of 126 mm from the equipment MAFI 4415
pole center to the face of the spine pole. Content of kit
MAFI 4418 provides an offset of 226 mm from the equipment
pole center to the face of the spine pole. The equipment poles
can be Ø 60.3 or 76.1 mm.
How to order
To order this kit, please contact MAFI quoting article number:
4418 or E-order number (SEG): 6000682
4415 or E-order number (SEG): 6000881
Contact information can be found at www.mafi.se.
MAFI 4418
Content of kit
Parent pole/leg
Ø 76 – 114.3 mm
Equipment pole
MAFI 4415
Ø 60.3 – 76.1 mm
Tightening torque
Bolts M12: 31 – 80 Nm
U-bolts M12: 31 Nm
MAFI 4418
Part list
Parts Material Quantity
Package data
Product Length (mm) Width (mm) Height (mm) Weight (kg)
Product options
Tubes of various lengths and diameter can be ordered from MAFI.
EN 1090
Ft
Fmass
Vertical load
Max Supported Equipment mass per offset tube (Fmass) = 60 kg
Ultimate Transient Person-Load (Ft )= 2.4 kN
Horizontal load
Ultimate transient horizontal load per tube (Fwind) = 4000 N
MAFI 3510
Rafter
Bracket Kit
—
Designed to provide a pole mount on to rafters or roof
trusses for tubes of Ø 60.3 – 114.3 mm.
44 Rev 2 Article MAFI 3510
MAFI 3510
Rafter
Bracket Kit
Flexibility
The product can be mounted directly on to the wooden
structure using through-mounts with large square washers on
the back. The kit consist of high quality steel parts with hot dip
galvanization treatment or from acid proof stainless steel.
How to Order
To order this kit, please contact MAFI quoting article number:
3510 or E-order number (SEG): 6000882
Contact information can be found at www.mafi.se.
Mounting structure
Equipment pole
Ø 60.3 – 114.3 mm
Tightening torque
Part list
Parts Material Quantity
Threaded rod M8 A4 14
Package data
Product Length (mm) Width (mm) Height (mm) Weight (kg)
Product options
MAFI 4328, Foot for equipment pole.
EN 1090
Fwind
FRd1
Vertical load
Ultimate Fmass resistance = 3000 N
60.3 230
76.1 298
88.9 353
101.6 408
114.3 462
MAFI 2230*
Telescopic
Strut Support
—
Designed to provide flexible bracing to a pole.
The support can be fitted as part of a new installation
or it can be retrofitted to an existing pole. All that is
required is two structural attachment points within reach
of the pole. The attachment points can be horizontal,
vertical or anything inbetween. The kit consists of a pair of
telescopic struts with feet and a pole attachment bracket.
48 Rev 1 *Article MAFI 2230/2231/2232/2233/2234/2235
MAFI 2230*
Telescopic
Strut Support
Flexibility
The 2230-family comprises three lengths of strut and two
standard sizes of pole attachment-clamp available,
to fit poles Ø 76 or 114 mm.
Please see the table on the next page.
An optional pole attachment-clamp the 3396.
Can fit poles < Ø 76 mm.
How to Order
To order this kit, please contact MAFI quoting article number:
2230 or E-order number (SEG): 6000865
2231 or E-order number (SEG): 6000866
2232 or E-order number (SEG): 6000867
Option: MAFI 4328 Content of kit
2233 or E-order number (SEG): 6000868
2234 or E-order number (SEG): 6000869
2235 or E-order number (SEG): 6000870
Contact information can be found at www.mafi.se.
© 2017 MAFI AB. All rights reserved.
*Article MAFI 2230/2231/2232/2233/2234/2235 Rev 1 49
Equipment pole
Clamp set Ø 76 mm
Tightening torque
U-bolt: 31 Nm (Ø 76 mm)
46 Nm (Ø 114 mm)
M12 screws: 80 Nm
M16 screws: 100 Nm
Clamp width
Product X Length (m)
Ø (mm)
Package data
Product Length (mm) Width (mm) Height (mm) Weight (kg)
2230/2233 1100 160 100 13.8
2231/2234 2100 160 100 20.3
2232/2235 3100 160 100 26.8
Product options
MAFI 4328, Equipment pole foot.
EN 1090
Fstrut Fstrut
Load capacity
Each strut is designed to take a maximum tension/
compression force according to below:
Ø 76 mm tube clamp: Fstrut= 10 kN
Ø 114 mm tube clamp: Fstrut = 15 kN
MAFI 4020
Single
RRU-Mount
—
Designed to provide a secure mounting solution for a
single Ericsson RRU with or withiout PSU. The Single
RRU-mount can also be used in A2 configurations.
Additional features:
• Tube and wall mounting in the same product
• Can be used in conjunction with the PSU or the A2 unit.
52 Rev 3 Article MAFI 4020
MAFI 4020
Single
RRU-Mount
Flexibility
The mount will fit any round member from
Ø 25 – 114 mm, or any equal-angle or square-section
member from 35 × 35 – 80 × 80 mm. It can also
be used for wall mounting.
How to Order
To order this kit, please contact MAFI quoting article number:
4020 or E-order number (SEG): 6000683
Contact information can be found at www.mafi.se. Content of kit
Parent pole/leg
35 × 35 mm
up to 80 × 80 mm
Ø 25 – 114 mm
35 × 35 mm
up to 80 × 80 mm
Compatible RRU-Models
Tightening torque
Part list
Parts Material Quantity
Washers FZV 16
Package data
Length (mm) Width (mm) Height (mm) Weight (kg)
EN 1090
Ftransient
Fmass
Load Resistance
Max equipment weight: 40 kg per equipment fitting
instance (Fmass ≈ 390 N).
An ultimate transient man-load of 2400 N (Ftransient)
is also accepted.
MAFI 4019-*
RRU-Mount
Family
—
Designed to provide a secure mounting solution for
two, three or four Ericsson RRUs, with or without PSU.
The double RRU mount, 4019-2, can also accomodate
a configuration with two A2 units.
Additional features:
• Easy to assemble RRU in the same level.
• Three models - Double, triple and quattro.
56 Rev 3 *Article MAFI 4019-2/3/4
MAFI 4019-*
RRU-Mount
Family
MAFI 4019-4
The 4019-3 and 4019-4 will fit any round member from
Ø 25 – 114 mm, or any equal-angle or square-section
member from 40 × 40 – 80 × 80 mm.
The 4019-2 will fit any round member from Ø 40 – 114 mm,
or any square-section member from 40 × 40 – 80 × 80 mm.
×2
Content of kit
4019-3:
40 × 40 mm up to 80 × 80 mm
4019-4:
40 × 40 mm up to 80 × 80 mm
4019-2: Ø 40 – 114 mm
4019-3: Ø 25 – 114 mm
4019-4: Ø 25 – 114 mm
MAFI 4019-2
40 × 40 mm
up to 80 × 80mm
Compatible RRU-models
Tightening torque
Package data
Product Length (mm) Width (mm) Height (mm) Weight (kg)
4019-3
4019-2 360 230 90 5.8
4019-4 EN 1090
Fmass Fmass
Fmass
Fmass
Load resistance
Max equipment weight: 35 kg per equipment fitting
instance (Fmass ≈ 345 N).
MAFI 4036
Single RRUs
Support
—
Designed to provide a secure mounting solution for one
Ericsson RRU, or two RRUs with the optional Dual RRUs
support expansion, with or without PSU or A2/A3.
60 Rev 1 *Article MAFI 4036/4037
MAFI 4036*
Single RRUs
Support
Flexibility
The support can be used on a range of pole diameters with
or without a PSU or A2/A3 attached to the backside of the
RRU. It can also be mounted on angle irons as well as box
sectional beams. The support is manufactured of high quality
steel with hot dip galvanization treatment.
How to Order
To order this kit, please contact MAFI quoting article number:
4036 or E-order number (SEG): 6000826
4037 or E-order number (SEG): 6000827
Contact information can be found at www.mafi.se.
Parent pole/leg
35 × 35 mm
up to 80 × 80 mm
Ø 35 – 114 mm
35 × 35 mm
up to 80 × 80 mm
Compatible RRU-models
Tightening torque
Package data
Product Length (mm) Width (mm) Height (mm) Weight (kg)
Product options
MAFI 4037, Dual RRUs Support expansion kit.
MAFI 6023
Multi ERS
Bracket
—
Brackets for attaching up to four Ericsson ERS equipment
i.e. RRU, PSU and/or filters to a pole in "bookshelf"
or "portrait" position.
Additional features:
• Allows up to four mountable units.
• Low weight.
• Easy installation.
64 Rev 1 Article MAFI 6023
MAFI 6023
Multi ERS
Bracket
Flexibility
The product can be mounted either as a pair
to a pole from Ø 55 – 114 mm or as singles directly
bolted to a suitable wall.
How to Order
To order this kit, please contact MAFI quoting article number:
6023 or E-order number (SEG): 6000893
Contact information can be found at www.mafi.se. Content of kit
Vertical load
Max supported equipment mass (Fmass) = 80 kg total
(40 kg per bracket).
© 2017 MAFI AB. All rights reserved.
Article MAFI 6023 Rev 1 65
×
Equipment pole
Ø 55 – 114.3 mm
Tightening torque
Part list
Parts Material Quantity
Package data
Product Length (mm) Width (mm) Height (mm) Weight (kg)
Product options
MAFI 9748; M8 flange bolts for mounting extra radios.
MAFI 5110
RRU
Support
—
Designed for attaching RRU's to existing cable trays.
Additional features:
• Flat and lightweight package.
• Suitable for most cable trays.
68 Rev 3 Article MAFI 5110
MAFI 5110
RRU
Support
Flexibility
The support is delivered as a flat pack and can easily ×2
be mounted on cable trays of width 200 – 500 mm. Content of kit
Self-tapping screws are included.
Quality
The support is manufactured from high quality steel
with hot dipped galvanization.
How to Order
To order this kit, please contact MAFI quoting article number:
5110 or E-order number (SEG): 6000687
Contact information can be found at www.mafi.se.
Parent structure
Part list
Parts Material Quantity
Bolts M10 A4 4
Washers FZV 4
Package data
Product Length (mm) Width (mm) Height (mm) Weight (kg)
Product options
MAFI 91103 ; Adaptor plate for Nokia RRH.
MAFI 1234
RRU Adaptor
Plate
—
To be used when modernizing or expanding
capacity on existing footprint. The plate allows
you to mount one face mounted or two bookshelf
mounted Ericsson RRU's. The plate also allow for
PSU mounting behind the RRU’s.
Additional features:
• Saves installation time.
• Support to modernizing old equipment.
72 Rev 1 Article MAFI 1234
MAFI 1234
RRU Adaptor
Plate
Flexibility
The adaptor plate can be mounted on MAFI products:
4010, 4015, 4020 and the 4019-family. Or on similar brackets
with same footprint.
How to Order
To order this kit, please contact MAFI quoting article number:
1234 or E-order number (SEG): 6000825
Contact information can be found at www.mafi.se.
Vertical load
Max supported equipment mass (Fmass) = 35 kg
Content of kit
Mountable products
Tightening torque
Bolt M8: 22 Nm
Bolt M10: 40 Nm
Part list
Parts Material Quantity
Package data
Product Length (mm) Width (mm) Height (mm) Weight (kg)
MAFI 3115
Antenna
Offset
—
Designed to allow for an RRU to be mounted behind
a panel antenna without any extra equipment pole.
Additional features:
• Antenna offset without poles.
• Saves weight and wind load.
76 Rev 4 *Article MAFI 3115/31154
MAFI 3115*
Antenna
Offset
Flexibility
The offset bracket can handle a wide range of tower
and mast leg sections. The bracket fits either directly
against the antenna or tilt brackets if used.
The optional 31154 antenna adapter kit allows mounting
of antennas with 150 mm c/c fixings in the vertical plane.
Parent pole/leg
Ø 25 – 76.1 mm
Tightening torque
U-bolt M12: 31 Nm
MAFI 3115
Part list
Parts Material Quantity
Package data
Product Length (mm) Width (mm) Height (mm) Weight (kg)
Product options
MAFI 31154; Antenna adapter kit.
EN 1090
Mresisting
Fwind
Vertical load
Max Supported Equipment mass = 50 kg
Ultimate Transient Man-Load = 2.4 kN
42.3 152
48.3 178
60.3 230
76.1 298
MAFI 4112
Free Stander
Light
—
Designed as a free standing equipment pole
for low wind-load generating equipment such as RRUs
placed in areas of low risk. The 4112 is assembled
on site allowing it to be carried by one man alone in
components weighing less than 25 kg.
Additional features:
• Small footprint.
• Everything in the box, including concrete blocks.
80 Rev 2 Article MAFI 4112
MAFI 4112
Free Stander
Light
Flexibility
The pole on the free stander light is tiltable up to 6°,
so that the pole will always be vertical.
How to Order
To order this kit, please contact MAFI quoting article number:
4112 or E-order number (SEG): 6062548
Contact information can be found at www.mafi.se.
Content of kit
Equipment pole
Ø 60.3 mm
Tightening torque
Threaded rods: 35 Nm
Grub screws: 10 Nm
Part list
Parts Material Quantity
Protective mat 1
Package data
Product Length (mm) Width (mm) Height (mm) Weight (kg)
Fwind
Overturning moment
For this free standing structure the critical dimensioning
parameter is the ability to resist overturning moment.
The figures in the table need to be higher than the moment
applied by the ultimate wind loads acting on the pole and
the supported equipment. A stability calculation should be
done in every case - if you need help, please contact MAFI.
Overturning
Configuration
moment MO (Nm)
MAFI 4309
Free Stander
Medium
—
Designed to carry antennas and other equipment on
places where a free standing structure is suitable.
Additional features:
• Optimized for small antennas of 3000 mm.
• All in one box.
84 Rev 5 Article MAFI 4309
MAFI 4309
Free Stander
Medium
Flexibility
The ballast in the structure can be varied to suit the wind
load and there’s a lot of space for mounting equipment.
The equipment pole is tiltable up to 6° to so that the pole
can be kept vertical.
How to Order
To order this kit, please contact MAFI quoting article number:
4309 or E-order number (SEG): 6062564 Option: 43090,
Contact information can be found at www.mafi.se. extra ballast pockets for 4309
Equipment pole
76.1 × 2.9 mm
Tightening torque
Ballast blocks
2 × 4 pcs of
500 × 500 × 50 mm concrete
blocks, each 25 kg (only
included for UK market).
Tilting
Protective mat 1
Package data
Product Length (mm) Width (mm) Height (mm) Weight (kg)
Product options
Art. no. Description
EN 1090
Fwind
Overturning resistance
For this free standing structure the critical dimensioning
parameter is the ability to resist overturning.
The figures in the table need to be higher than the moment
applied by the ultimate wind loads acting on the pole and
the supported equipment.
The roof structure should to be checked by an engineer
to confirm that it can withstand the total weight of the
structure. Also it should be confirmed that the friction
between the 4309's rubber mat and the roof is enough
to prevent sliding.
Overturning
Configuration
resistance MRd (Nm)
MAFI 4600*
Freestanding
Corner Mount
—
Designed to provide mounting opportunity
for antennas and other equipment on locations
where freestanding solutions are needed.
Additional features:
• Several different sizes depending on the roof
and antenna load.
• Suitable for different sizes of concrete blocks.
88 Rev 3 *Article MAFI 4600/4601/4602
MAFI 4600*
Freestanding
Corner Mount
Flexibility
The structure is designed to support equipment-carrying
tubes using ballast as counter weight. This provides mounting
oportunity without penetrating weatherproofing layers on
rooftops. Adjustable ballast-carrying cross beams make
it possible to account for different sizes of concrete blocks
depending on availabillity. The interface between the frame
and the equipment pole is a cone-shaped folded steel sheet
that provides a three point contact even when tilting so that
the pole can be kept vertical if the surface is sloping.
MAFI 4602 MAFI 4600
Detailed design data
Detailed design data for this product
can be found at www.mafi.se.
How to Order
To order this kit, please contact MAFI quoting article number:
4600 or E-order number (SEG): 6000689
4601 or E-order number (SEG): 6000690
4602 or E-order number (SEG): 6000691
Contact information can be found at www.mafi.se.
Equipment pole
Ø 76.1 mm
Tightening torque
View mounting
instructions.
Part list
Parts Material Quantity Tightening torque
Sheet steel parts S355MC FZV -
Recommended
Frame side tubes S355J2H FZV 4
maximum tilt: 4°.
Nuts and bolts 8.8 FZV or equivalent -
Package data
Product Length (mm) Width (mm) Height (mm) Weight (kg)
Product options
MAFI 42071: 500 × 500 × 50 mm, 25 kg concrete block.
MAFI 91124: Additional strut for yoke arms to be attached to Ø 76.1 mm tube.
Tubes of various lengths and diameter can be ordered from MAFI.
EN 1090
Overturning resistance
For this family of freestanding structures the critical
dimensioning parameter is the ability to resist overturning.
The figures in the overturning moment table need to be higher
than the moment applied by the design wind loads
(i.e ultimate load including load factors) acting on the pole
and the supported equipment.
The roof structure should be checked by an engineer to
confirm that it can withstand the total weight of the structure.
Also it should be confirmed that the friction between the
product´s rubber mat and the roof is enough to prevent sliding.
MAFI 91110
Extra
Pole Kit
—
Designed to provide mounting opportunity
for an extra pole on the freestanding corner
mounts MAFI 4601 and 4602.
92 Rev 1 Article MAFI 91110
MAFI 91110
Extra
Pole Kit
MAFI 91110
mounted on 4601
Flexibility
Kit for mounting an extra 76.1 mm tube to MAFI 4601 or 4602.
The recommended length of the tube is max 1.5 m.
Easily mounted when assembling the freestanders corner
mounts or added onto already built structures.
How to Order
To order this kit, please contact MAFI quoting article number: MAFI 91110
91110 mounted on 4602
Contact information can be found at www.mafi.se.
Content of kit
Equipment pole
Ø 76.1 mm
Tightening torque
Part list
Parts Material Quantity
Package data
Product Length (mm) Width (mm) Height (mm) Weight (kg)
EN 1090
MAFI 8050
Adjustable
Cabinet
Platform
—
Lightweight platform designed to provide a level base
for small and medium-sized cabinets.
Additional features:
• Flexible hole pattern fits most cabinets.
• All in one box.
96 Rev 1 *Article MAFI 8050/8051
MAFI 8050*
Adjustable
Cabinet
Platform
MAFI 8051
Flexibility
Because of the elongated holes and slidable cross beams
you can create the hole pattern you need for any cabinet.
The frame can be placed on either the supplied ball-jointed
feet, or directly on the roof/ground.
Using the ball-jointed feet allows you to compensate
for a maximum roof slope of 6°. Outriggers can also be
specified in lengths of 1500 mm or 2000 m
(called MAFI 91100 and MAFI 91101 respectively).
How to Order
To order this kit, please contact MAFI quoting article number:
8050
8051 or E-order number (SEG): 6000692
Contact information can be found at www.mafi.se.
Maximum M12
Ground/Roof slope
Maximum: 6°
Equipment weight
Maximum: 600 kg
Tightening torque
Bolt M12: 80 Nm
Part list
Quantity Quantity
Parts Material
8050 8051
Protective mats 4 4
Package data
Product Length (mm) Width (mm) Height (mm) Weight (kg)
Product options
MAFI 91100: Outriggers, 1500 mm.
Fwind
Mresisting
Overturning moment
When designing a platform, you need to ensure that the frame
is wide enough to provide stability against overturning.
You need to know the wind forces at the site location and
the dimensions and weight of the cabinets.
A stability calculation should be done in every case
– if you need help, please contact MAFI.
MAFI 3541
Medium Duty
Wall Mount
—
Designed for mounting an equipment pole on a wall.
The kit is dimensioned to carry medium-weight tubes
and equipment mounted between the wall brackets.
The kit consists of a pair of brackets with all
necessary U-bolts.
Additional features:
• Small wall bracket with the equipment near the wall.
• Few parts and easy assemble.
100 Rev 3 Article MAFI 3541
MAFI 3541
Medium
Duty Wall
Mount
Flexibility
The product can be mounted either directly to brick
or concrete walls, or using through-mounts with back plates.
Equipment poles can range from Ø 60 – 114 mm.
Equipment pole
Ø 60 – 114.3 mm
Tightening torque
U-bolts: 15 Nm
Part list
Parts Material Quantity
Package data
Product Length (mm) Width (mm) Height (mm) Weight (kg)
Product options
Tubes of various lengths and diameter can be ordered from MAFI.
EN 1090
Fmass
Vertical load
Max Supported Equipment mass = 100 kg
Reaction force
Ultimate lateral reaction force (Flat) : 1200 N per bracket
60.3 115
76.1 159
88.9 176
101.6 204
114.3 231
MAFI 2414
Heavy Duty
Wall Mount
—
Designed to provide a pole mount on a wall.
The product is dimensioned to carry heavy poles
and equipment.
Additional features:
• For heavy duty wall installations.
104 Rev 3 Article MAFI 2414
MAFI 2414
Heavy
Duty Wall
Mount
Flexibility
The product can be mounted either directly bolted
to brick or concrete walls or using through-mounts
with reinforcement on the back.
How to Order
To order this kit, please contact MAFI quoting article number:
Content of kit
2414 or E-order number (SEG): 6000693
Contact information can be found at www.mafi.se.
Mounting structure
Equipment pole
Tightening torque
U-bolts M12: 31 Nm
Bolts M16: 150 Nm
Part list
Parts Material Quantity
Package data
Product Length (mm) Width (mm) Height (mm) Weight (kg)
Product options
Tubes of various lengths and diameter can be ordered from MAFI.
EN 1090
Configuration 1
Fmass
101.6 816
114.3 924
MAFI 3544
Large Offset
Wall Mount
—
Designed for mounting an equipment pole on a wall when
a large clearance is required. The product is dimensioned
to carry medium-weight tubes and equipment mounted
between the wall brackets. The kit consists of a pair of
brackets with all necessary U-bolts.
Additional features:
• Small wall bracket with the equipment
distanced from the wall.
• Few parts and easy assemble.
108 Rev 2 Article MAFI 3544
MAFI 3544
Large
Offset Wall
Mount
Flexibility
The product can be mounted either directly to brick or concrete
walls, or using through-mounts with back plates.
Equipment poles can range from Ø 60 – 114 mm.
How to Order
To order this kit, please contact MAFI quoting article number:
3544 or E-order number (SEG): 6062518
Contact information can be found at www.mafi.se.
Content of kit
Equipment pole
Ø 60 – 114.3 mm
Tightening torque
U-bolts: 23 Nm
Part list
Parts Material Quantity
Package data
Product Length (mm) Width (mm) Height (mm) Weight (kg)
Product options
Tubes of various lengths and diameter can be ordered from MAFI.
EN 1090
Fmass
Vertical load
Max Supported Equipment mass = 100 kg
60.3 172
76.1 223
88.9 264
101.6 306
114.3 346
MAFI 43692
Corner
Wall Mount
—
Designed to provide a pole mount at the corner of a wall
with a clearance of 50 mm. The product is dimensioned
to carry medium-weight tubes and equipment mounted
between the wall brackets. The kit consists of a pair of
brackets with all necessary U-bolts.
Additional features:
• Corner wall bracket.
• Offset a pole from the corner of a wall.
112 Rev 3 Article MAFI 43692
MAFI 43692
Corner Wall
Mount
Flexibility
The product can be mounted either directly to brick or concrete
walls, or using though-mounts with back plates.
Equipment poles can range from Ø 60 – Ø 114 mm.
Equipment pole
Ø 60 – 114.3 mm
Tightening torque
U-bolts M12: 31 Nm
Part list
Parts Material Quantity
Package data
Product Length (mm) Width (mm) Height (mm) Weight (kg)
Product options
Tubes of various lengths and diameter can be ordered from MAFI.
EN 1090
Fmass
Reaction force
Ultimate lateral reaction force (Flat) : 2300 N per bracket
60.3 230
76.1 298
88.9 353
101.6 408
114.3 462
MAFI 7000
Stainless
Steel 10-hole
Earthbar
—
Designed to be used as an earthbar for towers
and feeder runs.
116 Rev 2 Article MAFI 7000
MAFI 7000
Stainless
Steel 10-hole
Earthbar
Flexibility
The earthbar can easily be fitted to round members from
Ø 42 – 76 mm or angle members up to 50 × 50 mm.
It can also be readily attached to cable ladder,
cable tray and C-channel members.
How to Order
To order this kit, please contact MAFI quoting article number:
7000 or E-order number (SEG): 6062665
Contact information can be found at www.mafi.se.
Parent pole/leg
Ø 42 – 76 mm
Rail ancor:
Inner dimension: < 49 mm
Part list
Parts Material Quantity
Plate A2 1
U-bolt A4 1
Bolts M8, M6 A2 12
Nuts M8 A2 10
Washers M8, M6 A2 34
Package data
Product Length (mm) Width (mm) Height (mm) Weight (kg)
MAFI 32655*
Cable Holder
Family
—
Designed as an easily-fitted tower-leg clamp
to accommodate a number of feeder cables.
120 Rev 2 Article MAFI 32655/32657/32658/32660/32663/32664
MAFI 32655*
Cable Holder
Family
Flexibility
The different models in the family can accommodate
MAFI 32655/57/58
tubular tower-legs ranging from Ø 20 – 192 mm,
and angle legs from 60 × 60 – 130 × 130 mm.
How to Order
To order this kit, please contact MAFI quoting article number:
32655 or E-order number (SEG): 6062533 MAFI 32660/63
32657 or E-order number (SEG): 6000695
32658 or E-order number (SEG): 6000696
32660 or E-order number (SEG): 6062534
32663 or E-order number (SEG): 6000697
32664 or E-order number (SEG): 6000698
Contact information can be found at www.mafi.se.
MAFI 32664
Parent pole/leg
32655 Ø 20 – 50 mm
32657 Ø 40 – 76 mm
32658 Ø 89 – 114 mm
32660 Ø 35 – 76 mm
32663 Ø 89 – 114 mm
32664 Ø 76 – 192 mm
Tightening torque
Part list
Parts Material Quantity*
Package data
Product Length (mm) Width (mm) Height (mm) Weight (kg)
Tubes,
Components
& Various
Accessories
—
124 Rev 2 Tubes and Components
Tubes and
Components
—
The MAFI range of tubes can be ordered in different standard
lengths. The tables below contain information about material,
dimensions and weight.
Order by entering article number with the appendix
indicating the length.
Ex: GT60329-20
GT60329-20: Galvanized Tube.
GT60329-20: Outer Ø: 60.3 mm and wall thickness: 2.9 mm.
GT60329-20: Length: 2000 mm.
GT60329-xx 60.3 2.90 4.11 -10, -15, -20, -25, -30, -60
GT76129-xx 76.1 2.90 5.24 -075, -10, -15, -20, -25, -30, -40, -60
GT88932-xx 88.9 3.20 6.76 -10, -15, -20, -25, -30, -60
GT114336-xx 114.3 3.60 9.83 -075, -10, -15, -20, -30, -40, -60
GT114350-xx 114.3 5.00 13.51 -10, -15, -20, -30, -40, -60
AT605-xx 60.0 5.00 2.33 -10, -15, -20, -25, -30, -60
GB50503-xx 50 × 50 3,00 4.32 -07, -10, -12, -15, -20, -30, -60
Ø
Thread U-bolts
C-C Effective
Article no. Type length The MAFI range of U-bolts are made of 8.8 FZV
(mm) (metric) length (mm)
(mm) or A4 steel. They range in size and shape to fit
3756-1 A 70 M8 45 50 different member profiles. The U-bolt kits in
the table below include nuts and washers.
3013-1 B 90 M8 95 107
Order by entering the article number.
2802-1 A 81 M10 85 95
3011-1 B 90 M10 70 77
33802-1 A 49 M12 60 112
3380-1 A 62 M12 55 75
33801-1 A 74 M12 60 125
2638-1 A 76 M12 75 88
33803-1 C 74 M12 60 154
2801-1 A 92 M12 91 97
33804-1 A 103 M12 110 150
2867-1 A 130 M12 102 108
3572-1 A 144 M12 100 120
2637-1 A 134 M16 60 111 Type A Type B Type C
Various
Accessories
Top-hat Pole Covers
Designed as a waterproof cover for the top of a pole.
To order this kit, please contact MAFI quoting article number:
43971/43972/4397.
Contact information can be found at www.mafi.se.
Plate
Article no. Article description Hole dim. (mm)
dim.(mm)
Lightning Protector
Designed to protect equipment poles from lightning current
To order this kit, please contact MAFI quoting article number:
4274/439711/439720/43970.
Contact information can be found at www.mafi.se.
Lenght
Article no. Article description Bolts (metric)
(mm)
Europe
MAFI AB
Örjasvägen 4 Box 275
SE-792 24 Mora, Sweden
Tel: +46 (0)250-381 60
Overall e-mail adress: info@mafi.se
Order e-mail adress: order@mafi.se
Personell: firstname.lastname@mafi.se
www.mafi.se