Академический Документы
Профессиональный Документы
Культура Документы
TABLE OF CONTENTS
# Description Page No
CONSULTANT
Approved
Rev no Date Doc No Rev Note Prep. By Chekd. By
by
R0 19.10.2015 KETAN MANJULA MSN
STRUCTURAL DESIGN OF 80M GROUND BASED
SQUARE ANGULAR TOWER WITH WIND SPEED 144 KMPH
REPORT PREPARED BY
CONSULTANT
7 FOUNDATION ................................................................................................................... 15
7.1 FOUNDATION LOADS FOR EXISTING ANTENNA ...................................................... 15
8 RECOMMENDATIONS ...................................................................................................... 16
8.1 OVERVIEW .................................................................................................................... 16
8.2 UPGRADE METHOD ..................................................................................................... 16
3
PROJECT: 80MGBT 144 KMPH(NAMASHESHE) DATE REV DESIGN KETAN
4
PROJECT: 80MGBT 144 KMPH(NAMASHESHE) DATE REV DESIGN KETAN
The tower situated at coordinates S14.87231, E024.61439 was modeled and loaded as
defined in paragraph 3.1. Summary of the structural analysis results for the tower with
the existing loading is shown in paragraph 5. The current tower is overloaded with the
existing antenna loading. Strengthening is required.
Foundation analysis was done with the dimensions provided and it is found SAFE.
2 ANALYSIS INTRODUCTION
This report covers the structural analysis with an overall height of 80Mhigh, 4 legged
self-supporting angular tower (Site Coordinates S14.87231, E024.61439). The tower
was analyzed in accordance with the TIA_222G code. The tower consists of profile legs
and diagonal, horizontal bracing sizes of varying sizes as listed in paragraph 3.2. The
bracing members are bolted to the legs with bolt connections. The data was analyzed
using PLS TOWER software. The purpose of the analysis is to make an assessment of
the structural adequacy of both the steel tower and concrete foundation under the
current loading conditions. The tower deflection was checked based on a maximum
allowable rotation of the microwave dishes of 0.5 degrees. This is the limit generally
accepted by the telecommunication industry. The constraint reactions were used to
check the existing foundation for the tower.
2.1 ASSUMPTIONS
The ladder cage starts at 4m from the base of the tower and this section has a
lower wind loading factor than the full ladder configuration fitted with safety
cage. For the purposes of calculation the ladder is treated as uniform, with
safety cage, and commences 2m from the base of the tower.
The crest height determination and land profile selection is made to consider
the worst case condition
The full FPA is considered in all calculations; no allowance is made for
shielding.
5
PROJECT: 80MGBT 144 KMPH(NAMASHESHE) DATE REV DESIGN KETAN
NOTE:
1. The above body wind calculations and antenna loading calculations furnished above
pertains to the Load Case of 1.D+1.0Dg+1.0Wo
2. The calculations for other load combinations have not been furnished in this report but have
been duly considered in the design.
(As shown in Index of Loads & Load combinations).
8
PROJECT: 80MGBT 144 KMPH(NAMASHESHE) DATE REV DESIGN KETAN
L 32 D 32 L5 SAE 1 5 0 * 1 5 0 *15 D 22
1 N 0 -Ø 2 .4M M /W H 31 1 N 0 -Ø 1 .8M M /W
L6 SAE 1 5 0 * 1 5 0 *15 D 23 D AE 5 0 * 5 0 *5D
P A R A B O L IC D IS H P A R A B O L IC D IS H L7 SAE 1 5 0 * 1 5 0 *15 D 24 D AE 5 0 * 5 0 *5D
D 31 D AE 5 0 * 5 0 *5D
L 31 L8 SAE 1 5 0 * 1 5 0 *12 D 25
H 30 L9 SAE 1 5 0 * 1 5 0 *12 D 26 D AE 5 0 * 5 0 *5D
L1 0 SAE 1 5 0 * 1 5 0 *12 D 27 D AE 5 0 * 5 0 *5D
6 N O s.-G S M A N T E N N A
D 30 (2 .2 5 M X 0.26M )
L 11 D 11 D 11
N E E D S T O B E S TR E N G TH E N E D
H 10 1 N o.-Ø 1 .2 M M /W P A R A B O L IC D IS H PL A C ED A T 78.0M .
L 10 D 10 D 10 1 N o.-Ø 2 .4 M M /W P A R A B O L IC D IS H PL A C ED A T 76.0M .
N E E D S T O B E S TR E N G TH E N E D
H9 1 N o.-Ø 1 .8 M M /W P A R A B O L IC D IS H PL A C ED A T 76.0M .
L9 6 N o s-G S M A N TE N N A (2 .2 5M x0 .2 6M ) PLA C ED A T 74.0M .
D9 L 9, D9
N E E D S T O B E S TR E N G TH E N E D 1 N o.-Ø 2 .4 M M /W P A R A B O L IC D IS H PL A C ED A T 70.0M .
H8
1 N o.-Ø 1 .2 M M /W P A R A B O L IC D IS H PL A C ED A T 70.0M .
D8 L8 1 N o.-Ø 1 .8 M M /W P A R A B O L IC D IS H PL A C ED A T 68.0M .
L8 N E E D S T O B E S TR E N G TH E N E D
H7 1 N o.-Ø 1 .2 M M /W P A R A B O L IC D IS H PL A C ED A T 68.0M .
D7
L 7, D7
L7 N E E D S T O B E S TR E N G TH E N E D
H6
D6
L6 L 6, D6
N E E D S T O B E S TR E N G TH E N E D
H5
D5
L 5, D5
L5 N E E D S T O B E S TR E N G TH E N E D
H4
D4
L 4, D4
L4 N E E D S T O B E S TR E N G TH E N E D
H3
D3
L 3, D3
L3 N E E D S T O B E S TR E N G TH E N E D
H2
D2
L 2, D2
L2 N E E D S T O B E S TR E N G TH E N E D
H1
L1 D1 L 1, D1
N E E D S T O B E S TR E N G TH E N E D
ZM 3 4 1 4
9
PROJECT: 80MGBT 144 KMPH(NAMASHESHE) DATE REV DESIGN KETAN
The parameters below are required as input for the determination of the loads. These
parameters are described within the TIA_222G.
10
PROJECT: 80MGBT 144 KMPH(NAMASHESHE) DATE REV DESIGN KETAN
A finite element analysis was run on the structure, the results are tabulated below.
Compres Length
Group Steel Comp. sion of Curve FOS Tensile Tension FOS No.of
Description Angle Type Angle Size Strength Force Comp. Load case Capacity L/R member No. (Comp) Force Tension Load case Capacity (Tens) Bolts
(MPa) (kN) (kN) (m) (kN) (kN)
L1 SAE 150*150*15 300 -1182.54 4: 1.2D + 1.0Dg + 1.6Wo 861.91 68.42 4.01 1 0.73 1080.06 5: 0.9D + 1.0Dg + 1.6Wo 1161.00 1.07 16
L2 SAE 150*150*15 300 -1119.48 4: 1.2D + 1.0Dg + 1.6Wo 861.91 68.42 4.01 1 0.77 1020.24 5: 0.9D + 1.0Dg + 1.6Wo 1161.00 1.14 16
L3 SAE 150*150*15 300 -1055.30 4: 1.2D + 1.0Dg + 1.6Wo 861.91 68.42 4.01 1 0.82 958.84 5: 0.9D + 1.0Dg + 1.6Wo 1161.00 1.21 16
L4 SAE 150*150*15 300 -989.88 4: 1.2D + 1.0Dg + 1.6Wo 861.91 68.42 4.01 1 0.87 896.74 5: 0.9D + 1.0Dg + 1.6Wo 1161.00 1.29 16
L5 SAE 150*150*15 300 -923.23 4: 1.2D + 1.0Dg + 1.6Wo 861.91 68.42 4.01 1 0.93 834.17 5: 0.9D + 1.0Dg + 1.6Wo 1161.00 1.39 16
L6 SAE 150*150*15 300 -855.48 4: 1.2D + 1.0Dg + 1.6Wo 861.91 68.42 4.01 1 1.01 770.82 5: 0.9D + 1.0Dg + 1.6Wo 1161.00 1.51 16
L7 SAE 150*150*15 300 -786.99 4: 1.2D + 1.0Dg + 1.6Wo 861.91 68.42 4.01 1 1.1 706.30 5: 0.9D + 1.0Dg + 1.6Wo 1161.00 1.64 16
L8 SAE 150*150*12 300 -752.10 4: 1.2D + 1.0Dg + 1.6Wo 703.13 67.5 2.005 1 0.93 674.55 5: 0.9D + 1.0Dg + 1.6Wo 939.60 1.39 16
L9 SAE 150*150*12 300 -716.82 4: 1.2D + 1.0Dg + 1.6Wo 703.13 67.5 2.005 1 0.98 642.89 5: 0.9D + 1.0Dg + 1.6Wo 939.60 1.46 16
L10 SAE 150*150*12 300 -682.42 4: 1.2D + 1.0Dg + 1.6Wo 703.13 67.5 2.005 1 1.03 611.53 5: 0.9D + 1.0Dg + 1.6Wo 939.60 1.54 16
L11 SAE 150*150*12 300 -647.43 4: 1.2D + 1.0Dg + 1.6Wo 703.13 67.5 2.005 1 1.09 579.89 5: 0.9D + 1.0Dg + 1.6Wo 939.60 1.62 16
L12 SAE 150*150*12 300 -613.81 4: 1.2D + 1.0Dg + 1.6Wo 703.13 67.5 2.005 1 1.15 549.14 5: 0.9D + 1.0Dg + 1.6Wo 939.60 1.71 16
L13 SAE 150*150*12 300 -579.42 4: 1.2D + 1.0Dg + 1.6Wo 703.13 67.5 2.005 1 1.21 517.91 5: 0.9D + 1.0Dg + 1.6Wo 939.60 1.81 16
L14 SAE 150*150*12 300 -546.29 4: 1.2D + 1.0Dg + 1.6Wo 703.13 67.5 2.005 1 1.29 487.83 5: 0.9D + 1.0Dg + 1.6Wo 939.60 1.93 16
L15 SAE 150*150*12 300 -512.40 4: 1.2D + 1.0Dg + 1.6Wo 703.13 67.5 2.005 1 1.37 457.33 5: 0.9D + 1.0Dg + 1.6Wo 939.60 2.05 16
L16 SAE 150*150*10 300 -479.75 4: 1.2D + 1.0Dg + 1.6Wo 575.28 67.27 2.005 1 1.2 427.57 5: 0.9D + 1.0Dg + 1.6Wo 788.40 1.84 16
L17 SAE 150*150*10 300 -446.48 4: 1.2D + 1.0Dg + 1.6Wo 575.28 67.27 2.005 1 1.29 397.45 5: 0.9D + 1.0Dg + 1.6Wo 788.40 1.98 16
L18 SAE 150*150*10 300 -414.50 4: 1.2D + 1.0Dg + 1.6Wo 575.28 67.27 2.005 1 1.39 368.26 5: 0.9D + 1.0Dg + 1.6Wo 788.40 2.14 16
L19 SAE 120*120*12 300 -381.64 4: 1.2D + 1.0Dg + 1.6Wo 467.29 85.31 2.005 1 1.22 338.42 5: 0.9D + 1.0Dg + 1.6Wo 742.50 2.19 12
L20 SAE 120*120*12 300 -350.02 4: 1.2D + 1.0Dg + 1.6Wo 467.29 85.31 2.005 1 1.34 309.59 5: 0.9D + 1.0Dg + 1.6Wo 742.50 2.40 12
L21 SAE 120*120*10 300 -316.97 4: 1.2D + 1.0Dg + 1.6Wo 395.77 84.95 2.005 1 1.25 279.55 5: 0.9D + 1.0Dg + 1.6Wo 626.40 2.24 12
L22 SAE 120*120*10 300 -302.80 4: 1.2D + 1.0Dg + 1.6Wo 395.77 84.95 2.005 1 1.31 266.74 5: 0.9D + 1.0Dg + 1.6Wo 626.40 2.35 12
L23 SAE 120*120*10 300 -269.02 4: 1.2D + 1.0Dg + 1.6Wo 395.77 84.95 2.005 1 1.47 236.25 5: 0.9D + 1.0Dg + 1.6Wo 626.40 2.65 12
L24 SAE 100*100*12 300 -240.51 4: 1.2D + 1.0Dg + 1.6Wo 309.29 103.34 2.005 1 1.29 208.57 5: 0.9D + 1.0Dg + 1.6Wo 610.20 2.93 12
L25 SAE 100*100*10 300 -204.42 4: 1.2D + 1.0Dg + 1.6Wo 260.03 103.34 2.005 1 1.27 176.73 5: 0.9D + 1.0Dg + 1.6Wo 513.00 2.90 12
L26 SAE 100*100*10 300 -175.42 4: 1.2D + 1.0Dg + 1.6Wo 260.03 103.34 2.005 1 1.48 148.63 5: 0.9D + 1.0Dg + 1.6Wo 513.00 3.45 12
L27 SAE 100*100*8 300 -136.66 4: 1.2D + 1.0Dg + 1.6Wo 212.23 102.81 2.005 1 1.55 115.36 5: 0.9D + 1.0Dg + 1.6Wo 415.80 3.60 12
L28 SAE 100*100*8 300 -107.55 4: 1.2D + 1.0Dg + 1.6Wo 212.23 102.81 2.005 1 1.97 89.59 5: 0.9D + 1.0Dg + 1.6Wo 415.80 4.64 12
L29 SAE 90*90*6 300 -70.67 4: 1.2D + 1.0Dg + 1.6Wo 122.45 114.56 2.005 1 1.73 63.18 5: 0.9D + 1.0Dg + 1.6Wo 283.50 4.49 12
L30 SAE 90*90*6 300 -49.37 4: 1.2D + 1.0Dg + 1.6Wo 122.45 114.56 2.005 1 2.48 40.22 5: 0.9D + 1.0Dg + 1.6Wo 283.50 7.05 12
L31 SAE 90*90*6 300 -24.36 1: 1.2D + 1.0Dg + 1.6Wo 122.45 114.56 2.005 1 5.03 16.68 5: 0.9D + 1.0Dg + 1.6Wo 283.50 17.00 12
L32 SAE 90*90*6 300 -8.16 1: 1.2D + 1.0Dg + 1.6Wo 122.45 114.56 2.005 1 15.01 7.33 8: 0.9D + 1.0Dg + 1.6Wo 283.50 38.70 12
L33 SAE 90*90*6 300 -2.62 7: 1.2D + 1.0Dg + 1.6Wo 122.93 114.29 2 1 46.97 1.64 2: 0.9D + 1.0Dg + 1.6Wo 283.50 172.97 12
11
PROJECT: 80MGBT 144 KMPH(NAMASHESHE) DATE REV DESIGN KETAN
12
PROJECT: 80MGBT 144 KMPH(NAMASHESHE) DATE REV DESIGN KETAN
13
PROJECT: 80MGBT 144 KMPH(NAMASHESHE) DATE REV DESIGN KETAN
Group Description Angle Type Angle Size Steel Strength LENGTH QTY
(MPa) M NOS
L1 SAE 150*150*15 300 4.010 4
L2 SAE 150*150*15 300 4.010 4
L3 SAE 150*150*15 300 4.010 4
L4 SAE 150*150*15 300 4.010 4
L5 SAE 150*150*15 300 4.010 4
L6 SAE 150*150*15 300 4.010 4
L8 SAE 150*150*12 300 2.005 4
L9 SAE 150*150*12 300 2.005 4
D1 DAE 50*50*5D 300 6.190 8
D2 DAE 50*50*5D 300 6.042 8
D3 DAE 50*50*4D 300 5.897 8
D4 DAE 50*50*4D 300 5.755 8
D5 DAE 50*50*4D 300 5.615 8
D6 DAE 50*50*4D 300 5.480 8
D7 DAE 50*50*4D 300 5.348 8
D9 DAE 50*50*5D 300 3.818 8
D10 DAE 50*50*5D 300 3.735 8
D11 DAE 50*50*5D 300 3.653 8
D12 DAE 50*50*4D 300 3.571 8
D13 DAE 50*50*4D 300 3.490 8
D14 DAE 50*50*4D 300 3.411 8
D15 DAE 50*50*4D 300 3.332 8
14
PROJECT: 80MGBT 144 KMPH(NAMASHESHE) DATE REV DESIGN KETAN
7 FOUNDATION
MAGNITUDE
FORCE LOAD CASE
(kN)
Maximum factored Compression 4: 1.2D + 1.0Dg + 1.6Wo 1240.34
Maximum factored Uplift 5: 0.9D + 1.0Dg + 1.6Wo 1136.63
Foundation analysis was done with the dimensions provided and it is found SAFE.
15
PROJECT: 80MGBT 144 KMPH(NAMASHESHE) DATE REV DESIGN KETAN