Академический Документы
Профессиональный Документы
Культура Документы
H21
Digital Copier
DP-2000/2500/3000
3
Table of Contents
7.7. Stand for 1-4 Paper Tray Options and Supplies ............................ 596
Configuration ........................................504
9.1. Installing the Electronic Sorting Board
7.8. Cartridge Unit........................................506 (DA-ES200) [For DP-2000 only]........... 596
7.9. Paper Tray ............................................509 9.2. Installing the Fax Communication Kit
7.10. Drive Unit ..............................................511 (DA-FG230).......................................... 597
7.11. Fuser Unit .............................................513 9.3. Installing the 2nd G3 Fax
Communication Port Kit (DA-FG231) ... 602
7.12. Paper Feed Module ..............................516
9.4. Installing the 10/100 Ethernet Interface /
7.13. Paper Transportion ...............................519
Internet Fax Kit (DA-NE200) ................ 605
7.14. Paper Transport Unit ............................522
9.5. Installing the Handset Kit
7.15. Automatic Duplex Unit ..........................524 (UE-403171/UE-403172) and
7.16. Dual-Path Exit Guide Unit.....................526 the Handset Mounting Kit
(UE-408004-AU) .................................. 608
7.17. Inverting Automatic Document
Feeder (1/3) ..........................................528 9.6. Installing the Parallel Port Interface Kit
(DA-PC200).......................................... 612
7.18. Inverting Automatic Document
Feeder (2/3) ..........................................531 9.7. Installing the PCL6 Emulation Kit
(DA-PC210).......................................... 614
7.19. Inverting Automatic Document
Feeder (3/3) ..........................................534 9.8. Installing the Sorting Image Memory
8/16/128 MB (DA-SM08B/16B/28B)..... 616
7.20. PC Boards/ Harnesses .........................537
9.9. Installing the Expansion Flash Memory
7.21. 1-Bin Finisher (1/9) ...............................541
Card 4/8 MB (UE-410047/410048) ...... 618
7.22. 1-Bin Finisher (2/9) ...............................543
9.10. Installing the Platen Cover
7.23. 1-Bin Finisher (3/9) ...............................545 (DA-UC200) ......................................... 619
7.24. 1-Bin Finisher (4/9) ...............................547 9.11. Installing the Automatic Document
7.25. 1-Bin Finisher (5/9) ...............................550 Feeder and the Inverting Automatic
Document Feeder (DA-AS200/AR250) 620
7.26. 1-Bin Finisher (6/9) ...............................552
9.12. Installing the Stand for 1-Paper Tray
7.27. 1-Bin Finisher (7/9) ...............................554
Configuration (DA-DA200-PA) ............. 626
7.28. 1-Bin Finisher (8/9) ...............................556
9.13. Installing the Stand for 2-Paper Tray
7.29. 1-Bin Finisher (9/9) ...............................558 Configuration (DA-DA210-PA) ............. 628
7.30. Packing and Accessories......................560 9.14. Installing the 3rd Paper Feed Module
7.31. 1-Bin Finisher Packing and and the Stand for 3-Paper Tray
Accessories ..........................................562 Configuration
(DA-DS210/DS215, DA-DA220-PA) .... 630
7.32. 2nd/3rd/4th Paper Feed Module ...........564
9.15. Installing the 2nd/4th Paper Feed
7.33. ADF Packing and Accessories .............567
Module (DA-DS200)
7.34. Automatic Document Feeder (1/3)........569 [For DP-2000/2500 Only] and the
7.35. Automatic Document Feeder (2/3)........572 Stand for 4-Paper Tray Configuration
(DA-DA230-PA).................................... 633
7.36. Automatic Document Feeder (3/3)........575
9.16. Installing the 2nd/4th Paper Feed
7.37. PCL6 Emulation Kit...............................577
Module and the Stand for 4-Paper Tray
7.38. 10/100 Ethernet Interface/Internet Configuration
Fax Kit...................................................579 (DA-DS205, DA-DA230-PA) ................ 637
7.39. Fax Communication Kit.........................581 9.17. Installing the Plain Stand
7.40. Parallel Port Interface Kit ......................585 (DA-D250) : For USA only.................... 641
7.41. Stands for USA .....................................587 9.18. Installing the Base Plate with Casters
(DA-D200) : For USA only.................... 643
Installation.............................................. 589 9.19. Installing the Plain Cabinet
(DA-DE200) : For USA only ................ 646
8.1. Precautions During Set Up ...................589
9.20. Installing the Dual-Path Exit Guide Unit
8.2. Unpacking.............................................589
(DA-FK200) .......................................... 650
8.3. Installation Procedure ...........................589
9.21. Installing the Paper Transport Unit
8.4. Adjustment............................................593 (DA-FK210) .......................................... 655
4
Table of Contents
9.22. Installing the Automatic Duplex Unit 12.11.CCD PC Board (DP-3000) ................... 882
(DA-MD200)..........................................658 12.12.CST2 PC Board (DP-2000/2500) ......... 883
9.23. Installing the Exit Tray [Inner] 12.13.CST2 PC Board (DP-3000) .................. 884
(DA-XN200) ..........................................664
12.14.CST3 PC Board (DP-2000/2500) ......... 885
9.24. Installing the Exit Tray [Outer]
(DA-XT200)...........................................666 12.15.CST3 PC Board (DP-3000) .................. 889
5
1 Specifications Table
1.1. Copy Function
Description
Items Remarks
DP-2000 DP-2500 DP-3000
Basic Specifications
1 Type Desktop
2 Platen Fixed
3 Original Position Left / Inner
4 Recording Paper Path Center
5 Face Up / Face Down Face Down
6 Drum Organic Photo Conductor (OPC)
7 Copy Process Dry Electrostatic System
Magnetic Mono Component Development
8 Developing Process
System
9 Toner Recycle No
10 Fusing System Heat & Pressure
Ledger (11" x 17") /
11 Max Original Size
A3 (297 x 420 mm)
12 Paper Size
LDR, LGL, LTR, LTR-R, INV, INV-R for USA and Canada
Paper Tray A3, A4, A4-R, A5, A5-R, B4 for EU
A3, A4, A4-R, A5, B4, B5, B5-R for Other Countries
LDR, LGL, LTR, LTR-R, INV, INV-R for USA and Canada
Bypass A3, A4, A4-R, A5, A5-R, B4 for EU
A3, A4, A4-R, A5, B4, B5, B5-R for Other Countries
Bypass Envelope No
Approx. 45
13 Warm-up Time Approx. 35 sec. 68 °F (20 °C)
sec.
From Platen/ Letter/ A4
Portrait/ 1st Paper Tray.
14 First Copy Time 4.5 sec. 3.8 sec.
Period between Start Key is
pressed and Paper exit.
15 Copy Speed
Ledger / A3 TBD TBD TBD
Legal / B4, FLS TBD TBD TBD
Letter-R / A4-R TBD TBD TBD
LTR / A4 20 cpm 25 cpm 30 cpm
Invoice / A5 TBD TBD TBD
16 Zoom
Enlargement Selected Original size / Copy size
Reduction Selected Original size / Copy size
Zoom 25 - 400% 1% Step
6
Description
Items Remarks
DP-2000 DP-2500 DP-3000
17 Paper Feed Front loading universal Paper Tray
Paper Tray
550 sheets
Capacity 550 sheets x 2 LTR / A4 : 20 lb (75 g/m2)
x1
Auto Size Setting No (Input from Control Panel)
Low Level Warning Empty only
Bypass
Capacity 50 sheets LTR / A4 : 20 lb (75 g/m2)
Auto Size Setting Yes
Paper Capacity
600 sheets 1,150 sheets
(Std. Configuration)
18 Multi Copy Range 999 sheets
19 Gradation
Text 2 steps
Text / Photo 2 step error diffusion
Photo 256 steps
20 Resolution 600 dpi Scanning and Printing.
Standard Sorting Memory
21 0 MB 8 MB
size
22 Standard Page Memory size 18 MB
Standard: 250 sheets
23 Exit Tray Capacity Install Option
(Upper / Lower bins : 250 sheets)
24 Color No
25 Max Power Consumption Less than 1.4 kW
26 Dimensions
23.5 x 23.6 x
22.7 in 23.5 x 23.6 x 27.6 in
(W x D x H) H: To Platen Glass.
(597 x 600 x (597 x 600 x 701 mm)
576 mm)
27 Projection area Less than 3.85 ft / 0.358 m
28 Occupancy area
Includes Bypass Paper
(W x D) 37.1 X 23.6 in (942 x 600 mm)
Tray.
108.1 lbs 121.3 lbs
29 Weight Main Unit only.
(49 kg) (55 kg)
Options
1 Paper Feed System Max. 550 sheets x 4
550 sheets 2nd/ 4th
Yes Motor is not mounted.
Paper Feed Module
Paper Size Detection Manual (Control Panel)
Low Level Paper Warning Empty only
550 sheets 3rd
Yes Motor is mounted.
Paper Feed Module
Paper Size Detection Manual (Control Panel)
Low Level Paper Warning Empty only
Max. Paper Capacity 2, 250 sheets LTR / A4 : 20 lb (75 g/m2)
7
Description
Items Remarks
DP-2000 DP-2500 DP-3000
2 Cabinet
Stand for
Option
4-Paper Tray Configuration
Stand for
Option
3-Paper Tray Configuration
Stand for
Option
2-Paper Tray Configuration
Stand for
Option for DP-2000 only
1-Paper Tray Configuration
Option for USA and Canada
3 Platen Cover Option
Standard for EU and Other Countries
Free Stop Yes From 30 to 70 degrees.
4 ADF
(Single side type) Yes
Original Set Face Up
Scanning Method Sheet Through
Capacity (Original) 50 sheets (LTR / A4) LTR / A4 : 20 lb (75 g/m2)
SADF Mode No Yes
Free Stop Yes From 30 to 70 degrees.
5 Inverting ADF (i-ADF)
(Duplex Type) Yes
Original Set Face Up
Scanning Method Sheet Through
Capacity (Original) 50 sheets (LTR / A4) LTR / A4 : 20 lb (75 g/m2)
Available for single side
SADF Mode No Yes
scanning only.
Free Stop Yes From 30 to 70 degrees.
6 Exit Tray (Inner) Yes
Tray Position Inner
Number of Bins 1
Face Up / Face Down Face Down
Bin Capacity Upper / Lower bins: 250 sheets
Requires the Optional Dual
Path Exit Guide Unit.Max. 3
Multi Tray Function Option (Inner 2-way)
way using Optional Exit
Tray (Outer) or Finisher.
Shift Tray Function No
8
Description
Items Remarks
DP-2000 DP-2500 DP-3000
Not available with Exit Tray
(Outer).
7 Finisher Yes Requires the Optional
Dual-Path Exit Guide Unit
and Paper Transport Unit.
Tray Position Outer
Number of Bins 1
Face Up / Face Down Face Down
Bin Capacity 1,000 sheets (LTR / A4)
Max. 3 way using Optional
Multi Tray Function Yes
Exit Tray (Inner).
Shift Tray Function Yes
Shift width 0.79 in (20 mm)
No Manual Stapling.
Not available with Rotation.
Staple Function Yes
Not available with INV-R,
A5-R or B5-R.
Stapler Capacity 3,000 pins
LTR / A4: 30 sheets
Number of Staple possible Max. 30 sheets / set LGL: 20 sheets
LDR: 15 sheets
Staple Position Left / Upper (1 position)
Punch Function No
Not available with Finisher.
Requires the Optional Dual-
8 Exit Tray (Outer) Yes
Path Exit Guide Unit and
Paper Transport Unit.
Tray Position Outer
Number of Bins 1
Face Up / Face Down Face Down
Bin Capacity 250 sheets (LTR / A4)
Max. 3 way using Optional
Multi Tray Function Yes
Exit Tray (Inner).
Shift Tray Function No
Shift width -
For Exit Tray (Inner or
9 Dual-Path Exit Guide Unit Yes Outer), Finisher and duplex
printing.
To be used for Exit Tray
10 Paper Transport Unit Yes (Outer), Finisher and duplex
printing.
Requires the Dual-Path Exit
Guide Unit and Paper
11 Automatic Duplex Unit Yes Transport Unit.
Including 16 MB Image
Memory Board.
9
Description
Items Remarks
DP-2000 DP-2500 DP-3000
12 Counter
Yes Only the Harness Kit is
Key Counter Capability
supplied as an option kit.
13 Dehumidifier Option Supplied as service part.
14 Electronic Sorting Board Option (8MB) Standard (8MB) CODEC + 8MB memory
Optional Image Memory 1 Only one of three available
Yes
(8MB) types can be installed.
Optional Image Memory 2
Yes
(16MB)
Optional Image Memory 3
Yes
(128MB)
Features
1 Automatic Features
Auto Magnification Selection Yes
Auto Paper Selection Yes
Auto Density Control Yes
Auto Paper Tray Selection Yes
Reservation while Power
Auto Start Yes
On Initial
Energy Saver Mode
Standby Mode Yes
Energy Saver Mode Yes
Sleep Mode Yes Turns Off the Heater Power.
Power Consumption 1.8 wh 1.9 wh 115 VAC Power Supply
during Sleep Mode 2.9 wh 220 VAC Power Supply
Remote Diagnostic Yes (Fax only) Requires the Fax Option.
Machine Stop while Out of
Yes (PPC function)
Toner
10
Description
Items Remarks
DP-2000 DP-2500 DP-3000
2 Additional Features
Low Level Paper Warning Empty only
Photo Mode Yes 256 steps
No Original Detection
Release Manual key.
Original Detection Release Yes
Available when using the
Original Size key.
Edit / Effects
Book Mode Yes
Edge Mode Yes
Margin Mode Yes
X-Y Zoom No Yes 25 - 400%
Available only when using
Page Numbering No Yes
the ADF.
Inverse Mode (Negative /
No
Positive)
Centering Mode No
Mirror Mode No
Others (Inverting ADF & Requires the Optional
ADU) Inverting ADF and ADU.
LDR → LTR x 2
2-Page Copy Mode Yes
(A3 → A4 x 2, B4 → B5 x 2)
2in1 Yes
1to2 No
4in1 No Yes
1to4 No
Copy from 4 single-sided
Booklet Mode No Yes pages to 1 booklet mode
sheet.
Duplex Copy with Optional ADU
1→2 Option Standard
2→1 Option
2→2 Option
Book→2
Book Format Option Standard
Facing Pages Option Standard
Image Rotation (90 degrees) Yes
Electronic Sorting Yes
Rotation Sorting Yes
Insertion Job
Cover Mode No
Page Insertion Mode No
OHP Interleave Mode Yes Non-copy / Copy
Presentation Mode No
11
Description
Items Remarks
DP-2000 DP-2500 DP-3000
Department Counter Yes (50 departments)
ADF (Optional)
LDR and LTR, LGL and
Multi Size Feed Yes
LTR-R
SADF Mode No Yes
Original Counter No
Job Memory Yes (2) Yes (5)
Job Time Display No
Can Reserve when printing
PC / FAX data.
Concurrent Copy Yes Can NOT Reserve next
copy while printing Copy
data.
User Mode Yes
Interrupt Yes
Electrical Counter Yes
Sky Shot Mode Yes
Check / Slip Mode Yes (2)
Copy Account Display Mode No
3 Control Panel
20 x 2
Display Alphanumeric Large Touch Panel LCD
LCD
GREEN: Scanning /
Status Lamp Yes Printing RED: Alarm /
Warning
Key
Original Size Yes
Copy Size Yes
Keypad Yes
Clear Yes
Stop Yes
Start Yes
Energy Saver Yes
Multi Size Feed Yes
Sort / Finish Yes
User Mode Yes
Original Detection Release No
Interrupt Yes
Reset Yes
Yes
One-Touch key No
(FAX Option)
Fax / PPC / Printer /
Mode Change Yes
Internet Fax Mode change.
12
Description
Items Remarks
DP-2000 DP-2500 DP-3000
LCD Main Indication
Message Language English for USA and Canada
(Default) Specified Language for EU and Other Countries
Message Languages
3
Available
Yes
Original size / Image Yes
(without
Indication (with Image)
Image)
Yes
Paper size / Image Yes
(without
Indication (with Image)
Image)
Paper Tray Selection Yes
Selected Paper Tray / Tray
Yes
Status
No
Original Mode Selection (LED Yes Text / Text-Photo / Photo
Indication)
No
Copy Density Selection (LED Yes 7 Steps
Indication)
Setting Confirmation No Yes
Zoom Magnification Yes
Function Classification No Yes
Number of Copies Yes
SADF: No
SADF / Multi Size Feed Multi Size
Yes
Mode Feed Mode:
Yes
Error Code Yes
No
Finishing (LED Yes
Indication)
Warning Indicators
No
Add Toner (LED Yes
Indication)
Waste Toner Box Full No
No
Add Paper (No Paper) (LED Yes
Indication)
Add Paper
No
(Under 50 sheets)
No
Paper Jam Indication (LED Yes
Indication)
13
Description
Items Remarks
DP-2000 DP-2500 DP-3000
No
Paper Jam Location (LED Yes
Indication)
Service Alert Call Yes
User Error Yes
Machine Error Yes
History of Jam Errors No Yes
Number of Jam Errors
No 30
History
4 Main Unit
Total Counter Yes (Standard) Mechanical Counter
Max. Weight of Documents
11 lb (5 kg)
on the Platen Glass
ADF with Document Guide Yes
Clip Pocket No Yes
Operating Instructions
No
Pocket
Warning / Caution Label Specified Language
5 Optical System
Original Detection Method Reflective Photo Sensor Type
LDR, LGL, LTR, LTR-R, INV, INV-R for USA and Canada
Original Detection Size A3, B4 (FLS), A4, A4-R, A5, A5-R for EU
A3, B4, A4, A4-R, B5, B5-R for Other Countries
Scanning Method 600 dpi CCD
Dehumidifier Option Supplied as a Service Part
Mechanical Multi Copy Mode No
6 Process System
Separate OPC Unit /
Type
Toner Unit Type
Toner
Toner Yield 18,000 pages / cartridge LTR / A4 6% Image
Low Toner Level Sensor Yes
45,000 pages
Drum Life 30,000 pages / drum LTR / A4
/ drum
Developer Life N/A
Waste Toner Box Yes
Dehumidifier Option Supplied as a Service Part
Toner Cartridge
Manual Add Toner Yes
replacement
14
Description
Items Remarks
DP-2000 DP-2500 DP-3000
7 Feeder System
Paper Tray
(Standard / Option)
Paper Size setting method Universal & Fixed by screw
Change Paper Size
Set by Control Panel
method
LDR, LGL, LTR, LTR-R, INV, INV-R for USA and Canada
Setting size A3, B4, A4, A4-R, A5, 8”X13”, 8.5”X13” for EU
A3, B4, A4, A4-R, B5, B5-R for Other Countries
Capacity 550 sheets LTR / A4: 20 lb (75 g/m2)
Low Paper Level Warning Empty only
Bypass
Capacity 50 sheets LTR / A4: 20 lb (75 g/m2)
Paper Size setting method Universal
Change Paper Size
Auto
method
LDR, LGL, LTR, LTR-R, INV, INV-R for USA and Canada
Paper Size Detection A3, B4 (8”X13”, 8.5”X13”), A4, A4-R for EU
A3, B4, A4, A4-R, B5, B5-R for Other Countries
Efficiency
1 Productivity
Warm-Up Time from Stand-
Approx. 35 sec. 68 °F (20 °C)
by
ADF Productivity (LTR / A4)
ADF 100%
Inverting ADF 100%
ADU Copy Productivity
When exiting to Inner Tray
(LTR / A4)
Transport Method Stack less
1→2
1 copy 50% TBD
5 copies 72% TBD
10 copies 80% TBD
2→2
1 copy 45% TBD
5 copies 70% TBD
10 copies 78% TBD
PM Cycle
1 PM Cycle
Major PM 120 k
Minor PM (Cleaning) 60 k
15
Description
Items Remarks
DP-2000 DP-2500 DP-3000
Packing Configuration
29.5 x 27.6 x
32.3 in 29.5 x 27.6 x 37.4 in
1 Packing Dimension
(750 x 702 x (750 x 702 x 950 mm)
820 mm)
132.3 lb
2 Packing Weight 154.3 lb (70 kg)
(60 kg)
3 Accessories
OPC unit Yes
(Toner) Hopper Unit No
Operating Instructions Yes
Power Supply
99 - 138 VAC 47 - 63 Hz
100 VAC Power Supply
Single phase
1 Power Requirement
180 - 264 VAC 47 - 63 Hz
220 VAC Power Supply
Single phase
2 Power Consumption Less than 1500 W
Ambient Conditions
1 Temperature 50 - 80 °F / 10 - 30 °C
2 Relative Humidity 30 - 80%
UL1950 / CSA C22.2 No.950 for USA and Canada
3 Safety
EN60950 for EU and Other Countries
4 Energy Saver Energy Star Compliant
Class A computing device in FCC Rules
5 EMI
Part 15
16
1.2. Fax, Printer and Internet Fax Functions
1.2.1. Fax Function
Description
Items Remarks
DP-2000 DP-2500 DP-3000
Main Specifications
1 Compatibility G3 ITU-T Std & Non-Std (MGCS)
2 PSTN Line Port Yes Max. 2 Channels
3 Leased Line Port No
4 V.24 Line Port No
5 Modem Speed 33.6 - 2.4kbps
6 Coding Scheme JBIG/MMR/MR/MH
7 ECM Yes Conforms to ITU-T
8 Short Protocol Yes (B, D)
ITU-T Image No. 1
9 Transmission Speed Approx. 3 sec.
(A4, Std Resolution)
Transmission
Std 8 x 3.85
Fine 8 x 7.7
S-Fine 8 x 15.4
Communication Resolution 16 x 15.4
10
(pels/mm x lines/mm) Reception
Std 8 x 3.85
Fine 8 x 7.7
S-Fine 8 x 15.4
16 x 15.4
Scanner Mechanism
1 Scanning Device CCD (ADF / Platen)
2 Scanning Speed
Less than 2.0 sec. A4 vertical direction
3 S-Fine :F16 x 15.4
Less than 1.4 sec. A4 horizontal direction
Less than 1.0 sec. A4 vertical direction
4 Fine :F8 x 7.7
Less than 0.7 sec. A4 horizontal direction
Less than 1.0 sec. A4 vertical direction
5 Std :F8 x 3.85
Less than 0.7 sec. A4 horizontal direction
Std 8 x 3.85
Scanning Resolution Fine 8 x 7.7
6
(pel/mm x lines/mm) S-Fine 8 x 15.4
16 x 15.4
7 Document Size (Max.) ADF: Max. A3
8 Effective Scanning Width LDR (11.5") / A3 (292 mm)
9 A3 size TX/RX Yes Conforms to ITU-T A3
10 Reduction XMT Yes A3 to B4 / A3 to A4 / B4 to A4
Face-Up, feed from top page
11 ADF Capacity 50 sheets
LTR / A4 (17 lb / 64 g/m2)
12 Collation Stack Yes (Face Down)
Printer Mechanism
1 Recording Method LP
17
Description
Items Remarks
DP-2000 DP-2500 DP-3000
20 ppm 25 ppm 30 ppm
2 Recording Speed (A4 (A4 (A4
horizontal) horizontal) horizontal)
3 Recording Resolution Fax 406 x 391 dpi
Invoice : Not supported.
Ledger size is transmitted as A3
size for N. American model. If
4 Recording Paper Size Ledger / Legal / Letter / A3 / B4 / A4 / A5
A3 is received, approx. 1" of
image on both edges are not
printed on Ledger size paper.
5 Effective Printing Width 11.4" (289 mm) Conforms to ITU-T A3
Optional max. 2200 sheetsLTR /
6 Recording Paper Capacity 550 sheets 1,100 sheets
A4 : 20 lb (75 g/m2)
7 Collation Stack Yes (Face Down)
8 Consumable Toner Cartridge / OPC Drum
Fax Memory
Flash ROM, ITU-T Image No. 1
1 Standard Memory 2 MB (120 pages)
(A4, Std Resolution)
2 ITU-T #1/standard result
4 MB
3 Optional Memory
8 MB
Dual Operation
1 Multi Task Operation Yes
2 Direct XMT Reserve Yes
3 Memory XMT Reserve Yes
Number of Memory Job
4 Yes (Max. 50 files)
Files
Dialing/Telephone Features
1 Auto Dialers 200
Phone Book Directory
2 Yes
Search Dialing
3 Total Auto Dialers 200
4 Program Dials 5 12
5 Max. Tel Number Digits 36 36
Max. Station Name
6 15
Characters
Full Number Dialing
7 Yes Max.70 stations
(Buffered Dialing)
Direct Dialing
8 Yes Voice mode
(Monitor Dialing)
9 Automatic Redialing Yes
10 Manual Redialing Yes
11 Line Monitor Speaker Yes Available for Line-1 only
12 Chain Dialing (Hybrid Dial) Yes In Monitor Dialing mode only
13 Pulse / Tone Dialing Yes 10 pps / DTMF
14 Pulse to Tone Change Yes
15 Flash Key Yes
16 Handset Option
18
Description
Items Remarks
DP-2000 DP-2500 DP-3000
Transmission Features
1 Direct Transmission Yes
2 Memory Transmission Yes Page Retransmission
Quick Memory
3 Yes
Transmission
Multi-Station Transmission
4 Yes Max. 270 stations
(Sequential Broadcasting)
Direct Deferred
5 No ADF Deferred Transmission
Transmission
6 Deferred Transmission Yes Max. 50 timers
Deferred Multi-Station
7 Yes
Transmission
8 Priority Direct Transmission Yes Priority ADF Transmission
Priority Memory
9 No
Transmission
10 Batch Transmission Yes Real Time (up to 5 Files)
90 Degree Rotation
11 Yes
Transmission
12 Cover Sheet Yes
13 Confidential Mail Box Yes 20 Mailboxes
14 Multi-Copy Transmission No
FAX : Back-up with Flash
Memory.
15 Memory Back-Up Yes
Copy / Printer : No Back-up with
D-RAM
With Optional Inverting ADF (i-
16 Duplex Scanning Yes
ADF)
Reception Features
1 Substitute Reception Yes
LTR/A4/LGL: 70 - 100%
2 Fixed Reduction Yes (in 1% Steps),
Top & Left Alignment
LTR/A4/LGL: 70 - 100%
3 Auto Reduction Yes (in 1% Steps),
Top & Left Alignment
Page End Approx. 0.51 in (13
4 Overlap Printing Yes
mm)
5 Receive to Memory Yes
Distinctive Ring Detector
6 Yes
(DRD)
90 Degree Rotation
7 Yes
Reception
8 Duplex Printing Yes With Optional ADU
Polling
1 Polling Yes
2 Turnaround Polling No
3 Multi-Station Polling Yes Max. 270 stations
4 Deferred Polling Yes Max. 50 timers
19
Description
Items Remarks
DP-2000 DP-2500 DP-3000
Deferred Multi-Station
5 Yes Max. 50 timers / 270 stations
Polling
6 Direct Polling Tx No
7 Memory Polling Tx Yes 1 File
8 Preset Polling Password Yes
Temporary Polling
9 Yes
Password
10 1Continuous Polling No
Convenience
20 x 2
1 Panel Display Alphanumeric 7.5” Touch Panel Display
LCD
2 Voice Contact No
3 Edit File Mode Yes With View Mode
4 Incomplete File Save Yes With View Mode
5 Automatic Cover Sheet Yes
Certainty
1 Verification Stamp Yes
2 Header / Total Page Print Yes
100 Transactions / with View
3 Transaction Journal Yes
Mode
4 Comm. Journal Yes With Image Data
5 Last Ind. XMT Journal Yes
List Printouts
1 One-Touch List Yes No
2 ABBR. No. List Yes No
3 Program List Yes
4 Phone Book Search List Yes Auto Dialer List
5 Fax Parameter List Yes
6 File List Yes With View Mode
7 Ind. XMT Journal Yes
8 Directory Sheet Yes No
Identifications
1 Logo Yes 25 Characters
2 Multiple Logo No
3 Character ID Yes 16 Characters
4 Numeric ID Yes 20 Digits
Special Communications
1 Password XMT / RCV Yes
2 Selective Reception Yes TSI Check
3 Relay XMT Request No
4 Relay XMT Center No
5 Confidential XMT / Polling No
6 Confidential Center No
7 Mailbox XMT / Polling Yes
8 Mailbox Center Yes Max. 20 Mailboxes
9 File XMT No
20
Description
Items Remarks
DP-2000 DP-2500 DP-3000
10 Fax Forward No Received File Transfer
11 Sub-Address XMT Yes T. Routing
12 Sub-address RCV Yes
13 OMR-XMT No
Standards
FCC Part 68: 1997 / Industry Canada
1 PSTN
No. CS-03: Issue 8 1996
Others
For U.S.A/Canada;
Yes
1 Fax Access Code DP-2500 with v2.x Firmware
Yes No for Other Countries
For U.S.A/Canada only;
2 PIN Code Access Yes
DP-2500 with v2.x Firmware
3 Intelligent Redial (A-1) Yes 4 Files
4 Department Code Yes 50 Codes
5 Power Saver Mode Yes
6 Self Diagnostic Function Yes
Remote Diagnostic
7 Yes
Function
8 Check & Call Function Yes
9 V.24 / Encryption Interface No
21
1.2.2. Printer Function
Description
Items Remarks
DP-2000/2500/3000
Interface
Centronics Parallel I/F
1 Centronics Parallel Interface ECP
(IEEE-1284)
Ethernet 10Base-T/
2 LAN (Network) with Optional Internet Fax
100Base-TX
3 USB Port No
4 IEEE-1394 No
Printer Function
Ledger, Legal, Letter, Invoice,
1 Printing Size
A3, A4, A4-R, A5, A5-R, B4
2 Bypass Yes
3 Stapling Yes
4 Printing Resolution 600 dpi
Centronics Parallel Interface/
5 Interface
Ethernet
Win 98 / Win 95 / Win NT 4.0 /
6 OS
Win 2000
7 GDI Yes
8 PDL (PCL6) Yes with Optional PCL6 Emulation kit
9 PDL (PSII) No
10 Duplex Printing Yes with Optional ADU
11 Collation Stack Yes
Win 98 / Win 95 / Win NT 4.0 /
12 Status Monitor Yes
Win 2000 : Local Connection
13 Network Printing Yes with Optional Internet Fax
14 Network Status Monitor No
15 Smoothing No
16 Applicable PC IBM PC, AT or Compatible
17 Multi-Task Operation
Printing while Fax-XMT from
Yes
Memory
Printing while Fax-RCV into
Yes
Memory
Fax-XMT from Memory
Yes
while Printing
Fax-RCV into Memory while
Yes
Printing
Output to separate tray for
18 Yes
Printing, Fax, Copy
19 Font Yes with Optional PCL6 Emulation kit
Password Print with Optional F-ROM
20 Security Print Yes
Card
Scanning Function
256 Halftone shades, Gray LAN : 256 Halftone shades with Error
1 Halftone
Scale (Local Connection) Diffusion Requires Internet Fax Option.
2 Max. Document Size Ledger
22
Description
Items Remarks
DP-2000/2500/3000
Selectable, 600 dpi Optical Scanner,
3 Scanning Resolution 600 dpi (Max)
LAN: 400 dpi (Max.)
4 Driver TWAIN
5 2-Sided Scanning No
23
1.2.3. Internet Fax Function
Description
Items Remarks
DP-2000/2500/3000
Main Specifications
1 Communication Protocols TCP / IP SMTP / MIME
2 Max. Modem Speed NA
3 Coding Scheme MH / MMR 400 dpi : MMR only
4 ECM No
5 Line Interface RJ-45 (Ethernet) Ethernet LAN
Scanner Mechanism
1 Max. Document Size LDR / A3
2 Effective Scanning Width 11.4" (289 mm)
8 x 3.85
Scanning Resolution 8 x 7.7 LAN: 400 dpi Scanning Resolution is
3
(pel/mm x lines/mm) 8 x 15.4 available with Parameter setting.
16 x 15.4
Printer Mechanism
FAX: 406 x 391 dpi,
1 Printing Resolution 600 dpi
Network Printer: 600 dpi
2 Effective Recording Width 11.4" (289 mm)
Transmission Features
Simultaneous operation of G3 Fax and
1 Multi-Task Operation Yes
LAN is available.
2 Memory Transmission Yes
Sequential Multi-Station
3 No
Transmission
Simultaneous Multi-Station
4 Yes Max. 270 stations
Transmission
5 Sender Selection Yes
G3 / Email Mixed
6 Yes
Broadcasting
7 Deferred Transmission Yes
Received File Transfer, only with I-FAX
8 Fax Forward Yes
Option
9 Sub-address RCV Yes Inbound Routing, only with I-FAX Option
10 Mail Header
Email Header Print Selection Yes All or From / To / Subject only
Subject Line Random Entry
LAN Features
A3 Communication is available with
1 Internet Fax Communication Yes
Parameter setting.
2 Internet Mail Reception Yes
24
Description
Items Remarks
DP-2000/2500/3000
3 Internet Fax Server Features
Internet Fax Relay XMT Yes iFAX → iFAX → G3FAX
Email Relay MXT Yes PC → iFAX → G3FAX
Received Fax / Email Forward Yes Local print available
PC to FAX Transmission No
Using Sub-Address. Local print
Inbound Routing Yes
available
Phone Book Registration from
Yes Via Email
PC
I-Fax Parameters Registration
4 Yes
via Email
5 Internet Delivery Confirmation Yes Its own mode
400 dpi (Default / Max.). 600 dpi is not
6 Network Scanning Yes (400 dpi) available. Network Scanning mode can
be selected during setup.
7 Network Printing
LPR / LPD Yes (600 dpi)
Parallel Port is not available when
GDI Yes
connected to the LAN.
PDL Yes Requires Optional PCL6 Emulation Kit.
8 DHCP Client No
Certainty
Email from RCV side to Panafax I-Fax’s
1 Comm. Journal (w / Image) Yes
only.
ID
1 Email Address Yes
25
1.3. System Combination
Each Options
Heater Kit Electronic Sorting Board
(Option for DP-2000)
To
Memory Card 8, 16, 128M
4 or 8M
Either Option
1-Bin Finisher
or
Exit Tray (Outer)
2nd Paper Feed Module Motor, Solenoid, Sensor
(Option for DP-2000/2500)
Option
26
1.4. Options List
27
1.5. External View
Rear view
Top view
45.3 inches (1151 mm)
40.7 inches (1033 mm) 26.3 inches (667 mm)
23.5 inches 23.6 inches
(597 mm) (600 mm)
33.9 inches (862 mm)
27.6 inches (701 mm)
28
1.6. Assembling Figure
29
No. Part Name No. Part Name
1 Actuator 1 (1836) 29 3rd Paper Tray
2 Roller, Pre-Feed (1731) 30 4th Paper Tray
3 Roller, ADF (1728) 31 Roller, Pinch (1518)
4 Roller, Separation (1740) 32 Roller, Feed (1510)
5 Roller, Drive (1872) 33 Roller, Idle (1511)
6 Roller, Pinch (1838) 34 Roller, Drive 2 (1410)
7 Roller, Feed 2 (1753) 35 Roller, Feed (1510)
8 Roller, Exit (1751) 36 Roller, Drive 2 (1410)
9 Stamp Unit 37 Separation (1047)
10 CCD Assembly (207) 38 Roller, Pressure (1027)
11 Glass Assembly (557) 39 Bearing (1039)
12 Glass S (559) 40 Roller, Fuser (1026)
13 Lamp, Xenon (204) 41 Bushing, Insulation (1006)
14 Mirror 1 (264) 42 Bearing (1046)
15 Mirror 2 (265) 43 Gear, E40 Heat Roller (1014)
16 Roller, Drive (1314) 44 Lamp, Fuser (850W) (1043)
17 Roller, Drive (1314) 45 Lamp, Fuser (400W) (1044)
18 Roller, Drive (1314) 46 Drum, OPC (718)
19 Roller, Drive (1314) 47 Roller, Bias Transfer (1221)
20 Thermistor Assembly1, 2 (1041, 1042) 48 Roller, Drive (1409)
21 Thermostat (1038) 49 Roller, Timing pinch (1222)
22 LSU (1124) 50 Cleaner, Roller (1229)
23 Process Assembly (785) 51 Roller, C25 Gear (1145)
24 Toner Cartridge 52 Clutch, Reverse (1132)
25 Roller, Paper Feed (1144) 53 Spring, A (1146)
26 Roller, C25 Gear (1145) 54 Roller, Feed (1244)
27 1st Paper Tray 55 Pad, Separator Holder (1242)
28 2nd Paper Tray 56 Roller, Intermediate (3106)
30
1.7. Control Panel
For DP-2000
For USA/Canada For Other Countries
FLS
A3
B4
A4
A4
A5
31
INTERRUPT
ENERGY SAVER INTERRUPT FUNCTION
FUNCTION RESET
RESET
DP-2500
For DP-2500/3000
CLEAR
CLEAR
ORIGINAL
ORIGINAL COPY
COPY REDIA L/
REDIAL/
MULTI-SIZE SIZE
SIZE SIZE
SIZE PAUSE
PAUSE
SORT FEED
COPY ABC
ABC DEF
DEF
LEDGER
ADD TONER 1 2 3
FLAS H/
FLASH/
SUB-ADDR
SUB-ADDR
FAX GHI
GHI JKL
JKL MNO
MNO
STOP
STOP
LEGAL
For USA/Canada
INTERNET LETTER
PQRS
PQRS TUV
TUV WXYZ
WXYZ
MONITOR
MONITOR 7 8 9
LETTER START
START
PRINTER
ON LINE SET
SET
DATA
0
INVOICE
MON. VOL.
MON. VOL. TONE
TONE
ALARM
ALARM ACTIVE
ACTIVE
32
INTERRUPT
ENERGY SAVER INTERRUPT FUNCTION
FUNCTION RESET
RESET
DP-2500
CLEAR
CLEAR
ORIGINAL
ORIGINAL COPY
COPY REDIA L/
REDIAL/
MULTI-SIZE SIZE
SIZE SIZE
SIZE PAUSE
PAUSE
SORT FEED
COPY ABC
ABC DEF
DEF
A3
ADD TONER 1 2 3
FLAS H/
FLASH/
SUB-ADDR
SUB-ADDR
FAX FLS GHI
GHI JKL
JKL MNO
MNO
STOP
STOP
B4
LCD ON LINE LINE
LINE 4 5 6
CONTRAST
SELECT
SELECT
For Other Countries
INTERNET A4
PQRS
PQRS TUV
TUV WXYZ
WXYZ
MONITOR
MONITOR 7 8 9
A4 START
START
PRINTER
ON LINE SET
SET 0
DATA A5
MON. VOL.
MON. VOL. TONE
TONE
ALARM
ALARM ACTIVE
ACTIVE
1.8. Fan and Motor
Stepping Motor (201)
33
1.9. Sensor
1. Scanner
Platen Cover (ADF)
Angle Sensor SCN PCB
Platen Cover (ADF) (19114)
Home Position
Sensor (270) Open Sensor
2. Printer
Toner Sensor (1123) Paper Exit Sensor (1045)
Registration
Paper Level Sensor (1045)
Sensor (1045) Sheet Bypass Bottom
Plate Sensor (1045)
NP Sensor Sheet Bypass Size
(1045)
Sensor (1045)
Paper Tray
Sensor (1045) Sheet Bypass
NP Sensor (1045)
Counter (1125)
Waste Toner Box
Sensor (1045)
Registration
Sensor (1045)
34
1.10. Clutch and Switch
Feed Roller Clutch (1260)
Registration Roller
Clutch (1260)
Multi Feeder Feed
Roller Clutch (1260)
Intermediate Roller
Clutch (1260)
1.11. PC Board
Touch Panel (123)
SCN PCB (19114)
PNL1 PCB (19120)
PRIF PCB (1991)
CCD (207)
PNL3 PCB (19125)
PNL2 PCB (19121)
LVPS (1999)
35
2 Disassembly Instructions
2.1. General Disassembly Flowchart
2-2-1
Remove the ADF from the machine
ADF Roller Assembly ADF PC Board (19115) ADF Front Cover (1637)
ADF Roller (1728) ADF Cover Detect Sensor (1045) Lower Feed Guide (1873) Assembly
Pre-Feed Roller (1731) Motor Bracket ADF Motor (1801) ADF Door Cover (1831) Assembly
(1811) Assembly
Upper ADF Guide (1723) Sub ADF Cover (1842) Assembly
ADF Front Cover (1637)
Torque Limiter Bushing Read Point Sensor (1045)
(1741) Solenoid Bracket (1761) Assembly
36
2-2-2
Left Platen Cover (514) Right Platen Cover (516) 2-2-3
For DP-2000
EMI Sheet (128)
Lower Rear Cover (506) Control Panel Assembly
PNL4 PC Board (19152) PNL2 PC Board (19121)
Left Rear Cover (517) Right Rear Cover (507) LCD Module (134)
For DP-2500
Rear Platen Cover (504)
Inverter (125)
Front AC SW Cover (534) EMI Sheet (128) (Except for USA and Canada)
Right Front Cover (525) Left Side Cover (535) Right Side Cover (523)
2-2-4
<If Fax Communication Kit is installed>
LCU/ LCE PC Board (1995/ 1994)
<If 2nd G3 Fax Communication Port Kit is installed>
LCU/ LCE PC Board (1995/ 1994)
<If 2nd G3 Fax Communication Port Kit or 10/ 100 Ethernet Interface/ Internet Fax Kit is installed>
G3B/ LANB PC Board (19134/ 1987)
<If 10/ 100 Ethernet Interface/ Internet Fax Kit is installed>
LANC PC Board (1989)
<If Fax Communication Kit is installed>
FXB PC Board (1985) HTC PC Board (1997)
<If 1-Bin Finisher is installed>
Optional Low Voltage PSU (19130) Fan (1126) Low Voltage PSU (1999)
<If Parallel Port Interface Kit is installed> Speaker Assembly (448)
PRIF PC Board PC Board (1991)
CONS PC Board (19158) [For DP-3000 only]
<If Electronic Sorting Board is installed>
SORT PC Board (1984) [For DP-2000 only] <If PCL 6 Emulation Kit is installed>
EP PC Board (19119)
<If 1-Bin Finisher is installed>
IPC PC Board (3006) SC PC Board (1983)
LPC PC Board (1998)
2-2-5
High Voltage PSU (451)
SCN PC Board (19114)
Switch Holder
37
2-2-6
Transmit Motor Xenon Lamp (204) FPC Cable (260) Mirror 2 (265)
(201)
Inverter PC Board (268) Mirror 1 (264) Slider (211)
Glass Assembly (557) Size Sensor 1 / Size Sensor 3 (275/269)
Glass S (559)
CCD Assembly (207)
2-2-7
Fan (1126) Printer Motor Bracket (919) Clutch (950)
Printer Motor (901) Lift DC Motor (1152) Clutch (1260)
Tray Cover (1204) Sheet Bypass Paper Length Sensor (1045)
Open Right Cover (1201) Assembly
Bias Transfer Roller (1221) Registration Roller (1121) Feed Roller (1244)
Registration Pinch Roller Toner Sensor (1123) Separator Holder Pad (1242)
(1222)
Registration Sensor (1045) Bottom Plater Sensor (1045)
Roller Cleaner (1229)
Paper Level Sensor (1045) NP Sensor (1045)
NP Sensor (1045) Process Toner Cartridge
Sensor (1045)
Paper Feed Roller (1144)
Reverse Clutch (1132)
LSU (1124) C25 Gear Roller (1145)
Micro Switch (461) Spring A (1146)
2-2-8 2-2-9
Open Right Cover (1201) Assembly Turn the Power Switch OFF
Fuser Unit Open Front Cover (528)
Fuser Lamps (1043 & 1044) Waste Toner Box
Separation (1047) Toner Cartridge
Separation Sheets (1060) Open Right Cover (1201) Assembly
Thermistor Assembly 1 & 2 Process Assembly
(1041 & 1042)
Waste Toner Chamber (704)
Thermal Fuse (1040) Thermostat (1038)
OPC Drum (718)
Fuser Upper Cover (1002)
Bias Charge Roller (703)
Exit Roller (1028)
Cleaning Blade Assembly (717)
Lower Fuser Cover (1003)
Front Cleaning Felt (722)
Pressure Roller (1027) Bearing (1046)
Rear Cleaning Felt (723)
E40 Heat Roller Gear (1014)
Cleaning Sponge (724)
Insulation Bushing (1006)
Scoop Sheet (725)
Fuser Roller (1026)
Mag Roller Joint (753)
Mag Roller (769)
Gap Roller (746)
Dr Blade (762)
Development Felt (774)
38
2.2. Disassembly Instructions
2.2.1. ADF Roller, Pre-Feed Roller, Torque Limiter Bushing, Torque Limiter Spring,
Separation Roller, ADF PC Board, ADF Motor, Solenoid Bracket,
Reversing Guide 2 Bracket Assembly, Reversing Guide 1 Bracket Assembly,
Stamp Solenoid, Feed 2 Roller
(1) 1 Screw (19).
(2) Remove the CN Cover (510).
(2)
(1)
(3)
(4)
39
(5) 1 Screw (19).
(6) (6) Open the ADF.
(7) 2 Screws (F7).
2 Thumb Screws (1654).
(8) Remove the ADF / iADF.
(7)
(5) (7)
(10)
(13)
(16)
40
(19) Remove the Snap Ring (B9).
(20) Remove the Clutch (1260).
(21) Remove the Bushing (1621).
(22) Remove the Rear ADF Guide (1725).
(22)
(21)
(20)
(19)
(25 )
(29)
(28)
41
(33) Remove the Snap Ring (271).
(35) (36)
(34) (34) Remove the Torque Limiter Bushing (1741)
(33) and Torque Limiter Spring (1742).
Note:
When re-installing the Torque Limiter
Assembly, ensure that the Torque Limiter
Spring is placed into the deeper slot of the
Separation Roller.
(35) Remove the Separation Roller (1740).
(36) Disconnect the APNT Harness (1941) and
remove Sensor (1045) (Original Detection
Sensor).
(37) Disconnect all Connectors on the ADF PC
(37) Board.
(38) (38) 2 Screws (19).
(39) Remove the ADF PC Board (19115).
(37)
(39)
42
(47) 2 Screws (24).
(47) (48) Remove the ADF Motor (1801).
(48)
A.
C.
(51)
(51)
(54)
43
(57) 1 Screw (19).
(58) Remove the Reversing Guide 2 Bracket (1775)
Assembly.
(57)
(58)
(59)
(59)
(59)
(61)
(62)
(67)
44
(69) Disconnect the AMT Harness (1936) from the
(72) (72)
(74) Clutch.
(70) Remove the Snap Ring (B9).
(69)
(71) Remove the Clutch (1260).
(72) Remove 2 Snap Rings (B9).
(73) Remove the Feed 2 Roller (1753).
(74) Open the ADF Exit Cover (1854) Assembly and
remove in the direction of the arrow.
(73) (70)
(71)
(77)
Note 1:
When re-installing the Feed 2 Roller Guide, make
sure that the Feed 2 Roller Guide is inside of the
hook on the Front ADF Bracket.
Note 2:
When re-installing the Clutch, make sure that the
hook of the Clutch is properly placed into the notch
of the Rear ADF Bracket.
45
(78) 1 Screw (19).
(78)
(82)
(84)
46
Note:
When re-installing the EXT Harness (1943), make
sure to route the Harness along the hooks as
illustrated to prevent paper jams.
(8)
(7)
47
(10) 3 Screws (19).
(10) (11) (11) Remove the Sub ADF Cover (1842) Assembly.
(10)
(12)
Note:
When re-installing the Harness, make sure to
route the Harness along the hooks as illustrated.
48
< Cleaning Exit Roller and Inverting Feed Roller>
(3)
(3) Lift the ADF Input Tray (1604).
(4) Open the ADF Exit Cover (1854).
(5) Clean the Exit Roller (1751) and the Inverting
Feed Roller (1853) with a soft cloth, saturated
with isopropyl alcohol.
(4)
49
2.2.2. Left Platen Cover, Right Platen Cover, Control Panel Assembly, Lower Rear Cover,
Left Rear Cover, Right Rear Cover, Rear Platen Cover, Front AC SW Cover, Blind
Cover, Lower Control Panel Cover, Right Front Cover, Front Cover, S Inner Cover,
Exit Cover, Left Side Cover, Right Side Cover
(1) Slide out the Paper Tray.
(1)
(3)
(6)
(10)
(8)
(9)
50
(11) 3 Silver Screws (B1).
(12) 1 Silver Screw (556).
(13) (13) Remove the Left Rear Cover (517) and the
Right Rear Cover (507).
(11)
(13) (12)
(15)
(18)
(16)
(17)
(19)
51
(20) 3 Screws (19).
(20) (20) (21) Remove the Lower Control Panel Cover (526).
(21)
(23)
(22)
(24)
(27)
(25) (26)
(26)
52
(28) Open the Right Cover (1201) Assembly.
(29) Note:
(30) If the Dual-Path Exit Guide Unit (DA-FK200)
is installed, remove it first by reversing the
installation procedure. (See Sect. 9.20.,
(28) P.650)
(29) 3 Silver Screws (B1).
(29)
(30) Remove the Right Side Cover (523).
(32)
(33)
(34)
(35)
53
2.2.3. DP-2000 : EMI Sheet, PNL2 PC Board, PNL4 PC Board, LCD Module
DP-2500/3000 : Inverter, EMI Sheet (Except for USA and Canada), PNL1 PC Board,
PNL2 PC Board, LC Module, Touch Panel, PNL3 PC Board,
Slide Switch Lever
For DP-2000
(1)
(4) (5)
(6)
54
(7) 8 Screws (7B).
(7)x8 (8) Release 2 Latch Hooks.
(8) (9) Remove the PNL4 PC Board (19152).
(8) (9)
(13)
(16)
(20)
55
For DP-2500/3000
(3)
(4)
(6)
(8)
56
< Except for USA and Canada >
(9)
(9) 2 Screws (7B).
(10) (10) Remove the EMI Sheet (128).
(9)
(14)
(15) (16)
(18)
(19)
57
(20) Remove the Insulation Sheet (127).
(21) Remove the Touch Panel (123).
(20)
(21)
(22)
(24)
58
2.2.4. Optional Low Voltage PSU, HTC PC Board, Fan, Speaker, Low Voltage PSU, LCU/
LCE PC Board, LANC PC Board, FXB PC Board, G3B PC Board, LANB PC Board,
SORT PC Board, PRI PC Board, EP PC Board Assembly, LPC PC Board, CONS PC
Board, SC PC Board, Switch Holder, HTC 2 PC Board
(1) Remove all Covers. (Refer to 2.2.2.)
(3) (2) 4 Screws (19).
(3) Remove the LVPS Plate (409).
(2)
(2)
(5)
(4)
(11)
59
(13) 2 Screws (E6).
(13) (14) (13) (14) Remove the Fan (1126).
(15) Disconnect the Fan Connector.
(15)
(18)
(19)
(22)
(20)x3
(19)
(24)
(23)
x7
60
(27) <If FAX Communication Kit is installed>
(25) Disconnect Connector CN25 on the LCU/LCE
PC Board.
(26) (26) 2 Screws (19).
(27) Remove the LCU/LCE PC Board (1995, 1994).
(25)
(30)
(31)
(34)
(35)
61
<If 10/100 Ethernet Interface / Internet Fax Kit is
installed>
(37) 1 Screw (19).
(38) Remove the LANC PC Board (1989).
(39) Disconnect Connector CN200 on the LANC PC
Board.
(38)
(37)
(40)
(41) (42)
(45)
(48) (49)
62
(50) 2 Screws (19).
(51) Remove the Ground Wire of the Finisher
Harness (1975).
(52) Remove the FH Bracket (425).
(52)
(51) (50)
(54)
(53) x4
(59)
(62)
63
(64) 2 Screws (19).
(64) (65) Remove the CONS PC Board (19158).
(65)
(68) (67)
x8
(66)
(71) (70)
(73)
(75) (74)
(53)
64
(76) 2 Screws (19).
(76) (77) Remove the HTC Cover (434).
(77)
(80)
(78)
65
2.2.5. High Voltage PSU, SCN PC Board
(1) Open the Rear Cover Assembly. (Refer to
2.2.4.)
(2) 3 Screws (23).
(3) Remove the Fly Wheel (922).
(2)
(3)
x3
(5)
(4)
(6)
(7) (6)
(10)
66
(11) 1 Screw (19).
(12) Remove the CN Bracket (511) Assembly.
(12)
(11)
(13)
(16) (17)
67
2.2.6. Glass Assembly, Glass S, Xenon Lamp, Size Sensor 3, Size Sensor 1, Inverter PC
Board, FPC Cable, Transmit Motor, CCD Assembly, Slider, Mirror 1, Mirror 2
(1) Remove all Covers. (Refer to 2.2.2.)
(2) (2) 2 Screws (19).
(3) (3) Remove the Glass Assembly (557).
(6)
(7)
68
(8)
(8) 2 Screws (19).
(9) Remove the 2 Lamp Plate Springs (232).
(9) (10) Disconnect Connector CN181 on the LFB PC
(8)
Board.
(9) (11) Remove the Xenon Lamp (204).
(10)
(11)
(14)
(16)
(15)
69
(23) Disconnect Connectors CN1 and CN2 on the
(24) Inverter PC Board.
(24) 1 Screw (19).
(23)
(23) (25) Remove the Inverter Upper Cover (212).
(25)
(29)
70
(34) Remove 2 Sliders on the Connectors.
(35) Remove the FPC Cable (260).
(35) Note:
The Sliders must be re-installed when
reassembling.
(34)
(38)
(37)
(36)
(40)
(43)
(42)
71
(44) Disconnect Connector CN106 on the SC PC
Board.
(45) Release 2 Latch Clips and remove the Ferrite
Core.
(44)
(45)
(47)
Note:
When re-installing the CCD Assembly, align the
Red Mark
hole with the Red Mark on the CCD Assembly with
the hole on the Scanner Base Frame as shown in
the illustration at left and secure it with 3 Red
Screws.
(51)
72
(52) (55) (52) 2 Red Screws (D24).
(52) (53) Remove the Rear Lamp Belt Lock (228).
(54) Remove the Front Lamp Belt Lock (227).
(55) Remove the Lamp Base Bracket (224)
(54) Assembly.
(53)
(56)
(56)
(59)
(62)
(62)
(61)
73
(63) Remove the Slider (211) on the right.
(64) Remove the 2 Sliders (211) on the left.
(63)
(64)
(1)
(5)
74
(6) Install the Lamp Base Bracket (224) Assembly.
Note:
The Bracket must be adjusted by moving it
towards the right edge until it stops against
the notches in the frame. Make sure that the
Mirror 2 Bracket Assembly is positioned in the
notches in the center of the frame.
(6)
(7) (7)
75
2.2.7. Fan, Printer Motor, Lift Motor, Clutch, Bias Transfer Roller, Registration Pinch
Roller, Roller Cleaner, Registration Roller, Toner Sensor, Paper Feed Roller, C25
Gear Roller, Feed Roller, Separator Holder pad, LSU, Micro Switch, Reverse Clutch,
Spring A
(1) Remove all Covers. (Refer to 2.2.2.)
(2) Remove the Fly Wheel (Refer to 2.2.5.)
(3) Remove the Fan Duct B (1108).
(3)
(2)
(5)
(4)
(6)
76
(12) 2 Screws (19).
(13) Remove all Harnesses from the clamps.
(14) Disconnect Connector CN706 on the LPC PC
(13) Board.
(15) Remove the Lift DC Motor (1152) Assembly.
(12)
(15)
(16)x3
(19)
(20)
(21) (19)
(25)
(24)
77
(26) Remove the Discharge Bushing (946).
(29)
(27) (27) Remove the the Snap Ring (B9).
(28) Loose the Hexagon Socket Head Bolt using a
Hexagonal wrench as shown on the left.
(29) Remove the Clutch (950).
(28) (26)
(32)
(34)
(36)
78
(37) Remove the Sheet Bypass Paper Length
Sensor (1045).
(38) Disconnect the Sensor Connector.
(38)
(37)
(40)
(45)
79
(46) Remove the BTR Gear (1234).
(47)
(47) Remove the Bias Transfer Roller (1221).
(46)
Note:
When installing the Roller Cleaner, make sure that
there is no space between the rib and the Roller
Cleaner as shown on the left.
80
(51) Remove the Process Assembly. (Refer to
2.2.9.)
(52) (52) Remove the Snap Ring (B9).
(53) Remove the Registration Roller (1121).
(54)
(56)
(57)
(56)
(59)
81
(62) Push the arm of the Sensor Holder slightly to the
left and remove the Registration Actuator
(1120).
(62)
(63)
(65) (64)
(67)
(69)
(68)
82
(70) Slide out the Paper Tray. When removing the
Paper Tray, the Paper Feed Roller can be
handled from the opening of the Paper Tray
Frame. Remove the Paper Feed Roller (1144)
from the opening.
(70)
Cleaning Paper Feed Roller
Clean the surface of the Paper Feed Roller
with a soft cloth, saturated with isopropyl
alcohol.
(80) (79)
83
(81) 1 Screw (19).
(81) (82) Remove the Feed Roller (1244).
(82)
(83)
(84)
(84) (85)
(86)
84
(88) Release the Hook on the Tray Guide.
(88) (89) (89) Remove the NP Sensor (1045).
(92)
(97)
(98)
85
(100)2 Screws (E5).
(100) (101)Remove the Micro Switch (461).
(101)
86
2.2.8. Fuser Unit, Fuser Lamp, Thermistor Assembly, Thermal Fuse, Thermostat, Exit
Roller, Pressure Roller, Fuser Roller, Insulation Bushing, Separation, Bearing, E40
Heat Roller Gear, Side Fuser Cover, Fuser Paper Guide
CAUTION:
To prevent getting burned, do not install, remove, clean or make adjustments when the Fuser Unit is hot.
(9)
87
(11) Remove the Harnesses from the Clamp and the
Band. The Band on the rear of the machine is
easily removed as shown on the left. Do not cut it
(11) off.
Note:
When re-installing, makes sure to tighten the
Band properly so that harnesses are not
touching the gears of the Fuser Unit.
(11)
(14)
(14)
88
(20) 1 Screw (4N).
(20) (21)
(21) 2 Screws (16).
(22) Remove 2 Lamp Brackets (1018).
(22)
(22)
(23)
89
(24) Remove the 2 Separation Wire Springs (A)
(25)
(A) (1048) and the 2 Separation Springs (B)
(25) (1053).
(25) Remove the 6 Separations (1047).
(B)
Cleaning Thermistors:
Clean the surface of the Thermistors only with
a soft dry cloth.
(31) 2 Screws (23).
(31) (32) Remove the Thermal Fuse (1040).
(32)
90
(33) 1 Screw (4N).
(33) (34) Remove the Thermostat (1038).
(34)
(35)
(39)
91
(44) Remove the Turn Guide (1007) in the direction
of the arrow.
(44)
(48)
(47)
(49)
(50)
92
(51) Remove the 2 Screws (1033), the 2 Pressure
Springs (1029) and the 2 Washers (1052).
(52) Remove the Pressure Roller (1027).
(51) (52)
(54)
(54)
93
(55) Remove the E20 Gear (937), E25 Gear (941),
and E41 Free Gear (1012).
(56) Remove the 2 C-Type Rings (1030).
(56)
(55)
(56)
(57)
Note 1:
(61) The Plate Spacer is installed only to the non-Gear
side.
(59)
Note 2:
Do not scratch the surface of the Fuser Roller
when removing or re-installing it.
94
2.2.9. OPC Drum, Cleaning Blade Assembly, Mag Roller, Dr Blade, Mag Roller Joint, Bias
Charge Roller, Front Cleaning Felt, Rear Cleaning Felt, Cleaning Sponge, Scoop
Sheet, Gap Roller, Development Felt
(1) Turn the Power Switch to the OFF (O) position.
(4) (2) Open the Front Cover (528).
(3) Remove the Waste Toner Box and the Toner
Cartridge. (Refer to Users Guide)
(4) Open the Right Cover (1201) Assembly.
(5) Press down on the Release Latch (1109) and
pull the Process Assembly out slowly until it
(6) stops.
(6) 2 Screws and then remove the Process
Assembly from the machine.
(5)
(6) (6)
(8)
95
(10) Remove the OPC Drum Shaft Holder (707)
(10) Assembly as shown on the right.
(12)
(13)
96
Note:
When re-installing the Bias Charge Roller Holder
Assembly, install the Bias Charge Roller Holder
(A)
(712) first as shown in (A) on the left and then the
Bias Charge Roller Bushing (701) with the
Bushing Coil Spring (702) as shown in (B).
(B)
(14)
(16)
(17)
97
Note 1:
When re-installing, install 2 Cleaning Sponges
(724) first as shown in (A) on the left, then the
Cleaning Blade (717) next as shown in (B), then
the Front Cleaning Felt (722) and Rear Cleaning
Felt (723) as shown in (C) and lastly paste the
(D)
Scoop Sheet (725) as shown in (D).
Note 2:
When re-installing the Cleaning Felts, make sure
that there is no space between the rubber part of
(C) the Cleaning Blade and the Cleaning Felts as
(C)
(B) shown on the left.
Note 3:
(A) When re-installing the Cleaning Sponges and the
Scoop Sheet, paste them flat aligning with the
edge of the OPC Drum Shaft Holder as shown on
(A) the left.
(21) (18)
(20)
98
(23) Remove the Gap Rollers (746).
(23)
(26)
(27)
99
2.3. Screw Identification Template
16 XYN3+8J Screw
18 XYN3+L6 Screw
19 XTB3+8J Screw
1Q XYN3+F10 Screw
1Y XTB3+10J Screw
23 XYN3+F8 Screw
24 XYN4+F8 Screw
2B XTB3+14J Screw
2K XTB26+12J Screw
35 XYN4+F6 Screw
36 XYN3+F6 Screw
100
Ref No. Part No. Figure Remark
4N XSN3+W8PC Screw
5M XYN3+F4 Screw
5Y XUC4 E-Ring
5Z XUC6 E-Ring
6A XTB3+12J Screw
7B XTB26+6J Screw
B4 XTB3+8JK Screw
B5 XSB4+10BN Screw
B9 DZJM000171 E-Ring
101
Ref No. Part No. Figure Remark
C8 XTW3+8SFC Screw
D9 DZPF000001 Nut
E5 XTB3+32J Screw
E6 XTB3+24J Screw
E8 XTW3+10S Screw
F4 DZPA000063 Screw
F5 XSN3+5 Screw
F6 DZPK000021 Washer
102
3 Maintenance, Adjustments and Check Points
3.1. Required Tools
103
No. Part Name No. Part Name
1 Actuator 1 (1836) 29 3rd Paper Tray
2 Roller, Pre-Feed (1731) 30 4th Paper Tray
3 Roller, ADF (1728) 31 Roller, Pinch (1518)
4 Roller, Separation (1740) 32 Roller, Feed (1510)
5 Roller, Drive (1872) 33 Roller, Idle (1511)
6 Roller, Pinch (1838) 34 Roller, Drive 2 (1410)
7 Roller, Feed 2 (1753) 35 Roller, Feed (1510)
8 Roller, Exit (1751) 36 Roller, Drive 2 (1410)
9 Stamp Unit 37 Separation (1047)
10 CCD Assembly (207) 38 Roller, Pressure (1027)
11 Glass Assembly (557) 39 Bearing (1039)
12 Glass S (559) 40 Roller, Fuser (1026)
13 Lamp, Xenon (204) 41 Bushing, Insulation (1006)
14 Mirror 1 (264) 42 Bearing (1046)
15 Mirror 2 (265) 43 Gear, E40 Heat Roller (1014)
16 Roller, Drive (1314) 44 Lamp, Fuser (850W) (1043)
17 Roller, Drive (1314) 45 Lamp, Fuser (400W) (1044)
18 Roller, Drive (1314) 46 Drum, OPC (718)
19 Roller, Drive (1314) 47 Roller, Bias Transfer (1221)
20 Thermistor Assembly1, 2 (1041, 1042) 48 Roller, Drive (1409)
21 Thermostat (1038) 49 Roller, Timing pinch (1222)
22 LSU (1124) 50 Cleaner, Roller (1229)
23 Process Assembly (785) 51 Roller, C25 Gear (1145)
24 Toner Cartridge 52 Clutch, Reverse (1132)
25 Roller, Paper Feed (1144) 53 Spring, A (1146)
26 Roller, C25 Gear (1145) 54 Roller, Feed (1244)
27 1st Paper Tray 55 Pad, Separator Holder (1242)
28 2nd Paper Tray 56 Roller, Intermediate (3106)
104
Important
No. Part Description Comments
Action
1 Memory Data Check 1. Print the RAM DATA for reference and pre-caution.
2. After completing the task(s), print and compare the RAM
DATA with the previously printed one.
2 Auto Document Check & 1. Clean the Rollers with Isopropyl Alcohol when required.
Feeder (ADF) Clean
3 Scanner Unit Check & 1. Clean the Scanning Glass or White Seal Guide with
Clean Isopropyl Alcohol when required.
4 Transmitter Unit Check & 1. Remove any foreign obstacles.
Clean 2. Clean the Rollers with Isopropyl Alcohol when required.
5 Mirrors Check & 1. Do not touch the surface of the Mirrors with your hands.
Clean Clean any dirt or fingerprints with a soft cloth, soaked in
Isopropyl Alcohol.
6 Inspection Items Check 1. Check the Harnesses.
2. Check the Connectors.
3. Check the Screws. If required, replace consumable parts.
7 Gears, Rollers Shafts Check & 1. Check and grease the required Gears and Shafts.
Grease
8 Timing Belts Check & 1. Check for belt looseness or abrasion.
Clean 2. Adjust the Idle Pulley.
105
3.3. Periodic Maintenance Check List
For a detailed Periodic Maintenance Check List, refer to Appendix I at the end of this Service Manual.
106
Ref. Cleaning Replacement/Adjustment Ref.
Mechanical Parts
No. Cycle Method Cycle Procedure Counter
Reverse Clutch 1132 - - 120,000 sheets Refer to F7-03
Paper Feed Roller 1144 60,000 sheets Alcohol 120,000 sheets ch 2.2.7. of the 1st - 4th
C25 Gear Roller 1145 60,000 sheets Alcohol 120,000 sheets Service Manual Paper Tray
A Spring 1146 - - 120,000 sheets Count
Bias Transfer Roller 1221 30,000 sheets Dry soft cloth 120,000 sheets F7-02
(BTR) Total
Roller Cleaner 1229 60,000 sheets Dry soft cloth 120,000 sheets Count
Separator Holder 1242 60,000 sheets Alcohol 120,000 sheets F7-03
Pad Sheet
Feed Roller 1244 60,000 sheets Alcohol 120,000 sheets Bypass
Count
Drive Roller 1314 60,000 sheets Alcohol 240,000 sheets - F7-04 ADF
/ Paper
Transport
Count
Drive Roller 1409 60,000 sheets Alcohol 240,000 sheets - F7-04 ADF
Drive 2 Roller 1410 60,000 sheets Alcohol 240,000 sheets / ADU
Count
Feed Roller 1510 60,000 sheets Alcohol 240,000 sheets - F7-04 ADF
Idle Roller 1511 60,000 sheets Alcohol 240,000 sheets /Dual-Path
Count
ADF Roller 1728 60,000 sheets Alcohol 120,000 sheets Refer to F7-04 ADF
Pre-Feed Roller 1731 60,000 sheets Alcohol 120,000 sheets ch 2.2.1. of the / i-ADF
Separation Roller 1740 60,000 sheets Alcohol 120,000 sheets Service Manual Count
Torque Limiter 1741 60,000 sheets Alcohol 120,000 sheets
Bushing
Torque Limiter 1742 60,000 sheets Alcohol 120,000 sheets
Spring
Note
The Maintenance Cycle is based on the Counter Information for each individual module.To verify the
counter information, print the Total Counter List using the Service Mode:F9 - 03 (Print Device Info.) - 02
(Counter Information)
107
3.4. Updating the Firmware
Unlike other machines with removable EPROM (Erasable Programmable ROM), this machine is equipped
with an F-ROM (Flash ROM). F-ROM offers the flexibility of quick and easy firmware updates, creation of a
master firmware card, backup and restore of firmware and machine parameters.
The following is the basic procedure to update the firmware of the machine. The details are described in the
Firmware Update Kit User’s Guide. (Order No.: DZTP000019)
3.4.1. Creating a Master Firmware Card
A. Utilizing the Firmware Update Kit.
1. Install the Firmware Update Kit.
2. Install a Flash Memory Card (4 MB or higher) into the machine.
3. Follow the instructions included in the Firmware Update Kit User’s Guide.
B. Copying the Firmware from an Existing Machine using a 4MB Flash Memory Card
1. Turn the Power Switch to the OFF (O) position.
2. Install a Flash Memory Card (4 MB or higher) into the machine.
3. Turn the Power Switch to the ON (I) position.
4. Press FUNCTION + ORIGINAL SIZE (LEDGER/A3) keys + Key 3 on the keypad simultaneously.
5. Perform the Copy Service Mode F9-08-00 (Firmware Backup Host Program (4MB)).
6. The firmware is copied into the Flash Memory Card.
7. After the backup is completed, press "RESET" first and then press FUNCTION + CLEAR keys
simultaneously to return to standby.
8. Turn the Power Switch to the OFF (O) position.
9. Remove the Master Firmware Card that you just created from the machine.
10. Turn the Power Switch to the ON (I) position.
11. Use this Master Firmware Card to update the firmware on other machines.
C. Copying the Firmware from an Existing Machine using two 2MB Flash Memory Cards
1. Turn the Power Switch to the OFF (O) position.
2. Install a Flash Memory Card (2 MB) into the machine.
3. Turn the Power Switch to the ON (I) position.
4. Press FUNCTION + ORIGINAL SIZE (LEDGER/A3) keys + Key 3 on the keypad simultaneously.
5. Perform the Copy Service Mode F9-08-01 (Firmware Backup Host Part A (2MB)).
6. The firmware is copied into the Flash Memory Card.
7. After the backup is completed, press "RESET" first and then press FUNCTION + CLEAR keys
simultaneously to return to standby.
8. Turn the Power Switch to the OFF (O) position.
9. Remove the Master Firmware Card that you just created from the machine and install a second
Flash Memory Card (2 MB) into the machine.
10. Turn the Power Switch to the ON (I) position.
11. Press FUNCTION + ORIGINAL SIZE (LEDGER/A3) keys + Key 3 on the keypad simultaneously.
12. Perform the Copy Service Mode F9-08-02 (Firmware Backup Host Part B (2MB)).
13. The firmware is copied into the Flash Memory Card.
14. After the backup is completed, press "RESET" first and then press FUNCTION + CLEAR keys
simultaneously to return to standby.
15. Turn the Power Switch to the OFF (O) position.
16. Remove the Master Firmware Card that you just created from the machine.
17. Turn the Power Switch to the ON (I) position.
18. Use these 2 Master Firmware Cards to update the firmware on other machines.
108
3.4.2. Updating the Firmware (Host) using the Master Firmware Card
A. When a 4 MB Flash Memory Card was used
1. Before starting, print the F5 & F6 Parameters (Copier) and Fax/Function Parameters (Fax) Lists.
2. Turn the Power Switch to the OFF (O) position.
3. Install the appropriate Master Firmware Card into the machine.
4. Turn the Power Switch to the ON (I) position.
5. Press FUNCTION + ORIGINAL SIZE (LEDGER/A3) keys + Key 3 on the keypad simultaneously.
6. Perform the Copy Service Mode F9-07-00 (Firmware Update Host Program (4MB)).
7. The firmware is copied into the machine.
8. After the update is completed, the machine reboots itself and returns to standby.
9. Perform the Copy Service Mode F9-06-00 (Parameter Initialization).
10. Turn the Power Switch to the OFF (O) position.
11. Remove the Master Firmware Card from the machine.
12. Turn the Power Switch to the ON (I) position.
13. Reprogram the F5 & F6 Parameters (Copier) and Fax/Function Parameters (Fax) according to the
lists printed in Step 1 above if the settings are other than factory default.
109
C. Updating the Firmware (Control Panel) using the Master Firmware Card (2 MB or higher)
1. Turn the Power Switch to the OFF (O) position.
2. Remove the Control Panel Assembly (See Sect. 2-2-2 and 2-2-3).
3. Install the Master Firmware (Control Panel) Card into the PNL1 PCB (19120).
4. While holding down the Energy Saver key, turn the Power Switch to the ON (I) position. Keep
holding the Energy Saver key for approximately 10 sec.
5. Upon releasing the key, the firmware is copied into the machine.
6. After the update is completed, the machine reboots itself and returns to standby.
7. Turn the Power Switch to the OFF (O) position.
8. Remove the Master Firmware Card from the PNL1 PCB (19120).
9. Re-install the Control Panel Assembly.
10. Turn the Power Switch to the ON (I) position.
11. Perform the Copy Service Mode F9-02-01 (Control Panel) and verify the Control Panel firmware
version.
110
3.4.3. Erasing the Master Firmware Card
1. Turn the Power Switch to the OFF (O) position.
2. Install the Master Firmware Card into the machine.
3. Turn the Power Switch to the ON (I) position.
4. Press FUNCTION + ORIGINAL SIZE (LEDGER/A3) keys + Key 3 on the keypad
simultaneously.
5. Perform the Service Mode F9-09 (PC → Flash Card).
6. After the Flash Memory Card is erased, machine prompts “PROGRAM CARD?”. Press
“NO”.
7. Press "RESET" first and then press FUNCTION + CLEAR keys simultaneously to return to
standby.
8. Turn the Power Switch to the OFF (O) position.
9. Remove the blank Flash Memory Card from the machine.
10. Insert another Master Firmware Card into the machine (if two 2 MB cards were used).
11. Turn the Power Switch to the ON (I) position.
12. Repeat from Step 4 above if you are erasing another Master Firmware Card.
Revision Code
Model Number (Small Category)
Model Number (Large Category)
111
PRINTER BOARD (PDL) : 3152102 Firmware Version (V3.152102)
LAN BOARD : OPT LA B A V30100 AU
Country Code
ROM Version (V30100)
Reserved
Option Specification
LAN Board (LA LZ)
Option
G3B BOARD : A A V11200 AU
Country Code
AU : USA
AG : Germany
Firmware Version (V1.1200)
Language Code
A : A-English, C-French & Spanish
B : A-English, Spanish & Portuguese
b : English, French & Spanish
g : German, French & Italian
Firmware Type
A : Standard
B : Optional
MODEM : 0605 Firmware Version (V06.05)
3rd PAPER FEED MODULE : 40 0009
112
3.5. Glossary of Electrical Abbreviations
113
Signal Name Description
AAD0 Not Used
AAD1 Not Used
AAD2 Not Used
AC(L) AC Power Supply
AC(N) AC Power Supply
AGND Ground
AIRQ Not Used
AL[0] Address Signal
AL[1] Address Signal
AL[10] Address Signal
AL[11] Address Signal
AL[12] Address Signal
AL[2] Address Signal
AL[3] Address Signal
AL[4] Address Signal
AL[5] Address Signal
AL[6] Address Signal
AL[7] Address Signal
AL[8] Address Signal
AL[9] Address Signal
ARDY Not Used
BAT Battery Voltage
BATVL Battery Voltage
BBA[0] S-DRAM Memory Area Switching Signal
BBA[1] S-DRAM Memory Area Switching Signal
BCS[3] Chip Select Signal
BCS[4] Chip Select Signal
BCS[5] Chip Select Signal
BDCLK[0] S-DRAM Access Clock
BDCLK[1] S-DRAM Access Clock
BID[0] Image -BUS
BID[1] Image -BUS
BID[10] Image -BUS
BID[11] Image -BUS
BID[12] Image -BUS
BID[13] Image -BUS
BID[14] Image -BUS
BID[15] Image -BUS
BID[2] Image -BUS
BID[3] Image -BUS
BID[4] Image -BUS
BID[5] Image -BUS
BID[6] Image -BUS
BID[7] Image -BUS
BID[8] Image -BUS
BID[9] Image -BUS
BMA[0] Address Signal
114
Signal Name Description
BMA[1] Address Signal
BMA[10] Address Signal
BMA[11] Address Signal
BMA[12] Address Signal
BMA[2] Address Signal
BMA[3] Address Signal
BMA[4] Address Signal
BMA[5] Address Signal
BMA[6] Address Signal
BMA[7] Address Signal
BMA[8] Address Signal
BMA[9] Address Signal
BMD[0] Data Signal
BMD[1] Data Signal
BMD[10] Data Signal
BMD[11] Data Signal
BMD[12] Data Signal
BMD[13] Data Signal
BMD[14] Data Signal
BMD[15] Data Signal
BMD[16] Data Signal
BMD[17] Data Signal
BMD[18] Data Signal
BMD[19] Data Signal
BMD[2] Data Signal
BMD[20] Data Signal
BMD[21] Data Signal
BMD[22] Data Signal
BMD[23] Data Signal
BMD[24] Data Signal
BMD[25] Data Signal
BMD[26] Data Signal
BMD[27] Data Signal
BMD[28] Data Signal
BMD[29] Data Signal
BMD[3] Data Signal
BMD[30] Data Signal
BMD[31] Data Signal
BMD[4] Data Signal
BMD[5] Data Signal
BMD[6] Data Signal
BMD[7] Data Signal
BMD[8] Data Signal
BMD[9] Data Signal
BRICLK Electronic Sorting Board Clock Signal
BUZCLK Buzzer Clock
BZCLK Buzzer Signal
115
Signal Name Description
CE1 +5 VDC Power Supply
CHARGE Charge Signal (High Voltage)
CK14M Modem Clock
CP Data Shift Clock Signal
CR0 Charge Control DC Output
CR1 Charge Control DC Output
CS Chip Select Signal
D[0] Data Signal
D[1] Data Signal
D[2] Data Signal
D[3] Data Signal
D[4] Data Signal
D[5] Data Signal
D[6] Data Signal
D[7] Data Signal
D0 Data Signal
D1 Data Signal
D2 Data Signal
D3 Data Signal
DAA1 ADF Motor Current Control Signal
DB[0] Data Signal
DB[1] Data Signal
DB[2] Data Signal
DB[3] Data Signal
DB[4] Data Signal
DB[5] Data Signal
DB[6] Data Signal
DB[7] Data Signal
DEVELOPMENT Development Signal (High Voltage)
DR0 Development Control AC+DC Output
E Data Read/Write Enable Signal
FCK1 Shift Register Clock
FCK2 Shift Register Clock
FCP Clamp Clock
FER Transfer Signal (High Voltage)
FGND Ground
FLNG Inverter Control Signal
FR Reset Gate Clock
FRM Frame Signal
FSH Transfer Gate Clock
GND Ground
HITON Dehumidifier Heater Control Signal
HLIN1 Line Signal for the Fax Handset
HLIN2 Line Signal for the Fax Handset
HVAC1 INV PC Board/Lamp Signal
HVAC2 INV PC Board/Lamp Signal
HYBSR Line Transformer Input Signal
116
Signal Name Description
HYSIG Not Used
ID0 Flash Card ID
ID1 Flash Card ID
ID2 Flash Card ID
IOD[0] Data Signal
IOD[1] Data Signal
IOD[10] Data Signal
IOD[11] Data Signal
IOD[12] Data Signal
IOD[13] Data Signal
IOD[14] Data Signal
IOD[15] Data Signal
IOD[2] Data Signal
IOD[3] Data Signal
IOD[4] Data Signal
IOD[5] Data Signal
IOD[6] Data Signal
IOD[7] Data Signal
IOD[8] Data Signal
IOD[9] Data Signal
IOD10 Data Signal
IOD11 Data Signal
IOD12 Data Signal
IOD13 Data Signal
IOD14 Data Signal
IOD15 Data Signal
IOD8 Data Signal
IOD9 Data Signal
IORD I/O Read Signal
IOWR I/O Write Signal
IOWRH I/O Write (High) Signal
IOWRL I/O Write (Low) Signal
KEYIN0 Key Scan Signal
KEYIN1 Key Scan Signal
KEYIN2 Key Scan Signal
KEYIN3 Key Scan Signal
KEYIN4 Key Scan Signal
KEYIN5 Key Scan Signal
KEYIN6 Key Scan Signal
KEYIN7 Key Scan Signal
KIN[1] Key Scan Signal
KIN[2] Key Scan Signal
KIN[6] Key Scan Signal
L+5V Laser Circuit +5 VDC Power Supply
L1(B) Line Signal
L2(A) Line Signal
LASERPOW Laser Power Control
117
Signal Name Description
LD2WAY Photo Sensor DC Drive Voltage
LDCRT Photo Sensor DC Drive Voltage
LDCST Photo Sensor DC Drive Voltage
LDCST3 Photo Sensor DC Drive Voltage
LDDUP1 Photo Sensor DC Drive Voltage
LDDUP2 Photo Sensor DC Drive Voltage
LDDUP3 Photo Sensor DC Drive Voltage
LDDUP4 Photo Sensor DC Drive Voltage
LDESEN Photo Sensor DC Drive Voltage
LDEX1 Photo Sensor DC Drive Voltage
LDEX2 Photo Sensor DC Drive Voltage
LDEX3 Photo Sensor DC Drive Voltage
LDEX4 Photo Sensor DC Drive Voltage
LDFPCHK Photo Sensor DC Drive Voltage
LDFPCHK2 Photo Sensor DC Drive Voltage
LDFPCHK3 Photo Sensor DC Drive Voltage
LDJAM Photo Sensor DC Drive Voltage
LDJAM3 Photo Sensor DC Drive Voltage
LDMF4 Photo Sensor DC Drive Voltage
LDMFP Photo Sensor DC Drive Voltage
LDMFR Photo Sensor DC Drive Voltage
LDPDOR2 Photo Sensor DC Drive Voltage
LDPHK3 Photo Sensor DC Drive Voltage
LDPS Photo Sensor DC Drive Voltage
LDROR Photo Sensor DC Drive Voltage
LDRSEN Photo Sensor DC Drive Voltage
LDSP2 Photo Sensor DC Drive Voltage
LDUPL Photo Sensor DC Drive Voltage
LDUPL3 Photo Sensor DC Drive Voltage
LED0 LED Matrix Signal
LED1 LED Matrix Signal
LED2 LED Matrix Signal
LED3 LED Matrix Signal
LED4 LED Matrix Signal
LED5 LED Matrix Signal
LED6 LED Matrix Signal
LED7 LED Matrix Signal
LEDA Select Sensor Signal
LEDB Select Sensor Signal
LEDC Select Sensor Signal
LEDCT0 LED Matrix Signal
LEDCT1 LED Matrix Signal
LEDX Select Sensor Signal
LEDY Select Sensor Signal
LEDZ Select Sensor Signal
LH[3] LED Matrix Signal
LINK LANB PCB/ LANC PCB Link Signal
118
Signal Name Description
LOAD Data Latch Signal
LV[0] LED Matrix Signal
LV[1] LED Matrix Signal
LV[2] LED Matrix Signal
LV[3] LED Matrix Signal
LV[5] LED Matrix Signal
LV[6] LED Matrix Signal
LV[7] LED Matrix Signal
LV[8] LED Matrix Signal
MGND Ground
MIC (-) Handset Microphone
MIC (+) Handset Microphone
n2WAYKEP1 Paper Stopper Solenoid Signal
n2WAYKEP2 Paper Stopper Solenoid Signal
n2WAYSEN Inner Upper Tray Paper Exit Signal
n5VCBSY Command Busy Signal
n5VCMD Command Signal
n5VCS2 Chip Select Signal
n5VFED Feed Signal
n5VLPCLK Clock Signal
n5VPDLRD Read Signal
n5VPRNT Printer On Signal
n5VRD CPU Read Signal
n5VREQ Video Request Signal
n8P16M Sort Memory Capacity Signal
nA[0] Address Signal
nA3SEN Sheet Bypass Paper Size Detection Signal
nA3SN Original Width Detection Signal
nAA3S Original Width Detection Signal
nAADL1 Original Length Detection Signal
nAADL2 Original Length Detection Signal
nAAPNT Original Detection Signal
nAB1SN Read Point Detection Signal
nAB2SN Duplex Eject Detection Signal
nAB4S Original Width Detection Signal
nACK[1] Modem ACK[1] Signal
nACLH3 Inverting Roller Clutch Control Signal
nACLOCKAD1 ADF Motor Control Clock Signal
nACSW Relay Control Signal
nADF1 Feed Roller Drive Signal
nADF2 2nd Paper Tray Feed Roller Drive Signal
nADF3 3rd Paper Tray Feed Roller Drive Signal
nADL1 Original Length Detection Signal
nADL2 Original Length Detection Signal
nAEJC Original Eject Detection Signal
nAKEEP1 Reversing 1 Guide Solenoid Control Signal
nAKEEP2 Reversing 1 Guide Solenoid Control Signal
119
Signal Name Description
nAOAC ADF Cover Open Detection Signal
nAPACHG Duplex 2 Guide Solenoid Control Signal
nAPICR Release Lever Plate Solenoid Control Signal
nAREV ADF Exit Cover Open Detection Signal
nASTAMP Stamp Control Signal
nASTROAD1 ADF Motor Control Strobe Signal
nATARST Not Used
nB4SENS Sheet Bypass Paper Detection Signal
nBCAS S-DRAM Column Address Strobe Command
nBCKE S-DRAM Clock Enable
nBCS[2] Chip Select Signal
nBCS[3] Chip Select Signal
nBCS[4] Not Used
nBCS[5] Not Used
nBDQMH Input/Output Mask Signal
nBDQML Input/Output Mask Signal
nBMWT S-DRAM Write Enable
nBRAS S-DRAM Row Address Strobe Command
nCARTRIGE Waste Toner Box Detection Signal
nCASETT Paper Tray Detection Signal (1st Feeder)
nCCLH1 Feed 2 Roller Clutch Control Signal
nCCLH2 ADF Roller Clutch Control Signal
nCD Flash Card ID
nCNTDET Key Counter Option Detection
nCOUNT Counter Drive Signal
nCS00 Modem Control Signal
nCS02 Chip Select Signal
nCS03 Chip Select Signal
nCS05 Chip Select Signal
nCS08 Chip Enable Signal
nCS09 Chip Enable Signal
nCS0A Chip Enable Signal
nCS0D Chip Enable Signal
nCS0E Chip Enable Signal
nCS11 Chip Select Signal
nCS3 Chip Select Signal
nCST 4th Paper Tray Detection Signal
nCST2 2nd Paper Tray Detection Signal
nCST3 3rd Paper Tray Detection Signal
nCSTOP 2nd Paper Feed Module Detection Signal
nCTON Ring Detection Signal
nCTON2 Ring Detection Signal
nDADFON ADF Option Detection Signal
nDOOR Paper Transport Unit Open Detection Signal
nDRAKR Direct Memory Accept Signal
nDRAKS DMA Accept Signal
nDSPOFF Display Off Signal
120
Signal Name Description
nDUPSEN1 Duplex Sensor1 Signal
nDUPSEN2 Duplex Unit Paper Detection Signal
nDUPSEN3 Duplex Unit Paper Detection Signal
nDUPSEN4 Duplex Unit Paper Detection Signal
nEBZON Buzzer Enable Signal
nESEN Inner Under Tray Paper Exit Signal
nEXDF1 Paper Transport Unit Paper Detection Signal
nEXDF2 Paper Transport Unit Paper Detection Signal
nEXDF3 Paper Transport Unit Paper Detection Signal
nEXDF4 Paper Transport Unit Paper Detection Signal
nFAXDET Fax Option Detection Signal
nFDBSY Feed Busy Signal
nFDPCHK 4th Paper Tray Paper Registration Detection Signal
nFDPCHK2 2nd Paper Tray Paper Registration Detection Signal
nFDPCHK3 3rd Paper Tray Paper Registration Detection Signal
nFDPCHK4 4th Paper Tray Paper Registration Detection Signal
nFLON Inverter Ground
nFNRDT Fan Ready Signal
nFXBOPT Fax Option Detection Signal
nHDF Multi Feeder Feed Roller Drive Signal
nHKOF External Phone Off-Hook Detection Signal
nHKOF2 Hook Detection Signal
nHSDT Handset Off-Hook Detection Signal
nHSYNC Horizontal Synchronous Signal
nIODACK[6] Direct Memory Access Data Receive Signal
nIODACK[7] Direct Memory Access Data Receive Signal
nIORD I/O Read Signal
nIORST3V Reset Signal
nIOWR I/O Write Signal
nIOWRH I/O Write (High) Signal
nIOWRL I/O Write (Low) Signal
nIRQBS0 Printer Interrupt Signal
nIRQBS1 Printer Interrupt Signal
nIRQMD0 Modem Interrupt Request Signal
nIRQOP1 Interrupt Signal
nIRQOP2 Interrupt Signal
nJAMDOR 2nd Paper Tray Jam Access Cover Open Detection Signal
nJAMDOR2 2nd Paper Tray Jam Access Cover Open Detection Signal
nJAMDOR3 3rd Paper Tray Jam Access Cover Open Detection Signal
nKCNT Key Counter Option
nKEEP1 Paper Stopper Solenoid Signal
nKEEP2 Paper Stopper Solenoid Signal
nLDON Laser Control
nLIFTM2 2nd Paper Tray Lift Motor Drive Signal
nLIFTM3 3rd Paper Tray Lift Motor Drive Signal
nLPOW Energy Saver Mode Control Signal
nMB4 Memory Version Detection Signal
121
Signal Name Description
nMDRST Modem Reset Signal
nMFPCK Sheet Bypass Paper Detection Signal
nMFRCHK Sheet Bypass Pressure Plate Detection Signal
nMFSEN4 Sheet Bypass Paper Length Detection Signal
nMIRQBG Interrupt Request Signal
nMIRQMD1 Modem Interrupt Request Signal
nMIRQPDL Interrupt Request Signal
nMIRQPM Interrupt Request Signal
nMMCK Printer Motor Clock
nMMON Printer Motor Rotation Control Signal
nMMP0a Motor Drive Signal
nMMP2a Motor Drive Signal
nMMRDY Lift DC Motor Ready Signal
nMRCLH2 2nd Paper Tray Intermediate Roller Clutch Drive Signal
nMRCLH3 3rd Paper Tray Intermediate Roller Clutch Drive Signal
nOE Read Enable
nOP2WAY Dual-Path Exit Guide Unit Detection Signal
nOP3RST Paper Tray Interface Reset Signal
nOPB1 Option Detection Signal
nOPB2 Option Detection Signal
nOPB3 Option Detection Signal
nOPCBSY Paper Tray Command Busy Signal
nOPCLK Paper Tray Command Status Clock Signal
nOPCMD Paper Tray Command Signal
nOPDUP Duplex Unit Option Detection
nOPFEDBSY Paper Tray Feed Clutch Busy Signal
nOPFEED Paper Tray Feed Clutch Signal
nOPON Option Detection Signal
nOPSBSY Paper Tray Status Busy Signal
nOPSTA Paper Tray Status Signal
nOPTRP Transport Unit Installed Detection Signal
nORI Home Position Detection Signal
nOUTA Motor Control Signal
nOUTB Motor Control Signal
nPCHK 4th Paper Tray Paper Detection Signal
nPCHK1 1st Paper Tray Paper Detection Signal
nPCHK2 2nd Paper Tray Paper Detection Signal
nPCHK3 3rd Paper Tray Paper Detection Signal
nPDLOPT Option Detection Signal
nPDLRST Reset Signal
nPDOR2 2nd Paper Tray Paper Level Signal
nPHY1 Shift Register Clock
nPHY2 Shift Register Clock
nPHYCP Clamp Clock
nPHYR Reset Gate Clock
nPMON Polygon Motor Rotation Signal
nPMRDY Polygon Motor Ready Signal
122
Signal Name Description
nPNLRST Panel Reset Signal
nPRDY Printer Ready Signal
nPSAVE Energy Saver Mode Transport Signal
nPSDES Energy Saver Mode Disable Signal
nRD Read Pulse
nRRCLH Registration Roller Drive Signal
nRSEN Registration Sensor Signal
nRST IPC PC Board Reset Signal
nRST3V Reset Signal
nRST5V Reset Signal
nS/H Sample Hold Signal
nSBACK Direct Memory Access BUS Receive Signal
nSBSY Status Busy Signal
nSCBSY Command Busy Signal
nSCRST Reset Signal
nSDACK Direct Memory Access Data Receive Signal
nSENT PRIF PCB Detection Signal
nSLPKY Sleep Key Signal
nSLPKY1 Sleep Key Signal
nSORDET Sort Option Detection Signal
nSOROPT Print Speed Signal
nSPON Speaker SW
nSSBSY Status Busy Signal
nSSR Heater Control Signal
nSTA Status Signal
nSWAKUP Energy Saver Reset Signal
nTRPJAM Transport Unit Open Detection Signal
nTRPSEN1 Transport Unit Sensor Signal
nTRPSEN2 Transport Unit Sensor Signal
nTRPSEN3 Transport Unit Sensor Signal
nTRPSEN4 Transport Unit Sensor Signal
nUPLIMIT 4th Paper Tray Paper Level Signal
nUPLIMIT1 Paper Level Signal (1st Feeder)
nUPLIMIT2 2nd Paper Tray Paper Level Signal
nUPLMT3 3rd Paper Tray Paper Level Signal
nVOL0 Monitor Volume
nVOL1 Monitor Volume
nVOL2 Monitor Volume
nVOL3 Monitor Volume
nVSYNC Vertical Synchronous Signal
nWAIT BUS Wait Signal
nWAIT[1] BUS Wait Signal
nWAIT[2] BUS Wait Signal
nWAIT[3] BUS Wait Signal
nWAIT[4] BUS Wait Signal
nWAIT[5] BUS Wait Signal
nWAKUP Energy Saver Mode Enable
123
Signal Name Description
nWAKUPPC Energy Saver Mode Reset Signal
nWEL Write Low Enable
nWR Light Pulse
nWRH High Enable
OPPRST Ground
ORISENCMN Sensor +2.8 VDC Power Supply
OUTA Motor Control Signal
OUTB Motor Control Signal
p5VBKCNT0 Memory Area Switching Signal
p5VBKCNT1 Memory Area Switching Signal
pABCON Reserved Signal
pACLH1 Feed 2 Roller Clutch Control Signal
pACLH2 ADF Roller Clutch Control Signal
pACLH3 Inverting Roller Clutch Control Signal
pADATA1A ADF Motor Control Signal
pADATA1B ADF Motor Control Signal
pADF 4th Paper Tray Registration Signal
pAPACHG Duplex 2 Guide Solenoid Control Signal
pAPICR Release Lever Plate Solenoid Control Signal
pASTAMP ADF Stamp Solenoid Control Signal
pBREQ Direct Memory Access Data Request Signal
pCMLD Line Switching Relay Drive Signal
pCMLDA Line Switching Relay Drive Signal
PD[0] Data Signal
PD[1] Data Signal
PD[10] Data Signal
PD[11] Data Signal
PD[12] Data Signal
PD[13] Data Signal
PD[14] Data Signal
PD[15] Data Signal
PD[2] Data Signal
PD[3] Data Signal
PD[4] Data Signal
PD[5] Data Signal
PD[6] Data Signal
PD[7] Data Signal
PD[8] Data Signal
PD[9] Data Signal
pDREQRIS Direct Memory Accept Data Request Signal
pDREQSEN PRIF DMA Switching Signal
pEAKD Not Used
pFDCHK3 3rd Paper Tray Registration Signal
PHYTG Transfer Gate Clock
pIODREQ[6] Direct Memory Access Data Request Signal
pIODREQ[7] Direct Memory Access Data Request Signal
pIOOACK[4] Direct Memory Access Data Receive Signal
124
Signal Name Description
pIOOACK[5] Direct Memory Access Data Receive Signal
pIOOREQ[4] Direct Memory Access Data Request Signal
pIOOREQ[5] Direct Memory Access Data Request Signal
pKEEP1 ADF Document Stopper Solenoid Control Signal
pKEEP2 ADF Document Stopper Solenoid Control Signal
pLCDON Inverter Control Signal
pLDCTL Laser Control
pLEDON0 LED Lighting Signal
pLEDON1 LED Lighting Signal
pLEDSLP LED Lighting Signal
pLIFT 4th Paper Tray Lift Motor Signal
pLIFT2 2nd Paper Tray Lift Motor Signal
pLPRST LP Reset Signal
PMCK Polygon Motor Clock
pMIRQCD0 Interrupt Request Signal
pMIXDT Line Switching Relay Drive Signal
pMMP0a Motor Drive Signal
pMMP2a Motor Drive Signal
pMONSW Monitor SW
pMRCLH 4th Paper Tray Intermediate Roller Clutch Signal
pMRCLH2 2nd Paper Tray Intermediate Roller Clutch Signal
pNAISEN Line Switching Relay Drive Signal
PNLCK Communication Clock Signal
pOP1RST Reset Signal
pOP2RST Reset Signal
pOP3RST Reset Signal
pPADF2 2nd Paper Tray Registration Signal
pPDLREQ Direct Memory Access Data Request Signal
pPHY1 Shift Register Clock
pPHY2 Shift Register Clock
pPHYCP Clamp Clock
pPHYR Reset Gate Clock
pPLSD Pulse Dial Relay Drive Signal
pPRIRST Printer Reset Signal
PRXD Reception Signal
pTCKD Not Used
pTRPKEP1 Transport Unit Solenoid Signal
pTRPKEP2 Transport Unit Solenoid Signal
pTRPMDA Transport Unit Motor Signal
pTRPMDB Transport Unit Motor Signal
pTRPMNA Transport Unit Motor Signal
pTRPMNB Transport Unit Motor Signal
PTXD Transmission Signal
pVREF1 Transport Unit Motor Current Setup Signal
pVREF2 Transport Unit Motor Current Setup Signal
pZCIN Heater Control Signal
R/W Data Read/Write Select Signal
125
Signal Name Description
RCV (-) Handset Receiver
RCV (+) Handset Receiver
RS Resister Select Signal
RX- Reception Data "-" Signal
RX+ Reception Data "+" Signal
RXD Reception Data Signal
SCN[0] Key Scan Signal
SCN[1] Key Scan Signal
SCN1 Key Scan Signal
SCN2 Key Scan Signal
SCN3 Key Scan Signal
SCN4 Key Scan Signal
SCN5 Key Scan Signal
SCPURXD5V Reception Data Signal
SCPUTXD5V Transmission Data Signal
SMEMID[0] Memory ID
SMEMID[1] Memory ID
SMEMID[2] Memory ID
SMEMID[3] Memory ID
SPKOUT Monitor Signal
T1 Line Signal for the External Telephone
T2 Line Signal for the External Telephone
TGND Ground
THERM Thermistor Output Signal
THERM2 Thermistor Output Signal
TONERSEN Toner Sensor Signal
TR0 Transfer Control Cleaning Output
TR1 Transfer Control Transfer Output
TRCP +2.5 VDC Power Supply
TURS Not Used
TX- Transmission Data "-" Signal
TX+ Transmission Data "+" Signal
TXD Transmission Data Signal
V0 +0.16 VDC Power Supply
VCC +5 VDC Power Supply
VDD +5 VDC Power Supply
-VDO Video Signal (LVPS - Output)
VEE +24 VDC Power Supply
VINA Sensor Input Signal
VINX Sensor Input Signal
VLCD LCD Drive Volume Voltage
VOUT1 Graphic Data Output
VOUT2 Graphic Data Output
VOUTA Sensor Control Signal
VOUTX Sensor Control Signal
VSS Ground
X1 Touch Panel Matrix Signal
126
Signal Name Description
X2 Touch Panel Matrix Signal
Y1 Touch Panel Matrix Signal
Y2 Touch Panel Matrix Signal
127
3.6. SC PC Board
CN100
Pin No. Signal Name Destination Signal Waveform Function
CN100-1 nSTA LPC PCB +5V(H) Status Signal
CN720-1
0V(L)
CN100-2 n5VLPCLK LPC PCB +5V(H) Clock Signal
CN720-2
0V(L)
CN100-3 nVSYNC LPC PCB Vertical Synchronous Signal
CN720-3 +5V(H)
0V(L)
0V(L)
CN100-6 n5VCBSY LPC PCB +5V Command Busy Signal
CN720-6 H: Command Not Busy
L: Command Busy
0V(L)
0V(L) (Active)
0V(L)
CN100-10 GND LPC PCB Ground
CN720-10
0V
0V(L)
128
Pin No. Signal Name Destination Signal Waveform Function
CN100-12 GND LPC PCB Ground
CN720-12
0V
0V(L)
CN101
Pin No. Signal Name Destination Signal Waveform Function
CN101-1 +24V LVPS PCB +24V +24 VDC Power Supply
CN61-1
129
Pin No. Signal Name Destination Signal Waveform Function
CN101-8 MGND LVPS PCB Ground
CN61-8
0V
-12V
CN102
Pin No. Signal Name Destination Signal Waveform Function
CN102-1 +24V Key Counter +24V +24 VDC Power Supply
Option
0V (Count)
130
Pin No. Signal Name Destination Signal Waveform Function
CN102-3 GND Key Counter Ground
Option
0V
CN102-5 N.C.
CN102-6 N.C.
CN103
Pin No. Signal Name Destination Signal Waveform Function
CN103-1 GND SCN PCB Ground
CN2-1
0V
131
Pin No. Signal Name Destination Signal Waveform Function
CN103-9 +5V SCN PCB +5V +5 VDC Power Supply
CN2-9
0V(L)
CN103-14 SCPURXD5V SCN PCB +5V(H) Reception Data Signal
CN2-14
0V(L)
CN103-15 N.C. SCN PCB Not Used
CN2-15
0V(L)
0V(L)
CN103-18 nSCRST SCN PCB Reset Signal
CN2-18 +5V(H)
0V(L)
0V(L)
CN103-20 nSWAKUP SCN PCB Energy Saver Reset Signal
CN2-20 +5V(H) H: Not Reset
L: Reset
0V(L)
132
CN104
Pin No. Signal Name Destination Signal Waveform Function
CN104-1 GND FLASH CARD Ground
CN1-1
0V
0V(L)
CN104-3 IOD[4] FLASH CARD +5V Data Signal
CN1-3
0V(L)
CN104-5 IOD[6] FLASH CARD +5V(H) Data Signal
CN1-5
0V(L)
CN104-6 IOD[7] FLASH CARD +5V(H) Data Signal
CN1-6
0V(L)
CN104-7 CE1 FLASH CARD +5V +5 VDC Power Supply
CN1-7
0V(L)
CN104-9 nOE FLASH CARD Read Enable
+3.3V(H)
CN1-9 H: Read Disable
L: Read Enable
0V(L)
CN104-10 A[12] FLASH CARD Address Signal
+3.3V(H)
CN1-10
0V(L)
CN104-11 A[10] FLASH CARD Address Signal
+3.3V(H)
CN1-11
0V(L)
133
Pin No. Signal Name Destination Signal Waveform Function
CN104-12 A[9] FLASH CARD Address Signal
+3.3V(H)
CN1-12
0V(L)
CN104-13 A[14] FLASH CARD Address Signal
+3.3V(H)
CN1-13
0V(L)
CN104-14 A[15] FLASH CARD Address Signal
+3.3V(H)
CN1-14
0V(L)
CN104-15 nWEL FLASH CARD Write Low Enable
+3.3V(H)
CN1-15 H: Write Disable
L: Write Enable
0V(L)
CN104-16 N.C. FLASH CARD Not Used
CN1-16
0V(L)
CN104-20 A[16] FLASH CARD Address Signal
+3.3V(H)
CN1-20
0V(L)
CN104-21 A[13] FLASH CARD Address Signal
+3.3V(H)
CN1-21
0V(L)
CN104-22 A[8] FLASH CARD Address Signal
+3.3V(H)
CN1-22
0V(L)
CN104-23 A[7] FLASH CARD Address Signal
+3.3V(H)
CN1-23
0V(L)
134
Pin No. Signal Name Destination Signal Waveform Function
CN104-24 A[6] FLASH CARD Address Signal
+3.3V(H)
CN1-24
0V(L)
CN104-25 A[5] FLASH CARD Address Signal
+3.3V(H)
DCN1-25
0V(L)
CN104-26 A[4] FLASH CARD Address Signal
+3.3V(H)
CN1-26
0V(L)
CN104-27 A[3] FLASH CARD Address Signal
+3.3V(H)
CN1-27
0V(L)
CN104-28 A[2] FLASH CARD Address Signal
+3.3V(H)
CN1-28
0V(L)
CN104-29 A[1] FLASH CARD Address Signal
+3.3V(H)
CN1-29
0V(L)
CN104-30 IOD[0] FLASH CARD +5V(H) Data Signal
CN1-30
0V(L)
CN104-31 IOD[1] FLASH CARD +5V(H) Data Signal
CN1-31
0V(L)
CN104-32 IOD[2] FLASH CARD +5V(H) Data Signal
CN1-32
0V(L)
CN104-33 nWRH FLASH CARD High Enable
+3.3V(H)
CN1-33 H: Disable
L: Enable
0V(L)
CN104-34 GND FLASH CARD Ground
CN1-34
0V
135
Pin No. Signal Name Destination Signal Waveform Function
CN104-36 nCD FLASH CARD 5V(H) Flash Card ID
CN1-36 H: Card Not Installed
L: Card Installed
0V(L)
0V(L)
CN104-38 IOD[12] FLASH CARD +5V(H) Data Signal
CN1-38
0V(L)
CN104-39 IOD[13] FLASH CARD +5V(H) Data Signal
CN1-39
0V(L)
CN104-40 IOD[14] FLASH CARD +5V(H) Data Signal
CN1-40
0V(L)
CN104-41 IOD[15] FLASH CARD +5V(H) Data Signal
CN1-41
0V(L)
CN104-42 n5VCS2 FLASH CARD +5V(H) Chip Select Signal
CN1-42
0V(L)
0V(L)
CN104-47 A[19] FLASH CARD Address Signal
+3.3V(H)
CN1-47
0V(L)
136
Pin No. Signal Name Destination Signal Waveform Function
CN104-48 A5V[20] FLASH CARD Address Signal
+5V(H)
CN1-48
0V(L)
0V(L)
0V(L)
0V(L)
137
Pin No. Signal Name Destination Signal Waveform Function
CN104-60 N.C. FLASH CARD Not Used
CN1-60
0V(L)
CN104-65 IOD[9] FLASH CARD +5V(H) Data Signal
CN1-65
0V(L)
CN104-66 IOD[10] FLASH CARD +5V(H) Data Signal
CN1-66
0V(L)
CN104-67 ID0 FLASH CARD Flash Card ID
CN1-67 +5V(H)
or
0V(L)
138
Pin No. Signal Name Destination Signal Waveform Function
CN106-3 FCK1 CCD PCB +3.3V Shift Register Clock
CN51-3
0V
CN106-4 FCK2 CCD PCB +3.3V Shift Register Clock
CN51-4
0V
CN106-5 FCP CCD PCB Clamp Clock
+3.3V
CN51-5
+0V
CN106-6 GND CCD PCB Ground
CN51-6
0V
0V
CN106-8 FR CCD PCB Reset Gate Clock
+3.3V
CN51-8
+0V
CN106-9 AGND CCD PCB Ground
CN51-9
0V
139
Pin No. Signal Name Destination Signal Waveform Function
CN106-15 +12V CCD PCB +12V +12 VDC Power Supply
CN51-15
0V
CN106-4 FCK2 CONS PCB +3.3V Shift Register Clock
CN57-4
0V
CN106-5 FCP CONS PCB Clamp Clock
+3.3V
CN57-5
+0V
CN106-6 GND CONS PCB Ground
CN57-6
0V
0V
CN106-8 FR CONS PCB Reset Gate Clock
+3.3V
CN57-8
+0V
CN106-9 AGND CONS PCB Ground
CN57-9
0V
140
Pin No. Signal Name Destination Signal Waveform Function
CN106-10 AGND CONS PCB Ground
DCN57-10
0V
CN107
Pin No. Signal Name Destination Signal Waveform Function
CN107-1 GND SDRM PCB Ground
CN1-1
0V
0V(L)
CN107-3 BMD[1] SDRM PCB +3.3V(H) Data Signal
CN1-3
0V(L)
CN107-4 BMD[2] SDRM PCB +3.3V(H) Data Signal
CN1-4
0V(L)
141
Pin No. Signal Name Destination Signal Waveform Function
CN107-5 BMD[3] SDRM PCB +3.3V(H) Data Signal
CN1-5
0V(L)
CN107-6 BMD[4] SDRM PCB +3.3V(H) Data Signal
CN1-6
0V(L)
CN107-7 BMD[5] SDRM PCB +3.3V(H) Data Signal
CN1-7
0V(L)
CN107-8 BMD[6] SDRM PCB +3.3V(H) Data Signal
CN1-8
0V(L)
CN107-9 BMD[7] SDRM PCB +3.3V(H) Data Signal
CN1-9
0V(L)
CN107-10 +3.3V SDRM PCB +3.3 VDC Power Supply
+3.3V
CN1-10
0V(L)
CN107-13 BMA[1] SDRM PCB +3.3V(H) Address Signal
CN1-13
0V(L)
CN107-14 BMA[2] SDRM PCB +3.3V(H) Address Signal
CN1-14
0V(L)
CN107-15 BMA[3] SDRM PCB +3.3V(H) Address Signal
CN1-15
0V(L)
142
Pin No. Signal Name Destination Signal Waveform Function
CN107-16 BMA[4] SDRM PCB +3.3V(H) Address Signal
CN1-16
0V(L)
CN107-17 BMA[5] SDRM PCB +3.3V(H) Address Signal
CN1-17
0V(L)
CN107-18 BMA[6] SDRM PCB +3.3V(H) Address Signal
CN1-18
0V(L)
CN107-19 BMA[10] SDRM PCB +3.3V(H) Address Signal
CN1-19
0V(L)
CN107-20 BMA[11] SDRM PCB +3.3V(H) Address Signal
CN1-20
0V(L)
CN107-21 BMD[8] SDRM PCB +3.3V(H) Data Signal
CN1-21
0V(L)
CN107-22 BMD[9] SDRM PCB +3.3V(H) Data Signal
CN1-22
0V(L)
CN107-23 BMD[10] SDRM PCB +3.3V(H) Data Signal
CN1-23
0V(L)
CN107-24 BMD[11] SDRM PCB +3.3V(H) Data Signal
CN1-24
0V(L)
CN107-25 BMD[12] SDRM PCB +3.3V(H) Data Signal
CN1-25
0V(L)
CN107-26 BMD[13] SDRM PCB +3.3V(H) Data Signal
CN1-26
0V(L)
143
Pin No. Signal Name Destination Signal Waveform Function
CN107-27 BMD[14] SDRM PCB +3.3V(H) Data Signal
CN1-27
0V(L)
CN107-28 BMA[7] SDRM PCB +3.3V(H) Address Signal
CN1-28
0V(L)
CN107-29 BMA[12] SDRM PCB +3.3V(H) Address Signal
CN1-29
0V(L)
CN107-30 +3.3V SDRM PCB +3.3 VDC Power Supply
+3.3V
CN1-30
0V(L)
CN107-32 BMA[9] SDRM PCB +3.3V(H) Address Signal
CN1-32
0V(L)
CN107-33 BBA[0] SDRM PCB +3.3V(H) S-DRAM Memory Area
CN1-33 Switching Signal
0V(L)
CN107-34 BBA[1] SDRM PCB +3.3V(H) S-DRAM Memory Area
CN1-34 Switching Signal
0V(L)
CN107-35 BMD[15] SDRM PCB +3.3V(H) Data Signal
CN1-35
0V(L)
CN107-36 nBDQML SDRM PCB +3.3V(H) Input/Output Mask Signal
CN1-36
0V(L)
CN107-37 N.C. SDRM PCB Not Used
CN1-37
144
Pin No. Signal Name Destination Signal Waveform Function
CN107-38 N.C. SDRM PCB Not Used
CN1-38
0V(L)
CN107-43 nBCS[3] SDRM PCB +3.3V(H) Chip Select Signal
CN1-43
0V(L)
CN107-44 nBCS[4] SDRM PCB Chip Select Signal
+3.3V
CN1-44
145
Pin No. Signal Name Destination Signal Waveform Function
CN107-50 N.C. SDRM PCB Not Used
CN1-50
0V
CN107-56 N.C. SDRM PCB Not Used
CN1-56
146
Pin No. Signal Name Destination Signal Waveform Function
CN107-62 N.C. SDRM PCB Not Used
CN1-62
0V
CN107-66 N.C. SDRM PCB Not Used
CN1-66
0V
CN107-68 SMEMID[0] SDRM PCB +3.3V(H) Memory ID
CN1-68
or ID0 ID1 ID2 ID3
0V(L) H H H H Not
Installed
L H H L 16MB
CN107-69 SMEMID[1] SDRM PCB +3.3V(H)
CN1-69
or
0V(L)
147
CN108
Pin No. Signal Name Destination Signal Waveform Function
CN108-1 +24V PNL1 PCB +24V +24 VDC Power Supply
CN65-1
0V
0V
0V
148
Pin No. Signal Name Destination Signal Waveform Function
CN108-12 nPSAVE PNL1 PCB Energy Saver Mode
Standby +5V
CN65-12 Transport Signal
Power Save 0V
0V
CN110
Pin No. Signal Name Destination Signal Waveform Function
CN110-1 +3.3V LSU PCB +3.3 VDC Power Supply
+3.3V
CN1
0V
CN110-4 -VDO LSU PCB 0.4 0.5V Video Signal (LVPS -
CN1 Output)
0V
CN113
Pin No. Signal Name Destination Signal Waveform Function
CN113-1 GND SDRM PCB Ground
CN1-1
0V
0V(L)
149
Pin No. Signal Name Destination Signal Waveform Function
CN113-3 BMD[1] SDRM PCB +3.3V(H) Data Signal
CN1-3
0V(L)
CN113-4 BMD[2] SDRM PCB +3.3V(H) Data Signal
CN1-4
0V(L)
CN113-5 BMD[3] SDRM PCB +3.3V(H) Data Signal
CN1-5
0V(L)
CN113-6 BMD[4] SDRM PCB +3.3V(H) Data Signal
CN1-6
0V(L)
CN113-7 BMD[5] SDRM PCB +3.3V(H) Data Signal
CN1-7
0V(L)
CN113-8 BMD[6] SDRM PCB +3.3V(H) Data Signal
CN1-8
0V(L)
CN113-9 BMD[7] SDRM PCB +3.3V(H) Data Signal
CN1-9
0V(L)
CN113-10 +3.3V SDRM PCB +3.3 VDC Power Supply
+3.3V
CN1-10
0V(L)
CN113-12 BMA[0] SDRM PCB +3.3V(H) Address Signal
CN1-12
0V(L)
CN113-13 BMA[1] SDRM PCB +3.3V(H) Address Signal
CN1-13
0V(L)
CN113-14 BMA[2] SDRM PCB +3.3V(H) Address Signal
CN1-14
0V(L)
150
Pin No. Signal Name Destination Signal Waveform Function
CN113-15 BMA[3] SDRM PCB +3.3V(H) Address Signal
CN1-15
0V(L)
CN113-16 BMA[4] SDRM PCB +3.3V(H) Address Signal
CN1-16
0V(L)
CN113-17 BMA[5] SDRM PCB +3.3V(H) Address Signal
CN1-17
0V(L)
CN113-18 BMA[6] SDRM PCB +3.3V(H) Address Signal
CN1-18
0V(L)
CN113-19 BMA[10] SDRM PCB +3.3V(H) Address Signal
CN1-19
0V(L)
CN113-20 BMA[11] SDRM PCB +3.3V(H) Address Signal
CN1-20
0V(L)
CN113-21 BMD[8] SDRM PCB +3.3V(H) Data Signal
CN1-21
0V(L)
CN113-22 BMD[9] SDRM PCB +3.3V(H) Data Signal
CN1-22
0V(L)
CN113-23 BMD[10] SDRM PCB +3.3V(H) Data Signal
CN1-23
0V(L)
CN113-24 BMD[11] SDRM PCB +3.3V(H) Data Signal
CN1-24
0V(L)
CN113-25 BMD[12] SDRM PCB +3.3V(H) Data Signal
CN1-25
0V(L)
CN113-26 BMD[13] SDRM PCB +3.3V(H) Data Signal
CN1-26
0V(L)
151
Pin No. Signal Name Destination Signal Waveform Function
CN113-27 BMD[14] SDRM PCB +3.3V(H) Data Signal
CN1-27
0V(L)
CN113-28 BMA[7] SDRM PCB +3.3V(H) Address Signal
CN1-28
0V(L)
CN113-29 BMA[12] SDRM PCB +3.3V(H) Address Signal
CN1-29
0V(L)
CN113-30 +3.3V SDRM PCB +3.3 VDC Power Supply
+3.3V
CN1-30
0V(L)
CN113-32 BMA[9] SDRM PCB +3.3V(H) Address Signal
CN1-32
0V(L)
CN113-33 BBA[0] SDRM PCB +3.3V(H) S-DRAM Memory Area
CN1-33 Switching Signal
0V(L)
CN113-34 BBA[1] SDRM PCB +3.3V(H) S-DRAM Memory Area
CN1-34 Switching Signal
0V(L)
CN113-35 BMD[15] SDRM PCB +3.3V(H) Data Signal
CN1-35
0V(L)
CN113-36 nBDQML SDRM PCB +3.3V(H) Input/Output Mask Signal
CN1-36
0V(L)
CN113-37 BMD[16] SDRM PCB +3.3V(H) Data Signal
CN1-37
0V(L)
CN113-38 BMD[17] SDRM PCB +3.3V(H) Data Signal
CN1-38
0V(L)
152
Pin No. Signal Name Destination Signal Waveform Function
CN113-39 GND SDRM PCB Ground
CN1-39
0V
0V(L)
CN113-43 BCS[3] SDRM PCB +3.3V(H) Chip Select Signal
CN1-43
0V(L)
CN113-44 BCS[4] SDRM PCB +3.3V(H) Chip Select Signal
CN1-44
0V(L)
CN113-45 BCS[5] SDRM PCB +3.3V(H) Chip Select Signal
CN1-45
0V(L)
CN113-46 nBRAS SDRM PCB +3.3V(H) S-DRAM Row Address
CN1-46 Strobe Command
0V(L)
CN113-47 nBMWT SDRM PCB +3.3V(H) S-DRAM Write Enable
CN1-47 H: Write Disable
L: Write Enable
0V(L)
CN113-48 nBCAS SDRM PCB +3.3V(H) S-DRAM Column Address
CN1-48 Strobe Command
0V(L)
CN113-49 BMD[18] SDRM PCB +3.3V(H) Data Signal
CN1-49
0V(L)
CN113-50 BMD[19] SDRM PCB +3.3V(H) Data Signal
CN1-50
0V(L)
153
Pin No. Signal Name Destination Signal Waveform Function
CN113-51 BMD[20] SDRM PCB +3.3V(H) Data Signal
CN1-51
0V(L)
CN113-52 BMD[21] SDRM PCB +3.3V(H) Data Signal
CN1-52
0V(L)
CN113-53 BMD[22] SDRM PCB +3.3V(H) Data Signal
CN1-53
0V(L)
CN113-54 BMD[23] SDRM PCB +3.3V(H) Data Signal
CN1-54
0V(L)
CN113-55 BDCLK[0] SDRM PCB +3.3V S-DRAM Access Clock
CN1-55
0V
CN113-56 BMD[24] SDRM PCB +3.3V(H) Data Signal
CN1-56
0V(L)
CN113-57 BMD[25] SDRM PCB +3.3V(H) Data Signal
CN1-57
0V(L)
CN113-58 BMD[26] SDRM PCB +3.3V(H) Data Signal
CN1-58
0V(L)
CN113-59 BMD[27] SDRM PCB +3.3V(H) Data Signal
CN1-59
0V(L)
CN113-60 BMD[28] SDRM PCB +3.3V(H) Data Signal
CN1-60
0V(L)
CN113-61 +3.3V SDRM PCB +3.3 VDC Power Supply
+3.3V
CN1-61
0V(L)
154
Pin No. Signal Name Destination Signal Waveform Function
CN113-63 BMD[30] SDRM PCB +3.3V(H) Data Signal
CN1-63
0V(L)
CN113-64 BMD[31] SDRM PCB +3.3V(H) Data Signal
CN1-64
0V(L)
CN113-65 BDCLK[1] SDRM PCB +3.3V S-DRAM Access Clock
CN1-65
0V
CN113-66 N.C. SDRM PCB Not Used
CN1-66
0V
CN113-68 SMEMID[0] SDRM PCB +3.3V(H) Memory ID
CN1-68 ID0 ID1 ID2 ID3
or
0V(L) H H H H Not
Installed
CN113-69 SMEMID[1] SDRM PCB L H H H 8MB
+3.3V(H)
CN1-69 L H H L 16MB
or L H L H 128MB
0V(L)
CN114
Pin No. Signal Name Destination Signal Waveform Function
CN114-1 +24V Fan +24V +24 VDC Power Supply
155
Pin No. Signal Name Destination Signal Waveform Function
CN114-2 MGND Fan Ground
0V
CN115
Pin No. Signal Name Destination Signal Waveform Function
CN115-1 +5VI PRIF PCB +5V +5 VDC Power Supply
CN212-1
0V(L)
CN115-4 IOD[1] PRIF PCB +5V(H) Data Signal
CN212-4
0V(L)
CN115-5 IOD[2] PRIF PCB +5V(H) Data Signal
CN212-5
0V(L)
CN115-6 IOD[3] PRIF PCB +5V(H) Data Signal
CN212-6
0V(L)
CN115-7 IOD[4] PRIF PCB +5V(H) Data Signal
CN212-7
0V(L)
CN115-8 IOD[5] PRIF PCB +5V(H) Data Signal
CN212-8
0V(L)
156
Pin No. Signal Name Destination Signal Waveform Function
CN115-9 IOD[6] PRIF PCB +5V(H) Data Signal
CN212-9
0V(L)
CN115-10 IOD[7] PRIF PCB +5V(H) Data Signal
CN212-10
0V(L)
CN115-11 IOD[8] PRIF PCB +5V(H) Data Signal
CN212-11
0V(L)
CN115-12 IOD[9] PRIF PCB +5V(H) Data Signal
CN212-12
0V(L)
CN115-13 IOD[10] PRIF PCB +5V(H) Data Signal
CN212-13
0V(L)
CN115-14 IOD[11] PRIF PCB +5V(H) Data Signal
CN212-14
0V(L)
CN115-15 IOD[12] PRIF PCB +5V(H) Data Signal
CN212-15
0V(L)
CN115-16 IOD[13] PRIF PCB +5V(H) Data Signal
CN212-16
0V(L)
CN115-17 IOD[14] PRIF PCB +5V(H) Data Signal
CN212-17
0V(L)
CN115-18 IOD[15] PRIF PCB +5V(H) Data Signal
CN212-18
0V(L)
CN115-19 GND PRIF PCB Ground
CN212-19
0V
157
Pin No. Signal Name Destination Signal Waveform Function
CN115-21 nDRAKS PRIF PCB +5V(H) DMA Accept Signal
CN212-21 H: Enable
L: Disable
0V(L)
CN116
Pin No. Signal Name Destination Signal Waveform Function
CN116-1 GND PRIF PCB Ground
CN211-1
0V
0V(L)
0V(L)
158
Pin No. Signal Name Destination Signal Waveform Function
CN116-7 nIRQBS1 PRIF PCB Printer Interrupt Signal
+5V(H)
CN211-7
0V(L)
CN116-8 nSENT PRIF PCB +5V(H) PRIF PCB Detection Signal
CN211-8 H: PRIF PCB Installed
L: PRIF PCB Installed
0V(L)
0V(L)
0V(L)
0V(L)
0V(L)
0V(L)
159
Pin No. Signal Name Destination Signal Waveform Function
CN116-18 GND PRIF PCB Ground
CN211-18
0V
CN118
Pin No. Signal Name Destination Signal Waveform Function
CN118-1 +24V RLB PCB +24V +24 VDC Power Supply
(Heater)
CN175-2
0V(L)
CN120-4 IOD[1] SORT PCB +5V(H) Data Signal
CN150-4
0V(L)
CN120-5 IOD[2] SORT PCB +5V(H) Data Signal
CN150-5
0V(L)
CN120-6 IOD[3] SORT PCB +5V(H) Data Signal
CN150-6
0V(L)
CN120-7 GND SORT PCB Ground
CN150-7
0V
160
Pin No. Signal Name Destination Signal Waveform Function
CN120-8 IOD[4] SORT PCB +5V(H) Data Signal
CN150-8
0V(L)
CN120-9 IOD[5] SORT PCB +5V(H) Data Signal
CN150-9
0V(L)
CN120-10 IOD[6] SORT PCB +5V(H) Data Signal
CN150-10
0V(L)
CN120-11 IOD[7] SORT PCB +5V(H) Data Signal
CN150-11
0V(L)
CN120-12 ARDY SORT PCB Not Used
+3.3V
CN150-12
0V(L)
0V(L)
0V(L)
161
Pin No. Signal Name Destination Signal Waveform Function
CN120-19 pIODREQ[6] SORT PCB Direct Memory Access Data
+3.3V(H)
CN150-19 Request Signal
H: Request
0V
0V
CN120-28 BID[9] SORT PCB +3.3V Image -BUS
CN150-28
0V
CN120-29 BID[10] SORT PCB +3.3V Image -BUS
CN150-29
0V
162
Pin No. Signal Name Destination Signal Waveform Function
CN120-30 BID[11] SORT PCB +3.3V Image -BUS
CN150-30
0V
CN120-31 GND SORT PCB Ground
CN150-31
0V
0V
CN120-33 BID[13] SORT PCB +3.3V Image -BUS
CN150-33
0V
CN120-34 BID[14] SORT PCB +3.3V Image -BUS
CN150-34
0V
CN120-35 BID[15] SORT PCB +3.3V Image -BUS
CN150-35
0V
CN120-36 AAD2 SORT PCB Not Used
CN150-36
163
Pin No. Signal Name Destination Signal Waveform Function
CN120-42 BRICLK SORT PCB +3.3V(H) Electronic Sorting Board
CN150-42 Clock Signal
0V
0V(L)
CN120-45 IOD[9] SORT PCB +5V(H) Data Signal
CN150-45
0V(L)
CN120-46 IOD[10] SORT PCB +5V(H) Data Signal
CN150-46
0V(L)
CN120-47 IOD[11] SORT PCB +5V(H) Data Signal
CN150-47
0V(L)
CN120-48 GND SORT PCB Ground
CN150-48
0V
0V(L)
CN120-50 IOD[13] SORT PCB +5V(H) Data Signal
CN150-50
0V(L)
CN120-51 IOD[14] SORT PCB +5V(H) Data Signal
CN150-51
0V(L)
CN120-52 IOD[15] SORT PCB +5V(H) Data Signal
CN150-52
0V(L)
CN120-53 SMEMID[0] SORT PCB Memory ID
CN150-53 +5V(H)
or
0V(L)
164
Pin No. Signal Name Destination Signal Waveform Function
CN120-54 AL[1] SORT PCB Address Signal
+5V(H)
CN150-54
0V(L)
0V(L)
0V(L)
0V(L)
0V(L)
0V(L)
0V(L)
0V(L)
165
Pin No. Signal Name Destination Signal Waveform Function
CN120-65 nSBACK SORT PCB Direct Memory Access BUS
+3.3V(H)
CN150-65 Receive Signal
H: Disable
0V(L) L: Enable
0V
CN120-69 BID[1] SORT PCB +3.3V Image -BUS
CN150-69
0V
CN120-70 BID[2] SORT PCB +3.3V Image -BUS
CN150-70
0V
CN120-71 BID[3] SORT PCB +3.3V Image -BUS
CN150-71
0V
CN120-72 SMEMID[2] SORT PCB Memory ID
CN150-72
+5V(H)
or
0V(L)
0V
CN120-74 BID[5] SORT PCB +3.3V Image -BUS
CN150-74
0V
CN120-75 BID[6] SORT PCB +3.3V Image -BUS
CN150-75
0V
166
Pin No. Signal Name Destination Signal Waveform Function
CN120-76 BID[7] SORT PCB +3.3V Image -BUS
CN150-76
0V
CN120-77 N.C. SORT PCB Not Used
CN150-77
CN121
Pin No. Signal Name Destination Signal Waveform Function
CN121-1 +5VI EP PCB +5V +5 VDC Power Supply
CN1-1
0V(L)
0V(L)
0V(L)
0V(L)
167
Pin No. Signal Name Destination Signal Waveform Function
CN121-7 AL[9] EP PCB Address Signal
+5V(H)
CN1-7
0V(L)
0V(L)
0V(L)
0V(L)
0V(L)
168
Pin No. Signal Name Destination Signal Waveform Function
CN121-19 IOD[0] EP PCB +5V(H) Data Signal
CN1-19
0V
CN121-20 IOD[1] EP PCB +5V(H) Data Signal
CN1-20
0V
CN121-21 IOD[4] EP PCB +5V(H) Data Signal
CN1-21
0V
CN121-22 IOD[5] EP PCB +5V(H) Data Signal
CN1-22
0V
CN121-23 IOD[8] EP PCB +5V(H) Data Signal
CN1-23
0V
CN121-24 IOD[9] EP PCB +5V(H) Data Signal
CN1-24
0V
CN121-25 IOD[12] EP PCB +5V(H) Data Signal
CN1-25
0V
CN121-26 IOD[13] EP PCB +5V(H) Data Signal
CN1-26
0V
CN121-27 nWAIT[2] EP PCB BUS Wait Signal
+5V(H)
CN1-27
0V(L)
0V(L)
169
Pin No. Signal Name Destination Signal Waveform Function
CN121-30 nOPB2 EP PCB Option Detection Signal
CN1-30 +5V(H) H: Option Not Installed
or L: Option Installed
0V(L)
0V
CN121-40 PD[1] EP PCB +5V(H) Data Signal
CN1-40
0V
CN121-41 PD[4] EP PCB +5V(H) Data Signal
CN1-41
0V
170
Pin No. Signal Name Destination Signal Waveform Function
CN121-42 PD[5] EP PCB +5V(H) Data Signal
CN1-42
0V
CN121-43 GND EP PCB Ground
CN1-43
0V
0V
CN121-46 PD[9] EP PCB +5V(H) Data Signal
CN1-46
0V
CN121-47 PD[12] EP PCB +5V(H) Data Signal
CN1-47
0V
CN121-48 PD[13] EP PCB +5V(H) Data Signal
CN1-48
0V
CN121-49 GND EP PCB Ground
CN1-49
0V
0V(L)
171
Pin No. Signal Name Destination Signal Waveform Function
CN121-54 AL[4] EP PCB Address Signal
+5V(H)
CN1-54
0V(L)
0V(L)
0V(L)
0V(L)
0V(L)
0V(L)
172
Pin No. Signal Name Destination Signal Waveform Function
CN121-66 nMIRQPDL EP PCB Interrupt Request Signal
+5V(H)
CN1-66 H: Disable
L: Enable
0V(L)
0V
CN121-68 IOD[3] EP PCB +5V(H) Data Signal
CN1-68
0V
CN121-69 IOD[6] EP PCB +5V(H) Data Signal
CN1-69
0V
CN121-70 IOD[7] EP PCB +5V(H) Data Signal
CN1-70
0V
CN121-71 IOD[10] EP PCB +5V(H) Data Signal
CN1-71
0V
CN121-72 IOD[11] EP PCB +5V(H) Data Signal
CN1-72
0V
CN121-73 IOD[14] EP PCB +5V(H) Data Signal
CN1-73
0V
CN121-74 IOD[15] EP PCB +5V(H) Data Signal
CN1-74
0V
CN121-75 pOP2RST EP PCB +5V(H) Reset Signal
CN1-75 H: Reset
L: Not Reset
0V
CN121-76 pOP3RST EP PCB +5V(H) Reset Signal
CN1-76 H: Reset
L: Not Reset
0V
173
Pin No. Signal Name Destination Signal Waveform Function
CN121-77 nOPB3 EP PCB Option Detection Signal
CN1-77 +5V(H) H: Option Not Installed
or L: Option Installed
0V(L)
0V
CN121-80 N.C. EP PCB Not Used
CN1-80
0V(L)
174
Pin No. Signal Name Destination Signal Waveform Function
CN121-89 PD[2] EP PCB +5V(H) Data Signal
CN1-89
0V
CN121-90 PD[3] EP PCB +5V(H) Data Signal
CN1-90
0V
CN121-91 PD[6] EP PCB +5V(H) Data Signal
CN1-91
0V
CN121-92 PD[7] EP PCB +5V(H) Data Signal
CN1-92
0V
CN121-93 GND EP PCB Ground
CN1-93
0V
0V
CN121-96 PD[11] EP PCB +5V(H) Data Signal
CN1-96
0V
CN121-97 PD[14] EP PCB +5V(H) Data Signal
CN1-97
0V
CN121-98 PD[15] EP PCB +5V(H) Data Signal
CN1-98
0V
CN121-99 +5V EP PCB +5V +5 VDC Power Supply
CN1-99
175
CN122
Pin No. Signal Name Destination Signal Waveform Function
CN122-1 +24V FXB PCB +24V +24 VDC Power Supply
CN160-1
OFF 0V(L)
0V(L)
176
Pin No. Signal Name Destination Signal Waveform Function
CN122-12 nHKOF FXB PCB External Phone Off-Hook
+5V(H)
CN160-12 Detection Signal
0V(L)
0V(L)
0V(L)
0V(L)
177
Pin No. Signal Name Destination Signal Waveform Function
CN122-23 IOD9 FXB PCB +5V(H) Data Signal
CN160-23
0V(L)
CN122-24 IOD10 FXB PCB +5V(H) Data Signal
CN160-24
0V(L)
CN122-25 IOD11 FXB PCB +5V(H) Data Signal
CN160-25
0V(L)
CN122-26 IOD12 FXB PCB +5V(H) Data Signal
CN160-26
0V(L)
CN122-27 IOD13 FXB PCB +5V(H) Data Signal
CN160-27
0V(L)
CN122-28 IOD14 FXB PCB +5V(H) Data Signal
CN160-28
0V(L)
CN122-29 IOD15 FXB PCB +5V(H) Data Signal
CN160-29
0V(L)
CN122-30 nCS11 FXB PCB Chip Select Signal
+5V(H)
CN160-30
0V(L)
0V(L)
0V
178
Pin No. Signal Name Destination Signal Waveform Function
CN122-34 AL[0] FXB PCB Address Signal
+5V(H)
CN160-34
0V(L)
0V(L)
0V(L)
0V(L)
0V(L)
0V(L)
0V(L)
0V
CN122-43 A[16] FXB PCB +3.3V Address Signal
CN160-43
0V
CN122-44 A[17] FXB PCB +3.3V Address Signal
CN160-44
0V
179
Pin No. Signal Name Destination Signal Waveform Function
CN122-45 A[20] FXB PCB +3.3V Address Signal
CN160-45
0V
CN122-46 nFXBOPT FXB PCB Fax Option Detection Signal
CN160-46
+5V(H) H: Option Not Installed
or L: Option Installed
0V(L)
0V
CN122-48 nMDRST FXB PCB +5V(H) Modem Reset Signal
CN160-48
0V(L)
180
Pin No. Signal Name Destination Signal Waveform Function
CN122-57 nVOL0 FXB PCB Monitor Volume
CN160-57 +5V(H)
or
0V(L)
OFF 0V(L)
OFF 0V(L)
OFF 0V(L)
OFF 0V(L)
181
Pin No. Signal Name Destination Signal Waveform Function
CN122-68 IOD[0] FXB PCB +5V(H) Data Signal
CN160-68
0V(L)
CN122-69 IOD[1] FXB PCB +5V(H) Data Signal
CN160-69
0V(L)
CN122-70 IOD[2] FXB PCB +5V(H) Data Signal
CN160-70
0V(L)
CN122-71 IOD[3] FXB PCB +5V(H) Data Signal
CN160-71
0V(L)
CN122-72 IOD[4] FXB PCB +5V(H) Data Signal
CN160-72
0V(L)
CN122-73 IOD[5] FXB PCB +5V(H) Data Signal
CN160-73
0V(L)
CN122-74 IOD[6] FXB PCB +5V(H) Data Signal
CN160-74
0V(L)
CN122-75 IOD[7] FXB PCB +5V(H) Data Signal
CN160-75
0V(L)
CN122-76 nCS00 FXB PCB Modem Control Signal
+5V(H)
CN160-76
0V(L)
182
Pin No. Signal Name Destination Signal Waveform Function
CN122-79 nACK[1] FXB PCB +5V(H) Modem ACK[1] Signal
CN160-79
0V(L)
0V
0V
0V(L)
0V(L)
0V(L)
0V(L)
0V(L)
0V(L)
183
Pin No. Signal Name Destination Signal Waveform Function
CN122-90 A[14] FXB PCB +3.3V Address Signal
CN160-90
0V
CN122-91 A[15] FXB PCB +3.3V Address Signal
CN160-91
0V
CN122-92 A[18] FXB PCB +3.3V Address Signal
CN160-92
0V
CN122-93 A[19] FXB PCB +3.3V Address Signal
CN160-93
0V
CN122-94 nFAXDET FXB PCB Fax Option Detection Signal
CN160-94
+5V(H) H: Option Not Installed
or L: Option Installed
0V(L)
0V(L)
CN122-96 n5VRD FXB PCB CPU Read Signal
+3.3V(H)
CN160-96 H: Read Disable
L: Read Enable
0V(L)
184
CN123
Pin No. Signal Name Destination Signal Waveform Function
CN123-1 +5VI G3B PCB +5V +5 VDC Power Supply
CN131-1
or
LANB PCB
CN2-1
CN123-2 +5VI G3B PCB +5V +5 VDC Power Supply
CN131-2
or
LANB PCB
CN2-2
CN123-3 AL[1] G3B PCB Address Signal
CN131-3 +5V
or
LANB PCB 0V
CN2-3
CN123-4 AL[2] G3B PCB Address Signal
CN131-4 +5V
or
LANB PCB 0V
CN2-4
CN123-5 AL[5] G3B PCB Address Signal
CN131-5 +5V
or
LANB PCB 0V
CN2-5
CN123-6 AL[6] G3B PCB Address Signal
CN131-6 +5V
or
LANB PCB 0V
CN2-6
CN123-7 AL[9] G3B PCB Address Signal
CN131-7 +5V
or
LANB PCB 0V
CN2-7
CN123-8 AL[10] G3B PCB Address Signal
CN131-8 +5V
or
LANB PCB 0V
CN2-8
CN123-9 nWAIT G3B PCB +5V(H) BUS Wait Signal
CN131-9
or
LANB PCB 0V(L)
CN2-9
CN123-10 N.C. G3B PCB Not Used
CN131-10
or
LANB PCB
CN2-10
185
Pin No. Signal Name Destination Signal Waveform Function
CN123-11 nCS08 G3B PCB +5V(H) Chip Enable Signal
CN131-11 H: Disable
or L: Enable
LANB PCB 0V(L)
CN2-11
CN123-12 nCS0E G3B PCB +5V(H) Chip Enable Signal
CN131-12 H: Disable
or L: Enable
LANB PCB 0V(L)
CN2-12
CN123-13 nIOWRH G3B PCB +5V(H) I/O Write (High) Signal
CN131-13 H: Write Disable
or L: Write Enable
LANB PCB 0V(L)
CN2-13
CN123-14 GND G3B PCB Ground
CN131-14
or 0V
LANB PCB
CN2-14
CN123-15 nIRQOP1 G3B PCB +5V(H) Interrupt Signal
CN131-15
or
LANB PCB 0V(L)
CN2-15
CN123-16 nIRQOP2 G3B PCB +5V(H) Interrupt Signal
CN131-16
or
LANB PCB 0V(L)
CN2-16
CN123-17 N.C. G3B PCB Not Used
CN131-17
or
LANB PCB
CN2-17
CN123-18 pOP1RST G3B PCB +3.3V(H) Reset Signal
CN131-18 H: Reset
or L: Not Reset
LANB PCB 0V(L)
CN2-18
CN123-19 IOD[0] G3B PCB +5V(H) Data Signal
CN131-19
or
LANB PCB 0V(L)
CN2-19
CN123-20 IOD[1] G3B PCB +5V(H) Data Signal
CN131-20
or
LANB PCB 0V(L)
CN2-20
186
Pin No. Signal Name Destination Signal Waveform Function
CN123-21 IOD[4] G3B PCB +5V(H) Data Signal
CN131-21
or
LANB PCB 0V(L)
CN2-21
CN123-22 IOD[5] G3B PCB +5V(H) Data Signal
CN131-22
or
LANB PCB 0V(L)
CN2-22
CN123-23 IOD[8] G3B PCB +5V(H) Data Signal
CN131-23
or
LANB PCB 0V(L)
CN2-23
CN123-24 IOD[9] G3B PCB +5V(H) Data Signal
CN131-24
or
LANB PCB 0V(L)
CN2-24
CN123-25 IOD[12] G3B PCB +5V(H) Data Signal
CN131-25
or
LANB PCB 0V(L)
CN2-25
CN123-26 IOD[13] G3B PCB +5V(H) Data Signal
CN131-26
or
LANB PCB 0V(L)
CN2-26
CN123-27 nWAIT[2] G3B PCB +5V(H) BUS Wait Signal
CN131-27
or
LANB PCB 0V(L)
CN2-27
CN123-28 nWAIT[3] G3B PCB +5V(H) BUS Wait Signal
CN131-28
or
LANB PCB 0V(L)
CN2-28
CN123-29 nOPB1 G3B PCB Option Detection Signal
CN131-29 +5V(H) H: Option Not Installed
or or L: Option Installed
LANB PCB 0V(L)
CN2-29
CN123-30 nOPB2 G3B PCB Option Detection Signal
CN131-30
+5V(H) H: Option Not Installed
or or L: Option Installed
LANB PCB 0V(L)
CN2-30
187
Pin No. Signal Name Destination Signal Waveform Function
CN123-31 N.C. G3B PCB Not Used
CN131-31
or
LANB PCB
CN2-31
CN123-32 N.C. G3B PCB Not Used
CN131-32
or
LANB PCB
CN2-32
CN123-33 +5VP G3B PCB +5V +5 VDC Pilot Power Supply,
CN131-33 that provides power to the
or active components during
LANB PCB the Sleep Mode.
CN2-33
CN123-34 +24VF G3B PCB +24V +24 VDC Power Supply
CN131-34
or
LANB PCB
CN2-34
CN123-35 GND G3B PCB Ground
CN131-35
or 0V
LANB PCB
CN2-35
CN123-36 GND G3B PCB Ground
CN131-36
or 0V
LANB PCB
CN2-36
CN123-37 AL[3] G3B PCB Address Signal
CN131-37 +5V
or
LANB PCB 0V
CN2-37
CN123-38 AL[4] G3B PCB Address Signal
CN131-38 +5V
or
LANB PCB 0V
CN2-38
CN123-39 AL[7] G3B PCB Address Signal
CN131-39 +5V
or
LANB PCB 0V
CN2-39
CN123-40 AL[8] G3B PCB Address Signal
CN131-40 +5V
or
LANB PCB 0V
CN2-40
188
Pin No. Signal Name Destination Signal Waveform Function
CN123-41 AL[11] G3B PCB Address Signal
CN131-41 +5V
or
LANB PCB 0V
CN2-41
CN123-42 AL[12] G3B PCB Address Signal
CN131-42 +5V
or
LANB PCB 0V
CN2-42
CN123-43 nCS09 G3B PCB +5V(H) Chip Enable Signal
CN131-43 H: Disable
or L: Enable
LANB PCB 0V(L)
CN2-43
CN123-44 nCS0A G3B PCB +5V(H) Chip Enable Signal
CN131-44 H: Disable
or L: Enable
LANB PCB 0V(L)
CN2-44
CN123-45 nIORD G3B PCB +5V(H) I/O Read Signal
CN131-45 H: Read Disable
or L: Read Enable
LANB PCB 0V(L)
CN2-45
CN123-46 nIOWRL G3B PCB +5V(H) I/O Write (Low) Signal
CN131-46 H: Write Disable
or L: Write Enable
LANB PCB 0V(L)
CN2-46
CN123-47 nWAIT[1] G3B PCB +5V(H) BUS Wait Signal
CN131-47
or
LANB PCB 0V(L)
CN2-47
CN123-48 N.C. G3B PCB Not Used
CN131-48
or
LANB PCB
CN2-48
CN123-49 N.C. G3B PCB Not Used
CN131-49
or
LANB PCB
CN2-49
CN123-50 nMIRQPDL G3B PCB Interrupt Request Signal
+5V(H)
CN131-50 H: Disable
or L: Enable
LANB PCB 0V
CN2-50
189
Pin No. Signal Name Destination Signal Waveform Function
CN123-51 IOD[2] G3B PCB +5V(H) Data Signal
CN131-51
or
LANB PCB 0V(L)
CN2-51
CN123-52 IOD[3] G3B PCB +5V(H) Data Signal
CN131-52
or
LANB PCB 0V(L)
CN2-52
CN123-53 IOD[6] G3B PCB +5V(H) Data Signal
CN131-53
or
LANB PCB 0V(L)
CN2-53
CN123-54 IOD[7] G3B PCB +5V(H) Data Signal
CN131-54
or
LANB PCB 0V(L)
CN2-54
CN123-55 IOD[10] G3B PCB +5V(H) Data Signal
CN131-55
or
LANB PCB 0V(L)
CN2-55
CN123-56 IOD[11] G3B PCB +5V(H) Data Signal
CN131-56
or
LANB PCB 0V(L)
CN2-56
CN123-57 IOD[14] G3B PCB +5V(H) Data Signal
CN131-57
or
LANB PCB 0V(L)
CN2-57
CN123-58 IOD[15] G3B PCB +5V(H) Data Signal
CN131-58
or
LANB PCB 0V(L)
CN2-58
CN123-59 pOP2RST G3B PCB +3.3V(H) Reset Signal
CN131-59 H: Reset
or L: Not Reset
LANB PCB 0V(L)
CN2-59
CN123-60 pOP3RST G3B PCB +3.3V(H) Reset Signal
CN131-60 H: Reset
or L: Not Reset
LANB PCB 0V(L)
CN2-60
190
Pin No. Signal Name Destination Signal Waveform Function
CN123-61 nOPB3 G3B PCB Option Detection Signal
CN131-61 +5V(H) G3B or LANB Option
or or Detection Signal
LANB PCB 0V(L) L: Option Not Installed
CN2-61 H: Option Installed
CN123-62 N.C. G3B PCB Not Used
CN131-62
or
LANB PCB
CN2-62
CN123-63 nPSDES G3B PCB Energy Saver Mode Disable
+5V(H)
CN131-63 Signal
or
LANB PCB 0V(L)
CN2-63
CN123-64 N.C. G3B PCB Not Used
CN131-64
or
LANB PCB
CN2-64
CN123-65 nOPON G3B PCB Option Detection Signal
CN131-65
+5V(H) H: Option Not Installed
or or L: Option Installed
LANB PCB 0V(L)
CN2-65
CN123-66 +3.3V G3B PCB +3.3 VDC Power Supply
+3.3V
CN131-66
or
LANB PCB
CN2-66
CN123-67 -12V G3B PCB -12 VDC Power Supply
CN131-67
or
LANB PCB -12V
CN2-67
CN123-68 AGND G3B PCB Ground
CN131-68
or 0V
LANB PCB
CN2-68
CN125
Pin No. Signal Name Destination Signal Waveform Function
CN125-1 SPKOUT SPEAKER +1V Monitor Signal
(Max)
-1V
(Min)
CN125-2 GND SPEAKER Ground
0V
191
3.7. PNL1 PC Board
CN61
Pin No. Signal Name Destination Signal Waveform Function
CN61-1 VLCD LCD Module-1 LCD Drive Volume Voltage
21.6V 23.6V
0V
CN61-4 D2 LCD Module-4 Data Signal
+5V
0V
CN61-5 D1 LCD Module-5 Data Signal
+5V
0V
CN61-6 D0 LCD Module-6 Data Signal
+5V
0V
CN61-7 nDSPOFF LCD Module-7 Display Off Signal
+5V Display L: Display Off
ON Display
0V OFF
0V
0V
0V
192
Pin No. Signal Name Destination Signal Waveform Function
CN61-12 FRM LCD Module-12 Frame Signal
+5V
0V
CN62
Pin No. Signal Name Destination Signal Waveform Function
CN62-1 +24V INVERTER +24V +24 VDC Power Supply
CN1-1
CN63
Pin No. Signal Name Destination Signal Waveform Function
CN63-1 X1 Touch Panel-1 Touch Panel Matrix Signal
+5V
0V
0V
0V
CN65
Refer to SC PC Board CN108.
CN66
Pin No. Signal Name Destination Signal Waveform Function
CN66-1 +24VD PNL3 PCB +24V +24 VDC Power Supply
CN70-1
193
Pin No. Signal Name Destination Signal Waveform Function
CN66-2 VLCD PNL3 PCB LCD Drive Volume Voltage
CN70-2
21.6V 23.6V
0V
CN66-5 SCN[1] PNL3 PCB Key Scan Signal
CN70-5 +5V
0V
CN66-6 KEYIN0 PNL3 PCB Key Scan Signal
CN70-6 +5V
0V
CN66-7 KEYIN1 PNL3 PCB Key Scan Signal
CN70-7 +5V
0V
CN66-8 KEYIN2 PNL3 PCB Key Scan Signal
CN70-8 +5V
0V
CN66-9 LEDCT0 PNL3 PCB LED Matrix Signal
CN70-9 +5V
0V
CN66-10 LEDCT1 PNL3 PCB LED Matrix Signal
CN70-10 +5V
0V
CN66-11 LED0 PNL3 PCB LED Matrix Signal
CN70-11 +5V
ON
OFF
0V
194
Pin No. Signal Name Destination Signal Waveform Function
CN66-13 LED2 PNL3 PCB LED Matrix Signal
CN70-13 +5V
ON
OFF
0V
CN67
Pin No. Signal Name Destination Signal Waveform Function
CN67-1 BUZCLK PNL2 PCB Buzzer Clock
CN69-1 +24V
0V
CN67-2 SCN1 PNL2 PCB Key Scan Signal
CN69-2 +5V
0V
CN67-3 SCN2 PNL2 PCB Key Scan Signal
CN69-3 +5V
0V
CN67-4 SCN3 PNL2 PCB Key Scan Signal
CN69-4 +5V
0V
CN67-5 SCN4 PNL2 PCB Key Scan Signal
CN69-5 +5V
0V
CN67-6 SCN5 PNL2 PCB Key Scan Signal
CN69-6 +5V
0V
CN67-7 KEYIN0 PNL2 PCB Key Scan Signal
CN69-7 +5V
0V
CN67-8 KEYIN1 PNL2 PCB Key Scan Signal
CN69-8 +5V
0V
CN67-9 KEYIN2 PNL2 PCB Key Scan Signal
CN69-9 +5V
0V
195
Pin No. Signal Name Destination Signal Waveform Function
CN67-10 KEYIN3 PNL2 PCB Key Scan Signal
CN69-10 +5V
0V
CN67-11 KEYIN4 PNL2 PCB Key Scan Signal
CN69-11 +5V
0V
CN67-12 KEYIN5 PNL2 PCB Key Scan Signal
CN69-12 +5V
0V
CN67-13 KEYIN6 PNL2 PCB Key Scan Signal
CN69-13 +5V
0V
CN67-14 KEYIN7 PNL2 PCB Key Scan Signal
CN69-14 +5V
0V
CN67-15 LEDCT0 PNL2 PCB LED Matrix Signal
CN69-15 +5V
0V
CN67-16 LEDCT1 PNL2 PCB LED Matrix Signal
CN69-16 +5V
0V
CN67-17 LED4 PNL2 PCB LED Matrix Signal
CN69-17 +5V
ON
OFF
0V
196
Pin No. Signal Name Destination Signal Waveform Function
CN67-21 BAT PNL2 PCB Battery Voltage
CN69-21
0V +3V
CN68
Pin No. Signal Name Destination Signal Waveform Function
CN68-1 GND FG Ground
0V
197
3.8. PNL2 PC Board
CN69
Refer to PNL1 PC Board CN67
198
3.9. PNL3 PC Board
CN70
Refer to PNL1 PC Board CN66.
199
3.10. PNL4 PC Board
CN61
Pin No. Signal Name Destination Signal Waveform Function
CN61-1 V0 LCD Module-1 +0.16 VDC Power Supply
+0.16V
0V
0V
CN61-5 DB[6] LCD Module-5 Data Signal
+5V
0V
CN61-6 DB[5] LCD Module-6 Data Signal
+5V
0V
CN61-7 DB[4] LCD Module-7 Data Signal
+5V
0V
CN61-8 DB[3] LCD Module-8 Data Signal
+5V
0V
CN61-9 DB[2] LCD Module-9 Data Signal
+5V
0V
CN61-10 DB[1] LCD Module-10 Data Signal
+5V
0V
CN61-11 DB[0] LCD Module-11 Data Signal
+5V
0V
200
Pin No. Signal Name Destination Signal Waveform Function
CN61-12 E LCD Module-12 Data Read/Write Enable
+5V Signal
H: Enable
0V L: Disable
CN61-13 R/W LCD Module-12 Data Read/Write Select
+5V Signal
H: Read
0V L: Write
CN61-14 RS LCD Module-12 Resister Select Signal
+5V H: Data Register
L: Instruction Register
0V
CN62
Pin No. Signal Name Destination Signal Waveform Function
CN62-1 SCN[1] PNL4 PCB Key Scan Signal
CN63-1 +5V
0V
CN62-2 KIN[1] PNL4 PCB Key Scan Signal
CN63-2 +5V
0V
CN62-3 KIN[2] PNL4 PCB Key Scan Signal
CN63-3 +5V
0V
CN62-4 KIN[6] PNL4 PCB Key Scan Signal
CN63-4 +5V
0V
CN62-5 LV[0] PNL4 PCB LED Matrix Signal
CN63-5 +5V
ON
OFF
0V
201
Pin No. Signal Name Destination Signal Waveform Function
CN62-9 LV[5] PNL4 PCB LED Matrix Signal
CN63-9 +5V
ON
OFF
0V
0V
CN62-14 N.C.
CN63
Refer to PNL4 PC Board CN62.
CN65
Refer to SC PC Board CN108.
CN67
Refer to PNL1 PC Board CN67.
202
3.11. SCN PC Board
CN2
Refer to SC PC Board CN103.
CN3
Pin No. Signal Name Destination Signal Waveform Function
CN3-1 +5VP ADF PCB +5V +5 VDC Power Supply
CN21-1
ON 0V
CN3-6 N.C. ADF PCB Not Used
CN21-6
203
Pin No. Signal Name Destination Signal Waveform Function
CN3-11 nAB2SN ADF PCB Duplex Eject Detection
CN21-11 +5V Signal
L: Detect
ON
0V
CN3-12 nAB1SN ADF PCB Read Point Detection Signal
CN21-12 +5V L: Detect
ON
0V
CN3-13 nAEJC ADF PCB Original Eject Detection
CN21-13 +5V Signal
L: Detect
ON
0V
CN3-14 nAREV ADF PCB ADF Exit Cover Open
CN21-14 +5V Detection Signal
L: Detect
ON
0V
CN3-15 nAOAC ADF PCB ADF Cover Open Detection
CN21-15 +5V Signal
L: Detect
ON
0V
CN3-16 pKEEP1 ADF PCB ADF Document Stopper
+5V
CN21-16 Solenoid Control Signal
ON 0V
CN3-17 pKEEP2 ADF PCB ADF Document Stopper
+5V
CN21-17 Solenoid Control Signal
ON 0V
CN3-18 pAPACHG ADF PCB Duplex 2 Guide Solenoid
+5V
CN21-18 Control Signal
ON 0V
CN3-19 pAPICR ADF PCB Release Lever Plate
+5V
CN21-19 Solenoid Control Signal
ON 0V
CN3-20 pASTAMP ADF PCB ADF Stamp Solenoid
+5V
CN21-20 Control Signal
ON 0V
CN3-21 pACLH1 ADF PCB Feed 2 Roller Clutch Control
+5V
CN21-21 Signal
ON 0V
204
Pin No. Signal Name Destination Signal Waveform Function
CN3-22 pACLH2 ADF PCB ADF Roller Clutch Control
+5V
CN21-22 Signal
ON 0V
CN3-23 pACLH3 ADF PCB Inverting Roller Clutch
+5V
CN21-23 Control Signal
ON 0V
CN3-24 nACLOCKAD1 ADF PCB ADF Motor Control Clock
CN21-24 +5V Signal
0V
0V
0V
0V
205
Pin No. Signal Name Destination Signal Waveform Function
CN3-34 MGND ADF PCB Ground
CN21-34
0V
CN6
Pin No. Signal Name Destination Signal Waveform Function
CN6-1 ORISENCMN Home Position +2.8V Sensor +2.8 VDC Power
Sensor Supply
CN7
Pin No. Signal Name Destination Signal Waveform Function
CN7-1 LEDA Size Sensor 3 Select Sensor Signal
+5V
0V
206
Pin No. Signal Name Destination Signal Waveform Function
CN7-2 LEDB Size Sensor 3 Select Sensor Signal
+5V
0V
CN7-3 LEDC Size Sensor 3 Select Sensor Signal
+5V
0V
CN7-4 +5V Size Sensor 3 +5V +5 VDC Power Supply
0V
0V
0V
CN7-8 LEDX Size Sensor 3 Select Sensor Signal
+5V
0V
CN7-9 LEDY Size Sensor 3 Select Sensor Signal
+5V
0V
CN7-10 LEDZ Size Sensor 1 & 3 Select Sensor Signal
+5V
0V
CN7-11 +5V Size Sensor 1 & 3 +5V +5 VDC Power Supply
0V
0V
207
Pin No. Signal Name Destination Signal Waveform Function
CN7-14 VOUTX Size Sensor 3 +5V Sensor Control Signal
0V
CN8
Pin No. Signal Name Destination Signal Waveform Function
CN8-1 OUTA Stepping Motor +24V Motor Control Signal
0V
CN8-2 +24V Stepping Motor +24V +24 VDC Power Supply
0V
CN8-4 OUTB Stepping Motor +24V Motor Control Signal
0V
CN8-5 +24V Stepping Motor +24V +24 VDC Power Supply
0V
CN9
Pin No. Signal Name Destination Signal Waveform Function
CN9-1 nFLON INV +5V (H) Inverter Ground
CN1-1 OFF
0V (L)
ON
CN9-2 FLNG INV Inverter Control Signal
CN1-2 ON +0.7V
0V OFF
208
3.12. LPC PC Board
CN701
Pin No. Signal Name Destination Signal Waveform Function
CN701-1 nS/H LSU +5V Sample Hold Signal
CN2-1
0V
CN701-2 nHSYNC LSU +5V Horizontal Synchronous
CN2-2 Signal
0V
CN701-3 L+5V LSU +5V Laser Circuit +5 VDC Power
CN2-3 Supply
0V (L)
0V
2.0V
0V
CN701-10 nPMRDY LSU Polygon Motor Ready Signal
CN3-2
+5V (H)
0V (L)
0V (L)
209
Pin No. Signal Name Destination Signal Waveform Function
CN701-12 MGND LSU Ground
CN3-4
0V
CN702
Pin No. Signal Name Destination Signal Waveform Function
CN702-1 +24V LVPS +24V +24 VDC Power Supply
CN62-1
210
Pin No. Signal Name Destination Signal Waveform Function
CN702-11 GND LVPS Ground
CN62-11
0V
CN703
Pin No. Signal Name Destination Signal Waveform Function
CN703-1 +24V Micro Switch +24V +24 VDC Power Supply
CN705
Pin No. Signal Name Destination Signal Waveform Function
CN705-1 GND TONER SENSOR Ground
0V
0V
0V (L)
211
CN706
Pin No. Signal Name Destination Signal Waveform Function
CN706-1 +24VM Lift DC Motor-1 +24V +24 VDC Power Supply
0V
0V
0V
0V
212
Pin No. Signal Name Destination Signal Waveform Function
CN707-10 nOPSBSY CST2 PCB +5V Paper Tray Status Busy
CN770-12 Signal
H: Status Not Busy
0V L: Status Busy
0V
0V
0V
0V
213
Pin No. Signal Name Destination Signal Waveform Function
CN707-21 nCSTOP CST2 PCB 2nd Paper Feed Module
CN771-9 Detection Signal
0V
0V
0V
214
Pin No. Signal Name Destination Signal Waveform Function
CN707-8 nOPCLK CST2 PCB +5V Paper Tray Command
CN770-10 Status Clock Signal
0V
0V
0V
0V
0V
215
Pin No. Signal Name Destination Signal Waveform Function
CN707-19 nFDPCHK2 CST2 PCB 2nd Paper Tray Paper
CN771-7 +5V Registration Detection
Signal
0V L: Detect
CN708
Pin No. Signal Name Destination Signal Waveform Function
CN708-1 +24VD1 Front Cover +24V +24 VDC Power Supply
Sensor-1
(ILS PCB)
216
Pin No. Signal Name Destination Signal Waveform Function
CN708-4 nACSW HTC PCB Relay Control Signal
CN765-1 +24V
0V
0V
CN708-8 nSSR HTC PCB +5V Heater Control Signal
CN765-5
0V
CN708-9 +5V HTC PCB +5V +5 VDC Power Supply
CN765-6
0V
CN709
Pin No. Signal Name Destination Signal Waveform Function
CN709-1 nPCHK1 Paper Level 1st Paper Tray Paper
Sensor-1 +5V Detection Signal
L: Detect
0V
217
Pin No. Signal Name Destination Signal Waveform Function
CN709-4 nUPLIMIT1 No Paper Paper Level Signal
Sensor-4 +5V (1st Feeder)
L: Detect
0V
CN710
Pin No. Signal Name Destination Signal Waveform Function
CN710-1 nCASETT Paper Tray Paper Tray Detection Signal
Sensor-1 +5V (1st Feeder)
L: Detect
0V
CN711
Pin No. Signal Name Destination Signal Waveform Function
CN711-1 nDUPSEN2 Duplex Sensor2-1 Duplex Unit Paper Detection
+5V Signal
L: Detect
0V
0V
218
Pin No. Signal Name Destination Signal Waveform Function
CN711-4 nDUPSEN3 Duplex Sensor3-1 Duplex Unit Paper Detection
+5V Signal
L: Detect
0V
0V
0V
CN712
Pin No. Signal Name Destination Signal Waveform Function
CN712-1 +5V SNS PCB-1 +5V +5 VDC Power Supply
0V
0V
219
Pin No. Signal Name Destination Signal Waveform Function
CN712-4 nB4SENS SNS PCB-4 Sheet Bypass Paper
+5V Detection Signal
0V
220
CN713
Pin No. Signal Name Destination Signal Waveform Function
CN713-1 +24VM HVPS +24V +24 VDC Power Supply
CN39-1
0V
0V
0V
0V
0V
CN714
Pin No. Signal Name Destination Signal Waveform Function
CN714-1 +24VM Printer Motor +24V +24 VDC Power Supply
2P-1
221
CN715
Pin No. Signal Name Destination Signal Waveform Function
CN715-1 +24VM Registration +24V +24 VDC Power Supply
Roller
Clutch-1
0V
CN716
Pin No. Signal Name Destination Signal Waveform Function
CN716-1 +5V Thermistor1-1 +5V +5 VDC Power Supply
0V
0V
0V
222
Pin No. Signal Name Destination Signal Waveform Function
CN716-6 GND Paper Exit Ground
Sensor-2
0V
CN717
Pin No. Signal Name Destination Signal Waveform Function
CN717-1 +24VDR Fan-1 +24V Fan Control Signal 24V/16V
+16V
0V
CN717-2 MGND Fan-3 Ground
0V
CN718
Pin No. Signal Name Destination Signal Waveform Function
CN718-1 +24VM EXFD PCB +24V +24 VDC Power Supply
CN790-1
0V
0V
0V
223
Pin No. Signal Name Destination Signal Waveform Function
CN718-6 pTRPMNB EXFD PCB Transport Unit Motor Signal
CN790-6 +5V
0V
0V
0V
0V
0V
0V
0V
0V
0V
0V
224
Pin No. Signal Name Destination Signal Waveform Function
CN718-17 +5V EXFD PCB +5V +5 VDC Power Supply
CN790-17
CN719
Pin No. Signal Name Destination Signal Waveform Function
CN719-1 n2WAYKEP1 Paper Stopper +5V Paper Stopper Solenoid
Solenoid-1 Signal
0V
0V
0V
0V
0V
225
Pin No. Signal Name Destination Signal Waveform Function
CN719-8 GND 2Way Sensor-2 Ground
0V
CN720
Refer to SC PC Board CN100.
CN721
Pin No. Signal Name Destination Signal Waveform Function
CN721-1 nCARTRIGE Waste Toner Waste Toner Box Detection
Sensor-1 +5V Signal
L: Detect
0V
CN723
Pin No. Signal Name Destination Signal Waveform Function
CN723-1 MGND DC Motor Ground
4P-1
0V
0V
0V
226
Pin No. Signal Name Destination Signal Waveform Function
CN723-4 nMMCK DC Motor +6V Printer Motor Clock
4P-4
0V
CN730
Pin No. Signal Name Destination Signal Waveform Function
CN730-1 GND IPC PCB Ground
J1-1
0V
0V
0V
0V
0V
0V
0V
0V
0V
227
Pin No. Signal Name Destination Signal Waveform Function
CN730-11 GND IPC PCB Ground
J1-11
0V
0V
0V
0V
0V
0V
0V
0V
228
Pin No. Signal Name Destination Signal Waveform Function
CN730-23 D[3] IPC PCB Data Signal
+5V
J1-23
0V
0V
0V
0V
0V
CN731
Pin No. Signal Name Destination Signal Waveform Function
CN731-1 +5V Option LVPS +5 VDC Power Supply
CN66-1 +5V
0V
229
CN732
Pin No. Signal Name Destination Signal Waveform Function
CN732-1 N.C. HTC PCB Not Used
CN768-1
0V
CN733
Pin No. Signal Name Destination Signal Waveform Function
CN733-1 +24VM OPC CLUTCH 1 +24V +24 VDC Power Supply
0V
230
3.13. ADF PC Board
CN21
Refer to SCN PC Board CN3.
CN22
Pin No. Signal Name Destination Signal Waveform Function
CN22-1 OUTA ADF Motor-1 +24V Motor Control Signal
0V
CN22-2 +24V ADF Motor-2 +24V +24 VDC Power Supply
0V
CN22-4 OUTB ADF Motor-4 +24V Motor Control Signal
0V
CN22-5 +24V ADF Motor-5 +24V +24 VDC Power Supply
0V
CN22-7 +24VOPF ADF Roller +24V +24 VDC Power Supply
Clutch-1
231
CN24
Pin No. Signal Name Destination Signal Waveform Function
CN24-1 +24VOPF Inverting Roller +24V +24 VDC Power Supply
Clutch-1
CN25
Pin No. Signal Name Destination Signal Waveform Function
CN25-1 +24VOPF Stamp Solenoid +24V +24 VDC Power Supply
ON 0V
CN26
Pin No. Signal Name Destination Signal Waveform Function
CN26-1 +24VOPF Release Lever +24V +24 VDC Power Supply
Plate Solenoid
232
CN27
Pin No. Signal Name Destination Signal Waveform Function
CN27-1 nAAPNT Original Detection Original Detection Signal
+5V
Sensor L: Detect
ON 0V
CN27-2 GND Original Detection Ground
Sensor
0V
CN28
Pin No. Signal Name Destination Signal Waveform Function
CN28-1 nAADL1 Original Length Original Length Detection
+5V
Sensor1 Signal
L: Detect
ON 0V
CN28-2 GND Original Length Ground
Sensor1
0V
233
Pin No. Signal Name Destination Signal Waveform Function
CN28-9 GND SNS PCB Ground
CN41-4
0V
CN29
Pin No. Signal Name Destination Signal Waveform Function
CN29-1 nAB1SN Read Point Read Point Detection Signal
Sensor +5V L: Detect
ON
0V
CN29-2 GND Read Point Ground
Sensor
0V
CN30
Pin No. Signal Name Destination Signal Waveform Function
CN30-1 nAEJC Eject Sensor Original Eject Detection
+5V
ON Signal
L: Detect
0V
0V
234
Pin No. Signal Name Destination Signal Waveform Function
CN30-4 nAB2SN Duplex Duplex Eject Detection
EjectSensor +5V Signal
L: Detect
ON
0V
CN30-5 GND Duplex Ground
EjectSensor
0V
235
3.14. EP PC Board
EP PCB
Enhanced Printing PCB
IC3
31
1
30 CN4
60
LED1
IC6
LED2
LED3
LED4
CN1
1 100
CN1
Refer to SC PC Board CN121.
236
3.15. CONS PC Board (For DP-3000 Only)
CN55
Pin No. Signal Name Destination Signal Waveform Function
CN106-9 AGND CONS PCB Ground
CN57-9
0V
CN56
Pin No. Signal Name Destination Signal Waveform Function
CN56-1 +5V CCD PCB +5V +5 VDC Power Supply
CN57-1
237
Pin No. Signal Name Destination Signal Waveform Function
CN56-4 PHYTG CCD PCB Transfer Gate Clock
CN57-4 +3.3V
0V
250 450mV
CN56-6 pPHYR CCD PCB Reset Gate Clock
CN57-6 250 450mV
250 450mV
CN56-8 pPHYCP CCD PCB Clamp Clock
CN57-8 250 450mV
250 450mV
250 450mV
CN57
Refer to SC PC Board CN106.
238
3.16. CCD PC Board
CN51 (For DP-2000/2500)
Refer to SC PC Board CN106.
CN51 (For DP-3000)
Refer to CONS PC Board CN55.
CN52
Pin No. Signal Name Destination Signal Waveform Function
CN52-1 FGND FG Ground
0V
239
3.17. FXB PC Board
CN160
Refer to SC PC Board CN122.
CN161
Pin No. Signal Name Destination Signal Waveform Function
CN161-1 (HOK2) LCU/LCE PCB Not Used
CN25-1
240
Pin No. Signal Name Destination Signal Waveform Function
CN161-12 AGND LCU/LCE PCB Ground
CN25-12
0V
241
3.18. PRIF PC Board
CN211
Refer to SC PC Board CN116.
CN212
Refer to SC PC Board CN115.
242
3.19. LCU/LCE PC Board
CN20
Pin No. Signal Name Destination Signal Waveform Function
CN20-3 L2(A) Telephone Line Line Signal
CN21
Pin No. Signal Name Destination Signal Waveform Function
CN21-3 T1 External Line Signal for the External
Telephone Telephone
CN23
Pin No. Signal Name Destination Signal Waveform Function
CN23-1 A1 SRU PCB Off Hook
Switch Hook Signal
+5V (H)
CN90-1
On Hook 0V (L)
CN25
Refer to FXB PC Board CN161.
Refer to G3B PC Board CN132.
243
3.20. SRU PC Board
CN90
Refer to LCU/LCE PC Board
CN91
Pin No. Signal Name Destination Signal Waveform Function
CN91-1 N.C. Not Used
0V
244
3.21. LSU PC Board
CN1
Refer to SC PC Board CN110.
CN2, CN3
Refer to LPC PC Board CN701.
245
3.22. SORT PC Board
CN150
Refer to SC PC Board CN120.
CN151
Refer to SC PC Board CN113.
246
3.23. HTC PC Board
CN760
Pin No. Signal Name Destination Signal Waveform Function
CN760-1 AC(L) AC Switch-2 AC Power Supply
AC100V
CN761
Pin No. Signal Name Destination Signal Waveform Function
CN761-1 AC(N) AC Switch-1 AC Power Supply
AC100V
247
CN764
Pin No. Signal Name Destination Signal Waveform Function
CN764-1 AC(L) Fuser Lamp AC Power Supply
AC100V
CN765
Refer to LPC PC Board CN708.
248
3.24. HTC2 PC Board
CN766
Pin No. Signal Name Destination Signal Waveform Function
CN766-1 AC(N) AC Switch-1 AC Power Supply
AC100V
CN767
Pin No. Signal Name Destination Signal Waveform Function
CN767-1 AC(N) Fuser Lamp AC Power Supply
AC100V
CN768
Refer to LPC PC Board CN732.
249
3.25. HCE PC Board (For 200V only)
CN80
Refer to HTC PC Board CN762.
CN81
Pin No. Signal Name Destination Signal Waveform Function
CN80-1 AC(L) LVPS AC Power Supply
CN60-1
AC100V
CN82
Pin No. Signal Name Destination Signal Waveform Function
CN81-1 AC(L) OPTION LVPS AC Power Supply
CN64-1
AC100V
250
3.26. HVPS
CN39
Refer to LPC PC Board CN713.
251
3.27. MAIN LVPS PC Board
CN60
Refer to HTC PC Board CN762.
CN61
Refer to SC PC Board CN101.
CN62
Refer to LPC PC Board CN702.Clean
252
3.28. Option LVPS PC Board
CN64
Refer to HTC PC Board CN763.
CN65
Refer to Finisher Unit.
CN66
Refer to LPC PC Board CN731.
253
3.29. ILS PC Board
CN750
Refer to LPC PC Board CN708.
254
3.30. EXFD PC Board
CN790
Refer to LPC PC Board CN718.
CN791
Pin No. Signal Name Destination Signal Waveform Function
CN791-1 nMMP0a Transport Motor Motor Drive Signal
+24V
0V
0V
0V
0V
CN792
Pin No. Signal Name Destination Signal Waveform Function
CN792-1 nKEEP1 Paper Stopper +24V Paper Stopper Solenoid
Solenoid-1 Signal
0V
CN792-2 +24VM Paper Stopper +24V +24 VDC Power Supply
Solenoid-2
0V
255
CN793
Pin No. Signal Name Destination Signal Waveform Function
CN793-1 nEXDF1 Paper Transport Paper Transport Unit Paper
Unit Sensor1-1 +5V Detection Signal
L: Detect
0V
CN794
Pin No. Signal Name Destination Signal Waveform Function
CN794-1 nEXDF3 Paper Transport Paper Transport Unit Paper
Unit Sensor3-1 +5V Detection Signal
L: Detect
0V
256
Pin No. Signal Name Destination Signal Waveform Function
CN794-6 LDEX4 Paper Transport Photo Sensor DC Drive
Unit Sensor4-3 +5V Voltage
0V
0V
257
3.31. INV PC Board
CN1
Refer to SCN PC Board CN9.
CN2
Pin No. Signal Name Destination Signal Waveform Function
CN2-1 HVAC1 LFB INV PC Board/Lamp Signal
CN181-1
258
3.32. IPC PC Board
J1
Refer to LPC PC Board CN730.
J2
Refer to Finisher Unit.
259
3.33. SDRM PC Board
CN1
Refer to SC PC Board CN107 and CN113.
Refer to SORT PC Board CN151.
260
3.34. SNS PC Board
CN41
Refer to ADF PC Board CN28.
261
3.35. Finisher Unit
Finisher Unit
Pin No. Signal Name Destination Signal Waveform Function
Finisher +24V OPTION LVPS +24V +24 VDC Power Supply
Unit 1 CN65-1
0V
Finisher GND IPC PCB Ground
Unit 3 J2-2
0V
0V
Finisher MGND OPTION LVPS Ground
Unit 5 CN65-2
0V
Finisher N.C.
Unit 8
Finisher N.C.
Unit 9
Finisher N.C.
Unit 11
Finisher N.C.
Unit 12
262
3.36. CST2 PC Board
CN770
Refer to LPC PC Board CN707.
CN771
Refer to LPC PC Board CN707.
CN772 (For DP-2000/2500)
Pin No. Signal Name Destination Signal Waveform Function
CN772-1 +24VM CST3 PCB +24V +24 VDC Power Supply
CN807-1
0V
0V
CN772-7 nOPCLK CST3 PCB +5V Paper Tray Command
CN807-7 Status Clock Signal
0V
CN772-8 nOPSTA CST3 PCB +5V Paper Tray Status Signal
CN807-8
0V
CN772-9 nOPSBSY CST3 PCB +5V Paper Tray Status Busy
CN807-9 Signal
H: Status Not Busy
0V L: Status Busy
263
Pin No. Signal Name Destination Signal Waveform Function
CN772-11 nOPFEDBSY CST3 PCB +5V Paper Tray Feed Clutch
CN807-11 Busy Signal
H: Command Not Busy
0V L: Command Busy
0V
0V
0V
CN772-7 nOPCLK CST3 PCB +5V Paper Tray Command
CN807-7 Status Clock Signal
0V
CN772-8 nOPSTA CST3 PCB +5V Paper Tray Status Signal
CN807-8
0V
CN772-9 nOPSBSY CST3 PCB +5V Paper Tray Status Busy
CN807-9 Signal
H: Status Not Busy
0V L: Status Busy
264
Pin No. Signal Name Destination Signal Waveform Function
CN772-10 nOPCBSY CST3 PCB +5V Paper Tray Command Busy
CN807-10 Signal
H: Command Not Busy
0V L: Command Busy
0V
CN772-13 nFDPCHK4 CST3 PCB 4th Paper Tray Paper
CN807-13 +5V Registration Detection
Signal
0V L: Detect
CN773
Pin No. Signal Name Destination Signal Waveform Function
CN773-1 +24VM Feed Roller +24V +24 VDC Power Supply
Clutch-1
CN773-2 nADF2 Feed Roller +24V 2nd Paper Tray Feed Roller
Clutch-2 Drive Signal
0V
CN773-3 +24VM Intermediate +24V +24 VDC Power Supply
Roller Clutch-1
0V
CN773-5 N.C.
265
CN774
Pin No. Signal Name Destination Signal Waveform Function
CN774-1 +24VM Lift DC Motor +24V +24 VDC Power Supply
CN774-2 nLIFTM2 Lift DC Motor +24V 2nd Paper Tray Lift Motor
Drive Signal
0V
CN775
Pin No. Signal Name Destination Signal Waveform Function
CN775-1 nPCHK2 NP Sensor-1 2nd Paper Tray Paper
+5V Detection Signal
L: Detect
0V
0V
0V
CN776
Pin No. Signal Name Destination Signal Waveform Function
CN776-1 nFDPCHK2 Registration 2nd Paper Tray Paper
Sensor-1 +5V Registration Detection
Signal
0V L: Detect
266
Pin No. Signal Name Destination Signal Waveform Function
CN776-3 LDFPCHK2 Registration Photo Sensor DC Drive
Sensor-3 Voltage
+1.5V
CN777
Pin No. Signal Name Destination Signal Waveform Function
CN777-1 nCST2 Paper Tray 2nd Paper Tray Detection
Sensor-1 +5V Signal
L: Detect
0V
CN778
Pin No. Signal Name Destination Signal Waveform Function
CN778-1 nJAMDOR Jam Access Cover 2nd Paper Tray Jam Access
Open Detection +5V Cover Open Detection
Sensor-1 Signal
0V L: Detect
267
3.37. CST3 PC Board
CN800
Pin No. Signal Name Destination Signal Waveform Function
CN800-1 nPCHK3 NP Sensor-1 3rd Paper Tray Paper
+5V Detection Signal
L: Detect
0V
CN800-2 GND NP Sensor-2 Ground
0V
CN801
Pin No. Signal Name Destination Signal Waveform Function
CN801-1 nCST3 Paper Tray 3rd Paper Tray Detection
Sensor-1 +5V Signal
L: Detect
0V
268
CN802
Pin No. Signal Name Destination Signal Waveform Function
CN802-1 nJAMDOR3 Jam Access Cover 3rd Paper Tray Jam Access
Open Detection +5V Cover Open Detection
Sensor-1 Signal
0V L: Detect
CN803
Pin No. Signal Name Destination Signal Waveform Function
CN803-1 pFDCHK3 Registration 3rd Paper Tray Registration
Sensor-1 +5V Signal
0V
CN804
Pin No. Signal Name Destination Signal Waveform Function
CN804-1 +24VM Lift DC Motor +24V +24 VDC Power Supply
CN804-2 nLIFTM3 Lift DC Motor +24V 3rd Paper Tray Lift Motor
Drive Signal
0V
CN805
Pin No. Signal Name Destination Signal Waveform Function
CN805-1 nMMP0a Motor +24V Motor Drive Signal
0V
269
Pin No. Signal Name Destination Signal Waveform Function
CN805-3 pMMP0a Motor +24V Motor Drive Signal
0V
0V
0V
CN806
Pin No. Signal Name Destination Signal Waveform Function
CN806-1 +24VM Feed Clutch-1 +24V +24 VDC Power Supply
CN806-2 nADF3 Feed Clutch-4 +24V 3rd Paper Tray Feed Roller
Drive Signal
0V
CN806-3 +24VM Intermediate +24V +24 VDC Power Supply
Roller Clutch-1
0V
CN806-5 N.C.
CN807
Refer to CST2 PC Board CN772.
CN808 (DP-2000/2500)
Pin No. Signal Name Destination Signal Waveform Function
CN808-1 +24VM CST2 PCB +24V +24 VDC Power Supply
CN770-3
270
Pin No. Signal Name Destination Signal Waveform Function
CN808-2 MGND CST2 PCB Ground
CN770-4
0V
271
Pin No. Signal Name Destination Signal Waveform Function
CN808-14 pMRCLH CST2 PCB 4th Paper Tray Intermediate
+5V
CN771-2 Roller Clutch Signal
H: Detect
0V
272
CN808 (DP-3000)
Pin No. Signal Name Destination Signal Waveform Function
CN808-1 +24VM CST2 PCB +24V +24 VDC Power Supply
CN770-3
273
Pin No. Signal Name Destination Signal Waveform Function
CN808-13 pADF CST2 PCB 4th Paper Tray Registration
+5V
CN771-1 Signal
0V
274
Pin No. Signal Name Destination Signal Waveform Function
CN808-25 N.C. CST2 PCB Not Used
CN770-15
275
3.38. G3B PC Board
CN131
Refer to SC PC Board CN123.
CN132
Pin No. Signal Name Destination Signal Waveform Function
CN132-1 (HOK2) LCU/LCE PCB Not Used
CN25-15
276
Pin No. Signal Name Destination Signal Waveform Function
CN132-12 GND LCU/LCE PCB Ground
CN25-12
0V
277
3.39. LANB PC Board
CN2
Refer to SC PC Board CN123.
CN5
Pin No. Signal Name Destination Signal Waveform Function
CN5-1 LINK LANC PCB +5V LANB PCB/ LANC PCB Link
CN200-1 Signal
0V
CN5-2 RXD LANC PCB +5V Reception Data Signal
CN200-2
0V
CN5-3 +5V LANC PCB +5V +5 VDC Power Supply
CN200-3
CN6
Pin No. Signal Name Destination Signal Waveform Function
CN6-1 RX- LANC PCB Reception Data "-" Signal
CN200-8
278
3.40. LANC PC Board
CN200
Refer to LANB PC Board CN5 and CN6.
279
4 Troubleshooting
4.1. Initial Troubleshooting Flowchart
START
280
4.2. Improper LCD Display
Start
YES
Is LED/LCD displayed? Does the display appear normal?
NO YES NO
END
END
281
4.3. Information Codes (INFO. CODES)
The 3-digit information codes display to show the unit’s status. These codes also print on the journal. The
following table indicates appropriate sections for troubleshooting.
Phase
Message
Transmission
Facsimile Communication Procedure
Facsimile Call
282
4.3.1. Information Codes: 400, 420
400 420
START START
Is transmission to the No
reference unit successful?
Yes 1. Replace the LCU/LCE
PCB.
2. Replace the FXB PCB.
3. Replace the SC PCB.
Yes
END END
283
4.3.2. Information Codes: 401, 402, 422
402, 422
START
401 END
START
END
284
4.3.3. Information Codes: 404, 405, 407
START
Is communication with No
reference unit successful?
Yes 1. Replace the LCU/LCE PCB.
2. Replace the FXB PCB
3. Replace the SC PCB.
END
285
4.3.4. Information Code: 416
START
No
Does the problem still occur?
Yes
No Yes
Does the problem still occur?
END
286
4.3.5. Information Codes: 408, 409, 417, 418, 490
START
Is communication with No
the reference unit
successful? 1. Replace the LCU/LCE PCB.
Yes 2. Replace the FXB PCB
3. Replace the SC PCB.
Is the unit transmitting or Transmitting
receiving?
No
Receiving Does the problem still occur?
Change Function
Change Function Parameter #010: Reduce Yes
Parameter #071: Increase Tx Attenuation Level
Error Tolerance Check the telephone line
condition.
Change Function
Parameter #018:Reduce
Rx Modem Speed
Change Function
Parameter #013: Increase
G3 Rx Equalization
END
287
4.3.6. Information Code: 434
START
END
288
4.3.7. Information Codes: 459, 494, 495
START
No
Does the problem still occur?
Yes
END
Does the trouble occur No
regardless of the remote unit?
Yes 1. Check the remote unit in
question.
(Remote unit is defective)
2. Refer to Sect. 4.6.
END
289
4.3.8. Information Codes: J00 - J91 (Except J70/J71) (Recording Paper Jam)
START
No
Is the recording paper size and
thickness within specification?
Yes Replace with correct paper.
No
Is the recording paper loaded
in the Paper Tray properly?
Yes Load the paper correctly.
No
Is the paper tray functional?
END
290
4.3.9. Information Code: N/A (No Recording Paper)
START
No
Is the Paper Tray seated
properly?
Yes Reseat the paper tray.
No
Is the recording paper
loaded in the paper tray?
Yes Load the paper.
No
Is the No Paper Actuator
operational?
Yes Replace the Actuator.
No
Is the NP Sensor
operational?
Yes Replace the NP Sensor.
No
Does the Paper Feed
Roller turn?
Overhaul the Clutch Gear
Yes Assembly.
END
291
4.3.10. Information Codes: J70, J71 (Document Jam)
START
Yes
Is the document path blocked?
No Remove the blockage.
No
Does the ADF Motor rotate?
Yes 1. Replace the ADF Motor.
2. Replace the ADF PCB.
No
Does the document feed into
the unit?
Yes Check all gears and rollers.
No
END Does the problem still occur?
Yes
292
4.3.11. Information Code: 630 (Dialing Error)
START
No
Is there a dial tone when
MONITOR button is
pressed? 1. Connect the telephone
line correctly.
Yes 2. Check the telephone line.
No
Is the remote machine busy?
Yes Can the unit dial the No
reference unit?
Yes 1. Check all connectors.
2. Replace the SC PCB.
Press the REDIAL button to
retry connection.
1. The remote machine is
defective.
2. Telephone line quality is
poor.
(Refer to Sect. 4.6.)
END END
293
4.3.12. Information Codes: 403, 411, 414, 415 (Polling Operator Trouble)
415 403,411,414
START START
END
294
4.4. Printed Copy Quality Problems
4.4.1. Black Copy
Paper Travel
START
No
Is the HVPS normal?
Yes 1. Check all connectors and voltages
on the HVPS.
2. Check the contacts between
HVPS and Toner Cartridge.
3. Replace the HVPS.
No
Is the LPC PCB normal?
Yes 1. Check all connectors and voltages
on the LPC PCB.
2. Replace the LPC PCB.
END
295
4.4.2. Blank Copy
Paper Travel
START
No
Is the HVPS normal?
Yes 1. Check all connectors and
voltages on the HVPS.
2. Check the Spring Connector
and voltage on the HVPS.
3. Replace the HVPS.
No
Is the LPC PCB normal?
Yes 1. Check all connectors and
voltages on the LPC PCB.
2. Replace the LPC PCB.
END
296
4.4.3. Vertical White Lines
Paper Travel
START
Yes
Is the recording paper damp?
No
Replace the recording paper.
END
297
4.4.4. Ghost Images
Paper Travel
AAA
A
START
No
Replace the recording paper.
No
Is the Process Unit operational?
Yes
Replace the Process Unit.
END
298
4.4.5. Vertical Dark Lines
Paper Travel
START
No
Is the LSU normal?
Yes
Replace the LSU.
END
299
4.4.6. Horizontal Dark Lines
Paper Travel
START
No
Is the LSU normal?
Yes Replace the LSU.
No
Is the HVPS normal?
END
300
4.4.7. Dark Background
Paper Travel
START
No
Replace the recording paper.
No
Is the LSU normal?
Yes
Replace the LSU.
No
Is the HVPS normal?
Yes 1. Check all connectors and
voltages on the HVPS.
2. Check the Spring Connector
and voltages on the HVPS.
3. Replace the HVPS.
END
301
4.4.8. Light Print
Paper Travel
START
Yes
Is the recording paper damp?
No
Replace the paper.
No
Is the Process Unit operational?
Yes
Replace the Toner Cartridge.
No
Is the HVPS normal?
Yes 1. Check all connectors and
voltages on the HVPS.
2. Replace the HVPS.
END
302
4.4.9. Horizontal White Lines
Paper Travel
START
No
Replace the recording paper.
No
Is the HVPS normal?
Yes 1. Check all connectors and
voltages on the HVPS.
2. Replace the HVPS.
END
303
4.4.10. Improper Fusing (Printed image does not bond to the paper)
P
START
Yes
Is the recording paper damp?
No
Replace the recording paper.
No
Is the Fuser Unit normal?
END
Note:
Replace the entire Fuser Unit when the Thermostat and / or the Thermistor turn into an open-circuit.
304
4.4.11. Voids in Solid Areas
Paper Travel
START
No
Replace the recording paper.
END
305
4.4.12. Black Dots
Paper Travel
START
END
306
4.4.13. Recording Paper Creases
Paper Travel
START
No
Replace the recording paper.
END
307
4.4.14. Poor Printed Copy Quality
START
No
Is the printed copy correct?
No
Is the received copy correct?
Yes 1. Check CN122 on the SC PCB.
2. Check CN161 on the FXB PCB.
3. Check CN25 on the LCU/LCE PCB.
3. Check the Telephone Line Cord.
4. Replace the SC PCB.
END
308
4.4.15. Document Skewing
START
Mo de
Copy le Is the Test Pattern printout NO Check the Scanner
Samp in Copier F1 Mode normal? mechanism.
YES
END
309
4.4.16. Abnormal Printing
START
Yes
Are there any foreign particles
or paper pieces in the receiver
unit? Remove the foreign particles or paper pieces
No from the receiver unit.
No
Do the rollers rotate properly?
END
310
4.4.17. Scanned Copy Quality Problems
START
Yes
Is the Xenon Lamp abnormal?
No
Replace the Xenon Lamp.
Yes
Is the scanning area dirty?
No 1. Clean the Scanning Glass (Sect. 2.2.6).
2. Clean Mirrors 1 and 2 (Sect. 2.2.6).
Yes
Is the Scanner Block abnormal?
No For DP-2000/2500
1. Check CN106 (SC PCB).
2. Check CN51 (CCD PCB).
3. Replace the CCD Assembly (207)
(Sect. 2.2.5).
4. Replace the SC PCB (Sect. 2.2.4).
For DP-3000
1. Check CN106 (SC PCB).
2. Check CN55,56 and 57 (CONS PCB).
3. Check CN51, CN52 (CCD PCB).
4. Replace the CCD Assembly (207)
(Sect. 2.2.5).
5. Replace the CONS PCB (Sect. 2.2.4)
5. Replace the SC PCB (Sect. 2.2.4).
END
311
4.4.18. Print Skew Adjustment for Platen Glass Scanning
Follow the procedures below to adjust for the skewing when scanning original(s) from the Platen Glass.
(A)
(B)
312
4.5. Document Feeder (ADF)
4.5.1. No Document Feed
START
NO END
Does the ADF Roller Replace the Clutch
rotate? or the ADF Motor. Replace the ADF
YES PCB, the SCN PCB
or the SC PCB.
NO
Is the trouble Replace the ADF PCB.
resolved?
YES
END
END
313
4.5.2. Document Jam
START
END
Note 1
Since 1/10th of the power is supplied during the Energy Saver Mode,
the output signal waveform at this pin is at 1/10th of the Duty Pulse.
314
4.5.3. Document Skew
START
315
4.6. Communications
This section explains general troubleshooting procedures for the 400 series of Information Codes. These
errors are primarily caused by poor telephone line quality (loss, noise, echo, etc.). This unit is furnished with
Service Mode 1 to assist in troubleshooting line quality problems.
It is suggested that both the transmitting unit and receiving unit be adjusted. This section gives relevant
parameters in Service Mode 1 for the transmitting and receiving sides. If no improvement is realized after
the parameters are adjusted, it is recommended that the parameters be returned to the default settings.
316
4.6.2. Poor Transmitted Copy Quality
START
Make a copy.
NO
Does CN9, pin 1 Replace the SCN
measure 0V when PCB.
the scan starts?
YES
Is CN181 on the NO
Xenon Lamp Connect it correctly.
connected properly?
YES
NO
Is the transmitted Check the connections of CN122 on the
copy normal? SC PCB, CN161 on the FXB PCB, and
YES CN25 on the LCU/LCE PCB.
Check the Telephone Line Cord.
Does poor transmitted Replace the LCU/LCE PCB and / or the SC PCB.
copy appear only NO
when transmitting to a Telephone line quality
specific receiver? is poor.
YES
END
317
4.6.3. Dialing Problems
START
Yes
Are you using direct dialing?
No
Check the dialed telephone number.
END
318
4.6.4. Transmission Problems
START
No
Does the ID display?
Yes 1. No ID function at the remote unit.
2. The ID is not set for the remote unit.
No
Is the copy quality OK?
Yes
Make a copy and refer to Sect. 4.4.17
Yes
Any other problems?
END
319
4.6.5. Reception Problems
START
No
Is the received copy OK?
Yes
Make a copy and refer to Sect. 4.4.14.
Yes
Any other problems?
No See Sect. 4.3 (Troubleshooting using
information codes).
END
320
4.6.6. Polling Problems
START
No
Is Polling reception OK?
Yes 1. Set the same polling password as the other party
is using.
2. Check the password of the remote unit.
No
Is Polling transmission OK?
Yes 1. Set the polling password or no - check mode.*
2. Check the password of the remote unit.
Yes
Any other problems?
No See Sect. 4.3
(Troubleshooting using information codes).
END
Note:
No-check Mode means that password is not set.
321
4.6.7. Recording Paper Jam
START
NO
Is the Pre-Feed Roller
operational? Clean or replace the Pre-Feed
YES Roller.
NO
Is the OPC Clutch rotation
normal? Check or replace the OPC
YES Clutch.
322
a
NO
Is the Lift DC Motor Unit normal?
YES Replace the Lift DC Motor Unit.
NO
Is the Solenoid for switching
paper path operational?
Replace the Solenoid.
YES
END
323
4.6.8. No Recording Paper
START
Is the NP Actuator NO
operational?
YES Replace the NP Actuator.
Is the NP Sensor NO
operational?
YES Replace the NP Sensor.
END
324
4.7. Error Codes (For Copier)
The self-diagnostic functions detect troubles in the important components of the copier.
When any trouble occurs, the copier stops.
4.7.1. User Error Code (U Code)
Note:
Uxx and a message will appear on the Panel Display.
325
Code Item Check Points
U20 CLOSE ADF COVER 1. ADF Cover is open.
2. ADF is not installed correctly.
3. ADF Cover Sensor is disconnected.
4. ADF Cover Sensor is defective.
5. LVPS connector is disconnected.
6. LVPS is defective.
U21 CLOSE PLATEN COVER Platen Cover is opened while scanning from ADF.
U22 CLOSE ADF EXIT COVER 1. ADF Exit Cover is open.
2. ADF is incorrectly installed.
3. ADF Exit Cover Sensor is disconnected.
4. ADF Exit Cover Sensor is defective.
5. LVPS connector is disconnected.
6. LVPS is defective.
U90 REPLACE BATTERY Backup Battery is wearing out.
326
4.7.2. Jam Error Codes (J Code)
B
C
A
327
Code Contents Section
J00 The Registration Sensor did not detect paper within a predetermined time after paper C
started feeding. (Sheet Bypass)
J01 The Registration Sensor did not detect paper within a predetermined time after the D
Paper Feed Roller started rotating. (1st Feeder Unit)
J02 The 2nd Registration Sensor does not detect paper within a predetermined time after D
the Paper Feed Roller started rotating. (2nd Feeder Unit)
J03 The 3rd Registration Sensor does not detect paper within a predetermined time after D
the Paper Feed Roller started rotating. (3rd Feeder Unit)
J04 The 4th Registration Sensor does not detect paper within a predetermined time after D
the Paper Feed Roller started rotating. (4th Feeder Unit)
J07 The Registration Sensor did not detect paper within a predetermined time after paper D
feed from 2nd Feeder Unit. (2/3/4 Feeder Unit)
J08 The Registration Sensor did not detect paper within a predetermined time after the D
Paper Feed Roller started rotating on the 3rd Feeder Unit. (3/4 Feeder Unit)
J09 The Registration Sensor did not detect paper within a predetermined time after the D
Paper Feed Roller started rotating on the 4th Feeder Unit. (4th Feeder Unit)
J12 The 2nd Registration Sensor did not detect paper within a predetermined time after D
the Paper Feed Roller started rotating.
J13 The 3rd Registration Sensor did not detect paper within a predetermined time after D
the Paper Feed Roller started rotating.
J14 The 4th Registration Sensor did not detect paper within a predetermined time after D
the Paper Feed Roller started rotating.
J22 The 2nd Registration Sensor detect paper at the time of the initials. D
J23 The 3rd Registration Sensor detect paper at the time of the initials. D
J24 The 4th Registration Sensor detect paper at the time of the initials. D
J30 The Registration Sensor did not detect no paper within a predetermined time. C
J33 The Registration Sensor detect paper at the time of the initials. C, D
J34 The Registration Sensor did not detect paper within a predetermined time after C
Sensor 4 of Automatic Duplex Unit is ON.
J40 The eject paper Sensor does not detect paper within a predetermined time after C
Registration Sensor is ON.
J41 The eject paper Sensor does not detect no paper within a predetermined time after C
eject paper Sensor is ON.
J42 The Paper Exit Sensor detects paper when machine is standby. C
J45 The Paper Exit Sensor of dual-path exit guide unit does not detect paper within a C
predetermined time after Registration Sensor is ON.
J46 The Paper Exit Sensor of dual-path exit guide unit is not OFF within a predetermined C
time.
J47 The Paper Exit Sensor of dual-path exit guide unit detects paper when machine is C
standby.
J50 The Paper Transport Unit Sensor 1 does not detect paper within a predetermined time C
after eject paper Sensor of dual-path exit guide unit is ON.
J51 The Paper Transport Unit Sensor 2 does not detect paper within a predetermined time B
after eject paper Sensor of dual-path exit guide unit is ON.
J52 The Paper Transport Unit Sensor 3 does not detect paper within a predetermined time B
after eject paper Sensor of dual-path exit guide unit is ON.
J53 The Paper Transport Unit Sensor 4 does not detect paper within a predetermined time B
after eject paper Sensor of dual-path exit guide unit is ON.
J55 The Paper Transport Unit Sensor 1 is not OFF within a predetermined time. B
328
Code Contents Section
J56 The Paper Transport Unit Sensor 2 is not OFF within a predetermined time. B
J57 The Paper Transport Unit Sensor 3 is not OFF within a predetermined time. B
J58 The Paper Transport Unit Sensor 4 is not OFF within a predetermined time. B
J59 The Paper Transport Unit Sensor detects paper when machine is standby. B
J60 The Finisher Registration Sensor did not detect paper within a predetermined time A
after eject paper Sensor is ON.
J61 The stapler is not activated correctly. A
J62 The Finisher Registration Sensor detects no paper within a predetermined time after A
Finisher Registration Sensor is ON.
J63 The Finisher Registration Sensor detects paper when machine is standby. A
J64 The Finisher is disconnected during printing. A
J65 Paper multi-feed. A
J66 Finisher Aligning Guide is not activated correctly. A
J67 Finisher Return Roller is not activated correctly. A
J70 Read Point Sensor does not go ON within 10 seconds after the original starts feeding. E
(Information Code 030 is printed on the Transaction Journal instead.)
J71 Original was longer than 78.7 in (2m). E
(Information Code 031 or 032 is printed on the Transaction Journal instead.)
J80 The Automatic Duplex Unit Sensor 1 does not detect paper within a predetermined B
time.
J81 The Automatic Duplex Unit Sensor 2 does not detect paper within a predetermined C
time after Automatic Duplex Unit Sensor 1 is ON.
J82 The Automatic Duplex Unit Sensor 3 does not detect paper within a predetermined C
time after Automatic Duplex Unit Sensor 2 is ON.
J83 The Automatic Duplex Unit Sensor 4 does not detect paper within a predetermined C
time after Automatic Duplex Unit Sensor 3 is ON.
J84 The Automatic Duplex Unit Sensor 1 detects no paper within a predetermined time C
after Automatic Duplex Unit Sensor 1 is ON.
J85 The Automatic Duplex Unit Sensor 2 detects no paper within a predetermined time C
after Automatic Duplex Unit Sensor 2 is ON.
J86 The Automatic Duplex Unit Sensor 3 detects no paper within a predetermined time C
after Automatic Duplex Unit Sensor 3 is ON.
J87 The Automatic Duplex Unit Sensor 4 detects no paper within a predetermined time C
after Automatic Duplex Unit Sensor 4 is ON.
J88 The Automatic Duplex Unit Sensor 1 detects paper when machine is standby. C
J89 The Automatic Duplex Unit Sensor 2, 3 or 4 detects paper when machine is standby. C
J90 A PRINT signal is not received within 1 minute after the FEED signal is received. -
J91 A Paper Tray is pulled out when feeding a paper. -
329
4.7.3. Mechanical Error Codes (E Code)
• E1: Optical Unit Error
330
E1: Optical Unit Error
331
Code Function Check Points
E5- 12 Main CPU/LPC Interface Error 1. SC/LPC PCB connector is disconnected.
2. SC/LPC PCB is defective.
E5- 13 LPC System Error 1. SC/LPC PCB connector is disconnected.
2. SC/LPC PCB is defective.
E5- 14 Option Installation Error 1. SC/LPC PCB connector is disconnected.
2. SC/LPC PCB is defective.
E5- 15 Key Counter Not Installed 1. SC/LPC PCB connector is disconnected.
2. SC/LPC PCB is defective.
E5- 22 Finisher communication 1. SC/LPC PCB connector is disconnected.
2. SC/LPC PCB is defective.
E7: Optional Unit Error
332
Code Function Check Points
E7- 28 Finisher Bundling Process 1. Motor connector is disconnected.
Motor 2. Motor is defective.
3. LVPS connector (CN65/66) is disconnected.
4. LVPS is defective.
5. IPC PCB connector is disconnected.
6. LPC PCB connector (CN731) is disconnected.
7. LPC/IPC PCB is defective.
E13: Out of Toner
333
4.8. Information Codes Table (For Facsimile)
Information Codes
Code Mode Phase Description of Problem Cause
200 RCV C Decoding process is not completed Defective SC PCB.
at the end of phase C.
212 XMT A-E Interface error occurred between Modem is defective. (SC PCB)
RCV the CPU and modem. Software problem occurred. (SC PCB)
301 XMT System fault. Software problem occurred. (SC PCB)
RCV
331 XMT C 8-minutes timer error.
(Germany only)
360 - - Incomplete initialization for EP EP PC Board incorrectly installed on the
PCB. SC PC Board.
FRM PC Board incorrectly installed on
the EP PC Board.
Defective EP PC Board.
Defective FRM PC Board.
Defective SC PC Board.
361 - - DPRAM (Dual Port RAM) EP PC Board incorrectly installed on the
initialization error on EP PCB. SC PC Board.
FRM PC Board incorrectly installed on
the EP PC Board.
Flash ROM on the FRM PC Board is
blank.
Defective EP PC Board.
Defective FRM PC Board.
Defective SC PC Board.
362 - - Command Sequence Error. Software problem occurred. (SC/FRM
PCB)
400 XMT B T1 timer (35±5 sec) elapsed Wrong number is dialed and the START
without detecting 300 bps signal. button is pushed.
Telephone line is disconnected while
dialing.
SC PCB (Modem) or LCU/LCE PCB is
defective.
Receiver is defective. (It may only be
transmitting CED)
401 XMT B DCN was returned from receiver Your machine's ID Number is not
while transmitter is waiting for CFR programmed.
or FTT. Possible incompatibility or incorrect
Password (Password Reception,
Selective Receive).
Mailbox is full.
402 XMT B DCN was returned from receiver Receiver working in non-CCITT mode
while transmitter is waiting for only. (Possible incompatibility)
NSF/DIS.
403 RCV B Transmitter had no polling function. "POLLED=ON" (polling XMT ready) is
(Polling) not set at the transmitter.
Document to be transmitted is not
placed at the transmitter.
334
Information Codes
Code Mode Phase Description of Problem Cause
404 XMT B Transmitter sent NSS (or DCS) Receiver is defective. (Modem, LCU/
followed by TCF three times, but LCE PCB, etc.)
the receiver did not respond. (CFR SC PCB or LCU/LCE PCB is defective.
or FTT is usually returned) Receiver disconnects line during first
NSS (or DCS) is transmitted.
405 XMT B Transmitter received FTT after it Line quality is poor. (TCF is damaged
transmitted TCF at 2400bps. due to line noise)
Received RTN after Receiver is defective. (Modem, LCU/
communicating at 2400 bps. LCE PCB, etc.)
SC PCB or LCU/LCE PCB is defective.
406 RCV B XMT-Password mismatched. RCV- XMT, RCV password does not match.
(Password Password mismatched. Selective Last 4 digits of TSI does not match with
Comm.) RCV incomplete. the last 4 digits of Auto Dial telephone
number.
407 XMT D Transmitter received no response Receiver is defective. (No paper, paper
after it transmitted post message, jamming, etc.)
such as EOP, MPS, EOM, etc...or Receiver ceased receiving because of
received DCN. excessive error. (Line quality is poor)
SC PCB (Modem) or LCU/LCE PCB is
defective.
408 XMT D Transmitter received RTN after it Receiver receives data with error. (Line
transmitted EOP, MPS, or EOM. quality is poor)
Receiver is defective. (Modem, LCU/
LCE, etc.)
SC PCB or LCU/LCE PCB are
defective.
409 XMT D Transmitter receives PIN after it Receiver receives data with error due to
transmitted a post message, such poor line quality, and receiving operator
as EOP, MPS, EOM, etc. requests voice contact.
Receiver is defective. (Modem, LCU/
LCE, etc.)
SC PCB or LCU/LCE PCB are
defective.
410 RCV D Received DCN while waiting for Interface or line is faulty.
post command. (EOP, MPS, EOM, Transmitter is defective.
etc.)
411 RCV B Received DCN after transmitting Transmitter is not ready for polling
(Polling) NSC. communication.
Password does not match between
transmitter and receiver.
412 G3 RX B, D No response within 12 seconds in Transmitter is defective.
NSS/DCS/MPS wait state. (After SC PCB is defective.
transmitting FTT)
414 RCV B No response received after Password does not match between
(Polling) transmitting 3rd NSC. transmitter and receiver.
Transmitter is defective. (No original,
document jam, etc.)
415 XMT B Remote side attempted to receive Inform the remote side that your
(Polling) message from your machine in machine does not have the polling
polling communication. transmission feature.
335
Information Codes
Code Mode Phase Description of Problem Cause
416 RCV D Receiver did not detect post Transmitter is defective.
command, such as EOP, MPS, Line quality is poor. (RTC signal is
EOM, etc. distorted due to line noise)
SC PCB or LCU/LCE PCB are
defective.
417 RCV C Receiver returned RTN in Line quality is poor. (There are
response to post message. excessive errors in received data)
SC PCB or LCU/LCE PCB are
defective.
418 RCV C Receiver transmitted PIN in Line quality is poor. (There are
response to PRI-Q from excessive errors in received data)
transmitter. (Transmitting operator SC PCB or LCU/LCE PCB are
requests voice contact) defective.
420 RCV B T1 timer (35 sec.) elapsed without There is wrong incoming call.(non-
detecting 300 bps signal. facsimile communication)
Transmitter is defective.
SC PCB or LCU/LCE PCB is defective.
421 RCV B Busy Tone is detected after Remote station disconnected the line.
sending NSF Signal. Wrong number is dialed.
422 XMT B Content of NSF (or DIS) or NSC There is an incompatibility.
(or DTC) was invalid.
427 G3 B DCN received to NSF/CSI/DIS The interface is incompatible.
RCV transmitted.
433 XMT B, D T.30 Protocol abnormal. Defective remote station.
RCV
434 XMT or RCV B CD (response from Modem) did Remote unit is defective.
not turn OFF within 180 sec. after SC PCB or LCU/LCE PCB is defective.
receiver detected FLAG signal.
436 G3 RX C DCN received after transmitting Transmitter is defective or incompatible.
FTT. Line quality is poor.
456 RCV B Received relay transfer request or
confidential document to distribute
to an end receiving station or all
confidential mailboxes are used.
457 RELAY XMT B Remote unit does not have
CONF. XMT/ Relayed XMT or Confidential
POLL Comm. capability.
459 RCV C Failed training in Phase C. Line quality is poor. (Training signal is
distorted due to line noise)
SC PCB or LCU/LCE PCB are
defective.
490 RCV C Sum of error lines exceeded the Line quality is poor.
limit (Function Parameter No. 70) SC PCB or LCU/LCE PCB are
of 64 lines. defective.
494 RCV C Interval between two EOLs was Transmitter is defective.
more than 10 sec. when receiver Line quality is poor. (EOL is damaged
received message data. due to line noise)
SC PCB or LCU/LCE PCB are
defective.
336
Information Codes
Code Mode Phase Description of Problem Cause
495 XMT C During reception, CD turned OFF Line is disconnected.
RCV or continued ON for long time. Transmitter is defective.
During communication, lost loop - SC PCB or LCU/LCE PCB are
current. defective.
496 XMT C CS of modem is not able to turn SC PCB is defective.
ON.
501 XMT/ B Remote unit does not have
RCV(V.34) compatible Modem.
502 XMT/ B, C, D During reception, CD turned OFF Line is disconnected.
RCV(V.34) or continued ON for long time. Transmitter is defective.
During communication, lost loop - SC PCB or LCU/LCE PCB are
current. defective.
503 XMT/ B, C, D CS of modem is not able to turn SC PCB is defective.
RCV(V.34) ON during training. Line is disconnected.
504 RCV/V.34 B Polling is rejected from the remote No polling original is set.
(Polling) station.
505 XMT/V.34 B Polling XMT is rejected. No polling original is set.
(Polling)
540 XMT ECM B No response after transmitting 3rd Incompatible interface.
CTC or DCN received.
541 XMT ECM D No response after transmitting 3rd Line is faulty.
EOR or received DCN. LCU/LCE PCB abnormal.
542 XMT ECM D No response to the 3rd RR Remote unit is abnormal.
transmitted or received DCN.
543 XMT ECM D T5 timer (60 sec.) elapsed without Remote unit is abnormal.
MCF.
544 XMT ECM D Stopped Transmission after EOR Line is faulty.
Transmission. LCU/LCE PCB abnormal.
550 RCV ECM C Timer between frames in phase C Defective remote station.
has elapsed.
554 RCV ECM D Transmitted ERR after receiving Faulty line.
EOR.
555 RCV ECM D Transmitted PIN after receiving Faulty line and Operator Call requested
EOR. by RX side.
570 RCV B Password or machine code did not
match during remote diagnostic
communication.
571 XMT B Remote unit did not have the
remote diagnostic function.
580 XMT B Sub-address transmission to a unit Sub-address transmission to a unit that
that has their DIS bit 49 (NSF bit has no Sub-address function.
155) OFF.
581 XMT B Sub-address Password Sub-address transmission to a unit that
transmission to a unit that has their has no Sub-address function.
DIS bit 50 (NSF bit 156) OFF.
601 XMT ADF Door was opened during ADF
transmission.
623 XMT A No original was in the ADF. (Built- Operator removed the original from the
in dialer engaged) ADF after dialing was completed.
Original was not set properly in the ADF.
337
Information Codes
Code Mode Phase Description of Problem Cause
630 XMT or RCV B Redial count over. No dial tone detected. Sensor dial tone
(Polling) is not detected. (country dependent)
Busy tone is detected. (country
dependent) T1 timer (35±5 sec) elapsed
without a signal from the receiver.
631 XMT A "STOP" button was pressed during
Auto Dialing.
634 XMT Redial count over with no response
or busy tone was not detected.
Note:
U.S.A. and Canadian models
will redial only once if a busy
tone is not detected.
638 XMT Power turned off with applicable Power switched off. Power failure
data in memory or during occurred.
communication.
710 XMT LAN Command Response between Defective LANC/LANB PCB.
RCV LANC/LANB PCB timed out.
712 XMT LAN Unknown email address replied Mail Server received an incorrect email
from the Mail Server. address. (Dependent on Server's Mail
application)
713 XMT LAN Memory overflow in the LAN The document data exceeded 1.6
Interface. Mbyte/page and cannot be sent.
714 XMT LAN LAN Interface error. The 10Base-T cable is not connected.
RCV Cannot logon to the LAN. An unexpected LAN problem occurred.
Check the LANC/LANB PCB connector.
715 XMT LAN TCP/IP connection timed out. Incorrect IP Address is set.
Verify the IP Address, Default Router IP
Address, SMTP Server IP Address.
716 XMT LAN Cannot logon to the LAN. Incorrect SMTP Server IP Address is
set.
No email application is activated on the
Mail Server.
717 XMT LAN Incomplete SMTP Protocol Mail Server’s hard disk may be full.
transmission. Mail Server is defective.
718 XMT LAN Page Memory Overflow occurred Check the document size and
while receiving printing data. The resolution.
paper size selected within your Ask originator to re-send in a supported
application to print is larger than size and resolution.
the paper size loaded in the
cassette(s).
719 RCV LAN Received data via LAN is in a Ask the originator to re-send with a
format that is not supported. supported file attachment:
* In a TIFF-F format.
* Image data conforming to A4/Letter
size.
720 POP LAN Unable to connect with the POP Incorrect POP Server address is set.
Server. POP Server is down.
721 POP LAN Unable to login to the POP Server. Incorrect User Name or Password is set.
725 XMT LAN DNS Server connection timed out. Incorrect DNS Server address is set.
POP DNS Server is down.
338
Information Codes
Code Mode Phase Description of Problem Cause
726 XMT LAN Received an error response from Incorrect POP Server address is set.
POP the DNS Server. Incorrect SMTP Server address is set.
730 RCV LAN Unable to program the Internet Verify that the Fax Parameter #158 is
parameters or the autodialer with set to 2: Valid.
Email from a PC.
731 RCV LAN Dialer full while Relayed Dial buffer for manual number dialing
Transmission Request was (70 stations) are being used.
received.
741 XMT, Polling Unable to dial Deleted the registered station name
before dialing with Timer Controlled
Communications, etc.
800 Relay The machine was requested to
Comm. relay a document but has no Relay
Hub capability.
814 Conf. XMT The remote station does not have
Conf. Polling Relay XMT nor Confidential
Relay Communication capability.
Comm.
815 Conf. RCV Mailbox is full.
816 Conf. Polled The received Polling Password did
not match.
825 Conf. RCV Parameter settings of the remote
Conf. Polled station are not properly set.
870 MEM XMT Memory overflow occurred while
Multi-Copy storing documents into memory.
339
4.9. Diagnostic Codes (For Facsimile)
The 13-digit Diagnostic Code is provided for the service engineer to analyze how the communication was
performed. The code is recorded on the Journal.
Journal Example
NO. COMM. PAGES FILE DURATION X/R IDENTIFICATION DATE TIME DIAGNOSTIC
01 OK 001 129 00:00'42 XMT 123 456 789 NOV-15 01:55 C8649003C0000
Definition
Data Manufacturer
Code
0 -
1 Casio
2 Canon
3 Sanyo
4 Sharp
5 Tamura
6 Toshiba
7 NEC
8 Oki
9 Hitachi
A Xerox
B Fujitsu
C Matsushita
D Mitsubishi
E Murata
F Ricoh
340
2nd Digit
-: Not used/defined
Definition
Data
ID (TSI, CSI, CIG) RTN DCN STOP Button
0 - - - -
1 Received - - -
2 - Received - -
3 Received Received - -
4 - - Received -
5 Received - Received -
6 - Received Received -
7 Received Received Received -
8 - - - Pressed
9 Received - - Pressed
A - Received - Pressed
B Received Received - Pressed
C - - Received Pressed
D Received - Received Pressed
E - Received Received Pressed
F Received Received Received Pressed
3rd Digit
-: Not used/defined
Definition
Data
Resolution (dpi) Paper Width
0 - A4
1 S-Fine A4
2 400 x 400 A4
3 300 x 300 A4
4 - B4
5 S-Fine B4
6 400 x 400 B4
7 300 x 300 B4
8 - -
9 - -
A - -
B - -
C - A3
D S-Fine A3
E 400 x 400 A3
F 300 x 300 A3
341
4th Digit
-: Not used/defined
Definition
Data
Scanning Rate Resolution
0 20 ms/line Std
1 5 ms/line Std
2 10 ms/line Std
3 - Std
4 40 ms/line Std
5 - Std
6 - Std
7 0 ms/line Std
8 20 ms/line Fine
9 5 ms/line Fine
A 10 ms/line Fine
B - Fine
C 40 ms/line Fine
D - Fine
E - Fine
F 0 ms/line Fine
5th Digit
-: Not used/defined
Definition
Data Memory/
Deferred Comm. Dialing/RCV
Non-Memory
0 - Manual Non-Memory
Communication
1 Used Manual Non-Memory
Communication
2 - Auto Dialing Non-Memory
3 Used Auto Dialing Non-Memory
4 - Auto RCV Non-Memory
5 Used Auto RCV Non-Memory
6 - Remote RCV Non-Memory
7 Used Remote RCV Non-Memory
8 - Manual Memory
Communication
9 Used Manual Memory
Communication
A - Auto Dialing Memory
B Used Auto Dialing Memory
C - Auto RCV Memory
D Used Auto RCV Memory
E - Remote RCV Memory
F Used Remote RCV Memory
342
6th Digit
-: Not used/defined
Definition
Data Password
Polling XMT/RCV Selective Comm.
Comm.
0 - RCV Off Off
1 Yes RCV Off Off
2 - XMT Off Off
3 Yes XMT Off Off
4 - RCV On Off
5 Yes RCV On Off
6 - XMT On Off
7 Yes XMT On Off
8 - RCV Off On
9 Yes RCV Off On
A - XMT Off On
B Yes XMT Off On
C - RCV On On
D Yes RCV On On
E - XMT On On
F Yes XMT On On
7th Digit
-: Not used/defined
Definition
Data Sub-Address Confidential Turnaround
Relayed Comm.
Comm. Comm. Polling
0 - - - -
1 Yes - - -
2 - Yes - -
3 Yes Yes - -
4 - - Yes -
5 Yes - Yes -
6 - Yes Yes -
7 Yes Yes Yes -
8 - - - Yes
9 Yes - - Yes
A - Yes - Yes
B Yes Yes - Yes
C - - Yes Yes
D Yes - Yes Yes
E - Yes Yes Yes
F Yes Yes Yes Yes
343
8th Digit
-: Not used/defined
Definition
Data Advanced Cover Sheet
Comm. XMT
0 - -
1 Report XMT -
2 Check & Call -
3 - -
4 Memory Transfer -
5 - -
6 - -
7 - -
8 - Yes
9 Report XMT Yes
A Check & Call Yes
B - Yes
C Memory Transfer Yes
D - Yes
E - Yes
F - Yes
9th Digit
-: Not used/defined
Definition
Data Standard/ Non-
Short Protocol
Standard
0 - Standard
1 - Standard
2 - Standard
3 - Standard
4 - Standard
5 - Standard
6 - Standard
7 - Standard
8 - Non-Standard
9 B Non-Standard
A - Non-Standard
B D Non-Standard
C - Non-Standard
D B Non-Standard
E - Non-Standard
F D Non-Standard
344
10th Digit
-: Not used/defined
Definition
Data
Coding ECM
0 MH -
1 MR -
2 MMR -
3 JBIG -
4 - -
5 - -
6 - -
7 - -
8 MH Yes
9 MR Yes
A MMR Yes
B JBIG Yes
C - Yes
D - Yes
E - Yes
F - Yes
11th Digit
-: Not used/defined
Definition
Data Symbol Rate
V.34
(V.34)
0 - -
1 - -
2 - -
3 - -
4 - -
5 - -
6 - -
7 - -
8 2400 sr Yes
9 - Yes
A 2800 sr Yes
B 3000 sr Yes
C 3200 sr Yes
D 3429 sr Yes
E - Yes
F - Yes
345
12th Digit
-: Not used/defined
Definition
Data Modem Speed
Modem Speed
(V.34)
0 2400 bps -
1 4800 bps 2400 bps
2 7200 bps 4800 bps
3 9600 bps 7200 bps
4 TC 7200 bps 9600 bps
5 TC 9600 bps 12000 bps
6 12000 bps 14400 bps
7 14400 bps 16800 bps
8 - 19200 bps
9 - 21600 bps
A - 24000 bps
B - 26400 bps
C - 28800 bps
D - 31200 bps
E - 33600 bps
F - -
13th Digit
-: Not used/defined
Definition
Data
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
346
4.10. Troubleshooting (For PCL 6 Emulation Kit)
4.10.1. Checking the Basics
This section explains how to solve problems including error messages or unexpected printing results.
If the Panafax Printing System is not printing or working as expected, and if you are not sure
what to do, start your troubleshooting by checking the basics below:
347
4.10.3. Error Message appears on the PC
Error Message Solutions
Network Print DLL Error. • Check if the Panafax facsimile unit is turned "On" and the 10Base-T cable
is properly connected.
• Printer Properties may be incorrectly configured. (i.e. Printer Port)
Network Port is Busy. • The Panafax facsimile unit may be processing someone’s print job,
please wait and try again later.
• The Panafax facsimile unit is either Transmitting or Receiving an email.
Cannot print because an error is • Verify and specify the paper size or orientation to coincide with the
found in the current printer application and the printer driver settings.
setting.
If Information Codes 360, 361 or • Contact your local Panasonic Authorized Dealer.
362 are displayed on the LCD.
4.10.5. System Error (Floppy disk drive related error during installation)
Problem Solutions
Specified an incorrect drive. • Specify the correct Floppy disk drive.
• Make sure the Floppy disk is inserted properly.
Drive not ready. • Insert the Floppy disk into the drive and click “Retry”.
There was a problem with either • Make sure the Floppy disk is inserted properly.
the Floppy disk or the Floppy • Try a different Floppy disk.
disk drive. • Try the Floppy disk in a different PC.
348
5 Service Modes
5.1. Service Modes (For Copier)
These service modes are provided to assist the technician in checking for abnormalities in the copier and a
means of making adjustments to the Input/Output of major components.
5.1.1. Service Mode Procedure
For DP-2000
Service
Item Function
mode
F1 Self Test 00 CCD Test This test is used for checking the CCD.
01 LCD/LED Test This test is used for checking the LCD
and LEDs.
02 Page Memory Test This test is used for checking the Page
Memory.
03 Print Test Pattern 1 Prints the pattern for setting the Paper
position alignment.
04 Print Test Pattern 2 Factory use only.
05 PRT PWM Adj. Pattern Prints the gray steps when the Start key is
pressed. (Factory use only)
F2 Single Copy Test One sheet is copied when the Start key is
pressed.
F3 Continuous Copy Test Multi copies are made when the Start key
is pressed.
F4 Input / Output Status Test The functioning of Input / Output items
(selected item numbers) is checked.
F5 Function Parameters Various function settings (selected by
code numbers) can be changed.
F6 Adjustment Parameters Various function settings (selected by
code numbers) can be adjusted.
349
Service
Item Function
mode
F7 Electronic 00 Not Used
Counter 01 Key Operator ID Key Operator’s identification code for
access to the counter mode.
Maintenance 02 Total Count Total count for all copies / prints.
Count 03 PM Count Preventive Maintenance count.
04 Scanner PM Count PM count for scanner read.
05 ADF/iADF PM PM count for originals fed.
Count
06 OPC Drum Count PM count for OPC Drum paper fed.
07 Process Unit Count PM count for Process Unit paper fed.
08 Paper Transport PM count for Paper Transport Unit paper
Count (See Note) fed.
09 ADU Count PM count for Automatic Duplex Unit
(See Note) paper fed.
10 Dual-Path Count PM count for Dual-Path Exit Guide Unit
(See Note) paper fed.
Paper Feed 11 Sheet Bypass Total count of paper fed from the sheet
Count Count bypass.
12 1st Paper Tray Total count of paper fed from the 1st
Count paper tray.
13 2nd Paper Tray Total count of paper fed from the 2nd
Count paper tray.
14 3rd Paper Tray Total count of paper fed from the 3rd
Count paper tray.
15 4th Paper Tray Total count of paper fed from the 4th
Count paper tray.
Scanner Count 16 ADF/iADF Count Total count of originals fed through the
ADF/iADF.
17 ADF/iADF Read Total count of originals scanned through
Count the ADF/iADF.
18 Scanner Count Total count of scanning operations.
19 Scanner Read Total count of scanner read.
Count
Copy Count 20 Copy Print Count Total count of copies printed.
21 Copy Scan Count Total count of copies scanned.
PC Count 22 PC Print Count Total count printed from PC.
23 PC Scan Count Total count scanned from PC.
Fax Count 24 Fax Transmit Count Total count of Fax transmitted.
25 Fax Receive Count Total count of Fax received.
26 Fax Print Count Total count of Fax printed.
99 Clear All Counts All counters are cleared.
350
Service
Item Function
mode
F8 Service Adjustment Perform pseudo-operation of an item
(selected by code numbers)
00 CHK Mirror Movement When replacing the exposure lamp.
Procedure:
a) Press the Start key to move the
exposure lamp to the position (approx.
250mm from the optics home position)
where it can be replaced.
b) To return the optical system to the
home position, press the CLEAR key.*
06 Error Log Print/View a) Each time the arrow key is pressed,
the machine errors or paper jam codes
stored in memory are displayed,
beginning with the oldest code.
Note:
Only the 30 most recent codes are
displayed.
07 Error Log Clear a) Press the Reset key.
A Message "Error code can be cleared
with the Start key" is displayed on the
LCD.*
b) Press the Start key.
12 Orginal Size Sensor Adjust the slice level for the original size
detection sensors automatically. Execute
this mode by closing the platen cover.
19 Move Mirror To Lock a) Press the Start key then the mirror unit
moves to locked position for
transporting the copier.
b) When the mirror unit is locked, any
digit key input is not be accepted.
Note:
The lock operation is automatically
reset when the Power switch is turned
ON again.
47 ADF Continuous Test Press START key to start.
48 Platen Continuous Test Press START key to start.
351
Service
Item Function
mode
F9 Unit 00 Fax Function Parameters
Maintenance 01 Service Alert Tel # Displays the contact number when a
machine malfunction occurs.
02 Firmware 00 Host Displays the firmware version for host.
Version 02 Scanner Displays the firmware version for scanner.
03 Printer Displays the firmware version for printer.
04 Finisher Displays the firmware version for finisher.
05 Printer Board (PDL) Displays the firmware version for PDL.
06 LAN Board Displays the firmware version for LAN.
07 G3B Board Displays the firmware version for G3B
Board.
08 Modem Displays the firmware version for modem.
09 3rd Paper Feed Displays the firmware version for 3rd
Module Paper Feed Module.
03 Print Device 00 F5/F6 Parameters Prints the memory contents of the F5 and
Info. F6 modes.
01 Printer Report Prints the printer report.
02 Counter Information Prints the counter information.
03 System Addr. Info. Prints the system memory setting.
04 RAM Addr. Info. Prints the RAM data dump list.
04 RAM Edit Mode Factory use only.
06 RAM 00 Parameter Initialize Resets the Fax and Function parameters
Initialize to default values.
01 All Job Clear Clears all Jobs stored in Flash Memory.
02 LBP Error Log Clear Clears the Printer Error Log.
03 Shipment Set Clears All Jobs, All Preset Data,
Parameter Initialize & Resets the
Counters (Fax).
04 LBP Fuser Reset Clears the LBP fuser error.
07 Firmware 00 Host Program Updates the firmware in the machine with
Update (4MB) the Master Firmware Card.
01 Host Part A (2MB)
02 Host Part B (2MB)
03 EP Board (2MB)
04 LAN Board (2MB)
08 Firmware 00 Host Program Creates a Backup Firmware Card of the
Backup (4MB) machine’s firmware.
01 Host Part A (2MB)
02 Host Part B (2MB)
09 PC → Flash Card Creates a Master Firmware Card using
the Firmware Update Kit. A 2MB or 4MB
Flash Memory Card will be required
depending upon the model.
10 Page Memory Size Displays the page memory size (MB).
11 Sort Memory Size Displays the sort memory size (MB).
352
For DP-2500/3000
Service
Item Function
mode
F1 Self Test 00 CCD Test This test is used for checking the CCD.
01 LCD/LED Test This test is used for checking the LCD
and LEDs.
02 Page Memory Test This test is used for checking the Page
Memory.
03 Print Test Pattern 1 Prints the pattern for setting the Paper
position alignment.
04 Print Test Pattern 2 Factory use only.
05 PRT PWM Adj. Pattern Prints the gray steps when the Start key is
pressed. (Factory use only)
F2 Single Copy Test One sheet is copied when the Start key is
pressed.
F3 Continuous Copy Test Multi copies are made when the Start key
is pressed.
F4 Input / Output Status Test The functioning of Input / Output items
(selected item numbers) is checked.
F5 Function Parameters Various function settings (selected by
code numbers) can be changed.
F6 Adjustment Parameters Various function settings (selected by
code numbers) can be adjusted.
353
Service
Item Function
mode
F7 Electronic 00 Not Used
Counter 01 Key Operator ID Key Operator’s identification code for
access to the counter mode.
02 Maintenance 00 Total Count Total count for all copies / prints.
Count 01 PM Count Preventive Maintenance count.
02 Scanner PM Count PM count for scanner read.
03 ADF/iADF PM PM count for originals fed.
Count
04 Not Used
05 OPC Drum Count PM count for OPC Drum paper fed.
06 Process Unit Count PM count for Process Unit paper fed.
07 Paper Transport PM count for Paper Transport Unit paper
Count (See Note) fed.
08 ADU Count PM count for Automatic Duplex Unit
(See Note) paper fed.
09 Dual-Path Count PM count for Dual-Path Exit Guide Unit
(See Note) paper fed.
03 Paper Feed 00 Sheet Bypass Total count of paper fed from the sheet
Count Count bypass.
01 1st Paper Tray Total count of paper fed from the 1st
Count paper tray.
02 2nd Paper Tray Total count of paper fed from the 2nd
Count paper tray.
03 3rd Paper Tray Total count of paper fed from the 3rd
Count paper tray.
04 4th Paper Tray Total count of paper fed from the 4th
Count paper tray.
04 Scanner 00 ADF/iADF Count Total count of originals fed through the
Count ADF/iADF.
01 ADF/iADF Read Total count of originals scanned through
Count the ADF/iADF.
02 Scanner Count Total count of scanning operations.
03 Scanner Read Total count of scanner read.
Count
05 Copy Count 00 Copy Print Count Total count of copies printed.
01 Copy Scan Count Total count of copies scanned.
06 PC Count 00 PC Print Count Total count printed from PC.
01 PC Scan Count Total count scanned from PC.
08 Fax Count 00 Fax Transmit Count Total count of Fax transmitted.
01 Fax Receive Count Total count of Fax received.
02 Fax Print Count Total count of Fax printed.
09 Clear All Counts All counters are cleared.
354
Service
Item Function
mode
F8 Service Adjustment Perform pseudo-operation of an item
(selected by code numbers)
00 CHK Mirror Movement When replacing the exposure lamp.
Procedure:
a) Press the Start key to move the
exposure lamp to the position (approx.
250mm from the optics home position)
where it can be replaced.
b) To return the optical system to the
home position, press the CLEAR key.*
06 Error Log Print/View a) Each time the arrow key is pressed,
the machine errors or paper jam codes
stored in memory are displayed,
beginning with the oldest code.
Note:
Only the 30 most recent codes are
displayed.
07 Error Log Clear a) Press the Reset key.
A Message "Error code can be cleared
with the Start key" is displayed on the
LCD.*
b) Press the Start key.
12 Orginal Size Sensor Adjust the slice level for the original size
detection sensors automatically. Execute
this mode by closing the platen cover.
19 Move Mirror To Lock a) Press the Start key then the mirror unit
moves to locked position for
transporting the copier.
b) When the mirror unit is locked, any
digit key input is not be accepted.
Note:
The lock operation is automatically
reset when the Power switch is turned
ON again.
47 ADF Continuous Test Press START key to start.
48 Platen Continuous Test Press START key to start.
355
Service
Item Function
mode
F9 Unit 00 Fax Function Parameters
Maintenance 01 Service Alert Tel # Displays the contact number when a
machine malfunction occurs.
02 Firmware 00 Host Displays the firmware version for host.
Version 01 Control Panel Displays the firmware version for control
(For DP-2500/3000) panel.
02 Scanner Displays the firmware version for scanner.
03 Printer Displays the firmware version for printer.
04 Finisher Displays the firmware version for finisher.
05 Printer Board (PDL) Displays the firmware version for PDL.
06 LAN Board Displays the firmware version for LAN.
07 G3B Board Displays the firmware version for G3B
Board.
08 Modem Displays the firmware version for modem.
09 3rd Paper Feed Displays the firmware version for 3rd
Module Paper Feed Module.
03 Print Device 00 F5/F6 Parameters Prints the memory contents of the F5 and
Info. F6 modes.
01 Printer Report Prints the printer report.
02 Counter Information Prints the counter information.
03 System Addr. Info. Prints the system memory setting.
04 RAM Addr. Info. Prints the RAM data dump list.
04 RAM Edit Mode Factory use only.
06 RAM 00 Parameter Initialize Resets the Fax and Function parameters
Initialize to default values.
01 All Job Clear Clears all Jobs stored in Flash Memory.
02 LBP Error Log Clear Clears the Printer Error Log.
03 Shipment Set Clears All Jobs, All Preset Data,
Parameter Initialize & Resets the
Counters (Fax).
04 LBP Fuser Reset Clears the LBP fuser error.
07 Firmware 00 Host Program Updates the firmware in the machine with
Update (4MB) the Master Firmware Card.
01 Host Part A (2MB)
02 Host Part B (2MB)
03 EP Board (2MB)
04 LAN Board (2MB)
08 Firmware 00 Host Program Creates a Backup Firmware Card of the
Backup (4MB) machine’s firmware.
01 Host Part A (2MB)
02 Host Part B (2MB)
09 PC → Flash Card Creates a Master Firmware Card using
the Firmware Update Kit. A 2MB or 4MB
Flash Memory Card will be required
depending upon the model.
10 Page Memory Size Displays the page memory size (MB).
11 Sort Memory Size Displays the sort memory size (MB).
356
5.1.3. F4 Mode: Input/Output Check
For DP-2000
Set the machine to service mode and press "4" on the Keypad.
↓
Press the “START” key.
↓
Select the Check Input or Check Output on the Control Panel.
↓
Enter the number to activate the test then press “START” key.
↓
Press “STOP” key to cancel the test.
↓
When the “CLEAR” key is pressed, the selected code input will not be accepted.
↓
Press “FUNCTION” and “CLEAR” key to exit the service mode.
For DP-2500/3000
Set the machine to service mode and press "4" on the Keypad.
↓
Press the “START” key.
↓
Select the Check Input or Check Output on the Touch Panel display.
↓
Enter the number to activate the test then press “START” key.
↓
Press “STOP” key to cancel the test.
↓
When the “CANCEL” key is touched, the selected code input will not be accepted.
↓
Press “FUNCTION” and “CLEAR” key to exit the service mode.
357
1. Input Check
For DP-2000/2500/3000
Message Display
No. Function Condition Remark
7 6 5 4 3 2 1 0
000 Not Used
001 Paper Registration Sensor is activated. 1
Sensor (4th Paper Tray)
Paper Registration Sensor is activated. 1
Sensor (3rd Paper Tray)
Paper Registration Sensor is activated. 1
Sensor (2nd Paper Tray)
002 Registration Sensor Sensor is activated. 1
Paper Eject Sensor Sensor is activated. 1
Dual-Path Exit Guide Unit Sensor is activated. 1
Eject Sensor
003 Finisher Staple Tray2 Paper is on the tray. 1
Finisher Tray Paper is on the tray. 1
004 Paper Transport Unit Sensor is activated. 1
Sensor 4
Paper Transport Unit Sensor is activated. 1
Sensor 3
Paper Transport Unit Sensor is activated. 1
Sensor 2
Paper Transport Unit Sensor is activated. 1
Sensor 1
005 Finisher Staple Tray Paper is on the tray. 1
006 Duplex Unit Sensor 4 Sensor is activated. 1
Duplex Unit Sensor 3 Sensor is activated. 1
Duplex Unit Sensor 2 Sensor is activated. 1
Duplex Unit Sensor 1 Sensor is activated. 1
007 Finisher Tray Home Tray in home position. 1
Position
Finisher Paper Feed Sensor is activated. 1
Sensor
JAM Access Cover Open Cover is open. 1
Detection Sensor
(4th Tray)
Paper Level Sensor Upper Limit is detected. 1
(4th Tray)
Paper Tray Sensor Paper Tray is detected. 1
(4th Tray)
NP Sensor (4th Tray) Paper is detected. 1
358
Message Display
No. Function Condition Remark
7 6 5 4 3 2 1 0
008 Finisher Tray Lower Limit Lower Limit is detected. 1
Finisher Tray Upper Limit Upper Limit is detected. 1
JAM Access Cover Open Door is open. 1
Detection Sensor
(3rd Tray)
Paper Level Sensor Upper Limit is detected. 1
(3rd Tray)
Paper Tray Sensor Paper Tray is detected. 1
(3rd Tray)
NP Sensor (3rd Tray) Paper is detected. 1
009 Finisher Back-Roller Home position is 1
Home Position detected.
Finisher Front Alignment Home position is 1
Plate Home Position detected.
JAM Access Cover Open Door is open. 1
Detection Sensor
(2nd Tray)
Paper Level Sensor Upper Limit is detected. 1
(2nd Tray)
Paper Tray Sensor Paper Tray is detected. 1
(2nd Tray)
NP Sensor (2nd Tray) Paper is detected. 1
010 Finisher End Alignment Home position is 1
Plate Home Position detected.
Finisher Lever Home Home position is 1
Position detected.
JAM Access Cover Open Cartridge is detected. 1
Detection Sensor
(1st Tray)
Paper Level Sensor Upper Limit is detected. 1
(1st Tray)
Paper Tray Sensor Paper Tray is detected. 1
(1st Tray)
NP Sensor (1st Tray) Paper is detected. 1
011 Finisher Stapler detecting Stapler is not detected. 1
Sensor
Finisher Stapler Cartridge Home position is not 1
Home Position detected.
Sheet Bypass Paper Paper is detected. 1
Length
Sheet Bypass Paper Paper is detected. 1
Length (A3)
Sheet Bypass Paper Paper is detected. 1
Length (B4)
Sheet Bypass NP Sensor Paper is detected. 1
359
Message Display
No. Function Condition Remark
7 6 5 4 3 2 1 0
012 Finisher Stapler Top Stapler top is detected. 1
Finisher Interlock Finisher Interlock is 1
actuated.
Waste Toner Box Sensor Toner Cartridge is 1
detected.
Paper Transport Unit Door Paper Transport Unit Door 1
Sensor is closed.
Front Cover Sensor Front Cover is closed. 1
Micro Switch Right Side Door is closed. 1
013- Not Used
019
020 Size Sensor 3 Original is on the C point. 1 Z
360
2. Output check
Press the “START” key to start and press the “STOP” key to reset.
For DP-2000/2500/3000
361
No. Item Function Remark
075 3rd Tray Motor Activate 3rd Tray Motor after
pressing Start key.
076 3rd Tray Feed Roller Clutch Activate 3rd Tray Paper Drive Clutch
after pressing Start key.
077 3rd Tray Lift DC Motor Activate 3rd Tray Lift DC Motor after
pressing Start key.
078 3rd Intermediate Roller Clutch Activate 3rd Idle Clutch after pressing
Start key.
079 Not Used
080 4th Tray Feed Roller Clutch Activate 4th Tray Paper Drive Clutch
after pressing Start key.
081 4th Tray Lift DC Motor Activate 4th Tray Lift DC Motor after
pressing Start key.
082 4th Intermediate Roller Clutch Activate 4th Idle Clutch after pressing
Start key.
083- Not Used
084
085 Multi Feeder Feed Roller Clutch Activate Sheet Bypass Clutch after
pressing Start key.
086- Not Used
099
100 Duplex Unit Solenoid (Eject 2) Activate Automatic Duplex Unit
Solenoid (Eject 2) after pressing Start
key.
101 Duplex Unit Solenoid (Eject 1) Activate Automatic Duplex Unit
Solenoid (Eject 1) after pressing Start
key.
102 Duplex Unit Motor Drive (Eject to Activate Automatic Duplex Unit Motor
Outer Tray) Drive (Eject to Outer Tray) after
pressing Start key.
103 Duplex Unit Motor Drive (Enter to Activate Automatic Duplex Unit Motor
Duplex Unit) Drive (Enter to Duplex Unit) after
pressing Start key.
104 Dual-Path Exit Guide Unit Activate Dual-Path Exit Guide Unit
Solenoid (Enter to Paper Solenoid (Enter to Paper Transport
Transport Unit) Unit) after pressing Start key.
105 Dual-Path Exit Guide Unit Activate Dual-Path Exit Guide Unit
Solenoid (Enter to Duplex Unit) Solenoid (Enter to Duplex Unit) after
pressing Start key.
106- Not Used
109
110 Finisher Paper Eject Motor Activate Finisher Paper Eject Motor
after pressing Start key.
111 Finisher Paper Alignment Motor Activate Finisher Paper Alignment
Motor after pressing Start key.
112 Finisher Front Alignment Motor Activate Finisher Front Alignment
Motor after pressing Start key.
113 Finisher End Alignment Motor Activate Finisher End Alignment
Motor after pressing Start key.
114 Finisher Stuck Tray Motor Activate Finisher Stuck Tray Motor
after pressing Start key.
362
No. Item Function Remark
115 Finisher Stapler Motor Activate Finisher Stapler Motor after
pressing Start key.
116- Not Used
119
120 CCD Assembly Activate CCD Assembly after
pressing Start key.
363
5.1.4. F5 Mode: Copier Function Parameters
For DP-2000
Set the machine to Service Mode and press "5" on the Keypad.
↓
Press the “START” key.
↓
Select the desired code number on the Control Panel.
↓
If you wish to select another code number, scroll the menu with the arrow keys (↑ ↓).
↓
Select the desired function on the Control Panel and press the “START” key.
↓
When the “CLEAR” key is pressed, the selected setting inputted will not be accepted.
↓
Press the “FUNCTION” and “CLEAR” key’s to exit the Service Mode.
For DP-2500/3000
Set the machine to Service Mode and press "5" on the Keypad.
↓
Press the “START” key.
↓
Select the desired code number on the Touch Panel display.
↓
If you wish to select another code number, scroll the menu with the arrow keys (←→).
↓
Select the desired function on the Touch Panel display and touch the “OK” key.
↓
When the “CANCEL” key is touched, the selected setting inputted will not be accepted.
↓
Press the “FUNCTION” and “CLEAR” key’s to exit the Service Mode.
For DP-2000/2500/3000
364
No. Item Function Factory setting
14 Paper Size (Tray 1) 0 : Ledger 0 (for North
1 : Legal America)
2 : Letter 5 (for Europe/
3 : Letter-R Other)
4 : INVOICE/A5-R
5 : A3
6 : A4
7 : A4-R
8 : B5
9 : B5-R
10 : A5-R
11 : FLS1
12 : FLS2
15 Paper Size (Tray 2) Same as F5-14 Same as F5-14
16 Paper Size (Tray 3) Same as F5-14 Same as F5-14
17 Paper Size (Tray 4) Same as F5-14 Same as F5-14
18-19 Not Used
20 ADF/iADF 0 : Off (Does not detect the option) 1
1 : Auto
Exit the service mode and reboot the
machine after setting the parameter to
activate the setting.
21 Finisher 0 : Off (Does not detect the option) 1
1 : Auto
Exit the service mode and reboot the
machine after setting the parameter to
activate the setting.
22 3rd Paper Feed Unit 0 : Off (Does not detect the option) 1
1 : Auto
Exit the service mode and reboot the
machine after setting the parameter to
activate the setting.
23 Paper Transport Unit 0 : Off (Does not detect the option) 1
1 : Auto
Exit the service mode and reboot the
machine after setting the parameter to
activate the setting.
24 ADU 0 : Off (Does not detect the option) 1
1 : Auto
Exit the service mode and reboot the
machine after setting the parameter to
activate the setting.
25 Dual-Path Guide Unit 0 : Off (Does not detect the option) 1
1 : Auto
Exit the service mode and reboot the
machine after setting the parameter to
activate the setting.
26 iADF 0 : Off (Does not detect the option) 1
1 : Auto
Exit the service mode and reboot the
machine after setting the parameter to
activate the setting.
27-31 Not Used
365
No. Item Function Factory setting
32 SADF Default 0 : No 0
1 : Yes
33 Not Used
34 Multi-Feed Default 0 : Off 0
1 : On
35 Sort Mode Default 0 : Non-sort 0
1 : Sort
2 : Staple
3 : Group
36 Output Tray (Inner) 0 : Off 1
1 : Auto
Exit the service mode and reboot the
machine after setting the parameter to
activate the setting.
37 Output Tray (Outer) 0 : Off 1
1 : Auto
Exit the service mode and reboot the
machine after setting the parameter to
activate the setting.
38 Duplex Mode Default 0 : No 0
1 : 1 to 2
2 : 2 to 2
3 : Book to 2
39 Not Used
40 Double Count 0 : No 1
(Total Counter, Key Counter, and 1 : Ledger/A3
Electronic Counter) 2 : Ledger/Legal/A3/B4
41 Count Up Timing 0 : At paper feed roller clutch 1
(and sheet bypass solenoid)
1 : At paper exit sensor
42 Key/Dept. Counter 0 : Not installed 0
1 : Key Counter Installed
2 : Departmental Counter
43 Key Counter Timing Same as F5-41 0
44 Insert Paper Count 0 : No 0
1 : Yes (Count the blank paper for OHP
Interleaving)
45-49 Not Used
50 Auto Exposure (T/P) 0 : No 2
1 : Yes
2 : Fix
51 Multisize Rotation 0 : No 0
(Image rotation at multi size 1 : Yes
original)
52 Original Size Detect 0 : Priority (Use the setting for F5-80) 1
(Auto original size detecting 1 : Yes (Detection)
sensor) 2 : No (No Detection)
53 Not Used
54 Margin Reduction 0 : No 0
1 : Yes
366
No. Item Function Factory setting
55 Margin Value Default 0 : 5mm 1
1 : 10mm
2 : 15mm
3 : 20mm
56 Edge Value Default 0 : 5mm 0
1 : 10mm
2 : 15mm
3 : 20mm
57 Book Value Default 0 : 5mm 1
1 : 10mm
2 : 15mm
3 : 20mm
58 Not Used
59 Copier Operation U13 0 : Stop (Copier stops or copy cycle is 0
(After "U13" Toner Box empty inhibited)
detection) 1 : Continue (Continuous copier operation)
60 Auto Tray Selection 0 : No (Manual) 1
1 : Yes (Auto)
61-62 Not Used
63 U13 Clear=After toner empty 0 : Any keys (When clearing U13, press any 0
detection key.)
(Copier stops or copy cycle 1 : User key (Press FUNCTION key and
inhibited) digit key 1.)
64-65 Not Used
66 Interleave Default 0 : Blank 0
1 : Copy
67-68 Not Used
69 Reduce N-in-1 Space 0 : No 0
1 : Yes
70 PM (Preventive Maintenance) 0 : No 10
1 : 1.5K
2 : 2.5K
3 : 5K
4 : 10K
5 : 15K
6 : 20K
7 : 30K
8 : 40K
9 : 60K
10 : 80K
11 : 90K
12 : 120K
13 : 160K
71 Not Used
72 Not Used
73 PM (OPC Drum) 0 : No (No indication)
(Preventive Maintenance for 1 : Service
OPC Drum) 2 : User
74 PM (Process Unit) 0 : No (No indication)
(Preventive Maintenance for 1 : Service
Process Unit) 2 : User
75 Not Used
367
No. Item Function Factory setting
76 Automatic Exposure (Text) 0 : No 2
1 : Yes
2 : Fix
77 Text Error Diffusion 0 : Off 1
1 : On (Execute error diffusion on Text
mode.)
78 A4/LTR Size Select 0 : No 0
1 : Yes (Set paper side to A4/LTR if original
or less than A4/LTR.)
79 Not Used
80 Paper Size Priority 0 : Ledger 2 (for North
1 : Legal American)
2 : Letter 8 (for European/
3 : Letter-R Other)
4 : INVOICE
5 : A3
6 : B4
7 : A4
8 : A4-R
9 : B5
10 : B5-R
11 : A5
12 : A5-R
13 : FLS1
14 : FLS2
81 B4/Foolscap Size 0 : B4 1
(for European version) 1 : Foolscap 1 (13” x 8")
2 : Foolscap 2 (13” x 8.5")
82 Manual Skyshot Mode 0 : Off1 : M1 On 0
2 : M2 On3 : M1, M2 On
83 Digital Skyshot 0 : No 1
1 : Normal
2 : Quality
84 Paper Tray Priority 0 : System (lower to upper) > Sheet bypass 1
(Left to Right) 1 : Copier (upper to lower) > Sheet bypass
85 Not Used
86 PM (Scanner) 0 : No 0
1 : 40K
2 : 60K
3 : 120K
4 : 240K
5 : 360K
6 : 480K
7 : 600K
87 PM (ADF/iADF) 0 : No 0
1 : 40K
2 : 60K
3 : 120K
4 : 240K
5 : 360K
6 : 480K
7 : 600K
88-89 Not Used
368
No. Item Function Factory setting
90 Beep Sound 0 : Off 1
1 : Soft
2 : Mid.
3 : Loud
91 M1, Size Y Set the default size for Manual Sky Shot 160
92 M1, Size X Mode, M1 and M2. 70
93 M2, Size Y 220
94 M2, Size X 95
95 Paper Size (FA) 0 : Japanese -
(Factory use only) 1 : North American
2 : European
3 : Other
96 Bypass Size (FA) 0 : Japanese -
(Factory use only) 1 : North American
2 : European
3 : Other
97 Not Used
98 Bypass B4/FLS (FA) 0 : B4 -
(Factory use only) 1 : Foolscap 1 (13” x 8")
2 : Foolscap 2 (13” x 8.5")
99 Not Used
369
5.1.5. F6 Mode: Adjustment and Programming
For DP-2000
Set the machine to Service Mode and press "6" on the Keypad.
↓
Press the "START" key.
↓
Select the desired code number on the Control Panel.
↓
If you wish to select another code number, scroll the menu with the arrow keys (↑ ↓).
↓
Select the desired function on the Control Panel and press the “START” key.
↓
When the “CANCEL” key is pressed, the selected setting inputted will not be accepted.
↓
Press the “FUNCTION” and “CLEAR” key’s to exit the Service Mode.
For DP-2500/3000
Set the machine to Service Mode and press "6" on the Keypad.
↓
Press the “START” key.
↓
Select the desired code number on the Touch Panel display.
↓
If you wish to select another code number, scroll the menu with the arrow keys (←→).
↓
Select the desired function on the Touch Panel display and touch the “OK” key.
↓
When the “CANCEL” key is touched, the selected setting inputted will not be accepted.
↓
Press the “FUNCTION” and “CLEAR” key’s to exit the Service Mode.
370
For DP-2000/2500/3000
Factory
No. Item Function Setting
setting
00 Main-scan direction magnification Adjustment of ratio for vertical -9 - +9 0.1% +4
ratio (vertical position to the paper position when scan is made.
feed direction) (standard = 100%)
01 Sub-scan direction magnification Adjustment of ratio for parallel -9 - +9 0.1% +4
ratio (parallel position to the paper position when scan is made.
feed direction)
02 Platen original registration Adjustment of platen original -30 - +30 0
detecting timing registration detection timing. 0.2mm
03 Copy paper registration detecting Delay time is adjusted from -30 - +30 0
timing (1st Tray) registration roller clutch ON. 0.25mm
04 Copy paper registration detecting Delay time is adjusted from -30 - +30 0
timing (Sheet Bypass) registration roller clutch ON. 0.25mm
05 Copy paper registration detecting Delay time is adjusted from -30 - +30 0
timing (2/3/4th Tray) registration roller clutch ON. 0.25mm
06 Copy paper registration detecting Delay time is adjusted from -30 - +30 0
timing (Auto. Duplex Unit) registration roller clutch ON. 0.25mm
07 Registration void of image Registration void should be 0 - +99 6
adjusted. 0.425mm
08 Trail edge detection timing of the Adjustment of trail edge void. -9 - 0 0
original image 0.5mm
09 Trail edge detection timing of the Adjustment of trail edge void. -9 - +15 -6
copy image 0.425mm
10-17 Not Used
18 Laser power compensation Laser power compensation -127 - 127 0
adjustment.
19 Bias standard voltage Adjustment of bias standard -127 - 127 0
voltage. 2.28V
20 Halftone Adjust Halftone adjustment, Print density -8 - +7 0
for Photo Mode.
(-) : Darker.
(+) : Lighter.
21-30 Not Used
31 Fuser temperature Adjustment of fuser temperature. -15 - +15 0
0.7°C
32-38 Not Used
39 LSU unit PWM Adjustment of PWM value of LSU. -32 - +32 0
40 Not Used
41 Paper loop (1st Tray) Adjustment for the length of the -8 - +7 0
loop formed before the copier 0.5mm
timing roller.
42 Paper loop (Sheet Bypass) Adjustment for the length of the -8 - +7 0
loop formed before the copier 0.5mm
timing roller.
43 Paper loop (2/3/4th Tray) Adjustment for the length of the -8 - +7 0
loop formed before the copier 0.5mm
timing roller.
371
Factory
No. Item Function Setting
setting
44 Paper loop (Auto. duplex unit) Adjustment for the length of the -8 - +7 0
loop formed before the copier 0.5mm
timing roller.
45-48 Not Used
49 Text mode image density Image density adjustment for Text -99 - +99 0
mode.
(-) : Darker.
(+) : Lighter.
50 Text/Photo mode image density Image density adjustment for Text/ -99 - +99 0
Photo mode.
(-) : Darker.
(+) : Lighter.
51 Photo mode image density Image density adjustment for -99 - +99 0
Photo mode.
(-) : Darker.
(+) : Lighter.
52 Not Used
53 CCD read timing Adjustment of CCD read position -44 - +44 -10
Exit the service mode and reboot 0.2mm
the machine after setting the
parameter to activate the setting.
54-68 Not Used
69 Stamp position adjustment Adjustment of verification stamp -7 - +7 0
position. 0.5mm
70-78 Not Used
79 MTF adjustment Adjustment of MTF. -127 - +127 0
80-82 Not Used
83 Laser Unit image side Laser write start position -8 - +7 0
(Sheet Bypass) adjustment (side to side 0.5mm
84 Laser Unit image side (1st Tray) adjustment).
85 Laser Unit image side (2nd Tray)
86 Laser Unit image side (3rd Tray)
87 Laser Unit image side (4th Tray)
88 Not Used
89 Laser Unit image side Laser write start position -8 - +7 0
(Auto. Duplex Unit) adjustment (side to side 0.5mm
adjustment).
90 ADF Image read start Adjustment of ADF horizontal -50 - +50 0
image read start position. 0.2mm
Exit the service mode and reboot
the machine after setting the
parameter to activate the setting.
91 ADF original lead edge registration Adjustment of original detection -99 - +99 8
timing. 0.2mm
92 Not Used
93 ADF original trail edge Adjustment of original trail edge -127 - 127 0
detection. 0.2mm
94 ADF magnification ratio (Top feed) Adjustment of ratio when the scan -9 - +9 0
is made. 0.1%
95-99 Not Used
372
5.1.6. F7 Mode: Electronic Counter
For DP-2000
Set the machine to Service Mode and press "7" on the Keypad.
↓
Press the “START” key.
↓
Select the desired code number on the Control Panel.
↓
If you wish to select another code number, scroll the menu with the arrow keys (↑ ↓).
↓
Select the desired function on the Control Panel and press the “START” key.
↓
When the “CLEAR” key is pressed, the selected setting inputted will not be accepted.
↓
Press the “FUNCTION” and “CLEAR” key’s to exit the Service Mode.
For DP-2500/3000
Set the machine to Service Mode and press "7" on the Keypad.
↓
Press the “START” key.
↓
Select the desired code number on the Touch Panel display.
↓
If you wish to select another code number, scroll the menu with the arrow keys (←→).
↓
Select the desired function on the Touch Panel display and touch the “OK” key.
↓
When the “CANCEL” key is touched, the selected setting inputted will not be accepted.
↓
Press the “FUNCTION” and “CLEAR” key’s to exit the Service Mode.
373
For DP-2000
Service
Item Function
mode
F7 Electronic 00 Not Used
Counter 01 Key Operator ID Key Operator’s identification code for
access to the counter mode.
Maintenance 02 Total Count Total count for all copies / prints.
Count 03 PM Count Preventive Maintenance count.
04 Scanner PM Count PM count for scanner read.
05 ADF/iADF PM Count PM count for originals fed.
06 OPC Drum Count PM count for OPC Drum paper fed.
07 Process Unit Count PM count for Process Unit paper fed.
08 Paper Transport PM count for Paper Transport Unit paper
Count fed.
09 ADU Count PM count for Automatic Duplex Unit
paper fed.
10 Dual-Path Count PM count for Dual-Path Exit Guide Unit
paper fed.
Paper Feed 11 Sheet Bypass Count Total count of paper fed from the sheet
Count bypass.
12 1st Paper Tray Count Total count of paper fed from the 1st
paper tray.
13 2nd Paper Tray Total count of paper fed from the 2nd
Count paper tray.
14 3rd Paper Tray Count Total count of paper fed from the 3rd
paper tray.
15 4th Paper Tray Count Total count of paper fed from the 4th
paper tray.
Scanner Count 16 ADF/iADF Count Total count of originals fed through the
ADF/iADF.
17 ADF/iADF Read Total count of originals scanned through
Count the ADF/iADF.
18 Scanner Count Total count of scanning operations.
19 Scanner Read Count Total count of scanner read.
F7 Electronic Copy Count 20 Copy Print Count Total count of copies printed.
Counter 21 Copy Scan Count Total count of copies scanned.
PC Count 22 PC Print Count Total count printed from PC.
23 PC Scan Count Total count scanned to PC.
Fax Count 24 Fax Transmit Count Total count of Fax transmitted.
25 Fax Receive Count Total count of Fax received.
26 Fax Print Count Total count of Fax printed.
99 Clear All Counts All counters are cleared.
374
For DP-2500/3000
Service
Item Function
mode
F7 Electronic 00 Not Used
Counter 01 Key Operator ID Key Operator’s identification code for
access to the counter mode.
02 Maintenance 00 Total Count Total count for all copies / prints.
Count 01 PM Count Preventive Maintenance count.
02 Scanner PM Count PM count for scanner read.
03 ADF/iADF PM Count PM count for originals fed.
04 Not Used
05 OPC Drum Count PM count for OPC Drum paper fed.
06 Process Unit Count PM count for Process Unit paper fed.
07 Paper Transport PM count for Paper Transport Unit paper
Count (See Note) fed.
08 ADU Count PM count for Automatic Duplex Unit
(See Note) paper fed.
09 Dual-Path Count PM count for Dual-Path Exit Guide Unit
(See Note) paper fed.
03 Paper Feed 00 Sheet Bypass Count Total count of paper fed from the sheet
Count bypass.
01 1st Paper Tray Count Total count of paper fed from the 1st
paper tray.
02 2nd Paper Tray Total count of paper fed from the 2nd
Count paper tray.
03 3rd Paper Tray Count Total count of paper fed from the 3rd
paper tray.
04 4th Paper Tray Count Total count of paper fed from the 4th
paper tray.
04 Scanner 00 ADF/iADF Count Total count of originals fed through the
Count ADF/iADF.
01 ADF/iADF Read Total count of originals scanned through
Count the ADF/iADF.
02 Scanner Count Total count of scanning operations.
03 Scanner Read Count Total count of scanner read.
F7 Electronic 05 Copy Count 00 Copy Print Count Total count of copies printed.
Counter 01 Copy Scan Count Total count of copies scanned.
06 PC Count 00 PC Print Count Total count printed from PC.
01 PC Scan Count Total count scanned to PC.
08 Fax Count 00 Fax Transmit Count Total count of Fax transmitted.
01 Fax Receive Count Total count of Fax received.
02 Fax Print Count Total count of Fax printed.
09 Clear All Counts All counters are cleared.
Note:
Available with Host Firmware version 2.xxxx or higher.
375
5.1.7. F8 Mode: Copier Operation Adjustment
For DP-2000
Set the machine to Service Mode and press "8" on the Keypad.
↓
Press the “START” key.
↓
Select the desired code number on the Control Panel.
↓
If you wish to select another code number, scroll the menu with the arrow keys (↑ ↓).
↓
Select the desired function on the Control Panel and press the “START” key.
↓
When the “CANCEL” key is pressed, the selected setting inputted will not be accepted.
↓
Press the “FUNCTION” and “CLEAR” key’s to exit the Service Mode.
For DP-2500/3000
Set the machine to Service Mode and press "8" on the Keypad.
↓
Press the “START” key.
↓
Select the desired code number on the Touch Panel display.
↓
If you wish to select another code number, scroll the menu with the arrow keys (←→).
↓
Select the desired function on the Touch Panel display and touch the “OK” key.
↓
When the “CANCEL” key is touched, the selected setting inputted will not be accepted.
↓
Press the “FUNCTION” and “CLEAR” key’s to exit the Service Mode.
376
For DP-2000/2500/3000
377
5.1.8. F9 Mode: System Maintenance
For DP-2000
Set the machine to Service Mode and press "9" on the Keypad.
↓
Press the “START” key.
↓
Select the desired code number on the Control Panel.
↓
If you wish to select another code number, scroll the menu with the arrow keys (↑ ↓).
↓
Select the desired function on the Control Panel and press the “START” key.
↓
When the “CANCEL” key is pressed, the selected setting inputted will not be accepted.
↓
Press the “FUNCTION” and “CLEAR” key’s to exit the Service Mode.
For DP-2500/3000
Set the machine to Service Mode and press "9" on the Keypad.
↓
Press the “START” key.
↓
Select the desired code number on the Touch Panel display.
↓
If you wish to select another code number, scroll the menu with the arrow keys (←→).
↓
Select the desired function on the Touch Panel display and touch the “OK” key.
↓
When the “CANCEL” key is touched, the selected setting inputted will not be accepted.
↓
Press the “FUNCTION” and “CLEAR” key’s to exit the Service Mode.
378
For DP-2000/2500/3000
Service
Item Function
mode
F9 Unit 00 Fax Function Parameters
Maintenance 01 Service Alert Tel # Displays the contact number when
amachine malfunction occurs.
02 Firmware 00 Host Displays the firmware version for host.
Version 01 Control Panel Displays the firmware version for control
(For DP-2500/3000) panel.
02 Scanner Displays the firmware version for scanner.
03 Printer Displays the firmware version for printer.
04 Finisher Displays the firmware version for finisher.
05 Printer Board (PDL) Displays the firmware version for PDL.
06 LAN Board Displays the firmware version for LAN.
07 G3B Board Displays the firmware version for G3B
Board.
08 Modem Displays the firmware version for modem.
09 3rd Paper Feed Displays the firmware version for 3rd
Module Paper Feed Module.
03 Print Device 00 F5/F6 Parameters Prints the memory contents of the F5 and
Info. F6 modes.
01 Printer Report Prints the printer report.
02 Counter Information Prints the counter information.
03 System Addr. Info. Prints the system memory setting.
04 RAM Addr. Info. Prints the RAM data dump list.
04 RAM Edit Mode Factory use only.
05 Not Used
06 RAM 00 Parameter Initialize Resets the Fax and Function parameters
Initialize to default values.
01 All Job Clear Clears all Jobs stored in Flash Memory.
02 LBP Error Log Clear Clears the Printer Error Log.
03 Shipment Set Clears All Jobs, All Preset Data,
Parameter Initialize & Resets the
Counters (Fax).
04 LBP Fuser Reset Clears the LBP fuser error.
07 Firmware 00 Host Program (4MB) Updates the firmware in the machine with
Update 01 Host Part A (2MB) the Master Firmware Card.
02 Host Part B (2MB)
03 EP Board (2MB)
04 LAN Board (2MB)
08 Firmware 00 Host Program (4MB) Creates a Backup Firmware Card of the
Backup 01 Host Part A (2MB) machine’s firmware.
02 Host Part B (2MB)
09 PC → Flash Card Creates a Master Firmware Card using
the Firmware Update Kit. A 2MB or 4MB
Flash Memory Card will be required
depending upon the model.
10 Page Memory Size Displays the page memory size (MB).
11 Sort Memory Size Displays the sort memory size (MB).
379
5.2. Service Modes (For Fax)
5.2.1. Service Mode Table
The following service modes are provided to assist you in setting operational functions of the unit and
determining the condition of the unit.
380
5.2.2. Service Mode 1 (Function Parameter Setting)
Use the following procedure to change the function parameters.
For DP-2000
7 Enter the new setting value. Ex: Enter "3" for Constant. ALARM STATUS:Const.
1:OFF 2:Tmr 3:CONST
8 Press “START”. The new value will be stored and the PARAMETER #002
next parameter will be displayed. STOP COMM.JRNL?
Note:
The following buttons provide these functions in the Service Mode:
"START": : The new setting value is stored in the machine.
"V” : Scroll the function parameter number down.
"/\ “ : Scroll the function parameter number up.
381
For DP-2500/3000
3 Press “MONITOR” four times, then press “*”. SERVICE MODE (1-9)
ENTER NO.
8 Press “START”. The new value will be stored and the SERVICE MODE
next parameter will be displayed. PARAMETER #002
STOP COMM.JRNL?
Note:
The following buttons provide these functions in the Service Mode:
"START": : The new setting value is stored in the machine.
"ORIGINAL SIZE / : Scroll the function parameter number down.
For USA INVOICE
For Other Countries A5
"ORIGINAL SIZE / : Scroll the function parameter number up.
For USA LETTER
For Other Countries A4
382
Function Parameter Table
No. Parameter Selections Function
000 MON/TEL DIAL 1 = Monitor Selects whether the machine starts to TX
2 = TEL/DIAL automatically during On-Hook dialing.
Monitor : Start to TX after pressing START
TEL/DIAL : Start to TX automatically
001 ALARM STATUS 1 = OFF Selects the No Paper or No Toner alarm status.
2 = Timer (6 sec.) OFF : Alarm is disabled.
3 = Constant Timer : Alarm will shut off after 6 seconds.
Constant : Alarm will not stop until "STOP" is
pressed or the error is cleared/corrected.
002 STOP COMM. 1 = Off Selects whether the machine prompts to print the
JRNL 2 = On COMM. Journal when the printout condition is set to
INC and STOP is pressed during communication.
003 CONTINUOUS 1 = Off Selects whether the Continuous Polling feature is
POLL 2 = Stn (Tx only) enabled.
3 = Hub (Rx only) Stn : Place the document(s) on the ADF or Platen,
then press the assigned Program Key to store
or add the documents into a polled file. (See
Note 1)
Hub : When the polling command is initiated, the
machine will continuously poll originals from
the remote stations until it is interrupted by
pressing "STOP".
004 NUMERIC ID 1 = Off (will not accept) Selects whether the machine accepts and allows to
SET 2 = On (accepts) set or change the Numeric ID.
005 COUNTRY (See next page)
CODE
383
Function Parameter Table
No. Parameter Selections Function
005 COUNTRY 000 : Austria Sets the country code after installing the Fax
CODE 001 : U.K. Communication Kit (DA-FG230).
002 : Canada Note:
003 : Denmark This parameter is preset at the factory to "999".
004 : Taiwan There is no need to change this parameter for
005 : Finland the following Country Suffixes as it is
006 : Germany automatically loaded by the Fax Host
007 : Netherlands Firmware.
008 : Italy PA : Australia
009 : Spanish PB : UK
010 : Hong Kong PF : France
011 : Australia PG : Switzerland
012 : Switzerland PK : China
013 : Norway PL : Portuguese
015 : Portuguese PM : Germany
016 : Ireland PS : Sweden
017 : Belgium PT : Taiwan
018 : Sweden PU : USA / Canada
019 : Turkey PV : Netherlands
020 : U.S.A. PX : Spain
021 : France PE : Other Countries 1
022 : New Zealand PQ : Other Countries 2
025 : Japan PY : Other Countries 3
030 : Czech
032 : Greece
038 : Malaysia
039 : China
045 : Thailand
048 : South Africa
049 : Singapore
050 : Universal
006 ID DISPLAY 1 = Number (Numeric ID) Selects the priority of displaying the ID.
2 = Chara (Character ID)
007 JNL COLUMN 1 = Preset station name Selects the contents of the ID to display on the
2 = Received ID Journal.
008 MONITOR 1 = Off Selects whether the Monitor is ON/OFF for
2 = On monitoring fax signals.
(FOR SERVICE USE ONLY)
009 DC LOOP 1 = Off (Normal) Selects a false Off Hook state for back to back
2 = On (Off Hook) communication test.
010 TX LEVEL 00 = 0 dBm Selects the TX signal output level, 0 to -15 dBm in 1
~ dBm steps. (Refer to Chapter 4.3.)
15 = -15 dBm
011 RX LEVEL 1 = -43 dBm Selects the receiving sensitivity of -33/-38/-43/-48
2 = -38 dBm dBm.
3 = -33 dBm
4 = -48 dBm
012 DTMF LEVEL 00 = 0 dBm Selects the DTMF output level, 0 to -15 dBm in 1
~ dBm steps.
15 = -15 dBm
384
Function Parameter Table
No. Parameter Selections Function
013 G3 RX EQL 1 = 0dB Selects the cable equalizer for G3 reception mode,
2 = 4dB 0dB, 4dB, 8dB or 12dB.
3 = 8dB
4 = 12dB
014 G3 TX EQL 1 = 0 dB Selects the cable equalizer for G3 transmission
2 = 4 dB mode, 0dB, 4dB, 8dB or 12dB.
3 = 8 dB
4 = 12 dB
015 Not Used
~
016
017 TX START 1 = 2400 bps Selects the transmission modem start speed, 14400/
2 = 4800 bps 12000/TC9600/TC7200/9600/7200/4800/2400 bps.
3 = 7200 bps Note:
4 = 9600 bps This parameter is applicable only when
5 = TC7200 bps communicating with regular G3 machines. When
6 = TC9600 bps communicating with Super G3 (V.34) machines,
7 = 12000 bps use Parameter No. 32.
8 = 14400 bps
018 RX START 1 = 2400 bps Selects the reception modem start speed, 14400/
2 = 4800 bps 12000/TC9600/TC7200/9600/7200/4800/2400 bps.
3 = 7200 bps Note:
4 = 9600 bps This parameter is applicable only when
5 = TC7200 bps communicating with regular G3 machines. When
6 = TC9600 bps communicating with Super G3 (V.34) machines,
7 = 12000 bps use Parameter No. 33.
8 = 14400 bps
019 ITU-T V.34 1 = Off Selects whether the ITU-T V.34 is Off, On or Select.
2 = On Select: Select whether the ITU-T V.34 is Off or On,
3 = Select when entering Phone Book Dialing Numbers
or Manual Number Dialing.
020 ITU-T ECM 1 = Off (Invalid) Select the ECM mode.
2 = On (Valid)
021 EP TONE 1 = Off (without EP Tone) Selects whether to add the echo protect tone on V.29
2 = On (with EP Tone) mode.
(Used when Echo Suppression is disabled.)
On : Add
Off : Do not add
022 SIGNAL 1 = 100 ms Selects the time interval between the receiving signal
INTERVAL 2 = 200 ms and the transmitting signal.
3 = 500 ms
023 TCF CHECK 1 = Normal (Short) Selects the TCF check interval Long/Short
2 = Long
024 CED 1 = 1080 Hz (non ITU-T) Selects the CED frequency 2100/1080 Hz
FREQUENCY 2 = 2100 Hz
025 COMM. START- 1 = 1’st response Selects the communication start-up condition (XMT
UP 2 = 2’nd response and Polling).
(Used when Echo Suppression is disabled.)
026 NON- 1 = Off (Invalid) Selects own mode (Panafax mode).
STANDARD 2 = On (Valid)
027 SHORT 1 = Off (Invalid) Selects the short protocol mode.
PROTOCOL B 2 = On (Valid)
385
Function Parameter Table
No. Parameter Selections Function
028 SHORT 1 = Off (Invalid) Selects the short protocol mode. When activated, it
PROTOCOL D 2 = On (Valid) allows the machine to automatically store the modem
speed for each Auto Dial Number.
029 REMOTE 1 = Off (will not accept) Selects whether the machine accepts Remote
DIAGNOSTICS 2 = On (accepts) Diagnostics from the service station.
030 CED & 300 bps 1 = 75 ms Selects the pause interval between the CED and the
2 = 1 sec 300 bps signal.
(Used when Echo Suppression is disabled.)
031 RTC = EOLx12 1 = Off (EOLx6) Selects the RTC signal, EOLx6 or EOLx12.
2 = On (EOLx12)
032 V34 TX START 2400-33600bps Selects the transmission modem start speed for V.34
communication, 33600-2400 bps.
033 V34 RX START 2400-33600bps Selects the receiving modem start speed for V.34
communication, 33600-2400 bps.
034 V34 TX Symbol 2400-3429sr Selects the transmission symbol rate for V.34, 3429/
Rate 3200/3000/2800/2400 sr.
For DP-2000
Press “V” or “/\ “ to select the symbol rate.
For DP-2500/3000
Press the following ORIGINAL SIZE keys to
select the symbol rate:
For USA LETTER and INVOICE
For Other Countries A4 and A5
035 V34 RX Symbol 2400-3429sr Selects receiving symbol rate for V.34, 3429/3429/
Rate 3200/3000/2800/2400 sr.
For DP-2000
Press “V” or “/\ “ to select the symbol rate.
For DP-2500/3000
Press the following ORIGINAL SIZE keys to
select the symbol rate:
For USA LETTER and INVOICE
For Other Countries A4 and A5
036 Not Used
037 PROTOCOL 1 = Off (not displayed) Selects whether to display the modem speed during
DISPLAY 2 = On (displayed) communication.
(Press the Job Status Key to display)
038 Not Used
039 FLASH TIME 5 = 50 ms Selects the pause interval before activating the Flash
~ key.
100 = 1000 ms
040 E/F TIME 5 = 50 ms Selects the pause interval before activating the Flash
(For Germany, ~ key.
Austria and 100 = 1000 ms
Switzerland only)
041 PAUSE TIME 1 = 1 sec. Selects the pause interval from 1 sec. ~ 10 sec. for
~ dialing through a switchboard or for international
10 = 10 sec. calls.
042 Not Used
386
Function Parameter Table
No. Parameter Selections Function
043 REDIAL 0 = no waiting Selects the redial interval from 0 to 15 minutes in 1
INTERVAL ~ minute steps.
15 = 15 minutes
044 REDIAL COUNT 0 = no redial Selects the redial count from 0 to 15 times in 1 step
~ intervals.
15 = 15 times Note:
In order to comply with the requirements TBR21 in
the EC countries, do not select 15 times.
045 RING DETECT 1 = 1 ring Selects the ring detection count from 1 to 9 rings in 1
COUNT ~ ring step intervals.
9 = 9 rings
046 ON-HOOK TIME 0 = 0 sec. Selects the on-hook time between sequential
~ communication calls in 1 second step intervals.
90 = 90 sec.
047 RESPONSE 1 = 1 sec. Selects the waiting interval for the response after
WAIT ~ completing the dialing.
90 = 90 sec.
048 Not Used
049
050 RING DETECT 1 = Normal Selects the quality of ringer detection. Use if the line
MODE 2 = Rough signal is out of regulation, set to "Rough" so that the
unit may detect the ringing signals.
051 Not Used
052 PULSE RATE 1 = 10 pps Selects the dial pulse rate 10/20 pps.
2 = 20 pps
053 Not Used
054
055 BUSY TONE 1 = Off Selects whether to detect the Busy Tone.
CHECK 2 = On
056 DIAL TONE 1 = Off Selects whether to detect dial tone before dialing the
CHECK 2 = On telephone number.
(Except for USA
and Canada)
057 DC LOOP 1 = Off (will not check) Selects whether the unit checks the DC Loop during
CHECK 2 = On (checks) communication.
(Except for USA
and Canada)
058 COMM.JRNL 1 = Off (without image) Selects whether the machine prints the COMM.
+IMAGE 2 = On (with image) Journal with image.
059 CONFIDENTIAL 1 = Off (does not print out) Selects whether the machine prints the Confidential
RCV REPORT 2 = On (prints out) RCV Report.
060 VERSION Indicates the Host software
version.
061 TX/RX//PRT/ TX/RX/PRT/CPY Displays the transmitted, received, total printed and
CPY COUNTER copied document count.
062 PRINT 1 = Off Selects whether to print in the Fax Parameter List,
COUNTER 2 = On the counter information that is displayed in the
Function Parameter No. 61.
063 Not Used
~
067
387
Function Parameter Table
No. Parameter Selections Function
068 NYSE FAX 1 = Off Selects whether the machine will forward the
FORWARD 2 = On incoming and outgoing faxes to a specified station.
Note:
Once this parameter is activated, Fax Forwarding
via Fax Parameter 054 is automatically disabled,
an Access Code of "0000" is automatically
assigned and Fax Parameter 038 has a new
setting added called "NYSE".
069 NYSE LOCAL 1 = INC Selects the printing condition for the incoming faxes
PRINT 2 = ON (Always) after FAX Forwarding.
INC. : Prints only if FAX Forwarding fails.
ON : Always prints.
070 LINE ERROR 1 = 128 lines 1. Selects the line disconnect condition during
2 = 256 lines reception. If the number of line errors exceed this
3 = 512 lines setting, the unit will disconnect the line.
4 = 1024 lines 2. Selects the transmit condition of RTP/PIP or RTN/
5 = 2048 lines PIN.
6 = Off (Available if No.73 Error Detect is set to "LINES")
(will not disconnect line) (See Note 1)
071 TOTAL ERROR 1 = 5% Selects the transmit condition of RTP/PIP or RTN/
2 = 10% PIN.
3 = 15% (Available if No.73 Error Detect is set to "RATE".)
4 = 20% (See Note 2)
072 CONTINUOUS 1 = Off (unlimited) Selects the continuous total error criteria of Off/3/6 or
ERROR 2 = 3 lines/STD 12 lines in Standard mode. If continuous total error
3 = 6 lines/STD exceeds this setting, the unit will transmit RTN/PIN.
4 = 12 lines/STD (Available if No.73 Error Detect is set to "RATE".)
073 ERROR 1 = Lines Selects the error detect condition Lines/Rate.
DETECT 2 = Rate
074 RTN RECEIVE 1 = Disconnect Selects whether to disconnect the phone line or
2 = Continue continue when "RTN" is received.
075 CODING 1 = MH (MH only) Selects the coding scheme.
2 = MR (MH or MR)
3 = MMR
(MH or MR or MMR)
4 = JBIG
076 BATCH TX 1 = Off Selects whether the batch transmission is available.
2 = On
077 RX JAM 1 = Off (unlimited) Selects the maximum length of a received document
LENGTH 2=2m that can be printed.
3=8m
078 Not Used
079
080 ORIG. TOP -5.0 mm Adjusts the distance between the scanning sensor
FEED ~ ON position and the scanning start position.
+5.0 mm
081 ORIG. END -5.0 mm Adjusts the distance between the scanning sensor
FEED ~ OFF position and the scanning end position.
+5.0 mm
388
Function Parameter Table
No. Parameter Selections Function
082 JAM LENGTH 1=1m Selects the maximum length of the original that can
2=2m be scanned.
3=8m
4 = Unlimited
083 Not Used
084 LINE AS NO 1 = Ring (ring) Selects whether to ring or send a busy tone to the
PAPER 2 = Busy (keep line busy) remote station when the recording paper runs out or
the unit cannot receive because of any trouble.
085 Not Used
086 REDUCTION 1 = Off Selects whether the resolution is preset to Fine,
FINE 2 = On when sending with reduction B4→A4.
087 DARKER LEVEL 0 = Lightest Contrast Selects the contrast level.
088 NORMAL LEVEL ~ 0← →15
089 LIGHTER LEVEL 15 = Darkest Contrast Lightest← →Darkest
090 Not Used
091
092 SMOOTHING 1 = Off Selects whether the smoothing function is available.
2 = On
093 Not Used
~
109
110 MAC ADDRESS Indicates the MAC Address.
111 LAN I/F ROM Indicates the LAN I/F Firmware version.
VER
112 INSERT EMAIL 1 = Off Selects whether the Text Template (email message)
TXT 2 = On is programmable and added on all email sent in the
message body above the top line of text. (Up to 40
characters Programmed in the User Parameters.)
Note:
After enabling this feature, aside from entering the
text in the User Parameters, it also has to be
activated in each Auto Dial Number before it will
take effect. It does not work for Direct Dialed
Numbers.
113 Not Used
114 SYMBOL SET 1 = Standard Selects whether the extended symbols other than
2 = Extended "%" is available for Internet Parameters entry.
115 TIME ZONE 1 = Scroll Selects the setting method for Time Zone.
2 = Direct Scroll : Allows using "Scroll Keys" to scroll through
the Time Zone Table.
Direct : Allows you to input the Time Zone directly,
(*) key to be used as a switch between +/-.
116 OVERWRITE 1 = Yes Selects whether the Overwrite Warning is included
WARNING 2 = No on the Internet FAX Result Receipt when
programming the Auto Dialer via email.
117 Not Used
~
129
130 BUSY-ACK • In Busy Selects the signal timing between the BUSY and
TIMING • After Busy ACK signal in Printer Interface Mode.
• While Busy
389
Function Parameter Table
No. Parameter Selections Function
131 CMD RCV GRD 1 min. Selects the Guard Timer between each GDI
TIMER ~ Command in Printer Interface Mode.
15 min.
132 PRT DATA 1 min. Selects the Guard Timer between each GDI Data
TIMER ~ Frame in Printer Interface Mode.
15 min.
133 COLLATION 1 = Off Selects the Print Collation in Printer Interface Mode.
(PRT) 2 = On When “Auto” is selected, print collation will operate
3 = Auto according to the setting in Fax Parameter #65.
134 Not Used
135 JOB END TIMER 1 sec. Selects the Guard Timer while printing data with the
~ PDL Printer Driver ver. 6.
999 sec.
136 JAM 1 = Off Selects the JAM Recovery function in the PDL
RECOVERY 2 = On Printer Interface Mode.
Off: Printing performance is faster, however if a
paper jam occurs the jammed pages will not be
reprinted automatically.
On: Printing performance is slower, however if a
paper jam occurs the jammed pages will be
reprinted automatically.
137 Not Used
~
159
160 VERSION Indicates the ROM version PDL Firmware version
on the FRM PC Board.
161 Not Used
~
199
209 DC LOOP 1 = Off (Normal) Selects a false Off Hook state for back to back
2 = On (Off Hook) communication test.
210 TX LEVEL 00 = 0 dBm Selects the TX signal output level, 0 to -15 dBm in 1
~ dBm steps.
15 = -15 dBm
211 RX LEVEL 1 = -43 dBm Selects the receiving sensitivity of -33/-38/-43/-48
2 = -38 dBm dBm.
3 = -33 dBm
4 = -48 dBm
212 DTMF LEVEL 00 = 0 dBm Selects the DTMF output level, 0 to -15 dBm in 1
~ dBm steps.
15 = -15 dBm
213 G3 RX EQL 1 = 0dB Selects the cable equalizer for G3 reception mode,
2 = 4dB 0dB, 4dB, 8dB or 12dB.
3 = 8dB
4 = 12dB
214 G3 TX EQL 1 = 0dB Selects the cable equalizer for G3 transmission
2 = 4dB mode, 0dB, 4dB, 8dB or 12dB.
3 = 8dB
4 = 12dB
390
Function Parameter Table
No. Parameter Selections Function
217 TX START 1 = 2400 bps Selects the transmission modem start speed, 14400/
2 = 4800 bps 12000/TC9600/TC7200/9600/7200/4800/2400 bps.
3 = 7200 bps Note:
4 = 9600 bps This parameter is applicable only when
5 = TC7200 bps communicating with regular G3 machines. When
6 = TC9600 bps communicating with Super G3 (V.34) machines,
7 = 12000 bps use Parameter No. 232.
8 = 14400 bps
218 RX START 1 = 2400 bps Selects the reception modem start speed, 14400/
2 = 4800 bps 12000/TC9600/TC7200/9600/7200/4800/2400 bps.
3 = 7200 bps Note:
4 = 9600 bps This parameter is applicable only when
5 = TC7200 bps communicating with regular G3 machines. When
6 = TC9600 bps communicating with Super G3 (V.34) machines,
7 = 12000 bps use Parameter No. 233.
8 = 14400 bps
219 ITU-T V.34 1 = Off Selects whether the ITU-T V.34 is Off, On or Select.
2 = On (Select: Select whether the ITU-T V.34 is Off or On,
3 = Select when entering One-Touch/Abbreviated/
Phone book Dialing Numbers or Manual
Number Dialing.)
220 ITU-T ECM 1 = Off (Invalid) Select the ECM mode.
2 = On (Valid)
221 EP TONE 1 = Off (without EP Tone) Selects the echo protect tone on V.29 mode, On
2 = On (with EP Tone) (add) or Off (Not add).
(Used when Echo Suppression is disabled.)
222 SIGNAL 1 = 100 ms Selects the time interval between the receiving
INTERVAL 2 = 200 ms signal and the transmitting signal.
3 = 500 ms
223 TCF CHECK 1 = Normal (Short) Selects the TCF check interval Long/Short
2 = Long
224 CED 1 = 1080 Hz (non ITU-T) Selects the CED frequency 2100/1080 Hz
FREQUENCY 2 = 2100 Hz
225 COMM. START- 1 = 1’st response Selects the communication start-up condition (XMT
UP 2 = 2’nd response and Polling).
(Used when Echo Suppression is disabled.)
226 NON- 1 = Off (Invalid) Selects own mode (Panafax mode).
STANDARD 2 = On (Valid)
227 SHORT 1 = Off (Invalid) Selects the short protocol mode.
PROTOCOL B 2 = On (Valid)
228 SHORT 1 = Off (Invalid) Selects the short protocol mode.
PROTOCOL D 2 = On (Valid)
229 REMOTE 1 = Off (will not accept) Selects whether the machine accepts Remote
DIAGNOSTICS 2 = On (accepts) Diagnostics from the service station.
230 CED & 300 bps 1 = 75 ms Selects the pause interval between the CED and the
2 = 1 sec 300 bps signal.
(Used when Echo Suppression is disabled.)
231 RTC = EOLx12 1 = Off (EOLx6) Selects the RTC signal, EOLx6 or EOLx12.
2 = On (EOLx12)
232 V34 TX START 2400-33600bps Selects the transmission modem start speed in V.34
communication, 33600-2400 bps.
391
Function Parameter Table
No. Parameter Selections Function
233 V34 RX START 2400-33600bps Selects the receiving modem start speed in V.34
communication, 33600-2400 bps.
234 V34 TX Symbol 2400-3429sr Selects the transmission symbol rate for V.34, 3429/
Rate 3200/3000/2800/2400 sr.
For DP-2000
Press “V” or “/\ “ to select the symbol rate.
For DP-2500/3000
Press the following ORIGINAL SIZE keys to select
the symbol rate:
For USA LETTER and INVOICE
For Other Countries A4 and A5
235 V34 RX Symbol 2400-3429sr Selects receiving symbol rate for V.34, 3429/3429/
Rate 3200/3000/2800/2400 sr.
For DP-2000
Press “V” or “/\ “ to select the symbol rate.
For DP-2500/3000
Press the following ORIGINAL SIZE keys to select
the symbol rate:
For USA LETTER and INVOICE
For Other Countries A4 and A5
239 FLASH TIME 5 = 50 ms Selects the pause interval before activating the Flash
~ key.
100 = 1000 ms
240 E/F TIME 5 = 50 ms Selects the pause interval before activating the Flash
(For Germany, ~ key.
Austria and 100 = 1000 ms
Switzerland only)
241 PAUSE TIME 1 = 1 sec. Selects the pause interval from 1 sec. ~ 10 sec. for
~ dialing through a switchboard or for international
10 = 10 sec. calls.
245 RING DETECT 1 = 1 ring Selects the ring detection count from 1 to 9 rings in 1
COUNT ~ ring step intervals.
9 = 9 rings
247 RESPONSE 1 = 1 sec. Selects the waiting interval for the response after
WAIT ~ completing the dialing.
90 = 90 sec.
250 RING DETECT 1 = Normal Selects the quality of ringer detection. Use if the line
MODE 2 = Rough signal is out of regulation, set to "Rough" so that the
unit may detect the ringing signals.
252 PULSE RATE 1 = 10 pps Selects the dial pulse rate 10/20 pps.
2 = 20 pps
255 BUSY TONE 1 = Off Selects whether to detect the Busy Tone.
CHECK 2 = On
256 DIAL TONE 1 = Off Selects whether to detect dial tone before dialing the
CHECK 2 = On telephone number.
(Except for USA
and Canada)
257 DC LOOP 1 = Off (will not check) Selects whether the unit checks the DC Loop during
CHECK 2 = On (checks) communication.
(Except for USA
and Canada)
392
Function Parameter Table
No. Parameter Selections Function
260 VERSION Indicates the ROM version.
270 LINE ERROR 1 = 128 lines 1. Selects the line disconnect condition during
2 = 256 lines reception. If the number of line errors exceed this
3 = 512 lines setting, the unit will disconnect the line.
4 = 1024 lines 2. Selects the transmit condition of RTP/PIP or RTN/
5 = 2048 lines PIN.
6 = Off (Available if No. 273 Error Detect is set to
(will not disconnect line) "LINES")
(See Note 2)
271 TOTAL ERROR 1 = 5% Selects the transmit condition of RTP/PIP or RTN/
2 = 10% PIN.
3 = 15% (Available if No. 273 Error Detect is set to "RATE")
4 = 20% (See Note 3)
272 CONTINUOUS 1 = Off (unlimited) Selects the continuous total error criteria of Off/3/6 or
ERROR 2 = 3 lines/STD 12 lines in Standard mode. If continuous total error
3 = 6 lines/STD exceeds this setting, the unit will transmit RTN/PIN.
4 = 12 lines/STD (Available if No. 273 Error Detect is set to "RATE")
273 ERROR 1 = Lines Selects the error detect condition Lines/Rate.
DETECT 2 = Rate
275 MH/MR/MMR/ 1 = MH (MH only) Selects the coding scheme.
JBIG 2 = MR (MH or MR)
3 = MMR
(MH or MR or MMR)
4 = JBIG
393
Note 1: Continuous Polling (Station Mode)
This feature allows you to store or add documents into a polled file in memory.
To enable the Continuous Polling feature set Function Parameter No. 003 to “2:Station”. The last
Program Key will be assigned with the “Store 4 Poll” Key name automatically and cannot be
changed.
To prepare the document(s) to be polled, simply place the document(s) on the ADF or Platen and
then press the Program Key to store or add the document(s) into a polled file.
(Note: If a regular polled file is stored in memory, the Program Key for Continuous Polling will not
be accepted.)
Note 2: Function Parameter No. 070 and 270 (Line Error)-Transmit condition of RTP/PIP or RTN/PIN
Setting
Signal
1:128 2:256 3:512 4:1024 5:2048 6:Off
MCF/PIP 0-31 0-63 0-127 0-255 0-511 Always
RTP/PIP 32-63 64-127 128-255 256-511 512-1023 -
RTN/PIN 64-127 128-255 256-511 512-1023 1024-2047 -
Note 3: Function Parameter No. 071 and 271 (Total Error)-Transmit condition of RTP/PIP or RTN/PIN
Setting
Signal
1:5% 2:10% 3:15% 4:20%
MCF/PIP 0-2 0-4 0-7 0-9
RTP/PIP 3-4 5-9 8-14 10-19
RTN/PIN 5- 10- 15- 20-
Note 4: The default setting of parameters depends on the country’s specifications or regulations. Print the
Function Parameter List to confirm the default settings.
Note 5: The 200 series parameters are for 2nd G3 Fax Communication Port Kit (DA-FG231).
394
5.2.3. Service Mode 3 (Printout of Lists, Reports and Test Results)
From this Service Mode you can print the Function Parameter List, Page Memory Test, Printer Report, All
Document File, Protocol Trace and the Toner Order Form.
5.2.3.1. Function Parameter List
A list of all Function Parameters can be printed by the following procedure.
For DP-2000
395
For DP-2500/3000
3 Press “MONITOR” four times, then press “*”. SERVICE MODE (1-9)
ENTER NO.
6 After printing is completed, the unit returns to the SERVICE MODE (1-9)
display in step 3. ENTER NO.
396
Function Parameter List (Sample)
************* -FUNCTION PARAMETER- ************* DATE NOV-15-2000 ***** TIME 12:07 ***P.01
030 CED & 300bps:[75ms] 75ms 080 DOC TOP FEED:[0.0mm] 0.0mm
031 RTC=EQL x 12:[Off] Off 081 DOC END FEED:[0.0mm] 0.0mm
032 V34TX START:[33600bps] 33600bps 082 JAM LENGTH:[ 2 m] 2 m
033 V34RX START:[33600bps] 33600bps 083 ----------
034 V34 TX SR:[3429sr] 3429sr 084 LINE AS NOPAPER:[Ring] Ring
035 V34 RX SR:[3429sr] 3429sr 085 ----------
036 --------- 086 REDUCTION FINE:[On] On
037 PROTOCOL DISPLAY:[Off] Off 087 DARKER LEVEL:[2] 2
038 --------- 088 NORMAL LEVEL:[8] 8
039 FLASH TIME:[500] 500ms 089 LIGHTER LEVEL:[4] 4
Note:The power must be reset for the new parameter settings to take effect.
-PANASONIC DP-2500-
397
Function Parameter List (Sample)
************* -FUNCTION PARAMETER- ************* DATE NOV-15-2000 ***** TIME 12:07 ***P.02
Note:The power must be reset for the new parameter settings to take effect.
-PANASONIC DP-2500-
398
Function Parameter List (Sample)
************* -FUNCTION PARAMETER- ************* DATE NOV-15-2000 ***** TIME 12:07 ***P.03
Note:The power must be reset for the new parameter settings to take effect.
-PANASONIC DP-2500 -
Note:
1. [ ] - Factory Default
2. The contents of the Function Parameter List may vary depending on the country’s regulations.
3. “ * ” mark will be shown on the left side of number when setting was changed from default.
399
5.2.3.2. Page Memory Test
A test pattern prints out for checking the page memory (IC120 and IC121 on the SC PCB) and printer
mechanism using the following procedure.
For DP-2000
For DP-2500/3000
3 Press “MONITOR” four times, then press “*”. SERVICE MODE (1-9)
ENTER NO.
6 After printing is completed, the unit returns to the SERVICE MODE (1-9)
display in step 3. ENTER NO.
400
NOV-15-2000 15:00
VERSION: DP-2500 AAV11502PU
LBP ROM VERSION :400046
MEMORY SIZE: (2MB)
TX/RX/PRT/CPY:000123/000456/000789/000333
SHIPMENT SET
401
5.2.3.3. Printer Report
All printer errors are logged on the Printer Report which can be printed by the following procedure.
For DP-2000
For DP-2500/3000
3 Press “MONITOR” four times, then press “*”. SERVICE MODE (1-9)
ENTER NO.
6 After printing is completed, the unit returns to the SERVICE MODE (1-9)
display in step 3. ENTER NO.
402
**************-PRINTER REPORT-********************* DATE NOV-15-2000 ***** TIME 19:02********
CUSTOMER ID : 1234567890123456
403
1. Printer Error Detail Explanation
Recording Paper Jam Detection (From 1st Tray to Inner Tray 1)
Feed Solenoid
(nADF1)
Recording
Paper A sec
Size Setting
Ledger 2.3
Legal 1.9
A
A4 1.0
A4-R 1.5
Letter 1.1
Letter-R 1.4
Timing Sensor Invoice 1.1
(nRSENA)
0.36s
J01
Timing Sensor
did not turn ON
J01 will be logged when
nRSENA does not go low
0.02s
between 0.02sec to 0.59sec
0.59s after pADF1 goes high.
J30
Timing Sensor
did no turn OFF Recording
Paper B sec C sec
Size Setting
Ledger 2.1 2.7
Legal 1.7 2.3
J30 will be logged when nRSENA A4 0.9 1.4
does not go OFF between B sec to
B C A4-R 1.4 1.9
C sec after nRSENA goes ON.
Letter 0.9 1.5
Letter-R 1.2 1.8
Invoice 0.9 1.5
Paper Eject
Sensor Timing
(nESEN)
1.6s
J40
Paper Eject
Sensor did not 1.37s
turn ON
1.83s
404
Fuser Error Detection
405
LSU Error Detection
nPRINT
Print Start
nPMON
(CN701, 11)
Polygon Motor ON
nPMRDY
(CN701, 10) Normal Condition
Polygon Motor Ready
E1-22
nPMRDY
Polygon Motor does not
maintain constant speed.
pLDCTL
(CN701, 6)
Laser Timing Signal
0.24 ms (600 x 600dpi) 0.37 ms (16 x15.4 line/mm: Not Rotate Print)
0.36 ms (400 x 400dpi) 0.35 ms (16 x 15.4 line/mm: Rotate Print)
Normal Condition
nHSYNC
(CN701, 2)
Laser Timing Detection
E1-20
nHSYNC
(CN701, 2)
Can not detect
Laser Timing
nHSYNC timing signal is less than 60% of Normal Condition
406
Out of Toner Detection
Toner Sensor Output Signal
Status A
(Enough toner in the cartridge)
Status B
(Remaining toner
2V is getting low)
1V
Mixing blade
rotating cycle
0V
Toner Sensor output may change when the mixing blade passes above the Toner Sensor. Therefore
the output signal has a max. voltage and min. voltage during mixing blade rotation cycle (2.1 sec.).
E043 (U13)
If the unit detects Status B, 10 times during printing, the machine recognizes that the remaining toner is
low and the display shows "REPLACE TONER CARTRIDGE".
E041 (U13)
After detecting E043 and the LBP Print Available Counter Value reaches "0" (after 300 pages are
printed), the unit logs E041 (OUT OF TONER).
E45 (U13)
If the Waste Toner Box is not installed, the unit logs E045 and displays “NO WASTE TONER BOX”.
407
5.2.3.4. All Document Files
Print the document files from the Flash Memory.
For DP-2000
For DP-2500/3000
3 Press “MONITOR” four times, then press “*”. SERVICE MODE (1-9)
ENTER NO.
6 After printing is completed, the unit returns to the SERVICE MODE (1-9)
display in step 3. ENTER NO.
408
5.2.3.5. Protocol Trace
Print a Protocol Trace Report for the previous communication.
For DP-2000
For DP-2500/3000
3 Press “MONITOR” four times, then press “*”. SERVICE MODE (1-9)
ENTER NO.
409
Step Operation or Unit Condition LCD Display
6a Press “START”. SERVICE MODE
PROTOCOL TRACE
* PRINTING *
7 After printing is completed, the unit returns to the SERVICE MODE (1-9)
display in step 3. ENTER NO.
Note:
This field (LINE-1 or LINE-2) appears only when the 2nd G3 Fax Communication Port Kit is installed.
*************** PROTOCOL LOG. REPORT ****************** DATE NOV-15-2000 ***** TIME 16:56 *******
STATUS : OK
MODE : ECM-TX (STANDARD)
SPEED : 9600bps 0MS/L
REMOTE CAPA. : DIS 00 CE B9 C4 80 12
LOCAL CAPA. : TSI 2B 20 20 20 38 37 2B 2B 2B 2B
39 38 36 36 35 34 37 38 38 30
DCS 00 C6 F8 44
COMMAND LOG.
REMOTE : NSF CSI DIS CFR
LOCAL : TSI DCS PIX PPS-EOP
------------------------------------------------------------------
REMOTE : MCF
LOCAL : DCN
-PANASONIC DP-2500-
****************************-PANASONIC DP-2500-*************-12345678901234567890-*****************
410
5.2.3.6. Toner Cartridge Order Form
The Toner Cartridge Order Form can be printed out manually by the following procedure.
For DP-2000
For DP-2500/3000
3 Press “MONITOR” four times, then press “*”. SERVICE MODE (1-9)
ENTER NO.
6 After printing is completed, the unit returns to the SERVICE MODE (1-9)
display in step 3. ENTER NO.
411
*************************************
> TONER CARTRIDGE ORDER FORM <
*************************************
**** The toner supply in your machine is running low **** (1)
To order a replacement Cartridge from your Authorized Dealer
Attention: Attention:
Quantity Required:
/ /
Print your name and title Signature & Date
Explanation of Contents
(1) Low Toner Message (Fixed) “The toner supply in your machine is running low”
(2) Dealer Name Up to 25 digits
(3) Toner Order Tel # Up to 36 digits
(4) Toner Order Fax # Up to 36 digits
(5) Customer ID Up to 16 characters (User Identification Code)
(6) Toner Cartridge No. DQ-TU18B
412
5.2.4. Service Mode 4 (Modem Test)
5.2.4.1. Binary Signal
This Service Mode is used to check the binary signal output. Signals can be output to the line using the
following procedure.
For DP-2000
7 Enter the signal number (1-9) to select the binary SIGNAL TEST
signal. 300bps
For DP-2500/3000
3 Press “MONITOR” four times, then press “*”. SERVICE MODE (1-9)
ENTER NO.
413
Step Operation or Unit Condition LCD Display
6 Press “START”. SERVICE MODE
SIGNAL TEST
7 Enter the signal number (1-9) to select the binary SERVICE MODE
signal. SIGNAL TEST
300bps
Note:
This field (LINE-1 or LINE-2) appears only when the 2nd G3 Fax Communication Port Kit is installed.
414
5.2.4.2. Tonal Signal
This Service Mode is used to check the tonal signal output. Signals can be output to the line using the
following procedure.
For DP-2000
7 Enter the signal number (1-7) to select the binary TONAL TEST
signal. 1080Hz
For DP-2500/3000
3 Press “MONITOR” four times, then press “*”. SERVICE MODE (1-9)
ENTER NO.
415
Step Operation or Unit Condition LCD Display
6 Press “2” and “START”. SERVICE MODE
TONAL TEST
7 Enter the signal number (1-7) to select the binary SERVICE MODE
signal. TONAL TEST
1080Hz
Note:
This field (LINE-1 or LINE-2) appears only when the 2nd G3 Fax Communication Port Kit is installed.
416
5.2.4.3. DTMF Signal
This Service Mode is used to check the DTMF (Dual Tone Multi Frequency) signal output.
The DTMF signal can be generated using the following procedure.
For DP-2000
8a Enter the signal number (1-8) to select the DTMF SINGLE TONE
signal.
7b Press "2" and "START" for Dual Tone Generation. SINGLE TONE
697Hz
8b Enter the signal number (0-#) to select the DTMF Dual DUAL TONE
tone. (0)
For DP-2500/3000
3 Press “MONITOR” four times, then press “*”. SERVICE MODE (1-9)
ENTER NO.
417
Step Operation or Unit Condition LCD Display
5 Press “START”. SERVICE MODE
Use the ORIGINAL SIZE keys to scroll to the desired MODEM TEST (1-5)
Modem Test. 1:SIGNAL TEST
8a Enter the signal number (1-8) to select the DTMF SERVICE MODE
signal. SINGLE TONE
697Hz
7b Press "2" and "START" for Dual Tone Generation. SERVICE MODE
DUAL TONE
8b Enter the signal number (0-#) to select the DTMF Dual SERVICE MODE
tone. DUAL TONE
(0)
Note:
This field (LINE-1 or LINE-2) appears only when the 2nd G3 Fax Communication Port Kit is installed.
418
DTMF Single Tone Table
Number DTMF Signal Tones
1 697 Hz
2 770 Hz
3 852 Hz
4 941 Hz
5 1209 Hz
6 1336 Hz
7 1477 Hz
8 1633 Hz
DTMF Dual Tone Table
Number DTMF Dual Tones
0 941 Hz + 1336 Hz
1 697 Hz + 1209 Hz
2 697 Hz + 1336 Hz
3 697 Hz + 1477 Hz
4 770 Hz + 1209 Hz
5 770 Hz + 1336 Hz
6 770 Hz + 1477 Hz
7 852 Hz + 1209 Hz
8 852 Hz + 1336 Hz
9 852 Hz + 1477 Hz
* 941 Hz + 1209 Hz
# 941 Hz + 1477 Hz
419
5.2.4.4. Binary Signal (V.34)
This Service Mode is used to check the binary signal output. Signals can be output to the line using the
following procedure. (V.34)
For DP-2000
7 Enter the signal number (01-61) and press [SET] to V.34 MODEM TEST
select the binary signal. V34 2400sr 2400bps
8 Press "CLEAR" to end the signal generation. To select V.34 MODEM TEST
another signal, repeat step 7. ENTER NO._
For DP-2500/3000
3 Press “MONITOR” four times, then press “*”. SERVICE MODE (1-9)
ENTER NO.
420
Step Operation or Unit Condition LCD Display
6 Press “4” and “START”. SERVICE MODE
V.34 MODEM TEST
7 Enter the signal number (01-61) and press [SET] to SERVICE MODE
select the binary signal. V.34 MODEM TEST
V34 2400sr 2400bps
Note:
This field (LINE-1 or LINE-2) appears only when the 2nd G3 Fax Communication Port Kit is installed.
421
Binary Signal Table
Number Signals Number Signals Number Signals
01 V34 2400 sr 2400 bps 22 V34 3000 sr 9600 bps 43 V34 3429 sr 4800 bps
02 V34 2400 sr 4800 bps 23 V34 3000 sr 12000 bps 44 V34 3429 sr 7200 bps
03 V34 2400 sr 7200 bps 24 V34 3000 sr 14400 bps 45 V34 3429 sr 9600 bps
04 V34 2400 sr 9600 bps 25 V34 3000 sr 16800 bps 46 V34 3429 sr 12000 bps
05 V34 2400 sr 12000 bps 26 V34 3000 sr 19200 bps 47 V34 3000 sr 19200 bps
06 V34 2400 sr 14400 bps 27 V34 3000 sr 21600 bps 48 V34 3429 sr 16800 bps
07 V34 2400 sr 16800 bps 28 V34 3000 sr 24000 bps 49 V34 3429 sr 19200 bps
08 V34 2400 sr 19200 bps 29 V34 3000 sr 26400 bps 50 V34 3429 sr 21600 bps
09 V34 2400 sr 21600 bps 30 V34 3000 sr 28800 bps 51 V34 3429 sr 24000 bps
10 V34 2800 sr 4800 bps 31 V34 3200 sr 4800 bps 52 V34 3429 sr 26400 bps
11 V34 2800 sr 7200 bps 32 V34 3200 sr 7200 bps 53 V34 3429 sr 28800 bps
12 V34 2800 sr 9600 bps 33 V34 3200 sr 9600 bps 54 V34 3429 sr 31200 bps
13 V34 2800 sr 12000 bps 34 V34 3200 sr 12000 bps 55 V34 3429 sr 33600 bps
14 V34 2800 sr 14400 bps 35 V34 3200 sr 14400 bps 56 ANSam
15 V34 2800 sr 16800 bps 36 V34 3200 sr 16800 bps 57 CM
16 V34 2800 sr 19200 bps 37 V34 3200 sr 19200 bps 58 JM
17 V34 2800 sr 21600 bps 38 V34 3200 sr 21600 bps 59 INFO0c & TONEB
18 V34 2800 sr 24000 bps 39 V34 3200 sr 24000 bps 60 INFO0c & TONEA
19 V34 2800 sr 26400 bps 40 V34 3200 sr 26400 bps 61 PPh & AC & ALT
20 V34 3000 sr 4800 bps 41 V34 3200 sr 28800 bps
21 V34 3000 sr 7200 bps 42 V34 3200 sr 31200 bps
422
5.2.5. Service Mode 6 (RAM Initialization)
Initializes RAM and restores the Function Parameters to their default values.
Note:
This operation should be performed when the unit is first installed.
For DP-2000
Step Operation or Unit Condition LCD Display
1 Standby NOV-15-2000 15:00
00%
For DP-2500/3000
Step Operation or Unit Condition LCD Display
1 Standby NOV-15-2000 15:00 00%
READY TO FAX
3 Press “MONITOR” four times, then press “*”. SERVICE MODE (1-9)
ENTER NO.
7 Return to step 3 and press “STOP” to return to standby. NOV-15-2000 15:00 00%
READY TO FAX
423
RAM Initialization Table
No. Initialize Mode Description
99 SHIPMENT SET (A) Deletes all setting information, except parameter number
80 and 81, then set default values.
98 SHIPMENT SET (B) Deletes all setting information, except parameter number
61, 80 and 81, then set default values.
97 FLASH MEMORY CLEAR Deletes all information in the Flash Memory.
1# MANUFACTURE SET Factory use only. DO NOT USE IN THE FIELD.
16 LBP ERROR LOG CLEAR Clears the Printer Error Log.
15 LOGO/ID/PSWD CLEAR Clears the Logo, ID, Polling Password.
14 ALL JOB CLEAR Clears all Jobs stored in Flash Memory.
13 PROGRAM DIAL CLEAR Clears the Program keys.
12 AUTO DIAL CLEAR Clears the One-touch, ABBR Numbers and Phone Books.
11 JOURNAL CLEAR Clears the Journal contents.
* PARAMETER INITIALIZE Restores the Fax and Function Parameters to default
values.
424
5.2.6. Service Mode 8 (Check & Call)
5.2.6.1. Overview
This feature enables the Authorized Servicing Dealers to manage and improve the machine maintenance to
their customers by alerting them of equipment problems. It also can be used as a Supply Sales Tool by
alerting the Dealer that the unit is running Low on Toner. The function overview is as follows:
1. The machine’s printer error information is stored in the Printer Report.
2. The printer report can be manually printed when required.
3. When printer errors occurs, the unit can automatically transmit the Service Alert Report to the pre-
registered telephone number or email address.
4. When the unit detects Low Toner or PM counter reached the maintenance timing, it can automatically
transmit the Maintenance Alert Report to the pre-registered telephone number or email address.
5. When the unit detects Low Toner, it can automatically print out the Toner Order Form with pre-
registered order information.
Printer
Info. Tx
Error Log Only Content of Error
Code Report
Code
E1-20 22 O O Laser unit horizontal synchronization error.
E1-22 20 O O Polygon motor does not reach to constant speed within
specified time.
21 O O Polygon motor does not rotate constantly.
E3-20 41 O O Main motor (DC motor) rotation error.
E4-01 10 O O Fuser temperature does not increase even heater on.
11 O O Fuser temperature does not decrease even heater off.
12 O O Overshoot or undershoot occurred.
13 O O Thermistor open.
14 O O Detect overheat.
E4-10 30 O O Exhaust fan motor (1) does not rotate.
425
Printer
Info. Tx
Error Log Only Content of Error
Code Report
Code
E5-11 40 O O Fuser Thermistor and Toner sensor error.
E5-12 - O O Main CPU/LPC interface error.
E5-22 51 O O Finisher/LPC unit interface error.
E7-10 - O O Sub CPU System error.
E7-11 - O O Scanning abnormal from Platen Glass.
E7-12 - O O Xenon Lamp is Disconnected.
E7-20 - O O Finisher Paper Exit Motor.
E7-21 - O O Finisher Paper Exit Motor.
E7-22 - O O Finisher Tamper Motor.
E7-23 - O O Finisher Staple Motor.
E7-27 - O O Finisher Tray Shift Motor.
E7-28 - O O Finisher Bundle Process Motor.
E13 - Out of Toner.
J00 80 O Paper jam. Refer to the Jam Error Code Table for details.
J01 81 O
J02 82 O
J03 83 O
J04 84 O
J07 85 O
J08 86 O
J09 87 O
J12 89 O
J13 8A O
J14 8B O
J22 70 O
J23 71 O
J24 72 O
J30 88 O
J33 73 O
J34 B4 O
J40 8C O
J41 8D O
J42 74 O
J45 8E O
J46 8F O
J47 75 O
J50 A0 O
J51 A1 O
J52 A2 O
J53 A3 O
J55 A4 O
J55 A8 O
J56 A5 O
J56 A9 O
J57 A6 O
426
Printer
Info. Tx
Error Log Only Content of Error
Code Report
Code
J57 AA O Paper jam. Refer to the Jam Error Code Table for details.
J58 A7 O
J58 AB O
J59 76 O
J59 77 O
J59 78 O
J59 79 O
J60 C0 O
J61 C5 O
J62 C1 O
J63 C2 O
J64 C3 O
J65 C4 O
J66 C6 O
J67 C7 O
J80 B0 O
J81 B1 O
J82 B2 O
J83 B3 O
J84 B5 O
J85 B6 O
J86 B7 O
J87 B8 O
J88 7A O
J89 7B O
J89 7C O
J89 7D O
J90 90 O
J91 91 O
U1 61 Front Cover Open.
U1 62 Right Cover Open.
U13 60 No Toner Cartridge is installed.
U13 X Low Toner
U6 66 1st Feed Cover Open.
U6 67 2nd Feed Cover Open.
U6 68 3rd Feed Cover Open.
U6 69 4th Feed Cover Open.
U6 6A Paper Transport Unit Open.
Note:
1. Transmission Report: o = Service Alert Report, x = Maintenance Alert Report
2. Condition: R = Receive Mode, C = Copy Mode, S = Standby Mode, T = Transmit Mode
427
5.2.6.3. Setting Operation
For DP-2000
8:CHECK & CALL
PRESS SET TO SELECT
SET or START
INTERNET
1 SET or START
CHECK & CALL (1-9) SERVICE ALERT FAX # SERVICE ALERT MAIL #
CLEAR 1:SVC. ALERT FAX # CLEAR
OK OK
Enter a destination fax number (Max. 36 digits) or an email
address (Max. 60 characters) for the Service Alert Report.
When it is entered, the automatic transmission of the Service
Alert Report becomes effective.
INTERNET
2 SET or START
CHECK & CALL (1-9) MAINT. ALERT FAX # MAINT. ALERT MAIL #
CLEAR 2:MAINT. ALERT FAX # CLEAR
OK OK
Enter a destination fax number (Max. 36 digits) or an email
address (Max. 60 characters) for the Maintenance Alert
Report. When it is entered, the automatic transmission of the
Maintenance Alert Report becomes effective.
3 SET or START
CHECK & CALL (1-9) TONER ORDER FAX #
CLEAR 3:TONER ORDER FAX # CLEAR
OK
Enter the supply fax number to be printed on the Toner Order
Form. When it is entered, the automatic printing of the Toner
Order Form becomes effective.
Max. 36 digits (i.e. 201 111 4444)
4 SET or START
CHECK & CALL (1-9) TONER ORDER TEL #
CLEAR 4:TONER ORDER TEL # CLEAR
OK
Enter the supply telephone number to be printed on the Toner
Order Form.
Max. 36 digits (i.e. 201 111 5555)
5 SET or START
CHECK & CALL (1-9) DEALER NAME
CLEAR 5:DEALER NAME CLEAR
OK
Enter the Dealer's Name to be printed on the Toner Order
Form.
Max. 25 digits (i.e. Panafax Corp.)
6 SET or START
CHECK & CALL (1-9) CUSTOMER ID
CLEAR 6:CUSTOMER ID CLEAR
OK
Enter a Customer ID code to be printed on the Service Alert
Report, Maintenance Alert Report and Toner Order Form.
Max. 16 characters (i.e. ABC Company)
7 SET or START
CHECK & CALL (1-9) PRINTER REP. XMT:Off
CLEAR 7:PRINTER REPORT XMT 1:OFF 2:ON
1 and SET 2 and SET
* DIALING *
8 555 1234
SET or START CALL DATE AND TIME
CHECK & CALL (1-9)
CLEAR 1:MONTHLY 2:PERIOD After the Service Alert Report is transmitted
8:CALL DATE AND TIME to the pre-registered FAX # or Email Address,
the machine returns to standby mode.
1 and SET 2 and SET
Set the date, hour and minute for every Set the date interval and the hour and minute
month to activate automatic transmission of the to activate automatic transmission of the
Maintenance Alert Report to the registered Maintenance Alert Report to the registered
Service Alert Fax/Mail #. Service Alert Fax/Mail #.
9
CHECK & CALL (1-9) SET or START PM COUNT:OFF
CLEAR 9:PM COUNT 1:OFF 2:ON
2 and SET
Set to activate automatic transmission of
the Maintenance Alert Report to the registered Maint.
Alert Fax/Mail # if the machine reaches the PM Count.
428
For DP-2500/3000
SERVICE MODE (1-9)
8:CHECK & CALL
PRESS SET TO SELECT
SET or START
INTERNET
1 SET or START
SERVICE MODE SERVICE MODE SERVICE MODE
CLEAR CHECK & CALL
SERVICE MODE (1-9)
(1-9) CLEAR SERVICE ALERT FAX # SERVICE ALERT MAIL #
1:SVC. ALERT FAX # ENTER TEL.NO. AUTO ENTER EMAIL ADDRESS
OK OK
Enter a destination fax number (Max. 36 digits) or an email
address (Max. 60 characters) for the Service Alert Report.
When it is entered, the automatic transmission of the Service
Alert Report becomes effective.
INTERNET
2 SET or START
SERVICE MODE SERVICE MODE SERVICE MODE
CLEAR CHECK & CALL (1-9) CLEAR MAINT. ALERT FAX # MAINT. ALERT MAIL #
2:MAINT. ALERT FAX # ENTER TEL.NO. AUTO ENTER EMAIL ADDRESS
OK OK
Enter a destination fax number (Max. 36 digits) or an email
address (Max. 60 characters) for the Maintenance Alert
Report. When it is entered, the automatic transmission of the
Maintenance Alert Report becomes effective.
3 SET or START
SERVICE MODE SERVICE MODE
CLEAR CHECK & CALL (1-9) CLEAR TONER ORDER FAX #
3:TONER ORDER FAX # ENTER TEL.NO. AUTO
OK
Enter the supply fax number to be printed on the Toner Order
Form. When it is entered, the automatic printing of the Toner
Order Form becomes effective.
Max. 36 digits (i.e. 201 111 4444)
4 SET or START
SERVICE MODE SERVICE MODE
CLEAR CHECK & CALL (1-9) CLEAR TONER ORDER TEL #
4:TONER ORDER TEL # ENTER TEL.NO. AUTO
OK
Enter the supply telephone number to be printed on the Toner
Order Form.
Max. 36 digits (i.e. 201 111 5555)
5 SET or START
SERVICE MODE SERVICE MODE
CLEAR CHECK & CALL (1-8) CLEAR DEALER NAME
5:DEALER NAME
OK
Enter the Dealer's Name to be printed on the Toner Order
Form.
Max. 25 digits (i.e. Panafax Corp.)
6 SET or START
SERVICE MODE SERVICE MODE
CLEAR CHECK & CALL (1-9) CLEAR CUSTOMER ID
6:CUSTOMER ID
OK
Enter a Customer ID code to be printed on the Service Alert
Report, Maintenance Alert Report and Toner Order Form.
Max. 16 characters (i.e. ABC Company)
7 SET or START
SERVICE MODE SERVICE MODE
CLEAR CHECK & CALL (1-9) PRINTER REP. XMT:Off
7:PRINTER REPORT XMT 1:OFF 2:ON
1 and SET 2 and SET
NOV-15-2000 15:00
* DIALING *
8 555 1234
SERVICE MODE
SET or START CALL DATE AND TIME
SERVICE MODE
CLEAR 1.MONTHLY 2.PERIOD After the Service Alert Report is transmitted
CHECK & CALL (1-9) to the pre-registered FAX # or Email Address,
8:CALL DATE AND TIME the machine returns to standby mode.
1 and SET 2 and SET
Set the date, hour and minute for every Set the date interval and the hour and minute
month to activate automatic transmission of the to activate automatic transmission of the
Maintenance Alert Report to the registered Maintenance Alert Report to the registered
Service Alert Fax/Mail #. Service Alert Fax/Mail #.
9
SERVICE MODE SET or START SERVICE MODE
CLEAR PM COUNT:OFF
CHECK & CALL (1-9)
1:OFF 2:ON
9:PM COUNT
2 and SET
Set to activate automatic transmission of
the Maintenance Alert Report to the registered Maint.
Alert Fax/Mail # if the machine reaches the PM Count.
429
Note
1. Service Alert Report
To enable the automatic transmission of Service Alert Report, enter the destination fax telephone
number or the email address in the “SERVICE ALERT (FAX # or MAIL #)" field. When a printer error
occurs, the Service Alert Report is transmitted to the designated number automatically. A blank entry in
this field, disables the Automatic transmission of the Service Alert Report.
2. Maintenance Alert Report
To enable the automatic transmission of Maintenance Alert Report, enter the destination fax telephone
number or the email address in the “"MAINT. ALERT (FAX # or MAIL #)" field. When a printer error
occurs, the Maintenance Alert Report is transmitted to the designated number automatically. A blank
entry in this field, disables the Automatic transmission of the Maintenance Alert Report.
3. Toner Order Form
To enable the automatic printout of the Toner Order Form, enter the destination fax telephone numbers
in the “Toner Order FAX #” field. When a low toner error occurs, the Toner Order Form is printed
automatically. A blank entry in this field, disables the automatic printout of the Toner Order Form.
4. SERVICE ALERT FAX #, this would be the fax telephone number for the Dealer's Service Department.
SERVICE ALERT MAIL #, this would be the email address for the Dealer's Service Department.
MAINT. ALERT FAX #, this could be the fax telephone number for the Dealer's Supply Sales Desk.
MAINT. ALERT MAIL #, this could be the email address for the Dealer's Supply Sales Desk.
TONER ORDER FAX #, this could be the fax telephone number for the Dealer's Supply Sales Desk.
TONER ORDER TEL #, this could be the voice telephone number for the Dealer's Supply Sales Desk.
DEALER NAME, this name is printed on the Toner Order Form.
CUSTOMER ID, to identify your customer, enter up to 16 characters user code in this field. This name
will be printed on the Service Alert Report, Maintenance Alert Report and Toner Order Form.
430
5.2.6.4. SERVICE ALERT REPORT FORMAT
****************************
> SERVICE ALERT REPORT <
****************************
LAST PRINT ERROR : NOV-15-2000 18:30 E03-20 41 00-00000835
(1) CUSTOMER ID : ABC COMPANY
(2) FIRMWARE VERSION
HOST : DP-2500 AAV11000PU
CONTROL PANEL : 10300
PRINTER : 400046
(3) COUNTER INFORMATION:
F7-02 PM CYCLE CURRENT
TOTAL COUNT 000835
PM COUNT (150000) 000835
SCANNER PM COUNT (240000) 000401
ADF/iADF PM COUNT (------) 000326
OPC DRUM COUNT 30000 000835
PROCESS UNIT COUNT 120000 000835
PAPER TRANSPORT COUNT (See Note)
ADU COUNT (See Note)
DUAL-PATH COUNT (See Note)
F7-03 F7-05
SHEET BYPASS COUNT : 000249 COPY PRINT COUNT : 000575
1st PAPER TRAY COUNT : 000006 COPY SCAN COUNT : 000065
2nd PAPER TRAY COUNT : 000391 F7-06
3rd PAPER TRAY COUNT : 000000 PC PRINT COUNT : 000000
4th PAPER TRAY COUNT : 000000 PC SCAN COUNT : 000000
F7-04 F7-08
ADF/iADF COUNT : 000326 FAX TRANSMIT COUNT : 000240
ADF/iADF READ COUNT : 000320 FAX RECEIVE COUNT : 000082
(4) SCANNER COUNT : 000401 FAX PRINT COUNT : 000077
SCANNER READ COUNT : 000198
PRINT ERROR:
NO. DATE & TIME ERROR CODE ERROR COUNT | NO. DATE & TIME ERROR CODE ERROR COUNT
-------------------------------------------------------------------------------------------
01 NOV-15-2000 18:30 E03-20 41 00-00000835 | 16 NOV-05-2000 18:30 E04-10 30 00-00000830
" | "
" | "
" | "
" | "
" | "
" | "
" | "
" | "
" | "
" | "
" | "
" | "
15 NOV-05-2000 12:30 J02 00-00000155 | 30 NOV-04-2000 11:30 J71 02-00000298
-LOGO PANASONIC -
************************************ -CHARACTER ID - ***** -31415926535897932384-***********
Explanation of Contents
(1) Customer ID
(2) Firmware Version
(3) Counter Information
(4) Print Error Last 30 records (Latest on top)
Note:
Available with Host Firmware version 2.xxxx or higher.
431
5.2.6.5. MAINTENANCE ALERT REPORT FORMAT
****************************
> MAINTENANCE ALERT REPORT <
****************************
-LOGO PANASONIC -
Explanation of Contents
(1) Low Toner Message (Fixed) “MACHINE IS RUNNING OUT OF TONER”
(2) Customer ID Up to 16 characters (User Identification Code)
(3) Firmware Version
(4) Transmission / Reception / Copy / Print Counters
432
*************************************
> TONER CARTRIDGE ORDER FORM <
*************************************
**** The toner supply in your machine is running low **** (1)
To order a replacement Cartridge from your Authorized Dealer
Attention: Attention:
Quantity Required:
/ /
Print your name and title Signature & Date
Explanation of Contents
(1) Low Toner Message (Fixed) “The toner supply in your machine is running low”
(2) Dealer Name Up to 25 digits
(3) Toner Order Tel # Up to 36 digits
(4) Toner Order Fax # Up to 36 digits
(5) Customer ID Up to 16 characters (User Identification Code)
(6) Toner Cartridge No. DQ-TU18B
433
5.2.7. Service Mode 9 (System Maintenance)
5.2.7.1. Overview
This Service Mode is used to maintain and/or update the firmware of the machine. Use the following
procedure for System Maintenance.
For DP-2000
5 Press “START” to view the current firmware, and press SYSTEM MAINT. (1-8)
"START" again to update it. 2:FIRMWARE BACKUP
To perform other maintenance task, enter a No. or use
“V” or “/\ “ to scroll to the desired task.
Ex: Enter “2”.
6 Press “START” and “SET”. FIRMWARE BACKUP
* IN PROGRESS *
434
For DP-2500/3000
3 Press “MONITOR” four times, then press “*”. SERVICE MODE (1-9)
ENTER NO.
7 After the backup is completed, repeat step 5 through 6 SERVICE MODE (1-9)
to request another operation. ENTER NO.
435
5.2.7.2. Operation
For DP-2000
9:SYSTEM MAINTENANCE
PRESS SET TO SELECT
SET
or
START
1 2
After Uploading
3 SETor START
SYSTEM MAINT.(1-8) PARAMETER RESTORE SETor START PARAMETER RESTORE
CLEAR 3:PARAMETER RESTORE CLEAR PRESS SET TO START * IN PROGRESS *
After Downloading
4 SETor START
SYSTEM MAINT.(1-8) PARAMETER BACKUP SETor START PARAMETER BACKUP
CLEAR 4:PARAMETER BACKUP CLEAR PRESS SET TO START * IN PROGRESS *
After Uploading
After Erasing
After Downloading
STOP
436
For DP-2500/3000
SERVICE MODE (1-9)
9:SYSTEM MAINTENANCE
PRESS SET TO SELECT
SET
or
START 1 2
INVOICE/A5
LETTER-R/A4 Display card version *
1 SERVICE MODE SET or START SERVICE MODE SERVICE MODE
SYSTEM MAINT. (1-8) DP-XXXXAAV12300PU SETor START FIRMWARE UPDATE
CLEAR 1:FIRMWARE UPDATE CLEAR PRESS SET TO START * IN PROGRESS *
After Downloading
INVOICE/A5 LETTER-R/A4
4 SETor START
SERVICE MODE SERVICE MODE SERVICE MODE
SETor START
CLEAR SYSTEM MAINT. (1-8) CLEAR PARAMETER BACKUP PARAMETER BACKUP
4:PARAMETER BACKUP PRESS SET TO START * IN PROGRESS *
After Uploading
INVOICE/A5
LETTER-R/A4
Display 1.5sec SERVICE MODE
PARAMETER BACKUP
* COMPLETED *
After Erasing
INVOICE/A5 LETTER-R/A4
After Downloading
8
1
SERVICE MODE 2 Displays card version SERVICE MODE
CLEAR SYSTEM MAINT. (1-8) Refer to the Sect. 5.9.4 until STOP is pressed. DP-XXXXAAV12300PU
8:SEND RCV'D FILE * COMPLETED *
INVOICE/A5 STOP
LETTER-R/A4
1 2
Service Mode default display
437
5.2.7.3. Send Received File
This function is the relief mode which makes it possible to retrieve memory received documents during a
fatal printer error by transferring the documents to another fax machine.
For DP-2000
NOV-15-2000 15:00
00%
FUNC 7 MON X 4 *
SERVICE MODE
ENTER NO. OR v
9 8
CLR Pi-pi-pi
SYSTEM MAINT.(1-8) FILE DOES NOT EXIST
8:SEND RCV FAX
SET or START
CLR
ENTER STATION(S)
THEN PRESS START
Enter station
CLR
CLR
<02> LONDON OFFICE START
011 44 123 4567
SET
CLR
* DIALING * NO.nnn
212 555 1234
438
For DP-2500/3000
NOV-15-2000 15:00 00%
READY TO FAX
FUNC MON x 4 *
9 8
CLR Pi-pi-pi
SET or START
CLR
NOV-15-2000 15:00
READY TO FAX
ORIGINAL SET
Enter station
CLR
CLR
SET
CLR
START 1. After the received document file is successfully transmitted, unit will
SET
NOT delete the file automatically.
2. Under certain conditions there could be two (2) received files stored
separately. In this case, transmission will be made separately.
3. Only normal received document will be transmitted.
NOV-15-2000 15:00 00%
READY TO FAX
439
6 System Description
6.1. Mechanical Operation
6.1.1. Scanning Mechanism (Flatbed)
1. Scanning Mechanism
The Scanning Mechanism consisting of Lens, CCD PCB Assy (207), Mirrors, Xenon Lamp (204), Lamp
Base Bracket (224) and Mirror 2 Bracket (233), is used to scan originals.
● The Mirror 1 (264) and Mirrors 2 (265) reflect image information, in the form of light, through the
Lens.
● The Lens focuses the image information and passes it to the CCD.
● The CCD, mounted on the CCD PC Board, converts the image information into an electrical signal.
● The Inner and Outer Timing Belts (202 & 203) driven by the Stepping Motor (201), move the Scanner
Assembly.
Mirror 1 (264)
Reflection Plate (231) Glass Assembly (557)
Xenon Lamp (204)
Outer Timing Belt (203)
Glass S (559)
Lamp Base Bracket (224) Inner Timing Belt (202)
Mirror 2 (265)
2. Transmit Mechanism
a. When ADF is used, originals are scanned on the Glass S (559). The Glass Assembly (557) is used
when scanning on the Platen.
b. The Scanning point is established by the Size Sensor 1 (270).
c. Document size is automatically set by the Original Size Sensor (1045) or manually set when the
Platen is used.
d. The Transmit Mechanism starts feeding and scanning originals based on the above Document Size
Setting.
e. When scanning is completed, the Stepping Motor (201) stops rotating and the Lamp Base and
Mirror 2 Brackets (224 & 233) return to the standby position.
440
During scanning, the Lamp Base Bracket (224) and Mirror 2 Bracket (233) move in the direction of the
Black arrow and while returning to standby position, it moves in the direction of the White arrow as
shown in the illustration below. The location of these two brackets are established by the Size Sensor 1
(270) and the scanning length is established by the setting on the Touch Panel. The following illustrates
the Drive system.
441
6.2. Automatic Document Feeder
The ADF (Automatic Document Feeder) automatically feeds paper into the unit, one original at a time. Its
main features are:
1. Place originals Face-Up
2. Correct Order Stacking (Collation Mode)
3. Paper Feed Mechanism with Pre-Feed Roller
4. Oversized Feed 2 Roller for stable scanning
442
5. Final Operation
After ejecting the last original on the ADF, the Clutch reverses the direction of rotation raising the
Document Stopper to its standby position.
edger)
Automatic Document Feeder
LS1, 2)
(L
)
)
420 (A3
NVOICE
431.8
364 (B4
-R)
330.2 (F
- R)
Separation Document
297 (A4
Roller ADF Roller Stopper Pre-Feed Roller
257 (B5
Original Detection
)
(I
(1737)
210 (A5
(1740) (1728) (1731) Sensor (1045)
.9
38
215
Exit Roller
(3505)
Read Point
Sensor(1045)
Exit Roller (1751)
Eject Sensor
(1045) Stamp Head (1636)
Feed 2 Roller
(1753)
443
6.2.2. Inverting Automatic Document Feeder
The i-ADF automatically inverts two-sided original(s) for faxing or copying of the second side. This feature
enables machines with a duplexer mounted to perform duplex copying.
An i-ADF (Inverting Automatic Document Feeder) functions in a similar manner as the ADF (Automatic
Document Feeder), with the main exception being the document eject path after scanning. The following is
the description of the main differences.
4. Sub Tray
The Inverting ADF system includes a Sub Tray (1617), which supports the originals during the ejection
mode of the double-side scanning operation.
The Release Lever Plate (1735) grasps the originals and prevents them from being ejected into the
Sub Tray.
444
edger)
Inverting Automatic Document Feeder
LS1.2)
Pre-Feed Roller
(L
)
420 (A3
(1731)
.8
)
)
364 (B4
Roller
-R
1
Original Detection Sensor (1045)
330.2 (F
)
43
(1740) Document
-R
297 (A4
Stopper Pinch Roller (1627)
257 (B5
Pinch Roller ADF Roller
215.9 (IN
)
(1838) (1728) (1737)
(Feed Skew Adjustment) Release Lever 38
Plate (1735)
Exit Roller
(3505)
Read Point
Sensor (1045)
Feed 2 Roller
(1753) Read Point Stamp Head (1636)
Reversing 1 Guide (1752)
Pinch Roller Pinch Roller (1838)
(1838) (Reverse Registration or Feed Skew Adjustment)
(Registration Adjustment)
445
6.3. Receive Mechanism
6.3.1. Paper Feed Modules
1. Paper Feed Module No. 1 (Std), 2, 3 and 4
< NP Sensor Operation >
NP Actuator (1133)
NP Sensor (1045)
a. The NP Actuators (1133) attached to the Paper Feed Blocks No.1, 2, 3 and 4 determine if there is
paper in the paper tray.
b. The paper in the paper tray lifts up the NP Actuator, allowing the light from the LED to actuate the
NP Sensor (1045).
446
< Paper Feed Module Operation >
Clutch (1260)
Registration Actuator (1120)
a. When the printing operation begins, the Printer Motor (901) starts driving the Gears.
b. The Clutch (1260) is energized for a specified period of time and turns ON. This activates the Paper
Feed Roller (1144). The paper is separated into individual sheets by the C25 Gear Roller (1145) and
is transported.
c. The paper is transported to the Registration Roller (1121), activating the Registration Sensor (1045).
After a specified period of time, the Clutch (1260) is turned ON and the Registration Roller (1121)
and the Registration Pinch Roller start rotating. The paper is transported to the OPC drum area.
d. The paper passes through the Read Point Sensor (1045) and after a specified period of time, the
Clutch (1260) is turned OFF. The Registration Roller and the Registration Pinch Roller stop rotating.
447
< Paper Feed Module (Optional) Operation >
Clutch (1260)
Actuator 2 (3104)
Motor
(3115)
C25 Gear Roller
(1145)
a. When the printing operation begins, the Printer Motor (901) and the Motor (3115) start driving the
Gears.
b. The Clutch (1260) is energized for a specified period of time and turns ON. This activates the Paper
Feed Roller (1144). The paper is separated into individual sheets by the C25 Gear Roller (1145) and
transported by the Intermediate Roller (3106).
c. The paper is transported to the Registration Roller (1121), activating the Registration Sensor (1045).
After a specified period of time, the Clutch (1260) is turned ON and the Registration Roller (1121)
starts rotating. The paper is transported to the OPC drum area.
d. The paper passes through the Read Point Sensor (1045) and after a specified period of time, the
Clutch (1260) is turned OFF. The Registration Roller and the Registration Pinch Roller stop rotating.
448
< Paper Feed Module Lift up Mechanism >
NP Sensor (1045)
a. When inserting the Paper Tray into the machine, the NP Sensor (1045) activates. At the same time,
the Lift Plate (809) is combined with the coupling which drives the Lift Plate of the machine. The Lift
Plate rotates, lifting the Bottom Plate (808) and the Recording Paper.
b. Once the Bottom Plate and the Recording Paper are raised, the NP Sensor (1045) is turned ON.
The Lift DC Motor (1152) stops rotating, maintainig the recording paper at the certain level.
449
< Paper Feed Module Recording Paper Size Setting >
Coupling (1171)
Lift DC Motor (1152) NP Sensor (1045)
a. The Recording Paper size in the Paper Feed Module is set on the Touch Panel.
450
2. Sheet Bypass
< NP Sensor Operation >
a. The NP Actuator attached to the Paper Feed Unit determines if there is paper in the paper tray.
b. The paper in the paper tray lowers the NP Actuator and the NP Sensor (1045) actuates.
a. When the printing operation begins, the PRINT (Print Request Signal) turns On and the Printer
Motor (901) starts driving the Gears.
b. The Clutch (1260) is energized for a specified period of time and turns ON. This activates the Paper
Feed Roller (1144). The paper is raised by the Pressure Plate (1237) and transported to the
Separator Holder Pad (1242). The paper is separated into individual sheets by the Separator Holder
(1209).
c. The paper is transported to the Registration Roller (1121), activating the Registration Sensor (1045).
d. After a specified period of time, the Clutch (1260) is turned ON and the Registration Roller (1121)
and the Registration Pinch Roller start rotating. The paper is transported to the OPC drum area.
After lowering the Pressure Plate (1237) during the specified period of time, the Clutch is turned
OFF and the Paper Feed Roller (1144) stops rotating.
e. After the trailing edge of the paper passes the Registration Sensor (1045) and after a specified
period of time, the Clutch (1260) is turned OFF. The Registration Roller and the Registration Pinch
Roller stop rotating.
451
6.3.2. Printing Process Operation
The Printing Process Operation consists of Process Unit and Toner Cartridge with Toner supplied. The
Toner Paddles in the Toner Cartridge attach to the Process Unit by means of gears, the Toner Cartridge
Shutter opens and Toner is supplied to the Process Unit using gravity.
The Process Unit includes the Waste Toner Paddle and Mag Roller (769) that supplies Toner to the OPC
Drum (718).
The Cleaning Blade (717) is attached to the OPC Unit. The Cleaning Blade scrapes the OPC Drum surface
to remove the excess toner on the surface of the OPC Drum into the Waste Toner Chamber. The removed
toner is moved into the Waste Toner Bottle by means of Waste Toner Paddle and Waste Toner Drive.
OPC Unit
Waste Toner Paddle
Waste Toner
Drive Waste Toner
Toner Cartridge
OPC Shutter
Cleaning Blade (717)
Bias Charge
Roller (703)
Recording
Paper
Handle
Bias Transfer
Roller (1221)
Toner Cartridge
Charge
In the dark, the Bias Charge Roller (703) applies a high, uniform negative charge to the surface of the
OPC Drum. The surface potential is approximately -560 VDC and remains because the drum has a high
electric resistance in the dark.
Exposure
A portion of the laser beam is deflected to the timing sensor [Beam Detection (BD) Sensor], which
controls the start timing of scanning on the OPC Drum. The CPU also uses the timing sensor to detect
abnormal signals. The light beam from the laser diode is modulated by the digital signal and converted to
parallel light waves by the collimator lens. The beam is then directed to the rotating polygon mirror,
where it is reflected to the f-q lens and then focused onto the OPC Drum surface. The laser beam moves
across the surface of the OPC Drum in the scanning direction. Where the laser beam is applied, the
negative charge on the drum dissipates, and where the laser is not applied, the negative charge
remains. This action forms a latent, electrostatic image on the OPC Drum, corresponding to the original
image.
452
Development
This development process uses a conventional method, where toner coats a Development Roller and
transfers to the latent image on the OPC Drum. In the Toner Cartridge, the (mono-component) toner is
negatively charged by the friction between the rotating Development Roller (Mag Roller) (769) and the Dr
Blade (762). This combination and the rotation of the Mixing Blade transfers the toner from the reservoir
and forms a brush effect on the Mag roller. Where the magnetic brush lightly touches the OPC Drum, the
negatively charged toner is attracted to the latent image on the drum, forming a mirror image of the
original on the drum. Any remaining toner is removed from the Mag Roller by the Dr Blade and is
recycled back into the toner
reservoir. A bias voltage of approximately 1.65 kVACp-p at 1.7 kHz, riding on a -430 VDC bias is applied
to the magnetic brush to achieve maximum print quality.
Cleaning
After transfer, some toner may remain on the surface of the OPC Drum. A Cleaning Blade (717) scrapes
the OPC Drum surface, and the removed toner is moved into the Toner Waste Box, outside the Toner
Cartridge.
453
6.3.3. Laser Unit
LSU
Lens LSU Chassis
Polygon Mirror /
Polygon Motor
Collimator Lens
Aperture
Collimator Lens
Laser
Beam Detection
Reflection Mirror Beam Detection Beam Detection Sensor
Lens
1. Laser
This Laser uses the semiconductor laser. The beam power on the drum surface is approximately 0.25
mW.
2. Collimator Lens
This lens converges and focuses the laser beam, converting it to parallel light.
3. Aperture
This controls the size of the laser beam.
4. Polygon Mirror and Polygon Motor
The polygon scanner consists of a 6-sided mirror, directly driven by a DC motor, revolving at 42,000
rpm. The laser beam is reflected against these mirrors and swept over the recorded width in the
scanning direction.
5. Beam Detection (BD) Lens and Beam Detection (BD) Sensor
The BD Lens receives the reflected light from the Polygon Mirror and redirects it into the BD Sensor,
which converts the laser beam into electrical signals and sets the start timing for the scanning line.
6. F-q Lens
This amorphous plastic, molded lens is designed to provide parallel laser light across the surface of the
drum, providing a constant scanning speed.
7. Lens
This corrects the skew of each side on the Polygon Mirror.
454
6.3.4. Fuser Operation
The paper passes through the Fuser Roller (1026) and is subjected to heat and pressure in the Fuser Unit.
Pressure between the Fuser Roller (1026) and Pressure Roller (1027) fuses or bonds the toner into the
paper.
Separation (1047)
Recording Paper
Thermostat (1038)
455
Separator (1047)
Six Separators (1047) are installed in the Fuser Roller (1026). This prevents the recording paper from
wrapping around the Fuser Roller (1026), causing a paper jam.
When the Fuser Unit does not reach the specified temperature within a certain period of time, an Error code
is shown on the display, stopping the operation.
When the Thermistor Assembly (1041, 1042) is disconnected or the surface temperature of the Fuser Roller
(1026) is out of limit, an Error code is shown on the display, stopping the operation.
456
DP-2000/2500/3000
6.4.
6.4.1.
Block Diagram
(DP-3000)
7.16MHz (DP-2500/3000) (DP-2000)
CONS (19158) 3V SYSTEM BUS S C (1983) PNL1 (19120) PNL4 (19120)
CCD (207) CPU RTC
(uPD3747) AFE Super PYXION CPU Bz
LVDS 14.32MHz SH7041
MN86076 SH7041 Bz
Key CPU
3V/(2.5V) S-DRAM S-DRAM Matrix Key
Matrix
Open Sensor 16MHz 16MB 2MB Touch Panel
BOOK
Angle Sensor Controller
SOCKET
Size Sensor 1 DC-DC LCD UNIT
F-ROM 20 x 2
Stepping Motor MOTOR Inverter CHARACTER
DRIVER S-DRAM EDO-DRAM (2MB)PROGRAM LCD UNIT
Size Sensor 1 8MB x 2 2MB x 1 320 x 240 dot
Size Sensor 3 IMAGE BUS LCD Controller
Sensor
M16C/62 240pin FXB (1985)
MOTOR IMAGE
ADF Motor DRIVER MEMORY
3V/5V AFE LCU (1995)
Solenoid DRIVER SORT F-ROM
PDL DP-2000:option (2MB) LCE (1994)
Option C
40.4720MHz CODEC AD,DA
SCN O
CONNECTOR (PM-22c) SGCP
N
(19114) 35.97514MHz N
Original Width Sensor SNS OPTION MODEM
E Reset HANDSET
S-DRAM CONNECTOR
36.74298MHz C IC
8, 16 or 128MB
T
O SOCKET
BRIDGE
R DZAC000233 S-DRAM
8MB
5V SYSTEM BUS
1-Bin Finisher FLASH CARD
Electrical Circuit Explanation
CONNECTOR
F-ROM CARD
Sensor
MOTOR SCI +5V
Motor DRIVER CPU KEY API
COUNTER DZZSP58025 +3.3V/+2.5V POWER PRINTER I/F
OPTION
CONNECTOR
+24V CONTROL
457
PWM
CIRCUIT LCU (1995)
-12V G3B LCE (1994)
2Way Exit Guide Unit
+5Vp
OPTION
CONNECTOR
+5V
-12V
+24V
+24V
FAN
+5VP
PCNT
Sensor
Clutch API
DZZSP58025 DRIVER LVPS (1999)
MOTOR
DRIVER Thermistor
550 sheets Paper Feed Unit (2nd) Fuser Lamp HTC
Sensor PCB
Clutch DRIVER LP (1997) Thermistor (273)
Sensor Motor Thermistor (280)
550 sheets Paper Feed Unit (3rd) Thermal Fuse RLB PCB
Paper Feed Unit Sensor (19127)
Sensor Sensor Printer Motor
MOTOR
Motor DRIVER Clutch Clutch
MOTOR Thermostat HTC2 AC SW (447)
Lift DC Motor DRIVER CPU PCB
Clutch DRIVER (1998) AC
Fuser Lamp AC INLET (444)
550 sheets Paper Feed Unit (4th)
LSU SC :System Controller
Sensor THERMISTOR AFE :Analog Front End
(1124) SCN :Scan Controller PWM :Pules Wide Modulation
Clutch DRIVER HEAT LAMP LPC :LP Controller MSC :Main System Controller OPTION
DANCE :Document Adapter for New Copier Engine
6.4.2. Fax System Control Circuit
The System Control Block consists of the following IC that control the general Fax functions.
Panel CPU
CPU SH2 DRAM 2MB
Scanning (IC1) (IC7)
Mechanism
Control CPU
F-ROM 2MB
D-BUS 3V
(IC12)
COPY
F-ROM 2MB PROGRAM
(IC11)
FAX PROGRAM
<+5V>
Analog
MN86076
FXB OPTION Front End
(IC51)
F-ROM 2MB (IC54,55)
(IC10)
MA-BUS 3V
Image Data
<+5V>
TR88017 MODEM
MN195004
(IC22)
(IC21)
API
IOD-BUS 5V
AL-BUS 5V
(IC14)
F-ROM SRAM
(IC19) (IC20) SODIMM
Image
Block OPTION
SORT OPTION Connector
SODIMM CN107
S-DRAM 8MB
OPTION
Connector (IC35) PRIF
OPTION
Connector
CN115,
CN113 116
CN120
BRIDGE
DZAC000233 PDL OPTION
(IC34) Connector
CN121
CODEC
PM-22c G3/I-NET
(IC33) OPTION
Connector
CN123
458
1. System CPU
The System CPU (SH7041) is a 32-bit RISC (Reduced Instruction Set Computer) type of CPU and
DMA Control, Serial Communication Port, Timer Control, Interrupt Control, DRAM Control, and I/O Port
are integrated into 1 chip. Mask ROM (64k byte) is already installed and it controls the Monitor, High
Speed managing Task and Boot Programming.
• DMA Control
It has a 4ch DMA Control and is used to transfer data between the following devices.
Communication CODEC (MN86064) ←→ Image Data Memory (DRAM)
• Serial Communication Port
It has a 2ch Serial Communication Port and is used to interface the following devices.
CPU ←→ Panel Unit (Panel CPU)
CPU ←→ Sub CPU for scanning (uPD78058)
• Timer Control
It is used to program the standard timer.
• Interrupt Control
It controls receipt & transfer to CPU the interrupt from MSC, Modem, LSI, Option, etc.
• DRAM Control
It generates DRAM Control Signal and Refresh Control when the power is ON.
• I/O Port
It is used to control lines and reset control around LSI.
3. System Memory
This system consists of the following memory.
• F-ROM (IC12) → F-ROM (2MB) for programming
• F-ROM (IC11) → F-ROM (2MB) for programming
The program is booted from F-ROM Card.
• F-ROM (IC10) → Image Data Memory (2MB)
During a blackout, the image data is backed up.
• DRAM (IC7) → Work RAM, buffer (2MB) for transfer and reception
459
6.4.3.
S-DRAM 2MB
(IC29)
S-DRAM 8MB SORT OPTION
(IC30)
SODIMM SODIMM
S-DRAM 8MB S-DRAM 8MB
OPTION OPTION
(IC31) (IC35)
Connector Connector
CN107 CN113
Image Data Circuit
BID-BUS 3V CODEC
CCD (207) MN86076 PM-22c
Analog (IC51) (IC33)
Front End
BRIDGE
(IC54,55)
DZAC000233
460
(IC34)
DANCE
PWM
and only coded data is transferred to the System Data BUS.
LD-BUS 3V
PDL OPTION
LPC (19129) 5 3V
Connector
CN121 CN121
461
• Synchronization Control Circuit
This circuit is used to synchronize the output of the recorded data with the horizontal synchronizing
output signal from the printer for each line. The IPC controls the resolution of the printer as follows.
Picture Edit/Recording Gate Array (DANCE) ←→ CODEC for Image (PM-22c) : Bus Selection
CODEC for Image (PM-22c) ←→ SORT Memory (S-DRAM) : Compress, Restore
SORT Memory (S-DRAM) ←→ System Memory (DRAM) : Communication
• S-DRAM Control
It generates S-DRAM Control Signal for SORT Memory and Refresh Control when the power is ON. it
does not backup the Page Memory.
462
6.4.4. Scanning Circuit
(For DP-2000/2500)
CCD (207)
uPD3747
(IC1)
(For DP-3000)
CCD (207) LVDS(IC5) CONS (19158) SC (1983)
LVDS(IC1) MN86076(IC51)
uPD3747
(IC3) Analog A/D Binary Binary Data
Enlargement
Reduction /
Correction
Master Converter Error (Copy,
Shading
(IC54) (IC55) Diffusion
Communication)
Gray Scale Gray Scale Data
Analog Front End
SCN (19114) CN2 CN103
(PC Scanner)
CN8
STEPPING
SLA7042M
MOTOR (IC2) Scanning Data
CN9 Signal Output
(To IC28)
LED LAMP Inverter
5 3V
M30620 CPU SH2
OPEN SENSOR
(IC1) (IC1)
3 5V
ANGLE SENSOR
Serial I/F
CN6
SIZE SENSOR 1
CN7
SIZE SENSOR 1
SIZE SENSOR 3
SIZE SENSOR 3
CN3
CN21
ADF (DZEP000473)
CN22 SLA7044M
ADF
MOTOR (IC1)
FEED 2 ROLLER
CLUTCH
ADF ROLLER CLUTCH TD62318
CN25
STAMP SOLENOID (IC5)
CN26
RELEASE LEVER
PLATE SOLENOID
ORIGINAL STOPPER
SOLENOID
TD62318
REVERSING 1 GUIDE
SOLENOID (IC4)
CN24
INVERTING ROLLER
CLUTCH
A3 WIDTH SENSOR
ORIGINAL LENGTH
SENSOR2
ORIGINAL LENGTH
SENSOR1
CN29
ADF COVER SENSOR
READ POINT SENSOR
1. Scanning LSI
MN86076 (IC51) is a Scanning LSI and generates Shading Correction, MTF Correction, Reduction/
Enlargement, and Gray Scale Error Diffusion. The Image Signal is converted to binary signal and
transported.
2. Scanning Mechanism Control CPU
M30620 is a 16 bit type of CPU that controls scanning mechanism. It controls TX Motor, Scanning
LED, Verification Stamp, Sensor Detection, and Solenoid Drive Control.
3. TX Motor Drive Circuit
TX Motor Drive Circuit is controlled by SLA7042M and SLA7044M (SCN PCB IC2, ADF PCB IC1).
463
6.4.5. Coding
Coding and decoding (MH/MR/MMR/JBIG conversion) is carried out by the hardware codec device. There
are 2 codecs, Image Codec and Communication Codec.
• PM-22c (IC33) : for Image Codec
It codes or decodes the data transferred from Sort memory. When copying, this codec codes from the
Image data to JBIG data. When communicating, this codec codes from Image data to MMR data.
• MN86064 (IC25) : for Communication Codec
This codec is used during TX/TR communication. When saving, this codec codes from the Image data
memory to MMR data.
464
6.4.7. Sleep Mode
Note:
When 10/100 Ethernet Interface / Internet Fax Kit is installed, the Sleep Mode is disabled.
This function reduces the power consumption in standby mode. During Sleep Mode, power is supplied only
to the Energy Saver Lamp to keep it at a steady ON condition, to the circuit that monitors incoming Ringing
signals and to circuits that maintain Deferred communications. The power is recovered only when an
incoming Ringing signal is detected, the time to perform a Deferred communication has lapsed or the
Energy Saver key is pressed.
465
6.4.8. Signal Routing
1. Copy
D-BUS +3V
CCD A/D MN86076
(Sort Option)
ANALOG FRONT END
F-ROM
(Image F-ROM
PEC Data (Program)
Memory)
block CODEC
(PM-22c)
F-ROM Card F-ROM
(Image, Boot) (CGROM)
Inside
SRAM (Option) (Smoothing Data)
PDL
MSC
(Option)
(DZAC000166)
IPC
LP AD9561
block
DANCE
(DZAC000234)
IOD-BUS +5V
PRIF
MN195004 CODEC
(1284)
(MODEM) (MN86064)
(Option)
G3B
INET LCU/LCE API
(Option)
2. Skyshot
D-BUS +3V
CCD A/D MN86076
(Sort Option)
ANALOG FRONT END
F-ROM
(Image F-ROM
Data (Program)
PEC Memory)
CODEC
block (PM-22c)
F-ROM Card F-ROM
(Image Boot)
, (CGROM)
Inside
SRAM (Option) (Smoothing Data)
PDL
MSC
(Option)
(DZAC000166)
IPC
LP AD9561
block
DANCE
(DZAC000234)
IOD-BUS +5V
PRIF
MN195004 CODEC
(1284)
(MODEM) (MN86064)
(Option)
G3B
LCU/LCE API
INET
(Option)
466
3. Scan into Memory
D-BUS +3V
CCD A/D MN86076
(Sort Option)
ANALOG FRONT END
F-ROM
(Image F-ROM
Data (Program)
PEC Memory)
block CODEC
(PM-22c)
F-ROM Card F-ROM
(Image, Boot) (CGROM)
Inside
SRAM (Option) (Smoothing Data)
PDL
MSC
(Option)
(DZAC000166)
IPC
LP AD9561
block
DANCE
(DZAC000234)
IOD-BUS +5V
PRIF
(1284) MN195004 CODEC
(MODEM) (MN86064)
(Option)
G3B
G3B
G4B
INET LCU/LCE API
INET
(Option)
(Sort Option)
ANALOG FRONT END
F-ROM
(Image F-ROM
Data (Program)
PEC Memory)
CODEC
block (PM-22c)
F-ROM Card F-ROM
(Image, Boot) (CGROM)
Inside
SRAM (Option) (Smoothing Data)
PDL
MSC
(Option)
(DZAC000166)
IPC
LP AD9561
block
DANCE
(DZAC000234)
IOD-BUS +5V
PRIF
(1284) MN195004 CODEC
(MODEM) (MN86064)
(Option)
G3B
INET LCU/LCE API
INET
(Option)
467
5. Page Numbering
D-BUS +3V
CCD A/D MN86076
(Sort Option)
ANALOG FRONT END
F-ROM
(Image F-ROM
Data (Program)
PEC Memory)
CODEC
block (PM-22c)
F-ROM Card F-ROM
(Image, Boot) (CGROM)
Inside
SRAM (Option) (Smoothing Data)
PDL
(Option) MSC
(DZAC000166)
LP AD9561 IPC
block DANCE
(DZAC000234)
IOD-BUS +5V
PRIF
MN195004 CODEC
(1284)
(MODEM) (MN86064)
(Option)
G3B
G3B
INET LCU/LCE API
(Option)
6. Overlay
D-BUS +3V
CCD A/D MN86076
(Sort Option)
ANALOG FRONT END
F-ROM F-ROM
(Image
Data (Program)
PEC Memory)
CODEC
block (PM-22c)
F-ROM Card F-ROM
(Image, Boot) (CGROM)
Inside
SRAM (Option) (Smoothing Data)
PDL
MSC
(Option)
(DZAC000166)
IPC
LP AD9561
block
DANCE
(DZAC000234)
IOD-BUS +5V
PRIF
MN195004 CODEC
(1284)
(MODEM) (MN86064)
(Option)
G3B
INET LCU/LCE API
(Option)
468
7. Memory Transmission
D-BUS +3V
CCD A/D MN86076
(Sort Option)
ANALOG FRONT END
F-ROM
(Image F-ROM
Data (Program)
PEC Memory)
CODEC
block (PM-22c)
F-ROM Card F-ROM
(Image, Boot) (CGROM)
Inside
SRAM (Option) (Smoothing Data)
PDL
(Option) MSC
(DZAC000166)
IPC
LP AD9561
block
DANCE
(DZAC000234)
IOD-BUS +5V
PRIF MN195004
(1284) CODEC
(MODEM)
(MN86064)
(Option)
G3B
INET LCU/LCE API
(Option)
8. Memory Reception
D-BUS +3V
CCD A/D MN86076
(Sort Option)
ANALOG FRONT END
F-ROM F-ROM
(Image
Data (Program)
PEC Memory)
CODEC
block (PM-22c)
F-ROM Card F-ROM
(Image, Boot) (CGROM)
Inside
SRAM (Option) (Smoothing Data)
PDL
MSC
(Option)
(DZAC000166)
IPC
LP AD9561
block
DANCE
(DZAC000234)
IOD-BUS +5V
PRIF MN195004
(1284) CODEC
(MODEM)
(MN86064)
(Option)
G3B
INET LCU/LCE API
(Option)
469
9. Report/List Printing
D-BUS +3V
CCD A/D MN86076
(Sort Option)
ANALOG FRONT END
F-ROM
(Image F-ROM
Data (Program)
PEC Memory)
CODEC
block (PM-22c)
F-ROM Card F-ROM
(Image, Boot) (CGROM)
Inside
SRAM (Option) (Smoothing Data)
PDL
MSC
(Option)
(DZAC000166)
IPC
LP AD9561
block
DANCE
(DZAC000234)
IOD-BUS +5V
PRIF
MN195004 CODEC
(1284)
(MODEM) (MN86064)
(Option)
G3B
INET LCU/LCE API
(Option)
(Sort Option)
ANALOG FRONT END
F-ROM
(Image F-ROM
Data (Program)
PEC Memory)
CODEC
block (PM-22c)
F-ROM Card F-ROM
(Image, Boot) (CGROM)
Inside
SRAM (Option) (Smoothing Data)
PDL
MSC
(Option)
(DZAC000166)
LP AD9561 IPC
block DANCE
(DZAC000234)
IOD-BUS +5V
PRIF
MN195004 CODEC
(1284)
(MODEM) (MN86064)
(Option)
G3B
INET LCU/LCE API
(Option)
470
11. PC Scanning Mode (Binary/Gray Scale Scanning)
D-BUS +3V
CCD A/D MN86076
(Sort Option)
ANALOG FRONT END
F-ROM
(Image F-ROM
Data (Program)
PEC Memory)
block CODEC
(PM-22c)
F-ROM Card F-ROM
(Image, Boot) (CGROM)
Inside
SRAM (Option) (Smoothing Data)
PDL
MSC
(Option)
(DZAC000166)
IPC
LP AD9561
block
DANCE
(DZAC000234)
IOD-BUS +5V
PRIF
(1284) MN195004 CODEC
(MODEM) (MN86064)
(Option)
G3B
INET LCU/LCE API
(Option)
(Sort Option)
ANALOG FRONT END
F-ROM F-ROM
(Image
Data (Program)
Memory)
PEC CODEC
block (PM-22c)
F-ROM Card F-ROM
(Image, Boot) (CGROM)
Inside
SRAM (Option) (Smoothing Data)
PDL
MSC
(Option)
(DZAC000166)
IPC
LP AD9561
block
DANCE
(DZAC000234)
IOD-BUS +5V
PRIF
MN195004 CODEC
(1284)
(MODEM) (MN86064)
(Option)
G3B
INET LCU/LCE API
(Option)
471
13. Multi-Size Feed
D-BUS +3V
CCD A/D MN86076
(Sort Option)
ANALOG FRONT END
F-ROM
(Image F-ROM
Data (Program)
PEC Memory)
CODEC
block (PM-22c)
F-ROM Card F-ROM
(Image, Boot) (CGROM)
Inside
SRAM (Option) (Smoothing Data)
PDL
MSC
(Option)
(DZAC000166)
IPC
LP AD9561
block
DANCE
(DZAC000234)
IOD-BUS +5V
PRIF
(1284) MN195004 CODEC
(MODEM) (MN86064)
(Option)
G3B
INET LCU/LCE API
(Option)
472
6.4.9. Modem and Peripheral Circuit
This circuit consists of DSP, ROM, S-RAM, Analog Front End, Analog Master and peripheral circuitry. This
modem conforms to ITU-T, V.34, V.33, V.17, V.29, V.27ter, V.21 channel 2 (FSK), T.4, and T.30. Macro order
of DSP is sent from ROM to S-RAM and is outputted. DSP transfers/receives data from Analog Front End
and serial communication. Analog Front End communicates with the line through Analog Master.
S-RAM
To Line
Analog Analog
Master Front DSP
To Speaker End
ROM
473
6.4.12. Line Monitor Circuit
The Line Monitor Circuit consists of an operational amplifier, analog master and its peripheral circuits. Its
function is to monitor the dial tone, DTMF tone, response signals, etc. over the speaker. It also sounds the
output of the key touch tones, alarm tones, etc. from the panel CPU over the speaker. The received signal
from the Ain (M) passes through an AGC circuit and is conditioned by the Analog Front-End DSP and is
then input to the Analog SW2 for volume control. The signal is then input to the Speaker Amplifier, where it
is amplified to a level sufficient to drive the speaker. The key touch tones and Buzzer Signals from the panel
are input to the Analog SW2 for volume control and then input to the Speaker Amplifier. The monitor tone
from the phone line and the buzzer tone from the panel can be adjusted from the Control Panel.
HYSIG
Analog Master Analog Front-End DSP
RX signal Analog SW1
HYBSR Ain(M)
Gain Switch
LPF Fc:7.8KHz
TX signal Amplifier
Aout(M) AGC
Hybrid Circuit
LPF Fc:4.5KHz
Analog SW2
Aout(V)
474
6.4.13. Line Control Board
The following shows a block diagram of the Line Control Board.
CN25 CN8
HYBSR HYBSR HYBSR
11 11
TCK
CML PC2 CML PC2 CML
PLS PLS
nHKOFF 9 nHKOFF 9
PC1
Off-Hook
RMCK
PC2 CLK PC2
7 7
+5V +5V
IC2
RMCS
P/S
8 8
Country
nCTON nCTON
PC2 Code RMDT
Q8
L : Ring In 10
Jumper 9 9 ApI L : Ring In 10
JP18~23
PC1
API API
+24V +24V +24V
5 5
CML H : FAX Side
CML L : Telephone CML
H : FAX Side Q4 H : FAX Side
L : Telephone CMLD L : Telephone
+24V
CMLD 5 6 6 CMLD 5
Q1 PLS Q1
H : Make
L : Break
PLS Q3 PLS
H : Make +24V Dial Pulse PLSD H : Make
L : Break L : Break
PLSD 6 TCK PLSD 6
Q2 Q2
14 14
Q1
Loop Relay TCKD
CN7 CN7
< LCU > < MDM > < LCE > <MDM> < LCE > < MDM >
The Ring Detector consists of a photocoupler, PC2 (PC1 for LCE), and its peripheral circuits. The ringing
signal is a half-wave rectifier in the Ring Detector, and transferred through the nCTON signal line to the
IC80 on the SC PC Board. The IC80 observes the signal to distinguish from signals caused by chattering.
The Off-Hook Detector (External Telephone) circuit consists of the photocoupler, PC1 (PC2 for LCE), and
its peripheral circuits. When PC1 detects loop current flow, it emits a Low active output signal (nHKOF) to
the IC80 which monitors it for a specified time. If the IC80 detects no change in the Low signal level, it
determines that the External Telephone is Off-Hook.
475
Dial Pulse Generator
The circuit consists of the CML relay, PLS relay and their peripheral circuits. This circuit generates dial
pulses. The CPU on the SC PC Board controls all dial pulse generation sequences. It turns relay CML
and PLS ON and OFF through the DZZSP58025 (IC80). The status of the relays during dialing is shown
below. When the absence of the terminating message is confirmed by the Off-Hook detector, the CPU
turns CML relay ON to develop loop status (DC loop). After a few seconds, the CPU turns the PLS relay
On and Off to generate dial pulses, making and breaking the loop.
Dial Pulse
break
CML Relay
make
break
PLS Relay
make
break
Prepause Inter-digit
Line status pause
make
The circuit is incorporated in the MODEM on the SC PC Board. The DTMF tone is conveyed to the
telephone line using the same route as the facsimile signal. The DTMF tone selection is controlled by the
CPU. The relay status during dialing is shown below.
DTMF Tone
break
PLS Relay
make
break
CML Relay
make
Inter-digit
Prepause pause
break DTMF signal
Line status
make
476
6.4.14. Panel PC Board
This Panel PC Board consists of Panel Control Sub-CPU, LCD Controller, Touch Panel Controller, S-RAM
Memory, FLASH Memory (Program, Image Data), Alarm IC (Backup), LED, and Key Switch.
The Sub-CPU receives the command of synchronized serial data from SC PCB and executes LCD Display,
LED Lamp, Switching Scan, Key Touch Sound, and Alarm Sound. The signal PON is turned to LOW with
the command from SC PCB and shifts to Sleep Mode. When Sleep Mode (Auto Off) is on, only +5VP is
reactivated and +5V (for LED Driver) and +24V (for Status LED, Alarm, and Back light) is cut off. After
detecting the signal nWAKEUP which is input from SC PCB, the signal nPOWSAVE is turned to HIGH in
order to recover from Sleep Mode and reactivate the main power of the machine.
CPU (SH7041)
NMI
nWAKEUP INTC A21 1
nSLPKY (8ch+NMI) F-ROM (Program)
nRTCIRQ (8M/16Mx16)
A/D A
A19 1
F-ROM (Program)
(16Mx16)
POWSAVE
A
A15 11
S-RAM (64KB)
)
)
1
A 11
A21
A15 LCDC
(LCD Controller)
LCD Module
D3 1
D15 1
EDMMR63B0F
M66272FP
TPCCLK
TPC
TPCTX
TXD SCI (Touch Panel
Matrix Data
Touch Panel
(2ch) EMU601A2MA12
RXD TPCRX
Controller)
ADS7843
DBGTX
DBGRX
A3 1
A3 1
RTC
PD4992
BZCLK
LEDCT0,1
MTU
(5ch)
LED0 7 PNL2
(SW Board)
SCN0 7 KEY: MAX40
LED: MAX14
KEYIN0 7
477
The machine will recover from Sleep Mode by the following conditions.
1. Push on Energy Saver Key
2. Original Sensor Actuated
3. Signal Detected
4. Off-Hook (Handset)
5. Off-Hook (External Telephone)
6. Data Signal from Printer I/F
+5Vp
Panel
Micro
Computer
+5Vp +5Vp
+5V +5V
Power
nPWSAVE
nP
nMPOFF
+5V
External 16Hz
CT1ON
n 5VOFF SH2
Ex-TEL Off-Hook
Handset Off-Hook SC
HSDT
OPON
G3B G3B 16Hz
PRT WKUPPC
Set Document
TP
APN
Centronics
Parallel
Sensor
I/F
PCB
PC
478
6.4.15. Laser Printer Motor Drive Circuit
1. System Description
It consists of 16 bit CPU M30620SFP (for DP-2000/2500) or M30805SGP (for DP-3000), FROM for
programming, peripheral I/O, and IPC Micro computer for Finisher I/F. The CPU controls mechanism of
Laser Printer, Fuser Lamp temperature, and Laser Unit.
nCS
CPU nCS0 F-ROM
(M16C/62:DP-2000/2500) (512KB)
(M16C/80:DP-3000)
nCS1
nCS2
nCS
API
nCS
IPC
479
2. Reset Circuit
This circuit consists of IC301 (PST575E) and peripheral circuit. This circuit always watches 5V. Output
of this circuit (nRST) is set that if 5V falls below setting level (3.9V). When the 5V rises above voltage,
the reset signal is canceled after a delay of approximately 20 ms. After cancelling, software is started
by CPU.
1
R320
R321
IC101
IC301
3 2 R105 CPU
PST575E
C103
C305
4
pLPRST
Q303
Reset Circuit
Vdd
5V
3.9V
td td td=20ms
480
3. Printer Motor Drive Circuit
This Printer Motor is a Brushless DC Motor.
nMMON : When the signal level goes Low, the Printer Motor starts rotating.
nMMRDY : Rotation status signal for Printer Motor. When the Printer Motor reaches a
constant speed, nMMRDY signal level goes Low.
nMMCK : Clock signal for Printer Motor Drive
The Printer Motor is powered by +24 VDC supply. When the interlocks are open, the +24 VDC supply
is cut off and the Printer Motor stops rotating.
+24VM CN714
1 +24VM
MGND
2
M
+5V 1 MGND
R639 2 nMMON DC Brushless
3 nMMRDY Motor
4 nMMCK
IC200 Q604 Q605 CN723
481
4. Fuser Lamp Drive Circuit
It consists of 2 Fuser Lamps and each Fuser Lamp is controlled by two HTC PC Boards.
The Fuser Lamp is powered by 100 VAC. When the CN765, Pin 6 (nSSR) on the HTC PCB goes LOW,
the Fuser Lamp turns ON. This lights up the PC101 LED and activates the SCR101 photo-triac, and
100 VAC is sent to the Fuser Lamp.
(Outside 850W)
(Inside 400W)
ACSW
Thermostat Fuse
Fuser Lamp 1
Fuser Lamp 2
CN767
CN766
CN764
CN760
CN761
2
1
(HTC 1 PCB)
(HTC 2 PCB)
F101
RL101
C101
L101
L101
R105
R106
C102 C102
R101 R101
SCR101
+ ~
- ~
D101
SCR101
R102
C103
R102
C103
R107
R103 R103
3 R104 PC101
PC102
R104 PC101
CN765
CN768
4
1
2
6
4
5
+5V 7
8
4
CN732
(LPC PCB)
CN708
+5V
nSSR1
nSSR2
482
5. Fuser Temperature Control Circuit
The fuser temperature is controlled by IC101 on the LPC PC Board, which contains A/D (Analog/
Digital) converters. IC101 adjusts temperature, observing two Thermistors and voltages separated by
R418 and R439 with A/D converters. When the PC101 drive current is transmitted from the LPC PC
Board to the HTC PCB, the Fuser Lamp turns ON. IC401 is a converter with open output at pins 1 and
7 and is used as an abnormal temperature detection circuit. IC401, pin 1 and 7, has a high impedance
when Q407 and Q413 are activated, turning ON the Fuser Lamp. An abnormal temperature is detected
when the VTH voltage level becomes higher than V+, forcing IC401, pin 1 and 7 Low and
deactivating Q407 and Q413.
Abnormally low and high temperatures, as well as Thermistor release status, are detected by IC101
(CPU) programming.
Thermistor
Thermistor
(LPC PCB)
CN716 +5V
4 2
VTH - IC401
3 1
+5V V+ +
C402
R418
R416 R417
1
3 +5V
2 R415 R448
6
VTH - IC401
7
+5V V+ +
R439
C418
R441
5
R442 CN765
+5V +5V
R440
9 PC101
+5V 5 R104
R449
CN708
R450
+5V
CN732
R451
IC404 Q413
Q414 3 6
CN765 (HTC 2 PCB)
483
6. Interlock Safety Circuit
This safety circuit turns OFF the +24 VDC and +5 VDC supply voltages when the Printer Cover is
opened. When the Printer Cover is opened, the microswitch(es) on the ILS PC Board are de-actuated,
turning OFF +24 VDC to the Printer Motor Drive Circuit, the HVPS, the Paper Feed Solenoid Circuits,
the Clutch Drive Circuit, and the Laser Driver Circuit on the Laser Unit.
Printer Motor
LPC PCB Paper Feed Clutch
+24V Lift DC Motor
+24VM Multi Feeder Feed Roller
Right Clutch
Cover +24VD1 Counter
2nd Paper Feed Module
3rd Paper Feed Module
Micro Q415
4th Paper Feed Module
Switch
Dual-Path Exit Guide Unit
+24VHL Paper Transport Unit
Front +24VD2
Cover
HVPS
Q607
LSU (Motor)
DC/DC
Converter MA152A L+5V
1W 270
1W 270 TA78M05F LSU (Laser)
Open Door IN OUT
1W 270 GND
+
Detection +
MGND
484
7. LSU Control Circuit
The laser control signals are described below.
Actual data is sent from SC PCB to LSU.
SC PCB
IC47 IC49 3
IC46
VIDEO DATA
4
VIDEO+
VIDEO-
CN701
IC702 R331 1 nS/H Laser
R358 2 nHSYNC Control Laser
5 nLDON Circuit
IC702 R333 6 pLDCTL
IC101 8 VCONT
CPU IC701 R371 Timing
R365 R369 Sensor
R364
nPMCK
R370
R335
10 nPMRDY Motor
Q305
9 nPMCK Drive
11 nPMON Circuit
Q304
Scanner
Motor
485
7 Exploded View & Parts List
7.1. Country Codes
CAUTION: denotes hazards that could result in minor injury or damage to the machine.
• This product contains a Lithium Battery. Danger of explosion if the battery is incorrectly replaced.
Replace only with the same or equivalent type. Dispose of used batteries according to the instructions of your local solid waste officials.
Note:
1. Panasonic Document Imaging Company reserves the right to change any information enclosed herein without prior notification. (This includes, but is not limited to, parts pricing and availability, and text)
2. Electrical parts supplied may include previously used components.
3. Important safety notice
Components identified by mark have special characteristics important for safety.
When replacing any of these components, use only manufacturer's specified parts.
4. In New Parts column, "N" indicates part is used only in DP-2000/2500/3000 model, "C" indicates part is used in previous models.
486
7.2. Control Panel Unit
487
Safety Ref New
Part No. Part Name Note AA AB AC AD AE AF AG AH AJ AK AL AM AN AP AQ AR AS AT AU AV AW ED EE YA YB YC YE YF YG YH YJ YM YN YR YS YT YU YV YW YX YY
Mark No. Parts
DZMA002537 Cover, Control Panel - - 1 - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - 1
DZMA002615 Cover, Control Panel - 1 - 1 - 1 - 1 1 1 1 1 1 1 1 1 1 1 - - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 -
DZMA002636 Cover, Control Panel - - - - - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - -
129 N For DP-2000
DZMA002638 Cover, Control Panel - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1 - - -
DZMA002637 Cover, Control Panel 1 - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZMA002639 Cover, Control Panel - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
130 DZMA002538 Cover, LCD Panel N For DP-2000 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
DZNA000712 Sheet, Copy Size(English) - - 1 - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - 1
DZNA000721 Sheet, Copy Size (English) - 1 - 1 - 1 - 1 1 1 1 1 1 1 1 1 1 1 - - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 -
DZNA000727 Sheet, Copy Size (German) 1 - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
131 N For DP-2000
DZNA000728 Sheet, Copy Size (Chinese) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1 - - -
DZNA000726 Sheet, Copy Size (French) - - - - - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - -
DZNA000729 Sheet, Copy Size (Taiwanese) - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZNA000720 Sheet, MODE (English) - 1 1 1 - 1 - 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 - 1 1 1 - 1 1 1 1 1 1 1 - 1 1 1
DZNA000723 Sheet, MODE (German) 1 - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZNA000724 Sheet, MODE (Chinese) For DP-2000, Fax Communication Kit - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1 - - -
DZNA000722 Sheet, MODE (French) - - - - - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - -
DZNA000725 Sheet, MODE (Taiwanese) - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
132 N
DZNA000715 Sheet, MODE (English) - 1 1 1 - 1 - 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1
DZNA000731 Sheet, MODE (German) 1 - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZNA000732 Sheet, MODE (Chinese) For DP-2000 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1 - - -
DZNA000730 Sheet, MODE (French) - - - - - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - -
DZNA000733 Sheet, MODE (Taiwanese) - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
133 DZNA000717 Film, F N For DP-2000 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
134 DZDA000028 LCD UNIT N For DP-2000 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
135 DZNB000099 Window, LCD N For DP-2000 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
136 DZKB000674 Button, B Green N For DP-2000 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
137 DZKB000669 Button, B Blue N For DP-2000 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
DZNA000719 Sheet, MODE (English) - 1 1 1 - 1 - 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1
DZNA000735 Sheet, MODE (German) 1 - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
138 DZNA000736 Sheet, MODE (Chinese) N For DP-2000 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1 - - -
DZNA000734 Sheet, MODE (French) - - - - - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - -
DZNA000737 Sheet, MODE (Taiwanese) - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
139 DZKB000664 Key, 4Way N For DP-2000 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
140 DZHA000156 Sheet, Insulation N For DP-2000 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
DZFP000871 Harness, PNL1-INV - - 1 - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - 1
1907 N
DZFP000955 Harness, PNL1-INV 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1908 DZFP000872 Harness, PNL1 N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
DZFP000873 Harness, PNL3 - - 1 - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - 1
1909 N
DZFP000954 Harness, PNL3 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
DZFP000874 Harness, PNL2 - - 1 - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - 1
1910 N
DZFP000953 Harness, PNL2 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1914 DZFP000905 Harness, PNL-FG N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
DZEC101955 PC Board, PNL1 (DP-2500) 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 - 1 1 1
DZEC101732 PC Board, PNL1 (DP-2500 PK) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1 - - -
19120 N
DZEC101818 PC Board, PNL1 (DP-2500 PT) - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZEC101889 PC Board, PNL1 (DP-2500 PL) - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - 1 - - - - - - - - - - - -
19121 DZEC101549 PC Board, PNL2 N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
19125 DZEC101633 PC Board, PNL3 N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
19153 DZFP000909 Harness, PNL2 N For DP-2000 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
19154 DZFP000910 Harness, PNL4 N For DP-2000 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
19155 DZFP000980 Harness, PNL-FG N For DP-2000 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
19156 DZEC101635 PC Board, PNL4 N For DP-2000 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
19 XTB3+8J Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
2K XTB26+12J Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
7B XTB26+6J Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
B1 DZPB000007 Screw, Silver C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
488
A B C D E F G H I J K
126
105 1
114
115
116
101
2
102
104
B1
3
119
7B
118
120
121 103
4
123
122
108 117
125 5
109 107
119 PNL1
CN63
106
1907 19121
112 110
111 19 19120 6
1910
127 113
PNL1
CN66
124 1914
1909
7
1908
SC
CN108
19125 128
7B
PNL1 To 1909
CN61 124
To PNL3 8
7B 2K 123 CN70
7B 7B Fig. 1 Control Panel Unit
489
A B C D E F G H I J K
131
126
1
114 105
132
129 2
135
B1
130 104
119
7B
133 138
118
120
137 121 103
119 4
137
108 122
109
7B
7
128
7B 19156
19155 8
7B Fig. 1-a Control Panel Unit
490
7.3. Scanner Unit
491
Safety Ref New
Part No. Part Name Note AA AB AC AD AE AF AG AH AJ AK AL AM AN AP AQ AR AS AT AU AV AW ED EE YA YB YC YE YF YG YH YJ YM YN YR YS YT YU YV YW YX YY
Mark No. Parts
260 DZFR000024 Cable, FPC N PM 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
(Flexible Printed Cable)
261 DZHA000145 Insulation Sheet B, FPC Cable N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
262 DZHA000146 Insulation Sheet C, FPC Cable N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
263 DZJM000445 Sheet, Damper N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
264 DZTC000039 Mirror 1 N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
265 DZTC000040 Mirror 2 N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
267 DZNK002793 Caution Label, FPC N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
268 DZEA000047 PC Board, Inverter N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
269 DZHP004387 Sensor 3, Size N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
270 DZAL000003 Sensor N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
271 FFPFJ0041 Ring, Snap N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
272 DZJC000287 Bracket, Heater N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
273 DZFR000013 Thermistor Assembly C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
274 DZJB000189 Base, Sensor S N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
275 DZHP004388 Sensor 1, Size N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
276 DZKP000223 Plate Spring F N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
277 DZKP000224 Plate Spring R N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
280 DZFR000027 Thermistor N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
281 DZJM000483 Seal, Reflection N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
282 DZKG000137 Shaft Assy, Drive N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
446 DZJK000006 Clamp, Harness N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
466 DZJM000490 Sheet, Base N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
556 DZPB000031 Screw, Shoulder N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
DZFP000903 Harness, SCN-INV - - 1 - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - 1
1901 N
DZFP000960 Harness, SCN-INV 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1903 DZFP000867 Harness, OPS N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1904 DZFP000868 Harness, BMT N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1905 DZFP000869 Harness, BDC N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1906 DZFP000870 Harness, FPC N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
DZFP000877 Harness, CCD - - 1 - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - 1
1915 N For DP-2000/2500
DZFP000953 Harness, CCD 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1927 DZFP000896 Harness, Heater 2 N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1928 DZFP000907 Harness, Heater 1 N - - 1 - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - 1
19128 DZEC101683 PC Board, LFB N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
19157 DZFP001004 Harness, CCD 1 N For DP-3000 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
18 XYN3+J6 Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
19 XTB3+8J Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
36 XYN3+F6 Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
5Y XUC4 E-Clip C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
D24 DZPA000013 Screw, Red C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
D25 DZPA000014 Screw, Blue C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
F6 DZPK000021 Washer N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
492
A B C D E F G H I J K
232 207
19
281 204 282
248 19157
232 LFB 221 1
18 D24 CN181 203
231
238 228
281 CONS 1915
264 219 CN57
248
211 D24 271
SC
210 227 202 CN106
265 235 230 2
211 221 RLB
CN172
214 18 224 19
211 226 203
225 1927
206 236 252 209 1901 272
214 To
230 204 1928
237 223 254
SCN
234 CN9 3
212
206 233 211 219
19 251 19
260 280
265 258 19
215 19128
To
263 268 LFB
CN181 19
229
19128 SCN 4
211 CN7 1905 1906
216
259 SCN 1905 269
5Y 268 213 19
CN7
243 F6 245 466
208 19 D24
217 19
19 250 267
19 249 275 254
246
270 277 5
SCN
CN6 271 274
36
240 SCN 244
CN8 201
RLB 1903
CN172 255 272 446
6
1904 1927 SCN
CN7
19 446
19
242 1928
273 1905
241 261 269
276
D25
19 262 239 7
19
250
247
255
271 245
240 446
F6 556
8
Fig. 2 Scanner Unit
493
7.4. Electrical Parts
494
Safety Ref New
Part No. Part Name Note AA AB AC AD AE AF AG AH AJ AK AL AM AN AP AQ AR AS AT AU AV AW ED EE YA YB YC YE YF YG YH YJ YM YN YR YS YT YU YV YW YX YY
Mark No. Parts
DZEZ000026 PC Board, SC (DP-2000 PB) - 1 - - - - - - - 1 - - - - 1 - - - - - - - - - - - 1 - - - - 1 - - - - 1 - - 1 -
DZEZ000025 PC Board, SC (DP-2000 PA) - - - - - - - - - - 1 - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - -
DZEZ000027 PC Board, SC (DP-2000 PE) - - - - - - - - - - - - - - - - - 1 - - - 1 - - 1 1 - 1 - 1 1 - 1 1 - 1 - - 1 - -
DZEZ000028 PC Board, SC (DP-2000 PF) - - - - - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - -
DZEZ000029 PC Board, SC (DP-2000 PG) - - - - - - - - - - - 1 - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - -
DZEZ000030 PC Board, SC (DP-2000 PK) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1 - - -
1983 DZEZ000031 PC Board, SC (DP-2000 PL) N For DP-2000 - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - 1 - - - - - - - - - - - -
DZEZ000032 PC Board, SC (DP-2000 PM) 1 - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZEZ000033 PC Board, SC (DP-2000 PQ) - - - - - - - - - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - -
DZEZ000034 PC Board, SC (DP-2000 PS) - - - 1 - - - - - - - - 1 - - - 1 - - - - - - - - - - - - - - - - - - - - - - - -
DZEZ000035 PC Board, SC (DP-2000 PV) - - - - - - - 1 - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - -
DZEZ000036 PC Board, SC (DP-2000 PX) - - - - - 1 - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZEZ000037 PC Board, SC (DP-2000 PY) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1 - - - - - -
1984 DZEC101632 PC Board, SORT N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
DZEC101737 PC Board, FXB (A) - - 1 - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - 1
DZEC101738 PC Board, FXB (F) 1 1 - 1 - 1 1 1 1 - - 1 1 1 1 1 1 - - 1 - - 1 - - - - - 1 - 1 - - - - - - - 1 - -
1985 N
DZEC101739 PC Board, FXB (G) - - - - 1 - - - - - - - - - - - - 1 - - - 1 - 1 1 - 1 1 - - - 1 1 1 1 1 1 1 - 1 -
DZEC101767 PC Board, FXB (E) - - - - - - - - - 1 1 - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - -
DZEC101901 PC Board, LANB - - - - - - 1 - - - - - - - - - - - - 1 - - 1 - - - - - - - - - - - - - - - 1 - -
1987 N
DZEC101751 PC Board, LANB - 1 1 - - - - - - 1 1 - - - 1 - - - 1 - - - - - - - - - - - - - - - - - - - - 1 -
1989 DZEC101375 PC Board, LANC C - 1 1 - - - 1 - - 1 1 - - - 1 - - - 1 1 - - 1 - - - - - - - - - - - - - - - 1 1 -
DZEC101321 PC Board, LCE 1 1 - 1 - 1 1 1 1 - - 1 1 1 1 1 1 - - 1 - - 1 - - - - - 1 - - - - - - - - - - - -
DZEC101330 PC Board, LCE - - - - 1 - - - - - - - - - - - - 1 - - - 1 - 1 1 - 1 1 - - - 1 1 1 1 1 1 1 - 1 -
DZEC101716 PC Board, LCE - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1 - -
1994 DZEC101712 PC Board, LCE N - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZEC101714 PC Board, LCE - - - - - - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - -
DZEC101715 PC Board, LCE - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1 - - - - - - - - - -
DZEC101713 PC Board, LCE - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
1995 DZEC101791 PC Board, LCU N - - 1 - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - 1
DZEC101607 PC Board, HTC (100V) - - 1 - 1 - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - 1
1997 N
DZEC101724 PC Board, HTC (200V) 1 1 - 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -
DZEC101755 PC Board, HTC 2 (100V) - - 1 - 1 - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - 1
1998 N
DZEC101756 PC Board, HTC 2 (200V) 1 1 - 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -
ETXDN281ABD Low Voltage PSU (100V) - - 1 - 1 - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - 1
1999 N
ETXDN281EBD Low Voltage PSU (200V) 1 1 - 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -
DZEC101753 PC Board, FRM For PCL6 Emulation Kit 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
19118 DZEC101781 PC Board, FRM (G3B) C - - 1 - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - 1
For 2nd G3 Fax Communication Kit
DZEC101782 PC Board, FRM (G3B) 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 - 1 1 1 - 1 1 1 1 1 1 1 1 1 1 -
19119 DZEC101696 PC Board, EP C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
DZEC101554 PC Board, SDRM (8 MB) For Image Memory 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
DZEC101666 PC Board, SDRM (16 MB) For Image Memory, 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
19122 N
For Automatic Duplex Unit
DZEC101667 PC Board, SDRM (128 MB) For Image Memory 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
DZEC101665 PC Board, RLB (100V) - - 1 - 1 - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - 1
19127 N
DZEC101745 PC Board, RLB (200V) 1 1 - 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -
DZEC101686 PC Board, LPC (100V) - - 1 - 1 - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - 1
For DP-2000/3000
19129 DZEC101940 PC Board, LPC (200V) N 1 1 - 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -
DZEC101944 PC Board, LPC For DP-3000 1 1 - 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -
ETXDN282A4A Optional Low Voltage PSU (100V) - - 1 - 1 - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - 1
19130 N
ETXDN282E4A Optional Low Voltage PSU (200V) 1 1 - 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -
DZEC101740 PC Board, G3B (K) - - 1 - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - 1
DZEC101741 PC Board, G3B (Q) 1 1 - 1 - 1 1 1 1 - - 1 1 1 1 1 1 - - 1 - - 1 - - - - - 1 - 1 - - - - - - - 1 - -
19134 C
DZEC101742 PC Board, G3B (R) - - - - 1 - - - - - - - - - - - - 1 - - - 1 - 1 1 - 1 1 - - - 1 1 1 1 1 1 1 - 1 -
DZEC101766 PC Board, G3B (P) - - - - - - - - - 1 1 - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - -
19142 DZEC101792 PC Board, HCE N 1 1 - 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -
19158 DZEC101947 PC Board, CONS N For DP-3000 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
3006 DZAA001208 Interface Board, IPC N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
3007 DZJH000078 Spacer N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
3804 DZHP004034 Assy, LANC-BK N - 1 1 - - - 1 - - 1 1 - - - 1 - - - 1 1 - - 1 - - - - - - - - - - - - - - - 1 1 -
495
Safety Ref New
Part No. Part Name Note AA AB AC AD AE AF AG AH AJ AK AL AM AN AP AQ AR AS AT AU AV AW ED EE YA YB YC YE YF YG YH YJ YM YN YR YS YT YU YV YW YX YY
Mark No. Parts
19 XTB3+8J Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
496
A B C D E F G H I J K
1
309
19134 19135
19 19 19
314
19118
19119
306 311 19118 311 19118
19122 312
1985
19122 2
19
301
424
421
19134
3
1987
445
302 19129
19
19 19122
To
Finisher 3006
1983
4
1975 19 3007
305
Option 19
LPC LVPS CN
IPC CN731 65/66
J2
425
5
417 19127
19
431
1994
1995
6
433
19
310
430
19
19
7
1999 307 1998
19
1989 307
19130 19142
3804 1994
1995 19
1997 8
19 313 Fig. 3 Electrical Parts
497
7.5. Frame Parts
498
Safety Ref New
Part No. Part Name Note AA AB AC AD AE AF AG AH AJ AK AL AM AN AP AQ AR AS AT AU AV AW ED EE YA YB YC YE YF YG YH YJ YM YN YR YS YT YU YV YW YX YY
Mark No. Parts
468 DZJA000789 Plate, HK N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
471 DZJJ000009 Band C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
473 FFPTE2110 Label, FCC/IC N - - 1 - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - 1
475 DZNK002989 Label, HHS N - - 1 - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - 1
476 DZJB000194 Plate, EMI N 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -
477 DZHB000019 Seal, Aluminum N 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -
480 DZNK003082 Label, SW N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
481 DZNK003066 Seal, Circuit N - - 1 - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - -
482 DZHA000160 Sponge, EMI N 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -
273 DZFR000013 Thermistor Assembly C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1126 FBA08A24L0 Fan N PM 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1917 DZFP000911 Harness, SPK 2 N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1
1921 DZFP000882 Harness, Fan N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1930 DZFP000920 Harness, Heater 3 N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1931 DZFP000901 Harness, INLET FG N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1950 DZFP000838 Harness, HVPS N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1954 DZFP000842 Harness, ILS N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1962 DZFP000852 Harness, Inlet-ACSW N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1991 DZEC101661 PC Board, PRIF N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
19136 DZFP000942 Harness, PNL N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
19141 DZFP000878 Harness, SPK 1 N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1
19 XTB3+8J Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
D24 DZPA000013 Screw, Red C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
E5 XTB3+32J Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
E6 XTB3+24J Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
499
A B C D E F G H I J K
SC 450 HTC2 TO
CN125 CN766 FG
1917 19
8
19 Fig. 4 Frame Parts
500
7.6. Cover Assembly
501
Safety Ref New
Part No. Part Name Note AA AB AC AD AE AF AG AH AJ AK AL AM AN AP AQ AR AS AT AU AV AW ED EE YA YB YC YE YF YG YH YJ YM YN YR YS YT YU YV YW YX YY
Mark No. Parts
DZHP003857 Glass Assembly - - 1 - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - 1
557 N
DZHP003858 Glass Assembly 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -
558 DZKP000188 Plate Spring, GL Holding N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
559 DZTE000024 Glass, S N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
560 DZFN000060 Cord, Handset N - - 1 - 1 - - - - 1 - - - - - - - 1 1 - - 1 - 1 1 - 1 1 - - - 1 1 1 1 1 1 1 1 1 1
DZFN000082 Cord, Cradle - - 1 - 1 - - - - - - - - - - - - 1 1 - - 1 - 1 1 - 1 1 - - - 1 1 1 1 1 1 1 1 1 1
561 N
DZFN000115 Cord, Cradle - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
562 DZNK002913 Guide, Toner Cartridge N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
563 DZNK000023 Guide, Toner Cartridge C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
564 DZNK003080 Label, Heater N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
565 FFPTE2650 Label, Energy Star C - - 1 - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - 1
566 DZJA000786 Bracket, KC N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
567 DZHE000032 Sponge, Dehumidifier N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
937 DZLF000342 Gear, E20 N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1008 DZLM000109 Bushing, P3.5L5 N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1013 DZLF000357 Gear, E18 Drive N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1049 DZLA000083 Roller, Idle C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
DZFP000903 Harness, SCN-INV - - 1 - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - 1
1901 N
DZFP000960 Harness, SCN-INV 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1902 DZFP000866 Harness, SCN N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1903 DZFP000867 Harness, OPS N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1904 DZFP000868 Harness, BMT N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1905 DZFP000869 Harness, BDC N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1935 DZFP000973 Harness, ADF N 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
DZEC101551 PC Board, SCN For DP-2000/2500 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
19114 N
DZEC101969 PC Board, SCN For DP-3000 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
DZEC101626 PC Board, SRU - - 1 - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - -
DZEC037110 PC Board, SRU - - - - - - - - - - - - - - - - - - - - - 1 - - 1 - 1 1 - - - 1 1 1 1 - 1 1 - 1 -
DZEC037300 PC Board, SRU - - - - - - - - - - - - - - - - - - - - - - - 1 - - - - - - - - - - - 1 - - - - 1
DZEC037400 PC Board, SRU - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
19117 N
DZEC037500 PC Board, SRU - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZEC037700 PC Board, SRU - - - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - -
DZEC037900 PC Board, SRU - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZEC101813 PC Board, SRU - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1 - -
19139 DZFP000928 Harness, KEY N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
19140 FFPWC0392 Harness, KC C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
19 XTB3+8J Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
2B XTB3+14J Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
6A XTB3+12J Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
B1 DZPB000007 Screw, Silver C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
B9 DZJM000171 Ring, Snap C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
C2 DZPB000020 Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
C8 XTW3+8SFC Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
F4 DZPA000063 Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
502
A B C D E F G H I J K
B1
501
19 557 19114
507
CN7 SCN CN6
1905 1903 1
516
B1 CN8 CN9
559 1904 1901
1902 1935
556 CN2 CN3
508 558
502
509 2
503 19114 F4
19
19
515 19 566
B1
567
6A 19 512 B1
510 513 3
504 514 19140
519 19139
505
511 B1
19 524
SC
CN102
B1 506 523
542
4
B1
564 537 LCU/
LCE
CN23
517 525
B1
560 561
518 562
19117 5
551 538 543
B9
937 2B 19
552 539
1049 1013 545 19
19 540 541 19
1008
555
554 6
553 544
549
C2 19 2B
548
19 527 528
556 536
542
C8 7
19 526
537 535
550
565
503
7.7. Stand for 1-4 Paper Tray Configuration
504
A B C D E F G H I J K
623
623
3
620
624
620
619
619
623
4
624
623
621
5
623 621
624 623
6
620 624
620
623
7
619
623
621
619
621
8
Fig. 6 Stand for 1-4 Paper Tray Configuration
505
7.8. Cartridge Unit
506
Safety Ref New
Part No. Part Name Note AA AB AC AD AE AF AG AH AJ AK AL AM AN AP AQ AR AS AT AU AV AW ED EE YA YB YC YE YF YG YH YJ YM YN YR YS YT YU YV YW YX YY
Mark No. Parts
775 DZJM000398 Sponge, Front Development N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
776 DZJM000399 Sponge, Rear Development N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
777 DZKN000226 Joint, Agitator N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
778 XPJ3E20 Pin C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
779 DZPA000062 Thumb Screw N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
782 DZJM000492 Seal, Development N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
783 DZHP004158 Star Wheel N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
784 DZKP000225 Plate, Star Wheel N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
786 DQ-TU18B Toner Case Assembly N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
787 DZSL000034 Label, Process Unit Caution N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
788 DZHP004086 Box, Waste Toner N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
789 DZJM000508 Sponge, OPC Cover N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1781 DZPG000001 Pin N PM For DP-3000 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
B4 XTB3+8JK Screw, Black C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
507
A B C D E F G H I J K
721
709 709 789
726
B4
784
720
704 1
B4
783
1781
762 726
B4 716
714
768 2
728 B4
B4 724
743
763
765
7
761
764 755
767
787 750
766
779
744 775
B4 8
Fig. 7 Cartridge Unit
508
7.9. Paper Tray
509
A B C D E F G H I J K
4N 815
816
23
809
810 1
804 808
B9
803
805
4N
3
814
806
4N 5
4N
6
4N
801
802
7
812
8
Fig. 8 Paper Tray
510
7.10. Drive Unit
511
A B C D E F G H I J K
23
23 942 911
918 1
924
952
B9
922 946
921 950
19 915
914 920 916
2
19
917 910
1946 913 937 951
19 908
906 928
904
901 919 934
902 3
925
LPC
CN714
/ 723 914
905 23
902 928 927
912 935 931
940
B9
926
907 4
933 929
934
953
903 928
932
19 931
930 5
944
B9
945
271 928
932 929
6
947
19 937
936
941
939 7
908
938
936
8
Fig. 9 Drive Unit
512
7.11. Fuser Unit
513
Safety Ref New
Part No. Part Name Note AA AB AC AD AE AF AG AH AJ AK AL AM AN AP AQ AR AS AT AU AV AW ED EE YA YB YC YE YF YG YH YJ YM YN YR YS YT YU YV YW YX YY
Mark No. Parts
1059 DZNK003287 Label, Jam Release N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1060 DZJM000526 Sheet, Separation N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1061 DZHD000016 Sheet, Insulation N For DP-3000 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
937 DZLF000342 Gear, E20 N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
941 DZLF000354 Gear, E25 N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1955 DZFP000843 Harness, EXTSEN N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1958 DZFP000846 Harness, EXTSEN/THERM Relay N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1960 DZFP000849 Harness, Heater 1 N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1961 DZFP000850 Harness, Heater 2 N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
16 XYN3+J8 Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
19 XTB3+8J Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
23 XYN3+F8 Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
36 XYN3+F6 Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1Q XYN3+F10 Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
4N XSN3+W8FC Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
C8 XTW3+8SFC Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
514
A B C D E F G H I J K
1958 1005 4N
LPC 1955 1045
CN716 1035 1037
1059
1022
To 1020 1011 1
1043
FD
1002 1060 C8
To
1049 4N
To FA 1036
FE
HTC
CN764 2
1007
1044 1026 1960
HTC 1960 1050 1034
CN764
1050 400W 19
HTC 1960
1030 To CN764 To 3
FC 937 1050 FC
941 16
1014 1029 To
1012 1033 FB
1961 19
1006
1009 1052 850W 16
1013 19
1046
LPC
CN716 LPC To
CN716 FA 4
1032 1016 16
1958
1958
1041
1053 1Q 1Q 1027
1017
1028
1042 1039
5
1033
1047
1018 1008
To
4N 1052
FE 1021
1046
To 1029
FD 1006 1039 6
4N 4N 1023
1051 1030 1015
1038 4N
1048 1047 1004
To 1019
23 FB
4N 1054 1003
1047 7
1961
1047
1040 1058
1018
1053
1061
1057
36 8
1056 Fig. 10 Fuser Unit
515
7.12. Paper Feed Module
516
Safety Ref New
Part No. Part Name Note AA AB AC AD AE AF AG AH AJ AK AL AM AN AP AQ AR AS AT AU AV AW ED EE YA YB YC YE YF YG YH YJ YM YN YR YS YT YU YV YW YX YY
Mark No. Parts
1159 DZGT000028 Brush Ground C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1160 DZHA000149 Film, Inner Cover C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1161 DZJM000474 Sheet, Protection C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1162 FFPKE10251 Box, Lift C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1163 FFPKE10261 Cover, Box C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1164 FFPMF10271 Gear 1 C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1165 FFPMF10281 Gear 2 C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1166 FFPMF1029 Gear 3 C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1167 FFPMF1030 Gear 4 C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1168 FFPWE00611 Motor, Lift C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1169 FFPMF1031 Gear, Worm C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1170 FFPLP0976 Spring, Reset C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1171 FFPHQ0063 Coupling C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1172 FFPFJ00441 Ring, Stopper C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1173 DZLM000103 Collar N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1174 DZLM000119 Brush, Feed N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
DZNK003067 Label,Laser Caution 1 1 1 - - - 1 1 - 1 1 1 - 1 1 1 - - 1 1 1 - 1 - - - 1 - 1 - - 1 - - 1 - 1 - - 1 1
DZNK003068 Label,Laser Caution - - - - - - - - - - - - - - - - - 1 - - - 1 - - 1 1 - 1 - 1 1 - 1 1 - 1 - 1 1 - -
1175 N
DZNK003069 Label,Laser Caution - - - - - 1 - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZNK003070 Label,Laser Caution - - - 1 - - - - - - - - 1 - - - 1 - - - - - - - - - - - - - - - - - - - - - - - -
1176 HLPMMA1017P Spring, Cover N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1177 HLPMMA1017P Sheet, 1st N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1178 HLPLGA2005P Cover F, Dust N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1179 HLPLLA1019 Sponge F, LD N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1180 HLPLLA1023 Sheet, LD N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1181 DZPJ000016 C-Clip N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
271 FFPFJ0041 Ring, Snap N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
446 DZJK000006 Clamp, Harness N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
806 DZLA000198 Roller, Paper Tray N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1045 DZAL000072 Sensor N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1230 DZFP000747 Resistor, 200M Ohms N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1258 DZLF000325 Gear, B27 N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1259 DZKG000106 Shaft, Clutch N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1260 DZGA000007 Clutch N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1918 DZFP000879 Harness, LSU N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1944 DZFP000832 Harness, LSU N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1945 DZFP000833 Harness, CSTSEN 1 N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1948 DZFP000836 Harness, Clutch N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1951 DZFP000839 Harness, CRTRIG N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1952 DZFP000840 Harness, Toner/Registration N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1953 DZFP000841 Harness, Paper/UPPER N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1956 DZFP000844 Harness, HTC/ILS/CONT N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1964 DZFP000902 Harness, Fan N - - 1 - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - 1
1964 DZFP000972 Harness, Fan N 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -
19124 DZEC101622 PC Board, ILS N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
19146 HLPVCA1006 Harness 1, LD Extension N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
19147 HLPVCA1007 Harness 2, LD Extension N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
19148 HLPVCA1008 Harness, Motor Extension N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
19 XTB3+8J Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
4N XSN3+W8FC Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
5Y XUC4 E-Clip C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
B9 DZJM000171 Ring, Snap C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
D9 DZPF000001 Nut, M3 C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
E5 XTB3+32J Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
F5 XSN3+5 Screw N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
517
A B C D E F G H I J K
806
1134
1101 1110
8
Fig. 11 Paper Feed Module
518
7.13. Paper Transportion
519
Safety Ref New
Part No. Part Name Note AA AB AC AD AE AF AG AH AJ AK AL AM AN AP AQ AR AS AT AU AV AW ED EE YA YB YC YE YF YG YH YJ YM YN YR YS YT YU YV YW YX YY
Mark No. Parts
1262 DZNE000053 Sheet, Roller N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1263 DZNE000052 Sheet, Plate N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1264 DZNE000051 Sheet,Guide N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1265 DZKN000225 Spring, Pad N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1266 DZJA000790 Plate, Lock N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1267 DZNE000063 Sheet, Guide N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
446 DZJK000006 Clamp, Harness N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1045 DZAL000072 Sensor N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1151 DZLM000052 Bushing, P6L5 Conductive C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1322 DZLM000050 Bushing, P6L8 N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1947 DZFP000897 Harness, Multi SNS 1 N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1948 DZFP000836 Harness, Clutch N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1949 DZFP000837 Harness, Multi SNS 2 N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
19116 DZEC101553 PC Board, SNS N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
19 XTB3+8J Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
23 XYN3+F8 Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1Y XTB3+10J Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
4N XSN3+W8FC Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
B1 DZPB000007 Screw, Silver C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
B9 DZJM000171 Ring, Snap C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
C8 XTW3+8SFC Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
520
A B C D E F G H I J K
1227 19
1204
1220 1208 1
1226 23
1214
23
C8 1236 1225 B9
1234 1235 1211
1228 1045
1230
B1 1206
19 1236
1233 2
1250 1205
23
1251
1221
1252
1224 1235 1218 1251
1219 1255
1249
1231 C8 3
1223 1261
4N
19
C8
1232
1233
1229 1Y 19
1253 19116
4
B9 1266 1247
1222 1232 1248 C8
1151 1203
19 1949
1212
1254 LPC
1231 B9 1947 CN712
1260 446 1201
LPC
1948
CN715 1258 1262 1207 5
1259 19
1151 1245 1322
1244
19
19 B9 1264
1045 1242
1322 1209
1241 1263 1217
6
1265
1239
1202 B9
19 1246
1240 1267
7
1238 1237
19
1238
1947
LPC
CN712 1045 1257 1210
8
Fig. 12 Paper Transportation
521
7.14. Paper Transport Unit
522
A B C D E F G H I J K
19
19 445
1045 1311 1317
1309 1406
19
1977
1304 3
EXFD
CN793
/ 794
19 1305
445 1321
4
19 19 EXFD
19 19
CN792
1310 1045 1518
1323
19
445 1313
19 1326
EXFD EXFD 5
CN791 933 CN794 1977
1320
19 1513
1518
6
1312 1325
19131
EXFD 1518
1308
1978
CN790
1320 1321 7
1303
CN791 CN792
1313
1977 1977
CN794 CN793 1302
1513 1315
1518 1524
1301 8
Fig. 13 Paper Transport Unit
523
7.15. Automatic Duplex Unit
524
A B C D E F G H I J K
1045
937 19 1013 LPC 1518
B9 CN719
1407 LPC 1316
1971 1
CN711 1411
1413 1408
910 1403 1963
1406
1316 1418
1973
B9
1403 2
937
1416
1013 B9
1045
19 1415
941 1518
1404
B9 1411 1316
3
B9
1403
1416
LPC
CN711
941
1150 1045
19 1415 4
1973
B9
1151
1409
1417 5
19 941
1410 1407
1150 937 1412
B9 B9
1151
6
1518 1313
1513
1973
7
1414 1045
1401
1402
8
Fig. 14 Automatic Duplex Unit
525
7.16. Dual-Path Exit Guide Unit
526
A B C D E F G H I J K
B9 937
1013
1009 445
B9
1
19 1507 1502
1012
19
1518
B9
1513
2
1505
1313
1013
1518
1009
19
B9 LPC 1510 3
CN711
1523
937 1503 19
1973 1506
1045 1008
1515
1511
4
1514 19
1509
1524
1509
19
5
1511 1501 19
19 1008
19 36
6
1522
1508
1974
1516 7
1963
1504 1512
1521
LPC
CN719 8
Fig.15 Dual-Path Exit Guide Unit
527
7.17. Inverting Automatic Document Feeder (1/3)
528
Safety Ref New
Part No. Part Name Note AA AB AC AD AE AF AG AH AJ AK AL AM AN AP AQ AR AS AT AU AV AW ED EE YA YB YC YE YF YG YH YJ YM YN YR YS YT YU YV YW YX YY
Mark No. Parts
1943 DZFP000895 Harness, EXT N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
DZEC101552 PC Board, ADF N For ADF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
19115
DZEC101648 PC Board, ADF (iADF) N For iADF 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
19116 DZEC101553 PC Board, SNS N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
19149 DZFP000974 Harness, ADF-FG N 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -
19 XTB3+8J Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
5Y XUC4 E-Clip C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
6A XTB3+12J Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
B1 DZPB000007 Screw, Silver C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
B4 XTB3+8JK Screw, Black C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
B9 DZJM000171 Ring, Snap C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
E8 XTW3+10S Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
F7 XSN4+W10FN Screw, Silver N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
529
A B C D E F G H I J K
1602 19 1045 ADF 1605
CN29
1663 1604
1601 19149
B1 1940
19 1606 1
19
19115
B9 1939
471
E8 ADF 1939 2
CN28
1045
ADF 1939 1612
CN28 1607
B4 19
1653
19116 1609
1614 1610 3
E8 1612
E8
1611
E8
1660 1701
1665
B4 4
1624 1658 5Y
1662
19 1665 19
1660 19 1622 1623
1661 1701 E8
1616
19 19
1654 5
1633
1657
5Y 503
1659
1656
F7 1626
1617
1625 1627
19
1667 6
ADF 6A 1628
B1
19115 CN30 1655
CN21
1943 1629
1935
CN24 CN27 1637 7
1937 1941
1667 1636 1638
CN29 1630 ADF
CN22 CN25 19
1940 1629
1936
19 1666 1635
1635 1938 1939 1634 8
CN25 CN26 CN28 1632 Fig. 16 Inverting ADF (1/3)
530
7.18. Inverting Automatic Document Feeder (2/3)
531
Safety Ref New
Part No. Part Name Note AA AB AC AD AE AF AG AH AJ AK AL AM AN AP AQ AR AS AT AU AV AW ED EE YA YB YC YE YF YG YH YJ YM YN YR YS YT YU YV YW YX YY
Mark No. Parts
1769 DZLF000172 Gear, B42E27 C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1770 DZGB000024 Solenoid N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1771 DZKN000185 Spring, Reversing Guide 1 N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1772 DZJA000685 Bracket, Reversing Guide 1 N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1773 DZJM000422 Adjuster N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1774 DZJM000421 Joint N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1775 DZJA000686 Bracket, Reversing Guide 2 N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1776 DZKN000188 Spring N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1777 DZFC000231 Connector 2 N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1778 DZFC000232 Connector 3 N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1779 DZLF000327 Gear, B18 C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1780 DZJM000430 Lever, Stopper N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1781 DZPG000001 Pin N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1782 DZKN000231 Spring, Hinge Support N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1783 DZJM000477 Stopper, Rubber N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1784 DZKQ000042 Spring, Introduction N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1785 DZJM000491 Film, Reversing Guide 1 N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1786 DZKN000203 Spring, Hinge (Silver, i-ADF) N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1787 DZGA000008 Clutch N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
271 FFPFJ0041 Ring, Snap N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
471 DZJJ000009 Band C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1008 DZLM000109 Bushing, P3.5L5 N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1045 DZAL000072 Sensor N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1260 DZGA000007 Clutch N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1417 DZPK000017 Washer, Polyethylene N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1621 DZJL000115 Bushing C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1622 DZJA000724 Hinge, Arm N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1623 DZJA000727 Plate, Reinforcement N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1624 DZKG000124 Shaft, P6 N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1627 DZLA000080 Roller, Pinch C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1654 DZPA000064 Thumb Screw N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1655 DZJA000730 Bracket, ADF Mounting N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1656 DZMC000713 Cover, Hinge N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1657 DZJA000726 Stopper, Hinge N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1658 DZJM000449 Film, Hinge N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1664 DZJA000725 Base, Left Hinge (A) N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1833 DZMG000018 Latch C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1855 DZGT000007 Brush, Antistatic C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1936 DZFP000889 Harness, AMT N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1938 DZFP000891 Harness, CLT N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1941 DZFP000906 Harness, APNT N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1943 DZFP000895 Harness, EXT N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
19 XTB3+8J Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
24 XYN4+F8 Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
5M XYN3+F4 Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
5Y XUC4 E-Clip C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
5Z XUC6 E-Clip C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
6A XTB3+12J Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
B9 DZJM000171 Ring, Snap C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
532
A B C D E F G H I J K
24 5Y 1936 ADF
1658 CN22
1621
1622 1702 B9
1656 19 1724
1
19 1722
1417 19 271
1624 1260
5Z 19
5Y 1623
1701 1621
1707 1725
1706 1723 1784
1654 1786
1657 1734 1727 2
1782 1730
1711
1701 1943 1731
19 ADF 1045 1627 B9
1664 1705 1045 CN30
1720 1746
5Z 1728
1712
B9 1750 1781 B9
6A 1621 271
1714 19 ADF 1941 1733
1655 1833 1729 3
CN27 1732
1936 1726
ADF 1855
CN22 B9
B9 1736 1735
1716 471
1787 1720
1621 4
1738
1740
1737
B9 1751 1739
1719 1742
1718 1749
1741
1621 1747 B9
1785 19
19 1761
1752 5
1748 1763 1762
1753
1760
5M
1757
19 1777
ADF
CN26
1943 1780 1764 6
1008 1938 19
1750 1779
B9 1768
1621 1833 1767
19 1754 1783
19 1621 1765
1045
1769
ADF 1758 1766 1776
CN30
7
1755 B9
ADF 19 19 1771
CN30 1774 1778
1943 1773 1772
1759 19 1762 5M ADF
1775 CN26
1045 1770
1938
1777 5M 1938
1756 ADF
8
CN26
Fig. 17 Inverting ADF (2/3)
533
7.19. Inverting Automatic Document Feeder (3/3)
534
Safety Ref New
Part No. Part Name Note AA AB AC AD AE AF AG AH AJ AK AL AM AN AP AQ AR AS AT AU AV AW ED EE YA YB YC YE YF YG YH YJ YM YN YR YS YT YU YV YW YX YY
Mark No. Parts
1881 DZKQ000051 Spring, B1 Sensor N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1882 DZJM000496 Film, Guide A N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
271 FFPFJ0041 Ring, Snap N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1008 DZLM000109 Bushing, P3.5L5 N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1045 DZAL000072 Sensor N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1260 DZGA000007 Clutch N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1602 DZJK000045 Clamp, Harness N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1621 DZJL000115 Bushing C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1627 DZLA000080 Roller, Pinch C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1716 DZLF000036 Gear, E25 C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1720 DZJK000046 Clamp, Harness C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1936 DZFP000889 Harness, AMT N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1937 DZFP000890 Harness, DC 3 N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1940 DZFP000893 Harness, B1S N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
19 XTB3+8J Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
24 XYN4+F8 Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
B9 DZJM000171 Ring, Snap C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
535
A B C D E F G H I J K
1831 1806 B9
19
1621 1621 1812
19 1815 1851 1008
1820 1716 1858 1859
B9 1861 1882 1860 4
1819
1820 1621 19
1863
1872
1832
1834
1837 1838 5
1867 19
1830
1864
1621
1833 1838 1873
1877
19 1838 1820
1836 1862
6
19 1835
1832 1843
1880 19 ADF
CN29
1833 1875
1940 1879
1045 1866
1876 19 7
19
1878
1841
1881 1838
1842
1840 8
19 1839
Fig. 18 Inverting ADF (3/3)
536
7.20. PC Boards/ Harnesses
537
Safety Ref New
Part No. Part Name Note AA AB AC AD AE AF AG AH AJ AK AL AM AN AP AQ AR AS AT AU AV AW ED EE YA YB YC YE YF YG YH YJ YM YN YR YS YT YU YV YW YX YY
Mark No. Parts
DZEZ000019 PC Board, SC (DP-3000 PM) 1 - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZEZ000020 PC Board, SC (DP-3000 PQ) - - - - - - - - - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - -
DZEZ000021 PC Board, SC (DP-3000 PS) - - - 1 - - - - - - - - 1 - - - 1 - - - - - - - - - - - - - - - - - - - - - - - -
For DP-3000
DZEZ000022 PC Board, SC (DP-3000 PV) - - - - - - - 1 - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - -
DZEZ000023 PC Board, SC (DP-3000 PX) - - - - - 1 - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZEZ000024 PC Board, SC (DP-3000 PY) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1 - - - - - -
DZEZ000008 PC Board, SC (DP-2500 PU) - - 1 - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - 1
DZEZ000009 PC Board, SC (DP-2500 PT) - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZEZ000012 PC Board, SC (DP-2500 PB) - 1 - - - - - - - 1 - - - - 1 - - - - - - - - - - - 1 - - - - 1 - - - - 1 - - 1 -
DZEZ000013 PC Board, SC (DP-2500 PA) - - - - - - - - - - 1 - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - -
DZEZ000014 PC Board, SC (DP-2500 PE) - - - - - - - - - - - - - - - - - 1 - - - 1 - - 1 1 - 1 - 1 1 - 1 1 - 1 - - 1 - -
DZEZ000015 PC Board, SC (DP-2500 PF) - - - - - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - -
DZEZ000016 PC Board, SC (DP-2500 PG) - - - - - - - - - - - 1 - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - -
DZEZ000017 PC Board, SC (DP-2500 PK) For DP-2500 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1 - - -
DZEZ000018 PC Board, SC (DP-2500 PL) - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - 1 - - - - - - - - - - - -
DZEZ000019 PC Board, SC (DP-2500 PM) 1 - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZEZ000020 PC Board, SC (DP-2500 PQ) - - - - - - - - - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - -
DZEZ000021 PC Board, SC (DP-2500 PS) - - - 1 - - - - - - - - 1 - - - 1 - - - - - - - - - - - - - - - - - - - - - - - -
1983 N
DZEZ000022 PC Board, SC (DP-2500 PV) - - - - - - - 1 - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - -
DZEZ000023 PC Board, SC (DP-2500 PX) - - - - - 1 - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZEZ000024 PC Board, SC (DP-2500 PY) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1 - - - - - -
DZEZ000010 PC Board, SC (DP-2000 PU) - - 1 - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - 1
DZEZ000011 PC Board, SC (DP-2000 PT) - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZEZ000026 PC Board, SC (DP-2000 PB) - 1 - - - - - - - 1 - - - - 1 - - - - - - - - - - - 1 - - - - 1 - - - - 1 - - 1 -
DZEZ000025 PC Board, SC (DP-2000 PA) - - - - - - - - - - 1 - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - -
DZEZ000027 PC Board, SC (DP-2000 PE) - - - - - - - - - - - - - - - - - 1 - - - 1 - - 1 1 - 1 - 1 1 - 1 1 - 1 - - 1 - -
DZEZ000028 PC Board, SC (DP-2000 PF) - - - - - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - -
DZEZ000029 PC Board, SC (DP-2000 PG) - - - - - - - - - - - 1 - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - -
DZEZ000030 PC Board, SC (DP-2000 PK) For DP-2000 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1 - - -
DZEZ000031 PC Board, SC (DP-2000 PL) - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - 1 - - - - - - - - - - - -
DZEZ000032 PC Board, SC (DP-2000 PM) 1 - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZEZ000033 PC Board, SC (DP-2000 PQ) - - - - - - - - - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - -
DZEZ000034 PC Board, SC (DP-2000 PS) - - - 1 - - - - - - - - 1 - - - 1 - - - - - - - - - - - - - - - - - - - - - - - -
DZEZ000035 PC Board, SC (DP-2000 PV) - - - - - - - 1 - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - -
DZEZ000036 PC Board, SC (DP-2000 PX) - - - - - 1 - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZEZ000037 PC Board, SC (DP-2000 PY) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1 - - - - - -
DZEC101737 PC Board, FXB (A) - - 1 - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - 1
DZEC101738 PC Board, FXB (F) 1 1 - 1 - 1 1 1 1 - - 1 1 1 1 1 1 - - 1 - - 1 - - - - - 1 - 1 - - - - - - - 1 - -
1985 N
DZEC101739 PC Board, FXB (G) - - - - 1 - - - - - - - - - - - - 1 - - - 1 - 1 1 - 1 1 - - - 1 1 1 1 1 1 1 - 1 -
DZEC101767 PC Board, FXB (E) - - - - - - - - - 1 1 - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - -
DZEC101901 PC Board, LANB - - - - - - 1 - - - - - - - - - - - - 1 - - 1 - - - - - - - - - - - - - - - 1 - -
1987 N
DZEC101751 PC Board, LANB - 1 1 - - - - - - 1 1 - - - 1 - - - 1 - - - - - - - - - - - - - - - - - - - - 1 -
1989 DZEC101375 PC Board, LANC C - 1 1 - - - 1 - - 1 1 - - - 1 - - - 1 1 - - 1 - - - - - - - - - - - - - - - 1 1 -
1991 DZEC101661 PC Board, PRIF N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
DZEC101321 PC Board, LCE 1 1 - 1 - 1 1 1 1 - - 1 1 1 1 1 1 - - 1 - - 1 - - - - - 1 - - - - - - - - - - - -
DZEC101330 PC Board, LCE - - - - 1 - - - - - - - - - - - - 1 - - - 1 - 1 1 - 1 1 - - - 1 1 1 1 1 1 1 - 1 -
DZEC101716 PC Board, LCE - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1 - -
1994 DZEC101712 PC Board, LCE N - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZEC101714 PC Board, LCE - - - - - - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - -
DZEC101715 PC Board, LCE - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1 - - - - - - - - - -
DZEC101713 PC Board, LCE - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
1995 DZEC101791 PC Board, LCU N - - 1 - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - 1
DZEC101607 PC Board, HTC (100V) - - 1 - 1 - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - 1
1997 N
DZEC101724 PC Board, HTC (200V) 1 1 - 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -
DZEC101755 PC Board, HTC 2 (100V) - - 1 - 1 - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - 1
1998 DZEC101756 PC Board, HTC 2 (200V) N 1 1 - 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -
ETXDN281ABD Low Voltage PSU (100V) - - 1 - 1 - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - 1
1999 ETXDN281EBD Low Voltage PSU (200V) N 1 1 - 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -
538
Safety Ref New
Part No. Part Name Note AA AB AC AD AE AF AG AH AJ AK AL AM AN AP AQ AR AS AT AU AV AW ED EE YA YB YC YE YF YG YH YJ YM YN YR YS YT YU YV YW YX YY
Mark No. Parts
DZEC101753 PC Board, FRM C For PCL6 Emulation Kit 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
19118 DZEC101781 PC Board, FRM (G3B) - - 1 - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - 1
N For 2nd G3 Fax Communication Kit
DZEC101782 PC Board, FRM (G3B) 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 - 1 1 1 - 1 1 1 1 1 1 1 1 1 1 -
19119 DZEC101696 PC Board, EP C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
DZEC101665 PC Board, RLB (100V) - - 1 - 1 - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - 1
19127 N
DZEC101745 PC Board, RLB (200V) 1 1 - 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -
DZEC101686 PC Board, LPC (100V) - - 1 - 1 - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - 1
For DP-2000/3000
19129 DZEC101940 PC Board, LPC (200V) N 1 1 - 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -
DZEC101944 PC Board, LPC (100V) For DP-3000 - - 1 - 1 - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - 1
ETXDN282A4A Optional Low Voltage PSU (100V) - - 1 - 1 - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - 1
19130 N
ETXDN282E4A Optional Low Voltage PSU (200V) 1 1 - 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -
DZFP000921 Harness, HTC2 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
19132 N
DZFP000998 Harness, HTC2 - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZEC101740 PC Board, G3B (K) - - 1 - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - 1
DZEC101741 PC Board, G3B (Q) 1 1 - 1 - 1 1 1 1 - - 1 1 1 1 1 1 - - 1 - - 1 - - - - - 1 - 1 - - - - - - - 1 - -
19134 C
DZEC101742 PC Board, G3B (R) - - - - 1 - - - - - - - - - - - - 1 - - - 1 - 1 1 - 1 1 - - - 1 1 1 1 1 1 1 - 1 -
DZEC101766 PC Board, G3B (P) - - - - - - - - - 1 1 - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - -
19139 DZFP000928 Harness, KEY N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
19142 DZEC101792 PC Board, HCE N 1 1 - 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -
19143 DZFP000943 Harness, HTC/HCE N 1 1 - 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -
19144 DZFP000944 Harness, MAINPOW/HCE N 1 1 - 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -
19145 DZFP000945 Harness, LVPS OP N Countries for 200V 1 1 - 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -
DZFN000050 Cord, Line - - 1 - 1 - - - 1 - - - - - - - - 1 1 - - 1 - 1 1 - 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1
DZFN000104 Cord, Line - - - 1 - - - - - - - 1 - - - 1 1 - - 1 - - - - - - - - - - - - - - - - - - - - -
DZFB000022 Cord, Line 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZFN000042 Cord, Line - - - - - - - - - 1 - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - -
DZFN000043 or Cord, Line - - - - - - - - - 1 - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - -
DZFN000006 or Cord, Line - - - - - - - - - 1 - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - -
DZFN000095 Cord, Line - 1 - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - -
DZFN000015 Cord, Line - - - - - - - - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - -
DZFN000026 or Cord, Line - - - - - 1 - - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - -
19150 N
DZFN000078 or Cord, Line - - - - - 1 - - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - -
DZFN000069 Cord, Line - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZFN000030 Cord, Line - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZFN000017 Cord, Line - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZFN000028 Cord, Line - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZFN000079 or Cord, Line - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZFN000016 Cord, Line - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZFN000096 Cord, Telephone Line - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZFN000114 Cord, Telephone Line - 1 - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - -
DZFN000107 Plug, PTT - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZFB000003 Plug, PTT - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZFB000009 Plug, PTT - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZFB000010 or Plug, AUS - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZFN000108 Plug, PTT - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
19151 N
DZFB000005 Plug, PTT - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZFB000001 Plug, PTT - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - -
DZFB000020 Plug, PTT - - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - -
DZFN000109 or Plug, PTT - - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - -
DZFN000105 Plug, PTT - - - - - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - -
19157 DZEC101683 Harness, CCD 1 N For DP-3000 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
19158 DZEC101947 PC Board, CONS N For DP-3000 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
19159 DZFP001023 Harness, CST2 Extension N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
3006 DZAA001208 Interface Board, IPC N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
539
A B C D E F G H I J K
CN106 CN106 1983 CN110 CN115 CN108 1985 19134 FRM 1987 19119
1915 19158 SC 1918 1923 1908 FXB G3B 19118 LANB EP
CN125 1
1917
CN102
19139
540
7.21. 1-Bin Finisher (1/9)
541
A B C D E F G H I J K
2003
2018
2016
2
2012 2016
2004
2016 2015
2016 2059
2010
2006
3
2007
B1
2008 2016
2063 4
2005
2018
2018
2001 5
2016
2006
2016
2016
2011
2002 2016
2016 2009
2019
2017 7
2005
8
Fig. 20 1-Bin Finisher (1/9)
542
7.22. 1-Bin Finisher (2/9)
543
A B C D E F G H I J K
2112
2111
2110
2107 2
2109
2108
2018
2114 2122 3
2016
2053 2124
2118 2016
2022 2123
2120
2018 2016
2121
4
2124
2105 2103
2023
2126
2020 2113
2117 5
2119
2052 2043
2018
2115
2101 2106
2116
6
2016
2018
2021
2023 2125
7
2104
2113 2102
2016
2043
8
Fig. 21 1-Bin Finisher (2/9)
544
7.23. 1-Bin Finisher (3/9)
545
A B C D E F G H I J K
2204
2018 2060
2060 2210
2215 1
2210 2222
2209
2060 2215
2018
2214
2
2208
2026
2217
2060 2218 3
2210
2060 2212
2215
2213
2101
2028
4
2209
2210 2211
2215 2027
2202
2029 5
2202 2029
2201
2021
2219
2205
6
2221
2216
2021
2203
2018 2018
7
2024
2025
2207
2114 2206
2220
2030 8
Fig. 22 1-B Finisher (3/9)
546
7.24. 1-Bin Finisher (4/9)
547
Safety Ref New
Part No. Part Name Note AA AB AC AD AE AF AG AH AJ AK AL AM AN AP AQ AR AS AT AU AV AW ED EE YA YB YC YE YF YG YH YJ YM YN YR YS YT YU YV YW YX YY
Mark No. Parts
2221 DZJA000752 Frame, Front N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
2222 DZJA000753 Frame, Rear N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
2715 DZLK000019 Belt, Timing N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
548
A B C D E F G H I J K
2329 2040
2058
2048 2058 2058
2062
2328 2337 1
2013 2058 2319
2327 2338
2048 2340 2308
2315 2327 2058
2058
2314
2317 2048 2328
2031 2030 2
2318 2320
2316 2016
2311
2030
2321 2326 2344 3
2311 2321
2343
2322 2326 2303
2308
2058
2062
2222
2304 2057 4
2334
2040 2323 2313
2332 2325
2062
2058 2030 2306
2337 2312 2047
2319 2049 2302
2338 2307 2301
2339 2057
2313 2342 5
2314
2051
2324 2306
2320 2041
2061
2051
2318 2048
2031 2051 6
2318 2314
2301
2344 2051 2305 2320
2309 2048
2306 2051 2051
2341 2302
2331 2330
2042 2715
2335 7
2051 2048
2320 2333
2318 2314
2221 2048
2051 8
2306
Fig. 23 1-B Finisher (4/9)
549
7.25. 1-Bin Finisher (5/9)
550
A B C D E F G H I J K
2420
1
2416
2423
2421 2401
2414 2415
2413
2054
2404 2033
2038 2
2423
2030
2114 2026
2412 2114
2418 3
2419
2030
2417
2403
2422
2424
4
2408 2020
2014
2030
5
2409
2030
2405
2014
2030 6
2114
2407
2411
2406
2114 2032
2030 7
2402
2410 2030
8
Fig. 24 1-B Finisher (5/9)
551
7.26. 1-Bin Finisher (6/9)
552
A B C D E F G H I J K
2055
2506
2510 1
2507
2344
2046 2055
2502
2039 2
2509 2058
2508
2058
3
2058
2039 4
2502
2512
2046
2505
2510
5
2061 2344
2504
2503 6
2030
2511
2501 2114
8
Fig. 25 1-B Finisher (6/9)
553
7.27. 1-Bin Finisher (7/9)
554
A B C D E F G H I J K
2034
2616 2615 2114
2612 2043 2623
2058 2058
2617 1
2617 2638
2602 2034
2058
2616 2603
2037
2057
2614 2624
2
2037
2058 2622
2050
2308 2609
2329
2639
2058 2308
3
2057
2616
2637 2057
2627
2613 2611
2610 2058 2632
2625 2628
2626 2630
2642 2014
2030 2606
7
2035
2607
2030
2630
2030
2608 2607 2014 8
Fig. 26 1-B Finisher (7/9)
555
7.28. 1-Bin Finisher (8/9)
556
A B C D E F G H I J K
2709 1
2705
2701 2719
2712
2057
2114 3
2706
2038
2709 2711 4
2707
2702 2704
2718
2056 2715
5
2716
2714 2710
2717
2038
2703
2045
7
2708
2713
8
Fig. 27 1-B Finisher (8/9)
557
7.29. 1-Bin Finisher (9/9)
558
A B C D E F G H I J K
2014
2802
4
2805
2804
2806
2801
5
2803
6
8
Fig. 28 1-B Finisher (9/9)
559
7.30. Packing and Accessories
560
A B C D E F G H I J K
2907
2914
2920
2906 2908
2913 2918 3
2902
2910
4
19
2905
3701
3306
502 501
5
2905
2917
2905
6A 2905
3701
2915
503 7
8
Fig. 29 Packing and Accessories
561
7.31. 1-Bin Finisher Packing and Accessories
562
A B C D E F G H I J K
2
3002
3002
3006
3
3004
3003
3002
4
3002
3001 8
Fig. 30 1-Bin Finisher Packing
563
7.32. 2nd/3rd/4th Paper Feed Module
564
Safety Ref New
Part No. Part Name Note AA AB AC AD AE AF AG AH AJ AK AL AM AN AP AQ AR AS AT AU AV AW ED EE YA YB YC YE YF YG YH YJ YM YN YR YS YT YU YV YW YX YY
Mark No. Parts
1144 DZLA000203 Roller, Paper Feed N PM 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1145 DZLA000202 Roller, C25 Gear N PM 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1146 DZKQ000029 Spring, A N PM 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1147 DZKQ000030 Spring, B N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1148 DZKQ000028 Spring, C N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1149 DZKN000182 Spring, Roller N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1150 DZLM000006 Bushing, P6L5 C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1151 DZLM000052 Bushing, P6L5 Conductive C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1152 FFPXA74H003C Motor, Lift DC N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1153 DZJM000440 Stopper, Paper Tray N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1154 DZJA000783 Bracket, Ground Plate N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1155 DZKN000227 Spring 1, Ground N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1156 DZKN000228 Spring 2, Ground N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1161 DZJM000474 Sheet, Protection C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1173 DZLM000103 Collar N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1174 DZLM000119 Brush, Feed N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1230 DZFP000747 Resistor, 200M Ohms N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1258 DZLF000325 Gear, B27 N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1259 DZKG000106 Shaft, Clutch N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1260 DZGA000007 Clutch N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1627 DZLA000080 Roller, Pinch C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1965 DZFP000859 Harness, CST2 N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1966 DZFP000860 Harness, CLUTCH N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1967 DZFP000861 Harness, Paper/UPLIMIT N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1968 DZFP000862 Harness, Feed Sensor N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1969 DZFP000863 Harness, Paper Tray Sensor N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1970 DZFP000864 Harness, Jam Sensor N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1981 DZFP000865 Harness, CST3 N For DP-2000/2500 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
DZFP001000 Harness, CST3 For DP-3000 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1982 DZFP000899 Harness, PM Motor N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
DZEC101609 PC Board, CST2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
19123 N
DZEC101946 PC Board, CST2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
DZEC101606 PC Board, CST3 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
19133 N
DZEC101965 PC Board, CST3 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
19160 DZFP001024 Harness, CST3 Extension N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
19 XTB3+8J Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1Y XTB3+10J Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
4N XSN3+W8FC Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
5Y XUC4 E-Clip C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
B1 DZPB000007 Screw, Silver C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
B9 DZJM000171 Ring, Snap C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
565
A B C D E F G H I J K
B9 1150
B9 1150
3112 1966
19123 B9 19
19 CST3 CST2
3106
19 1129 CST2 19
CN806 CN773 CST3 CST3 CN773
19133 1260 1147 1260 1
CN800 CN806 1Y
1967 CST2 3103 3104
1966 1258 CN775 1150
1259 3105
3122 1150 1133
411 CST3 CST2
446 1141 CN800 CST2 CST2 CN803
3121 CST2 CN778 CN776
19 CN775 CST3 1970 1045 19
1045 CN802
1968 2
413 1967 1045
1045 B9
1174
1137 19
19
1142
B1 1110 1151 19
3123 3117 3102
B9 1148
3
1173
3101
3108 1151
913 1135
1144
941 1128
3113 555
19
937 19 4
19 1136
1134
B9 19
19 936 1627 1145
3115 1132
3114 1969 3116 3111
B9 1127
908 1161 3109 3107
3108
937 5
CST2 19
CN777 1181
3120 CST3 1045 19 1138
CN801
1982 5Y
3124
SCT3 936 1143
CN805 1131
SCT2
1152 19 1156 1139
CN774 1145
SCT3
917 CN804 1146 6
937 4N
3118 3119 1154 1230 1132
B9 3126 1149
B9 1155
B9 19
3124 1151
566
7.33. ADF Packing and Accessories
567
A B C D E F G H I J K
2907
1657
1
3308
3301
2
1636 3308 6A 19
3302
3302
3304
3308 3303
3
B5 1654
1656 4
1655 503
3302
3302
5
1655
1656
3306 3305
6
8
Fig. 33 ADF Packing and Accessories
568
7.34. Automatic Document Feeder (1/3)
569
Safety Ref New
Part No. Part Name Note AA AB AC AD AE AF AG AH AJ AK AL AM AN AP AQ AR AS AT AU AV AW ED EE YA YB YC YE YF YG YH YJ YM YN YR YS YT YU YV YW YX YY
Mark No. Parts
6A XTB3+12J Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
B1 DZPB000007 Screw, Silver C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
B4 XTB3+8JK Screw, Black C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
B9 DZJM000171 Ring, Snap C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
E8 XTW3+10S Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
F7 XSN4+W10FN Screw, Silver N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
570
A B C D E F G H I J K
1605
19
1604
3401
19149
B1 19 1606 1
19115
B9
1939
E8 ADF 1939 2
CN28
ADF 1045
CN28
1939 1612
B4 19 1607
1653
1609
19116 3
E8 1610
1612
1614
1611
1660 1701 E8 E8
1665
B4 4
1624 1658 5Y
1662
19 1665 19
1660 19 1623
1622
1661 1701
19 19
1654 5
1633
1657
5Y 503
1659
1656 E8 1616
F7 1626
1627
1625
19
6
1667
ADF 6A 1628 B1
19115 1655
CN30 1629
CN21 1942
1935
CN27 1637 7
1941
1667 1636 1638
CN29 1630 ADF
CN22 CN25 19
1940 1629
1936
19 1666 1635
1635 1939 1634 8
CN25 CN28 1632 Fig. 34 ADF (1/3)
571
7.35. Automatic Document Feeder (2/3)
572
Safety Ref New
Part No. Part Name Note AA AB AC AD AE AF AG AH AJ AK AL AM AN AP AQ AR AS AT AU AV AW ED EE YA YB YC YE YF YG YH YJ YM YN YR YS YT YU YV YW YX YY
Mark No. Parts
1750 DZKN000209 Spring, Latch N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1751 DZLA000209 Roller, Exit N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1753 DZLA000208 Roller, Feed 2 N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1758 DZKR000019 Spring, Sensor B2 N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1759 DZHC000104 Actuator, Sensor B2 N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1761 DZJA000679 Bracket, Solenoid N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1764 DZJM000432 Cover, Gear Bracket N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1765 DZLF000015 Gear, B44 C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1766 DZKN000006 Coil Spring, Idle Gear C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1767 DZJM000431 Plate, Moving Gear N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1768 DZJA000697 Bracket, Moving Gear N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1769 DZLF000172 Gear, B42E27 C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1772 DZJA000685 Bracket, Reversing Guide 1 N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1773 DZJM000422 Adjuster N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1776 DZKN000188 Spring N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1779 DZLF000327 Gear, B18 C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1780 DZJM000430 Lever, Stopper N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1781 DZPG000001 Pin N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1782 DZKN000231 Spring, Hinge Support N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1783 DZJM000477 Stopper, Rubber N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1784 DZKQ000042 Spring, Introduction N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1787 DZGA000008 Clutch N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1820 DZLF000332 Gear, E18 Drive N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1833 DZMG000018 Latch C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1936 DZFP000889 Harness, AMT N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1941 DZFP000906 Harness, APNT N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1942 DZFP000894 Harness, B2S N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
19 XTB3+8J Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
24 XYN4+F8 Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
5Y XUC4 E-Clip C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
5Z XUC6 E-Clip C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
6A XTB3+12J Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
B9 DZJM000171 Ring, Snap C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
573
A B C D E F G H I J K
24 5Y 19 1621
1658 B9
1702 1722 1936 ADF
1622
1656 CN22
1724 1
19
19 3501
1624 1417 1727
5Y 5Z 19 271
1623
1701 1260
1707
1706 1725 1621
1654 3507
1784
1657 1782 2
1711 1942
1701 1045 1730
19 ADF
1664 1045 CN30 1731
5Z 1705 B9
1712 1720
1746
1728
1750 ADF 1941
1621
6A 1714 CN27
1781 B9
1833 19 271 3
1655
1820 1729 1733
ADF 3504 1726 1732
CN22 1621
1736
1936
B9 1720 19
B9 1716 B9 4
ADF
CN30 1737
1787
1045
B9 3502 1621
1942
3508 B9 1621
1738
1740 1758
19 5
1739 1761
1718 1742 1759
1751 1741
1747 B9
3503
19 1748 19
3505 6
1780 1764
1008 19
1750 1779 1768
1833
1783
19 1765 1776
7
3506 1766
1621 1769
1767
B9 1772
B9
19
1753 1621 19
1621 1773
3509
3510 8
1820
Fig. 35 ADF (2/3)
574
7.36. Automatic Document Feeder (3/3)
575
A B C D E F G H I J K
1602 19 ADF
1045 CN29
19 3601
1663
ADF 1940 1
CN22
1936 1855
1602
1801
3604 3602
1720
2
24 1621 1849
3603
3606
1814 3
1627
1831 3605
1850
B9 19
1806 1812 19
1815
1807 1867
1716 1882
B9 4
1861
19
1832 1837
1834
1830
1866 1864 5
1838
1863 1862
1833
19 1843
1836
ADF
1835 CN29
19 6
1832
1940
1880
19
1045
1833
1838
19
7
1841
1842
1881
1840
1839
19
8
Fig. 36 ADF (3/3)
576
7.37. PCL6 Emulation Kit
577
A B C D E F G H I J K
3701
3702 1
3703
2
3704
308 19
3308
3306 3
3706
8
Fig. 37 PCL6 Emulation Kit
578
7.38. 10/100 Ethernet Interface/Internet Fax Kit
579
A B C D E F G H I J K
3701
3802
1
3801
305
3306
3
3803
19
4
3804
3706
3308
1987
1916
5
445
8
Fig. 38 10/100 Ethernet Interface/Internet Fax Kit
580
7.39. Fax Communication Kit
581
Safety Ref New
Part No. Part Name Note AA AB AC AD AE AF AG AH AJ AK AL AM AN AP AQ AR AS AT AU AV AW ED EE YA YB YC YE YF YG YH YJ YM YN YR YS YT YU YV YW YX YY
Mark No. Parts
DZSD001208 Operating Instructions - - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - -
(For FAX DP2000 AS)
DZSD001209 Operating Instructions - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - -
(For FAX DP2000 AN)
DZSD001210 Operating Instructions - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
(For FAX DP2000 AD)
DZSD001211 Operating Instructions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1 - - - - - -
3902 N
(For FAX DP2000 YS)
DZSD001212 Operating Instructions - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
(For FAX DP2000 AE)
DZSD001213 Operating Instructions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1 - - -
(For FAX DP2000 YV)
DZSD001215 Operating Instructions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
(For FAX DP2000 YJ)
3903 DZSM000306 Install Guide, FXB OP(AU) N 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1
DZNK003049 Label, TA (For FAX AU) - - 1 - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - -
DZNK003285 Label, TA (For FAX AG) - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZNK003532 Label, TA (For FAX YW) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1 - -
DZNK003533 Label, TA (For FAX YR) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1 - - - - - - -
DZNK003392 Label, TA (For FAX YX) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1 -
DZNK003518 Label, TA (For FAX AE) - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
3904 DZNK003227 Label, TA (For FAX AL) N - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZNK003238 Label, TA (For FAX AW) - - - - - - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - -
DZNK003487 Label, TA (For FAX YV) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1 - - -
DZNK003457 Label, TA (For FAX AK) - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZNK003519 Label, TA (For 2nd G3 FAX AE) - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZNK003239 Label, TA (For 2nd G3 FAX AW) - - - - - - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - -
DZNK003479 Label, TA (For 2nd G3 FAX YV) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1 - - -
3905 DZRJ000021 Bag, Polyethylene N 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1
DZSH000136 Seat,RTTE Declaration 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZSH000137 Seat,RTTE Declaration - 1 - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - -
DZSH000138 Seat,RTTE Declaration - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZSH000139 Seat,RTTE Declaration - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZSH000140 Seat,RTTE Declaration - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZSH000141 Seat,RTTE Declaration - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZSH000142 Seat,RTTE Declaration - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
3906 DZSH000143 Seat,RTTE Declaration N - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZSH000144 Seat,RTTE Declaration - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZSH000145 Seat,RTTE Declaration - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZSH000146 Seat,RTTE Declaration - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - -
DZSH000147 Seat,RTTE Declaration - - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - -
DZSH000148 Seat,RTTE Declaration - - - - - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - -
DZSH000149 Seat,RTTE Declaration - - - - - - - - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - -
DZSH000150 Seat,RTTE Declaration - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1 - - - - - - - - - - - -
DZNA000720 Sheet, MODE (English) - 1 1 1 - 1 - 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 1 1 - 1 1 1 - 1 1 1 1 1 1 1 - 1 1 1
DZNA000723 Sheet, MODE (German) 1 - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
For DP-2000,
132 DZNA000724 Sheet, MODE (Chinese) N - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1 - - -
Fax Communication Kit
DZNA000722 Sheet, MODE (French) - - - - - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - -
DZNA000725 Sheet, MODE (Taiwanese) - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZNK002797 Label 1, Line 1 - - 1 - 1 - - - - - - - - - - - - 1 1 - - 1 - 1 1 - 1 1 - - - 1 1 1 1 1 1 1 1 1 1
DZNK003056 Label 1, Line 1 (AW) - - - - - - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - -
301 DZNK003084 Label 1, Line 1 (AK) N For Fax Communication Kit - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZNK003085 Label 1, Line 1 (AG) 1 - - 1 - 1 1 1 1 - 1 1 1 1 - 1 1 - - 1 - - 1 - - - - - 1 - 1 - - - - - - - - - -
DZNK003100 Label 1, Line 1 (AB) - 1 - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - -
429 DZKP000196 Bracket, Speaker N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1
448 DZDR000001 Speaker C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1
481 DZNK003066 Seal, Circuit N - - 1 - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - -
1917 DZFP000911 Harness, SPK 2 N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1
DZFP000880 Harness, LCU 1 1 - - 1 - 1 - 1 1 1 1 1 1 1 - 1 1 - - 1 1 - 1 - - - - - 1 - 1 - - - - - - - - - -
1919 N
DZFP000956 Harness, LCU 1 - 1 1 - 1 - 1 - - - - - - - 1 - - 1 1 - - 1 - 1 1 - 1 1 - - - 1 1 1 1 1 1 1 1 1 1
582
Safety Ref New
Part No. Part Name Note AA AB AC AD AE AF AG AH AJ AK AL AM AN AP AQ AR AS AT AU AV AW ED EE YA YB YC YE YF YG YH YJ YM YN YR YS YT YU YV YW YX YY
Mark No. Parts
DZEC101737 PC Board, FXB (A) - - 1 - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - 1
DZEC101738 PC Board, FXB (F) 1 1 - 1 - 1 1 1 1 - - 1 1 1 1 1 1 - - 1 - - 1 - - - - - 1 - 1 - - - - - - - 1 - -
1985 N
DZEC101739 PC Board, FXB (G) - - - - 1 - - - - - - - - - - - - 1 - - - 1 - 1 1 - 1 1 - - - 1 1 1 1 1 1 1 - 1 -
DZEC101767 PC Board, FXB (E) - - - - - - - - - 1 1 - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - -
DZEC101321 PC Board, LCE 1 1 - 1 - 1 1 1 1 - - 1 1 1 1 1 1 - - 1 - - 1 - - - - - 1 - - - - - - - - - - - -
DZEC101330 PC Board, LCE - - - - 1 - - - - - - - - - - - - 1 - - - 1 - 1 1 - 1 1 - - - 1 1 1 1 1 1 1 - 1 -
DZEC101716 PC Board, LCE - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1 - -
1994 DZEC101712 PC Board, LCE N - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZEC101714 PC Board, LCE - - - - - - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - -
DZEC101715 PC Board, LCE - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1 - - - - - - - - - -
DZEC101713 PC Board, LCE - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
1995 DZEC101791 PC Board, LCU N - - 1 - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - 1
DZFN000050 Cord, Line - - 1 - 1 - - - 1 - - - - - - - - 1 1 - - 1 - 1 1 - 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1
DZFN000104 Cord, Line - - - 1 - - - - - - - 1 - - - 1 1 - - 1 - - - - - - - - - - - - - - - - - - - - -
DZFB000022 Cord, Line 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZFN000042 Cord, Line - - - - - - - - - 1 - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - -
DZFN000043 or Cord, Line - - - - - - - - - 1 - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - -
DZFN000006 or Cord, Line - - - - - - - - - 1 - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - -
DZFN000095 Cord, Line - 1 - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - -
DZFN000015 Cord, Line - - - - - - - - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - -
DZFN000026 or Cord, Line - - - - - 1 - - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - -
19150 N
DZFN000078 or Cord, Line - - - - - 1 - - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - -
DZFN000069 Cord, Line - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZFN000030 Cord, Line - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZFN000017 Cord, Line - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZFN000028 Cord, Line - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZFN000079 or Cord, Line - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZFN000016 Cord, Line - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZFN000096 Cord, Telephone Line - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZFN000114 Cord, Telephone Line - 1 - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - -
DZFN000107 Plug, PTT - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZFB000003 Plug, PTT - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZFB000009 Plug, PTT - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZFB000010 or Plug, AUS - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZFN000108 Plug, PTT - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
19151 N
DZFB000005 Plug, PTT - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZFB000001 Plug, PTT - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - -
DZFB000020 Plug, PTT - - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - -
DZFN000109 or Plug, PTT - - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - -
DZFN000105 Plug, PTT - - - - - - - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - -
DZQE000003 Rosett - - - - - - - - - 1 - - - - - - - - - - - 1 - 1 1 - - 1 1 - - 1 1 1 1 - 1 1 - - 1
19152 N
DZQE000005 Rosett - - - - - - - - - - - - - 1 - - - - - - - - - - - - - - - - - - - - - - - - - - -
3306 DZRJ000020 Bag, Protective N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
3308 DZRJ000029 Plastic Bag N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
3701 DZRJ000002 Bag, Polyethylene N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
3706 DZRB000101 Carton Box N 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
3803 DZRJ000003 Bag, Polyethylene N - 1 1 - - - 1 - - 1 1 - - - 1 - - - 1 1 - - 1 - - - - - - - - - - - - - - - 1 1 -
19 XTB3+8J Screw C 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
583
A B C D E F G H I J K
3701
3903 1
3906
3901
3306 481
1994 132
1995
3904
3902
301
1985 3
3803
429
19
1917
5
19150 19151
19152
8
Fig. 39 Fax Communication Kit
584
7.40. Parallel Port Interface Kit
585
A B C D E F G H I J K
1
3701
4001
3306
3703
2
4002
3
3706
3803
1922 4
5
1923
8
Fig. 40 Parallel Port Interface Kit
586
7.41. Stands for USA
587
A B C D E F G H I J K
4106 4106
F8 F8
1
4105 4105
F8 F8
4104 4104
2
F8
F8
4102 4102
3
4103
4103
4109
4106
F8
5
4105
F8
4104
6
F8 4107
4102 4102
4103
7
4101
4109 F8
4102
4101
4107
4109
8
Fig. 41 Stands for USA
588
8 Installation
8.1. Precautions During Set Up
Copy machine performance and the copy quality is subject to and dependant on environmental conditions.
To maintain good performance, quality, and safe operation, observe the following precautions:
1. For safe operation and to avoid trouble, do not install the system under the following conditions:
2. The weight of machine is 220 lb (100 kg) or more with options. It must be installed on a firm and leveled
surface.
3. The maximum power consumption is 1.4 kW. Use a dedicated power supply of 120 VAC and 12 A
(220-240 VAC and 6 A) or higher. (Do not use an extension cord)
4. Make sure the outlet is properly grounded. (Do not ground to gas or water pipe)
8.2. Unpacking
Visually check the condition and contents of the box for completeness or any shipping damage before
installation.
Remove all filament tapes used to secure the Fuser and Process Units during shipment.
Note 1:
Refer to each individual Installation Guide when installing Stands or other Optional Kits.
Note 2:
The following machine illustrations, depicts a DP-2000 with a standard configuration of 1 Paper Tray.
The DP-2500/3000 standard configuration is 2 Paper Trays.
589
8.3.1. Installation Procedure
(1) Remove 3 Screws.
(1) (2) Remove the Left Platen Cover.
(2)
(3), (5)
(4)
590
(6) Re-install the Left Platen Cover and fasten with 3
(6) Screws removed in step 1.
(7) Put the shipping metal bracket removed in step 4
in the space provided in the Paper Tray.
(8) Pull out the insulation film from the Battery
(8) Holder.
(7)
(9)
(10)
591
(11) Open the Front Cover, pull out the rails and
install the Process Unit.
(11) (12) Line up the holes under the rails with the
mounting holes under the Process Unit and
install the 2 Screws (included with the Process
Unit) to act as a stopper.
(12) Note:
Ensure that the screws recess into the rail
holes in order for the Process Unit to
smoothly slide on the rails.
(12) (12)
(13)
(14)
(15)
Connect the Power Cord and turn the Power Switch ON.
Note:
Set the parameter for F5-73 (PM (OPC DRUM)) and/or F5-74 (PM (PROCESS UNIT)) to “User” if the
replacement will be done by the user.
592
8.4. Adjustment
8.4.1. Exposure (Standard Adjustment)
The following values will be added to the reference value. DO NOT adjust these codes in the field.
F6-18 : Laser power compensation
F6-19 : Developer bias standard voltage compensation
1. Enter F6 mode.
2. Ensure that F6-18 and 19 are set to “0”.
3. Enter F2 mode and set the exposure to the center position.
Set the machine to Text / Photo mode.
4. Make a copy of Test Chart 53/54 with gray scale (P/N FQ-SJ1011).
a. Gray scale “1” should not be visible.
b. Gray scale “2” should be clearly visible.
A
1 Not visible
2 Clearly
visible
3
Note:
Skip to step (10) if the density is within specification.
5. Enter F6-50 mode.
6. Enter the new content.
Note:
The “Reset” key is used to enter the “-” content.
(+) : Lighter side
(-) : Darker side
7. Press the “OK” key, then press “Cancel” key.
8. Enter F2 mode.
9. Make a copy to confirm the adjustment.
Note:
Repeat Step (3) to (9) until proper density is attained.
F6-49 : Text mode
F6-51 : Photo mode
10. Press “Function” and “Clear” keys simultaneously to exit the service mode.
1. Press “Function”, “Ledger / A3 of Original Size”, and “3” keys simultaneously to enter the service mode.
2. Enter F6-05 mode.
3. Enter the new content.
Note:
The “Reset” key is used to enter the “-” content.
(+) : Paper feed timing is delayed.
(-) : Paper feed timing is advanced.
4. Press the “OK” key, then press “Cancel” key.
5. Enter F2 mode.
6. Make a copy to confirm the adjustment. Perform Step (3) again, if necessary.
7. Press “Function” key and “Clear” keys simultaneously to exit the service mode.
593
8.4.3. Lead Edge Registration Adjustment (ADU)
For DP-2000
594
For DP-2500/3000
595
9 Options and Supplies
9.1. Installing the Electronic Sorting Board (DA-ES200) [For DP-2000 only]
9.1.1. Contents
9.1.2. Installation
Note:
Turn the Power Switch to the OFF (O) position and unplug the AC Power Cord before
beginning installation.
(1)
(3)
(2)
(5)
(4)
x7
596
9.2. Installing the Fax Communication Kit (DA-FG230)
9.2.1. Contents
(1)
(3)
(2)
597
(4) Remove 7 Screws.
(5) Open the Rear Plate as illustrated on the left.
(5)
(4)
x7
(6)
598
(12) Connect the SPK2 Harness to CN125 located on
(12)
the upper right hand side of the SC PC Board.
Caution:
Connecting the Speaker into Connector
CN118 will damage the SC PC Board.
(13) Place the SPK2 Harness into the 2 clamps.
(13)
(15)
(16)
(17)
599
(18) Connect the LCU1 Harness from the FXB PCB
to CN25 on the LCU/LCE PC Board.
(19) Install the LCU/LCE PC Board to the Rear Plate.
(20) Secure the LCU/LCE PC Board with 2 Screws.
(20)
(18) (19)
(22)
(23)
600
< For DP-2000 only >
(27) (26) (26) Paste the Fax Function Label on the Automatic
Document Feeder or the Platen Cover as shown
below.
(0.2 in., 5 mm)
(27) (26)
601
9.3. Installing the 2nd G3 Fax Communication Port Kit (DA-FG231)
9.3.1. Contents
(1)
(3)
(2)
(5)
(4)
x7
602
(6) Connect the G3B Harness to CN132 on the G3B
(8) PC Board.
(7) (7) Insert the Harness Clamp into the mounting hole
on the G3B PC Board.
(8) Place the G3B Harness into the Harness Clamp.
(6)
(10)
(14)
(12) (13)
(16)
(17)
603
(18) Break off the LINE protective tab on the Left
Rear Cover only.
(19) Proceed with the installation of other options.
If finished, secure the Rear Plate and re-install
(18)
(13) the remaining Covers.
604
9.4. Installing the 10/100 Ethernet Interface / Internet Fax Kit (DA-NE200)
9.4.1. Contents
(1)
(3)
(2)
605
(4) Remove 7 Screws.
(5) Open the Rear Plate as illustrated on the left.
(5)
(4)
x7
(8)
(10)
(11)
606
(12) Connect the LANB-LANC Harness to CN200 on
(15) the LANC PC Board.
(13) Install the LANC PC Board to the Rear Plate.
(12) (14) Secure the LANC PC Board with 1 Screw.
(15) Place the LANB-LANC Harness into the Harness
Clamp.
(14)
(13)
(17)
607
9.5. Installing the Handset Kit (UE-403171/UE-403172) and
the Handset Mounting Kit (UE-408004-AU)
9.5.1. Contents
< UE-403171/UE-403172 >
(1)
608
(2) Hook the projections of the Cradle Assembly into
the holes on the Left Side Cover.
(3) Connect the cable from the Cradle Assembly to
(3) the Handset Jack of the LCU/LCE PC Board on
the rear of the machine.
(2)
(1)
609
(6) Position the Mounting Bracket 3 as illustrated on
the left.
(7) (7) Secure the Mounting Bracket 3 with 2 Screws
(XTB3+8J).
(6) (8) Re-install the Left Side Cover.
(10)
(11)
(12)
(14)
610
(16) Re-install the 1-Bin Finisher and the Latch
(17) Catcher.
(17) Hook the projections of the Cradle Assembly into
the mounting holes on the Mounting Bracket 1.
(18) Connect the cable from the Cradle Assembly to
the Handset Jack of the LCU/LCE PC Board on
the rear of the machine.
(18)
611
9.6. Installing the Parallel Port Interface Kit (DA-PC200)
9.6.1. Contents
(1)
(3)
(2)
(5)
(4)
x7
612
(6) Remove 1 Screw.
(7) Remove the PRIF Plate.
Note:
The PRIF Plate will not be needed after
installing the Parallel Port Interface.
(7)
(6)
613
9.7. Installing the PCL6 Emulation Kit (DA-PC210)
9.7.1. Contents
(1)
(3)
(2)
(5)
(4)
x7
614
When the Parallel Port Interface Kit has already
been installed
(8) (6) Remove 1 Screw.
(7) Remove the PRIF Assembly.
(7) (8) Disconnect the PRIF Harnesses on the PRIF PC
Board.
(6)
615
9.8. Installing the Sorting Image Memory 8/16/128 MB
(DA-SM08B/16B/28B)
9.8.1. Contents
9.8.2. Installation
Note:
Turn the Power Switch to the OFF (O) position and unplug the AC Power Cord before
beginning installation.
(1)
(3)
(2)
(5)
(4)
x7
For DP-2000
(6) Remove 2 Screws.
(7) Release the Locking Spacer.
(8) Remove the SORT PC Board.
(8) (6)
(7)
616
(9) Insert the SDRM PC Board into the SORT
MEMORY socket on the SORT PC Board as
illustrated on the left.
(9) Note:
Make sure to insert the SDRM PC Board with
20 - 30° angle against the memory socket,
and then lock it down.
(10) Re-install the SORT PC Board.
(10)
For DP-2500/3000
(11) Insert the SDRM PC Board into the SORT
MEMORY socket on the SC PC Board as
illustrated on the left.
Note:
Make sure to insert the SDRM PC Board with
(11) 20 - 30° angle against the memory socket,
and then lock it down.
(12) Proceed with the installation of other options.
If finished, close and secure the Rear Plate and
re-install the remaining Covers.
617
9.9. Installing the Expansion Flash Memory Card 4/8 MB (UE-410047/410048)
9.9.1. Installation
Note:
Turn the Power Switch to the OFF (O) position and unplug the AC Power Cord before
beginning installation.
(1)
(3)
(2)
(4)
4FLASH
MB
618
9.10. Installing the Platen Cover (DA-UC200)
9.10.1. Contents
9.10.2. Installation
(1) Install the 2 Platen Hinges.
(2) (1) (2) Secure the Platen Hinges with 2 Screws each.
(2)
(1)
619
9.11. Installing the Automatic Document Feeder and
the Inverting Automatic Document Feeder (DA-AS200/AR250)
9.11.1. Contents
(2)
(2)
620
(4) Install the Automatic Document Feeder on top of
the ADF Mounting Brackets.
(4)
Note:
a. Set the Automatic Document Feeder in the
direction of the arrow.
b. Align the hallmark on the right side of the
Hinge Base and the ADF Mounting Bracket
as illustrated on the left.
(5)
(5) Tighten the 2 Thumb Screws (Silver).
(6) Secure the Automatic Document Feeder with 2
(7) (6) Screws. (XSN4+W10FN Silver)
(7) Install 1 Screw on the back of the left ADF
Mounting Bracket from the bottom. (XTB3+8J)
(8) Remove 1 Screw.
(9) Remove the CN Bracket.
(9)
(8)
(10)
(11)
For European Models Only
621
(12) Re-install the CN Bracket.
(13) Secure the CN Bracket with 1 Screw.
(12)
(13)
Skewed to
the right
622
(16) Check for spacing between the ADF Unit and the
Scanning Glass Guide as illustrated on the left.
Space
ADF Unit
Scanning Glass
Guide
Scanning Glass
(18) (19)
(20)
623
(21) Peel off the 6 adhesive protectors from the
Scanning Pad.
(23)
(22) Place the Scanning Pad on the glass aligning on
1mm the upper left corner, keeping 1mm space as
shown on the left.
(22) (23) Close the Automatic Document Feeder.
Note:
Re-open the ADF Unit and push the Scanning
Pad gently to paste it properly.
(21)x6
(25)
624
Printed Adjustment Adjustment
Document Image Amount Remarks
No.90 0.1mm
A After Parameter
ADF detection 1 Point Setting, reboot
timing
(Adjustment of
ADF image
read start position)
Paper
Travel
A 0.1mm
the machine
to enable the
Parameter
Setting.
A 1 Point
No.91 0.2mm
ADF original
1 Point
lead edge
registration Shadow of
Document
(Adjustment of 0.2mm
Paper Leading Edge
original detection Travel
timing) 1 Point
Void
No.93 0.2mm
No.94 0.1%
ADF Reduced
magnification 1 Point
ratio (Top feed)
(Adjustment of 0.1%
ratio when the Enlarged
scan is made) 1 Point
625
9.12. Installing the Stand for 1-Paper Tray Configuration (DA-DA200-PA)
Note:
This option is available only for certain countries.
9.12.1. Contents
9.12.2. Installation
Note:
Turn the Power Switch to the OFF (O) position and unplug the AC Power Cord before
beginning installation.
(1)
(2)
626
(4) Slide out the Paper Tray from the machine.
(7) Joint E Plate
(5) Open the Front Cover.
(6) Joint B Plate (6) Join the Desk for 1st Feeder Unit and the
machine with the Joint A Plate (FR), Joint B
(7)
Plate (RR), Joint D Plate (FL) and Joint E Plate
(6) (RL).
(7) Secure the Joint A Plate, Joint B Plate, Joint D
(6)
Plate and Joint E Plate with 4 Screws.
(7)
(8) Close the Front Cover and re-install the Lower
Joint D
Plate Rear Cover.
(4) (9) Slide the Paper Tray into the machine.
(6) (10) Set the machine with the 4 Adjusters as
(5) illustrated on the left.
Joint A Plate
(7)
(10)
627
9.13. Installing the Stand for 2-Paper Tray Configuration (DA-DA210-PA)
Note:
This option is available only for certain countries.
9.13.1. Contents
9.13.2. Installation
Note:
Turn the Power Switch to the OFF (O) position and unplug the AC Power Cord before
beginning installation.
(1)
(2)
628
(4) Slide out the Paper Tray from the machine.
(7) Joint E Plate
(5) Open the Front Cover.
(6) (6) Join the Medium Cabinet and the machine with
Joint B Plate the Joint A Plate (FR), Joint B Plate (RR), Joint D
(7) Plate (FL) and Joint E Plate (RL).
(7) Secure the Joint A Plate, Joint B Plate, Joint D
(6)
Plate and Joint E Plate with 4 Screws.
(8) Close the Front Cover and re-install the Lower
(6) (7) Rear Cover.
Joint D (9) Slide the Paper Tray into the machine.
Plate
(10) Set the machine with the 4 Adjusters as
(4)
illustrated on the left.
(6)
(5)
Joint A Plate
(7)
(10)
629
9.14. Installing the 3rd Paper Feed Module and the Stand for 3-Paper Tray
Configuration (DA-DS210/DS215, DA-DA220-PA)
9.14.1. Contents
9.14.2. Installation
Note:
1. DA-DS210 is installed only on the DP-2000/2500.
2. Turn the Power Switch to the OFF (O) position and unplug the AC Power Cord before
beginning installation.
(1)
630
(2) Remove 2 Screws (Silver).
(2)
Note:
The number of screws may vary on units
produced prior to Dec. 2000.
(3) Remove the Lower Rear Cover.
(4) Slide out the Paper Tray.
(3)
(4)
(5) (5) Join the Short Cabinet and the 3rd Paper Feed
(6) Joint E Plate Module with the Joint A Plate (FR), Joint B Plate
Joint B Plate (RR) and Joint E Plate (RL).
(6) Secure the Joint A Plate, Joint B Plate and Joint
(6) E Plate with 3 Screws.
(9)
Front Cover
(11)
631
(12) Remove 2 Screws (Silver).
(12) Note:
The number of screws may vary on units
produced prior to Dec. 2000.
(14) (13) Remove the Lower Rear Cover.
(14) Slide out the Paper Tray from the machine.
(13)
(15)
(15) (16)
(16) (15)
(22)
(21)
632
9.15. Installing the 2nd/4th Paper Feed Module (DA-DS200) [For DP-2000/2500
Only] and the Stand for 4-Paper Tray Configuration (DA-DA230-PA)
9.15.1. Contents
(1)
(2)x4
(3)
633
(4) Slide out 2 Paper Trays.
(6)
(5) Install the 4 Brackets.
(6) Secure the 4 Brackets with 8 Screws.
(5)
(4) (6)
(6) (5)
9.15.3. Installing the 3rd and 4th Paper Feed Modules on the DP-2000/2500
Note:
Turn the Power Switch to the OFF (O) position and unplug the AC Power Cord before
beginning installation.
(1) Slide out the Paper Tray from the 2nd/4th Paper
Feed Module.
(2) Place the 2nd/4th Paper Feed module on top of
(3) the Caster.
Note:
The side with the silver seal shown in (a) on
the left is the front.
(3) Place the 3rd Paper Feed Module on the 2nd/4th
Paper Feed Module.
FRONT (1)
FRONT
(a)
634
(4)x4 (4) Remove 4 Screws (Silver).
Note:
The number of screws may vary on units
(6) produced prior to Dec. 2000.
(5) Remove the 2 Lower Rear Covers.
(6) Slide out the Paper Tray from the 3rd Paper
(5) Feed Module.
(7) (8)
(7)
Joint F Plate Joint C Plate
(11)
(13)
635
(14) Remove 2 Screws (Silver).
(14) Note:
The number of screws may vary on units
produced prior to Dec. 2000.
(16) (15) Remove the Lower Rear Cover.
(16) Slide out the Paper Tray.
(15)
(17)
(17) (18)
(18) (17)
(22) (22)
(23)
636
9.16. Installing the 2nd/4th Paper Feed Module and the Stand for 4-Paper Tray
Configuration (DA-DS205, DA-DA230-PA)
9.16.1. Contents
<DA-DS205> 2nd/4th Paper Feed Module
Qty. Description Part No. Remarks
1 2nd/4th Paper Feed Module DZHP004885
1 Extension Harness DZFP001023
4 Bracket DZJA000723
1 Size Label DZNK002812
8 Screw XTB3+8J
1 Installation Guide DZSM000427 This document
9.16.2. Installation
Note:
1. Turn the Power Switch to the OFF (O) position and unplug the AC Power Cord before
beginning installation.
2. Skip to the step (11) when installing the 4th Paper Feed Module to the DP-3000.
(1)
(2)x4
(3)
637
(4) Slide out 2 Paper Trays.
(6)
(5) Install the 4 Brackets.
(6) Secure the 4 Brackets with 8 Screws.
(5)
(4) (6)
(6) (5)
FRONT (11)
FRONT
(a)
638
(14)x4 (14) Remove 4 Screws (Silver).
Note:
The number of screws may vary on units
(16) produced prior to Dec. 2000.
(15) Remove the 2 Lower Rear Covers.
(16) Slide out the Paper Tray from the 3rd Paper
Feed Module.
(15)
(17) (18)
(17)
Joint F Plate Joint C Plate
(21)
(23)
639
(24) Remove 2 Screws (Silver).
(24) Note:
The number of screws may vary on units
produced prior to Dec. 2000.
(26) (25) Remove the Lower Rear Cover.
(26) Slide out the Paper Tray.
(25)
(27)
(27) (28)
(28) (27)
(33) (33)
(34)
640
9.17. Installing the Plain Stand (DA-D250) : For USA only
9.17.1. Contents
9.17.2. Installation
(1) Place the machine on top of the Plain Stand.
(1)
(2)
641
(4) Open the Plain Stand’s Front Cover.
(7) Joint Bracket E
(5) Open the Paper Tray No. 2.
(6) (6) Connect the machine to the Plain Stand with 4
Joint Bracket B Joint Brackets included in the hardware bag.
(7) (7) Secure each Joint Bracket with the 4 Screws
included in the hardware bag.
(6)
(8) Close the Paper Tray No. 2.
(9) Close the Plain Stand’s Front Cover.
(7)
(6) (10) Re-install the Rear Cover and secure it with the 2
Joint (7) Screws (Silver) removed in Step 2.
Bracket
D (5) Note:
The number of screws may vary on units
produced prior to Dec. 2000.
(4) (11) Place the machine in the desired location and
Joint Bracket A lower the leveler on each corner to stabilize the
machine.
(11)
642
9.18. Installing the Base Plate with Casters (DA-D200) : For USA only
9.18.1. Contents
FRONT
(1)
FRONT
643
(4) Remove 4 Screws (Silver) from the Rear Covers
(4) of the 3rd and 4th Paper Feed Module.
Note:
(6) The number of screws may vary on units
produced prior to Dec. 2000.
(5) Remove the Rear Covers.
(6) Open both Paper Trays.
(5)
(21)
(23)
644
(14) Remove 2 Screws (Silver) from the Rear Cover
(24) of the 2nd Paper Feed Module.
Note:
The number of screws may vary on units
produced prior to Dec. 2000.
(26)
(15) Remove the Rear Cover.
(16) Open the Paper Tray No. 2.
(25)
(27) (28)
(28) (27)
645
9.19. Installing the Plain Cabinet (DA-DE200) : For USA only
9.19.1. Contents
(4) Turn the Base Plate with the Plain Cabinet over
(Right side up).
(5) Place the 3rd Paper Feed Module (DA-DS210)
on top of the Plain Cabinet.
(5)
(8)
646
(10) (10) Connect the 3rd Paper Feed Module to the Plain
Joint Bracket E Cabinet with 4 Joint Brackets included in the
(11) Joint Bracket B Base Plate’s hardware bag.
(11) Secure each Joint Bracket with the 4 Screws
included in the Base Plate’s hardware bag.
(12) Close the Paper Tray.
(11) (11) (13) Close the Plain Cabinet’s Front Cover.
(10)
Joint
(11)
Bracket D Joint Bracket A (10)
(14)
(19) (18)
647
(21) Connect the 3rd Paper Feed Module Harness to
CN772 on the CST2 PC Board of the 2nd Paper
Feed Module.
(22) Place the Harness into the Wire Clamp.
(22) (23) Re-install the Rear Covers of the 2nd and 3rd
Paper Feed Module and secure the covers with
the 4 Screws (Silver) removed in Steps 6 and 15.
Note:
The number of screws may vary on units
produced prior to Dec. 2000.
(21)
(24)
(25)
648
9.19.3. Installation for DP-2000 configured with 1 Paper Tray only
(1) Place the Plain Cabinet with the flat surface
(3) (Top) facing downward over a clean cloth on the
(2) floor.
(2) Place the Plain Stand (DA-D250) with the
casters facing upwards on the Plain Cabinet and
open both Front Covers that are interlocked
together.
(3) Secure the Plain Stand to the Plain Cabinet with
4 Screws (Large) included in the Plain Cabinet’s
(1) hardware bag.
(3)
(4) Turn the Plain Stand with the Plain Cabinet over
(Right side up).
(5) Place the machine on top of the Cabinet Stand.
(5)
(6)
649
9.20. Installing the Dual-Path Exit Guide Unit (DA-FK200)
9.20.1. Contents
9.20.2. Installation
Note:
Turn the Power Switch to the OFF (O) position and unplug the AC Power Cord before
beginning installation.
(2)
(4)
650
(6) Disconnect the 3 Harnesses and pull them
(9) forward as illustrated on the left.
(7) Remove 5 Screws (Silver).
(8) Remove 1 Shoulder Screw (Silver).
(7) (9) Remove the Right Rear Cover, the Left Rear
Cover and the Lower Rear Cover.
(7)
(7)
(6)
(9) (8)
(11)
(10)
(13)
(12)
x7
(14)
(15)
651
(16) Remove the Rear Arm (A), Front Arm (B) and
(B)
2. then remove the Right Cover.
(A)
Note:
Please remove the Right Cover completely to
prevent damage that could cause duplex
skewing and jamming.
(16)
652
Notes for installing the Dual-Path Exit Guide Unit
1.
2.
1. Temporarily install the Dual-Path Exit Guide Unit
on top of the Fuser Unit.
2. Push down the Solenoid Arm slightly using a
3. minus screwdriver as illustrated on the left.
3. Make sure that the round-head part of the Turn
Guide is projecting from the square hole on the
White Solenoid Stay.
4.
1 2 3
5. The procedure for installing the Dual-Path Exit
Guide Unit looking from the side is illustrated on
the left.
653
(21) Remove 1 Screw.
(22) (22) Disconnect the harness of the Fan Assembly
(21) and remove the Fan Assembly.
654
9.21. Installing the Paper Transport Unit (DA-FK210)
9.21.1. Contents
9.21.2. Installation
Note:
Turn the Power Switch to the OFF (O) position and unplug the AC Power Cord before
beginning installation.
(3) (1)
(2)
(1)
(8)
(7)
x7
655
(9) Open the Right Cover.
(10) Install the Paper Transport Unit.
Note:
(10) When installing the Paper Transport Unit, put
the Harness of the Paper Transport Unit
through the opening of the Exit Cover. (Refer
to the step (6)).
(11)
(12)
(12)
656
(15) Remove 1 Screw.
(16) (16) Disconnect the harness of the Fan Assembly
(15) and remove the Fan Assembly.
657
9.22. Installing the Automatic Duplex Unit (DA-MD200)
9.22.1. Contents
9.22.2. Installation
Note:
1. Make sure that the Paper Transport Unit (DA-FK210) and the Dual-Path Exit Guide Unit
(DA-FK200) have already been installed.
2. Turn the Power Switch to the OFF (O) position and unplug the AC Power Cord before
beginning installation.
(1)
(1)
(3)
(2)
(4)
(6)
(5)
x7
658
(7) Disconnect the Intermediate Connector (Gray) of
the Right Cover.
(8) Remove the Harness from the 4 clamps.
(7)
(8)
(9)
659
(16) Pass the Harness of the Guide 1 Assembly
through the opening at the right corner of the
(16) Dual-Path Exit Guide Unit, and place the
harness into the white clamp.
(17) Connect the Harness of the Guide 1 Assembly
as illustrated on the left.
(16) (18) Re-install the Fan Assembly.
(17)
(20)
(19)
660
(25) Connect the Harness of the Guide 2 Assembly to
the sensor of the Guide 3 Assembly.
(26) Route the Harness through the Hooks on the
Guide 3 Assembly.
(26)
(25)
(31)
661
(34) Insert the SDRM PC Board (16 MB) into the
Duplex Memory socket on the SC PC Board as
illustrated on the left.
Note:
Make sure to insert the SDRM PC Board with
20-30 20 - 30° angle against the memory socket.
(35) Proceed with the installation of other options.
If finished, close and secure the Rear Plate and
re-install the remaining Covers and other parts.
(34)
For DP-2000
662
For DP-2500/3000
663
9.23. Installing the Exit Tray [Inner] (DA-XN200)
9.23.1. Contents
9.23.2. Installation
Note:
1. Make sure that the Dual-Path Exit Guide Unit has been installed before installing the Inner
Tray.
2. Turn the Power Switch to the OFF (O) position and unplug the AC Power Cord before
beginning installation.
(1)
b.
(3)
664
<When the Dual-Path Exit Guide Unit and the
(1) Paper Transport Unit are installed>
(1) Cut off the Paper Holder at the joint into two
parts with a nipper as shown on the left.
Note:
a. Cut ends neatly.
b. Dispose of the bottom part of the Paper
Holder.
b.
(3)
665
9.24. Installing the Exit Tray [Outer] (DA-XT200)
9.24.1. Contents
9.24.2. Installation
Note:
1. Make sure that the Paper Transport Unit (DA-FK210) and the Dual-Path Exit Guide Unit
(DA-FK200) have already been installed.
2. Turn the Power Switch to the OFF (O) position and unplug the AC Power Cord before
beginning installation.
(2)
(4)
(4)
(5)
666
9.25. Installing the 1-Bin Finisher (DA-FS200/FS205, DA-FS200S)
9.25.1. Contents
Note:
Order the required Installation Kit for 1-Bin Finisher (DA-FS200S) separately.
Other Countries: 1-Bin Finisher (DA-FS200: For DP-2000/2500, DA-FS205: For DP-3000)
Qty. Description Part No. Remarks
1 1-Bin Finisher -
1 Latch Catcher DZJA000739
2 Kit Fixing Claw DZJE000807
1 IPC Interface Board DZAA001208
3 Spacer DZJH000078 Stand offs
2 Screw DZPA000028
2 Washer DZPK000018
2 Screw DZPA000029 4x6, Silver
1 Screw DZPA000032 4x20, Black
4 Screw DZPA000030 4x25, Black
1 Installation Guide (1-Bin Finisher) DZSM000280 This document
667
Installation Kit for 1-Bin Finisher (DA-FS200S)
Qty. Description Part No. Remarks
1 Finisher Harness DZFP000856
For countries using 100V
DZHP003763
Power Supply.
1 LVPS Option Assembly
For countries using 200V
DZHP003866
Power Supply.
For countries using 100V
DZFP000848
Power Supply.
1 LVPS-OP Harness
For countries using 200V
DZFP000945
Power Supply.
1 Finisher Protective Bracket DZMA002395
2 Finisher Bracket DZJB000160
1 Harness Clamp DZJK000006
1 Stablizer DZJA000776
1 Stablizer Bracket DZJA000777
2 Adjuster DZMM000022
2 Cap DZMD000029
3 Screw DZPD000006 4x10, Silver
4 Screw XTB3+8J 3x8, Gold
4 Screw DZPB000007 3x8, Silver
668
9.25.2. Installation
Note:
1. Make sure that the Paper Transport Unit (DA-FK210), the Dual-Path Exit Guide Unit
(DA-FK200), the 2nd/3rd/4th Paper Feed Module (DA-DS200/205/210/215), the stand for 1/
2/3/4-Paper Tray Configuration (DA-DA200/210/220/230) and the Electronic Sorting Board
(DA-ES200) have already been installed.
2. Electronic Sorting Board is for the DP-2000 only.
3. Turn the Power Switch to the OFF (O) position and unplug the AC Power Cord before
beginning installation.
(7)
(6)
(8) (5)
(7)
669
<Installing the Stablizer for the Stand for
4-Paper Tray Configuration>
(d)
(c)
(c) (a) (b)
(9)
(11) (10)
(13)
(12)
x7
(15)
(14)
670
(17) Remove 4 Screws.
(18) Remove the LVPS Plate.
(18)
(17)
(19)
(17)
(23)
(22)
(25)
(24)
671
(26) Re-install the HF Bracket.
(27) Secure the HF Bracket together with the Ground
Strap of the Finisher Harness with 2 Screws.
(26)
(27)
(28)
(29)
(30)
(33)
672
<For Countries Using 100V Power Supply>
(35) Connect the LVPS Option Harness to the HTC
PC Board.
(35)
(35)
(38)
(38) (37)
(40)
673
(41) Install 2 FIN Brackets.
(41) (42) Secure 2 FIN Brackets with 2 Screws. (3x8,
Gold)
(42)
(42)
(43)
(44)
(A)
674
(47) Place the removed pads on the floor as shown
(A) on the left.
Note:
Width (A) should be the same as width (A) of
the box in the step (46) above.
(47)
(48)
(50)
675
(52) Extend the mount rail outward.
(52)
(55) Move the rail back in about 3.9 inches (10 cm),
3.9 inches (55) (55) then secure it with a tape.
(10cm) Note:
You may use the tape that was initially used to
keep the parts together in the shipping box.
676
(56) Install 1 Washer on each of the 2 Screws.
(56)
(57)
(58)
(59)
677
(60) Install the FIN Protective Bracket.
Note:
Hitch the bottom hook of the FIN Protective
(60) Bracket first and then to the upper 2 hooks.
(61) Secure the FIN Protective Bracket with 2
Screws. (3x8, Silver)
(61)
9.25.3. Repacking
Before repacking the Finisher into its original carton, please follow the procedure below.
(2)
(2)
678
(5) Place the Rear Aligning Guide to its home
(5) position by setting the DIP Switch (SW1) as
(6)
ON
shown on the left.
(6) Press the Push Button Switch (SW2), the Rear
1 2 3 4 5 6 7 8 Aligning Guide moves to its home position and
halts.
679
9.26. Replacing the EP-ROM on the 1-Bin Finisher (DA-FS200-PUA)
The 1-Bin Finisher is configured for the DP-2000/2500 copiers. If you are installing this Finisher on
the DP-3000 copier, replace the EP-ROM (4F1-1315) with the enclosed EP-ROM (4F1-2027) to
accommodate the faster speed of the DP-3000.
(3)
(3)
680
9.27. Installing the Dehumidifier Heater Kit
9.27.1. Contents
681
(10) Connect 4 Harnesses to the RLB PC Board
(10)
Heater 3 Harness Assembly as illustrated on the left.
(Short) • CN171 : RLB-Power Harness
• CN175 : RLB-SC Harness
(10) • CN172 : Heater 3 Harness (Scanner)
Heater 2 • CN173 : Heater 2 Harness (LSU)
Harness
(Long)
(10)
RLB-SC (10)
Harness
RLB-Power Harness
(11)
(13)
(18)
682
(19) Remove 2 Screws. (Gold)
(19) Note:
Do not remove the Red Screws.
(20) Remove the CCD Cover.
(20)
(24)
(23)
683
(29) Move the Lamp Base Unit slowly toward the
right, holding the bracket near the center
(29)
(Marked by *** as shown on the left).
684
(36) Break off the protective tab on the Lower Rear
Cover.
(37) Paste the Power Label on the Lower Rear Cover.
(37)
(36)
(38)
685
9.28. Installing the Key Counter Cable Kit (DA-KH200)
9.28.1. Contents
Note:
The Key Counter is sold separately.
9.28.2. Installation
Note:
Turn the Power Switch to the OFF (O) position and unplug the AC Power Cord before
beginning installation.
(1)
(3)
(2)
(5)
(4)
x7
(6)
686
(9) Break off the protective tab on the Right Rear
Cover.
(9)
(10)
(12)
(15) (14)
687
9.29. Replacing the OPC Drum
688
(5) Press down on the Release Latch.
Front Cover
(6) Pull the Process Unit slowly and straight out until
it stops.
Caution:
Support the Process Unit while pulling it out in
case it was not secured with 2 screws during
installation.
689
(11) Remove the OPC Drum as shown on the left,
holding by the front end where the OPC Drum
Shaft Holder was installed.
(12) Clean the Bias Charge Roller with the soft dry
cloth that came with the new OPC Drum.
690
(15) Remove the Protective Film from the OPC Drum.
691
10 Finisher
10.1. Overview
10.1.1. Features
1. Compact and light weight
2. Sorting and stapling by shift-sort
Operations of generating sheet stacks, matching, offset stacking, and stapling are performed on a
Halfway-processing Tray.
3. Stack Tray loading
The Stack Tray is capable of holding a maximum of 1000 small-sized sheets, or 500 large-sized
sheets. It also holds 30 stapled stacks (a maximum of 30 sheets each).
10.1.2. Specifications
A. Specification
Item Description
Stack Tray, tray descending/ascending style (fixed
Stacking style
Halfway-processing Tray)
Loading method Face-down loading
Inch-series LDR, LGL, LTR, LT-R, INV, INV-R, FLS1, FLS2
Copy paper size
A, B series A3, A4, A4-R, A5, A5-R, B4, B5, B5-R
Copy paper weight 50 g/m2 - 158 g/m2
Number of bins 1 bin
Staple mode
Modes Non-staple mode
Non-staple shift-sort mode
Small-size 1000 sheets
Non-staple Middle-size 700 sheets
Large-size 500 sheets
Small-size 30-sheet stacks
Stack Tray 80 g/m2
capacity *1 (maximum 30 stacks)
equivalent
Middle-size 20-sheet stacks
Staple sort
*2 (maximum 30 stacks)
Large-size 15-sheet stacks
*3 (maximum 30 stacks)
Aligning width Non-staple 8.3 x 11.7 in (210 - 297 mm)
*4 Staple 8.3 x 11.7 in (210 - 297 mm)
Aligning sheet Inch-series LDR, LGL, LTR, LT-R, INV, INV-R, FLS1, FLS2
size A, B series A3, A4, A4-R, A5, A5-R, B4, B5, B5-R
Stapling sheet Inch-series LDR, LGL, LTR, LT-R, FLS1, FLS2
size A, B series A3, A4, A4-R, A5, A5-R, B4, B5, B5-R
Offset stack allowed width
8.3 x 11.7 in (210 - 297 mm)
*6
Offset width
0.79 in (20 mm)
*5
Stapling method Hammering by rotary cam
Stapling position Rear diagonal stapling (one-point)
Small-size Maximum of 30 sheets
Stapling number of sheets Middle-size Maximum of 20 sheets
Large-size Maximum of 15 sheets
692
Item Description
Staple loading Special-purpose Cartridge (containing 3000 staples)
Staples Special staples
Staple sensor Provided
Manual staples Not provided
Sheet Sensor Provided
Controller Not provided (controlled from Main Unit)
Display Not provided (operation displayed on Main Unit)
Dimensions (W x D x H) 17.4 in x 22.6 in x 16.1 in (442 mm x 575 mm x 408 mm)
Weight Main unit: Approx. 26.5 lb (12kg),
Mounting kit: Approx. 6.6 lb (3 kg)
Power supply 24 VDC (supplied by Main Unit)
Maximum power consumption 40 W or less
45
5 2.5 mm
5 2.5 mm
693
- Section View
Stack Tray 1 (2111) End Plate B (2209) Feed Roller A (2327)
End Plate C (2215) Feed Roller B (2328)
Upper Guide (2317)
End Plate A (2208)
Return Roller
(2321)
Front Adjustment Plate Lower Guide
(2619) (2204)
Rear Adjustment Plate
(2623)
Adjustment Base
Loading Support
Retaining Lever (2702) Plate
- Top View
Rear Adjustment Plate (2623)
Paper Feed Belt (2611)
Hnadle (2115)
694
10.1.3. Operation
A. Removing a Paper Jam
Take the following steps a Paper Jam at the Finisher appears:
1. Hold the Handle and pull the Finisher away from the Main Unit.
Note:
When removing jammed paper, do not remove sheets on the Halfway-processing Tray.
1. Hold the Handle and pull the finisher away from the Main Unit.
695
2. Hold the Staple Cartridge at both sides (green portions) and pull out the Cartridge.
3. Hold the empty Staple Container at both sides and remove the Container.
Note:
Only one Staple Container can be mounted at one time. Use only the Staple Cartridge provided
specially for this model.
696
7. Push the Finisher toward the Main Unit.
2. Hold the Handle and pull the Finisher away from the Main Unit.
3. Hold the Staple Cartridge at both sides (green portions) and pull out the Cartridge.
697
4. Hold down the Staple Cartridge knob.
6. Return the Staple Cartridge knob to the home position and insert the Staple Cartridge into the Staple
Unit.
698
10.2. Operations
1. This section describes purposes and roles of each function, relation between the electronic system and
the mechanical system, and operation timings of each component. The outlines are described for
each function.
In the simplified diagrams, a " " symbol indicates transmission of mechanical movement and
" " symbol with a signal name indicate flow of electric signal.
2. High voltage levels are indicated as "1", and low voltage levels are indicated as "0" in description of
digital circuits for this unit. Voltage values differ depending on circuits. Descriptions of the circuits are
ones for the two sections, from sensors to main board input and from main board output to the load
and ones for block diagrams for each function.
10.2.1. Basic Configuration
A. Overview
This unit is composed of four blocks, Paper Ejection Section, Halfway-processing Section, Stapler
Section, and Stack Tray Section. Simplified diagram of the functions are provided below:
Paper Ejection
Section
Stack Tray Section
Halfway-
processing
Tray Section
Stapler
Section
Finisher Controller
PC Board
699
B. Electrical Circuits Overview
The operation sequences of the Finisher are controlled by the Finisher Controller PC Board. The
Finisher controller, which uses a 16-bit CPU, controls the sequences (mainly serial communication with
the Main Unit).
The Finisher Controller CP Board drives the motor in response to the commands sent from the Main Unit
via serial communication line. The Finisher Controller PC Board also sends information about sensors
and switches to the Main Unit via serial communication.
The ICs installed on the Finisher Controller CP Board has the following main functions:
- IC1 (CPU)
Sequence control
- IC3 (EP-ROM)
Contains sequence programs
- IC4 (communication IC)
Communication with Main Unit
- IC12 (regulator IC)
Generates 5-volt signals driving sensor and logic systems
IC3
EP-ROM
IC4
Communi-
cation IC
IC12
Regulator IC
700
C. Input/Output of the Finisher Controller PC Board
• Input/Output of the Finisher Controller PC Board (1/2)
Finisher Controller PC Board
Paper Ejection
Motor Clock
Sensor Pulse according to Rotation
Speed of Paper Ejection Motor
1
B10 B10
2
B11 B11
Entrance Sensor 3
B12
"1" when a Sheet is Running
B12
on the Sensor.
(shutter is at S2)
Return Roller
Home Position
Sensor "1" when Return Roller is on
Home Position Sensor.
(shutter is at S3)
A4 A4
Joint Sensor A5 A5
A6 "0" when Finisher is
A6 Connected to Main Unit.
(shutter is not at S4)
Halfway-
Processing Tray
Sheet Sensor "1" when a Sheet is Running
on the Sensor.
(shutter is at S5)
Front Aligning
Guide Home
Position Sensor "1" when front Aligning Guide
is at Home Position.
(shutter is at S6)
Rear aligning
Guide Home
Position Sensor "1" when Rear Aligning Guide
is at Home Position.
(shutter is at S7)
Paper Stack
Ejection Lever
Home Position
"0" when paper Stack Ejection
Sensor
Lever is at Home Position.
(shutter is not at S8)
Stack Tray B4 B4
Ascending/ B5 B5
Pulse according to Rotation
Descending B6
Speed of Stack Tray Ascending/
Clock Sensor B6
Descending Motor.
701
• Input/Output of the Finisher Controller PC Board (2/2)
Finisher Controller PC Board
B7 B7
Stack Tray Sheet B8 B8
Height Sensor B9 "1" when detecting
B9 sheet front.
(Shutter is at S10)
Stapler Cartridge
Sensor J402
"1" when Stapler Cartridge
is not mounted
Stapler No- "1" when no Stapler exists.
Staples Sensor (Shutter is not at S15)
"0" when no Stapler is at
hammering home position.
(Shutter is at S17)
Stapler Hammer
Home Position
Sensor
"1" when Stapler is not at
hammering position.
Stapler Head
Positioning
Sensor
Stapler Unit
702
• Output of the Finisher Controller PC Board
Finisher Controller PC Board
Controls rotation speed and
rotation timing by changing
Paper Ejection orders and frequencies of
Motor driving pulses (A, A*, B, and B*)
703
10.2.2. Basic Operation
Basic operation of the unit is illustrated below:
3. The sheet is fed by Return Roller Until it touches the Stopper Plate.
704
4. The sheet is aligned at a specified position by the Front/Rear Adjustment Plate.
5. Steps 1 through 4 are repeated for a specified amount of sheets until a specified amount of sheets are
loaded in the Halfway-processing Tray.
7. Paper stack loaded in Halfway-processing Tray is ejected onto the Stack Tray.
705
10.2.3. Sheet Carrier System
A. Overview
The sheets fed from the Main Unit are ejected onto the Halfway-processing Tray. The sheets are aligned,
offset, and stapled, and then ejected to the Stack Tray.
Paper Jam in the unit is detected by Entrance Sensor (S2).
The figure below shows configuration of the sheet carrier system:
Symbol Name
M1 Finisher 2 Motor (2417)
M2 Finisher 1 Motor (2402)
S1 Finisher 2 Motor Clock Sensor
S2 Entrance Sensor
S5 Halfway-processing Tray Sheet Sensor
J10-3
End Plate A (2208) S1D
End Plate B, C S1
J11-B12
S2D
J5
M2
Adjustment Base
loading support
plate 23T Gear
Paper Feed lever (2329)
J9-9
S5D
B. Paper Ejection
The sheets ejected from the Main Unit are carried to the Halfway-processing Tray by the Finisher Motor
2 (M1). Sheet transportation is detected by the Entrance Sensor (S2).
Paper ejection of the unit is provided with End Plates A and B. The End Plates A and B push down the
rear end of a sheet with its own weight, guiding the ejected paper through the Return Roller.
End Plate A (2208)
Pinch Roller
(2202)
S2
706
10.2.4. Halfway-processing Tray Section
A. Operation of Halfway-processing Tray
1. Overview
The Halfway-processing Tray is used to make up a paper stack for aligning, offsetting, and stapling the
sheets ejected from the Main Unit.
The Halfway-processing Tray includes Return Rollers and Stack Processing Belts. The two Stack
Processing Belts, provided with stack ejection levers, drive in parallel.
The Halfway-processing Tray Sheet Sensor (S5) is turned on when the Halfway-processing Tray is
loaded with sheets.
707
2. Finisher Motor 1 (M2) Control
The Finisher Motor 1 is a 4-phase Stepping Motor.
Switching of normal/reversed rotation of the motor, and motor rotation speed is controlled with the
phase of pulse signals, PUNDPINA, BUNDPINA*, BUNDPINB, and BUNDPINB*. IC6 outputs pulse
signals A, A*, B, and B* according to the change among PUNDPINA, BUNDPINA*, BUNDPINB, and
BUNDPINB*, controlling normal/reversed rotation, and rotation speed of the motor.
Motor torque is controlled with a combination of current control signals BUNDCUR1 and BUNDCUR2,
which are input to IC6.
This unit drives the motor in high torque, by normal rotation, when driving the Paper Feed Belts. The
motor is driven in low torque, within reversed rotation, when driving the Return Roller.
Stack processing
A J5-1 motor
BUNDPINA -5
M2
BUNDPINB A* -3
BUNDPINA* IC6
IC1
BUNDPINB* motor B
CPU
BUNDCURA driver
B*
BUNDCURB -2
-6
-4
708
B. Return Roller
1. Overview
The Return Rollers push the sheets fed from the Main Unit against the Stopper Plate, aligning the
sheets in carrying direction.
The Return Rollers drive in normal rotation when the Finisher Motor 1 drives in reversed rotation.
Return Roller
Stopper Plate
2. Operation Overview
Operation of the Return Roller is described below:
a. A Sheet is Ejected from the Main Unit.
b. The Return Rollers rotate in normal direction, pushing a sheet reaching the Halfway-processing
Tray against the Stopper Plate.
Stopper Plate
709
c. The rollers rotate for one turn and stop at home position.
d. Upon ejection of the next sheet, the unit repeats operations in steps 1 through 2, generating a sheet
stack. When the last paper of each stack is pushed against the Stopper Plate, the Return Rollers
pass through the home position and stop after rotating 1/8 turn.
e. After completion of aligning the sheets of the first stack, the Paper Feed Lever ejects the stack. At
the same time, the Return Rollers rotate in reverse direction. The Return Rollers, out of its home
position, do not interfere with the Paper Stack.
710
f. The Stack Processing Belt reaches its home position, finishing stack ejection. At the same time, the
Return Rollers stop at home position.
Home Position
g. From then on, steps 1 through 6 are repeated upon feeding of sheets for making the next stacks.
3. Timing Chart
First Paper Ejection Signal Second Paper Ejection Signal
711
C. Driving Paper Feed Belts
1. Overview
The Paper Feed Belts are driven when the Finisher Motor 1 (M2) rotates in normal direction. The two
belts operate in parallel at the same time. The Paper Feed Belts are provided with two Paper Feed
Levers, which are placed in back-to-back positions.
The Finisher Motor 1 (M2) is driven upon turning on the power of the Main Unit, places the Paper Feed
Levers at their home positions.
One operation of paper stack ejection is completed by a half turn of the belts.
Paper Stack
Paper Feed
Belt
23T Gear
Adjustment Base Loading
Support Plate
Paper Feed Lever
2. Operation Overview
Operation of the Paper Feed Belts is described below:
a. Upon turning on the copy start key of the Main Unit, the sheets are loaded onto the Halfway-
processing Tray. The Return Roller push the sheet against the Stopper Plate, aligning the sheets.
A specified number of sheets are loaded onto the Halfway-processing Tray.
712
b. Paper stack is carried toward the Stack Tray by the Paper Feed Lever, which is driven by the Paper
Feed Belts.
c. Paper feed belts are slowed down immediately before the paper stack is ejected onto the Stack
Tray. Irregularity in the paper stack is avoided by the slowing-down operation.
d. The belts stop temporarily, after ejecting the paper stack onto the Stack Tray.
713
e. After the Stack Tray descends, the Paper Feed Belts and the Return Rollers move to their home
position simultaneously, waiting for the next sheet of paper.
714
3. Timing Chart
• No stapling
First Paper Ejection Signal Second Paper Ejection Signal
715
• With stapling
First Paper Ejection Signal Second Paper Ejection Signal
716
D. Aligning/Offsetting
1. Overview
The sheets are aligned by the sides, in the Halfway-processing Tray, using Front/Rear Adjustment
Plates.
The front aligning motor (M3) drives the Front Adjustment Plate, and the rear aligning motor (M4)
drives the Rear Adjustment Plate.The Front Adjustment Plate Home Position Sensor (S6) and the Rear
Adjustment Plate Home Position Sensor (S7) detect the home positions of the Adjustment Plates.
The aligning positions and aligning sizes are summarized below:
717
2. Control of the Aligning Motor
The motors are both 4-phase stepping motors.
For controlling the motors, the signals shown below are output from IC1 (CPU).
718
Finisher Controller PC Board
+24V
Front Aligning
IC1 J6 Motor
(CPU) IC14 1
5 M3
IC7
3
5V
5V 2
6
4
+24V
Rear Aligning
J6 Motor
IC14 7
11 M4
5V IC8 8
5V 12
10
719
3. Rear Aligning (for Stapled Sorting)
Since the Stapler on the unit is mounted at the rear end, the sheets are aligned at the rear for stapling.
After turning on the copy start key, with sheet size data sent from the Main Unit, the Rear Adjustment
Plate moves to its home position, and the Front Adjustment Plate moves to a position which is away
from the center of the Stack Tray for a distance of half of a sheet width, plus 10 mm forward and then
standby.
A sheet ejected from the Main Unit is carried to the Halfway-processing Tray.
A sheet, after loaded into the Halfway-processing Tray, is pushed against the Stopper Plate by the
Return Rollers, and aligned in the transportation direction. The operation moves the sheet to the
stapling position. Afterwards, the Front Adjustment Plate is driven and the sheet is aligned at the rear
end.
Home Position of
Rear Adjustment Plate
Home Position of
Front Adjustment Plate
Home Position of
Rear Adjustment Plate
LDR/A3,
LTR/A4
Home Position of
Front Adjustment Plate
720
4. Offset Aligning (Non-stapling)
• Sorting
Upon sorting, the sheet stacks are aligned by dislocating the stacks in the Halfway-processing Tray.
The operation is called "offset aligning."
Offsetting amount for the sheet stacks is 0.79 in (20 mm).
Offsetting direction (forward/backward) for a first copy is opposite to that of a previous job. If the last
portion of a previous job was offset in forward direction, the first copy of a current job is offset in
backward direction. If the last portion of a previous job was offset in backward direction, the first copy
of a current job is offset in forward direction.
The Finisher Controller PC Board, upon receiving sheet size data sent from the Main Unit, moves the
front and Rear Adjustment Plates simultaneously to move the sheet to a position of sheet width +
10mm when placed at the center of the Stack Tray.
When aligning a sheet, only the front or Rear Adjustment Plate is moved for aligning. The Rear
Adjustment Plate moves to an end of a sheet to be offset for aligning at the front, or the Front
Adjustment Plate moves to an end of a sheet to be offset for aligning at the rear.
For sheet sizes of LTR/A4 and LDR/A3, however, the home position of the Front Adjustment Plate is
an offset reference position for aligning at the front, and the home position of the Rear Adjustment
Plate is an offset reference position for aligning at the rear. In that case, the Adjustment Plates (Rear
Adjustment Plate when aligning at front, or Front Adjustment Plate when aligning at the rear) also
stands by at the home position.
For aligning, the Adjustment Plates are moved from their home positions to the ends of the sheets to
be offset.
If a specified number of the sheets or the number of manuscripts exceeds the loading capacity of the
Halfway-processing Tray, the sheets beyond the maximum capacity are ejected once. Then, aligning
of the succeeding sheets is continued in the same direction.
Home Position of
Rear Adjustment Plate
Offset
amount
0.79 in
(20 mm)
Home Position of
Front Adjustment Plate
721
0.79 in
(20 mm) Home Position of
Rear Adjustment Plate
LDR/A3,
LTR/A4
Home Position of
Front Adjustment Plate
• Non-sorting
In a non-sorting operation, the sheets are aligned at an offset position at the front, the end where
sheets are aligned in the case of a operation with sorting.
Home Position of
Rear Adjustment Plate
Home Position of
Front Adjustment Plate
722
0.79 in
(20 mm)
Home Position of
Rear Adjustment Plate
LDR/A3,
LTR/A4
Home Position of
Front Adjustment Plate
5. Operation Overview
• Stapled sorting
Operation of stapled sorting is described below:
a. Turn on the copy start key on the Main Unit.
Data including the existence of stapling and sheet size, etc. is sent from the Main Unit.
b. The Front Adjustment Plate moves from its home position to the position away from the center of
the Stack Tray, by half the width of the sheet size +0.39 in (+ 10 mm).
Home Position of
Rear Adjustment Plate
(+10 mm)
Home Position of
Front Adjustment Plate
723
c. Load the Halfway-processing Tray with paper.
f. Repeat steps 3 through 5 for each sheet ejected from the Main Unit.
g. Upon completion of aligning the first stack, stapling starts.
724
h. Drive the Stack Processing Belts and eject the paper stack onto the Stack Tray.
i. Move up/down the Stack Tray to place the Stack Tray at a specified level.
j. From then on, repeat steps 3 through 8.
Note:
If the number of sheets exceeds the capacity of the Halfway-processing Tray, the paper stack on
the Halfway-processing Tray is ejected onto the Stack Tray without being stapled. The remaining
sheets are not stapled either.
• Offset aligning
Operation of offset aligning is described below:
In non-sorting operation, the sheets are offset-aligned only toward the front end.
a. Turn on the copy start key on the Main Unit.
Data including the existence of sorting and sheet size, etc. is sent from the Main Unit.
b. The Front/Rear Adjustment Plates move from its home position to the position away from the
center of Stack Tray by half the width of the sheet size 0.39 in (+ 10 mm) for both sides.
Home Position of
Rear Adjustment Plate
Half of sheet
width
+ 0.39 in 0.39 in (10 mm)
(10 mm)
Home Position of
Front Adjustment Plate
725
c. Load the Halfway-processing Tray with paper.
d. Move the Rear Adjustment Plate for aligning at the front, or move the Front Adjustment Plate for
aligning at the rear.
e. Front or Rear Adjustment Plate returns to the position in step 2 above.
726
f. Repeat steps 3 through 5 for each sheet ejected from the Main Unit.
g. Eject Paper Stack:
(a) When the number of sheets is within the capacity of the Halfway-processing Tray:
The sheets are ejected to the Stack Tray upon completion of processing each stack of copies.
(b) When the number of sheets exceeds the capacity of Halfway-processing Tray:
The paper stack in the Halfway-processing Tray is ejected to the Stack Tray.
The remaining sheets of paper are aligned at the same offset position and ejected to the
Stack Tray.
h. Move up/down the Stack Tray to place the Stack Tray at a specified level.
i. From then on, repeat steps 3 through 8 by changing the Adjustment Plates to move one after
another.
727
6. Timing Chart
a. Offset (2 originals - 2 copies)
1-1 Paper 1-2 Paper 2-1 Paper 2-2 Paper
Ejection Ejection Ejection Ejection
Signal Signal Signal Signal
*1 *1 *1 *1
728
b. Stapling (2 originals - 2 copies)
1-1 Paper 1-2 Paper 2-1 Paper 2-2 Paper
Ejection Ejection Ejection Ejection
Signal Signal Signal Signal
*1 *1 *1 *1
729
10.2.5. Stapling Operation
1. Overview
The Staple Unit of this model, which is fixed at the rear side, does not move or sway.
Stapling is performed at one position from underneath, before paper stack ejection. This unit does not
provide functions for manual stapling or manually-fed stapling.
Stapling Home
Position
Stapling Home
Position
Figure 2-501
Note:
If the specified number of sheets exceeds a maximum number of sheets to be stapled, the sheet
stack is ejected to the Stack Tray.
2. Return Rollers
The motors and sensors related to stapling are listed below:
SW: Micro Switch
PI: Photo Interrupter
730
3. Stapling Motor Control
Overview of the driving circuit for stapling motor (M6) is described below:
A DC motor is used for the Stapling Motor.
The rotating direction of the motor is switched over by a signal sent from the Finisher Controller PC
Board IC4 (communication IC) to the motor driving circuit.
24V
IC4 Stapling
(Commu- Q20 Q21 Motor
nication J8-1
-2
IC)
-4 M6
5V -5
Q24 Q25
5V
731
10.2.6. Stack Tray Operation
1. Moving Up/Down Stack Tray
A. Overview
This unit is provided with a one-level Stack Tray. The sheets aligned, offset, and stapled in the
Halfway-processing Tray are ejected to the tray.
Upon ejection of a first sheet to the Stack Tray, the Stack Tray Sheet Sensor (S11) is turned on.
The Stack Tray is moved up/down by the Stack Tray movement motor (M5). If the Stack Tray is not at
its home position when the power of the Main Unit is turned on, the tray is moved to its home position
by the Stack Tray movement motor. Here, a home position of the Stack Tray is set at a level 0.49 in
(12.5 mm) higher than a point where the Stack Tray Sheet Height Sensor detects the surface of the
Stack Tray. Position of the Stack Tray is detected by measuring the distance from the Stack Tray Sheet
Height Sensor (S10), using the number of clocks in the movement.
The upper limit of the Stack Tray position is detected by the Stack Tray Upper Limit Sensor (S13), and
its lower limit is detected by the Lower Limit Sensor. If the Stack Tray Upper/Lower Limit Sensor is
turned on, the Stack Tray movement motor is driven in a direction opposing to the detected sensor.
The loading limit of the Stack Tray, for unstapled sheets, is detected with the Sheet Height Sensor and
the Lower Limit Sensor. For unstapled sheets, the limit is detected by the copy counter. Upon
detecting the height limit or the number of copies, which is overloading, it is reported to the Main Unit.
732
B. Stack Tray Ascending / Descending Operation
The Stack Tray, after ejecting the Paper Stack, moves down until the Stack Tray Sheet Height Sensor
(S10) is turned off. Then, after the Sheet Height Sensor (S10) detects the upper surface of sheets on
the Stack Tray, the tray moves up by 0.49 in (12.5 mm).
Stack Tray
733
C. Timing Chart
The Stack Tray ascending/descending timing chart is shown below.
1-1 Paper 1-2 Paper 2-1 Paper 2-2 Paper
Ejection Ejection Ejection Ejection
Signal Signal Signal Signal
*1 *1 *1 *1
734
2. Detecting Stack Tray Sheet Height.
In all operation modes, paper loading on the Stack Tray is detected with the height of sheets loaded on
the Stack Tray. The height of the sheets is the Stack Tray Sheet Height Sensor (S10).
The Stack Tray, after ejecting the sheets, moves down until the Stack Tray Sheet Height Sensor (S10)
does not detect the sheet and then stops.
Then, the Stack Tray Sheet Height Sensor (S10) detects the surface of a sheet on the Stack Tray, and
the Stack Tray moves up by 0.49 in (12.5 mm).
If the Stack Tray Lower Limit Sensor detects the Stack Tray while the Stack Tray Sheet Height Sensor
is detecting the surface of a sheet, the Finisher Controller PC Board reports overloading of the tray to
the Main Unit. After the sheets on the Stack Tray are removed, the Stack Tray moves up to its home
position. Then, ejection of the next sheets is enabled.
735
3. Counting the Number of Copies Loaded in the Stack Tray.
The loading capacity of the Stack Tray is summarized in the table below.
When stapling the sheets, the loading capacity of the Stack Tray is detected by counting the number of
copies loaded onto the Stack Tray in addition to detecting the height of the sheets. One copy of a
sheet stack is counted as "1." Upon counting a total of 30 copies, overloading on the Stack Tray is
reported to the Main Unit.
The controller on the Main Unit displays an instruction for removing the sheet stacks.
For continuing the copy operation after the above action, the unit displays instruction for removing
sheets on controller if sheets are loaded onto the Stack Tray. Starting copy operation here without
removing the sheets does not guarantee correct aligning of sheets or stapling performances.
Even if the sheets are not removed, counting of the sheet stacks is cleared upon turning on the copy
start key, and the number of copies is counted from the beginning.
Sheet-holding
Lever
736
(Tray moves down)
5. Tray Ascending/Descending Motor Control.
a. Overview
A block diagram of the drive circuit for the Tray Ascending/Descending Motor (M5).
A DC motor is used for Tray Ascending/Descending Motor.
Rotating direction of the motor is switched over by a signal sent from the Finisher Controller PC Board
IC1 (CPU) to the motor driving circuit.
When the Stack Tray reaches the Stack Tray Upper Limit Sensor (S13) and the sensor sends a signal
(S13D) to IC11, STKTCW breaks and the motor stops further rotation in normal direction. Similarly,
when the Stack Tray reaches the Stack Tray Lower Limit Sensor (S12) and the sensor sends a signal
(S12D) to IC11, STKTCCW breaks and the motor stops further rotation in reverse direction.
IC11
S13D
S12
Stack Tray
Lower Limit Sensor
S13
Stack Tray
Upper Limit Sensor
737
10.2.7. Detecting Jam
A. Overview
The unit is provided with the sensors listed below for detecting presence/absence of sheets, and normal
transportation of sheets:
• Entrance sensor
• Return Roller Home Position Sensor (S3)
• Paper Feed Lever Home Position Sensor (S8)
Also, for detecting the normal operation of stapling, the sensor below is provided:
• Stapling Home Position Sensor (S17)
Jamming is checked at timing memorized in CPU on the Finisher Controller PC Board. Upon detection
of jamming, paper ejection is stopped and jamming is indicated on the controller section.
738
B. Sheet Transportation Jam
Sheet Transportation Jam is described below:
739
3. Paper Stack Ejection Jam
Upon moving the Paper Feed Lever with the Finisher Motor 1 (M2), the jam is detected if the Paper
Feed Lever does not reach the Paper Feed Lever Home Position Sensor (S8), despite the lever moved
sufficiently. The jam is detected also if the Paper Feed Lever does not move away from the Paper
Feed Lever Home Position Sensor, despite the lever should have been moved sufficiently.
The jam is detected during transportation of the sheets. If the jam is detected upon the initialization
process, it is processed as an error.
• If the lever does not reach the home position
1-2 Sheet 2-1 Sheet 2-2 Sheet
Ejection Signal Ejection Signal Ejection Signal
*1 *1 *1 Detect Jam
Halfway-processing Tray
Sheet Sensor (S5)
0.3 0.3
Finisher Motor 1 (M2) *2 seconds *3 *2 seconds *3
Halfway-processing Tray
Sheet Sensor (S5)
0.3 0.3
Finisher Motor 1 (M2) *2 seconds *3 *2 seconds
740
4. Stack Returning Jam
Upon moving the Return Roller with the Finisher Motor 1 (M2), the jam is detected if the Return Roller
does not reach the Return Roller Home Position Sensor (S3) despite the lever should have been
moved sufficiently. The jam is detected also if the roller does not move away from the Return Roller
Home Position Sensor despite the lever should have been moved sufficiently.
The jam is detected during transportation of sheets. If the jam is detected upon initialization process, it
is processed as an error.
• If the roller does not reach home position
1st Sheet 2nd Sheet
Ejection Signal Ejection Signal Detect Jam
Halfway-processing Tray
Sheet Sensor (S5)
Finishe Motor 1 (M2) *1 *2 *1 *2
Halfway-processing Tray
Sheet Sensor (S5)
Finishe Motor 1 (M2) *1 *2 *1 *2
741
C. Stapler Jam
Stapler jam is described below:
742
10.2.8. Electrical Systems
1. Overview
Upon turning on the power of the Main Unit, a 24-VDC power is supplied from the Main Unit to the
Finisher Controller PC Board. The regulator IC (IC12) on the Finisher Controller PC Board generates
5-VDC power. The 5-VDC power is used for sensors and ICs on the board.
A block diagram of the power supply system is provided below:
Finisher Controller PC Board
Motors
24V
24V Circuit
M
Breaker
CB1
Regulator 5V
IC
(IC12)
Sensors
Logic
System
2. Protection Functions
For overcurrent protection, a circuit breaker (CB1) is provided on motor-driving 24-VDC power.
743
10.3. Maintenance
This chapter describes the mechanical features of the system, operations, and procedures for
disassembling/assembling the unit.
Keep the following points in mind when disassembling/assembling the unit:
1. Be sure to disconnect the power plug before disassembling/assembling the unit.
2. For assembling, reverse the disassembling procedures except as noted.
3. When assembling, be sure to use the correct Screws (length and diameter) in the correct positions.
4. For preventing static electricity, a chrysanthemum-shaped washer is used at one of the Screws for
mounting the metal cover. Be sure to use the washer when assembling.
5. Do not operate the unit with any part not mounted.
10.3.1. Maintenance and Inspection
A. Regular Maintenance Parts
The unit does not use any part that should be replaced regularly.
C. Regular Maintenance
Return roller (cleaning/for each 120 thousand operations).
744
10.3.2. Exterior Cover
(1) Pull out the Finisher Frame.
(6)
(2) 2 Screws (2016).
(3) Remove 2 Finisher Locking Mount Cap
(2) (3) (2006).
(4) 2 Screws (2016).
(5)
(4) (3) (5) Remove 2 Finisher Lower Mount Cover
(2005).
(6) Remove the Finisher Frame.
(2)
(5)
(4)
(9)
(9)
(11) x4
(13)
745
(17) (15) 1 Screw (2021).
(16) 4 Screws (2016).
(17) Remove the Right Panel (2104).
(15) (18) Remove the Rear Panel (2105).
(18)
(16) (14)
(16)
(19)
Note 1:
1. Insert tip of the Screw to the Screw hold and turn
the Screw counter-clockwise.
2. A click is felt when the thread of the Screw fits
Screw hole.
3. Turn the Screw clockwise.
Note 2:
Pay attention not to leave scratches or scores on
the rails of the loading wall (A). Scratches or
scores may affect the loading capacity.
(A)
746
Note 3:
Stack Tray Stopper Screw must be tightened
completely through the plate (do not leave it
loosened). A loose Screw may interfere with
sliding of the rail.
747
10.3.3. Transportation Motor
(1) Remove the Harness from 2 Clamps.
(1) (2) Disconnect the Sensor Connector.
(3) Disconnect the Motor Connector.
(2) (3)
(4)
(7)
(8)
(7)
748
10.3.4. Adjustment Base
(1) Remove the Right Plate, Left Plate and the
Staple Cover. (See 10.3.2.)
(2) Remove the Stapler. (See 10.3.8.)
(3) 1 Screw (2030).
(4) Remove the Sensor Holder (2220).
(2) (1)
(9)
(8)
(10)
749
(11) Disconnect the Connector J6 and J9 on the
Finisher Controller PC Board.
(13) (12) 2 Screws (2016).
(13) Remove the Adjustment Base (2639)
Assembly.
(12)
(12)
(11)
(14)
(14)
Note 1:
Stack Tray may interfere when removing Screw on
Finisher Frame. As shown in the figure on the left,
rotate the Clock Plate of Stack Tray Shift Motor
clockwise to move down the Stack Tray, allowing
the Screw to be removed.
Note 2:
(B) When mounting the Processing Tray, Verify that
the 3 Loading Wall Rails (A) fit into the Adjustment
Base Assembly (B) as shown in the figure on the
left.
(A)
750
(16) Disconnect the Motor Harnesses from 3
(18) (18)
(19) (16) Clamps.
(17) Disconnect 2 Motor Connectors.
(18) 4 Screws (2014).
(19) Remove 2 Finisher 4 Motors (2630).
(17)
(16)
(17)
(28)
(26)
751
(30) (29) Disconnect the Sensor Connector.
(30) Remove the Actuator Guide (2636).
(31) Remove the Sensor (2114).
(31)
(29)
(33)
(36)
(35)
(34)
752
(39) Disconnect the Sensor Connector.
(40) Remove the Sensor (2114).
(39)
(40)
(47) 1 Screw.
(48) 6 Screws (2035).
(48)
(49) Remove the Rear Drive Plate (2634) Assembly.
(49)
(47)
753
(50) 3 Screws.
(51)
(50) (51) Remove the Operating Tray Plate (2609)
Assembly.
(50)
(50)
(52)
(54)
754
10.3.5. Return Roller
(1) Remove the Adjustment Base (2639)
Assembly. (See 10.3.4.)
(2) Disconnect the Motor Connector.
(3) 2 Screws (2014).
(2) (4) Remove the Finisher 1 Motor (2402).
(3)
(4)
(5)
(6)
(7)
(9)
(8)
(10) (10)
755
(13) Rotate the Return Roller to a position where the
Return Roller does not touch the Lower Guide,
and then pull out the Return Roller Assembly.
(13)
(13)
756
10.3.6. Stack Tray Ascending/Descending Unit
(1) Remove the Right Plate, Left Plate and the
(4)
Staple Cover. (See 10.3.2.)
(2) Remove the Adjustment Base Assembly.
(See 10.3.4.)
(3) 1 Screw (2028).
(4) Remove the Sensor Unit.
(5) Remove the Return Roller (2321) Assembly.
(3)
(6) Remove the Finisher Controller PC Board
(2403).
(7) Release the Belt Bracket Plate (2301).
(8) Remove the Transportation Driver Unit.
(See 10.3.3.)
(9) Disconnect the Sensor Connector.
(10) Remove the Sensor (2114).
(10)
(9)
(13)
757
(15) 1 Screw (2030).
(16) Remove the Sensor Holder (2410).
(16)
(15)
(18)
(19) (19)
(21)
758
(23) 1 Screw (2020).
(25) (24) Remove the Ground Wire.
x6
(25) 6 Screws (2018).
(23)
(24)
(32) (32)
759
(33) Disconnect the Sensor Connector.
(34) Remove the Sensor (2114).
(34)
(33)
(36)
(35)
(37)
(38)
760
(39) Remove the E-Clip (2057).
(40) (40) 1 Screw (2038).
(39) (41) Remove the Bracket Plate (2718) Assembly.
(42) (42) Remove the Timing Belt (2715).
(41)
(46)
(43)
(49)
(48)
(47)
(51)
761
10.3.7. Finisher Controller PC Board
(1) Remove the Rear Plate. (See 10.3.2.)
(2)
(2) Disconnect all Connectors on the Finisher
Controller PC Board.
(2)
(2)
(2)
(6) (4) x3
(3)
762
10.3.8. Stapler
(1) Remove the Right Plate, Left Plate and the
(4) Staple Cover. (See 10.3.2.)
(2) Remove the Transportation Driver Unit.
(See 10.3.3.)
(3) Remove the Finisher Controller PC Board.
(See 10.3.7.)
(4) 2 Screws (2014).
(5) (5) Remove the Stapler.
(4)
763
10.3.9. Stack Tray Drive Unit
(1) Remove all Harnesses from 4 Clamps.
(2) Disconnect the Sensor Connector.
(3) Remove the Sensor (2114).
(1)
(2)
(1)
(3)
(6)
(5)
(8)
(7)
(7)
(9)
764
10.3.10. Static Prevention Needles
(1) Lift the Upper Guide (2317) to uppermost
position and hold down with tape.
(1)
(3)
765
10.3.11. Adjusting Aligning Width
Note:
Be sure to adjust the aligning width after steps of "Adjusting Aligning Plate Angle" or "Adjusting Overlap
Amount of Sensor Flag."
766
(11) Adjust position with reference to index, and
A B move Front Adjustment Plate Home Position
Sensor (S6).
Example 1)
If the width in step (2) is 12.6 in (319 mm), the
difference from standard value, 12.5 in (317 mm),
(11) is +0.08 in (2 mm). Therefore, move Sensor
toward arrow A in the figure on the left by 0.08 in
(2 mm).
Example 2)
Example 2) If the width in step (2) is 12.4 in (316
mm), the difference from standard value, 12.5 in
(317 mm), is -0.04 in (1 mm). Therefore, Move
Sensor toward arrow B in the figure on the left by
0.08 (1 mm).
Note:
Right Cover A marking (A) indicating standard 12.5 in (317
mm) width is provided on the back of Right Cover.
A large-size sheet folded at the marking may be
used as reference for measuring the width of
Adjustment Plate.
(A)
Large-size Sheet
767
10.3.12. Adjusting Angle of Adjustment Plate
(1) With the Adjustment Base Assembly mounted,
loosen 2 Screws (2034) on the Rear Adjustment
Plate.
(1)
Rear
Push against
Adjustment
Plate
Finisher Frame
768
10.3.13. Adjusting Overlap Amount of Sensor Flag
After replacement of mechanical parts, usually, the overlap amount is adjusted to the previous index shown
in step (11) in Adjusting Aligning Width“. However, if overlap amount between sensor and flag has changed
due to some reasons, the adjustment procedures described below are applicable:
(1)
0.06 0.08 in
(1.5 2 mm)
769
10.3.14. Adjusting Tension of Finisher 1 Motor Belt
(1) Remove the Right Plate and Rear Plate.
50mm (See 10.3.2.)
(2) Prepare a piece of paper of 0.39 in (10 mm)
width by 7.9 in (200 mm) length using 64/m2
paper, and fold it into four.
10mm
(3)
(4)
770
(6) Remove the paper.
(7) Verify that the Roller Shaft (2323) moves up and
down smoothly.
(6)
771
10.3.15. Releasing Stack Tray Guide Lever Holding Plate
(1) Remove the Right Plate, Left Plate and the
Staple Cover. (See 10.3.2.)
(2) Remove the Stack Tray. (See 10.3.2.)
(3) Rotate the Clock Plate (2501) so that Front
Tray Support Plate (2109) and Rear Tray
(4) (5) Support Plate (2110) are seen through the hole
on Side Plate. (Moves down by turning
clockwise, and moves up by turning counter-
clockwise.)
(4) 1 Screw (2030).
(5) Remove the Belt Bracket Plate (2301).
(Same procedures are applicable to both front
side and rear side.)
Note:
Hold down the Tray Support Plate when removing
the Screw.
772
10.3.16. Reinstalling Stack Tray Guide Holding Plate
(1) Remove the Transportation Driver Unit.
(See 10.3.3.)
(2) Loosen 1 Screw (2030) (Front/Rear), loosing the
tension of Timing Belt (2320).
(2)
(4)
Note:
Reinstall the Tray Support Plate (at front and rear)
where the bottom of the Belt Bracket Plate fits a
marking on the frame. This arrangement secures
Tray Support the position of Tray Support Plate (at front and
Plate
rear).
Marking
Tray Support
Plate
Marking
773
10.4. Troubleshooting
10.4.1. Function List for DIP Switches
This section summarizes the operation using the DIP switches (SW1) on the Finisher Controller PC Board.
- Operation procedures
1. Correct faults of operations on applicable systems.
2. Set up the DIP switch (SW1) and turn on the power. (LED1 blinks.)
3. Pressing the push switch (SW2) starts operations under the conditions listed below. (LED2 flashes
during operations.)
ON Finisher Motor 1 Paper Feed Lever moves to home • Turn off Joint Sensor
(Paper Feed position and stops. (S4)
Lever) • Open Finisher
1 2 3 4 5 6 7 8
ON Finisher Motor 1 Return Roller moves to home position • Turn off Joint Sensor
(Return Roller) and stops. (S4)
• Open Finisher
1 2 3 4 5 6 7 8
Front Aligning Not at home Front Adjustment • Turn off Joint Sensor
Motor position Plate moves to home (S4)
ON position and stops • Open Finisher
At home position Moves toward • Turn off Joint Sensor
pressing direction for (S4)
1 2 3 4 5 6 7 8 specified amount • Open Finisher
and stops at home
position
Rear Aligning Not at home Front Adjustment • Turn off Joint Sensor
Motor position Plate moves to home (S4)
ON position and stops • Open Finisher
At home position Moves toward • Turn off Joint Sensor
pressing direction for (S4)
1 2 3 4 5 6 7 8 specified amount • Open Finisher
and stops at home
position
ON Stack Tray Stack Tray moves up and stops upon • Press SW2 again
Motor detection by the Stack Tray Upper • Turn off Joint Sensor
{ascending} Limit Sensor (S4)
1 2 3 4 5 6 7 8 • Open Finisher
ON Stack Tray Stack Tray moves down and stops • Press SW2 again
Motor upon detection by Stack Tray Lower • Turn off Joint Sensor
(Descending) Limit Sensor (S4)
1 2 3 4 5 6 7 8 • Open Finisher
ON Stapling Motor Halts after stapling operation • Turn off Joint Sensor
(S4)
• Open Finisher
1 2 3 4 5 6 7 8
774
10.4.2. Electrical Parts Alignment Diagram
1. Electrical Parts Alignment Diagram
S13 M1
S4
S11 S15-18
S2 M6
S10 [1]
S1
M5
S3
M2 S9
S12
S7
M4
S5 S8
S6 M3
775
<1.Sensors>
Symbol Function
[1] Finisher Controller PC Board
776
2. LEDs and Connectors on the Finisher Controller PC Board
LEDs and Connectors required for service are shown below:
Notes:
a. Some of the LEDs may glow slightly after being turned off, due to a leak of current under normal
operation. Make sure no to misread these LEDs.
b. The Connectors not shown in this illustration are for factory use only. Do not touch these
Connectors in the field as special tools and high-precision measuring devices are required.
J8 J9
J6
J10
J5
J11
J4
LED1
J3
LED2
LED3
SW2 SW1
CB1
J2 J1 J12
777
10.4.3. Troubleshooting Faulty Operations
1. E5-22 (Communication Failure between the Main Unit and the Finisher)
778
4. E7-20 (Rear Aligning Motor (M4) Failure)
779
Cause/Faulty Section Step Check Result Action
Tray Alignment 3 Check whether the Front and Rear No Correct the Front and
(Height Adjustment) of the Stack Tray is Rear Stack Tray
correctly aligned. alignment.
Stack Tray Ascending/ 4 Check whether the Stack Tray No Replace the Change
Descending Motor Ascending/Descending Motor Clock Sensors
Clock Sensor (S9) Sensor (S9) is operating normally.
Stack Tray Sheet 5 Check whether the Stack Tray Sheet No Replace the Change
Height Sensor (S10) Height Sensor (S10) is operating Sensors
normally.
Stack Tray Upper Limit 6 Check whether the Stack Tray Upper No Replace the Change
Sensor (S13) and Stack Limit Sensor (S13) and Stack Tray Sensors
Tray Lower Limit Lower Limit Sensor (S12) are operating
Sensor (S12) normally.
Finisher Controller PC 7 Check whether the voltage between J3- No Replace the Finisher
Board 1 and 2 on the Finisher Controller PC Controller PC Board
Stack Tray Ascending/ Board goes to 24 VDC when the Stack Yes Check the connections
Descending Motor (M5) Tray Ascending/Descending Motor (M5) from the Stack Tray
driver is initialized. Ascending/Descending
Motor (M5) to the
Finisher Controller PC
Board. If connection is
good, replace the motor.
10.4.4. Self Diagnosis
A. Self Diagnosis
Code
Main Cause Detection Timing
Indication
E5-22 • Fault in the connection with the Main Unit Communication between the Main Unit and
(Loose Connector) Finisher failed to recover within 5 seconds.
• Fault in the Finisher Controller PC Board
or IPC PC Board and/or LPC PC Board in
the Main Unit.
E7-21 • Fault in Finisher Motor 2 (M1) The Finisher 2 motor clock sensor (S1)
• Fault in Finisher 2 motor clock sensor (S1) signal is not detected after the Finisher
• Fault in the Finisher Controller PC Board Motor 2 (M1) carries the paper for a specified
amount (70 mm in, for 80 pulses)
E7-28 • Fault in Finisher Motor 1 (M2) • The Paper Feed Lever does not reach the
• Fault in the Paper Feed Lever Home Home Position Sensor (S8) after driving
Position Sensor (S8). the Finisher Motor 2 (M2) for a specified
• Fault in the Return Roller Home Position amount of time.
Sensor (S3). • The Return Roller does not reach the
• Fault in the connection to the Finisher Home Position Sensor (S3) after driving
Motor 1 (M2). the Finisher Motor 1 (M2) for a specified
• Fault in the Paper Feed Belt amount of time.
• Fault in the Return Roller
E7-20 • Fault in the Rear Aligning Motor (M4) • The Rear Aligning Guide does not reach
• Fault in the Rear Aligning Home Position the Home Position Sensor (S7) after
Sensor (S7) driving the Rear Aligning Motor (M4) for a
• Fault in the connection to the Rear specified amount of time.
Aligning Motor • The Rear Aligning Guide does not leave
• Fault in the load on the Rear Aligning the Home Position Sensor (S7) after
Motor driving the Rear Aligning Motor (M4) for a
specified amount of time.
780
Code
Main Cause Detection Timing
Indication
E7-23 • Fault in Stapler Motor (M6) • The Stapler does not leave the Stapling
• Fault in the Stapling Home Position Home Position Sensor (S17) within 0.5
Sensor (S17) seconds after the Stapler motor is driven in
• Fault in Stapler connection the normal rotation.
• Fault in the Finisher Controller PC Board • The Reversed rotation of the Stapler motor
does not return to the Stapling Home
Position Sensor (S17) within 0.5 seconds
either.
E7-22 • Fault in the Front Aligning Motor (M3) • The Rear Aligning Guide does not reach
• Fault in Front Aligning Home Position the Home Position Sensor (S6) after
Sensor (S6) driving the Rear Aligning Guide Motor
• Fault in the connection with the Rear (M3) for a specified amount of time.
Aligning Motor • The Rear Aligning Guide does not leave
• Fault in the load on the Rear Aligning the Home Position Sensor (S6) after
Motor driving the Rear Aligning Guide Motor
(M3) for a specified amount of time.
E7-27 • Fault in the Stack Tray Ascending/ • The Stack Tray Upper Limit Sensor (S13)
Descending Motor (M5) is activated during operation of the Stack
• Fault in the Stack Tray Sheet Height Tray Ascending/Descending Motor (M5).
Sensor (S10) • The detection of the clock signal for the
• Fault in the Stack Tray Ascending/ Stack Tray Ascending/Descending Motor
Descending Motor Clock Sensor (S9) Clock Sensor (S9) fails within 15 times or
• Fault in the load on the Stack Ascending/ more within 0.8 seconds during the
Descending Motor operation of the Stack Tray.
• Fault in Finisher Controller PC Board • The Stack Tray does not reach the Stack
Tray Sheet Height Sensor (S10) even after
the Ascending/Descending Motor (M5)
starts
• The Stack Tray does not leave the Stack
Tray Sheet Height Sensor (S10) even after
the Ascending/Descending Motor (M5)
starts.
781