Академический Документы
Профессиональный Документы
Культура Документы
CTION MANUAL
FOR BH-800Ⅲ TRIPLEX MUD PUMP
JUNE 2007
INSTRUCTION MANUAL FOR BH-800III MUDP
Foreword
2
INSTRUCTION MANUAL FOR BH-800III MUDP
Content
1. General.................................................................................................................................4
2. Technical parameters......................................................................................................4
3. Structural features ..............................................................................................................6
3.1 Power end (see Figure 2)...........................................................................................6
3.2 Fluid end (see Figure 6) .........................................................................................8
3.3 Lubrication system of power end (see Figure 8)................................................13
3.4 Lubrication system of fluid end (see Figure 9) .....................................................15
4. Installation of new pump..................................................................................................17
5. Pump application ..............................................................................................................18
6. Pump maintenance............................................................................................................19
6.1 Maintenance of power end .....................................................................................19
6.2 Fluid end maintenance............................................................................................28
7. Periodic maintenance regulations....................................................................................30
8. Troubleshooting.................................................................................................................33
9. Expendables list.................................................................................................................35
10. Special tool list...........................................................................................................36
3
INSTRUCTION MANUAL FOR BH-800III MUDP
1. General
BH-800III triplex single acting mud pump is the new model one developed by
our company. It takes the advantages of high efficiency, light weight and novelty
construction, being ideal equipment for drilling, workover and completion
operations.
2. Technical parameters
Type: Triplex single acting piston pump
Max. horsepower: 800HP (588kW)
Rated strokes: 175r/min
Stroke length: 8 1/2¡±(216mm)
Max. working pressure: 5000psi(35MPa )
Gear ratio: 4:1
Valve pot size: API 7#
Inlet diameter: 8¡±(203mm)
Outlet diameter: 4¡±(102mm)
Weight: 22000Lbs (10000kg)
Overall dimensions: L145.5¡±W98.5¡±H88.5¡±
(3700x2500 x2250mm)
Performance data:
Power Liner Dia & Pressure Mpa (PSI)
Strokes/m 7¡± 6 ½¡± 6¡± 5 ½¡± 5¡± 4 ½¡± 4¡±
in 12.4 14.4 16.9 20.1 24.3 30.0 35
kW HP
1771 2057 2414 2871 3471 4286 5000
Displacement (L/S)
175 648 880 46.90 40.43 34.48 29.05 23.98 19.43 15.49
160※ 592 805 42.88 36.96 31.52 26.56 21.92 17.76 14.16
150 555 755 40.20 34.65 29.55 24.90 20.55 16.65 13.28
140 518 705 37.52 32.34 27.58 23.24 19.18 15.54 12.39
130 481 654 38.84 30.03 25.61 21.58 17.81 14.43 11.44
120 444 604 32.16 27.72 23.64 19.92 16.44 13.32 10.56
110 407 554 29.48 25.42 21.67 18.26 15.07 12.21 9.68
1 0.268 0.231 0.197 0.166 0.137 0.111 0.088
4
INSTRUCTION MANUAL FOR BH-800III MUDP
5
INSTRUCTION MANUAL FOR BH-800III MUDP
3. Structural features
6
INSTRUCTION MANUAL FOR BH-800III MUDP
7
INSTRUCTION MANUAL FOR BH-800III MUDP
higher load. The ring gear, connecting rods and bearings are mounted on the
crankshaft.
The herringbone gear which meshes with the pinion is of interference fit with
the crankshaft, and fastened with bolts and lock nuts.
The big ends of the connecting rods are mounted on the crankshaft via
single-row cylindrical roller bearings while the small ends of them are mounted on
crosshead pins via double-row cylindrical roller bearing.
The crankshaft is mounted on the frame via double-row radial spherical roller
bearings and a bearing sleeve is mounted to protect the bore of the bearing carrier
on the frame. The bearing bore is taper 1:12 for easy assembly and disassembly.
3.2 Fluid End (see Figure 6)
The fluid end consists of three interchangeable fluid cylinders. The suction
valve and discharge valve are separately installed in every cylinder block. Loose
the thread ring(15)bore, remove cylinder(11)head and spring(14),the discharge
valve assy. can be removed. Loose the thread ring, cylinder head, and bolt of
locating ring, turn to 90°the locating ring the suction valve assy. can be removed.
8
INSTRUCTION MANUAL FOR BH-800III MUDP
The three bottom cylinders are connected to the suction manifold by the bolts, the
top cylinders to the discharge cross where there are two outlets, one is used for
connecting discharge screen and pressure gauge, the other for KB45 pulsation
dampener, shear relief valve.
9
INSTRUCTION MANUAL FOR BH-800III MUDP
10
INSTRUCTION MANUAL FOR BH-800III MUDP
11
INSTRUCTION MANUAL FOR BH-800III MUDP
The piston consists of piston hub, rubber cup, plate and snap ring. There are
totally 8 sizes of pistons ranging from 4¡å
to 7¡å
. The piston is fitted with piston rod and
sealed with the seal ring, and tightened with locknuts. After fastening lock nuts, it
not only can prevent the nuts from loosing, but also can seal.
Coupling is used for connecting extension rod to piston rod. The pin hole fit
ensures the concentricity of extension rod and piston rod. The coupling is easy to
assemble and disassemble.
3.2.3 Thread ring, flange and cylinder head
The thread ring and flange are bolted to the cylinder block while thread ring
connects flange by the saw-toothed thread, tightly compressing the cylinder head
and guide sleeve. For disassemble the liner the cylinder head have the bore. With
tightly plate design for guide sleeve(lower),loose the tightly bolt (stainless steel)
turn to 90°the locating ring, the suction valve assy. can be removed.
3.2.4 Valve assy.
API 7¡±valve is used in the valve assy.. The sizes of valve seat and valve pot are
all in compliance with API 7K Spec, and the suction valve and the discharge valve
are interchangeable.
3.2.5 Suction manifold and pulsation dampener
The suction manifold is welded by seamless tube; the desurger is furnished in
it. The pulsation dampener is cast by alloy-steel, built-in diaphragm. It should be
charged with nitrogen effectively to reduce the pulsation of discharge fluid.
3.2.6 Shear relief valve (see Figure 7)
The body of shear relief valve is of alloy-steel casting. The shear relief valve
can assure the safety of the equipment when the working pressure exceeds the
specified pressure. The shear pins are in the same diameter, when regulating
pressure, the shear pin should be inserted to the hole corresponding with the liner
size.
12
INSTRUCTION MANUAL FOR BH-800III MUDP
13
INSTRUCTION MANUAL FOR BH-800III MUDP
shock resistant pressure gauge are mounted on the outlet of the oil pump, The oil
filter is self-sealed construction. So long as the filter screen is removed, the oil
reservoir will be automatically sealed off inside. Therefore it does not need to
release the oil when cleaning the filter screen, the inside of oil reservoir will open
automatically after finishing the wash and installing the filter element in position.
The lube oil pump are designed as a pump that can install in double ended,
installing in the opposite of the power input shaft, the direction of installing see
14
INSTRUCTION MANUAL FOR BH-800III MUDP
figure 8 A-A. The rack both sides all have the motherboard for installing the gear oil
pump, but please attention both sides of the oil pump belts are different. The left
belt pulley position is outboard and the right one is inboard. When changing the oil
pump the direction, you need to change the oil filter head, liquidometer, pump
assembly, guard, suction and flowing lines, and so on..
Lubricant for power end:
Ambient Temperature: -1℃---+68℃ Use N320# mid-extremely pressure gear
oil (6#EP)
Ambient Temperature: -18℃---+27℃ Use N220# mid-extremely pressure gear
oil (4#EP)
Ambient Temperature: -29℃---+4℃ Use N150# mid-extremely pressure gear
oil (1#EP)
Note: The gear oil is sulfur-phosphorus type with 10% 4# compound anti-rust agent
Lubricant capacity: 250L
3.4 Lubrication system of fluid end (see Figure 9)
The lubrication system of fluid end mainly makes fresh water use of
washing and cooling the liner and piston to ensure the piston of normal
reciprocation and to prolong the service life.
The lubrication system consists of independent centrifugal pump,
explosive-proof motor, pipe and water tank. The cooling water is recycling, it is
necessary to clean the water tank and change the water timely.
15
INSTRUCTION MANUAL FOR BH-800III MUDP
16
INSTRUCTION MANUAL FOR BH-800III MUDP
oil has been drained from the power end. Before putting the pump into service, the
following precautions and operations must be performed or checked.
In order to prevent personal injury during maintenance or inspection, this pump
MUST BE SHUT DOWN AND NOT OPERATING, and all the protection devices on
prime movers and drives MUST BE IN SAFE POSITION.
4.1 The base of the BH-800III mud pump is suitable for variety of installations. It
should be noted, however, that the box type construction of the power frame has
high resistance to bending but relatively less resistance against twist. Therefore,
the support under the pump must be level and solid to support the weight and
operating forces exerted by the pump. Additionally, trying to install the coupling,
cardan shaft and chain drive for the input shaft from.
4.2 Suction system requirements
Suction of BH-800III mud pump must have positive pressure for obtaining
satisfactory suction effect, the optimum suction pressure is 0.14MPa to 0.21MPa
(20psi to 30psi) for maximum volumetric efficiency and the longest service life of
the expendable. The positive pressure is supplied from charging pump.
Under some conditions, BH-800III mud pump may work without charging pump,
provided that the fluid level in mud pit is higher than the top of the liner, the viscosity
of the fluid conveyed by the pump is low, suction pipe is short, straight and of at
least the same diameter as suction manifold inlet.
The suction manifold should be piped with valve arrangements so that the
charging pump can be by-passed. So the operation of this mud pump can be
continued in event of charging pump failure which can be improved by replacing the
suction valve spring with a softer spring.
4.3 Caution
Do not pipe the return blow line from the shear relief valve back into the suction
system because the operation of shear relief valve may cause a sudden pressure
rise in the system, resulting in the damage of manifold, suction desurger and
centrifugal pump.
17
INSTRUCTION MANUAL FOR BH-800III MUDP
4.4 Before BH-800III mud pump leaves the factory, the lube oil has been empty
in the pump. So it should be filled with new lube oil before the pump starts, the oil
level is subject to the oil scale, and the first filling should be near the top level. After
running 10 to 15 minutes, stop the pump and add some certain amount of lube oil
again for proper compensation as soon as the oil level is still.
5. Pump application
5.1 Preparation before startup
5.1.1 Fill in the pump with lube oil, the water tank of spay pump with fresh water.
5.1.2 Charge nitrogen in the pulsation dampener at the pressure of 2.5-4.5MPa
(it is not allowed to exceed 2/3 discharge pressure, maximum charging pressure is
4.5MPa).
5.1.3 Plug the shear pin of relief valve in the hole corresponding with the liner
size.
5.1.4 Barring-rotate the crankshaft 3 to 5 turns and check all parts for normal.
5.1.5 Connecting power components.
5.1.6 If the independent lube oil pump is used, first start it for running several
minutes and make sure the system is in good condition, then start the mud pump.
5.1.7 When first running the pump it should be opened the cover and filled lube
oil to guide crosshead pin.
5.1.8 Start up the spay pump and observed the efficiency.
5.2 Pump startup
After being sure everything gets ready, turn on the prime mover and drive the
pump running.
5.3 Pump running
5.3.1 Idle-run the pump 20 to 30 minutes (gradually enhance the strokes and
open idle circulation valve), after the pump has run normally, increase to the
working pressure gradually.
5.3.2 During running, check the pressure of lubrication system for being within
0.1MPa and 0.6 MPa.
18
INSTRUCTION MANUAL FOR BH-800III MUDP
5.3.3 During running, observe pump stroke gauge and make sure the pump
strokes should not be higher than 175 r/min.
5.3.4 During running, observe pump pressure and make sure the pump pressure
should not exceed the pressure of corresponding to the liner size.
5.3.5 During running, observe the operation state of the pump and all the
components. If find any problem, stop the pump and shoot the trouble according to
the instruction. It is prohibited to repair the pump during running.
5.3.6 BH-800III mud pump combines splash lubrication with forced lubrication.
When the input shaft is used to drive the gear oil pump for lubrication, the pump
strokes should not be lower than 30r/min, otherwise the pump lubrication will not be
adequate.
5.4 Stopping the pump
5.4.1 After finishing the operation, slowly reduce the pump pressure value to
zero, then pump the fresh water to wash the discharge manifold until the drained
water become clean when the mud pump can be shut down.
5.4.2 If the pump stops running more than 10 days, you should wash and seal
the fluid end with grease.
5.4.3 If the climate is cold at the temperature of about 0℃, you should drain the
seep in fluid end away to prevent the cylinder from freeze-cracking.
6. Pump maintenance
6.1 Maintenance of power end
Routine inspection of the power end is the most important form of preventive
maintenance and will result in considerable savings by detecting any major trouble
that might be developing and allowing the necessary repairs to be made on a
planned or normal rig-down time.
6.1.1 Bolts and safety wires
Check safety wires and all the bolts including the crankshaft bearing baffle bolts,
connecting bolts, gear hold-down bolts and guide bolts for tightness, replace any
broken wires with new ones after tightening the bolts.
19
INSTRUCTION MANUAL FOR BH-800III MUDP
2) Permanent magnet is installed in the oil filter to absorb the metal substance.
3) A by-pass valve is equipped and can be open automatically to protect the
20
INSTRUCTION MANUAL FOR BH-800III MUDP
21
INSTRUCTION MANUAL FOR BH-800III MUDP
two times replacement. The lubrication oil should be replaced no later than six
months.
Before replacement of lubrication oil, the operator should wash and clean the oil
tank and the guide cavity. Pump the oil by the filter. Inspect the oil pipelines and
make sure there’s no any block in the oil pipelines.
6.1.4 Main bearing cover
Remove the main bearing cover to clean and get rid of any sludge or foreign
materials that might have accumulated at the bottom of the bearing area.
6.1.5 Gear and pinion
Inspect the condition of the gear and pinion teeth for any indications of abnormal
wear. During the initial break-in period there will be some pitting on the gear tooth
surfaces. This is referred to as ¡°initial pitting¡±and is not harmful to the life of the
gear. However, if routine inspection indicates that the degree of pitting continues to
increase, immediately contact the pump manufacturer for a more thorough
inspection of the gear.
6.1.6 Lube oil and oil reservoir
Check the lube oil quality and cleanliness of the oil reservoir. If necessary,
replace the lube oil and maintain the lubrication system as described in the manual.
6.1.7 Maintenance of roller bearings
The roller bearings are used in BH-800III mud pump, they are of precise
machinery parts. Therefore careful maintenance is required in order to obtain the
long service life and high load characteristics.
The main bearings are double-row spherical roller bearings. The pinion shaft is
mounted on the long roller bearings without inner race shoulder. The eccentric
bearings are cylindrical roller bearings with thrust plates on each side to keep the
connecting rod in center line, and the crosshead pin bearings are double-row long
roller bearings.
The inner and outer races of all bearings are assembled by means of very
accurate fits. This accuracy is necessary, for the bearings are to be used again, the
22
INSTRUCTION MANUAL FOR BH-800III MUDP
inner and outer races and the roller assembly of each bearing must be kept
together, and reinstalled exactly as they came off.
It is always necessary to completely replace any roller bearing that fails, even
though only one part of the bearing shows damage. Since the running clearances
of these bearings are extremely small, excessive clearances, worn or grooved
raceways, and any pitting or flaking of the parts is indicative of failure and the entire
bearing should be changed as soon as possible.
Roller bearings are generally assembled to their shafts by means of shrink fits
(Exception of the main bearings which are taper fit, the moving clearance may be
adjustable). Damaged or worn bearings and raceways can be removed by driving
them off the shaft with a copper bar or hammer. They can be cut off the shaft with a
burning torch, but care must be taken not to burn into the shaft. Bearings should
always be heated in an oil bath, the temperature of which should not exceed 149℃
(300oF), being certain that both the oil and the container are very clean. If an
electric heater is used for heating, place a rack into the oil container so that the
bearings will not rest on the bottom. Do not leave the bearings in the oil bath longer
than 10 minutes to avoid the bearing from tempering and softening, shortening the
service life.
The heated bearing should be placed on the shaft immediately and held in
position, and it must be cooled naturally. NEVER USE WATER OR ANY OTHER
LIQUID TO COOL A HOT BEARING. Rapid cooling will cause the bearing
heat-cracking and the bearing will fail immediately.
Before installation, the bearing should be protected from dirt and other foreign
materials at all times. It will be allowed to install only after the bearing is cleaned
with clean kerosene or other solvent and coated with grease.
6.1.8 Installation of pinion assy. (see Figure 3)
Gear shaft is through shaft construction. It support by three same type
bearings and too end size are same.
The pinion shaft is of two-piece combination construction, the left and right hand
23
INSTRUCTION MANUAL FOR BH-800III MUDP
gear shaft .the shaft left and right gears are assembled on the shaft by key.
The running clearances of the bearings are predetermined by their precision fit to
the shaft and the bearing carrier. When performing maintenance or overhaul, make
sure the fits of the bearings should measure up the precision and specification as
shown in design drawing and process.
When installing the pinion shaft assy. in the pump frame, observe the following
precautions:
1). Thoroughly break burrs, dents or gouges from bearing carrier, bearing cap
and bearing surfaces, and wash them clean.
2). First install the right bearing carrier in the frame, then hoist the left input shaft
assembly horizontally and place it into the frame, finally install the right secondary
shaft assembly in position.
3). When installing the bearing carrier and bearing cap, the oil return hole should
be down.
4). Insure all parts should be installed in right position.
5). Tighten bearing bolts to the torque value shown below:
For bolt M16, torque value is 135~170 N.m (100-125ft. lbs).
Check the condition of the pinion bearing inner and outer races and rollers. If
there is any indication of galling, flaking, or if radial clearance exceeds the range
0.20-0.25mm, it is recommended the entire bearing be replaced.
6.1.9 Installation of Crankshaft assy. (see Figure 4)
The crankshaft assembly consists of the crankshaft, ring gear, connecting rod,
bearings and the bearing carriers.
The running clearances of the bearings are predetermined by their precision fit to
the shafts and the bearing carrier bores. When performing any maintenance or
overhaul, make sure the fits of the bearings should measure up the precision and
specification as shown in design drawing and process.
24
INSTRUCTION MANUAL FOR BH-800III MUDP
1). Loosen main bearing bolts and remove the pressure plate
2). Remove the bolts of bearing carrier, two side plates of crankshaft, then press
the bearing carrier by the screws tightly and impose force to the oil hole on the
shaft end by hand-operated pump until the main bearing is taken down.
3). Remove crosshead bolts and eject crosshead pins.
4). Take out crankshaft and connecting rod from the open area by special hoist to
avoid galling the crosshead guide.
6.1.9.2 Assemble the crankshaft in the following manner:
1). Thoroughly clean matching faces of ring gear and flange, and insure the gear
tooth surface is smooth without galling or dent. Tighten the flange by bolts sized
M27 at the torque of 747 Nm (551ft.lbs).
Check the end face and the run-out of the ring gear. If the run-out exceeds
0.15mm, remove the ring gear and find out the cause of misalignment.
2). Install the outer races of the eccentric bearings in the big end eyes of three
connecting rods and the outer race retainer must be positioned. Tighten retainer
bolts and lock them with safety wire.
3). Install the outer race of the crosshead bearings in the small end eyes of three
connecting rods. It is preferred that the outer race assembly be ¡°pressed¡±into
position through ¡°dry ice¡±(CO2) freezing method. Under emergency circumstances,
the outer race assembly can be installed by using a large torch and heating the eye
of the connecting rod. DO NOT EXEED 149℃ AND COOL THE ROD SLOWLY. A
thermoscope can be used.
4). Install the inner race of the crosshead bearing on the crosshead pin (heating
in oil bath) and mark them according to their respective connecting rod positions. It
is prohibited to make them confused.
Note: The inner and outer races of the eccentric bearings are pair-matched and
must not be intermixed.
5). First install inner race of the center eccentric bearing on the shaft, then the
inner races of the other eccentric bearings, and pair-matched installation is a must.
25
INSTRUCTION MANUAL FOR BH-800III MUDP
Finally slide the center rod and the other rods into position. Clear away the foreign
materials in the thread holes and wash the screws, then apply Lock to the screws
and lock them by safety wires. Pay attention to the direction and retainer during
installing the bearing inner races.
6.1.9.3 Installing crankshaft assembly in frame
1). Place three pieces of wooden blocks on three crosshead guides (lower) to
protect the guides from scoring or gouging as the rods are sliding into position.
2). Lift and put the crankshaft (excluding main bearing) into the frame by a
special hoist and link the crossheads to the small end of the connecting rods.
3). Place the main bearing carriers into the crankshaft ends from two sides.
4). Position the crankshaft correctly and adjust the working play of main bearing
on the left side. As the inner diameter of main bearing is taper 1:12, the working
play is adjusted by the shims and should be between 0.062 and 0.193mm, which
can be inspected by depth micrometer.
5). With the same method as described in above item 4, adjust the working play
of main bearing on the right side and keep the clearance of 1.5mm to 2.5mm
between the bearing cap and bearing.
6). During installation, frequently check the rollers in the main bearings for
tightness, the total number of tight rollers could be equal in each row, ensuring that
each bearing is equally loaded.
6.1.10 Installation of crossheads and guides (see Figure 5)
6.1.10.1 The crossheads are generally installed before the crankshaft, maybe
done from the front opening for easy inspection and repair. For the detailed
installation, observe the following procedure and precautions:
1). Thoroughly clean all dirt or contamination and remove all burrs or rough
edges from both sides of the guides and the frame bore where the guides fit. The
contact face between the guide and crosshead should also be polished.
2). If old guides are to be reused, inspect the working surfaces for wear and
scoring streaks. If present, the old guides should be replaced by the new ones.
26
INSTRUCTION MANUAL FOR BH-800III MUDP
3). Install upper and lower guides with the torque value of 200~270N.m
(150~200ft. lbs) and check the fitness between frame and guide to ensure that the
guides fit into frame bore closely, it is inspected with 0.05mm feeler gauge.
4). Push the crosshead in the position by padding the small end of the
connecting rod and rotating the pump. Slide the crosshead pin into its taper bore to
form closest fit by moving the small end of the connecting rod up and down.
5). After the crosshead pin is really put in position, add the adjustable shims
according to the pin protrusion length checked by depth micrometer and apply Lock.
It should be noted that the oil groove opening for crosshead pin baffle is upward.
The screws are tightened with the torque value between 185Nm and 205 Nm.
6). Check running clearance of crosshead by inserting a long feeler gauge
between the crosshead and upper guide. The clearance should be ranged from 0.4
to 0.5 mm. Check with the long feeler gauge over entire surface of crosshead. Less
running clearance can be caused by ¡°swelling¡±from over tightening the crosshead
pin retainer bolts. If present, loosen the crosshead pin and retighten it as per
specified torque value.
7). If the crosshead and lower guide are found slight scoring, the crosshead may
be rotated 180℃ for use. But the scoring area and the taper face between
crosshead pin and crosshead must be ground, and the crosshead pin is not
allowed to change lest the bearing should not be matched.
6.1.10.2 Checking crosshead alignment
The three shaft holes of BH-800III mud pump have been aligned on the basis of
the front wall holes of the frame by the special fixture in the factory. The tolerance
should be ±0.38 mm horizontal, ±0.25 mm vertical. In order for the pistons to
linear-run in the liners, the crosshead alignment should be checked after changing
the guide and crosshead.
1). Take out the piston and check the clamp for precise setting. Based on the
inner bore of the liner, accurately measure the distance from the diaphragm plate
bore to the crosshead extension rod at the top and bottom, front and rear with
27
INSTRUCTION MANUAL FOR BH-800III MUDP
28
INSTRUCTION MANUAL FOR BH-800III MUDP
dirt must be removed from the mating surfaces or boss, otherwise cylinder block
could make up in a cocked or misaligned position. Place the seal rings in position
and be sure that the connecting bolts are reliably tightened with the torque value of
1900 Nm.
7). Suction manifold. The suction manifold is bolted to each cylinder block.
Before installation, thoroughly clean seal groove, the sealing surface on bottom of
the cylinder block in connection flange, and replace seal before bolting manifold
into position. Any burrs and nicks at the groove edges or on the sealing surface
must be repaired.
8). Discharge manifold. The discharge manifold is bolted to each cylinder block
and sealed through the seal in the connection flange. Thoroughly clean the seal
groove, the sealing surface on face of the cylinder block before bolting the manifold
back into position. The flange connection must make up metal-to-metal to retain the
seal, tightening the bolts to torque values of 1055Nm (778 ft.lbs).
9). Charging instructions of pulsation dampener (see Figure 11)
A set of charging device (including charging hose assembly) will be supplied with
the pump during delivery, charging procedures should be followed below:
1). Remove dampener gauge cover and bleed off any existing pressure in the
gauge area by turning purge valve cap approximately 1/4 to 1/2 turn. Then remove
purge valve.
2). Connect charging hose to dampener charging valve and nitrogen cylinder
valve.
3). Open dampener charging valve.
4). Slowly open the cylinder valve to regulate nitrogen flow to dampener by this
valve.
5). When the dampener pressure gauge shows the desired charging valve
pressure, close nitrogen cylinder valve and dampener valve.
6). Remove the hose from dampener charging valve and install purge valve.
For best results, dampener pre-charge pressure should be not more than 2/3 of
29
INSTRUCTION MANUAL FOR BH-800III MUDP
pump discharge pressure. Maximum pre-charge pressure is 650 PSI (4.5 MPa).
WARNING:
1). USE ONLY NITROGEN OR COMPRESSED AIR; DO NOT CHARGE WITH
OXYGEN OR OTHER INFLAMMABLE GAS.
2). WHEN MAINTAINING THE DAMPENER, THE PUMP PRESSURE AND
DAMPENER PRESSURE MUST LOWER TO ZERO.
30
INSTRUCTION MANUAL FOR BH-800III MUDP
not enough. The polluted water should be changed and the water tank should be
cleaned.
5). Check if the pressure of discharge pulsation dampener meets the
requirements ranged from 2.5 to 4.5 MPa.
6). Check the lube oil pump for the variation of pressure gauge, if the pressure is
very low (lower than 0.035MPa) or no pressure, check if the suction filter screen
are plugged.
7). Check the reliability of shear relief valve, if necessary, they should be
changed.
8). Loose the coupling of piston rod every day, check if the pyramidal face of
coupling and the junction face of piston rod and extension rod are clean, rotate the
piston rod a quarter round and tighten it. The purpose of doing that is to make the
wearing face evenly and prolong the service life of liner and piston.
9). Check the bolt 1/2¡±
-13UNC of suction valve (see fig 6 item 20),if it’s loosing
it should be tighten it .before tightening the valve bonnets and cylinder heads, coat
the lubricating grease on the threads and check them for loosing.
10). Check thread ring seal, liner seal and extension rod seal, if the mud
discharges, the relative seal ring should be changed.
7.2 Weekly maintenance
1). Disassemble the valve bonnets and cylinder heads and clean them every
week, meanwhile coat the molybdenum disulfide complex calcium base grease.
Check the inner sleeves (rubber) of valve guide, if there is obvious abrasion, and
the clearance is too big, it should be changed to avoid the guide failing to guide
sleeves the valve motion in the right way and accelerating the abrasion of valve.
2). Check the valve and valve seat change the worn or pierced valve body, valve
rubber and valve seat. Check the valve spring and change the broken or inelastic
spring.
The valve seat puller (see Figure 12) is supplied with the pump to take out the
valve seat. The usage is that the valve seat puller, after putting into the seat, hang
31
INSTRUCTION MANUAL FOR BH-800III MUDP
up the bottom of the seat. Then screw nut M42 x 3 and strike the top cylinder block
and the end of screw 1 5/8¡±
-8UN by a copper bar at the same time, in this case
the valve seat will be pulled out.
3). Check the locknuts of piston. The corrosive or damaged locknuts should be
changed. The seal rings in the locknuts will fail and should be changed after the
locknuts are tightened three or four times.
4). Check and clean the filter screen in the lubrication system.
7.3 Monthly maintenance
1). Check all the stud bolts and nuts of fluid end, for example, bolts and nuts
among cylinders, bolts and nuts connecting the valve bonnet and flange, the bolts
and nuts on discharge manifold. If they are loose, they should be tightened to the
specified torque value.
2). Check the seal rings in the packing box of extension rod. The worn one
should be changed. Usually, change it at least once every three months. Attention
should be taken to the oil seal position when changing (the lip should be inward).
3). Remove and clean the discharge manifold.
4). Change the dirty lube oil in the power end once every six months and clean
the oil pool and fill in new oil at the same time.
7.4 Yearly maintenance
1). Check if the crosshead and guide are loose, if the crosshead running
clearance conforms to requirements. The clearance can be adjusted by adding
shim under the guide, see Clause 6.1.10 Installation of crossheads and guides.
2). Check the whole pump completely every two years, check if the main bearing,
connecting rod bearing, crosshead bearing, input shaft bearing are worn or
damaged. They should be changed if they can not be used any more.
3). Check the wear or pitting of gear, if worn sharply, the ring gear should be
replaced.
7.5 Cares should be taken for the following in maintenance
1). When connecting the extension rod and piston rod, the setting pin bore and
32
INSTRUCTION MANUAL FOR BH-800III MUDP
3). After stopping the pump in winter, the mud in the valve compartment and liner
should be discharged and cleaned completely, then apply the lubricating grease to
valve and liner.
4). The discharge pulsation dampener is only allowed to charge inert gas (such
as nitrogen) or air. No inflammable and explosive gases are allowed such as
oxygen and hydrogen, etc.
33
INSTRUCTION MANUAL FOR BH-800III MUDP
8. Troubleshooting
8.1 Trouble and troubleshooting of fluid end
Trouble Cause Troubleshooting
1. The pressure readings become 1.The charging piping is not sealed off and the 1. Tighten the flange bolts of charging piping
low and the displacement air gets in the pump. or change the shim.
reduces or no mud discharged. 2.The suction filter screen is plugged. 2. Stop the pump and clean the suction filter
screen.
2. Uneven discharge. The 1. A piston or a valve is worn out or damaged. 1. Change the damaged piston and check if
pressure gauge fluctuates. The 2. There is air in the pump cylinder. the valve is damaged or plugged.
charging piping has abnormal 2. Check if the charging piping and valve
3.There is severe slap in the liner. 1.The piston nuts are loose. 1.Tighten the piston nuts.
3.The suction is not good to cause water dash. 3.Find out the reason of improper suction.
4.The mud leakage from thread 1.The thread ring is not tightened. 1.Tighten thread ring 1 and thread ring 2.
ring 1, thread ring 2 and liner 2.The seal ring is damaged. 2.Change the seal ring.
seal.
5. The pulsation dampener can’t 1.The charging connector is plugged. 1.Clean the connector.
be charged or it leaks after 2.The diaphragm of the pulsation dampener is 2.Change the diaphragm.
1..Overheat of 1.The oil pipe or oil port is plugged. 1. Clean the oil pipe or oil port.
4.The lube oil is too much or too little. 4. Add proper amount of oil.
2. There is slap 1. The crosshead guide is worn out sharply. 1. Adjust the clearance or change the
34
INSTRUCTION MANUAL FOR BH-800III MUDP
9. Expendables list
ITEM PART NO. DESCRIPTION QTY PER MOUNTING POSITION
PUMP
35
INSTRUCTION MANUAL FOR BH-800III MUDP
PUMP
7 NB-07Y-07GJ 1 ¡±
/ 1 1/8¡±hammer 1
spanner
spanner
spanner
36