Академический Документы
Профессиональный Документы
Культура Документы
32LG40
Model : 32LG40 32” CLASS LCD HDTV
w/ BUILT-IN DVD PLAYER
(31.5" diagonal)
Direct View LCD
With built in DVD Player
Original 08/12/2008
Updated 10/13/2010
OUTLINE
Section 1
Contact Information, Preliminary Matters, Specifications,
LCD Overview, General Troubleshooting Steps,
Signal Distribution, Disassembly Instructions and Voltages
Section 2
Circuit Board Operation, Troubleshooting of :
• Switch mode Power Supply
• Main (Digital) Board
• T-CON Board
• Ballast Board
Section 1
This Section will cover Contact Information and remind the Technician of Important Safety Precautions for
the Customers Safety as well as the Technician and the Equipment.
Basic Troubleshooting Techniques which can save time and money sometimes can be overlooked. These
techniques will also be presented.
This Section will get the Technician familiar with the Disassembly, Identification and Layout of the LCD
Display Panel.
At the end of this Section the Technician should be able to Identify the Circuit Boards and have the ability
and knowledge necessary to remove and replace safely any Circuit Board or Assembly.
Caution
To avoid personal injury, disconnect the power before servicing this product. If electrical power is required for
diagnosis or test purposes, disconnect the power immediately after performing the necessary checks. Also be
aware that many household products present a weight hazard. At least two people should be involved in the
installation or servicing of such devices. Failure to consider the weight of an product could result in physical
injury.
Today’s sophisticated electronics are electrostatic discharge (ESD) sensitive. ESD can weaken or damage
the electronics in a manner that renders them inoperative or reduces the time until their next failure.
Connect an ESD wrist strap to a ground connection point or unpainted metal in the product. Alternatively,
you can touch your finger repeatedly to a ground connection point or unpainted metal in the product. Before
removing a replacement part from its package, touch the anti-static bag to a ground connection point or
unpainted metal in the product. Handle the electronic control assembly by its edges only. When
repackaging a failed electronic control assembly in an anti-static bag, observe these same precautions.
Regulatory Information
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy, and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate
the receiving antenna; Increase the separation between the equipment and the receiver; Connect the
equipment to an outlet on a different circuit than that to which the receiver is connected; or consult the
dealer or an experienced radio/TV technician for help.
LCD-DV: 32LG40, 32LH30, 37LH55, 42LG60, 42LG70, 42LH20, 42LH40, 42LH50, 42LH90, 42SL80,
47LG90, 47LH85, 42LE5500, 47LE8500
PLASMA: 42PG20, 42PJ350, 42PQ20, 42PQ30, 50PG20, 50PJ350, 50PK250, 50PK750, 50PS80,
50PS60, 60PK750, 60PS11, 60PS60, 60PS80
1. Check the appearance of the Replacement Panel and Circuit Boards for both physical damage
and part number accuracy.
2. Check the model label. Verify model names and board model matches.
3. Check details of defective condition and history. Example: Oscillator failure dead set, etc…
•Define Look at the symptom carefully and determine what circuits could be causing
the failure. Use your senses Sight, Smell, Touch and Hearing. Look for burned parts and
check for possible overheated components. Capacitors will sometimes leak dielectric material
and give off a distinct odor. Frequency of power supplies will change with the load, or listen for
relay closing etc. Observation of the front Power LED may give some clues.
•Localize After carefully checking the symptom and determining the circuits to be
checked and after giving a thorough examination using your senses the first check should
always be the DC Supply Voltages to those circuits under test. Always confirm the supplies
are not only the proper level but be sure they are noise free. If the supplies are missing check
the resistance for possible short circuits.
•Isolate To further isolate the failure, check for the proper waveforms with the
Oscilloscope to make a final determination of the failure. Look for correct Amplitude Phasing
and Timing of the signals also check for the proper Duty Cycle of the signals. Sometimes
“glitches” or “road bumps” will be an indication of an imminent failure.
•Correct The final step is to correct the problem. Be careful of ESD and make sure to
check the DC Supplies for proper levels. Make all necessary adjustments and lastly always
perform a Safety AC Leakage Test before returning the product back to the Customer.
Side View
This section of the manual will discuss the specifications of the 32LG40
“Thin” LCD Direct View Display Panel.
•720p HD Resolution
• 12,000:1 Dynamic Contrast Ratio
• Side-loading Progressive Scan DVD Player
• Super Multi-Format
• 3x HDMI™ 1.3
• AV Mode (Cinema, Sports, Game)
• Clear Voice
• SimpLink™ Connectivity
• Invisible Speaker System
• Expert Mode
• PC Input
• Swivel Stand (Manual)
FORMATS BASIC
NTSC 480I Interlaced 240 Lines PIXEL COUNTS
SD 480P Progressive 480 Lines
HD 1080I Interlaced 540 Lines
HD 720P Progressive 720 Lines
HD 1080P Progressive 1080 Lines 720P Panel
1365 (H) × 768 (V)
MUTE
1 2 3
4 5 6
7 8 9
LG
RS232 USB
Service Only
Audio HDMI
Remote Out
In
Composite
A/V
Component Composite
Y Pr/Pb
Main Board
Orientation
15 LCD DV August 2008 32LG40
Accessing the Service Menu
SIDE KEYS
REMOTE To access the Service Menu.
TOP PORTION 1) Turn the Set On
2) Simultaneously, Press and
“Hold” the Menu Key on the
Side Key pad and Press and
“Hold” the Menu Key on the
Remote approximately 5
seconds.
3) If Customer’s Menu appears,
continue to hold until it
disappears.
4) The Service Menu appears
Shows the
Currently
Installed
Version
Shows the
2) Copy new software (xxx.epk) to "LG_DTV" Software
folder. Make sure to have correct software file. Version
3) With TV turned on, insert USB flash drive. found on the Shows the
4) You can see the message USB Flash Software file found
“TV Software Upgrade” (See figure to right) Drive on the USB Flash
5) Cursor left and highlight "START" Button and Drive
push “Enter” button using the remote control.
6) You can see the download progress Bar. * CAUTION:
7) Do not unplug until unit has automatically Do not remove AC power or the USB Flash Drive.
restarted. Do not turn off Power, during the upgrade
8) When download is completed, you will see process.
“COMPLETE”.
9) Your TV will be restarted automatically.
The Stand does not need to be removed. Remove the 18 screws shown by arrows.
Pay attention to the size and type of screw as there are many different types.
Putting in the improper screw when reassembling may Cause damage.
T-CON p/n
EAT56801301
Ballast p/n
EAY56797501
LVDS
Cables
Side Side
Controls Inputs
Speaker rattle.
Speakers 1) Tighten screws at bottom of cabinet
2) Tighten screws holding woofers
Tweeters Tweeters
Speaker rattle.
1) Tighten screws at bottom of cabinet
2) Tighten screws holding woofers
Stand Removed
F101
3.15A/250V
334V Actual
F100
5A/250V
AC IN Hot Ground
AC IN
To Main
To Ballast P203
Error 14
WM-D1 13 16.5V 2 1 16.5V
INV On/Off 12 Gnd 4 3 Gnd
BR1 11 12V 6 5 12V
Gnd 10 Gnd 8 7 Gnd
Gnd 9 5.2V 10 9 5.2V
Gnd 8 5.2V 12 11 5.2V
Gnd 7 Gnd 14 13 Gnd
Gnd 6 Gnd 16 15 Gnd
24V 5 ACD 18 17 ERROR
24V 4 INVOn/Off 20 19 POWER-ON
24V 3 PWR-DIM 22 21 BR1
24V 2 n/c 24 23 fixedV
24V 1
F100 F101
5A/250V 3.15A/250V
AC IN 334V Actual
AC IN
With Power Supply disconnected from other Boards and AC applied, confirm
that the Power Supply is producing 5V from either Pins 9, 10, 11 or 12. If
not, check fuse. If fuse OK and no 5V, replace Power Supply. If 5V OK
then continue.
1st short either pin 9, 10, 11 or 12 (5V) to Pin 19 (PWR) using a 10K
resistor.
+5V This turns on the power supply.
Confirm that the other low voltage power supplies are activated.
Pins 1 and 2 (16V)
Pins 5 and 6 (12V)
Pin 18 (AC Detect) goes high
Fuse F101 Check for 350V (Ballast Voltage)
If any voltage missing, replace Power Supply.
If the 1st test was successful, continue. Leave original 10K in place.
2nd: To test the Backlights, leave the 10K jumper in place. Plug up the Back
light plug P203. Apply AC Power.
+5V If no backlight activity, confirm the Fuse F101 has approx. 350V on both sides.
If on one side, check fuse for open.
If no 350V, replace Power Supply.
Ballast will not run if either of the Backlight plugs are removed.
Disconnect P203,
P201 and AC In
Remove the 4
screws indicated in
the red circles.
Diode Diode
Pin Label STBY Run Pin Label STBY Run
Check Check
23 N/C 0V 3.2V OL 24 N/C 0V 0V OL
21 BR1 0V 1.68V OL 22 PWM-DIM 0V 3.38V OL
19 PWR 0V 2.86V OL 20 INV On/Off 0V 3.29V OL
17 ERR Gnd Gnd 1.26V 18 ACD 5.05V 4.57V OL
15 Gnd Gnd Gnd Gnd 16 Gnd Gnd Gnd Gnd
13 Gnd Gnd Gnd Gnd 14 Gnd Gnd Gnd Gnd
11 5.2V 5.15V 5.15V 0.34V 12 5.2V 5.15V 5.15V 0.34V
9 5.2V 5.15V 5.15V 0.34V 10 5.2V 5.15V 5.15V 0.34V
7 Gnd Gnd Gnd Gnd 8 Gnd Gnd Gnd 0V
5 12V 0V 11.8V 1.69V 6 12V 0V 11.8V 1.69V
3 Gnd Gnd Gnd Gnd 4 Gnd Gnd Gnd Gnd
1 16.5V 0V 16V 0.31V 2 16.5V 0V 16V 0.31V
To If odd Video
Power problems are
IC809 A2.6V BCM Reg
IC302
IC300
IC303
IC301
IC304
found, use some
P800 DDR VTT freeze spray
Reset
BCM
about IC100 and
To DVD
Dual Data its circuits,
Registers
IC400 BCM Reset IC101
IC807 5V Reg If video returns to
Flash Q800 SIF
P901 IC407 Micro
normal, Board
Memory
BCM IC803 9V Reg
needs to be
To DVD X400
24Mhz
IC800 replaced.
IC100 CVBS
Q400 Micro Reset Amp
P900 BCM IC201
IC405 Micro Reset USB
3.3V
Q802 5V Sub Switch Control X200
To DVD IC802 3.3V Reg 54Mhz
Q801 5V
Sub Switch TUNER USB
P904 LD800
IC502
Audio Selector
HDMI
IC806 IC600
To A3.3V HDMI Selector
BCM
Ft Keys IC602 HDMI EDID IC402
Serial Port
P401 Interface
IC601 HDMI EDID
Side
To SPK Inputs
P500
IC501 Audio Processor
and Output
16V Pins 49~52
PIN FUNCTION NAME STBY RUN PIN FUNCTION NAME STBY RUN
3 On/Off Control BCM DDR Power 0V 3.4V 2 Gnd Gnd Gnd Gnd
IC400 RESET GENERATOR TO IC401 3.3BCM (On Back) PIN FUNCTION NAME STBY RUN
X200
16 IC406
Micro P900
IC805 A1.2V BCM Reg
EEPROM
Silk Screen for Pin 1 wrong IC805
TUNER
TU800
IC801 1.8V Reg
P904
IC102
1 HDCP IC403
KEY NVRAM
IC408
SIF Select
DVD/BCM IC702
EEPROM
P401
Side IC701
Side
Inputs HDMI
EDID
P500
PIN FUNCTION NAME STBY RUN PIN FUNCTION NAME STBY RUN
1 On/Off Control Reset from IC400 0V 3.4V 3 OUT 3.3VST_MICON 3.43V 3.43V
PIN FUNCTION NAME STBY RUN PIN FUNCTION NAME STBY RUN
PIN FUNCTION NAME STBY RUN PIN FUNCTION NAME STBY RUN
11,12,18,
Gnd Gnd Gnd Gnd
19,20
Screen Print for Pin No is incorrect, use IC
IC407 X400
Micro 2.4Vp/p
24Mhz
1.49V
1.49V
MAIN
Board
1.49V
Main Board Only when set is on
X200 Location TP Use Crystal Side R232 or R233
Pin 14
“SIF”
Signal
850mVp/p
Pin 16
“Video”
MAIN
Signal
Board
To confirm that the Main Board is outputting Picture Content signals, check P902 (LVDS) cable for
output. Check 11~20. This signals vary from each other, but looking for signals like the ones
shown below on any of these pins confirm the output of video content.
This signal is using standard SMTE Color Bar output from a generator as the input source.
MAIN
Board
Pin 16
For Locations
See Main Board
Back Side View
LVDS 12V
LVDS Signal
Waveforms
Shown on back of
Interconnect
Diagram
Diode Diode
Pin Label SBY Run Pin Label SBY Run
Check Check
1 LVDS 12V 0V 12.3V OL 2 LVDS 12V 0V 12.3V OL
3 LVDS 12V 0V 12.3V OL 4 LVDS 12V 0V 12.3V OL
5 Gnd 0V 0V Gnd 6 Gnd 0V 0V Gnd
7 Gnd 0V 0V Gnd 8 Gnd 0V 0V Gnd
9 Gnd 0V 0V Gnd 10 Gnd 0V 0V Gnd
11 LVDS 0V 1.2V 0.98V 12 LVDS 0V 1.1V 0.98V
13 LVDS 0V 1.2V 1.11V 14 LVDS 0V 1.05V 1.06V
15 LVDS 0V 1.1V 1.06V 16 LVDS 0V 1.09V 1.05V
17 LVDS 0V 1.08V 1.11V 18 LVDS 0V 1.13V 1.06V
19 LVDS 0V 1.14V 1.11V 20 LVDS 0V 1.06V 1.06V
21 n/c 0V n/c OL 22 n/c 0V n/c OL
23 n/c 0V n/c Gnd 24 n/c 0V n/c OL
25 Size Sel 0.4V 3.07V 3V 26 Gnd 0V 0V Gnd
Diode
Pin Label STBY Run
Check
1 KEY3 3.4V 3.4V 1.4V
2 KEY4 3.4V 3.4V 1.4V
3 Gnd 0V 0V Gnd
4 Gnd 0V 0V Gnd
5 KEY-1 3.4V 3.4V 1.4V
6 KEY-2 3.4V 3.4V 1.4V
7 n/c 0V 0V OL
8 ST-5V 5V 5V 0.53V
9 PWM-LED 0V 0V 0.8V
10 IR 4.1V 4.1V 2.3V
11 n/c 0V 0V OL
12 Gnd 0V 0V Gnd
13 LED-G 0V 2.1V 0.8V
14 LED-R 2.1V 0V 0.8V
15 Gnd 0V 0V Gnd
Diode Diode
Pin Label SBY Run Pin Label SBY Run
Check Check
1 n/c 3.34V 3.34V OL 14 n/c 0V 0.7V OL
2 Disc Chedk *3.3V * 3.3V 1.60V 15 n/c 0V 0V OL
3 n/c 3.34V 3.3V OL 16 DVD-SPDIF 3.38V 1.8V 0.83V
4 n/c 3.34V 3.3V OL 17 DVD-MUTE 0V 0V OL
5 Gnd 0V Gnd Gnd 18 DVD-L-In2 0V 2.4V OL
6 Pr 0V 0.8V OL 19 Gnd 0V 0V Gnd
7 Pb 0V 0.8V OL 20 DVD-R-In2 0V 2.4V OL
8 Y 0V 0.6V OL 21 n/c 0V 0V OL
9 Gnd 0V 0V Gnd 22 Gnd 0V 0V Gnd
10 n/c 0V 0V OL 23 n/c 0V 0V OL
11 Gnd 0V 0V Gnd 24 n/c 0V 0V OL
12 n/c 0V 0V 0.83V 25 Gnd 0V 0V Gnd
13 Gnd 0V 0V Gnd 26 n/c 0V 0V OL
P900 Connector "Main" to P402 "DVD Player" P901 Connector "Main" to CN400 "DVD Player"
Pin Label SBY Run Diode Check Pin Label SBY Run Diode Check
1 Disk-Enable *3.4V *3.4V 1.68V 1 12V 0V 12.3V 3V
2 DVDP-RXD 0.7V 3.08V 3V 2 Gnd 0V 0V Gnd
3 DVDP-TXD 0.7V 3.4V 3V 3 DVDP 3.3V 3.4V 3.37V .099V
4 Gnd Gnd 0V Gnd 4 Gnd 0V 0V Gnd
5 Gnd 0V 0V Gnd
*Pin 1: 3.4V with No Disc and 0V with Disc inserted
6 5V 0V 5.01 0.45V
F1
8A/125V
Transformers
To Backlight
Left Side
To Backlight
Right Side
MCN1
F1
8A/125V
Transformers
To Backlight To Backlight
Left Side Right Side
Primary
Side Warning,
secondary is
over 1.2Kv
Transformers
PWMDIM Waveform
manipulates Just for
the Burst Explanation,
Triangle taken from a
Oscillator in different
the ballast chassis.
drive IC.
ADIM also
manipulates
the Burst
Triangle
Oscillator
But it is not
used.
Sh
Heat Transfer Material iel
d
Be sure to
replace “All”
heat sink
materials and
insulators.
Protects the
Outputs
Alignment
Notch
Insulator
Shiny Side
Down
(Conductive)
Cut Out
1 VBL 0V 24.52V OL
2 VBL 0V 24.52V OL
3 VBL 0V 24.52V OL
4 VBL 0V 24.52V OL
5 VBL 0V 24.52V OL
11 BVR_A 0V 1.67V OL
12 On/Off 0V 3.45V OL
13 VBR_B 0V 3.40V OL
Remove
Screw
Remove
Screw
Remove
Screw CN1 LVDS
To Main
CN2 CN3
US2
12V
F1
6.3V/1.5A
US2 3) 0.0V
CN1 LVDS
2) 1.8V
Use the Connector P902 on Main
Board for Voltages and Signal To Main
1) 3.3V
Readings
* The Voltages on CN2 and CN3 must be present for the panel to operate.
Press in Press in
LVDS Connectors
Press in from the sides and lift out.
Diode Diode
Pin Label SBY Run Pin Label SBY Run
Check Check
1 LVDS 12V 0V 12.3V 2.9V 2 LVDS 12V 0V 12.3V 2.9V
3 LVDS 12V 0V 12.3V 2.9V 4 LVDS 12V 0V 12.3V 2.9V
5 Gnd 0V 0V Gnd 6 Gnd 0V 0V Gnd
7 Gnd 0V 0V Gnd 8 Gnd 0V 0V Gnd
9 Gnd 0V 0V Gnd 10 Gnd 0V 0V Gnd
11 LVDS 0V 1.2V 0.88V 12 LVDS 0V 1.1V 0.88V
13 LVDS 0V 1.2V 0.88V 14 LVDS 0V 1.05V 0.88V
15 LVDS 0V 1.1V 0.88V 16 LVDS 0V 1.09V 0.88V
17 LVDS 0V 1.08V 0.88V 18 LVDS 0V 1.13V 0.88V
19 LVDS 0V 1.14V 0.88V 20 LVDS 0V 1.06V 0.88V
21 n/c 0V n/c n/c 22 n/c 0V n/c n/c
23 n/c 0V n/c n/c 24 n/c 0V n/c n/c
25 Size Sel 0.4V 3.07V OL 26 Gnd 0V 0V Gnd
Remove
Tape
CN402
CN401
CN400
CN400 Connector "DVD" to P901 "Main" CN402 Connector "DVD" to P900 "Main"
Pin Label STBY Run Diode Check Pin Label STBY Run Diode Check
1 P12V 0V 12.3V 3.22V 1 GP101 *3.4V *3.4V OL
2 Gnd Gnd Gnd Gnd 2 TXD1 0.7V 3.08V OL
3 P3.3V 3.4V 3.37V 0.78V 3 RXD1 0.7V 3.4V OL
4 Gnd Gnd Gnd Gnd 4 Gnd Gnd Gnd Gnd
5 Gnd Gnd Gnd Gnd
6 P5V 0V 5V 1.2V
*Pin 1: 3.4V with No Disc and 0V with Disc inserted
ZD1
5V Zener
ZD2
4.1V Zener
J2 J1
To Side Keys Board ZD3 To Main Board
3.4V Zener
POWER
LED
IR Receiver
POWER
BUTTON
10 IR 4.1V 4.1V OL
11 n/c 0V 0V OL
12 Gnd 0V 0V Gnd
15 Gnd 0V 0V Gnd
2 Gnd 0V 0V Gnd
4 Gnd 0V 0V Gnd
6 Gnd 0V 0V Gnd
8 Gnd 0V 0V Gnd
This section shows the 11X17 foldout that’s available in the Paper
and Adobe version of the Training Manual.
IC808
Power Supply
CN402 BSM
22V p/p 34V p/p P901 IC803
IC407 IC400
6 1 6 1 CN401 Micro
X400 IC00
3.15A / 250V Rating Q400 24 Mhz BCM
DVD Drive 334V Actual Reading IC405 1.5V X200
P900 1.5V
F101 1.5V
T1 T2 IC805
IC801
5A / 250V 54 Meg
P904 TUNER
A/C Fuse
F100 LD800 IC802
IC801
CN400 IC806
Secondary over 1.2Kv L
A/C In
SC100
To Backlight N
Left Side P401
To Backlight
Grayed Out ICs are
Right Side located on Back
P500 To Speakers
Front PWB IC401 BCM IC100 Reset IC808 ST-BY 3.3V DC-DC Converter
Side (Key) Controls
IC201 USB Power IC405 Reset Generator for Q400 Micro Reset IC806 D3.3V/A3.3V_BCM Regulator turns on LD800 Q801 5V Sub Switch
PIN FUNCTION NAME STBY RUN PIN FUNCTION NAME STBY RUN
Assembly PIN
2
FUNCTION
IN
NAME
+5V
STBY RUN PIN
0V 5V 1
FUNCTION
IN
NAME STBY RUN
3.3V_MICON 3.41V 3.41V
PIN
1
FUNCTION NAME
On/Off Control Power_CTL_3.3V
STBY RUN PIN
0V 3.4V 1,3
FUNCTION
IN
NAME
ST_5V
STBY RUN
0V 5V 14 IN D3.3V_BCM 0V 3.41V 2 IN ST_5V 5V 5V
(Interface) 3
7
On/Off Control BCM DDR Power
OUT USB_PWR_Out_1 0V
0V 3.4V
5V
2
3
Gnd
OUT
Gnd
Reset (Lo-Hi)
Gnd Gnd
0.6V 0.6V
2
3
IN
Gnd
+5V_SUB
Gnd
0.36V 5V 2,4 On/Off Control
Gnd Gnd 5,6,7,8 OUT
Q802
+5V_SUB
0V 0.28V
0V 5V
1
6
On/Off Control Reset from IC400
OUT BCM_RESET
0V
0V
3.4V
3.4V
3
4
OUT
Gnd
3.3VST_MICON
Gnd
3.43V 3.43V
Gnd Gnd
J2 J1 8 OUT +3.3V 0V3.1V IC802 +3.3V Regulator (3.3V TMDS_SW) 4 OUT D3.3V_BCM 0.1V 3.4V Q802 5V Sub Switch Controller for Q801 IC801 +1.8V_NTP Regulator Q900 Controller for LVDS 12V Switch Q901
IC304 2.6V BCM PIN FUNCTION NAME STBY RUN IC807 D3.3V_BCM Regulator (Also A3.3V_BCM) PIN FUNCTION NAME STBY RUN PIN FUNCTION NAME STBY RUN PIN FUNCTION NAME STBY RUN
IR Receiver PIN FUNCTION NAME STBY RUN 1 Gnd +3.3V 0V 5V PIN FUNCTION NAME STBY RUN B On/Off Control RL_ON 0V 3.29V 1 Gnd Gnd Gnd Gnd B Control LVDS_PANEL_CTRL 0V 0.75V
3,8 OUT DDRO_VTT 0V 1.29V 2 OUT Gnd Gnd Gnd 1 IN +9V 0V 8.9V C Pull Down ST_5V 0V 5V
Power Button 2 OUT +1.8V_NTP 0V 1.8V C Pull Down 12V LVDS Switch Control 0V 0V
5,6,7 IN D2.6V_BCM 0V 2.6V 3 IN +5V_SUB 0V 3.2V 2 On/Off Control Power_CTL_3.3V 0V 3.4V E Gnd Gnd Gnd Gnd
3 IN 3.3V_TMDS_SW 0.26V 3.29V E Gnd Gnd 0V 0V
4 On/Off Control DDRO_VTT 0V 1.29V IC803 +9V Regulator 3 OUT +5V 0V 5V Q400 Reset Generator for MICRO IC407
IC805 D1.2V/A1.2V BCM Regulator Q901 LVDS 12V Switch
IC400 Reset Generator for IC401 3.3V BCM (On Back) PIN FUNCTION NAME STBY RUN 4 n/c n/c n/c n/c PIN FUNCTION NAME STBY RUN
PIN FUNCTION NAME STBY RUN 1 IN +12V 0V 12V 5 Gnd Gnd Gnd Gnd B Reset Reset 0.6V 0.6V PIN FUNCTION NAME STBY RUN PIN FUNCTION NAME STBY RUN
1 IN D3.3V_BCM 0V 3.4V 2 Gnd Gnd Gnd Gnd D2.6V_BCM Regulator (Also A2.6V_BCM) C Vcc 3.3VVST_MICON 0V 0V 6,7,8,10 IN +5V_SUB 0.38V 5V 1,3 IN 12V 0V 12.36V
IC809
2 Gnd Gnd Gnd Gnd 3 OUT +9V 0V 9V PIN FUNCTION NAME STBY RUN E Gnd Gnd Gnd Gnd 17 On/Off Control Power_CTL_1.2V 0V 3.41V 2,4 On/Off Control Q900 0V 6.16V
3 OUT Reset (Lo-Hi) 0V 3.39V 6,7,8,10 IN +5V_SUB 0.36V 4.98V 1,2,3,4,5 OUT D1.2V_BCM 0V 1.29V 5,6,7,8 OUT LVDS 12V 0V 12.36V
P101 17 On/Off Control Power_CTL_2.6V 0V 3.41V 13, 14,15,16 n/c n/c 0V 0V
1,2,3,4,5 OUT D2.6V_BCM 0V 2.66V 11,12,18,
14,15 n/c n/c n/c n/c
REGULATORS/ICs ON FRONT 19,20 Gnd Gnd Gnd Gnd REGULATORS/ICs ON BACK
11,18,19,20 Gnd Gnd Gnd Gnd Screen Print for Pin No is incorrect, use IC
32LG40 LVDS P902 WAVEFORMS