Академический Документы
Профессиональный Документы
Культура Документы
Synco™ 200
Use
For use on basic to complex ventilation, air conditioning and chilled water plant.
The universal controllers are designed to handle the following controlled variables:
Temperature, relative/ absolute humidity, pressure/ differential pressure, airflow,
indoor air quality and enthalpy.
CE1N3101en
2016-03-22 Building Technologies
Functions
Operating modes Selection of operating mode via status inputs: Comfort, Economy, Protection
Display of current operating mode (Comfort, Economy, Protection)
Setpoints With each sequence controller: Individually adjustable heating and cooling
setpoints (or maximum and minimum setpoints) for the Comfort and Economy
modes
Predefined room temperature setpoint with room unit or setpoint readjuster
(passive)
With each sequence controller: Predefined setpoint with remote setpoint adjuster
(active or passive)
Room temperature setpoint with summer and/ or winter compensation
With each sequence controller: Setpoint shift depending on sensor signal,
selectable start and end points
Universal inputs Universal inputs for:
Passive or active analog input signals of various measured values (°C, %, ---)
Digital input signals (potential-free contacts)
Control functions Universal controller (sequence controller) for 2 heating sequences (reverse
acting) and 2 cooling sequences (direct acting), can be used as a controller
providing P-, PI or PID mode, or as a differential controller
Controller can be configured as a room / supply air temperature cascade
controller with limitation of the supply air temperature
Each sequence can be assigned modulating control (modulating output, step
switch, mixed air damper/ heat recovery equipment) and a pump. 2 sequences
can act on the same modulating control (e.g. priority cooling/ dehumidification)
General limitation (minimum/maximum with PI mode per sequence controller,
either as absolute limitation, e.g. for the supply air temperature or supply air
humidity), or as relative temperature limitation (e.g. maximum limitation of the
room / supply air temperature differential). Limitation acts on all sequences.
Minimum limitation can be set to a lower setpoint while cooling is on (e.g cooling
with DX cooler battery)
Sequence limitation with PI mode per universal controller, can be defined as
minimum or maximum limitation. Limitation acts on a single sequence (e.g. heat
recovery anti-icing protection or maximum limitation of the heating coil’s return
temperature)
The mixed air temperature controller controls the mixed air temperature via the
air dampers
Locking of individual sequences
Digital input (heating limit switch, from a heating controller) for changing the
control strategy (room-supply air temperature cascade control), configurable
2 / 36
Type summary
3 / 36
When ordering, please give name and type reference of the controller, e.g.:
Universal controller RLU236.
The products listed under "Accessories" must be ordered as separate items.
Equipment combinations
Product documentation
Technical design
With the help of the built-in operation or the OCI700.1 service tool, the controller
affords:
Activation of a programmed application (refer to "Programmed standard applica-
tions")
Modification of a programmed application
Free configuration of applications
Optimization of the controller settings
4 / 36
The universal controller consists of terminal base and controller insert with built-in
operation.
The terminal base can be fitted to a DIN mounting rail or is screwed directly on a
flat surface. It consists of a plastic housing with 2 terminal levels.
The controller insert engages in the terminal base. It consists of a plastic housing
which accommodates the printed circuit boards.
Controller operation is fully integrated.
3101Z06
connecting elements
1
2
3
4
9 8 7 6 5
Legend 1 OK button for confirming the selected menu line or the value entered
2 Navigation button, upward (+) for selecting the menu line or changing the value
3 Navigation button, downward (–) for selecting the menu line or changing the value
4 ESC button for returning to the previous menu or for rejecting the value entered
5 Connection facility for the service tool (RJ45 connector)
6 Display
7 Catch for fitting the controller to a top hat rail
8 Fixing facility for a cable tie (cable strain relief)
9 Rest for the terminal cover
Engineering notes
5 / 36
Commissioning notes
Disposal notes
The devices are considered electronics devices for disposal in terms of European
Directive 2012/19/EU and may not be disposed of as domestic garbage.
Dispose of the devices through channels provided for this purpose.
Comply with all local and currently applicable laws and regulations.
Warranty
Technical data on specific applications are valid only together with Siemens prod-
ucts listed under "Equipment combinations". Siemens rejects any and all warran-
ties in the event that third-party products are used.
6 / 36
7 / 36
Perm. cable lengths For passive measuring and positioning signals (measuring errors can be
Type of signal corrected)
LG-Ni 1000, T1 max. 300 m
Pt 1000 max. 300 m
0...1000 max. 300 m
1000...1235 max. 300 m
Contact sensing max. 300 m
For DC 0...10 V measuring and control signals refer to Data Sheet of the
signal delivering device
8 / 36
9 / 36
Internal diagrams
RLU202
3101G08
G X1 M X2 M G1 X3 M X4 M G1 D1 M Q11 Q23
RLU220
3101G09
G X1 M X2 M G1 X3 M X4 M G1 D1 M
G0 G1 Y1 G0 G1 Y2 G0
RLU222
3101G02
G X1 M X2 M G1 X3 M X4 M G1 D1 M Q11 Q23
RLU232
3101G03
G X1 M X2 M G1 X3 M X4 M G1 X5 M D1 M D2 M Q11 Q33
RLU236
3101G04
G X1 M X2 M G1 X3 M X4 M G1 X5 M D1 M D2 M Q11 Q23 Q33 Q41 Q53 Q63
Notes Each terminal (spring cage terminal) can only accommodate 1 solid wire or 1 stranded wire. Double
terminals are internally interconnected
If a 3-position AC 230 V actuator is used, the radio suppression element must be activated:
Connect terminal N1 to the neutral conductor and fit a wire link between N1 and N2 (see connection
diagram 5)
10 / 36
3101A01
(3) (1)
B M B1 B M B5 B2 M R5
AC 24 V
G X... M X... M X... M
G0 N1
G0
Connection diagram 2: Measuring section with active sensor and active signal
source
G
3101A02
(1) (2) (3) (4)
B M G B3 GL GN out in R2
AC 24 V
G X... M G1 G1 M X...
G0 N1
G0
3101A04
G (CO2/
(CO2) VOC) G (CO2 )
M U1 U2 B4 M U1
B4
AC 24 V
AC 24 V
G G1 M X... G G1 M X...
G0 G0 N1
N1
G0 G0
Connections on the
control and monitoring Connection diagram 5:
side
L
G
3101A 05_A
1 L M D1 Q11
S7
2 4 F3 N Q12 Q14 S5
G Y Y1 Y2
G0 N
Y3 Y
G0
H1 K1 K2
N
11 / 36
Note The plant diagrams / connection diagrams assigned to the basic types are only
examples.
S01
A01 Extract air (room) temperature control with electric air heater T
B2
battery. N. X1
Options:
Minimum and maximum limitation of the supply air tempera- T T T R5
ture B9 E1 B1
N.X4
N.Q1
Outside temperature-dependent functions N.X3
N.Q2
N. X2
S01
B5
A02 Supply air temperature control with electric air heater battery. T
N.X2
Cascade
Options:
Room temperature cascade control
Outside temperature-dependent functions T T T R5
Remote setpoint readjuster B9 E1 B1
N.X4
N.Q1
2-stage electric air heater battery N.X3
N.Q2
N.X1
S01
B5
A03 Supply air temperature control with hot water heating coil. T
N.X2
Cascade
Options:
Room temperature cascade control
Outside temperature-dependent functions T T T R5
Remote setpoint readjuster B9 B1
N.X4
Y3 M
N.Q1 S5
N.Q2
N.D1
S01
A04 Extract air (room) temperature control with DX cooler battery. T
Options: B2
N.X1
Minimum and maximum limitation of the supply air tempera-
ture T T T R5
Outside temperature-dependent functions B9 M7 B1
N.X4
N.X2
Remote setpoint readjuster N.X3 N.Q 1
N.Q 2
B5
T
A05 Supply air temperature control with DX cooler battery. N.X2
Cascade
Options:
Room temperature cascade control
Outside temperature-dependent functions T T T R5
Remote setpoint readjuster B9 M7 B1
N.X4
N.X1
2-stage DX cooler battery N.X3 N.Q 1
N.Q 2
A06 Extract air (room) temperature control with hot water heating T
12 / 36
S01
B5
A07 Supply air temperature control with hot water heating coil and T
N.X2
Options:
Room temperature cascade control T T T R5
N.X4
Outside temperature-dependent functions B9 B1
M3 M7
Remote setpoint readjuster N.X3
N.Q 1 N.Q 2
N.X1
S01
U01 Extract air (room) humidity control (r.h.) with spray humidifier.
Options: B12
N.X1
Maximum limitation of the air humidity [%]
N.X2
Comfort / Protection Mode changeover (time switch) [%]
M8
N.Q 1 S5
N.Q2 N.D1
S01
B5
U02 Extract air (room) humidity control (r.h.) with DX cooler battery. T
N.X3
Options: B12
N.X1
Additional maximum selection from internal and external [%]
signal R5
T
Room temperature-dependent shifting of humidity setpoint N.X4
M7
Remote setpoint adjuster N.Q1
N.Q2
2-stage DX cooler battery S5
N. X2
Comfort / Protection Mode changeover (time switch) N.D1
S01
B5
U03 Extract air (room) humidity control (a.h.) with DX cooler battery. T T
T
N.X3
Options: B18
Additional maximum selection from internal and external N.X1
[g/kg]
signal R5
T
Room temperature-dependent shifting of humidity setpoint M7
N.X4
S01
U04 Extract air (room) humidity control (r.h.) with spray humidifier
B12
and DX cooler battery. N.X1
Options: [%]
M7 N.X2
signal N.Q2 [%]
M8
Remote setpoint adjuster N.Q1 S5
N.D1 N. X3
Comfort / Protection Mode changeover (time switch)
RLU202 AZZ001 LU0 HQ
S01
B4
U05 Indoor air quality control with fan control. AQ
N.X1
[ppm]
Options:
Additional maximum selection from internal and external
signal T T R5
Outside temperature-dependent functions B9 M1
N.Q1
N.X4
N.X3
Remote setpoint adjuster N.Q2
2-speed fan S5
Comfort / Protection Mode changeover (time switch) N.D1 N .X2
T B7
N.X2
13 / 36
S01
U07 Boiler temperature control (substitute for RCA12.2)
Application:
Minimum limitation of the boiler return temperature Y3 S5
Options: N.Q1 N.D1
N.Q2 M
Remote setpoint adjuster (absolute)
Comfort / Protection Mode changeover (time switch) T R5
N.X2
T B7
N.X1
S01
U08 Universal control (substitute for RKN2 / RKN22) T
B2
Application: N.X1
S5
N.D1
S01
RLU202 ZZZ001 LU0 HQ DC 0 ... 10 V
A01
G X1 M G1 D1 M Q11 Q23
RLU202
G0 N1 Q12 Q14 N2 Q24
3P
A01
G X1 M G1 D1 M Q11 Q23
RLU202
G0 N1 Q12 Q14 N2 Q24
2Q VAR.
A01 Extract air (room) temperature control with hot water heating T
coil. B2
N.X1
Options:
Minimum and maximum limitation of the supply air tempera- T T T R5
ture B9 B1
N.X4
M
Outside temperature-dependent functions Y3 S5
Comfort / Protection Mode changeover (time switch) N.Y1 N.D1
B5
A02 Supply air temperature control with hot water heating coil. T
N.X2
Cascade
Options:
Room temperature cascade control
Remote setpoint readjuster T T T R5
Outside temperature-dependent functions B9 B1
N.X4
N.X3 N.X1
Comfort / Protection Mode changeover (time switch)
M
Y3 S5
N.Y1 N.D1
14 / 36
S01
A03 Extract air (room) temperature control with hot water heating T
M
Comfort / Protection Mode changeover (time switch) Y3 S5
N.Y1 N.D1
S01
B5
T
A04 Supply air temperature control with hot water heating coil and N.X2
Cascade
frost protection.
F3
Options: N.X3
Y3 S5
N.Y1 N.D1
S01
1
A05 Extract air (room) temperature control with hot water heating T
B2
coil, frost protection. N.X1
Options: F3
N.X3
M
Comfort / Protection Mode changeover (time switch) Y3 S5
N.Y1 N.D1
S01
A06 Extract air (room) temperature control with chilled water cooling T
B2
coil. N.X1
Options:
Minimum and maximum limitation of the supply air tempera- T T T R5
ture B9 B1
N.X4
N.X3 N.X2
Remote setpoint readjuster
M
Outside temperature-dependent functions Y4 S5
Comfort / Protection Mode changeover (time switch) N.Y1 N.D1
S01
B5
A07 Supply air temperature control with chilled water cooling coil. T
N.X2
Cascade
Options:
Room temperature cascade control
Remote setpoint readjuster T R5
T T
Outside temperature-dependent functions B9 B1
N.X4
M
Y4 S5
N.Y1 N.D1
A08 Extract air (room) temperature control with mixed air dampers M
T
Y2 B2
and outside temperature-dependent functions. M N.X1
Y1
Options: N.Y1 M
Y6
S5
N.D1 N.X2
A09 Supply air temperature control with heating / cooling coil and
frost protection.
Options: F3
N.X3
M
T F16
Y5 N.X2 S5
N.Y1 N.D1
15 / 36
S01
A10 Extract air (room) temperature control with hot water heating T
B2
coil and chilled water cooling coil. N.X1
Options:
Room temperature cascade control T T T R5
Outside temperature-dependent functions B9 B1
N.X4
M M
Comfort / Protection Mode changeover (time switch) Y3 Y4 S5
N.Y1 N.Y2 N.D1
S01
B5
A11 Supply air temperature control with hot water heating coil and T
N.X2
Cascade
chilled water cooling coil.
Options:
Room temperature cascade control T T T R5
N.X4
Outside temperature-dependent functions B9 B1
N.X1
Remote setpoint readjuster N.X3
M M
Comfort / Protection Mode changeover (time switch) Y3 Y4 S5
N.Y1 N.Y2 N.D1
S01
1
A12 Extract air (room) temperature control with hot water heating T
B2
coil, frost protection, chilled water cooling coil. N.X1
Options: F3
N.X3
Minimum and maximum limitation of the supply air tempera- T
1
T
T
ture B9 B1
N.X4 N.X2
Outside temperature-dependent functions
M M
Comfort / Protection Mode changeover (time switch) Y3 Y4 S5
N.Y1 N.Y2 N.D1
S01
B5
A13 Supply air temperature control with hot water heating coil, frost T
N.X2
Cascade
protection, chilled water cooling coil.
Options: F3
N.X3
Room temperature cascade control T T
T
Outside temperature-dependent functions B9 B1
Comfort / Protection Mode changeover (time switch) N.X4 N.X1
M M
Y3 Y4 S5
N.Y1 N.Y2 N.D1
S01
A14 Extract air (room) temperature control with closed-circuit heat T
B5
A15 Supply air temperature control with closed-circuit heat recovery T
N.X2
Cascade
system and hot water heating coil.
Options:
Room temperature cascade control
R5
Outside temperature-dependent functions T T
T
N.X4
B9 B1
Remote setpoint readjuster N.X3
Y11
N. Y2 N.X1
A16 Extract air (room) temperature control with mixed air dampers, M
T
Y2
hot water heating coil, frost protection. M
B2
N.X1
Options: Y1
N.Y2 M
Y6 F3
N.X3
M
Comfort / Protection Mode changeover (time switch) Y3 S5
N.Y1 N.D1
16 / 36
S01
1 B5
A17 Supply air temperature control with mixed air dampers, hot M
T
N.X2
Y2 Cascade
water heating coil, frost protection. M
Options: Y1
N.Y2 M
Y6 F3
N.X3
Y3 S5
N.Y1 N.D1
S01
A18 Extract air (room) temperature control with chilled water cooling T
B2
coil and 2 cooling towers. N.X1
Options:
Minimum and maximum limitation of the supply air tempera- T T T R5
N.X4
ture B9 f1
f2
G1 f1
f2
G2 B1
N.X3 N.Y1 N.Y2
Outside temperature-dependent functions N.X2
S01
U01 Extract air (room) humidity control (r.h.) with spray humidifier.
Options: B12
N. X1
Maximum limitation of the supply air humidity [%]
N.X2
Y8 [%]
N.Y1
S5
N.D1
S01
U02 Extract air (room) humidity control (r.h.) with chilled water
cooling coil. B12
N. X1
Options: [%]
S01
U03 Extract air (room) humidity control (a.h.) with chilled water T T
Options:
f1
T R5
Minimum and maximum limitation of the differential pressure f2
N.X3
Remote setpoint adjuster G1
N.Y1
Comfort / Protection Mode changeover (time switch)
S5
N.D1
Options: f1
f2
f1
f2
B9 S5
N.X3 N.D1
17 / 36
S01
Minimum and maximum limitation of the differential pressure R5
f1 T
Remote setpoint adjuster f2 N.X3
S5
N.D1
S5
S01
B4
U08 Indoor air quality control with mixed air dampers. M
AQ
N.X1
Y2 [ppm]
Options: M
Y1
Additional maximum selection from internal and external N.Y1 M
Y6
signal T R5
Remote setpoint adjuster N.X3
S5
S01
U10 Universal control (substitute for RKN8 / RKN88) T
Application: B2
N. X1
A01 Extract air (room) temperature control with electric air heater T
B2
battery. N. X1
Options:
Minimum and maximum limitation of the supply air tempera- T T T R5
N.X4
ture B9 E1 B1
N.X3 N.Q1
Outside temperature-dependent functions N.Q2
N.Y1
N. X2
B5
A02 Supply air temperature control with electric air heater battery. T
N.X2
Cascade
Options:
Room temperature cascade control
Outside temperature-dependent functions T T T R5
Remote setpoint readjuster B9 E1 B1
N.X4
N.Q1
2-stage electric air heater battery N.X3
N.Q2
N.Y1
N.X1
18 / 36
S01
B5
A03 Supply air temperature control with hot water heating coil. T
N.X2
Cascade
Options:
Room temperature cascade control
Outside temperature-dependent functions T T T R5
Remote setpoint readjuster B9 B1
N.X4
N.X1
Comfort / Protection Mode changeover (time switch) N.X3
Y3 M
N.Q1 S5
N.Q2
N.D1
S01
1
A04 Extract air (room) temperature control with hot water heating T
Y3 S5
N.Y1 N.D1
S01
1
A05 Extract air (room) temperature control with hot water heating T
M3
Remote setpoint readjuster N.Q2
N.X2
S01
1 B5
A06 Supply air temperature control with hot water heating coil, frost T
N.X2
Options: F3
N.X3
Room temperature cascade control 1
T T
Outside temperature-dependent functions B9
T
B1
M3
Comfort / Protection Mode changeover (time switch) N.X4
N.Q2
N.X1
Y3 S5
N.Y1 N.D1
A09 Extract air (room) temperature control with hot water heating T
B2
coil and chilled water cooling coil. N.X1
Options:
Room temperature cascade control T T T R5
Outside temperature-dependent functions B9 B1
N.X4
M3 M4
Remote setpoint readjuster N.X3
N.Q1 N.Q2
N.X2
M M
Comfort / Protection Mode changeover (time switch) Y3 Y4 S5
N.Y1 N.Y2 N.D1
19 / 36
S01
B5
A10 Supply air temperature control with hot water heating coil and T
N.X2
Cascade
chilled water cooling coil.
Options:
Room temperature cascade control T T T R5
Outside temperature-dependent functions B9 B1
N.X4
M3 M4 N.X1
Remote setpoint readjuster N.X3
N.Q 1 N.Q2
M M
Comfort / Protection Mode changeover (time switch) Y3 Y4 S5
N.Y1 N.Y2 N.D1
S01
A11 Extract air (room) temperature control with electric air heater T
B2
battery and chilled water cooling coil. N.X1
Options:
Minimum and maximum limitation of the supply air tempera- T R5
T T
ture B9 E1 B1
N.X4
N.Q1 N.X2
Outside temperature-dependent functions N.X3
N.Q2
N.Y1
M
Remote setpoint readjuster Y4 S5
2-stage electric air heater battery N.Y2 N.D1
S01
B5
A12 Supply air temperature control with electric air heater battery T
N.X2
Cascade
and chilled water cooling coil.
Options:
Room temperature cascade control T R5
T T
Outside temperature-dependent functions B9 E1 B1
N.X4
N.Q1 N.X1
Remote setpoint readjuster N.X3
N.Q2
N.Y1
M
2-stage electric air heater battery Y4 S5
Comfort / Protection Mode changeover (time switch) N.Y2 N.D1
A15 Extract air (room) temperature control with hot water heating 1
T
coil, frost protection, chilled water cooling coil and fan release. B2
N.X1
Options: F3
N.X3
Minimum and maximum limitation of the supply air tempera- 1
T T
ture B9
T
B1
Outside temperature-dependent functions N.X4 M3
N.Q2
N.X2
Y3 Y4 S5
N.Y1 N.Y2 N.D1
B5
A16 Supply air temperature control with hot water heating coil, frost 1
T
N.X2
Options: F3
N.X3
Room temperature cascade control 1
T T
Outside temperature-dependent functions B9
T
B1
Comfort / Protection Mode changeover (time switch) N.X4 M3
N.Q2
N.X1
M M
Y3 Y4 S5
N.Y1 N.Y2 N.D1
20 / 36
S01
A17 Extract air (room) temperature control with hot water heating 1
T
Y3 M7 S5
N.Y1 N.Q2 N.D1
S01
B5
A18 Supply air temperature control with hot water heating coil, frost 1
T
N.X2
Options: F3
N.X3
Room temperature cascade control 1
T T
Outside temperature-dependent functions B9
T
B1
Y7
Comfort / Protection Mode changeover (time switch) N.X4 N.Y2 N.X1
Y3 M7 S5
N.Y1 N.Q2 N.D1
S01
A19 Extract air (room) temperature control with closed-circuit heat T
M6
recovery system and hot water heating coil. N.Q2
B2
N.X1
Options: M
Y6
Minimum and maximum limitation of the supply air tempera- N.Y2
R5
ture T T T
N.X4
B1
Outside temperature-dependent functions B9
N.X3
M3 N.X2
N.Q1
Remote setpoint readjuster M
S01
B5
A20 Supply air temperature control with closed-circuit heat recovery T
N.X2
M6 Cascade
system and hot water heating coil. N.Q2
Options: M
Y6
Room temperature cascade control N.Y2
R5
Outside temperature-dependent functions T T T
N.X4
B1
Remote setpoint readjuster B9
N.X3
M3 N.X1
N. Q1
Comfort / Protection Mode changeover (time switch) M
Y3 S5
N.Y1 N.D1
S01
A21 Extract air (room) temperature control with mixed air dampers, 1
T
M
Y2
hot water heating coil, frost protection and fan release. M
B2
N.X1
Options: Y1 Y6 F3
N.Y2 M N.X3
Minimum and maximum limitation of the supply air tempera- 1
T T
ture B9
T
B1
Outside temperature-dependent functions N.X4 M3
N.Q 2
N.X2
Y3 S5
N.Y1 N.D1
B5
A22 Supply air temperature control with mixed air dampers, hot 1
T
N.X2
M
Y2
water heating coil, frost protection and fan release. Cascade
M
Options: Y1 Y6 F3
N.Y2 M N.X3
Room temperature cascade control 1
T T
Outside temperature-dependent functions T
B1
B9
Comfort / Protection Mode changeover (time switch) N.X4 M3
N.Q 2
N.X1
Y3 S5
N.Y1 N.D1
A23 Extract air (room) temperature control with chilled water cooling T
B2
coil and 2 cooling towers. N.X1
Options:
Minimum and maximum limitation of the supply air tempera- T N.Q1 N.Q2 T T R5
N.X4
ture B9 f1
f2
G1 f1
f2
G2 B1
N.Y1 N.Y2
Outside temperature-dependent functions N.X3 N.X2
21 / 36
S01
A24 Extract air (room) temperature control with mixed air dampers, M
T
Y2
hot water heating coil and DX cooler battery. M
B2
N.X1
Y1
Options: N.Y2 M
Y6
M
Remote setpoint readjuster Y3 S5
Comfort / Protection Mode changeover (time switch) N.Y1 N.D1
S01
B5
A25 Supply air temperature control with mixed air dampers, hot M
T
N.X2
Y2
water heating coil and DX cooler battery. M
Cascade
Options: Y1
N.Y2 M
Y6
M
Comfort / Protection Mode changeover (time switch) Y3 S5
N.Y1 N.D1
S01
A26 Extract air (room) temperature control with mixed air dampers, M
T
Y2
hot water heating coil and DX cooler battery. M
B2
N.X1
Options: Y1
N.Y2 M
Y6
M
Remote setpoint readjuster Y3 S5
2-stage DX cooler battery N.Y1 N.D1
S01
B5
A27 Supply air temperature control with mixed air dampers, hot M
T
N.X2
Y2
water heating coil and dx cooler battery. M
Cascade
Options: Y1
N.Y2 M
Y6
S01
A28 Extract air (room) temperature control with mixed air dampers, M
T
Y2
B2
electric air heater battery and chilled water cooling coil. M N.X1
Options: Y1
N.Y1 M
Y6
M
Remote setpoint readjuster Y4 S5
2-stage electric air heater battery N.Y2 N.D1
B5
A29 Supply air temperature control with mixed air dampers, electric M
T
N.X2
Y2 Cascade
air heater battery and chilled water cooling coil. M
Y1
Options: N.Y1 M
Y6
N.Q1
Remote setpoint readjuster N.X3
N.Q2
N.X1
M
2-stage electric air heater battery Y4 S5
Comfort / Protection Mode changeover (time switch) N.Y2 N.D1
U01 Extract air (room) humidity control (r.h.) with spray humidifier.
Options: B12
N.X1
N.X2
Comfort / Protection Mode changeover (time switch) N.Y1 [%]
M8
N.Q 1 S5
N.Q2 N.D1
22 / 36
S01
Options: f1
f2
f1
f2
B9 S5
N.X3 N.D1
S01
B5
U04 Extract air (room) humidity control (r.h.) with DX cooler battery. T
N.X3
B12
Options: N. X1
signal R5
T
Room temperature-dependent shifting of humidity setpoint N.X4
Y7
Remote setpoint adjuster N.Y1
S01
B5
U05 Extract air (room) humidity control (a.h.) with DX cooler battery. T T
T
N.X3
Options: B18
Additional maximum selection from internal and external N.X1
[g/kg]
signal R5
T
Room temperature-dependent shifting of humidity setpoint Y7
N .X4
S01
B4
U06 Indoor air quality control with mixed air dampers and fan con- M
AQ
N.X1
Y2 [ppm]
trol. M
Y1
Options: N.Y1 M
Y6
N.X3
Outside temperature-dependent functions N.Q2
U07 Extract air (room) humidity control (r.h.) with spray humidifier
B12
and DX cooler battery. N.X 1
Options: [%]
N.X2
signal N.Y1 N.Y2
[%]
M8
Remote setpoint adjuster N.Q1
M7 S5
N.D1 N.X3
Comfort / Protection Mode changeover (time switch) N.Q2
23 / 36
S5
N.Q1
A01
G X1 M G1 D1 M Q11 Q23
RLU222
G0 N1 Q12 Q14 N2 Q24
3P
A01
G X1 M G1 D1 M Q11 Q23
RLU222
G0 N1 Q12 Q14 N2 Q24
2Q VAR.
Application: B2
N.X1
Temperature control (on/off pump control)
Options:
T R5
Remote setpoint adjuster (absolute) N.X2
M3 M4
Comfort / Protection Mode changeover (time switch) N.Q1 N.Q2
S5
N.D1
B2
Application: N. X1
24 / 36
S01
RLU222 ABL001 LU2 HQ
U16 Supply air differential pressure control
Options:
Switching via external time switch F1
Differential pressure monitor p
p
G1 S5
N.Y1 B7 N.D1
N.X1
F1
Setpoint shift through volumetric supply air flow p
S5
N.D1
G1 p
N.Y2 B7
N.X1
N.X3
Y8 M
S5
N.Y2 B11
N.X2 N.D1
Y4 M M8
N.Y1 N.Q1
25 / 36
S01
A01 Extract air (room) temperature control with heat recovery, hot T
1
T
S01
1 B5
A02 Supply air temperature control with heat recovery, hot water T
T
N.X2
S01
B5
A03 Supply air temperature control with hot water heating coil, frost 1
T
N.X2
Options: F3
N.X3
Room temperature cascade control 1
T T
Outside temperature-dependent functions B9
T
B1
Comfort / Economy changeover N.X4 M3
N.Q 3
N.X1
S5
Comfort / Protection Mode changeover (time switch) M M
N.D1
Y3 Y4 S6
N.Y1 N.Y2 N.D2
S01
A04 Extract air (room) temperature control with closed-circuit heat T
T M6
recovery system, hot water heating coil and chilled water cool- B21 N.Q3
B2
N. X1
N.X4
ing coil. M
Y6
Options: N.Y2
R5
Minimum and maximum limitation of the supply air tempera- T T T
N.X5
B9 B1
ture N.X3
M3 N.X2
S5
N.Q1
Outside temperature-dependent functions M M
N.D1
S6
Anti-icing protection for heat recovery N.Y1
Y3 Y4
N.Y3
N.D2
Options: N.X4 M
Y6
Room temperature cascade control N.Y2
R5
Outside temperature-dependent functions T T T
N.X5
B9 B1
Anti-icing protection for heat recovery N.X3
M3 N.X1 S5
N.Q1
Remote setpoint readjuster M M
N.D1
S6
Comfort / Economy changeover N.Y1
Y3 Y4
N.Y3
N.D2
A06 Extract air (room) temperature control with heat recovery, hot T T
B10 B2
water heating coil and chilled water cooling coil. N.X4 N.X1
Options:
Minimum and maximum limitation of the supply air tempera- T T
R5
ture B9 B1
T
N.X5
N.X3 Y11 M3 M4
Outside temperature-dependent functions N.Y2 N.Q1 N.Q3
N.X2
S5
M M
Anti-icing protection for heat recovery Y3 Y4
N.D1
S6
Remote setpoint readjuster N.Y1 N.Y3 N.D2
26 / 36
S01
B5
A07 Supply air temperature control with heat recovery, hot water T T
N.X2
B10
heating coil and chilled water cooling coil. N.X4
Cascade
Options:
Room temperature cascade control T T
R5
Outside temperature-dependent functions B9 B1
T
N.X5
N.X3 Y11 M3 M4 N.X1
Anti-icing protection for heat recovery N.Y2 N.Q1 N.Q3
S5
M M
Remote setpoint readjuster Y3 Y4
N.D1
S6
Comfort / Economy changeover N.Y1 N.Y3 N.D2
S01
A08 Extract air (room) temperature control with heat recovery, hot T
1
T
water heating coil, frost protection, chilled water cooling coil B10 B2
N.X5 N.X1
and fan release. F3
N.X3
Options: 1
T T
Minimum and maximum limitation of the supply air tempera- B9
T
B1
ture N.X4 Y11
N.Y2
M3
N. Q3
N.X2
S5
Outside temperature-dependent functions M M
N.D1
Y3 Y4 S6
Anti-icing protection for heat recovery N.Y1 N. Y3 N.D2
S01
B5
A09 Supply air temperature control with heat recovery, hot water T
1
T
N.X2
heating coil, frost protection, chilled water cooling coil and fan B10 Cascade
N.X5
release. F3
N.X3
Options: 1
T T
Room temperature cascade control B9
T
B1
M3
Outside temperature-dependent functions N.X4 Y11
N.Y2 N.Q 3
N.X1
S5
Anti-icing protection for heat recovery M M
N.D1
Y3 Y4 S6
Comfort / Economy changeover N.Y1 N.Y3 N.D2
1S01
A10 Extract air (room) temperature control with hot water heating T
B2
coil and 2 chilled water cooling coils. N.X1
Options:
Minimum and maximum limitation of the supply air tempera- T T
R5
ture B9 M3 M4 B1
T
N.X4
N.X3
Outside temperature-dependent functions N. Q1 N.Q 3 N.X2
S5
M M M
Remote setpoint readjuster Y3 Y4 Y15
N.D1
S6
Comfort / Economy changeover N.Y1 N.Y2 N.Y3 N.D2
S01
B5
A11 Supply air temperature control with hot water heating coil and 2 T
N.X2
Cascade
chilled water cooling coils.
Options:
Room temperature cascade control T T
R5
Outside temperature-dependent functions B9 M3 M4 B1
T
N.X4
N.X1
Remote setpoint readjuster N.X3 N.Q1 N.Q3
S5
M M M
Comfort / Economy changeover Y3 Y4 Y15
N.D1
S6
Comfort / Protection Mode changeover (time switch) N.Y1 N.Y2 N. Y3 N.D2
A12 Supply air temperature control and room humidity control (r.h.) T T
B15 B5
with heat recovery, hot water heating coil and spray humidifier. N.X3 N.X2
Options: Cascade
27 / 36
S01
1
A13 Extract air (room) temperature control and dewpoint control T
S01
1
A14 Supply air temperature and extract air (room) humidity control T
(r.h.) with hot water heating coil, frost protection, spray humidi- B2
N.X1
fier, chilled water cooling coil and fan release. F3
N.X4
Options: 1
T T T
Maximum limitation of the supply air humidity B9
T
B27 B1
Outside temperature-dependent functions N.X5 N.X3 N.X2
S5
Comfort / Economy changeover M M M
N.D1
Y3 Y4 Y10 S6
Comfort / Protection Mode changeover (time switch) N.Y2 N.Y3 N.Y1 N.D2
S01
1
A15 Extract air (room) temperature control and dew point control T
signal
Comfort / Economy changeover
Comfort / Protection Mode changeover (time switch)
RLU232 AEFH01 LU3 HQ N.Q1
S01
A16 Supply air temperature and room humidity control (r.h.) with M
1
T T
Y2
mixed air dampers, hot water heating coil, frost protection, M
B15 B5
N.X4 N.X2
chilled water cooling coil, spray humidifier and fan release. Y1
N.Y2 M
Y6 F3 Cascade
N.X3
Options: 1
T T
Room temperature cascade control B9
T
B1
Outside temperature-dependent functions N.X5 N.X1
S5
Comfort / Economy changeover M M
N.Q3
M8 N.D1
Y3 Y4 S6
Comfort / Protection Mode changeover (time switch) N.Y1 N.Y3 N.D2
Options:
Minimum and maximum limitation of supply air temperature
Outside temperature-dependent functions Y1
M
B31 M
F4
M
S5
Comfort / Economy changeover Y3
M1
Y4
S6
N.Q1
B9 S5
2 independent remote setpoint adjusters N.X5
N.Y1 N.Y2
N.D1
U02 Supply and extract air volume control with fan control. p
f1
G2
Options: N.Q2
f2 B8
N.X3
N.Y2
2 independent remote setpoint adjusters
Outside temperature-dependent functions T p
Comfort / Protection Mode changeover (time switch) B9 G1
f1
f2 B7
N.X5 N.Q1 N.X1
N.Y1
T
R5.1 T
R5.2 S5
N.X4 N.X2 N.D1
28 / 36
A01
G X1 M G1 D1 M Q11 Q33
RLU232
G0 Q12 Q14 Q34
2Q LIN.
A01
G X1 M G1 D1 M Q11 Q33
RLU232
G0 Q12 Q14 Q34
Q1
2Q BIN.
Q2
Q1
A01
G X1 M G1 D1 M Q11 Q33
RLU232
G0 Q12 Q14 Q34
2Q VAR.
S01
A01 Extract air (room) temperature control with electric air heater T
B2
battery. N.X1
Options:
Min. and max. limitation of the supply air temperature T T T R5
Outside temperature-dependent functions B9 E1 N.Q4 B1
N.X4
N.Q1 N.Q5
Remote setpoint readjuster N.X3
N.Q2 N.Q6
N.X2
S5
N.Q3 N.Y1
6-stage electric air heater battery N.D1
S6
Comfort / Economy changeover N.D2
29 / 36
A07 Extract air (room) temperature control with hot water air heat-
ing coil, frost protection, DX cooler battery and fan release.
Options: F3
Y3 M7 S6
4-stage DX cooler battery N.Q3
N.Q4
Comfort / Economy changeover N.Q5
N.Q6
A08 Supply air temperature control with hot water heating coil, frost
protection, DX cooler battery and fan release.
Options: F3
Y3 M7 S6
Comfort / Economy changeover N.Q3
N.Q4
Comfort / Protection Mode changeover (time switch) N.Q5
N.Q6
B5
A09 Supply air temperature and supply air humidity control (r.h.) 1
T T
N.X2
B5
A10 Supply air temperature and supply air humidity control (r.h.) 1
T T
N.X2
B15
with closed-circuit heat recovery system, DX cooler battery, hot M6
N.Q 3 N.X4
Cascade
30 / 36
Options: S5
B31 E2 E1
S6
2-stage direct expansion cooler battery
Comfort / Economy changeover
Comfort / Protection Mode changeover (time switch)
RLU236 AEGD01 LU3 HQ
A13 Extract air (room) temperature and mixed air temperature M
Y2 B12
control and humidity control Y6 M
Options:
Minimum and maximum limitation of supply air temperature
Outside temperature-dependent functions M
Y1 B31 E2 E1
N.Q3 N.Q1 S5
2-stage electric air heater battery N.Q4 N.Q2
S6
S01
U01 Extract air (room) humidity control (r.h.) with spray humidifier.
B12
Options: N.X1
pump control.
S01
31 / 36
S01
B5
U04 Extract air (room) humidity control (r.h.) with DX cooler battery. T
N.X3
Options: B12
N.X1
Additional maximum selection from internal and external [ %]
signal R5
T
Room temperature-dependent shifting of humidity setpoint Y7
N.X4
S01
B5
U05 Extract air (room) humidity control (a.h.) with DX cooler battery. T T
T
N.X3
Options: B18
Additional maximum selection from internal and external N.X1
[g/kg]
signal R5
T
Room temperature-dependent shifting of humidity setpoint Y7
N.X4
S01
B4
U06 Indoor air quality control with mixed air dampers and fan con- M
AQ
N.X1
Y2 [ppm]
trol. M
Y1
Options: N.Y1 M
Y6
S01
U07 Extract air (room) humidity control (r.h.) with spray humidifier
B12
and DX cooler battery. N.X1
Options: [%]
N.X2
signal N.Y 1 N.Y2
[%]
S5
M8
Remote setpoint adjuster N.Q1 M7
N.D1
S6
N.Q2
2-stage spray humidifier N.Q3
N.Q4
N.D2
N.Q5
4-stage DX cooler battery N.Q6 N.X3
3Q LIN.
32 / 36
A01
G X1 M G1 Q11 Q23 Q33 Q41 Q53 Q63
RLU236
G0 Q12 Q14 Q24 Q34 Q42 Q44 Q54 Q64
4Q LIN.
A01
G X1 M G1 Q11 Q23 Q33 Q41 Q53 Q63
RLU236
G0 Q12 Q14 Q24 Q34 Q42 Q44 Q54 Q64
5Q LIN.
A01
G X1 M G1 Q11 Q23 Q33 Q41 Q53 Q63
RLU236
G0 Q12 Q14 Q24 Q34 Q42 Q44 Q54 Q64
6Q LIN.
A01
G X1 M G1 Q11 Q23 Q33 Q41 Q53 Q63
RLU236
G0 Q12 Q14 Q24 Q34 Q42 Q44 Q54 Q64
3Q VAR.
A01
G X1 M G1 Q11 Q23 Q33 Q41 Q53 Q63
RLU236
G0 Q12 Q14 Q24 Q34 Q42 Q44 Q54 Q64
4Q VAR.
5Q VAR.
33 / 36
A01
G X1 M G1 Q11 Q23 Q33 Q41 Q53 Q63
RLU236
G0 Q12 Q14 Q24 Q34 Q42 Q44 Q54 Q64
6Q VAR.
A01
G X1 M G1 Q11 Q23 Q33 Q41 Q53 Q63
RLU236
G0 Q12 Q14 Q24 Q34 Q42 Q44 Q54 Q64
3Q BIN.
Q1
Q2
Q1
Q1
Q3
Q2
Q1
A01
G X1 M G1 Q11 Q23 Q33 Q41 Q53 Q63
RLU236
G0 Q12 Q14 Q24 Q34 Q42 Q44 Q54 Q64
Q1
Q2
Q1
4Q BIN.
Q1
Q3
Q2
Q1
Q1
Q2
Q1
Q4
Q1
Q3
Q2
Q1
S5
34 / 36
2
ø5
ø 10,5
=
44,5
66,4
50
90
35
=
44
3
= =
3101M02
EN 60 715-TH 35-7.5 97
RLU232, RLU236
86 176
5 3
3
2
ø5
ø 10,5
=
44,5
66,4
50
90
35
=
44
3
= =
3101M01
EN 60 715-TH 35-7.5 153
35 / 36
Mounting frame for RLU202, RLU220 Mounting frame for RLU232 and RLU236:
and RLU222:
45
87
45
87
113 168
3101M11
3101M10
143 5,6 199
5,6
24
24
Panel cutout if controller shall be wired prior to Panel cutout if controller shall be wired after mounting:
mounting:
L3
3101M09
4,4
4,4
66,4
45
66,4
82
45
4,4 4,4
18,5
18 L1 L3
10,7
7,8
3101M08
L2 18 L1
L2
Type L1 L2 Type L1 L2 L3
RLU202, RLU220, 97 133 RLU202, RLU220, 97 133 107
RLU222 RLU222
RLU232, RLU236 153 189
RLU232, RLU236 153 189 163
Published by:
Siemens Switzerland Ltd.
Building Technologies Division
International Headquarters
Gubelstrasse 22
6301 Zug
Switzerland
Tel. +41 41-724 24 24 © Siemens Switzerland Ltd 2000
www.siemens.com/buildingtechnologies Delivery and technical specifications subject to change
36 / 36