Академический Документы
Профессиональный Документы
Культура Документы
Product Datasheet
Bently Nevada* Asset Condition Monitoring
Description
The 2300 Vibration Monitors provide cost-effective continuous
vibration monitoring and protection capabilities for less critical
and spared machinery. They are specifically designed to
continuously monitor and protect essential medium to low
criticality machinery in a wide range of industries including: oil &
gas, power generation, water treatment, pulp and paper,
manufacturing, mining, cement, and other industries.
The 2300 Vibration Monitors deliver vibration monitoring and
high vibration level alarming. They include two channels of
seismic or proximity measurement inputs from various
accelerometer, Velomitor and Proximitor types, a speed input
channel for time-synchronous measurements, and outputs for
relay contacts. The 2300/20 monitor features a configurable 4-
20 mA output which interfaces more points to a DCS. The
2300/25 monitor features System 1* connectivity for
Trendmaster SPA interface which enables users to leverage
existing DSM SPA infrastructure.
The 2300 Vibration Monitors are designed for use on a broad
range of machine trains or individual casings where the sensor
point count fits the monitor’s channel count and where
advanced signal processing is desired.
Document: 105M0340
Rev. P
Page 1 of 16
Monitor Key Features l Each channel has one measurement group and two
bandpass measurements.
2300/20 l LCD and LED for real time value and status display.
l Ethernet 10/100 Base-T communication for
l Two 4-20mA outputs with internal current loop configuration using Bently Nevada Monitor
power supply. Configuration software (included) with RSA
l Continuous monitoring and protection encryption.
l Two acceleration/velocity/proximity inputs with l Local contacts for positive engagement of channel
synchronized sampling for advanced diagnostics. bypass, configuration lockout, and reset.
l One dedicated speed channel supporting Proximity l Two relay outputs with programmable setpoints.
probes, Magnetic pickup and Proximity switch type l Three buffered transducer outputs (including
sensors. Keyphasor signal) providing short circuit and EMI
l Supports process variable on all three input protection. Buffered outputs for each signal are
channels. through BNC connectors.
l Key measurements (Acceleration pk, Acceleration l Modbus® over Ethernet.
rms, Acceleration pk/rms, Velocity pk, Velocity rms,
Displacement pp, Displacement rms, Speed) real-
time provided with alarm configuration.
l Each channel has one measurement group and two
bandpass measurements.
l LCD and LED for real time value and status display.
l Ethernet 10/100 Base-T communication for
configuration using Bently Nevada Monitor
Configuration software (Included) with RSA
encryption.
l Local contacts for positive engagement of channel
bypass, configuration lockout, and reset.
l Two relay outputs with programmable setpoints.
l Three buffered transducer outputs (including
Keyphasor* signal) providing short circuit and EMI
protection. Buffered outputs for each signal are
through BNC connectors.
l Modbus® over Ethernet.
2300/25
l Trendmaster SPA interface.
l Continuous monitoring and protection.
l Two Acceleration/Velocity/Proximity inputs with
synchronized sampling for advanced diagnostics.
l One dedicated speed channel supporting Proximity
probes, Magnetic pickup and Proixmity switch type
sensor.
l Support process variable on all three input channels.
l Key measurements (Acceleration pk, Acceleration
rms, Acceleration pk/rms, Velocity pk, Velocity rms,
Displacement pp, Displacement rms, Speed) real-
time provided with alarm configuration.
Document: 105M0340
Rev. P
Page 2 of 16
Specifications revolution and event ratios for speed inputs up to 20 kHz.
Threshold voltage
0.1VDC
resolution
INPUTS Proximity Transducer Interface
Supply Voltage -22.8 to –25.2 VDC
POWER INPUT
Maximum Rated
DC Input 18~36VDC, max 7.5W 15 mA
Current
CHANNEL TYPES Short Circuit Current 15.1 mA to 23.6 mA
ICP Accelerometers
Accuracy ±1% of full scale range
Configurable
0.2 Hz to 20 kHz Input Impedance 3-wire Voltage Mode, 10 kΩ
Bandpass filter:
Scale Factor range 5 to 1000 mV/g Rpm range 1 to 120,000
Supports Bently transducer or 2/3 wires custom Alternatively, COM can be connected to an earth ground
transducer for Accelerometers, Velomitor and Proximitor. separately through a terminal.
Speed/Keyphasor
Keyphasor transducers support multiple events per
Document: 105M0340
Rev. P
Page 3 of 16
OUTPUTS Accuracy: 1% over operating temperature range
Update rate: 100ms
Buffered Output
Configurable with default 2mA clamp current
Three buffered outputs are No output feedback determination
2 Vibration Outputs
available on the monitor
1 Speed Output CAUTION: Two 4-20 mA outputs will NOT work with
through BNC connectors
external powered loop.
Relay
May be normally energized SPA Output (2300/25)
or de-energized High AC: 8Vpp
Relays provide two dry-
Low AC: 1.6Vpp
contact outputs No output feedback Input signal range DC GAP: 0 to -20Vdc (max
determination measurable AC signal is
Relay circuit specification in Non-Hazardous area: 1Vpp).
Type Single pole, double throw High/Low AC: ±1% of Full-
Scale at 100Hz
Sealing Epoxy sealed Accuracy
DC GAP: ±0.5V (measurable
100,000 cycles @ 5 amps AC accuracy: ±20mV)
Contact life 250 VAC
Frequency response 10Hz to 3000Hz ±5%
200,000 @ 1 amp, 24 VDC LEDs
1000 MΩ minimum @ 500 Indicates when the monitor
Insulation resistance OK
VDC is operating properly.
Relay closed contact Indicates hardware fault that
1 Ω maximum
resistance Protection fault is impacting alarm
Relay open contact determination.
1 MΩ minimum
resistance Indicates the alarm/relays
Maximum switched contact User inhibit have been intentionally
250V AC /250V DC inhibited from operation.
voltage
Maximum breaking contact Indicates user initiated
6A @250VAC / 6A @24VDC Bypass
current bypass action.
Maximum switched power 1500VA AC / 150 Watts DC Indicates if relays have been
Relay status
activated.
Relay circuit specification in Hazardous area:
Indicates the Ethernet status
Maximum switched contact 6A @24VAC / 5A @30VAC / TX/RX and monitor communicating
voltage and current 5.8A @24VDC / 4A @30VDC with remote software.
4-20mA Output (2300/20) Indicates the speed channel
Two 4-20mA outputs with internal current loop power has valid speed signal input
supply SPEED/AUX channel status
OR operating correctly when
4 to 20mA output values are proportional to the full-scale AUX.
of the associated measurement.
Alert LED: engages if any
Software configuration may determine the varible of each channel is in alert state .
output.
Channel Alarm Status Danger LED: engages if any
Voltage compliance: 0 to +12Vdc range across load
channel is in danger state.
Load resistance: 0 to 600Ω
Resolution: 0.3662uA
Document: 105M0340
Rev. P
Page 4 of 16
LCD Display CSA/NRTL/C
Allows viewing machine speed, vibration measurements Class I, Division 2/Zone 2
value, setpoints, and configuration information. AEx nA nC [ic] IIC T4 Gc
Class I, Division 2, Groups A,B,C & D; T4
COMMUNICATIONS ATEX/IECEx
Ethernet, 10Base-T and 2300/20
100Base-TX. Conforms to
IEEE802.3 II 3G
RJ-45 for 10Base- Ex nA nC [ic] IIC T4 Gc
Ethernet
T/100Base-TX Ethernet T4@ -30°C < Ta < 65°C (-22°F < +149°F)
cabling 2300/25
Cable length: 100 meters
(328 ft.) maximum II 3G
ENVIRONMENTAL LIMITS Ex nA nC ic [ic] IIC T4 Gc
-30 °C to +65 °C T4@ -30°C <Ta <65°C (-22°F < +149°F)
Operating Temperature
(-22 °F to +149 °F) Intrinsic Safety Parameters
-40 °C to +85 °C Uo: 24V; Io: 46mA; Co: 200nF;
Storage Temperature Proximitor Transducer
(-40 °F to +185 °F) Lo: 1mH
Humidity Up to 95%, non-condensing Uo: 24V; Io: 3.3mA; Co:
Accelerometer Transducer
Vibration Limitation 3g 200nF; Lo: 1mH
Document: 105M0340
Rev. P
Page 5 of 16
(Excluding Keyphasor sensor and 24 VDC power
Ordering Information supply 1)
002 1 Sensor and 1 Housing
Document: 105M0340
Rev. P
Page 6 of 16
(Excluding Keyphasor sensor and 24VDC power 003 2 Sensors
supply1)
1 - 2300/25 Monitor
006 2 Velomitors
1 - 6 ft. (1.8 m) shielded Ethernet cable
1 - 2300/20 Monitor
2 - Accelerometer sensors (200350)
1 - 6 ft. (1.8 m) shielded Ethernet cable
2 - 12 ft. (3.6m) cables (9571)
2 - Velomitor sensors (330500)
(Excluding Keyphasor sensor and 24VDC power
2 - 12 ft. (3.6 m) cable (9571) supply1)
(Excluding Keyphasor sensor and 24VDC power 004 2 Velomitors and 1 Housing
supply1)
1 - 2300/25 Monitor
BB: Approvals Option
1 - 6 ft. (1.8 m) shielded Ethernet cable
00 None 1 - Housing Kit: 105M6193-01 (fiberglass
02 Multiple Explosive Atmosphere Certifications housing for nonhazardous area) or
(ATEX/IECEx/CSA 105M6193-02 (stainless steel housing for
hazardous area) 12 x 14 in.
2300/25_KIT-AAA-BB: Bently Nevada 2300/25 2 - Velomitor sensors (330500)
Condition Monitoring System Kit 2 - 17 ft. (5.2 m) cable (9571)
AAA: Configuration (Excluding Keyphasor sensor and 24VDC power
supply1)
001 2 Sensors and 1 Housing
005 1 Velomitor and 1 Housing
1 - 2300/25 Monitor
1 - 2300/25 Monitor
1 - 6 ft. (1.8 m) shielded Ethernet cable
1 - 6 ft. (1.8 m) shielded Ethernet cable
1 - Housing Kit: 105M6193-01 (fiberglass
housing for nonhazardous area) or 1 - Housing Kit: 105M6193-01 (fiberglass
105M6193-02 (stainless steel housing for housing for nonhazardous area) or
hazardous area) 12 x 14 in. 105M6193-02 (stainless steel housing for
hazardous area) 12 x 14 in.
2 - Accelerometer sensors (200350)
1 - Velomitor sensor (330500)
2 - 17 ft. (5.2 m) cables (9571)
1 - 17 ft. (5.2 m) cable (9571)
(Excluding Keyphasor sensor and 24 VDC power
supply 1) (Excluding Keyphasor sensor and 24VDC power
supply1)
002 1 Sensor and 1 Housing
006 2 Velomitors
1 - 2300/25 Monitor
1 - 2300/25 Monitor
1 - 6 ft. (1.8 m) shielded Ethernet cable
1 - 6 ft. (1.8 m) shielded Ethernet cable
1 - Housing Kit: 105M6193-01 (fiberglass
housing for nonhazardous area) or 2 - Velomitor sensors (330500)
105M6193-02 (stainless steel housing for 2 - 12 ft. (3.6 m) cable (9571)
hazardous area) 12 x 14 in.
(Excluding Keyphasor sensor and 24VDC power
1 - Accelerometer sensor (200350) supply1)
1 - 17 ft. (5.2 m) cable (9571)
(Excluding Keyphasor sensor and 24VDC power
supply1)
Document: 105M0340
Rev. P
Page 7 of 16
BB: Approvals Option 105M6193-02 Stainless Steel Housing for 2300
KIT (can be used in hazardous
00 None
area)
02 Multiple Explosive Atmosphere Certifications 105M6193-01 Fiberglass NEMA 4X/IP66
(ATEX/IECEx/CSA
weatherproof housing with
window in door (includes mounting
System 1:
plate for monitor)
2300/20 can interface to System 1 V16.2 or higher Dimensions:
for expanded condition monitoring and analysis. Width: 338.3 mm (13.3 in)
Height: 389.1 mm (15.3 in)
System 1 software and the 2300 device
Depth: 209.8 mm (8.2 in)
connectivity (P/N 3071/13) are sold separately.
Refer to document 108M5214 for System 1 (used in nonhazardous area)
detailed information.
3071/13-AA-BB: System 1 2300 Series Device
Import
AA: Not available for 2300 monitor
00
Document: 105M0340
Rev. P
Page 8 of 16
200350 Accelerometer Sensor
Document: 105M0340
Rev. P
Page 9 of 16
330525 Velomitor
330500 Velomitor
190501 Velomitor
330505 Velomitor
Document: 105M0340
Rev. P
Page 10 of 16
AA: From “03” to “99” Increments of 1.0 foot
AAA:
Document: 105M0340
Rev. P
Page 11 of 16
AA : Accessories
16 16 ft. (4.8 m) Bulk Cable from Proximity
02120015
32 32 ft. (9.8 m) sensor to monitor (500 ft.)
64 64 ft. (19.5 m) Low cost cable for 2-wire
9571-AA*
286244 Magnetic mounting base ¼- transducer
28 threaded hole
Software
Ethernet Cables
100M9465-01 BN Monitor Configuration
138131-AAA Standard 10 Base-T/100 Base-TX SW/FW DVD
Shielded Category 5 Cable with RJ-45 -BNMC version 5.2 or greater
connectors (solid conductor) -2300 series monitor
firmware
(DVD includes 2300 Series
AAA: Cable Length Software Guide)
Document: 105M0340
Rev. P
Page 12 of 16
Graphs and Figures
Document: 105M0340
Rev. P
Page 13 of 16
Wiring Diagram
Note: 2300/20 and 2300/25 use the same interface connector for recorder output or SPA output.
Document: 105M0340
Rev. P
Page 14 of 16
2300/25 Wiring Diagram
Note: 2300/20 and 2300/25 use the same interface connector for recorder output or SPA
output.
Document: 105M0340
Rev. P
Page 15 of 16
© 2014-2017 Bently Nevada, LLC. All rights reserved.
* Denotes a trademark of Bently Nevada, LLC, a wholly owned subsidiary of General Electric Company.
All product and company names are trademarks of their respective holders.
Use of the trademarks does not imply any affiliation with or endorsement by the respective holders.
The information contained in this document is subject to change without prior notice.
Printed in USA. Uncontrolled when transmitted electronically.
1631 Bently Parkway South, Minden, Nevada USA 89423
Phone: 1-775.782.3611 www.GEmeasurement.com
Document: 105M0340
Rev. P
Page 16 of 16