Академический Документы
Профессиональный Документы
Культура Документы
CLICK HERE
Home Electronic Project Kits Store Jobs Advertise With Us Write For Us | Earn Money
Audio oscillator circuit SORT BY TYPE
101-Announcements (28)
admin February 22, 2012 13 Comments
555 Timer IC (16)
8051 (26)
source is on all the time and second current is switched ON and OFF using a ip- op. Battery Circuits (23)
Suppose the second current source is OFF and the rst current source is ON, then the C plus plus (7)
capacitor C2 will be charged with a continuous current (i) and the voltage across C2
C Programming (14)
increases linearly with time. When the voltage reaches 2/3 supply voltage, controlling ip
Cable TV Circuits (1)
op is triggered and the rst current source is activated. This current source carries
double the current (2i) making the capacitor C2 is discharged with a current i and the Camera Technology (5)
voltage across it drops linearly with time. When this voltage reaches 1/3 supply voltage, Clipping and Clamping Circuits (7)
the ip op is resetted to the initial condition and the cycle is repeated again. Clocking & Timer Circuits (2)
Drones (1)
Events (3)
Guides (15)
the external timing capacitor and R5 is a pull up resistor. Infographics (1)
Instruments (13)
(20)
Notes. Integrated Circuits
Inverters (5)
The circuit can be assembled on a vero board. Lab Manuals (20)
Use +10 /-10V DC dual supply for powering the circuit. (3)
LED related
The power supply must be well regulated and ltered.
Light Related (14)
All xed resistors are rated ¼ W.
Lighting Circuits (44)
MATLAB (3)
Microcontrollers (12)
Oscillators (25)
PCB (2)
Previous post Next post
Peripheral Interface Controller (PIC) (29)
Raspberry Pi (3)
Relays (3)
Robotics (7)
8 function christmas lamp
RTOS (2)
Audio ampli er circuit using TDA2040
Security & Saftey (17)
Interfacing gyroscope to arduino Sensor Circuits (16)
1 I assume the supply is +10v-0v–10v, where then is the 0v connected? Timer Circuits (3)
2 what forms the output of the circuit, I see the +ve sides are formed Tone generator circuits (20)
from the outputs of the IC on either pins2,3 & 9 of IC1, what forms the - Tools and Softwares (6)
ve output?
Transmitters (7)
3 I appears that pin 9 of IC1 is connected via a 15K resistor to the +10v
Tutorials (163)
line, are there similar connections to pins 2 & 3?
UPS (2)
VLSI (36)
Sultan Voltage Regulators (15)
December 5, 2014
Advertise With Us
where this IC ICL8038 is available. can i get it through online purchase.it
Authors
is not available in electronic component shops.
Datasheets
Disclaimer
Electronic Circuit Symbols
Microcontroller lab
Microprocessor Lab
I am sorry but i think it lacks of ground point or i am wrong?
Privacy Policy
Write For Us
Seetharaman
December 5, 2013
PCBFOX
Either is grnd or negative either one only. If single supply PCB Manufacturers
connect 20 volt to pin6 and 0 (gnd) to pin 11. Any
instrumentation dealer in bangalore hyderabad bombay or
chennai can supply as it is a intersil’s function generator chip..
Themisive
May 29, 2013
To terence m. maloney
I think if you look at the specs for the chip, you’ll nd it requires a supply
of 15 v, NOT +10v as shown, the -10v should be 0v.
Brendy
April 9, 2018
Isiguzo C. E.
November 17, 2012
Sam.
August 20, 2012
Pls sir, can the audio oscillator circuit be futher ampli ed with mosfet
also can 12volt dc be used to power the circuit instead of 10v. Dc.
terence m. maloney
March 28, 2012
hope that this will work as it should do to save me the expence of buying
a function generator.Where does the 0v of the power supply gets
connected?
Seetharaman
February 23, 2012
Hi HB 1volt RMS @ 5mA is the maximum output possible into 200 ohms
load.
Hi Mani Use modulation transformer or modulation transistor to do the
job.
V.MANI
February 22, 2012
How am I mix the radio frequency with this Sir? for IFT, Osc.,and Ant coil
tunning
HB
February 22, 2012
how much would be the output voltage and current on the waveform?
thank you
LEAVE A REPLY
Your email address will not be published. Required elds are marked *
Comment
Name *
Email *
Website
POST COMMENT
© 2018 CircuitsToday. About | Privacy Policy | Write For Us|Earn Money Latest Electronic Circuits
All rights reserved.