Академический Документы
Профессиональный Документы
Культура Документы
Ordering Information
All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission. 1
PixArt Imaging Inc.
E-mail: fae_service@pixart.com.tw V3.0, Apr. 2008
PixArt Imaging Inc.
1. Pin Configuration
1.1 Pin Description
LB RB
8
1
7
2 +Y 8
1
6 7
3 2
6
5 3
4 5
4
+X
All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission. 2
PixArt Imaging Inc.
E-mail: fae_service@pixart.com.tw V3.0, Apr. 2008
PixArt Imaging Inc.
CONTROL
OSCILLATOR OSC_RES
REGISTER
The PAW3204DB is a high performance, low power and low cost CMOS-process optical mouse sensor with
DSP integration chip that serves as a non-mechanical motion estimation engine for implementing a wireless
computer mouse. It is based on new optical navigation technology, which measures changes in position by
optically acquiring sequential surface images (frames) and mathematically determining the direction and
magnitude of movement. The mouse sensor is in an 8-pin optical package. The current X and Y information are
available in registers accessed via a serial port. The word "mouse sensor," instead of PAW3204DB, is used in the
document.
All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission. 3
PixArt Imaging Inc.
E-mail: fae_service@pixart.com.tw V3.0, Apr. 2008
PixArt Imaging Inc.
3.1 Registers
Address Name R/W Default Data Type
0x00 Product_ID1 R 0x30 Eight bits[11:4] number with the product identifier
Four bits[3:0] number with the product identifier
0x01 Product_ID2 R 0x5X
Reserved[3:0] number is reserved for future use
0x02 Motion_Status R - Bit field
0x03 Delta_X R - Eight bits 2’s complement number
0x04 Delta_Y R - Eight bits 2’s complement number
0x05 Operation_Mode R/W 0xB8 Bit field
0x06 Configuration R/W 0x04 Bit field
0x07 Image_Quality R - Eight bits unsigned integer
0x08 Operation_State R - Bit field
0x09 Write_Protect R/W 0x00 Bit field
0x0A Sleep1_Setting R/W 0x72 Bit field
0x0B Enter_Time R/W 0x12 Bit field
0x0C Sleep2_Setting R/W 0x92 Bit field
Image_
0x0D R/W 0x0A Eight bits unsigned integer
Threshold
Image_
0x0E R/W 0xE5 Bit field
Recognition
All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission. 4
PixArt Imaging Inc.
E-mail: fae_service@pixart.com.tw V3.0, Apr. 2008
PixArt Imaging Inc.
0x01 Product_ID2
Bit 7 6 5 4 3 2 1 0
Field PID[3:0] Reserved[3:0]
The value in this register can’t change. PID[3:0] can be used to verify that the serial communications
Usage link is OK. Reserved[3:0] is a value between 0x0 and 0xF, it can’t be used to verify that the serial
communications.
0x02 Motion_Status
Bit 7 6 5 4 3 2 1 0
Field Motion Reserved[1:0] DYOVF DXOVF RES[2:0]
Usage Motion_Status register allows the user to determine if motion has occurred since the last time it was
read. If so, then the user should read Delta_X and Delta_Y registers to get the accumulated motion. It
also tells if the motion buffers have overflowed since the last reading. The current resolution is also
shown.
Reading this register freezes the Delta_X and Delta_Y register values. Read this register before
reading the Delta_X and Delta_Y registers. If Delta_X and Delta_Y are not read before the motion
register is read a second time, the data in Delta_X and Delta_Y will be lost.
All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission. 5
PixArt Imaging Inc.
E-mail: fae_service@pixart.com.tw V3.0, Apr. 2008
PixArt Imaging Inc.
0x03 Delta_X
Bit 7 6 5 4 3 2 1 0
Field X7 X6 X5 X4 X3 X2 X1 X0
Usage X movement is counted since last report. Absolute value is determined by resolution. Reading clears
the register. Report range –128 ~ +127.
0x04 Delta_Y
Bit 7 6 5 4 3 2 1 0
Field Y7 Y6 Y5 Y4 Y3 Y2 Y1 Y0
Usage Y movement is counted since last report. Absolute value is determined by resolution. Reading clears
the register. Report range –128 ~ +127.
All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission. 6
PixArt Imaging Inc.
E-mail: fae_service@pixart.com.tw V3.0, Apr. 2008
PixArt Imaging Inc.
0x05 Operation_Mode
Bit 7 6 5 4 3 2 1 0
Field LEDsht_enh 0 1 Slp_enh Slp2_enh Slp2mu Slp1mu Wakeup
Usage Operation_Mode register allows the user to change the operation of the mouse sensor. Shown below
are the bits, their default values, and optional values.
Operation_Mode[4:0]
“0xxxx” = Disable sleep mode
“10xxx” = Enable sleep mode1
“11xxx” = Enable sleep mode2
“11100” = Force enter sleep23
“1x010” = Force enter sleep13 (If Slp2_enh is set, the mouse sensor still enter the sleep2
automatically.)
“1x001” = Force wakeup from sleep mode3
Notes:
1. Enable sleep mode, but disable automatic entering sleep2 mode, that is, only 2 modes will be used,
normal mode and sleep1 mode. After 256 ms (±20%) not moving during normal mode, the mouse
sensor will enter sleep1 mode, and keep on sleep1 mode until moving is detected or wakeup is
asserted. Note that the entering time depends on the setting of Enter_Time register.
2. Enable sleep mode full function, which is 3 modes will be used, normal mode, sleep1 mode and
sleep2 mode. After 256 ms (±20%) not moving during normal mode, the mouse sensor will enter
sleep1 mode, and keep on sleep1 mode until moving is detected or wakeup is asserted.
And after 61 sec (±20%) not moving during sleep1 mode, the mouse sensor will enter sleep2 mode,
and keep on sleep2 mode until detect moving or force wakeup to normal mode. Note that the
entering time depends on the setting of Enter_Time register.
3. Only one of these three bits slp2mu_enh, slp1mu_enh, and wakeup can be set to 1 at the same time,
others have to be set to 0. After a period of time, the bit, which was set to 1, will be reset to 0 by
internal signal.
4. The user can clear Slp_enh/Slp2_enh bit to make the mouse sensor enter normal mode. If the user
clears Slp_enh/Slp2_enh bit during normal mode, the mouse sensor will keep its status. If the user
clears Slp_enh/Slp2_enh bit during sleep mode, the mouse sensor will enter normal mode after it
detect any movement or the user sets Wakeup bit.
Notes
Field Name Description
Slp2mu Manual enter sleep2 mode, set “1” will enter sleep2 and this bit will be reset to “0”
Slp1mu Manual enter sleep1 mode, set “1” will enter sleep1 and this bit will be reset to “0”
Manual wake up from sleep mode, set “1” will enter wakeup and this bit will be
Wakeup
reset to “0”
0x06 Configuration
Bit 7 6 5 4 3 2 1 0
Field Reset MotSwk 0 0 PD_enh CPI [2:0]
Usage The Configuration register allows the user to change the configuration of the sensor. Shown below are
the bits, their default values, and optional values.
If MotSwk bit is clear, the MOTSWK pin is level-sensitive. The pin level remains low when motion
has occurred; in other words, Delta_X and Delta_Y registers has data. The mouse controller can read
Motion_Status register, Delta_X register, then Delta_Y register sequentially. After the mouse
controller reads all data, Delta_X and Delta_Y are both zero, the pin level will be high (see Section 7).
If MotSwk bit is set, the MOTSWK pin is edge-sensitive. The pin will send a pulse and trigger the
mouse controller when motion has occurred during the sleep mode. The mouse controller can read
Motion_Status register, Delta_X register, then Delta_Y register sequentially (see Section 7).
All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission. 8
PixArt Imaging Inc.
E-mail: fae_service@pixart.com.tw V3.0, Apr. 2008
PixArt Imaging Inc.
0x07 Image_Quality
Bit 7 6 5 4 3 2 1 0
Field Imgqa[7:0]
Image Quality is a quality level of the sensor in the current frame. Report range 0 ~ 255. The default
Usage
minimum level for normally working is 10. (please see Image_ Threshold register)
Notes Field Name Description
0x08 Operation_State
Bit 7 6 5 4 3 2 1 0
Field Reserved[3:0] Slp_state Op_state[2:0]
Usage Operation_State register allows the user to read the operation state of the sensor.
Notes Field Name Description
0x09 Write_Protect
Bit 7 6 5 4 3 2 1 0
Field WP[7:0]
Usage Write protect for the register 0x0A ~ 0x7F.
All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission. 9
PixArt Imaging Inc.
E-mail: fae_service@pixart.com.tw V3.0, Apr. 2008
PixArt Imaging Inc.
0x0A Sleep1_Setting
Bit 7 6 5 4 3 2 1 0
Field Slp1_freq[3:0] 0 0 1 0
Usage Sleep1_Setting register allows the user to set frequency time for the sleep1 mode.
0x0B Enter_Time
Bit 7 6 5 4 3 2 1 0
Field Slp1_etm[3:0] Slp2_etm[3:0]
Usage Enter_Time register allows the user to set enter time for the sleep1 and sleep2 mode.
0x0C Sleep2_Setting
Bit 7 6 5 4 3 2 1 0
Field Slp2_freq[3:0] 0 0 1 0
Usage Sleep2_Setting register allows the user to set frequency time for the sleep2 mode.
All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission. 10
PixArt Imaging Inc.
E-mail: fae_service@pixart.com.tw V3.0, Apr. 2008
PixArt Imaging Inc.
Image threshold: 0 (High recognition rate) ~ 255 (Low recognition rate). The
Imgqa_th[7:0]
minimum level for normally working is 10. Default is 00001010.
0x0E Image_Recognition
Bit 7 6 5 4 3 2 1 0
Field pk_wt[2:0] 0 Imgqa_df[3:0]
All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission. 11
PixArt Imaging Inc.
E-mail: fae_service@pixart.com.tw V3.0, Apr. 2008
PixArt Imaging Inc.
4. Specifications
4.1 Absolute Maximum Ratings
Stresses above those listed under "Absolute Maximum Rating" may cause permanent damage to the device.
These are stress ratings only. Functional operation of this device at these or any other conditions above those
indicated in the operational sections of this specification is not implied and exposure to absolute maximum
rating conditions for extended periods may affect device reliability.
All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission. 12
PixArt Imaging Inc.
E-mail: fae_service@pixart.com.tw V3.0, Apr. 2008
PixArt Imaging Inc.
All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission. 13
PixArt Imaging Inc.
E-mail: fae_service@pixart.com.tw V3.0, Apr. 2008
PixArt Imaging Inc.
All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission. 14
PixArt Imaging Inc.
E-mail: fae_service@pixart.com.tw V3.0, Apr. 2008
PixArt Imaging Inc.
Package Lid
Lens
OBJECT SURFACE
+X
+Y
CLIP
PLASTIC SPRING
LED
SURFACE IS 0 REF.
Unit: mm
Figure 5. 2D Assembly
All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission. 15
PixArt Imaging Inc.
E-mail: fae_service@pixart.com.tw V3.0, Apr. 2008
PixArt Imaging Inc.
All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission. 16
PixArt Imaging Inc.
E-mail: fae_service@pixart.com.tw V3.0, Apr. 2008
PixArt Imaging Inc.
6. Serial Interface
The synchronous serial port is used to set and read parameters in the mouse sensor.
SCLK: The serial clock line. It is always generated by the mouse controller.
SDIO: The serial data line is used to write and read data.
R /W
A D D R E S S ( 7 B IT ) D A T A ( 8 B IT )
( 1 B IT )
SCLK 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
DON'T DON'T
SDIO CARE 1 A6 A5 A4 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0 CARE
All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission. 17
PixArt Imaging Inc.
E-mail: fae_service@pixart.com.tw V3.0, Apr. 2008
PixArt Imaging Inc.
SCLK 7 8 9
S D IO A1 A0 H i-Z D7
tH O L D
3u s,m in
SCLK 16 1
H i-Z _
S D IO D0 R /W b it of n ex t ad dress
S D IO driven b y the m ou se co ntroller
SCLK 1 2 3 4 5 6 7 8 9
1
0
1
1
1
2
1
3
1
4
1
5
1
6
tR E S Y N C
1 u s , m in H i-Z _
S D IO A D D R E S S (R /W ) DATA
Note that this function is disabled when the mouse sensor is in the power down mode. If the user uses this
function during the power down mode, it will get out of synchronization. The mouse sensor and the mouse
controller also might get out of synchronization due to following conditions.
All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission. 18
PixArt Imaging Inc.
E-mail: fae_service@pixart.com.tw V3.0, Apr. 2008
PixArt Imaging Inc.
z Power On Problem - The problem occurs if the mouse sensor powers up before the mouse controller
sets the SCLK and SDIO lines to be output. The mouse sensor and the mouse controller might get out
of synchronization due to power on problem. An easy way to solve this is to use “watchdog timer
timeout”.
z ESD Events - The mouse sensor and the mouse controller might get out of synchronization due to ESD
events. An easy way to solve this is to use “watchdog timer timeout”.
1 1 1 1 1 1 1
SCLK 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6
SDIO
IDD
tPDR
All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission. 19
PixArt Imaging Inc.
E-mail: fae_service@pixart.com.tw V3.0, Apr. 2008
PixArt Imaging Inc.
7. MOTSWK function
7.1 Motion function
To use Motion function, the MotSwk bit in the Configuration register must be set to zero. Motion is used to
monitor if the mouse sensor has finished sending X-Y movement data to the mouse controller. If all movement
data are not read, MOTSWK pin level will remain low. After the mouse controller reads all movement data from
the mouse sensor, the mouse sensor will set MOTSWK pin level to high.
Note “A” Note “A”
Motion
Note “B”
SWKINT
tSWKINT
All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission. 20
PixArt Imaging Inc.
E-mail: fae_service@pixart.com.tw V3.0, Apr. 2008
PixArt Imaging Inc.
U1 ENCODER
SW1 RKEY
C1 SW VOUT C2
GND
U3
VCC_2.7V 1 28
PB5 PB6
EPSD 2 27
PB4 PB7
3 26
PA3 PA4
1
C18 MKEY 4 25
PA2 PA5 C3 15PF
U2 0.1uF
1 8 RKEY 5 24
2
SCLK 4 5
D2 LED R1
SCLK LED LED_2.7V
PAW3204DB
#4. RF TX Circuit
nRF24L01 notes
*X2 for +/-60ppm, CL = 12pF
*C16 and C17 must have values that match the
1
C10 C11
10nF 1nF U5
20
19
18
17
16
2
VSS
VSS
IREF
DVDD
VDD
(Reference only)
CE 1 15
Antenna
CE VDD L2 C12
CS 2
CSN VSS
14
SCK 3
SCK nRF24L01 ANT2
13 1 2 1 2
1
MOSI 4
MOSI ANT1
12 3.9nH
1
MISO 5
MISO VDD_PA
11 L3 1.5pF
C13
8.2nH 1pF
VDD
VSS
XC2
XC1
IRQ
L4
2
1 2
2.7nH
2
10
6
7
8
9
IRQ
1
R9
X2*
C17* 1M
16MHz
2 1
1
All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission. 21
PixArt Imaging Inc.
E-mail: fae_service@pixart.com.tw V3.0, Apr. 2008
PixArt Imaging Inc.
VCC
U1
1 8
2 A0 VCC 7
A1 WP
1
1
3
A2 SCL
6 SCK C2
4
GND SDA
5 EPSD C1 R1
0.1uF 2 1 22K
EEPROM VCC_3.3V
2
33nF
2
1
1
U2
C3 C4
VIN PAD 10nF 1nF U3
20
19
18
17
16
2
2
VOUT
AIC1734-33
GND
VSS
VSS
DVDD
VDD
IREF
VIN
(Reference only)
CE 1
CE VDD
15
C5
CS 2 14 L1
1
1
VCC VCC_3.3V MOSI 4 12 3.9nh
MOSI ANT1
1
MISO 5
MISO VDD_PA
11 L2 1.5pF
1
C7 C6
1
C8 8.2nH 1pF
VDD
VSS
XC2
XC1
IRQ
1uF L3
2
1uF 1 2
2
VCC 2.7nH
2
2
10
6
7
8
9
JP1 IRQ
1
R2 12
1 C9 C10
2
R3 12 D- 2.2nF 4.7pF
D+
2
R4 12
3 C11 + C12 Y 1*
C13 C14
4 22PF 22PF 1uF 10uF S1
1 2 16MHz
HEADER 4
C17 5PF 1 R5 2
1M
1
R6 4.7K
C15* C16*
U4 2 Y3
R7 4.7K CE 1 20 IRQ
2
PA3 PA4
CS 2
PA2 PA5
19 MISO 4 12MHz
VCC 3
PA1 PA6/TMR0
18 MOSI
C18 0.1uF 4
PA0 PA7/TMR1
17 IDSYNC
5 16
PC0 OSC1
C19 1UF ALED 6 15 C20 5PF D1 LED
3
PD4 OSC2
7
VDD RES
14 R8 10K ALED R9 270 1 2
R10 1.5K 8 13
D+ V33O VSS
9
USBD+/CLK PB7
12 EPSD C21 1UF
D- 10 11 SCK
USBD-/DATA PB6 R11 100K VCC
MCU
R12 4.7K
All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission. 22
PixArt Imaging Inc.
E-mail: fae_service@pixart.com.tw V3.0, Apr. 2008
PixArt Imaging Inc.
8.3 Power Supply at 1.8V Application Circuit (with IR LED, 27MHz Transceiver)
#1. Battery Power Circuit Optional power source: A or B
A. DC/DC Converter B. Regulator VCC_1.8V ENSW1
BAT_1.5V IR_1.8V Z2
Z2
U2 VIN PAD
ELM9818 COM
VCC_1.8V Z1
L1 220uH D1 1N5819 Z1
VOUT
GND
VIN
IR_1.8V ENCODER
U3 BAT_3.0V
VCC_1.8V
SW1
3
C5 RKEY
C4 SW VOUT
C7 C8 SW2
GND
VCC_1.8V VCC_1.8V
U4
R4
R7 1 8
OSC_RES VDDA 20K
IDSYNC
MOTSWK 2 7
MOTSWK VDD
C17 + C16
SDIO 3 6
0.1uF 10uF S1
SDIO VSS
SCLK 4 5
R1
SCLK LED IR_1.8V
D2 LED
PAW3204DB
R3 10R
#4. RF TX Circuit VCC_1.8V Antenna
All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission. 23
PixArt Imaging Inc.
E-mail: fae_service@pixart.com.tw V3.0, Apr. 2008
PixArt Imaging Inc.
C1 20pF
C3 68pF
C2 + C4
C6 C5 +
2.2uF 10nF U1
1 20 10nF 2.2uF
2 ANT_IN1 ANT_IN2 19
3 AGND VNEG 18
VCC_RF VPOS MDR
4 17
5 VCC LF 16 C7 2.2uF
OSC_IN 6 VDIG AGND 15
C8 + C9 XTAL_IN VPOS_LO
OSC_OUT 7 14
8 XTAL_OUT VNEG_LO 13 B1
10uF 0.1uF VNEG_DIG B1 C11 C10 +
B3 9 12 RF_DATA
10 B3 OUT 11
B2 CLK 10nF 2.2uF
TI TRF7903-PW20
C12 + C13
2.2uF 10nF
OSC_IN OSC_OUT
VCC_RF
C14 X1 C15 VCC_5V VCC_RF
12MHz
47pF 47pF Q1
R1 R2 2N3906
OPEN 0R VCC_RF
B1 B3 U2 R3 10K
1 8
2 A0 VCC 7
A1 WP C16
R4 R5 3 6 SCL R6
4 A2 SCL 5 SDA
GND SDA 0.1uF
0R OPEN 10K
2402 PWR_Ctrl
U3
RF_DATA 1 11 JP1
P0.0 VREG
VCC_RF R7 1.3K
2 15
P0.1 D-/SDATA 1
R8 470
3 16
P0.2 D+/SCLK 2
D1 LED VCC_5V
ID_SYNC 4 14
P0.3 VCC 3
C17 C18
S1 PWR_Ctrl 5 +
P1.0 4
0.1uF 10uF
10 USB
VPP
9
VSS
23 SCL
P0.5
22 SDA
P0.6
12 13
XTALIN XTALOUT
CYPRESS CY7C63723
Figure 17. Application Circuit for RF Receive Using 27MHz Transceiver
All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission. 24
PixArt Imaging Inc.
E-mail: fae_service@pixart.com.tw V3.0, Apr. 2008
PixArt Imaging Inc.
It is not guaranteed that the performance of the mouse sensor with IR LED is as good as the mouse sensor with
red LED. The mouse sensor is designed to a very good match with red LED, and this combination has the best
performance.
8.6.3 Summary
R1
Light Source LED Bin Grade VLED
Min. Typ. Max.
Red LED P, Q 2.7 6.8 22 -
IR LED TBD 1.8 3.3 22 -
All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission. 25
PixArt Imaging Inc.
E-mail: fae_service@pixart.com.tw V3.0, Apr. 2008
PixArt Imaging Inc.
9. Package Information
9.1 Package Outline Drawing
8 7 6 5
1 2 3 4
5.15
0.203
0.25
Max. 0.1 0.010
1.42 Max. 0.004
0.056 0.46
0.018
Max. 12
12.60 +/-0.2
0.496
2.0
0.078
1.01
1.0
0.040
0.039
1 2 3 4
4.55
0.179
5.0 NOTES:
8 7 6 5 0.196
1. All dimensions in MM/INCH.
2. All dimensions tolerance: +/- 0.10mm
4.45 0.80 3. Maxmumflash: +0.2mm
0.175 0.031 4. Angular tolerance: +/- 3.0degress
2.0
0.078
All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission. 26
PixArt Imaging Inc.
E-mail: fae_service@pixart.com.tw V3.0, Apr. 2008
PixArt Imaging Inc.
7.544
11.05 0 ref. 26.010
0.297
6.172 0.435 16.95 1.024
0.243 0.667
4.242
0.167 8 7 6 5
1.194
0.711 0.047
0.028
Optical Center
0 ref.
1.194
0.047
4.242 1 2 3 4
0.167
6.172
0.243 0.711
0.028
7.544
3.251 0.297
0.128
Note: The Part No. of the Mouse Product with Prefix "PAN" shall NOT be made, sold, offered to sell, imported
or used in or into USA, Canada, Japan and EU. For "PAN", PixArt has only gained territory-limited patent
license from Avago. Avago reserve right to take legal action against our customers who fails to comply the
above term. PLEASE NOTE THAT PixArt will NOT defend, indemnify, or provide any assistance to our
customers who fail to comply the term. IF YOU DO NOT AGREE THE TERM, PIXART WILL NOT
DELIVER "PAN" PRODUCTS TO YOU.
All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission. 27
PixArt Imaging Inc.
E-mail: fae_service@pixart.com.tw V3.0, Apr. 2008