Вы находитесь на странице: 1из 66

FILE NO.

SM-CTV-O-056

COLOR TELEVISION
SERVICE MANUAL
MODEL NO. PF2720/PF2730
PF3220/PF3230
CHASSIS NO. CH-16CD

Please read this manual carefully before service.


SERVICE MANUAL

TABLE OF CONTENTS

SAFETY INSTRUCTIONS AND MAINTENANCE ..................................... 1


X-Ray Radiation Precaution .............................................................................................. 1
Safety Precaution ................................................................................................................ 1
Product Safety Notice ......................................................................................................... 2
Maintenance ......................................................................................................... 3

SPECIFICATIONS .......................................................................................................... 4
KEY ICS AND ASSEMBLIES ................................................................................. 4
SYSTEM BLOCK DIAGRAMS............................................................................... 5
Structure Block Diagram .................................................................................................... 5
Block Diagram for Supply Voltage System ..................................................................... 6

SERVICE DATA ............................................................................................................... 7


Technical Data of Key ICs .................................................................................................. 7
Service Data of Key ICs ..................................................................................................... 22
Waveforms of Key Points ................................................................................................... 29

ADJUSTMENTS .............................................................................................................. 37
Set-up Adjustments ............................................................................................................. 37
Circuit Adjustments ............................................................................................................. 40
Service Mode and Bus Data.............................................................................................. 41

TROUBLESHOOTING FLOW CHARTS ......................................................... 47

APPENDIX
1. Circuit Diagrams
2. Printed Circuit Board Diagrams
3. Final Wiring Diagrams
4. Exploded Views

2
SAFETY INSTRUCTIONS AND MAINTENANCE

WARNING: BEFORE SERVICING THIS CHASSIS, READ THE “ X-RAY RADIATION


PRECAUTION ” , “ SAFETY PRECAUTION ” AND “ PRODUCT SAFETY NOTICE ”
INSTRUCTIONS BELOW.

X-RAY RADIATION PRECAUTION


1. The EHT must be checked every time the TV is serviced to ensure that the CRT does not emit
X-ray radiation as result of excessive EHT voltage. The maximum EHT voltage permissible in
any operating circumstances must not exceed the rated value. When checking the EHT, use
the High Voltage Check procedure in this manual using an accurate EHT voltmeter.
2. The only source of X-RAY radiation in this TV is the CRT. The TV minimizes X-RAY radiation,
which ensures safety during normal operation. To prevent X-ray radiation, the replacement
CRT must be identical to the original fitted as specified in the parts list.
3. Some components used in this TV have safety related characteristics preventing the CRT from
emitting X-ray radiation. For continued safety, replacement component should be made after
referring the PRODUCT SAFETY NOTICE below.
4. Service and adjustment of the TV may result in changes in the nominal EHT voltage of the
CRT anode. So ensure that the maximum EHT voltage does not exceed the rated value after
service and adjustment.

SAFETY PRECAUTION
WARNING: REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.
1. The TV has a nominal working EHT voltage. Extreme caution should be exercised when
working on the TV with the back removed.
1.1 Do not attempt to service this TV if you are not conversant with the precautions and
procedures for working on high voltage equipment.
1.2 When handling or working on the CRT, always discharge the anode to the TV chassis before
removing the anode cap in case of electric shock.
1.3 The CRT, if broken, will violently expel glass fragments. Use shatterproof goggles and take
extreme care while handling.
1.4 Do not hold the CRT by the neck as this is a very dangerous practice.
2. It is essential that to maintain the safety of the customer all power cord forms be replaced
exactly as supplied from factory.
3. Voltage exists between the hot and cold ground when the TV is in operation. Install a suitable
isolating transformer of beyond rated overall power when servicing or connecting any test
equipment for the sake of safety.

1
SERVICE MANUAL

4. When replacing ICs, use specific tools or a static-proof electric iron with small power (below
35W).
5. Do not use a magnetized screwdriver when tightening or loosing the deflection yoke assembly
to avoid electronic gun magnetized and decrement in convergence of the CRT.
6. When remounting the TV chassis, ensure that all guard devices, such as nonmetal control
buttons, switch, insulating sleeve, shielding cover, isolating resistors and capacitors, are
installed on the original place.
7. Replace blown fuses within the TV with the fuse specified in the parts list.
8. When replacing wires or components to terminals or tags, wind the leads around the terminal
before soldering. When replacing safety components identified by the international hazard
symbols on the circuit diagram and parts list, it must be the company-approved type and must
be mounted as the original.
9. Keep wires away from high temperature components.

PRODUCT SAFETY NOTICE


CAUTION: FOR YOUR PROTECTION, THE FOLLOWING PRODUCT SAFETY NOTICE
SHOULD BE READ CAREFULLY BEFORE OPERATING AND SERVICING THIS TV SET.
1. Do not slap or beat the cabinet or CRT, since this may result in fire or explosion.
2. Never allow the TV sharing a plug or socket with other large-power equipment. Doing so may
result in too large load, thus causing fire.
3. Do not allow anything to rest on or roll over the power cord. Protect the power cord from being
walked on, modified, cut or pinched, particularly at plugs.
4. Do not place any objects, especially heavy objects and lightings, on top of the TV set. Do not
install the TV near any heat sources such as radiators, heat registers, stove, or other
apparatus that produce heat.
5. Service personnel should observe the SAFETY INSTRUCTIONS in this manual during use
and servicing of this TV set. Otherwise, the resulted damage is not protected by the
manufacturer.
6. Many electrical and mechanical components in this chassis have special safety-related
characteristics. These characteristics are often passed unnoticed by a visual inspection and
the X-ray radiation protection afforded by them cannot necessarily be obtained by using
replacements rated at higher voltages or wattage, etc. Components which have these special
safety characteristics in this manual and its supplements are identified by the international
hazard symbols on the circuit diagram and parts list. Before replacing any of these
components read the parts list in this manual carefully. Substitute replacement components
which do not have the same safety characteristics as specified in the parts list may create
X-ray radiation.

2
SERVICE MANUAL

Safety Symbol Description


The lightning symbol in the triangle tells you that the voltage inside this product may
be strong enough to cause an electric shock. Extreme caution should be exercised
when working on the TV with the back removed.
This is an international hazard symbol, telling you that the components identified by
the symbol have special safety-related characteristics.
FDA This symbol tells you that the critical components identified by the FDA marking have
special safety-related characteristics.
UL This symbol tells you that the critical components identified by the UL marking have
special safety-related characteristics.

MAINTENANCE
1. Install the TV set on a stable and level surface. Do not place the set near or over a radiator or
heat register, or where it is exposed to direct sunlight.
2. Do not install the TV set in a place exposed to rain, water, excessive dust, mechanical
vibrations or impacts.
3. Allow enough space (at least 10cm) between the TV and wall or enclosures for proper
ventilation.
4. Slots and openings in the cabinet should never be blocked by clothes or other objects.
5. Please power off the TV set and disconnect it from the wall immediately if any abnormal
condition are met, such as bad smell, belching smoke, sparkling, abnormal sound or no
picture/sound/raster. Hold the plug firmly when disconnecting the power cord.
6. Unplug the TV set from the wall outlet before cleaning or polishing it. Use a dry soft cloth for
cleaning the exterior of the TV set or CRT screen. Do not use liquid cleaners or aerosol
cleaners.

3
SERVICE MANUAL

SPECIFICATIONS

MODEL PF2720 PF2730 PF3220 PF3230


Television System NTSC-M
Channel Coverage VHF 2-13, UHF 14~69
Mid Band (A-8~A-1, A~I)/Super Band (J~W)
Cable TV Coverage
Hyper Band (AA~ZZ, AAA, BBB)/Ultra Band (65~94, 100~125)
Channels Preset 181
Antenna Input 75 ohm (unbalanced)
21.26x 15.94 in 25.20x 18.82 in
Screen Dimensions
540x405 mm 640x478 mm
Audio Output 5W+5W 5W+5W
Power Source ~120Vac 60Hz
Unit Weight 97.9lbs. ( 44.5kg) 156lbs. ( 71kg)
29.09x22.83x19.29 in. 33.70x26.34x22.05 in.
Unit Dimensions
739x580x490mm 856x669x560mm
Packaged 33.07x26.38x23.43in. 40x30.55x27.76in.
Dimensions 840x670x595mm 1016x776x705mm
Power
135W 170W
Consumption

KEY ICS AND ASSEMBLIES


Table 1 Key ICs and Assemblies
Serial No. Position No. Model No. Function Description

1 N201 TDA937X UOC

2 N202 AT24C16 EEPROM

3 NB01 MSP3440G-B8 BTSC

4 N401 TDA8350 Vertical output circuit

5 N361 TDA8944J Sound power amplifier

6 N901 TA1219AN TV/AV switch circuit

7 N902 TC90A49P COMB filter

8 NY01 TDQ6108JF Video amplifier

9 A101 TDQ-6F2-M Tuner

10 IC801 STR-G8626 Power supply circuit

4
SERVICE MANUAL

SYSTEM BLOCK DIAGRAMS


Structure Block Diagram

45V
V

5
SERVICE MANUAL

Block Diagram for Supply Voltage System

6
SERVICE MANUAL

SERVICE DATA
Technical Data of Key ICs
TDA937X (N201)

UOC
1. General Description ratio), black stretching and Dynamic Skin
The various versions of the TDA937X PS/N2 Tone Control
series combine the functions of a video • Integrated chroma band-pass filter with
processor together with a μ-Controller and switchable centre frequency
US Closed Caption decoder. The ICs are • Only one reference (12 MHz) crystal
intended to be used in economy television required for the μ-Controller, Teletext- and
receivers with 90° and 110° picture tubes. the colour decoder
The ICs have supply voltages of 8V and 3.3V • PAL/NTSC colour decoder with automatic
and they are mounted in an S-DIP 64 search system
envelope. • Internal base-band delay line
The features are given in the following feature • RGB control circuit with ‘Continuous Cathode
list. The differences between the various ICs Calibration’, white point and black level offset
are given in the table on page 4. adjustment so that the colour temperature of
the dark and the light parts of the screen can
2. Features be chosen independently.
TV-signal processor • Linear RGB or YUV input with fast blanking
• Multi-standard vision IF circuit with for external RGB/YUV sources. The
alignment-free PLL demodulator Text/OSD signals are internally supplied from
• Internal (switchable) time-constant for the theμ-Controller/Teletext decoder
IF-AGC circuit • Contrast reduction possibility during
• A choice can be made between versions with mixed-mode of OSD and Text signals
mono intercarrier sound FM demodulator and • Horizontal synchronization with two control
versions with QSS IF amplifier. loops and alignment-free horizontal oscillator
• The mono intercarrier sound versions have a • Vertical count-down circuit
selective FM-PLL demodulator which can be • Vertical driver optimized for DC-coupled
switched to the different FM sound vertical output stages
frequencies (4.5/5.5/6.0/6.5 MHz). • Horizontal and vertical geometry processing
The quality of this system is such that the • Horizontal and vertical zoom function for 16 :
external band-pass filters can be omitted. 9 applications
• Source selection between ‘internal’ CVBS and • Horizontal parallelogram and bow correction
external CVBS or Y/C signals for large screen picture tubes
• Integrated chrominance trap circuit • Low-power start-up of the horizontal drive
• Integrated luminance delay line with circuit
adjustable delay time
• Picture improvement features with peaking
(with variable positive/negative overshoot

7
SERVICE MANUAL

3.Pin

8
SERVICE MANUAL

4.Block Diagram

9
SERVICE MANUAL

5.Refer to Table 2 about Functions and Service Data of the IC's Each Pin.

10
SERVICE MANUAL

AT24C16 (N202)
EEPROM
1. Features
・Low Voltage and Standard Voltage Operation Devices Available
5.0 (VCC = 4.5V to 5.5V) ・8-Pin and 14-Pin JEDEC SOIC and 8-Pin PDIP
2.7 (VCC = 2.7V to 5.5V) Packages
2.5 (VCC = 2.5V to 5.5V) 2.Description
1.8 (VCC = 1.8V to 5.5V) The AT24C01A/02/04/08/16 provides
・Internally Organized 128 x 8 (1K), 256 x 8 (2K), 1024/2048/4096/8192/16384 bits of serial
512 x 8 (4K),1024 x 8 (8K) or 2048 x 8 (16K) electrically erasable and programmable read
・2-Wire Serial Interface only memory (EEPROM) organized as
・Bidirectional Data Transfer Protocol 128/256/512/1024/2048 words of 8 bits each.
・100 kHz (1.8V, 2.5V, 2.7V) and 400 kHz (5V) The device is optimized for use in many
Compatibility industrial and commercial applications where low
・Write Protect Pin for Hardware Data Protection power and low voltage operation are essential.
・8-Byte Page (1K, 2K), 16-Byte Page (4K, 8K, The AT24C01A/02/04/08/16 is available in space
16K) Write Modes saving 8-pin PDIP, 8-pin and 14-pin SOIC
・Partial Page Writes Are Allowed packages and is accessed via a 2-wire serial
・Self-Timed Write Cycle (10 ms max) interface. In addition, the entire family is
・High Reliability available in 5.0V (4.5V to 5.5V), 2.7V (2.7V to
Endurance: 1 Million Cycles 5.5V), 2.5V (2.5V to 5.5V) and 1.8V (1.8V to
Data Retention: 100 Years 5.5V) versions.
・Automotive Grade and Extended Temperature

Pin Configurations

11
SERVICE MANUAL

3.Block Diagram

Fig.6

4.Refer to Table 3 about Functions and Data of the IC’s Pins.

12
SERVICE MANUAL

MSP3440G-B8 (NB01)
Multistandard Sound Processor Family
Release Note: Revision bars indicate significant Other processed standards are the Japanese
changes to the previous edition. The hardware FM-FM multiplex standard (EIA-J) and the FM
and software description in this document is Stereo Radio standard.
valid for the MSP34X0G version B5 and Current ICs have to perform adjustment
following versions. procedures in order to achieve good stereo
1. Introduction separation for BTSC and EIA-J.
The MSP34X0G family of single-chip The MSP34X0G has optimum stereo
Multistandard Sound Processors covers performance without any adjustments.
the sound processing of all analog All MSP34X0G versions are pin and
TV-Standards worldwide, as well as the software downward-compatible to the
NICAM digital sound standards. The full TV MSP34X0D. The MSP34X0G further simplifies
sound processing, starting with analog sound controlling software. Standard selection
IF signal-in, down to processed analog AF-out, requires a single I2C transmission only.
is performed on a single chip. Figure 7 shows The MSP34X0G has built-in automatic
a simplified functional block diagram of the Functions: The IC is able to detect the actual
MSP34X0G. sound standard automatically (Automatic
Standard Detection). Furthermore, pilot levels
This new generation of TV sound processing
and identification signals can be evaluated
ICs now includes versions for processing the
internally with subsequent switching between
multichannel television sound (MTS) signal
mono/stereo/bilingual; no I2C interaction is
conforming to the standard recommended by
necessary (Automatic Sound Selection).
the Broadcast Television Systems Committee
The ICs are produced in submicron CMOS
(BTSC). The DBX noise reduction, or
technology.
alternatively MICRONAS Noise Reduction
The MSP34X0G is available in the following
(MNR) is performed alignment free
packages: PLCC68, PSDIP64, PSDIP52, PQFP80
2. Block Diagram and PLQFP64.

Fig. 7 Simplified Functional Block Diagram of the MSP34X0G

3. Refer to Table 4 about Functions and Service Data of MSP34X0G’s Each Pins.

13
SERVICE MANUAL

TDA8350 (N401)
DC-coupled Vertical Deflection and East-West Output Circuit
1. Features ・High EMC immunity due to common mode
・Few external components inputs

・Highly efficient fully DC-coupled vertical output ・Temperature (thermal) protection


・East-West output stage with one single
bridge circuit
conversion resistor.
・Vertical flyback switch
2. General Description
・Guard circuit The TDA8350Q is a power circuit for use
・Protection against: in 90° and 110° colour deflection systems
-short-circuit of the output pins for field frequencies of 50 to 120 Hz. The
-short-circuit of the output pins to Vp circuit provides a DC driven vertical
deflection output circuit, operating as a
highly efficient class G system and an
3. Block Diagram
East-West driver for sinking the diode
modulator current.

VP VO(guard) VFB

+VP

VO(A)

Idrive(pos) +VO(A)
II(set)

VI(FB)
Idrive(neg)
VP

VO(B)
-VO(B)

II(set)
II(set)

VO(SINK)
II(corr)

Fig. 8

4. Refer to Table 5 about Functions and Service Data of TDA8350Q’s Pins.

14
SERVICE MANUAL

TDA8944J (N361)
Audio Power Amplifier
1. General Description 2. Features
The TDA8944J is a dual-channel audio power Few external components
amplifier with an output power of Fixed gain
2 ´ 7 W at a n 8 W load and a 12 V supply. The Standby and mute mode
circuit contains two Bridge Tied Load No on/off switching plops
(BTL) amplifiers with an all-NPN output stage and Low standby current
standby/mute logic. The TDA8944J High supply voltage ripple rejection
comes in a 17-pin DIL-bent-SIL (DBS) power Outputs short-circuit protected to ground,
package. The TDA8944J is supply and across the load
printed-circuit board (PCB) compatible with all Thermally protected
other types in the TDA894x family. Printed-circuit board compatible
One PCB footprint accommodates both the mono
and the stereo products.

3.Block Diagram

Pinning

Fig.10 Pin configuration.


5. Refer to Table 6 about Functions and Service Data of TDA8944J's Pins.

15
SERVICE MANUAL

TA1219AN (N901)
Audio/Video Switching IC for TVs
The TA1219AN is an audio/video switching IC for TV Sets.
Conforming to I2C bus standards, it allows you to
perform various switching operations through the bus
lines by using a microcomputer. Furthermore, since the
presence of a signal on its sync signal output pin can be
determined by a microcomputer , it is possible to check
each input/output channel (self-diagnosis).
This IC has the same pin assignments as the TA1218AN
(SDIP42), a 2-channel output version of the TA1219AN, so
these chips are pin compatible on pins 3 to 20 and 23 to
40 in TA1218AN.

1. Features
・I2C bus control
・Video: 5-channel inputs and 1-channel outputs (2 channels conforming to S system)
・Audio: 5-channel inputs and 2-channel outputs
・Self-diagnostic function
・ADC inputs based on European 21-pin standards
・ADC inputs based on S1/S2 terminal standards
・Switchable subaddress

16
SERVICE MANUAL

2. Block Diagram

Fig.11

3. Refer to Table 7 about Functions and Service Data of TA1219AN’s Pins.

17
SERVICE MANUAL

TC90A49P (N902)
COMB Filter
1. Features
TV format : NTSC (3.58), PAL, M-PAL, and N-
PAL
Dynamic comb filter
Vertical edge enhancement circuit
PLL 8 × multiplier circuit
Internal 8-bit 4 fsc AD converter
Internal 8-bit precision 8 fsc DA converter (2 ch)
Sync tip clamp circuit
Internal 4H-line memory
I 2C bus interface
Package : DIP 20-pin and SOP 24-pin
5 V single power supply

2. Block Diagram

3. Pin Assignment

Fig.14

4. Refer to Table 8 about Functions and Service Data of TC90A49P’s Pins.

18
SERVICE MANUAL

TDA6108JF (NY01)
Triple Video Output Amplifier
1. Features 2. General Description
・Typical bandwidth of 9.0 MHz for an output The TDA6108JF includes three video
signal of 60 V (peak-to-peak value) output amplifiers in one plastic
・High slew rate of 1850 V/µS DIL-bent-SIL 9-pin medium power
・No external components required (DBS9MPF)package (SOT 111-1), using
・Very simple application high-voltage DMOS technology, and is
・Single supply voltage of 200 V intended to drive the three cathodes of a
・Internal reference voltage of 2.5 V colour CRT directly. To obtain maximum
・Fixed gain of 51 performance, the amplifier should be used
・Black-Current Stabilization (BCS) circuit with black-current control.
・Thermal protection.

3. Ordering Information

Type Package
Number Name Description Version
Plastic DIL-bent-SIL medium power package with
TDA6108JF DBS9MPF SOT111-1
fin; 9 leads

4. Block Diagram

Fig.15
5. Refer to Table 8 about Functions and Service Data of TDA6108JF’s Pins.

19
SERVICE MANUAL

STR-G8626 (IC801)
The Series STR-G 86626/5653/F6654 is specifically designed to satisfy the requirements for increased
integration and reliability in off-line quasi-resonant flyback converters. The series incorporates a
high-precise error amplifying control and drive circuit with discrete avalanche-rated power MOSFET,
featuring fewer external components, small-size and standard power supply.
Covering the power range from below 25 watts up to 300 watts for 100/115/230 VAC inputs, and up to
150 watts for 85 to 265 VAC universal input, these devices can be used in a range of applications,
from battery chargers and set top boxes, to televisions, monitors, and industrial power supply units.
Cycle-by-cycle current limiting, under-voltage lockout with hysteresis, over-voltage protection, and
thermal shutdown protects the power supply during the normal overload and fault conditions.
Low-current startup and a low-power standby mode selected from the secondary circuit completes
a comprehensive suite of features. The series is provided in a five-pin overmolded SIP style package,
affording dielectric isolation without compromising thermal characteristics.
1. Features
Flyback Operation with Quasi-Resonant Soft Switching for Low Power Dissipation and EMI
Rugged Avalanche-Rated MOSFET
Soft drive circuit MOSFET
Adjustable MOSFET switching speed
Choice of MOSFET Voltage and Rds(on)
Full Over-Current Protection (no blanking)
Under-Voltage Lockout with Hysteresis
Over-Voltage Protection
Direct Voltage Feedback
Low Start-up Current (100 Amax)
Low-Frequency, Low-Power Standby Operation
Overmolded 5-Pin Package
2 . Circuit Block Diagram

Fig. 16

20
SERVICE MANUAL

  3. Pin Configuration and Functions

Fig.17

3.1) Pin function for STR-G5653/8626

Pin No. Symbol Function Description


1 D MOSFET drain
2 S MOSFET source
3 GND Ground
4 VIN Supply voltage input for control circuit
5 OCP/FB Over-current protection detection signal/ voltage-limiting signal input

3.2) Pin function for STR-F6654

Pin No. Symbol Function Description


1 OCP/FB Over-current protection detection signal/ voltage-limiting signal input
2 S MOSFET source
3 D MOSFET drain
4 VIN Supply voltage input for control circuit
5 GND Ground

4. Refer to Table 9 about Functions and Service Data of the IC’s Pins.

21
SERVICE MANUAL

SERVICE DATA OF KEY ICs


Table 2 Functions and Service Data of TDA9379 (N201)’s Pins
Digital Multimeter
Pin
Functions Description Reference Positive Negative
No.
Voltage (V) Resistance (20KΩ) Resistance (20KΩ)
1 Port 1.3 or Counter/Timer 1 input 0.8 ∞ ∞
2
2 Port 1.6 or I C-bus clock line 4 6.5 6.0
2
3 Port 1.7 or I C-bus data line 4 6.5 6.0
4 Port 2.0 or Tuning PWM output 1.128 13.1 10.2
5 Port 3.0 or ADC0 input or PWM0 output 0.36 ∞ ∞
6 Port 3.1 or ADC1 input or PWM1 output 3.29 1.64 1.64
7 Port 3.2 or ADC2 input or PWM2 output 3.29 1.67 1.67
8 Port 3.3 or ADC3 input or PWM3 output 4.91 7.8 7.3
Digital ground for µ-Controller core and
9 0 0 0
periphery
Port 0.5 (8 mA current sinking capability for
10 0 7.2 6.99
direct drive of LEDs)
Port 0.6 (8 mA current sinking capability for
11 4.17 7.7 7.3
direct drive of LEDs)
Analog ground of Teletext decoder and digital
12 0 0 0
ground of TV-processor
13 Internally connected 2.285 ∞ 0
14 2nd supply voltage TV-processor (+8V) 8.1 1.2 1.4
Supply voltage of digital circuit of
15 4.96 ∞ ∞
TV-processor
16 Phase-2 filter 3.49 ∞ ∞
17 Phase-1 filter 3.81 ∞ ∞
18 Ground 3 for TV-processor 0 0 0
19 Bandgap decoupling 3.96 ∞ ∞
Automatic Volume Levelling (90° versions) /
20 0.78 ∞ ∞
E-W drive output (110° versions) /
Decoupling sound demodulator (QSS version
21 2.3 ∞ ∞
in AM/FM mode)
22 Vertical drive B output 2.3 ∞ ∞
23 Vertical drive A output 1.85 ∞ ∞
24 IF input 1 1.85 ∞ ∞
25 IF input 2 3.82 ∞ ∞
26 Reference current input 3.75 ∞ ∞
27 Vertical sawtooth capacitor 1.36 4.75 4.73
28 Tuner AGC output 1.87 ∞ ∞
29 Audio deemphasis or SIF input 1 1.87 ∞ ∞
(Continued)

22
SERVICE MANUAL

30 Decoupling sound demodulator or SIF input 2 0 0 0


31 Ground 2 for TV processor 2.32 ∞ ∞
32 Narrow band PLL filter or AGC sound IF 0 ∞ ∞
Automatic Volume Levelling / sound IF input /
33 3.1 11.2 10.9
subcarrier reference output / audio
34 Deemphasis 0.75 ∞ ∞
35 Horizontal output 2.60 ∞ ∞
36 Flyback input/sandcastle output 1.47 9.8 9.75
37 External audio output / QSS intercarrier out 2.43 ∞ ∞
38 EHT/overvoltage protection input 2.75 ∞ ∞
39 IF-PLL loop filter 8.1 1.2 1.35
40 IF video output / selected CVBS output 4 ∞ ∞
41 Supply voltage TV processor 0 0 0
42 CVBS/Y input 3.9 ∞ ∞
43 C input 1.55 ∞ ∞
Audio output/AM audio output
44 4.44 ∞ ∞
(volume controlled)
45 2nd RGB / YUV insertion input 1.67 ∞ ∞
46 2nd R input / V (R-Y) input / PR input 2.5 ∞ ∞
47 2nd G input / Y input 2.5 ∞ ∞
48 2nd B input / U (B-Y) input / PB input 2.5 ∞ ∞
49 Beam current limiter input 1.87 ∞ ∞
50 Black current input / V-guard input 5.8 ∞ ∞
51 Red output 2.63 3.1 3.0
52 Green output 2.47 3.1 3.0
53 Blue output 2.69 3.1 3.0
Analog supply of Teletext decoder and digital
54 3.27 0.67 0.65
supply of TV-processor (3.3 V)
55 OTP programming voltage 0 0 0
56 Digital supply to core (3.3 V) 3.28 0.67 0.65
57 Oscillator ground supply 0 0 0
58 Crystal oscillator input 1.58 ∞ ∞
59 Crystal oscillator output 1.67 ∞ ∞
60 Reset 0 0 0
61 Digital supply to periphery (+3.3 V) 3.28 0.67 0.65
62 Port 1.0 or external interrupt 1 input 0 12.9 11.9
63 Port 1.1 or Counter/Timer 0 input 0 7.3 7.1
64 Port 1.2 or external interrupt 0 input 4.59 18.7 18.8

23
SERVICE MANUAL

Table 3 Functions and Service Data of AT24C16 (N202)’s Pins


Digital Multimeter
Pin
Functions Description Reference Voltage Positive Resistance Negative Resistance
No.
(V) (20KΩ) (20KΩ)
1 Address input 0 0 0
2 Address input 0 0 0
3 Address input 0 0 0
4 Common ground 0 0 0
5 Serial data 4 6.37 6.4
6 Serial clock input 4.2 6.37 6.44
7 Write protect 0 0 0
8 Supply voltage 4.9 3.03 3.02
Table 4 Functions and Service Data of MSP3440(N606M)’s Pins
Pin Digital Multimeter
Function Description Reference Voltage Positive Resistance Negative
No. (V) (20KΩ) Resistance (20KΩ)
1 NC 0.00 15.32 5.3
2 NC 2.57 13.41 5.51
3 NC 0.00 15.32 5.57
4 NC 0.00 15.32 5.58
5 ADR-SEL 5.03 8.62 4.54
6 STANDBYQ 5.03 8.63 4.54
2 3.8 6.98 4.44
7 I C-DC
2 3.9 6.98 4.44
8 I C-DA
9 NC 2.5 15.32 6.24
10 NC 2.82 15.32 6.24
11 NC 2.5 15.32 6.24
12 NC 0.27 15.32 5.29
13 NC 0.2 15.32 5.59
14 NC 0.1 15.32 5.59
15 NC 0.1 15.32 5.59
16 DVSUP 5.04 8.6 4.54
17 DVSS 0.00 0.00 0.00
18 NC 0.00 15.32 5.31
19 NC 0.00 ∞ ∞
20 RESETQ 5 15.04 5.24
21 NC 0.00 3.54 3.54
22 NC 0.00 3.52 3.52
23 VREF2 0.00 0.00 0.00
24 DACM-R 2.03 3.52 3.52
25 DACM-L 2.04 3.54 3.54
26 NC 1.41 3.6 3.6

(Continued)

24
SERVICE MANUAL

27 NC 3.81 13.8 5.92


28 NC 3.79 13.8 5.91
29 GND 0.00 0.00 0.00
30 SC1-OUT-R 3.8 12.8 5.91
31 SC1-OUT-L 3.79 12.8 5.92
32 CAPL-A 7.28 ∞ 6.04
33 AHVSUP 8.26 ∞ 4.59
34 CAPL-M 6.53 ∞ 6.04
35 AHVSS 0.00 0.00 0.00
36 ABNDC 3.74 ∞ 6.02
37 NC 3.77 ∞ 6.1
38 NC 3.77 ∞ 6.1
39 NC 3.77 ∞ 6.1
40 NC 3.77 ∞ 6.1
41 SC1-IN-L 3.77 ∞ 6.1
42 SC1-IN-R 3.77 ∞ 6.1
43 VREFTOP 2.61 1.63 1.63
44 NC 3.77 19.42 6.1
45 AVSS 0 0.00 0.00
46 AVSUP 5.13 8.62 4.53
47 ANA-IN1+ 1.52 15.3 5.27
48 ANA-IN1- 1.52 15.3 5.26
49 ANA-IN2+ 0.00 15.3 5.27
50 TESTEN 0.00 0.00 0.00
51 XTAL-IN 2.49 14.79 5.27
52 XTAL-OUT 2.49 14.63 5.3

Table 5 Functions and Service Data of TDA8350Q-N6 (N401)’s Pins

Digital Multimeter
Pin No. Function Description Reference Positive Resistance Negative
Voltage (V) (20KΩ) Resistance (20KΩ)
1 Vertical drive input (positive) 2.33 8.82 5.8
2 Vertical drive input (negative) 2.28 8.83 5.83
3 Feedback input 8.52 5.74 4.71
4 Supply voltage 17.23 7.92 4.2
5 Output 1 8.5 5.83 4.71
6 Not connected 0.00 ∞ ∞
7 Ground 0.00 0.00 0.00
8 Pump supply voltage input 49.31 ∞ ∞
9 Output 2 0.00 5.87 4.7
10 Guard output 0.2 8.64 5.88
11 Pincushion output 0.07 9.79 5.24
12 Pincushion input (negative) 2.43 ∞ 6.97
13 Pincushion input (positive) 2.91 ∞ 6.88

25
SERVICE MANUAL

Table 6 Functions and Service Data of TDA8944J (N361)’s Pins


Digital Multimeter
Pin
Functions Description Reference Voltage Positive Resistance Negative Resistance
No.
(V) (20KΩ) (20KΩ)
1 Negative loudspeaker terminal 1 7.98 ∞ ∞
2 Ground channel 1 0 0 0
3 Supply voltage channel 1 14.9 5.8 7.7
4 Positive loudspeaker terminal 1 7.3 ∞ ∞
5 Not connected 0 ∞ ∞
6 Positive input 1 7.3 ∞ ∞
7 Not connected 0 ∞ ∞
8 Negative input 1 7.4 ∞ ∞
9 Negative input 2 7.3 ∞ ∞
Mode selection input (standby,
10 0 7.8 8.9
mute, operating)
Half supply voltage decoupling
11 7.6 ∞ ∞
(ripple rejection)
12 Positive input 2 7.3 ∞ ∞
13 Not connected 0 ∞ ∞
14 Negative loudspeaker terminal 2 7.3 ∞ ∞
15 Ground channel 2 0 0 0
16 Supply voltage channel 2 14.8 3.5 3.5
17 Positive loudspeaker terminal 2 7.3 ∞ ∞

Table 7 Functions and Service Data of TA1219AN (DS01)’s Pins

Digital Multimeter
Pin Negative
Function Description Reference Positive
No.
Voltage(V) Resistance(20KΩ) Resistance(20 KΩ)
1 Get Select 6.54 7.88 5.77
2 Get Select 3.69 7.99 5.73
3 Lin TV 5.12 7.49 5.89
4 Rin TV 5.11 7.55 5.91
5 Vin TV 5.13 7.52 5.89
6 LinTV1 5.12 7.63 5.89
7 RinTV1 5.12 7.63 5.89
8 VinTV1 5.13 7.52 5.89
9 LinS1 5.12 7.64 5.89
10 Y/Vins1 5.09 7.5 5.89
11 RinS1 5.1 7.64 5.88
12 CinS1 0.00 0.00 0.00
13 LinS2 5.08 7.64 5.87
14 Y/VinS2 5.13 7.62 5.87

26
SERVICE MANUAL

15 RinS2 5.11 7.62 5.86


16 CinS2 5.12 7.66 5.64
17 I/01 7.3 7.98 5.43
18 I/02 0.02 7.9 5.44
19 GND 0.00 0.006.98 0.00
20 Scl 3.5 6.98 4.47
21 SDA 3.77 6.98 4.46
22 Sync out 0.02 7.88 5.45
23 Address 0.00 0.00 0.00
24 VinV2 5.11 7.53 5.81
25 LinTV2 5.1 7.64 5.82
26 Yin 5.1 7.76 5.82
27 RinV2 5.1 7.64 5.82
28 Vin 5.09 7.76 5.6
29 Vcc 5.86 5.45 4.1
30 Cout 3.46 0.2 0.2
31 Rout1 3.95 7.43 5.46
32 Yout 3.48 0.2 0.2
33 Lout1 3.96 7.43 5.46
34 Vout1 4.06 0.2 0.2
35 RoutTV 3.95 7.39 5.48
36 LoutTV 3.95 7.46 5.48

Table 8 Functions and Service Data of TC90A49P (N902)’s Pins


Pin Digital Multimeter
Functions Description Reference Positive Resistance Negative Resistance
No.
Voltage (V) (20KΩ) (20KΩ)
1 ADC and DAC analog power supply. 4.98 0.55 0.54
ADC bias voltage. Stabilize by attaching a 0.01µF
2 1.41 ∞ ∞
capacitor.
ADC input range D upper limit voltage. Stabilize
3 3.15 0.64 0.63
by attaching a 0.01µF capacitor.
ADC input. Inputs 1.0 Vp-p video signal. Sync tip
4 2.14 ∞ ∞
clamp is performed.
ADC input range D lower limit voltage. Stabilize by
5 1.84 0.497 0.49
attaching a 0.01µF capacitor.
6 ADC and DAC logic power supply. 4.98 0.55 0.55
7 Logic and internal DRAM GND (digital). 0 0 0
8 Internal DRAM power supply 4.98 0.55 0.55
2
9 I C BUS SDA 4.12 6.39 6.44
2
10 I C BUS SCL 4.25 6.4 6.45
Shipment test mode switch or I2C bus setting
11 0 0 0
reset pin.
12 Y signal comb function ON / OFF switch. 0 0 0

(Continued)

27
SERVICE MANUAL

13 Clock input pin. 2.54 ∞ ∞


14 Connect the APC filter in the 8 fsc PLL circuit 0 ∞ ∞
15 PLL power supply 4.98 0.55 0.55
16 ADC, DAC, and PLL GND (analog). 0 0 0
17 Outputs chrominance signal. 2.25 ∞ ∞
18 DAC output range D upper limit voltage. 3.14 0.57 0.57
19 DAC output range D lower limit voltage 1.84 0.42 .043
20 Outputs luminance signal. 2.16 ∞ ∞

Table 9 Functions and Service Data of TDA6108JF (NY01)’s Pins


Digital Multimeter
Pin
Functions Description Reference Voltage Positive Resistance Negative Resistance
No.
(V) (20KΩ) (20KΩ)
1 G inverting input 1.81 3.03 2.99
2 R inverting input 1.91 3.1 3.0
3 B inverting input 2.0 3.03 2.99
4 Ground 0 0 0
5 Black level current input 3.33 ∞ ∞
6 Supply voltage 196.7 ∞ ∞
7 B output 152.5 ∞ ∞
8 R output 157.5 ∞ ∞
9 G output 159.9 ∞ ∞

Table 10 Functions and Service Data of STR-G8626 (IC801)’s Pins


Digital Multimeter
Pin
Functions Description Reference Voltage Positive Resistance Negative Resistance
No.
(V) (20KΩ) (20KΩ)
1 D 146.3 ∞ ∞
2 S 0 0 0
3 GND 0 0 0
4 Vin 31.96 ∞ ∞
5 DCP/FB 1.72 0.699 0.166

28
SERVICE MANUAL

Waveforms of Key Points

N201’s Pin2

N201’s Pin3

29
SERVICE MANUAL

N201’s Pin22

N201’s Pin32

30
SERVICE MANUAL

N201’s Pin33

N201’s Pin34

31
SERVICE MANUAL

N201’s Pin38

N201’s Pin42

32
SERVICE MANUAL

N201’s Pin43

N201’s Pin59

33
SERVICE MANUAL

NB01’s Pin47

NB01’s Pin52

34
SERVICE MANUAL

N401’s Pin5

N401’s Pin9

35
SERVICE MANUAL

N401’s Pin11

36
SERVICE MANUAL

ADJUSTMENTS

Set-up Adjustments

●The following adjustments should be made when a complete realignment is required or a new
CRT is installed. Perform the adjustments in order as follows.
1. Color purity
2. Convergence
3. White Balance
Note:
The purity/convergence magnet assembly and rubber wedges need mechanical positioning.
Refer to Fig. 18.

1. Color Purity Adjustment


Note:
Before attempting any purity adjustment, the TV should be operated for at least 15 minutes.
1) Demagnetize the CRT and cabinet using a degaussing coil.
2) Set the brightness and contrast to maximum.
3) Receive the green raster test pattern.
4) Loosen the clamp screw holding the deflection yoke and slide it backward or forward to display
vertical green belt (zone) on the screen.
5) Remove the rubber wedge.
6) Rotate and spread the tabs of the purity magnet around the neck of the CRT until the green belt
is on the center of the screen.
7) Slowly move the deflection yoke forward or backward until a uniform green screen is obtained.
Tighten the clamp screw of the yoke temporarily.
8) Check purity of the red and blue raster.

Yoke

Fig. 18

37
SERVICE MANUAL

Fig. 19

2. Convergence Adjustment
Note:
Before attempting any convergence adjustment, the TV should be operated for at least 15
minutes.
●Center convergence adjustment
1) Receive the crosshatch test pattern.
2) Set the brightness and contrast properly.
3) Adjust two tabs of the 4-pole magnet to change the angle between them and red and blue
vertical lines are superimposed on the center area of the screen.
4) Turn both tabs at the same time keeping the angle constant to superimpose red and blue
horizontal lines on the center of the screen.
5) Adjust two tabs of 6-pole magnet to superimpose red/blue line and green line. Adjusting the
angle affects the vertical lines and rotating both magnets affects the horizontal lines.
6) Repeat steps 3)~5) keeping in mind red, green and blue movement. 4-pole magnet and 6-pole
magnet interact each other, resulting in complicating and dot movement.

●Circumference convergence adjustment


1) Loosen the clamping screw of the defection yoke slightly to allow it to tilt.
2) Temporarily put a wedge as shown in Fig.18. (Do not remove cover paper on adhesive part of
the wedge.)
3) Tilt front of the deflection yoke up or down to obtain better convergence in circumference.
Push the mounted wedge into the space between the CRT and yoke to fix the yoke temporarily.
4) Put other wedge into bottom space and remove the cover paper to stick.
5) Tilt front of the deflection yoke right or left to obtain better convergence in circumference.
6) Keep the deflection yoke position and put another wedge in either upper space. Remove cover
paper and stick the wedge on the CRT to fix the yoke.
7) Detach the temporarily mounted wedge and put it in another upper space. Stick it on the CRT to
fix the yoke.
8) After fixing three wedges, recheck overall convergence.

38
SERVICE MANUAL

Tighten the screw firmly to fix the yoke and check if the yoke is fixed.
9) Stick three adhesive tapes on wedges as shown in Fig. 18.

4-pole Magnet Movement 6-pole Magnet Movement

Center Convergence by Convergence Magnets

Incline the Yoke Up (or Down) Incline the Yoke Right (or Left)
Circumference Convergence by DEF Yoke

Fig.20

Circuit Adjustments
1. General Description
All adjustments are thoroughly checked and corrected before the TV outgoing. Therefore the TV
should operate normally and deliver proper color pictures upon installation. However, several
minor adjustments may be required depending on the particular location where the TV is
operated.
This TV is shipped completely in carton. Carefully take out the TV from the carton and remove
all packing materials. Connect the power cord into a 120V AC, 60Hz two-pin power outlet. Turn
on the TV. Check and adjust all the customer controls such as brightness, contrast and color to
obtain natural color pictures.

2. Automatic Degaussing

39
SERVICE MANUAL

A degaussing coil is mounted around the CRT so that external degaussing after moving the TV
is generally unnecessary, providing it is properly degaussed upon installation. The degaussing
coil operates in about 1 second after power on. If the set is moved or faced to a different
direction, the power switch must be switched off for at least 30 minutes in order that the
automatic degaussing circuit operates properly. Should the chassis or parts of the cabinet
become magnetized to cause poor color purity, use an external-degaussing coil. Slowly move
the degaussing coil around the screen, the sides and front of the TV and slowly withdraw the coil
to a distance of about 2m before unplug it. If color shading still exists, perform the Color Purity
Adjustment and Convergence Adjustment procedures.

3. Supply Voltage Adjustment


Caution: +B voltage has close relation to high voltage. To avoid X-ray radiation, +B voltage
should be +145V.
1) AC power supply to 120±2V.
2) Connect a digital voltmeter to two pins of C820, and then turn on the TV.
3) Receive Philips test pattern.
4) The voltmeter should be read 145±1.5V.

4. High Voltage Inspection


Caution: No high voltage adjustment should be done in the chassis.
1) Connect a precise high voltmeter to the second anode of the CRT.
2) Turn on the TV and set the brightness and contrast to minimum (i.e. set beam current of the
CRT to zero).
3) The high voltage tested should be 29±1KV (For 29” CRTs) or 31±1KV (for 34” CRTs).
4) Set the brightness to minimum or maximum, and ensure high voltage not beyond limitation of
32KV (for Samsung and LG 29” CRTs), 33 KV(for Daewoo and Toshiba 29” CRTs) or 35KV (for
34” CRTs).
5. Focus Adjustment
1) Use the remote control to set the contrast to maximum and the brightness,color to medium.
2) Set H. V. lines near center of Philips pattern to thinnest with the FCB on the FBT. After finishing
adjustment,ensure that no poor focusing exists near the center or around of the frame.

Before Adjusting After Adjusting

40
SERVICE MANUAL

Service Mode and Bus Data


1. How to Enter the Service Mode with the Remote Control
1) Decrease volume to 0.
2) Press the MUTE button on the remote control and VIDEO button on the TV at the same time.
3) Adjust the TV with the MENU SELECT buttons on the remote control.
4) Press the button on the remote control to quit the Service mode.

2. Bus Data
Symbol Adjustment Description
S0 OP1 190 Option bit 1(See “Option Set”)
OP2 15 Option bit 2(See “Option Set”)
OP3 1 Option bit 3(See “Option Set”)
OP4 221 Option bit 4(See “Option Set”)
OP5 140 Option bit 5(See “Option Set”)
OP6 111 Option bit 6(See “Option Set”)
OP7 191 Option bit 7(See “Option Set”)
OP8 101 Option bit 8(See “Option Set”)
S1 PAR Set to optimum Parallelogram correction
BOW Set to optimum Bow correction
HSH Set to optimum Horizontal shift
EWW Set to optimum East-west width adjustment
EWP Set to optimum East-west pincushion correction
UCR Set to optimum Upper corner correction
LCR Set to optimum Lower corner correction
EWT Set to optimum East-west Trapezoidal correction
S2 VSL Set to optimum Half vertical output
VAM Set to optimum Vertical amplitude
SCL Set to optimum Vertical linearity
VSH Set to optimum Vertical shift
VOF Set to optimum Vertical position of character
CCV Set to optimum Vertical position of CCD
HOF Set to optimum Horizontal position of character
CCHF Set to optimum Horizontal position of CCD
S3 VX 25
RED Set to optimum Red gun cutoff voltage
GRN Set to optimum Green gun cutoff voltage
WPR Set to optimum Red gun drive voltage
WPG Set to optimum Green gun drive voltage
WPB Set to optimum Blue gun drive voltage
(Continued)

41
SERVICE MANUAL

YDFN 7 Luminance delay


TOP Set to optimum Video automatic gain control
VOL 31 UOC volume control
IFFS 1 Picture intermediate frequency
HDOL 13 Cathode drive voltage
HD-B 3 Brightness of blue back
S4
AGC 2 Automatic gain control velocity
VG2B 32
FEAT 57 See “Option Set”.
FEAT1 56 See “Option Set”.
TRE1 100 Treble Max.
TRE2 50 Treble Mid.
BAS1 60 Bass Max.
BAS2 30 Bass Mid.
S5
1CON 80 Contrast in Normal mode
1BRI 50 Brightness in Normal mode
1COL 50 Color in Normal mode
1SHP 50 Sharpness in Normal mode
S6 2CON 100 Contrast in Movie mode
2BRI 40 Brightness in Movie mode
2COL 60 Color in Movie mode
2SHP 60 Sharpness in Movie mode
3CON 100 Contrast in Sports mode
3BRI 60 Brightness in Sports mode
3COL 40 Color in Sports mode
3SHP 40 Sharpness in Sports mode
S7 PP H 0
IFOF Set to optimum IF offset
VENH 1 Vertical enhancement
COR 3 Coring
S8 VOLA 70 Volume 25
VOLB 80 Volume 50
VOLC 90 Volume 75
VOLD 100 Volume 100
WFRA 70 Woofer 25
WFRB 80 Woofer 50
WFRC 90 Woofer 75
WFRD 100 Woofer 100
S9 SAGC 0 Sound AGC
LOUD 40 1KHz(or 2KHz) sound AGC
SCOT 107 AV output volume
(Continued)

42
SERVICE MANUAL

SCIN 61 AV input volume


FMIN 63 Sound frequency modulation
WOCF 15 Woofer Mid.
SAV CON1 100 Contrast Max.
CON2 50 Contrast Min.
BRI1 Set to optimum Brightness Max.
BRI2 Set to optimum Brightness Min.
COL1 100 Color Max.
COL2 50 Color Min.
SHP1 80 Sharpness Max.
SHP2 40 Sharpness Min.
Notes:
① “5”or “6”will be displayed before the data depending on signal frequency (50Hz or 60Hz)
during geometric data adjustment.
② The data sheet may differ dependent on different models.
③ The data sheet may differ dependent on different CRTs for the same model.

3. Option Set
Bit Item Description Default
OP1 0 TA1343N Sound processor TA1343N: 1→Yes, 0→No 0
1 MSP3440G MSP3440G: 1→Yes, 0→No 1
2 IDENT_TXT12 1→TXT12 IDENT detection, 0→SL IDENT detection 1
3 COMB_FILTER TC90A49P: 1→Yes, 0→No 1
4 OP_X_RAY X-Ray protection: 1→Yes, 0→No 1
5 UOC_SVM TDA9379-VM: 1→Yes, 0→No 1
6 TDA9859 Sound processing chip TDA9859: 1→Yes, 0→No 0
7 SOUND_CHIP Sound processing chip: 1→Yes, 0→No (PWM control) 1
OP2 0 TV_29_21 Definition of UOC pin: 1→29”, 0→21” 1
1 VCHIP V-chip: 1→Yes, 0→No 1
2 CCD Closed Caption: 1→Yes, 0→No 1
3 SOUND_EFFE Audio options: 1→Yes, 0→No 1
CT
4 OP-ZOOM-DE ZOOM detection:1→No, 0→Yes 0
LE-LINE
5 0
6 0
7 OP-LOGO User LOGO display: 1→Yes under no signal condition, 0
0→No
OP3 0 BLUE_BACK Blue back under no signal condition: 1→Yes, 0→No 1
1 VM_OSD 1→Dependent on OSD MENU, 0→Independent on 0
OSD
2 TILT Tilt: 1→Yes, 0→No 0
3 WOOFER_ON Super woofer: 1→Yes, 0→No 0
OFF
(Continued)

43
SERVICE MANUAL

4 WOOFER_VOL Super woofer volume control: 1→Yes, 0→No 0


5 0
6 0
7 OP-TIMER TIMER: 1→Yes, 0→No 0
OP4 0 ENGLISH English: 1→Yes, 0→No 1
1 PORTUGUESE Portuguese: 1→Yes, 0→No 0
2 FRENCH French: 1→Yes, 0→No 1
3 SPANISH Spanish: 1→Yes, 0→No 1
4 MSP3440G Auto volume control: 1→Yes, 0→No 1
-AVC
5 MSP3440G- MDB: 1→Yes, 0→No 0
MDB
6 MSP3440G- Five equalizer: 1→Yes, 0→No 1
TONE
7 MSP3440G Frequency gain enhancement: 1→1KHz, 0→2KHz 1
_GAIN
OP5 0 PAL_M_N PAL M /PAL N: 1→Yes, 0→No 0
1 Power-on 1→4 seconds, 0→Every 0
degaussing
2 AV_STEREO AV Stereo: 1→Yes, 0→No 1
3 16:9 16 : 9: 1→Yes, 0→No 1
4 LOCK_MENU LOCK_MENU 1→Yes, 0→No 0
5 BSCREEN Black screen when changing channels: 1→Yes, 0→ 0
No
6 WOOFER_MAI Woofer available on main channel1(343): 1→Yes, 0→ 0
N No
7 CHANNELLAB Channel label: 1→Yes, 0→No 1
EL
OP6 0 FMWS FM-PLL window: 1→Large, 0→Small 1
1 FSL Vertical sync: 1→60%, 0→Noise detector 1
2 OSO Switch off: 1→Overscan, 0→Undefined 1
3 YPRPB YPbPr selection: 1→Yes, 0→No 1
4 VG2_MODE VG2 adjustment: 1→UOC H, 0→UOC I 0
5 SYNC_Y DVD sync separately: 1→Yes, 0→No 1
6 QSS 1→QSS, 0→FM 1
7 0
OP7 0 AV2 AV2: 1→Yes, 0→No 1
1 AV3 AV3: 1→Yes, 0→No 1
2 AV4 AV4: 1→Yes, 0→No 1
3 SVHS1 SVHS1: 1→Yes, 0→No 1
4 SVHS4 SVHS4: 1→Yes, 0→No 1
5 DVD DVD: 1→Yes, 0→No 1
6 LAST_SOURC Turn-on mode after power-on: 1 → TV, 0 → Last 0
E program source
(Continued)

44
SERVICE MANUAL

7 STANDBY Standby mode after power-on: 1→Standby, 0→The 1


same as last power-off mode
OP8 0 VM Velocity modulation: 1→Yes, 0→No 1
1 LOCK Lock used for identifying detection: 1→Yes, 0→No 0
2 IDENT_MODE Lock handle: 1→TXT12 | Lock; 0→TXT12 & Lock 0
3 COLOR Matrix: 1→USA; 0 →Japan 0
MATRIX
4 FORF F/S 00→AUTO 60 01→60 FORCED 0
5 FORS 10→AUTO LAST 11→AUTO 50 1
6 CHILD_LOCK Child lock: 1→Yes, 0→No 1
7 SPEAKER Speaker On/Off: 1→Yes, 0→No 0
FEA 0 BKS Black level stretch 1
T 1 0 0
2 0 0
3 DSK Skin tone correction 1
4 COR0 Dynamic coring: 00→Off 11→Max. 1
5 COR1 1
6 SVM0 TDA9379 VM delay 00→50 01→70 0
10→90 11→Spare
7 SVM1 0
FEA 0 0 0
T1 1 0 0
2 VAM0 TDA9379 VM amplitude: 00→OFF 01→0.8V 0
10→1.2V 11→1.8V
3 VAM1 1
4 RPO0 Over pulse/preset pulse 00(1:1) 01(1:1.25) 1
5 RPO1 10(1:1.5) 11(1:1.8) 1
6 0 0
7 0 0

Notes:
① The option data in the above table may differ depending on models, UOC chips and CRTs
used.
② It is required to check if the data comply with the function requirements of your TVs.
For example:
③ For PF2720 and PF3220 models, OP1 is set to 158, OP7 to 175 and OP8 to 100 when using
TDA9375 or OP1 is set to 158, OP7 to 175 and OP8 to 100 when using TDA9379.
For PF2730 and PF3230 models, OP1 is set to 158, OP7 to 191 and OP8 to 101 when using
TDA9375 or OP1 is set to 190, OP7 to 191 and OP8 to 101 when using TDA9379.

45
SERVICE MANUAL

TROUBLESHOOTING FLOW CHARTS


1.Power On/Off
1.1 The power indicator lights but with no raster and sound

1.2 The SMPS has no voltage output.

46
SERVICE MANUAL

1.3 The SMPS is always in the Standby mode.

2. Control System
2.1 The power indicator lights, but the CPU cannot enter the Operation mode after power-
on again.

2.2 Channel number remains unchanged during auto program.

47
SERVICE MANUAL

3. Video Signal Processor


3.1 No color

3.2 The color is abnormal.

4. Horizontal/Vertical Scan Circuit

4.1 No raster

48
SERVICE MANUAL

4.2 Raster is displayed as a horizontal bright line on the screen.

4.3 The field amplitude of raster is not enough.

4.4 East-west pincushion distortion

49
SERVICE MANUAL

5. Audio System
5.1 No sound but with picture

50
SERVICE MANUAL

6. Video System
6.1 No picture

51
APPENDIX 1: Circuit Diagram for PF2720/PF2730 (1)
APPENDIX 2: Circuit Diagram for PF2720/PF2730 (2)
Note: VM board for PF2730 only
APPENDIX 3: Circuit Diagram for PF3220/PF3230 (1)
APPENDIX 4: Circuit Diagram for PF3220/PF3230 (2)
Note : VM Board for Pf3230 only
APPENDIX 4: Main PCB Layout for PF2720/PF2730/PF3220/PF3230
APPENDIX 6: AV PCB Layout for PF2720/PF2730/PF3220/PF3230
APPENDIX 7: Auxiliary PCBs Layout for PF2720/PF2730/PF3220/PF3230 (3)

CRT RGB PCB


VM PCB

Power PCB
APPENDIX 8: Final Wiring Diagram for PF2720

Remote Sensor PCB Assembly Key PCB Assembly

KK06
TV/AV
KK05
P+
KK04
P-
KK03
MENU
KK02
V+
KK01
V-
Side-set AV PCB Assembly
XPK01

Wired Connector XPK01


XS805
Power Switch PCB Assembly Wired Connector XE03
Speaker

XE03
From power cord
From degaussing coil
CPC01
Speaker
Wired Connector XP205
- + Wired Connector CPC01 - +
Wired Connector XS800

CN801
CN361

CN801 Main PCB Assembly


CN803

CN802
CN804 Cord Plug
Power PCB Assembly
CN207

CN502

CN805 Cord Plug


CN804
To deflection yoke

CN103

CN102
CN101
CN805

CN501

Wired Connector XPY01


XPY03 Cord Plug
Red
White
AV PCB Assembly

Gray GND1

GND2

To CRT's ground binding wire


XPY03

VG2 XPY01

CRT RGB PCB Assembly


APPENDIX 9: Final Wiring Diagram for Pf2730

Remote Sensor PCB Assembly Key PCB Assembly

KK06
TV/AV
KK05
P+
KK04
P-
KK03
MENU
KK02
V+
KK01
V-
Side-set AV PCB Assembly
XPK01

Wired Connector XPK01


XS805
Power Switch PCB Assembly Wired Connector Xe03
Speaker

XE03
CPC01
Speaker

From power cord


From degaussing coil
Wired Connector XP205
- + Wired Connector CPC01 - +
Wired Connector XS800

CN801
CN361

CN801 Main PCB Assembly

Wired Connector CN804


CN803

CN802
Wired Connector VDP03
Power PCB Assembly CN806 From VM PCB's Wired Connector VDP02A (9379 CMOS chip )

Wired Connector CN805


CN502 CN207

CN804
To deflection yoke From VM PCBs Wired Connector VDP02 (9375 CMOS chip )
CN206A
CN206
CN103

CN102
CN101
CN805

Wired Connector XPY03

CN501
VDP04

Red VM PCB Assembly


White

VDP02
VDP03
XPY01 Cord Plug
Gray GND1

GND2

To CRT's Ground Binding Wire AV PCB Assembly


XPY03

VG2 XPY01

CRT RGB PCB Assembly


APPENDIX 10: Exploded View for PF2720/PF2730

3 9
2

1
12

4
10

11

12
8
10

5
13 20
19
18
17
16
15
14
13 plasticene
12 Tapping screw M6X35W 4
11 Tapping screw 4X20BAHCh 6
10 Tapping screw 4X16BTHCh 4
9 Washer 4

11 10 8
7
C-UL label
Real label
1
1
6 Admonition label 1
5 Distance clip 1
7 4 Back cover 1
6 3
2
Front cover assembly
CRT assembly
1
1
1 Chassis assembly 1
Serial
No. Parts Quantity
APPENDIX 11: Final Wiring Diagram for Pf3220

Remote Sensor PCB Assembly Key PCB Assembly

KK06
TV/AV
KK05
P+
KK04
P-
KK03
MENU
KK02
V+
KK01
V-
Side-set AV PCB Assembly
XPK01

Wired Connector XPK01


XS805

Speaker
Power Switch PCB Assembly Wired Connector XE03

XE03
CPC01
Speaker

From power cord


Wired Connector XP205

From degaussing coil


- + Wired Connector CPC01 - +
Wired Connector XS800

Wired Connector CN804

CN801
CN361

CN801 Main PCB Assembly


CN803

CN802
Wired Connector CN805
Power PCB Assembly
CN207

CN502

CN804
To Deflection Yoke

CN103

CN102
CN101
CN805

Wired Connector XPY03


CN501

Red
White

Wired Connector XPY01


AV PCB Assembly

Gray GND1

GND2

To CRT's Ground Wire


XPY03

VG2 XPY01

CRT RGB PCB Assembly


APPENDIX 12: Final Wiring Diagram for Pf3230

Remote Sensor PCB Assembly Key PCB Assembly


KK06
TV/AV
KK05
P+
KK04
P-
KK03
MENU
KK02
V+
KK01
V-
Side-set AV PCB Assembly
XPK01

Wired Connector XPK01


XS805

Speaker
Power Switch PCB Assembly Wired Connector XE03

XE03
Speaker

From power cord


From degaussing coil
CPC01

Wired Connector XP205


- + Wired Connector CPC01 - +
Wired Connector XS800

CN801
CN361

Wired Connector CN804


CN801 Main PCB Assembly
CN803

CN802
Wired Connector VDP03

Wired Connector CN805


Power PCB Assembly CN806 From VM PCBs Wired Connector VDP02A (9379 CMOS chip )

CN502 CN207
CN804
To deflection yoke From VM PCBs Wired Connector VDP02 (9375 CMOS chip )
CN206A
CN206
CN103

CN102
CN101
CN805

Wired Connector XPY03

CN501
VDP04

Wired Connector XPY01


Red VM PCB Assembly
White

VDP02
VDP03
gray GND1

GND2

To CRT's Ground Binding Wire AV PCB Assembly


XPY03

VG2 XPY01

CRT RGB PCB Assembly


APPENDIX 13: Exploded View for PF3220/PF3230

or 20 Soldering agent
19 Tin solder
18 Q04-3 white nitro magnetic paint
17 Tapping screw 4X20BAHCh 8
16 Tapping screw 4X16BTHCh 4
15 C-1 notched washer 8
14 I hexagon nut A and B M8 4
or 13 Washer 8
12 C-UL label 1
11 Real label 1
10 C-UL label 1
9 Real label 1
8 Admonition label 1
7 Admonition label 1
or 6 Distance clip 1
5 Wire clip 2
4 Back cover 1
3 Front cover assembly 1
2 CRT assembly 1
1 Chassis assembly 1
Serial
No. Parts Quantity

Вам также может понравиться