Академический Документы
Профессиональный Документы
Культура Документы
Method of Procedure
Alcatel-Lucent 7356REM ISAM Turn Up Guide
TABLE OF CONTENTS
All rights reserved. Passing on and copying of this document, use and
1 PREFACE ........................................................................................................................................ 5
2 COMPATIBILITY ......................................................................................................................... 5
3 CONVENTIONS ............................................................................................................................ 5
4.1 CONNECT TO THE 7360FX OLT & 7356REM MDU ISAM VIA CRAFT TERMINAL .........................6
5.10 DISABLE PASSWORD AGING & TIMEOUT FOR OPERATOR LOGIN .................................................. 10
6.10 DISABLE PASSWORD AGING & TIMEOUT FOR OPERATOR LOGIN .................................................. 13
8.1 CREATE VECTORING CONTROL ENTITY (VCE) PROFILE AND ASSOCIATE IT TO A BOARD ............... 18
1 Preface
All rights reserved. Passing on and copying of this document, use and
This document describes the process of configuring a 7356REM ISAM for use in PT
Telkom network for the Vectoring Field Trial.
2 Compatibility
This document supports the configuration of the 7356REM ISAM with the following
release:
ISAM R5.0 or higher
3 Conventions
The following conventions are used throughout this document:
Courier New font: denotes to be entered commands, and their output.
Alcatel-Lucent.
4 Pre-configuration steps
All rights reserved. Passing on and copying of this document, use and
4.1 Connect to the 7360FX OLT & 7356REM MDU ISAM via Craft Terminal
Connect the PC’s Serial port to the craft port of the 7356REM ISAM (LCMI). The craft
port is located on the NRNT-A card.
Pin-out of RJ45 connector:
Open HyperTerminal (or equivalent) and setup the serial connection with following
parameters:
Choose ‘C’ to enter the TL1. The factory username and password are:
Username = isadmin
Password = i$@mad-
Note: The system will reset and come up with an empty database. Follow step 4.1 to
re-connect to the system.
Configure 1 uplink to connect to the network, port 1 on NT in 1GE mode for connection
to Metro-E.
isadmin># configure port nt-a:xfp:1 ethernet speed 1000
isadmin># configure port nt-a:xfp:1 ethernet autonegotiate
limited
isadmin># configure port nt-a:xfp:1 no shutdown
Note: The bold part needs to be replaced by the actual value found on the node
information sheet
Note: The bold part needs to be replaced by the actual value found on the node
information sheet
Note: System is now reachable from EMS and the network.
"%s:%n@AR09-TDS-01%d%c"
Note: The bold part needs to be replaced by the actual value found on the node
information sheet
Note: The total length of the prompt string needs to be less or equal than 28
characters. This means the system ID can only be 18 characters.
Note: After setting this slot numbering the operator needs to logout and login again to
activate the new setting
Disable the password aging and session time out for operator login
All rights reserved. Passing on and copying of this document, use and
Note: The bold part needs to be replaced by the actual value found on the node
information sheet
Note: The bold part needs to be replaced by the actual value found on the node
information sheet
Note: The NTP server IP points to the AMS Server
Note: The system will reset and come up with an empty database. Follow step 4.1 to
re-connect to the system.
to OLT.
isadmin># configure interface shub port nt:sfp:1 port-type
network mode 1gbps:full admin-status up
Note: The bold part needs to be replaced by the actual value found on the node
information sheet
Note: The bold part needs to be replaced by the actual value found on the node
information sheet
Note: System is now reachable from EMS and OLT
information sheet
All rights reserved. Passing on and copying of this document, use and
Note: The bold part needs to be replaced by the actual value found on the node
information sheet
Note: The total length of the prompt string needs to be less or equal than 28
Alcatel-Lucent.
Note: After setting this slot numbering the operator needs to logout and login again to
activate the new setting
timeout 300
All rights reserved. Passing on and copying of this document, use and
Note: The bold part needs to be replaced by the actual value found on the node
Alcatel-Lucent.
information sheet
Note: The bold part needs to be replaced by the actual value found on the node
information sheet
Note: The NTP server IP points to the AMS Server
snooping mrouter-port
All rights reserved. Passing on and copying of this document, use and
Note: The bold part needs to be replaced by the actual value found on the node
information sheet.
VoD VLAN:
Multicast VLAN:
isadmin># configure vlan id 110 mode residential-bridge name
IPTV in-qos-prof-name name: Ingress_Default
Alcatel-Lucent.
Note: The bold part needs to be replaced by the actual value found on the node
information sheet.
8.1 Create Vectoring Control Entity (VCE) Profile and associate it to a board
A non-null Vectoring Control Entity (VCE) profile should be associated to a board which
is capable of processing the vectoring algorithms (Board Level Vectoring (BLV) board).
isadmin># configure xdsl vce-profile 1 name VCE_DEFAULT version
1 vce-join-timeout 20 active
isadmin># configure xdsl board 1/1/1 vce-profile 1
isadmin>configure>xdsl>spectrum-profile>1$ dis-g992-1-b
All rights reserved. Passing on and copying of this document, use and
isadmin>configure>xdsl>spectrum-profile>1$ dis-g992-2-a
isadmin>configure>xdsl>spectrum-profile>1$ dis-g992-3-a
isadmin>configure>xdsl>spectrum-profile>1$ dis-g992-3-b
isadmin>configure>xdsl>spectrum-profile>1$ dis-etsi-ts
isadmin>configure>xdsl>spectrum-profile>1$ g993-2-8a
isadmin>configure>xdsl>spectrum-profile>1$ g993-2-8b
isadmin>configure>xdsl>spectrum-profile>1$ g993-2-8c
isadmin>configure>xdsl>spectrum-profile>1$ g993-2-8d
isadmin>configure>xdsl>spectrum-profile>1$ g993-2-12a
Alcatel-Lucent.
isadmin>configure>xdsl>spectrum-profile>1$ g993-2-12b
isadmin>configure>xdsl>spectrum-profile>1$ g993-2-17a
isadmin>configure>xdsl>spectrum-profile>1$ max-noise-down 240
isadmin>configure>xdsl>spectrum-profile>1$ vdsl
isadmin>configure>xdsl>spectrum-profile>1>vdsl# vdsl-band-plan
annex-b-998ade
isadmin>configure>xdsl>spectrum-profile>1>vdsl# optional-band up
isadmin>configure>xdsl>spectrum-profile>1>vdsl# optional-endfreq
138
isadmin>configure>xdsl>spectrum-profile>1>vdsl# adsl-band allow-
adsl
isadmin>configure>xdsl>spectrum-profile>1>vdsl# max-band 8
isadmin>configure>xdsl>spectrum-profile>1>vdsl# pbo-mode pbo-
mode-down
isadmin>configure>xdsl>spectrum-profile>1>vdsl# pbo 1
isadmin>configure>xdsl>spectrum-profile>1>vdsl>pbo>1# param-a
4000
isadmin>configure>xdsl>spectrum-profile>1>vdsl>pbo>1# exit
isadmin>configure>xdsl>spectrum-profile>1>vdsl# pbo 2
isadmin>configure>xdsl>spectrum-profile>1>vdsl>pbo>2# param-a
4730
isadmin>configure>xdsl>spectrum-profile>1>vdsl>pbo>2# param-b
1977
isadmin>configure>xdsl>spectrum-profile>1>vdsl>pbo>2# exit
isadmin>configure>xdsl>spectrum-profile>1>vdsl# pbo 3
isadmin>configure>xdsl>spectrum-profile>1>vdsl>pbo>3# param-a
5400
isadmin>configure>xdsl>spectrum-profile>1>vdsl>pbo>3# param-b
1577
isadmin>configure>xdsl>spectrum-profile>1>vdsl>pbo>3# exit
isadmin>configure>xdsl>spectrum-profile>1>vdsl# pbo 4
5400
All rights reserved. Passing on and copying of this document, use and
isadmin>configure>xdsl>spectrum-profile>1>vdsl>pbo>4# param-b
1077
isadmin>configure>xdsl>spectrum-profile>1>vdsl>pbo>4# exit
isadmin>configure>xdsl>spectrum-profile>1>vdsl# pbo 5
isadmin>configure>xdsl>spectrum-profile>1>vdsl>pbo>5# param-a
5400
isadmin>configure>xdsl>spectrum-profile>1>vdsl>pbo>5# param-b
943
isadmin>configure>xdsl>spectrum-profile>1>vdsl>pbo>5# exit
isadmin>configure>xdsl>spectrum-profile>1>vdsl# exit
Alcatel-Lucent.
isadmin>configure>xdsl>spectrum-profile>1# vdsl2
isadmin>configure>xdsl>spectrum-profile>1>vdsl2# propr-feat-
value 2147483134
isadmin>configure>xdsl>spectrum-profile>1>vdsl2# psd-shape-down
regionbm2-psd-down
isadmin>configure>xdsl>spectrum-profile>1>vdsl2# psd-shape-up
regionbm2-psd-down
isadmin>configure>xdsl>spectrum-profile>1>vdsl2# rx-psd-shape-up
ab-param
isadmin>configure>xdsl>spectrum-profile>1>vdsl2# pbo 1
isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>1# param-a
4000
isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>1# exit
isadmin>configure>xdsl>spectrum-profile>1>vdsl2# pbo 2
isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>2# param-a
4730
isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>2# param-b
1977
isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>2# exit
isadmin>configure>xdsl>spectrum-profile>1>vdsl2# pbo 3
isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>3# param-a
5400
isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>3# param-b
1577
isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>3# exit
isadmin>configure>xdsl>spectrum-profile>1>vdsl2# pbo 4
isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>4# param-a
5400
isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>4# param-b
1077
isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>4# exit
isadmin>configure>xdsl>spectrum-profile>1>vdsl2# pbo 5
5400
All rights reserved. Passing on and copying of this document, use and
isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>5# param-b
943
isadmin>configure>xdsl>spectrum-profile>1>vdsl2>pbo>5# exit
isadmin>configure>xdsl>spectrum-profile>1>vdsl2# exit
isadmin>configure>xdsl>spectrum-profile>1# active
isadmin>configure>xdsl>spectrum-profile>1# exit
Note: The bold part needs to be replaced by the actual value found on the node
information sheet.
VoD VLAN:
isadmin># configure vlan shub id 111 mode residential-bridge
name VoD user2-comm disable
isadmin># configure vlan shub id 111 egress-port lt:1/1/1
isadmin># configure vlan shub id 111 egress-port nt:sfp:1
isadmin># configure vlan id 111 mode residential-bridge name VoD
broadcast-frames
Voice VLAN:
isadmin># configure vlan shub id 2929 mode voice-vlan name SIP
isadmin># configure vlan shub id 2929 egress-port lt:1/1/1
isadmin># configure vlan shub id 2929 egress-port nt:sfp:1
Note: The bold part needs to be replaced by the actual value found on the node
information sheet.
syntax random
All rights reserved. Passing on and copying of this document, use and
Note: The bold part needs to be replaced by the actual value found on the node
information sheet.
- END OF DOCUMENT -