Академический Документы
Профессиональный Документы
Культура Документы
2:1 mix with BODY PRO H 725 HARDENER FOR PRIMERS Non force dry
Pot life: 45 - 50 min @ 23°C (73°F) 100-120 micron
2 - 3h / 23°C (73°F)
20 - 30 min / 60°C (140°F) panel temperature
IR 10 – 15 min
No Thinner Addition distance 60-70 cm
P 320 - P 500
Flat bed sander
Ready to spray:
22-26 s
DIN 4 @ 20°C (68°C)
P 600 – P 800
Sanding by hand, wet
2K paint systems tend to react with water, hence all the equipment used must be moisture free. Isocyanates may cause skin sensitization. More specifically,
care should be taken when handling the material. Anyone with a history of histaminic conditions, or respiratory problems should consult the doctor first.
For professional use only. The information displayed on this sheet has been carefully selected through a series of laboratory investigations. It is based on our best
knowledge at the time of issue. The data is given for information purposes only. We are not liable for its correctness, accuracy and completeness. It is up to the
user to check for newer updates or further information if needed for his intended purpose. The intellectual property of this product, trademarks and copyrights
is protected. All rights reserved. The relevant Material Safety Data Sheet and warnings displayed on the label must be read carefully. We may modify and / or
discontinue operation of all or portions of this information at any time in our sole discretion, without any notice and assume no responsibility to update the
information. All rules set forth in this clause shall apply accordingly for any future changes and amendments.
Product Application: Applied direct on plastic bumpers (PE - PP - ABS - TSOP etc.)
1 - 3 coats »» Apply 1 - 3 light coats.
2K paint systems tend to react with water, hence all the equipment used must be moisture free. Isocyanates may cause skin sensitization. More specifically,
care should be taken when handling the material. Anyone with a history of histaminic conditions, or respiratory problems should consult the doctor first.
For professional use only. The information displayed on this sheet has been carefully selected through a series of laboratory investigations. It is based on our
best knowledge at the time of issue. The data is given for information purposes only. We are not liable for its correctness, accuracy and completeness. It is up to
the user to check for newer updates or further information if needed for his intended purpose. The intellectual property of this product, trademarks and copy-
rights is protected. All rights reserved. The relevant Material Safety Data Sheet and warnings displayed on the label must be read carefully. We may modify and
/ or discontinue operation of all or portions of this information at any time in our sole discretion, without any notice and assume no responsibility to update the
information. All rules set forth in this clause shall apply accordingly for any future changes and amendments.
2:1 mix with BODY 720 2K Autoemail Acrylic Flash Point: Remarks:
NORMAL HARDENER Paint SR 25°C / 77°F • Allow for additional time for
Pot life: 45min HB BODY Basecoat combi spray booths to reach the
@23°C (73°F) HB BODY UHS Clears Specific Gravity: desired temperature
1.35 g/cm3 • Application only with the
Addition 50 - 60% recommended hardeners and
Always wear Solid Content (No thinner): solvents
of thinner
protective equipment 71% Weight
Use BODY 740 NORMAL • It can be used by countries
ACRYLIC THINNER that do not adopt the VOC
VOC (2004/42/EC)
or BODY 741 SLOW legislation as well.
This product is a special refinish
ACRYLIC THINNER
product based on its ingredients • Do not use at temperatures
Follow the application and its properties. The maximum below 15°C (59°F).
instructions mentioned VOC content in this category
Ready to spray: • Do not apply the primer as
in this TDS is 540 g/L. The VOC content in
14-15 s ‘wet on wet’ on TPA surfaces
the ready for use form of this
DIN 4 @ 20°C
Notes: product is 470 g/L.
2004/42/IIB(c)(540)470 Caution:
A. On a “wet on wet” application Always check with a cloth and
Compliant Spray gun 720 hardener must be used (never thinner if the panel is an OEM
1.3mm – 1.4mm H 725). Theoretical Coverage:
(E-COAT) panel. On OEM
3-4 bar inlet pressure 10 m2 / l at 80 micron dry film
B. Never apply “wet on wet” thickness
(E-COAT) panels, the cloth stays
1-2 coats = 20-30 μm over polyester fillers due to the clean. Then clean the surface
fact that can be seen after clear with #770 ANTISIL and the “wet
Cleaning of equipment:
coating. on wet” procedure is followed
HVLP 1.3mm-1.4mm Clean after final use with
without sanding prior to primer
2 bar atomization Body 740 ACRYL NORMAL
application.
pressure
1-2 coats = 20-30 μm Storage Shelf life:
• Store in a cool place (+5 to 25°C)
and use within 12 months for
15-20 min / 23°C (73°F) best results.
Final flash off time Guaranteed shelf life of 24
months in unused original
containers
2K paint systems tend to react with water, hence all the equipment used must be moisture free. Isocyanates may cause skin sensitization. More specifically,
care should be taken when handling the material. Anyone with a history of histaminic conditions, or respiratory problems should consult the doctor first.
For professional use only. The information displayed on this sheet has been carefully selected through a series of laboratory investigations. It is based on our
best knowledge at the time of issue. The data is given for information purposes only. We are not liable for its correctness, accuracy and completeness. It is up to
the user to check for newer updates or further information if needed for his intended purpose. The intellectual property of this product, trademarks and copy-
rights is protected. All rights reserved. The relevant Material Safety Data Sheet and warnings displayed on the label must be read carefully. We may modify and
/ or discontinue operation of all or portions of this information at any time in our sole discretion, without any notice and assume no responsibility to update the
information. All rules set forth in this clause shall apply accordingly for any future changes and amendments.