Академический Документы
Профессиональный Документы
Культура Документы
Product Guide
Features
• 50 t or 55 t (50 USt or 60 USt) capacity
MEGAFORMTM boom
The 11 m – 33,5 m (36 ft – 110 ft)
four-section full power sequenced
synchronized MEGAFORM™ boom
is designed for maximum vertical and
lateral strength.
Suspension system
Standard front and rear air ride suspension
provides a comfortable ride at maximum speed
of 105 km/h (65 mph).
Cummins diesel
carrier engine
Cummins ISX 12 diesel carrier
engine delivers the horsepower
and torque needed to negotiate
tough job sites and achieve
highway travel speeds.
Contents
Specifications 4
Dimensions 7
Travel proposals 8
Working range 9
Load handling 21
Symbols glossary 38
Specifications
Superstructure
Cab
Maximum permissible line pull: 7620 kg (16,800 lb) Cummins QSM 11 six-cylinder, turbo-charged and
with standard 6 x 37 after-cooled diesel engine. 10.8 L (660 in3), 300 kW
class rope (402 bhp) at 1800 rpm. Maximum torque 1898 Nm
(1400 lb-ft) at 1400 rpm. Tier III “Off-Highway” EPA,
CARB and EU Stage IIIA compliant.
7620 kg (16,800 lb)
with optional 35 x 7 Equipped with engine compression brake, audio-visual
class rope engine distress system and ether cold start aid.
Rope diameter: 19 mm (.75 in) Fuel Requirement: Maximum of 5000 ppm sulfur
content.
Rope length: 152 m (500 ft)
Fuel tank capacity
Maximum rope stowage: 256 m (841 ft)
379 L (100 gal).
Carrier
Transmission
Chassis
Roadranger 11 speeds forward, 3 reverse, manual.
Triple box section, four-axle carrier, fabricated
from high strength, low alloy steel with towing and
tie-down lugs. Drive
Drive 8 x 4 x 4.
Outrigger system
Outrigger controls Rear: (2) single reduction drive axles, 1,9 m (75.1 in)
track. Inter-axle differential lock.
Located in the superstructure cab and both sides of
chassis. Level indicator at each control station.
Electrical system
Maximum speed
4262 mm
(13' 11.78")
2591 mm 4102 mm (161.5")
MID
(8' 6.00") 28° 14 046 mm TURNING TAILSWING
1891 mm EXTENDED
(46'-1.00") RADIUS (6' 2.45")
REAR 6096 mm
TRACK (20' 00")
2429 mm FULLY
4262 mm
(7' 11.62") EXTENDED
2591 mm FULLY (13' 11.78")
16 916 mm (55'-6.00")
(8' 6.00") 1295 mm RETRACTED MID
CLEARANCE 1891 mm EXTENDED
RADIUS (4' 3.00") (6' 2.45")
REAR 6096 mm
TRACK (20' 00")
2429 mm FULLY
2079 mm (7' 11.62") EXTENDED
(6' 9.84") 32° FULLY
16 916 mm (55'-6.00") 1295 mm FRONT TRACK 9449 mm (31' 0") RETRACTED
CLEARANCE MIN RADIUS
RADIUS (4' 3.00")
2079 mm
(6' 9.84") 32°
FRONT TRACK 9449 mm (31' 0")
MIN RADIUS
4102 mm
(13' 5.50")
10 950 mm (35' 11" ) RETRACTED
33 530 mm(110' 0") EXTENDED
C
L ROTATION
13 557 mm (44' 5.75")
4102 mm
3586 mm (13' 5.50")
(11' 9.18") 10 950 mm (35' 11" ) RETRACTED
33 530 mm(110' 0") EXTENDED
C
L ROTATION
3454 mm
3586 mm (11' 4")
(11' 9.18") 1759 mm
(5' 9.25") 555 mm
(1' 9.85")
496 mm (1' 7.52") 301 mm
(11.87")
2106 mm 3454 mm
(6' 10.92") (11' 4")
1759 mm 18°
(5' 9.25")17° 555 mm
(1' 9.85")
496 mm (1' 7.52") 301 mm
1524 mm (11.87")
2106 mm (5'.00")
4013 mm 2489 mm 1524 mm 533 mm 254 mm
(6' 10.92") 635 mm (13' 2.00) (8' 2.00") (5' 0.00") (1' 9") (10.00") 18°
17° (2' 1.00") 5639 mm
(18' 6.00")
3099 mm
(10' 2.00")
11 147 mm 1524 mm
(36' 6.87") (5'.00")
4013 mm 2489 mm 1524 mm 533 mm 254 mm
635 mm (13' 2.00) (8' 2.00") (5' 0.00") (1' 9") (10.00")
(2' 1.00") 5639 mm
(18' 6.00")
3099 mm
(10' 2.00")
11 147 mm
(36' 6.87")
1
Counterweight Configurat
Zero
5,500 lb. (2 495 k g.)
11,000 lb. ( 4 990 kg.)
1. 2495 kg (5500 lb) 16,500 lb. (7 485 k g.)
2. 2495 kg (5500 lb)
1 2 3
Counterweight configuration Load Chart Configuration - 360•
Zero
16,500 lb. 11,000 lb. 5,500 lb. 0 lb.
2495 kg (5500 lb)
Main
4990 boom
kg (11,000 lb)
X X X X
33kgf (16,500
7485 t. Swingaw
lb) ay X X X X
56 ft. Swingaway X X X X
Grove TMS700E 76 f t. Boomextension 7
(56 ft.+ 20 ft. insert) X X X X
Travel proposals
5639 mm
(18.5')
1524 mm 1524 mm
(5') (5')
17 556 mm
(57.6')
5639 mm
(18.5')
1524 mm 1524 mm 1372 mm
(5') (5') 3962 mm (4.5')
(13')
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
8 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Working range
180
56' EXT
170
160
33' EXT
150
140
130
110
120 70°
60° 100
110
50° 90
100
90
40°
70
80
60
70 30°
50
60
20° 40
50
36
40
30
10° 78°
Max.
Boom
Angle
20
10 0°
0
160 150 140 130 120 110 100 90 80 70 60 50 40 30 20 10 0
AXIS OF
ROTATION
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
Grove TMS700E The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. 9
TMS760E load charts
Boom Counterweight Outriggers Rotation
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
10 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Load chart
NOTES:
36 ft – 110 ft 33 ft – 56 ft 16,500 lb 100% 360° 1. All capacities above the bold line are based
20 ft on structural strength of boom extension.
Pounds 2. 33 ft and 56 ft boom extension lengths may
60 10,100 8550 6800 7540 5140 heavier loads than the capacities listed is
(66) (70.5) (72.5) (71) (77)
strictly prohibited. Machine tipping with
65 9130 7930 6650 7160 5100 *3860
(63.5) (68) (70.5) (69) (75) (78) boom extension occurs rapidly and without
70 8460 7380 6490 6820 5100 3790
(61.5) (65.5) (68) (67.5) (73) (77.5) advance warning.
7840 6900 6370 6300 4800 3660 5. Boom angle is the angle above or below
75
(59) (63) (65.5) (65.5) (71) (75)
horizontal of the longitudinal axis of the
80 7230 6470 6110 5810 4580 3550
(56.5) (60.5) (62.5) (63.5) (69) (73) boom base section after lifting rated load.
6470 6070 5780 5370 4470 3450
85 6. Capacities listed are with outriggers properly
(54) (58) (60) (61.5) (67.5) (71)
5670 5720 5480 4980 4330 3410 extended and vertical jacks set only.
90
(51) (55.5) (57) (59.5) (65.5) (68.5)
4970 5400 5200 4630 4070 3300
95
(48.5) (52.5) (54) (57) (63) (66.5)
4350 4840 4950 4320 3830 3260
100
(45.5) (49.5) (51) (55) (61) (64)
3790 4210 4470 4040 3620 3220
105
(42.5) (46.5) (47.5) (52.5) (58.5) (62)
3290 3640 3760 3410 3180
110
(39.5) (43) (50.5) (56) (59.5)
2830 3130 3290 3230 3060
115
(36) (39.5) (48) (53.5) (56.5)
2420 2660 2860 3050 2940
120
(32) (35) (45.5) (51) (53.5)
2040 2240 2470 2890 2800
125
(27.5) (30.5) (42.5) (48.5) (50.5)
1700 2120 2590
130
(22) (39.5) (45.5)
1790 2200
135
(36.5) (42.5)
1480 1840
140
(33) (38.5)
1200 1500
145
(29.5) (34.5)
No load stability data
Min. boom
angle for
indicated 21° 25° 45° 28° 28° 45°
length
Max. boom
length at 0° 100 ft 90 ft
boom angle
NOTE: ( ) Boom angles are in degrees. A6-829-101337
*This capacity is based upon maximum boom angle.
#LMI operating code. Refer to LMI manual for instructions.
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
Grove TMS700E The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. 11
TMS760E load charts
Boom Counterweight Outriggers Rotation
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
12 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Load chart
NOTES:
36 ft – 110 ft 33 ft– 56 ft 11,000 lb 100% 360° 1. All capacities above the bold line are based
20 ft on structural strength of boom extension.
Pounds 2. 33 ft and 56 ft boom extension lengths may
33 ft length 56 ft length be used for single line lifting service.
#0121 #0122 #0123 #0141 #0142 #0143 3. Radii listed are for a fully extended boom
Feet 0° 25° 45° 0° 25° 45°
with the boom extension erected. For main
Offset Offset Offset Offset Offset Offset
12,900 boom lengths less than fully extended, the
30 (78)
rated loads are determined by boom angle.
35 12,900 *8330
(76) (78) Use only the column which corresponds to
40 12,900 *10,850 8330
(74) (78) (77.5) the boom extension length and offset for
45 12,900 10,450 *7410 8330 which the machine is configured. For boom
(72) (77) (78) (76)
angles not shown, use the rating of the next
50 12,100 10,000 7200 8330
(70) (74.5) (77.5) (74.5) lower boom angle.
55 11,100 9220 6990 8250 *5300
(68) (72.5) (75) (73) (78) 4. WARNING: Operation of this machine with
60 10,100 8550 6800 7540 5140 heavier loads than the capacities listed is
(66) (70.5) (72.5) (71) (77)
9130 7930 6650 7160 5100 *3860 strictly prohibited. Machine tipping with
65 (63.5) (68) (70.5) (69) (75) (78) boom extension occurs rapidly and without
70 7960 7380 6490 6820 5100 3790
(61.5) (65.5) (68) (67.5) (73) (77.5) advance warning.
75 6870 6900 6370 6300 4800 3660 5. Boom angle is the angle above or below
(59) (63) (65.5) (65.5) (71) (75)
5930 6470 6110 5810 4580 3550 horizontal of the longitudinal axis of the
80 (56.5) (60.5) (62.5) (63.5) (69) (73) boom base section after lifting rated load.
85 5120 5880 5780 5370 4470 3450
(54) (58) (60) (61.5) (67.5) (71) 6. Capacities listed are with outriggers properly
90 4410 5070 5440 4960 4330 3410 extended and vertical jacks set only.
(51) (55.5) (57) (59.5) (65.5) (68.5)
95 3780 4350 4680 4310 4070 3300
(48.5) (52.5) (54) (57) (63) (66.5)
100 3230 3710 4010 3730 3830 3260
(45.5) (49.5) (51) (55) (61) (64)
105 2730 3140 3410 3210 3620 3220
(42.5) (46.5) (47.5) (52.5) (58.5) (62)
110 2280 2630 2750 3410 3180
(39.5) (43) (50.5) (56) (59.5)
115 1870 2170 2330 3020 3060
(36) (39.5) (48) (53.5) (56.5)
120 1500 1750 1940 2550 2800
(32) (35) (45.5) (51) (53.5)
125 1170 1360 1590 2130 2330
(27.5) (30.5) (42.5) (48.5) (50.5)
130 1270 1740
(39.5) (45.5)
135 1390
(42.5)
140 1060
(38.5)
No load stability data
Min. boom
angle for 25° 25° 45° 33° 36° 45°
indicated
length
Max. boom
length at 0° 90 ft 80 ft
boom angle
NOTE: ( ) Boom angles are in degrees. A6-829-101338
*This capacity is based upon maximum boom angle.
#LMI operating code. Refer to LMI manual for instructions.
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
Grove TMS700E The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. 13
TMS760E load charts
Boom Counterweight Outriggers Rotation
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
14 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Load chart
NOTES:
36 ft – 110 ft 33 ft – 56 ft 5500 lb 100% 360° 1. All capacities above the bold line are based
20 ft on structural strength of boom extension.
Pounds 2. 33 ft and 56 ft boom extension lengths may
33 ft length 56 ft length be used for single line lifting service.
#0221 #0222 #0223 #0241 #0242 #0243 3. Radii listed are for a fully extended boom
Feet 0° 25° 45° 0° 25° 45°
Offset Offset Offset Offset Offset Offset with the boom extension erected. For main
12,900 boom lengths less than fully extended, the
30 (78)
rated loads are determined by boom angle.
35 12,900 *8330
(76) (78) Use only the column which corresponds to
40 12,900 *10,850 8330
(74) (78) (77.5) the boom extension length and offset for
45 12,900 10,450 *7410 8330 which the machine is configured. For boom
(72) (77) (78) (76)
12,100 10,000 7200 8330 angles not shown, use the rating of the next
50 (70) (74.5) (77.5) (74.5) lower boom angle.
55 10,450 9220 6990 8250 *5300
(68) (72.5) (75) (73) (78) 4. WARNING: Operation of this machine with
60 8780 8550 6800 7540 5140 heavier loads than the capacities listed is
(66) (70.5) (72.5) (71) (77)
7420 7930 6650 7160 5100 *3860 strictly prohibited. Machine tipping with
65 (63.5) (68) (70.5) (69) (75) (78)
boom extension occurs rapidly and without
70 6280 7260 6490 6820 5100 3790
(61.5) (65.5) (68) (67.5) (73) (77.5) advance warning.
75 5310 6180 6370 6030 4800 3660 5. Boom angle is the angle above or below
(59) (63) (65.5) (65.5) (71) (75)
4490 5250 5840 5150 4580 3550 horizontal of the longitudinal axis of the
80
(56.5) (60.5) (62.5) (63.5) (69) (73)
boom base section after lifting rated load.
85 3770 4450 4950 4400 4470 3450
(54) (58) (60) (61.5) (67.5) (71) 6. Capacities listed are with outriggers properly
90 3150 3750 4180 3730 4330 3410
(51) (55.5) (57) (59.5) (65.5) (68.5) extended and vertical jacks set only.
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
Grove TMS700E The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. 15
TMS760E load charts
Boom Counterweight Outriggers Rotation
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
16 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Load chart
NOTES:
36 ft – 110 ft 33 ft – 56 ft 0 lb 100% 360° 1. All capacities above the bold line are based
20 ft on structural strength of boom extension.
Pounds 2. 33 ft and 56 ft boom extension lengths may
33 ft length 56 ft length be used for single line lifting service.
#0821 #0822 #0823 #0841 #0842 #0843 3. Radii listed are for a fully extended boom
Feet 0° 25° 45° 0° 25° 45°
Offset Offset Offset Offset Offset Offset with the boom extension erected. For main
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
Grove TMS700E The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. 17
Working range
36 ft – 110 ft main boom and 33 ft – 56 ft lattice extension with 40 ft insert
45°
200
33' EXT.
190
180
170
160
150
140
130
120 70°
60° 100
110
50° 90
100
80
90
40°
70
80
60
70 30°
50
60
20° 40
50
36
40
10° 78°
30 Max.
Boom
Angle
20
0°
10
0
200 190 180 170 160 150 140 130 120 110 100 90 80 70 60 50 40 30 20 10 0
AXIS OF
ROTATION
OPERATING RADIUS IN FEET FROM AXIS OF ROTATION
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
18 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Load chart
NOTES:
36 ft – 110 ft 33 ft – 56 ft 20 ft 16,500 lb 100% 360° 1. All capacities above the bold line are based
20 ft on structural strength of boom extension.
Pounds 2. 33 ft and 56 ft boom extension lengths may
33 ft length 56 ft length be used for single line lifting service.
#0064 #0065 #0066 #0084 #0085 #0086 3. Radii listed are for a fully extended boom
Feet 0° 25° 45° 0° 25° 45°
with the boom extension erected. For main
Offset Offset Offset Offset Offset Offset
*9360 boom lengths less than fully extended, the
35 (78)
rated loads are determined by boom angle.
40 9360 *6300
(77.5) (78) Use only the column which corresponds to
8480 *7480 6300
45 (76) (78) (77.5) the boom extension length and offset for
7680 7070 6000 which the machine is configured. For boom
50 (74) (77.5) (77)
angles not shown, use the rating of the next
55 6990 6470 5880 5990
(72) (76) (78) (75.5) lower boom angle.
60 6390 5970 5480 5980 *4840
(70) (74) (76.5) (73.5) (78) 4. WARNING: Operation of this machine with
5890 5570 5080 5510 4840 heavier loads than the capacities listed is
65 (68.5) (72.5) (74.5) (72) (77.5)
strictly prohibited. Machine tipping with
70 5390 5070 4780 5010 4440
(66.5) (70.5) (72.5) (70.5) (76.5) boom extension occurs rapidly and without
75 4990 4770 4480 4560 4050 *3760
(64.5) (68.5) (70.5) (68.5) (75) (78) advance warning.
4650 4400 4190 4170 3870 3460 5. Boom angle is the angle above or below
80 (62.5) (66) (68) (67) (73) (77)
4300 4150 3890 3820 3570 3260 horizontal of the longitudinal axis of the
85 (60) (64) (66) (65) (71.5) (75) boom base section after lifting rated load.
90 4000 3850 3690 3520 3320 2960
(58) (62) (63.5) (63.5) (69.5) (73) 6. Capacities listed are with outriggers properly
95 3760 3650 3500 3220 3070 2770 extended and vertical jacks set only.
(56) (59.5) (61.5) (61.5) (67.5) (71)
100 3510 3410 3300 2980 2880 2570
(53.5) (57.5) (59) (59.5) (66) (69)
105 3260 3210 3100 2780 2680 2460
(51) (55) (56.5) (58) (64) (67)
110 3070 3020 2930 2530 2480 2340
(48.5) (52.5) (54) (56) (62) (65)
115 2870 2870 2780 2340 2280 2200
(46) (50) (51) (54) (60) (63)
120 2550 2730 2190 2140 2050
(43.5) (47) (52) (57.5) (60.5)
125 2170 2500 2000 1990 1910
(40.5) (44) (49.5) (55.5) (58)
130 1820 2100 1850 1850 1810
(37.5) (41) (47.5) (53) (55.5)
1500 1730 1720 1750 1670
135 (34.5) (37.5) (45) (51) (53)
140 1210 1390 1480 1610
(30.5) (33.5) (42.5) (48.5)
145 1520
(45.5)
150 1370
(43)
No load stability data
Min. boom
angle at 110 ft 22° 29° 45° 38° 40° 45°
boom length
Max. boom
length at 0o 100 ft 80 ft
boom angle
NOTE: ( ) Boom angles are in degrees. A6-829-101484
*This capacity is based upon maximum boom angle.
#LMI operating code. Refer to LMI manual for instructions.
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
Grove TMS700E The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. 19
Load chart
NOTES:
36 ft – 110 ft 33 ft – 56 ft 40 ft 16,500 lb 100% 360° 1. All capacities above the bold line are based on
20 ft structural strength of boom extension.
Pounds 2. 33 ft and 56 ft boom extension lengths may be
33 ft Length 56 ft Length used for single line lifting service.
#0064 #0065 #0066 #0084 #0085 #0086 3. Radii listed are for a fully extended boom with
Feet 0° 25° 45° 0° 25° 45°
the boom extension erected. For main boom
Offset Offset Offset Offset Offset Offset
45 6560 lengths less than fully extended, the rated
(78)
loads are determined by boom angle. Use
5960 4510
50 (76) (78) only the column which corresponds to the
55 5360 5860 4210
(74.5) (78) (77.5) boom extension length and offset for which
60 4860 5260 *5170 3910 the machine is configured. For boom angles
(73) (76.5) (78) (76)
4370 4870 4670 3710 not shown, use the rating of the next lower
65 (71) (75) (77.5) (74.5) boom angle.
3970 4370 4270 3410 *3710
70 (69.5) (73) (75.5) (73) (78) 4. WARNING: Operation of this machine with
75 3670 4070 3980 3220 3420 heavier loads than the capacities listed is
(67.5) (71.5) (73.5) (71.5) (77.5)
3270 3670 3680 2820 3120 strictly prohibited. Machine tipping with
80
(66) (69.5) (72) (70) (76)
boom extension occurs rapidly and without
2980 3370 3380 2520 2820 2730
85 (64) (68) (70) (68.5) (74.5) (77.5) advance warning.
90 2780 3080 3080 2320 2620 2530
(62.5) (66) (68) (66.5) (72.5) (76) 5. Boom angle is the angle above or below
95 2480 2880 2890 2030 2330 2340 horizontal of the longitudinal axis of the
(60.5) (64) (66) (65) (71) (74.5)
2290 2580 2690 1830 2130 2140 boom base section after lifting rated load.
100
(58.5) (62) (64) (63.5) (69.5) (72.5) 6. Capacities listed are with outriggers properly
2090 2390 2390 1630 1930 1940
105 (56.5) (60) (62) (62) (68) (71) extended and vertical jacks set only.
110 1900 2190 2200 1440 1730 1740
(54.5) (58) (60) (60) (66) (69)
115 1700 2000 2100 1240 1540 1550
(52.5) (56) (58) (58.5) (64.5) (67)
120 1600 1800 1910 1140 1340 1450
(50.5) (54) (55.5) (57) (62.5) (65)
1410 1700 1710 1240 1260
125 (48) (51.5) (53) (61) (63.5)
130 1310 1510 1520 1050 1160
(46) (49.5) (50.5) (59) (61.5)
135 1120 1420 1420
(43.5) (47) (48)
1030 1220
140 (41) (44.5)
1070
145 (41.5)
No load stability data
Min. boom
angle at 40o 40° 47° 56° 58° 60°
110 ft boom
length
Max. boom
length at 0o 70 ft 40 ft
boom angle
NOTE: ( ) Boom angles are in degrees. A6-829-101494
*This capacity is based upon maximum boom angle.
#LMI operating code. Refer to LMI manual for instructions.
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
20 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Load handling
Weight reductions for load handling devices Line pulls and reeving information
Hoists Cable/Specs. Permissible Nominal
11 m - 33,5 m (33 ft-56 ft) folding boom extension line pulls cable
length
*11 m (33 ft) extension (erected) 1973 kg (4350 lb)
*33,5 m (56 ft) extension (erected) 4286 kg (9450 lb) Main 19 mm (3/4 in) 6x37 Class, 7620 kg 152,4 m
EIPS, IWRC Special Flexible (16,800 lb) (500 ft)
Folding ext. with 20 ft insert Min. breaking strength
26 671 kg (58,800 lb)
*11 m (33 ft) extension (erected) 4268 kg (9410 lb)
*33,5 m (56 ft) extension (erected) 7262 kg (16,010 lb)
Main 19 mm (.75 in) Class 7620 kg 152,4 m
Folding ext. with 40 ft insert and 35x7, Rotation Resistant (16,800 lb) (500 ft)
Auxiliary (non-rotating)
*11 m (33 ft) extension (erected) 7384 kg (16,280 lb) Min. breaking strength
*33,5 m (56 ft) extension (erected) 11 063 kg (24,390 lb) 38 918 kg (85,800 lb)
*Reduction of main boom capacities The approximate weight of 19 mm (3/4 in) wire rope is 1.5 lb /ft
(no deduct required for stowed boom extension)
Hoist performance
When lifting over swingaway and/or jib combinations, deduct Wire Hoist line pulls Drum rope
total weight of all load handling devices reeved over main boom Rope Two speed hoist Capacity m (ft)
nose directly from swingaway or jib capacity.
Layer Low Available High Available Layer Total
Auxiliary boom nose 62 kg (137 lb) kg (lb)* kg (lb)*
7,4 t (8.3 Ust) Headache ball (non-swivel) 159 kg + (350 lb +) 4 6508 kg 3254 kg 39,3 m 140,2 m
(14,347 lb) (7174 lb) (129 ft) (460 ft)
7,4 t (8.3 Ust) Headache ball (swivel) 169 kg + (370 lb +)
5 6084 kg 3042 kg 42,4 m 182,6 m
(13,413 lb) (6707 lb) (139 ft) (599 ft)
+ Refer to rating plate for actual weight.
6 5713 kg 2856 kg 45,4 m 228,0 m
NOTE: All load handling devices and boom attachments (12,594 lb) (6297 lb) (149 ft) (758 ft)
are considered part of the load and suitable allowances
*Maximum lifting capacity: 6x37 or 35x7 class = 7620 kg (16,800 lb)
MUST BE MADE for their combined weights. Weights are for
Grove furnished equipment.
Bold lines determine the limiting position of any load for operation within working areas indicated.
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
Grove TMS700E The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. 21
Working range
Metric 85%
38
33,5
36 70°
34 60° 30,5
32
50° 27,4
30
28 24,4
26 40°
21,3
24
22 30° 18,4
20
15,2
18
16 20° 12,2
14 10,8
12
10 10°
78° Max
8
boom angle
6
4 0°
2
0
50 46 42 38 34 30 26 22 18 14 10 6 0
AXIS OF
48 44 40 36 32 28 26 20 16 12 8 4
ROTATION
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
22 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Load chart
Metric 85%
100%
11 m - 33,5 m 7485 kg 360°
6,1 m
#0001
Radius
in Main boom length in meters
meters
10,8 12,2 15,2 **18,4 21,3 24,4 27,4 30,5 33,5
55 000 38 275 36 375 *28 350
3
(69) (72) (76) (78)
47 400 38 275 36 375 28 350 *16 675
3,5
(66,5) (69,5) (74) (77,5) (78)
43 200 37 975 36 375 28 075 16 675
4
(63,5) (67) (72) (76) (77,5)
40 050 37 550 36 375 27 700 16 675 *16 675
4,5
(60) (64) (70) (74) (76,5) (78)
37 150 35 250 34 350 26 350 16 675 16 675 *14 050
5
(57) (61,5) (68) (72,5) (75,5) (77,5) (78)
31 450 29 950 29 600 23 250 16 675 16 675 14 050 *13 200
6
(50) (55,5) (64) (69) (72,5) (75) (77) (78)
27 475 26 200 25 675 20 575 16 675 15 925 13 775 12 625 *10 875
7
(42) (49) (59,5) (65,5) (69,5) (72,5) (75) (77) (78)
22 050 22 725 22 175 18 525 16 300 14 850 13 075 11 925 10 650
8
(32) (42) (54,5) (62) (66,5) (70) (73) (75) (77)
13 725 18 375 18 075 17 375 15 275 13 350 11 650 11 075 10 050
9
(16) (33) (49,5) (58,5) (63,5) (67,5) (70,5) (73) (75)
13 975 14 950 14 525 13 875 12 075 10 675 10 350 9465
10
(20,5) (44) (54,5) (60,5) (65) (68,5) (71) (73)
10 775 10 325 10 625 10 125 9275 8770 8475
12
(30) (45,5) (53,5) (59,5) (63,5) (67) (69,5)
See 7635 7965 8280 7910 7735 7735
14
Note 16 (35) (46) (53,5) (58,5) (62,5) (65,5)
5745 6110 6450 6770 6825 6825
16
(19,5) (37,5) (47) (53,5) (58) (62)
4730 5100 5430 5625 5695
18
(26) (39,5) (47,5) (53,5) (57,5)
4045 4405 4575 4715
20
(30,5) (41) (48) (53,5)
3215 3575 3750 3845
22
(16,5) (35,5) (42,5) (48,5)
2905 3060 3130
24
(24) (36) (43,5)
2495 2605
26
(28) (38)
2015 2140
28
(16) (31)
1725
30
(22,5)
Minimum boom angle (deg.) for indicated length (no load) 0
Maximum boom length (m) at 0 degree boom angle (no load) 3 3 ,5
NOTE: ( ) Boom angles are in degrees.
#LMI operating code. Refer to LMI manual for instructions.
*This capacity is based on maximum boom angle.
Lifting capacities at zero degree boom angle
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
Grove TMS700E The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. 23
Load chart
Metric 85%
100%
11 m - 33,5 m 7485 kg Over rear
6,1 m
#0001
Radius
in Main boom length in meters
meters
10,8 12,2 15,2 **18,4 21,3 24,4 27,4 30,5 33,5
55 000 38 275 36 375 *28 350
3
(69) (72) (76) (78)
47 400 38 275 36 375 28 350 *16 675
3,5
(66,5) (69,5) (74) (77,5) (78)
43 200 37 975 36 375 28 075 16 675
4
(63,5) (67) (72) (76) (77,5)
40 050 37 550 36 375 27 700 16 675 *16 675
4,5
(60) (64) (70) (74) (76,5) (78)
37 150 35 250 34 350 26 350 16 675 16 675 *14 050
5
(57) (61,5) (68) (72,5) (75,5) (77,5) (78)
31 450 29 950 29 600 23 250 16 675 16 675 14 050 *13 200
6
(50) (55,5) (64) (69) (72,5) (75) (77) (78)
27 475 26 200 25 675 20 575 16 675 15 925 13 775 12 625 *10 875
7
(42) (49) (59,5) (65,5) (69,5) (72,5) (75) (77) (78)
22 050 22 925 22 175 18 525 16 300 14 850 13 075 11 925 10 650
8
(32) (42) (54,5) (62) (66,5) (70) (73) (75) (77)
13 725 20 375 18 475 17 375 15 275 13 350 11 650 11 075 10 050
9
(16) (33) (49,5) (58,5) (63,5) (67,5) (70,5) (73) (75)
13 975 16 125 15 125 13 875 12 075 10 675 10 350 9465
10
(20,5) (44) (54,5) (60,5) (65) (68,5) (71) (73)
12 175 11 800 10 975 10 125 9275 8770 8475
12
(30) (45,5) (53,5) (59,5) (63,5) (67) (69,5)
See 8885 8690 8330 7910 7735 7735
14
Note 16 (35) (46) (53,5) (58,5) (62,5) (65,5)
6630 7195 7065 6825 6825 6825
16
(19,5) (37,5) (47) (53,5) (58) (62)
6080 5965 5695 5695 5695
18
(26) (39,5) (47,5) (53,5) (57,5)
5115 4830 4715 4715
20
(30,5) (41) (48) (53,5)
4035 4055 3845 3845
22
(16,5) (35,5) (42,5) (48,5)
3370 3130 3130
24
(24) (36) (43,5)
2605 2605
26
(28) (38)
2220 2170
28
(16) (31)
1840
30
(22,5)
Minimum boom angle (de g.) for indicated le ngth (no load) 0
Maximum boom length (m) at 0 de gree boom angle (no load) 3 3 ,5
NOTE: ( ) Boom angles are in degrees.
#LMI operating code. Refer to LMI manual for instructions.
*This capacity is based on maximum boom angle.
Lifting capacities at zero degree boom angle
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
24 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Load chart
Metric 85%
NOTES:
100%
11 m - 33,5 m 10,1 m - 17 m 7485 kg 360°
6,1 m 1. All capacities above the bold line are based on
structural strength of boom extension.
10,1 m LENGTH 17,1 m LENGTH
Radius 2. 10,1 m and 17,1 m boom extension lengths may
in #0021 #0022 #0023 #0041 #0042 #0043
be used for single line lifting service.
meters 0° 25° 45° 0° 25° 45°
OFFSET OFFSET OFFSET OFFSET OFFSET OFFSET 3. Radii listed are for a fully extended boom with
*5850 the boom extension erected. For main boom
9
(78)
lengths less than fully extended, the rated
5850 *3775
10 loads are determined by boom angle. Use
(77) (78)
5850 *4920 3775 only the column which corresponds to the
12
(74,5) (78) (77,5)
boom extension length and offset for which
5780 4700 *3360 3775
14 the machine is configured. For boom angles
(71,5) (76,5) (78) (76)
5260 4355 3215 3760 *2400 not shown, use the rating of the next lower
16
(69) (73,5) (76) (73,5) (78) boom angle.
4665 3935 3100 3480 2345
18 4. WARNING: Operation of this machine with
(66) (70,5) (73) (71,5) (77)
4100 3565 3005 3225 2310 *1750 heavier loads than the capacities listed is
20
(63) (67,5) (70) (69) (74,5) (78) strictly prohibited. Machine tipping with
3715 3250 2920 2990 2250 1690
22 boom extension occurs rapidly and without
(60,5) (64,5) (67) (66,5) (72) (76,5)
3345 2980 2800 2690 2100 1620 advance warning.
24
(57) (61) (63,5) (64) (69,5) (74) 5. Boom angle is the angle above or below
2910 2740 2610 2425 2020 1560 horizontal of the longitudinal axis of the
26
(54) (57,5) (60) (61,5) (67,5) (71)
2450 2540 2,435 2200 1920 1525 boom base section after lifting rated load.
28
(50) (54) (56) (58,5) (64,5) (68) 6. Capacities listed are with outriggers properly
2060 2290 2280 2000 1770 1480 extended and vertical jacks set only.
30
(46,5) (50,5) (52) (56) (61,5) (65)
1720 1910 2030 1830 1640 1460
32
(42,5) (46,5) (47,5) (53) (58,5) (62)
1425 1580 1635 1520 1425
34
(38,5) (42) (50) (55,5) (58,5)
1165 1285 1370 1410 1350
36
(33,5) (37) (46,5) (52) (55)
940 1030 1135 1315 1270
38
(28) (31) (43) (49) (51)
735 920 1130
40
(20,5) (38,5) (45)
735 905
42
(34,5) (40,5)
560 700
44
(30) (35)
No load stability data
Min. boom
angle for
indicated
20° 25° 45° 28° 28° 45°
length
Max. boom
length at 0° 3 0,5 m 2 7 ,4 m
boom angle
NOTE : ( ) B oom angles are in degrees . A6-82 9-1 01 61 6
*This capacity is based upon maximum boom angle.
#LMI operating code. Refer to LMI manual for instructions.
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
Grove TMS700E The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. 25
Load chart
Metric 85%
100%
11 m - 33,5 m 4990 kg 360°
6,1 m
#0101
Radius
in Main boom length in meters
meters
10,8 12,2 15,2 **18,4 21,3 24,4 27,4 30,5 33,5
55 000 38 275 36 375 *28 350
3
(69) (72) (76) (78)
47 400 38 275 36 375 28 350 *16 675
3,5
(66,5) (69,5) (74) (77,5) (78)
43 200 37 975 36 375 28 075 16 675
4
(63,5) (67) (72) (76) (77,5)
40 050 37 550 36 375 27 700 16 675 *16 675
4,5
(60) (64) (70) (74) (76,5) (78)
37 150 35 250 34 350 26 350 16 675 16 675 *14 050
5
(57) (61,5) (68) (72,5) (75,5) (77,5) (78)
31 450 29 950 29 600 23 250 16 675 16 675 14 050 *13 200
6
(50) (55,5) (64) (69) (72,5) (75) (77) (78)
26 025 25 875 25 575 20 575 16 675 15 925 13 775 12 625 *10 875
7
(42) (49) (59,5) (65,5) (69,5) (72,5) (75) (77) (78)
20 050 20 000 19 650 18 525 16 300 14 850 13 075 11 925 10 650
8
(32) (42) (54,5) (62) (66,5) (70) (73) (75) (77)
13 650 16 025 15 725 15 325 15 275 13,350 11 650 11 075 10 050
9
(16) (33) (49,5) (58,5) (63,5) (67,5) (70,5) (73) (75)
13 175 12 925 12 525 12 800 12 075 10 675 10 350 9465
10
(20,5) (44) (54,5) (60,5) (65) (68,5) (71) (73)
9140 8770 9065 9375 9275 8770 8475
12
(30) (45,5) (53,5) (59,5) (63,5) (67) (69,5)
See 6360 6690 7005 7320 7600 7735
14
Note 16 (35) (46) (53,5) (58,5) (62,5) (65,5)
4670 5035 5370 5690 5920 6155
16
(19,5) (37,5) (47) (53,5) (58) (62)
3795 4165 4495 4690 4890
18
(26) (39,5) (47,5) (53,5) (57,5)
3220 3580 3750 3920
20
(30,5) (41) (48) (53,5)
2480 2840 3010 3160
22
(16,5) (35,5) (42,5) (48,5)
2240 2395 2540
24
(24) (36) (43,5)
1885 2025
26
(28) (38)
1455 1580
28
(16) (31)
1205
30
(22,5)
Minimum boom angle (de g.) for indicate d length (no load) 0
Maximum boom le ngth (m) at 0 degre e boom angle (no load) 3 3 ,5
NOTE: ( ) Boom angles are in degrees.
#LMI operating code. Refer to LMI manual for instructions.
*This capacity is based on maximum boom angle.
Lifting capacities at zero degree boom angle
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
26 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Load chart
Metric 85%
100%
11 m - 33,5 m 4990 kg Over rear
6,1 m
#0101
Radius
in Main boom length in meters
meters
10,8 12,2 15,2 **18,4 21,3 24,4 27,4 30,5 33,5
55 000 38 275 36 375 *28 350
3
(69) (72) (76) (78)
47 400 38 275 36 375 28 350 *16 675
3,5
(66,5) (69,5) (74) (77,5) (78)
43 200 37 975 36 375 28 075 16 675
4
(63,5) (67) (72) (76) (77,5)
40 050 37 550 36 375 27 700 16 675 *16 675
4,5
(60) (64) (70) (74) (76,5) (78)
37 150 35 250 34 350 26 350 16 675 16 675 *14 050
5
(57) (61,5) (68) (72,5) (75,5) (77,5) (78)
31 450 29 950 29 600 23 250 16 675 16 675 14 050 *13 200
6
(50) (55,5) (64) (69) (72,5) (75) (77) (78)
26 825 26 025 25 675 20 575 16 675 15 925 13 775 12 625 *10 875
7
(42) (49) (59,5) (65,5) (69,5) (72,5) (75) (77) (78)
21 150 22 675 22 175 18 525 16 300 14 850 13 075 11 925 10 650
8
(32) (42) (54,5) (62) (66,5) (70) (73) (75) (77)
13 650 19 400 18 475 17 375 15 275 13 350 11 650 11 075 10 050
9
(16) (33) (49,5) (58,5) (63,5) (67,5) (70,5) (73) (75)
13 650 16 125 15 125 13 875 12 075 10 675 10 350 9465
10
(20,5) (44) (54,5) (60,5) (65) (68,5) (71) (73)
12 175 11 800 10 975 10 125 9275 8770 8475
12
(30) (45,5) (53,5) (59,5) (63,5) (67) (69,5)
See 8885 8690 8330 7910 7735 7735
14
Note 16 (35) (46) (53,5) (58,5) (62,5) (65,5)
6630 7195 7065 6825 6825 6825
16
(19,5) (37,5) (47) (53,5) (58) (62)
5685 5965 5695 5695 5695
18
(26) (39,5) (47,5) (53,5) (57,5)
4870 4830 4715 4715
20
(30,5) (41) (48) (53,5)
3925 4055 3845 3845
22
(16,5) (35,5) (42,5) (48,5)
3370 3130 3130
24
(24) (36) (43,5)
2605 2605
26
(28) (38)
2220 2170
28
(16) (31)
1,840
30
(22.5)
Minimum boom angle (deg.) for indicated length (no load) 0
Maximum boom length (m) at 0 degree boom angle (no load) 3 3 ,5
NOTE: ( ) Boom angles are in degrees.
#LMI operating code. Refer to LMI manual for instructions.
*This capacity is based on maximum boom angle.
Lifting capacities at zero degree boom angle
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
Grove TMS700E The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. 27
Load chart
Metric 85%
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
28 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Load chart
Metric 85%
100%
11 m - 33,5 m 2495 kg 360°
6,1 m
Radius #0201
in Main boom length in meters
meters
10,8 12,2 15,2 **18,4 21,3 24,4 27,4 30,5 33,5
54 500 38 275 36 375 *28 350
3
(69) (72) (76) (78)
47 400 38 275 36 375 28 350 *16 675
3,5
(66,5) (69,5) (74) (77,5) (78)
43 200 37 975 36 375 28 075 16 675
4
(63,5) (67) (72) (76) (77,5)
40 050 37 550 36 375 27 700 16 675 *16 675
4,5
(60) (64) (70) (74) (76,5) (78)
36 500 35 250 34 350 26 350 16 675 16 675 *14 050
5
(57) (61,5) (68) (72,5) (75,5) (77,5) (78)
30 400 29 950 29 600 23 250 16 675 16 675 14 050 *13 200
6
(50) (55,5) (64) (69) (72,5) (75) (77) (78)
22 225 22 150 21 950 20 575 16 675 15 925 13 775 12 625 *10 875
7
(42) (49) (59,5) (65,5) (69,5) (72,5) (75) (77) (78)
16 875 16 875 16 675 16 475 16 300 14 850 13 075 11 925 10 650
8
(32) (42) (54,5) (62) (66,5) (70) (73) (75) (77)
13 275 13 300 13 175 13 000 13 300 13 350 11 650 11 075 10 050
9
(16) (33) (49,5) (58,5) (63,5) (67,5) (70,5) (73) (75)
10 750 10 700 10 500 10 825 11 150 10 675 10 350 9465
10
(20,5) (44) (54,5) (60,5) (65) (68,5) (71) (73)
See 7335 7210 7525 7855 8180 8370 8475
12
Note 16 (30) (45,5) (53,5) (59,5) (63,5) (67) (69,5)
5085 5425 5750 6075 6250 6430
14
(35) (46) (53,5) (58,5) (62,5) (65,5)
3590 3960 4295 4620 4790 4955
16
(19,5) (37,5) (47) (53,5) (58) (62)
2860 3225 3555 3715 3875
18
(26) (39,5) (47,5) (53,5) (57,5)
2385 2740 2895 3055
20
(30,5) (41) (48) (53,5)
1725 2075 2250 2405
22
(16,5) (35,5) (42,5) (48,5)
1535 1710 1875
24
(24) (36) (43,5)
1265 1435
26
(28) (38)
890 1055
28
(16) (31)
735
30
(22,5)
Minimum boom angle (deg.) for indicated length (no load) 0
Maximum boom length (m) at 0 degree boom angle (no load) 3 3 ,5
NOTE: ( ) Boom angles are in degrees.
#LMI operating code. Refer to LMI manual for instructions.
*This capacity is based on maximum boom angle.
Lifting capacities at zero degree boom angle
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
Grove TMS700E The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. 29
Load chart
Metric 85%
100%
11 m - 33,5 m 2495 kg Over rear
6,1 m
Radius #0201
in Main boom length in meters
meters
10,8 12,2 15,2 **18,4 21,3 24,4 27,4 30,5 33,5
55 000 38 275 36 375 *28 350
3
(69) (72) (76) (78)
47 400 38 275 36 375 28 350 *16 675
3,5
(66,5) (69,5) (74) (77,5) (78)
43 200 37 975 36 375 28 075 16 675
4
(63,5) (67) (72) (76) (77,5)
40 050 37 550 36 375 27 700 16 675 *16 675
4,5
(60) (64) (70) (74) (76,5) (78)
36 500 35 250 34 350 26 350 16 675 16 675 *14 050
5
(57) (61,5) (68) (72,5) (75,5) (77,5) (78)
30 400 29 950 29 600 23 250 16 675 16 675 14 050 *13 200
6
(50) (55,5) (64) (69) (72,5) (75) (77) (78)
25 650 25 400 25 175 20 575 16 675 15 925 13 775 12 625 *10 875
7
(42) (49) (59,5) (65,5) (69,5) (72,5) (75) (77) (78)
20 200 21 425 21 275 18 525 16 300 14 850 13 075 11 925 10 650
8
(32) (42) (54,5) (62) (66,5) (70) (73) (75) (77)
13 600 17 800 17 850 17 375 15 275 13 350 11 650 11 075 10 050
9
(16) (33) (49,5) (58,5) (63,5) (67,5) (70.5) (73) (75)
13 300 14 675 14 650 13 875 12 075 10 675 10 350 9465
10
(20,5) (44) (54,5) (60,5) (65) (68.5) (71) (73)
10 375 10 375 10 750 10 125 9275 8770 8475
12
(30) (45,5) (53,5) (59,5) (63.5) (67) (69,5)
See 7660 8035 8330 7910 7735 7735
14
Note 16 (35) (46) (53,5) (58.5) (62,5) (65,5)
5750 6145 6510 6825 6825 6825
16
(19,5) (37,5) (47) (53.5) (58) (62)
4740 5120 5460 5625 5695
18
(26) (39,5) (47.5) (53,5) (57,5)
4035 4395 4550 4705
20
(30,5) (41) (48) (53,5)
3180 3535 3705 3845
22
(16,5) (35.5) (42,5) (48,5)
2840 3010 3130
24
(24) (36) (43,5)
2430 2590
26
(28) (38)
1945 2105
28
(16) (31)
1685
30
(22,5)
Minimum boom angle (deg.) for indicated length (no load) 0
Maximum boom length (m) at 0 de gree boom angle (no load) 3 3 ,5
NOTE: ( ) Boom angles are in degrees.
#LMI operating code. Refer to LMI manual for instructions.
*This capacity is based on maximum boom angle.
Lifting capacities at zero degree boom angle
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
30 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Load chart
Metric 85%
Outriggers Rotation
Boom Counterweight
NOTES:
100% 1. All capacities above the bold line are based on
11 m - 33,5 m 10,1 m - 17 m 2495 kg 360°
6,1 m
structural strength of boom extension.
10,1 m LENGTH 17,1 m LENGTH
Radius 2. 10,1 m and 17,1 m boom extension lengths may
in #0221 #0222 #0223 #0241 #0242 #0243
be used for single line lifting service.
meters 0° 25° 45° 0° 25° 45°
OFFSET OFFSET OFFSET OFFSET OFFSET OFFSET 3. Radii listed are for a fully extended boom with
*5850 the boom extension erected. For main boom
9
(78) lengths less than fully extended, the rated
5850 *3775 loads are determined by boom angle. Use
10
(77) (78)
only the column which corresponds to the
5850 *4920 3775
12
(74,5) (78) (77,5) boom extension length and offset for which
5780 4700 *3360 3775 the machine is configured. For boom angles
14
(71,5) (76,5) (78) (76)
not shown, use the rating of the next lower
5190 4355 3215 3760 *2400
16 boom angle.
(69) (73,5) (76) (73,5) (78)
4115 3935 3100 3480 2345 4. WARNING: Operation of this machine with
18
(66) (70,5) (73) (71,5) (77) heavier loads than the capacities listed is
3295 3565 3005 3225 2310 *1750
20 strictly prohibited. Machine tipping with
(63) (67,5) (70) (69) (74,5) (78)
2650 3070 2920 2990 2250 1690 boom extension occurs rapidly and without
22
(60,5) (64,5) (67) (66,5) (72) (76,5) advance warning.
2125 2480 2760 2435 2100 1620 5. Boom angle is the angle above or below
24
(57) (61) (63,5) (64) (69,5) (74)
horizontal of the longitudinal axis of the
1695 2000 2225 1975 2020 1560
26 boom base section after lifting rated load.
(54) (57,5) (60) (61,5) (67,5) (71)
1330 1590 1775 1590 1920 1525 6. Capacities listed are with outriggers properly
28
(50) (54) (56) (58,5) (64,5) (68) extended and vertical jacks set only.
1020 1245 1395 1260 1715 1480
30
(46,5) (50,5) (52) (56) (61,5) (65)
755 945 1065 980 1375 1460
32
(42,5) (46,5) (47,5) (53) (58,5) (62)
525 685 735 1075 1230
34
(38,5) (42) (50) (55,5) (58,5)
515 810 935
36
(46,5) (52) (55)
580 670
38
(49) (51)
No load stability data
Min. boom
angle for
indicated
37° 37° 45° 45° 46° 48°
length
Max. boom
length at 0° 2 4,4 m 1 8,4 m
boom angle
NOTE : ( ) B oom angles are in degrees . A6-82 9-1 01 618
*This capacity is based upon maximum boom angle.
#LMI operating code. Refer to LMI manual for instructions.
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
Grove TMS700E The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. 31
Load chart
Metric 85%
100%
11 m - 33,5 m 0 kg 360°
6,1 m
#0801
Radius
in Main boom bength in meters
meters
10,8 12,2 15,2 **18,4 21,3 24,4 27,4 30,5 33,5
54 000 38 275 36 375 *28 350
3
(69) (72) (76) (78)
47 400 38 275 36 375 28 350 *16 675
3,5
(66,5) (69,5) (74) (77,5) (78)
43 200 37 975 36 375 28 075 16 675
4
(63,5) (67) (72) (76) (77,5)
40 050 37 550 36 375 27 700 16 675 *16 675
4,5
(60) (64) (70) (74) (76,5) (78)
36 200 34 400 34 025 26 350 16 675 16 675 *14 050
5
(57) (61,5) (68) (72,5) (75,5) (77,5) (78)
26 350 26 250 26 025 23 250 16 675 16 675 14 050 *13 200
6
(50) (55,5) (64) (69) (72,5) (75) (77) (78)
18 700 18 600 18 400 18 200 16 675 15 925 13 775 12 625 *10 875
7
(42) (49) (59,5) (65,5) (69,5) (72,5) (75) (77) (78)
14 050 14 050 13 850 13 650 13 975 14 325 13 075 11 925 10 650
8
(32) (42) (54,5) (62) (66,5) (70) (73) (75) (77)
10 925 10 975 10 850 10 650 10 975 11 300 11 625 11 075 10 050
9
(16) (33) (49,5) (58,5) (63,5) (67,5) (70,5) (73) (75)
8755 8700 8505 8825 9155 9490 9695 9465
10
(20,5) (44) (54,5) (60,5) (65) (68,5) (71) (73)
See 5775 5650 5965 6290 6620 6810 6995
12
Note 16 (30) (45,5) (53,5) (59,5) (63,5) (67) (69,5)
3810 4150 4475 4800 4975 5150
14
(35) (46) (53,5) (58,5) (62,5) (65,5)
2510 2880 3220 3540 3710 3875
16
(19,5) (37,5) (47) (53,5) (58) (62)
1925 2290 2620 2780 2945
18
(26) (39,5) (47,5) (53,5) (57,5)
1560 1915 2070 2230
20
(30,5) (41) (48) (53,5)
985 1335 1515 1665
22
(16,5) (35,5) (42,5) (48,5)
870 1045 1210
24
(24) (36) (43,5)
655 825
26
(28) (38)
Minimum boom angle (deg.) for indicated length (no load) 0 14 26
Maximum boom length (m) at 0 de gree boom angle (no load) 2 7 ,4
NOTE: ( ) Boom angles are in degrees.
#LMI operating code. Refer to LMI manual for instructions.
*This capacity is based on maximum boom angle.
Lifting capacities at zero degree boom angle
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
32 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Load chart
Metric 85%
100%
11 m - 33,5 m 0 kg Over rear
6,1 m
Radius #0801
in Main boom length in meters
meters
10,8 12,2 15,2 **18,4 21,3 24,4 27,4 30,5 33,5
55 000 38 275 36 375 *28 350
3
(69) (72) (76) (78)
47 400 38 275 36 375 28 350 *16 675
3,5
(66,5) (69,5) (74) (77,5) (78)
43 200 37 975 36 375 28 075 16 675
4
(63,5) (67) (72) (76) (77,5)
40 050 37 550 36 375 27 700 16 675 *16 675
4,5
(60) (64) (70) (74) (76,5) (78)
36 200 34 400 34 025 26 350 16 675 16 675 *14 050
5
(57) (61,5) (68) (72,5) (75,5) (77,5) (78)
29 025 28 650 28 475 23 250 16 675 16 675 14 050 *13 200
6
(50) (55,5) (64) (69) (72,5) (75) (77) (78)
24 225 24 125 23 950 20 575 16 675 15 925 13 775 12 625 *10 875
7
(42) (49) (59,5) (65,5) (69,5) (72,5) (75) (77) (78)
19 250 19 450 19 475 18 350 16 300 14 850 13 075 11 925 10 650
8
(32) (42) (54,5) (62) (66,5) (70) (73) (75) (77)
13 550 15 425 15 475 15 475 15 275 13 350 11 650 11 075 10 050
9
(16) (33) (49,5) (58,5) (63,5) (67,5) (70,5) (73) (75)
12 550 12 625 12 600 13 000 12 075 10 675 10 350 9465
10
(20,5) (44) (54,5) (60,5) (65) (68,5) (71) (73)
8815 8800 9175 9565 9275 8770 8475
12
(30) (45,5) (53,5) (59,5) (63,5) (67) (69,5)
See 6370 6745 7110 7475 7660 7735
14
Note 16 (35) (46) (53,5) (58,5) (62,5) (65,5)
4660 5055 5415 5765 5935 6110
16
(19,5) (37,5) (47) (53,5) (58) (62)
3795 4175 4515 4680 4840
18
(26) (39,5) (47,5) (53,5) (57,5)
3205 3565 3720 3875
20
(30,5) (41) (48) (53,5)
2435 2790 2960 3110
22
(16,5) (35,5) (42,5) (48,5)
2165 2335 2495
24
(24) (36) (43,5)
1815 1980
26
(28) (38)
1380 1540
28
(16) (31)
1165
30
(22,5)
Minimum boom angle (deg.) for indicated length (no load) 0
Maximum boom length (m) at 0 degree boom angle (no load) 3 3 .5
NOTE: ( ) Boom angles are in degrees.
#LMI operating code. Refer to LMI manual for instructions.
*This capacity is based on maximum boom angle.
Lifting capacities at zero degree boom angle
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
Grove TMS700E The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. 33
Load chart
Metric 85%
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
34 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Working range
Metric 85%
11 m - 33,5 m main boom and 10,1 m - 17,1 m lattice extension with 12,2 m insert
44
42
40
38
70° 33,5
36
34 60° 30,5
32
50° 27,4
30
28 24,4
26 40°
21,3
24
22 30° 18,4
20
15,2
18
16 20° 12,2
14 10,8
12
10 10°
78° Max
8 boom angle
6
4 0°
2
0
62 58 54 50 46 42 38 34 30 26 22 18 14 10 6 2
60 56 52 48 44 40 36 32 28 24 20 16 12 8 4 AXIS OF
ROTATION
OPERATING RADIUS IN METERS FROM AXIS OF ROTATION
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
Grove TMS700E
The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. 35
Load chart
Metric 85%
NOTES:
11 m – 33,5 m 10,1 m - 17,1 m 6,1 m 7485 kg 100% 360°
6,1 m 1. All capacities above the bold line are based on
structural strength of boom extension.
10,1 m LENGTH 17,1 m LENGTH
Radius 2. 10,1 m and 17,1 m boom extension lengths may
#0064 #0065 #0066 #0084 #0085 #0086
in be used for single line lifting service.
meters 0° 25° 45° 0° 25° 45°
OFFSET OFFSET OFFSET OFFSET OFFSET OFFSET 3. Radii listed are for a fully extended boom with
4245 the boom extension erected. For main boom
12
(78) lengths less than fully extended, the rated
3775 *3390 2830
14 loads are determined by boom angle. Use
(75,5) (78) (78)
3320 3070 *2665 2715
only the column which corresponds to the
16
(73) (77) (78) (76) boom extension length and offset for which
2950 2750 2520 2710 the machine is configured. For boom angles
18
(70,5) (74,5) (77) (74)
not shown, use the rating of the next lower
2640 2495 2285 2470 2170
20 boom angle.
(68) (72) (74,5) (72) (78)
2365 2240 2105 2180 1935 *1705 4. WARNING: Operation of this machine with
22
(65,5) (69,5) (71,5) (69,5) (76) (78)
heavier loads than the capacities listed is
2145 2035 1930 1935 1775 1600
24 strictly prohibited. Machine tipping with
(63) (66,5) (69) (67,5) (73,5) (77,5)
1940 1870 1755 1725 1610 1470 boom extension occurs rapidly and without
26
(60) (64) (66) (65) (71,5) (75) advance warning.
1770 1710 1640 1545 1460 1310
28 5. Boom angle is the angle above or below
(57) (61) (63) (62,5) (69) (72,5)
1625 1580 1525 1385 1330 1190 horizontal of the longitudinal axis of the
30
(54,5) (58) (60) (60,5) (66,5) (70) boom base section after lifting rated load.
1475 1455 1405 1260 1215 1115 6. Capacities listed are with outriggers properly
32
(51) (55) (56,5) (58) (64) (67)
extended and vertical jacks set only.
1360 1345 1305 1120 1095 1040
34
(48) (51,5) (53) (55) (61,5) (64,5)
1225 1260 1180 1015 995 955
36
(44,5) (48) (49) (52,5) (58,5) (61,5)
995 1145 910 905 870
38
(41) (44,5) (50) (55,5) (58,5)
790 910 825 825 805
40
(37) (40) (47) (52,5) (55)
605 695 735 755 705
42
(32) (35,5) (44) (49,5) (51,5)
505 695
44
(30) (46)
545
46
(42,5)
No load stability data
Min. boom
angle at 33,5 m 22° 29° 45° 38° 40° 45°
boom length
Max. boom
length at 0° 3 0,5 m 2 4,4 m
boom angle
NOTE : ( ) B oom angles are in de gree s . A6-82 9-1 01 62 4
*This capacity is based upon maximum boom angle.
#LMI operating code. Refer to LMI manual for instructions.
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
36 The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
ON OUTRIGGERS FULLY EXTENDED - 360°
Load chart
Metric 85%
NOTES:
11 m – 33,5 m 10,1 m - 17,1 m 12,2 m 7485 kg 100% 360° 1. All capacities above the bold line are based on
6,1 m
10,1 m LENGTH 17,1 m LENGTH structural strength of boom extension.
Radius 2. 10,1 m and 17,1 m boom extension lengths may
in #0064 #0065 #0066 #0084 #0085 #0086
meters 0° 25° 45° 0° 25° 45° be used for single line lifting service.
OFFSET OFFSET OFFSET OFFSET OFFSET OFFSET 3. Radii listed are for a fully extended boom with
2925 the boom extension erected. For main boom
14
(77,5)
lengths less than fully extended, the rated
2565 *2655 1975
16
(75,5) (78) (78) loads are determined by boom angle. Use
2245 2435 *2345 1795 only the column which corresponds to the
18
(73) (77) (78) (76)
boom extension length and offset for which
1960 2180 2095 1665
20 the machine is configured. For boom angles
(71) (74,5) (77) (74)
1740 1920 1875 1505 1625 not shown, use the rating of the next lower
22
(68,5) (72,5) (74,5) (72) (78) boom angle.
1525 1710 1700 1325 1445
24 4. WARNING: Operation of this machine with
(66,5) (70) (72,5) (70) (76,5)
1345 1520 1525 1135 1270 1230 heavier loads than the capacities listed is
26
(64) (67,5) (70) (68) (74) (77,5) strictly prohibited. Machine tipping with
1210 1360 1365 1000 1135 1115 boom extension occurs rapidly and without
28
(61,5) (65,5) (67,5) (66) (72) (75,5)
advance warning.
1065 1210 1245 855 995 995
30
(59) (63) (64,5) (64) (70) (73) 5. Boom angle is the angle above or below
945 1080 1080 740 875 880 horizontal of the longitudinal axis of the
32
(56,5) (60) (62) (62) (68) (71)
boom base section after lifting rated load.
830 965 980 625 755 760
34 6. Capacities listed are with outriggers properly
(54) (57,5) (59,5) (59,5) (65,5) (68,5)
740 850 895 530 640 675 extended and vertical jacks set only.
36
(51,5) (55) (56,5) (57,5) (63,5) (66)
645 770 780 565 575
38
(48,5) (52) (53,5) (61) (63,5)
570 675 675 505
40
(45,5) (49) (50) (61)
590 615
42
(45,5) (46,5)
505
44
(42)
No load stability data
Min. boom
angle at 33,5 m 40° 40° 46° 56° 58° 60°
boom length
Max. boom
length at 0° 2 1 ,3 m 1 2 ,2 m
boom angle
NOTE : ( ) B oom angles are in degrees . A6-82 9-1 01 62 8A
*This capacity is based upon maximum boom angle.
#LMI operating code. Refer to LMI manual for instructions.
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE.
Grove TMS700E The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. 37
Symbols glossary
Transmission
38
Notes
Grove TMS700E 39
Manitowoc Cranes
Regional headquarters
Americas Europe, Middle East, Africa China Greater Asia-Pacific
Manitowoc, Wisconsin, USA Dardilly, France Shanghai, China Singapore
Tel: +1 920 684 6621 Tel: +33 (0)4 72 18 20 20 Tel: +86 21 6457 0066 Tel: +65 6264 1188
Fax: +1 920 683 6277 Fax: +33 (0)4 72 18 20 00 Fax: +86 21 6457 4955 Fax: +65 6862 4040
Shady Grove, Pennsylvania, USA
Tel: +1 717 597 8121
Fax: +1 717 597 4062
Regional offices
Americas
Brazil
China
Beijing
Factories This document is non-contractual. Constant improvement and engineering progress
make it necessary that we reserve the right to make specification, equipment, and
Brazil price changes without notice. Illustrations shown may include optional equipment
Alphaville Chengdu and accessories and may not include all standard equipment.
Passo Fundo
Mexico Guangzhou
China
Monterrey Xian
TaiAn
Chile
Zhangjiagang
Santiago Greater Asia-Pacific
France
Australia
Charlieu
Europe, Middle East, Brisbane
Moulins
Africa Melbourne
Germany
France Sydney
Wilhelmshaven
Baudemont India
India
Cergy Chennai
Pune
Decines Delhi
Italy
Germany Hyderabad
Niella Tanaro
Langenfeld Pune
Portugal
Italy Korea
Baltar
Lainate Seoul
Fânzeres
Netherlands Philippines
Slovakia
Breda Makati City
Saris
Poland Singapore
USA
Warsaw
Manitowoc
Portugal
Port Washington
Baltar
Shady Grove
Russia
Moscow
South Africa
Johannesburg
U.A.E.
Dubai
U.K.
Buckingham
©2014 Manitowoc
Form No. TMS700E PG
Part No. 00-024 / 2M / 0814 PDF update www.manitowoccranes.com