Вы находитесь на странице: 1из 2

Nitomortar B constructive solutions

High strength epoxy resin bearing mortar

Uses Surface preparation

For the formation of bridge bearing pad levelling plinths. Can All grease, oil, chemical contamination, dust laitence and
also be used as a high strength horizontal repair for concrete loose concrete must be removed by scarifying. The surface
structures. must then be etched with Fosroc Acid Etch. After the
reaction has ceased, the surface should be thoroughly
washed with clean water and allowed to dry.
Description
Priming
Nitomortar B is a specially selected solvent free epoxy
system together with high quality silica aggregates. It is
Priming is not normally required in a pure load bearing
supplied as a three pack material in pre-weighed quantities
situation. However, if a good bond is essential, particularly
ready for on site use. When components are mixed together
in a repair situation, the properly prepared concrete should
the system cures to form a strong and durable mortar.
be primed with Nitoprime 30/31 and the Nitomortar B
applied to the primer whilst it is still tacky.
Advantages
Mixing
Speed: Early development of initial hardness
and high early strength, speeds The Nitomortar B base and hardener components should be
construction operations. Reaches thoroughly mixed in the base container and then added to
2
over 90 N/mm at 24 hours. the mixed aggregates in a Mixal or Kol type mixer using a
low speed. Mixing should continue for 2 to 3 minutes until
Quality: Pre-weighed laboratory controlled all the components are thoroughly blended.
materials ensure consistency and
eliminate source of operative error. Trowelling

Durability: Maintains high level of impact and The mixed material is applied to the surface with a steel
abrasion resistance. trowel in approximately 12 mm (½”) layers taking care that it
is well compacted. During cold weather it may be
Waterproof: Will cure even under damp condition. necessary to protect the work by temporary tenting and to
Cured material is completely assist curing by means of warm air blowers. Minimum
o
impermeable to water. application temperature 5 C.

Locally produced: Formulated for use in Middle East Nitomortar B should not be applied in layers exceeding 50
conditions. mm (2”) thick. Where greater thickness is required,
subsequent layers can be built up 18 hours after application
of the preceding layer.
Properties
o
Cleaning
Pot life: 40 minutes at 30 C
3
Density: 2170 kg/m (fully compacted) Uncured Nitomortar B can be removed with Fosroc Solvent
o
102. Tools and equipment should be cleaned with Fosroc
Physical properties (25 C) Solvent 102 immediately after use.
2
N/mm at Test
24 hours method Precautions
BS 1881 Part 4
Compressive Strength: 96 1970 Clause 2 Health and safety
BS 4551 Part 1
Flexural strength: 36 1970 (10.3) Some people are sensitive to epoxy resins so gloves and a
BS12 1958 barrier cream, Exaderm or similar, should be used when
Tensile strength: 17 Appendix H handling these products. If contact with the resin occurs, it
Yong’s modulus must be removed, before it hardens, with a resin removing
ASTM C469
strength: cream such as Kerocleanse 22 and Roxalex 42. Follow by
5600 (modified)
washing with soap and water. Do not use Solvent.

The use of goggles is recommended but should accidental


eye contamination occur wash thoroughly with plenty of
water and seek medical treatment immediately. Ensure
good ventilation and do not smoke during use.

Page 1
Nitomortar B
Packing and coverage

Nitomortar B: 16 kg pack. 16 kg pack yielding


approximately 7.2 litres when
fully compacted
Fosroc Solvent 102: 4 litres can
Fosroc Acid Etch: 30 litres carboys

Storage
o
Shelf life 12 months at 20 C when stored in a dry place.

Fire

Fosroc Solvent 102 is inflammable. Ensure adequate


ventilation and do not use near a naked flame.

Flash point
o
Fosroc Solvent 102: 33 C

Supply

Reference should be made to our local Technical Field staff


or local agents. Contract supplies may be arranged with the
factory in Jeddah.

Technical service

An advisory service is maintained from Jeddah for on-site


assistance and advice on the use of the Fosroc product
range. This service is supported by a team of specialists in
the filed.

Additional information

Technical data and guidance can be provided on a wide


range of concrete admixtures and surface treatments, in
addition to repair materials, grouts, industrial flooring and
waterproofing.

Important note:
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions
for the Supply of Goods and Services, copies of which may be obtained on request. Whilst Fosroc endeavours to ensure that
any advice, recommendation, specification of information it may give is accurate and correct, it cannot, because it has no direct
or continuous control over where or how its products are applied, accept any liability either directly or indirectly arising from the
use of its products, whether or not in accordance with any advice, specification, recommendation of information given by it.

Fosam Company Limited


Telephone: +966 2 637 5345 Fax: +966 2 637 5891 email: fosam@fosroc.com
Head Office
Post Box 11081 Regional Offices
Jeddah Sales Office Tel: (02) 608 0999 Fax: (02) 638 0693 Yanbu Tel: (04) 322 4280 Fax: (04) 391 2980
Jeddah – 21453
Jeddah Showroom Tel: (02) 665 0187 Fax: (02) 667 4844 Makkah Tel: (02) 542 0869 Fax: (02) 542 0869
Saudi Arabia Riyadh Tel: (01) 482 9303 Fax: (01) 482 7562 Medinah Tel: (04) 855 0091 Fax: (04) 855 0047
Dammam Tel: (03) 814 1282 Fax: (03) 814 1581 Jubail Tel: (03) 362 3904 Fax: (03) 362 3875

www.fosroc.com Khamis Mushayt Tel: (07) 250 0469 Fax: (07) 250 0469 CSD Tel: (02) 608 0999 Fax: (02) 638 0693

Registered Office: Industrial Area, Phase 4, Road No. 414, Street No. 407
Page 2 FO SA/NITOMORTAR B/05/A

Вам также может понравиться