Академический Документы
Профессиональный Документы
Культура Документы
Abstract—Pada makalah ini dipaparkan faktor teknis yang A. Material aktif (ukuran partikel, ukuran poros dan
sangat penting dalam penelitian, desain, dan pengukuran EDLCs. functional group)
Diharapkan dengan memahami secara fundamental faktor-faktor Karbon aktif (activated carbon) menjadi material aktif yang
yang mempengarahui kinerja elektroda, elektrolit, dan interaksi digunakan secara luas untuk aplikasi EDLCs karena memiliki
elektroda-elektrolit, maka peneliti atau insinyur akan dengan
luas permukaan (SSA) yang sangat tinggi, dan harga yang
akurat dan cepat untuk mendesain EDLCs dengan kualitas tinggi.
Dengan mempertimbangkan hal-hal teknis yang telah menjadi relative rendah. Namun untuk mendapatkan unjuk kerja EDLCs
kaidah dasar yang sudah diuji dan diformulasikan oleh para yang tinggi maka beberapa hal terkait sifat fisik dan kimia poros
ilmuwan dibidang ini sebelumnya maka peneliti atau insinyur harus diperhatikan, seperti luas permukaan poros (SSA), ukuran
tidak akan mengulangi hal yang ama atau mengalami kesalahan dan distribusi partikel, ukuran dan distribusi poros, dan
pada hal-hal yang sudah diketahui pengaruhnya. Dalam hal functional-group permukaan poros.3,4,5
pengukuran atau karakterisasi, konsistensi dalam normalisasi Secara teoritis, besar kapasitansi superkapasitor sangat
kapasitansi dan Ragone plot akan memudahkan para peneliti dan dipengaruhi oleh luas area (A) material aktif dan dan ketebalan
insiyur dalam mengevaluasi produk-produk baru EDLCs. double layer (d), sebagai berikut:6
Keywords—Energy storage, Electrochemical double layer
Capacitor/EDLCs, Karbon aktif, Kapasitansi, Densitas Energi = (1)
kecil lebih banyak (D90) atau memiliki kerapatan Secara umum elektrolit organik memiliki ukuran ion terlarut
tumpukan/kerapatan tinggi akan meningkatkan nilai Rct.8 yang sangat besar dan konstanta dielektrik rendah, dimana
menghasilkan kapasitansi EDLCs yang relatif rendah.
Gambar 3. Skematik pengaruh film density terhadap kapasitansi gravimetrik Sebagaimana dijelaskan pada sub-bahasan pengaruh ukuran
dan kapasitansi volumetric
poros material aktif diatas, kapasitansi SCs tidak hanya
D. Pemilihan dan optimalisasi elektrolit dipengaruhi oleh luas permukaan material aktif tetapi juga
Elektrolit sangat mempengaruhi unjuk kerja dari ukuran poros dan distribusi ukurannya. Kemampuan akses
superkapasitor elektrokimia (SCs). Oleh karena itu merancang poros sangat ditentukan oleh sifat-sifat elektrolit, seperti;
dan optimalisasi elektrolit sangat diperlukan untuk ukuran anion (n-) dan kation (n+) , dan interkasi antara ion dan
mendapatkan kualitas superkapasitor yang optimal. pelarutnya.14 Oleh karena itu sangat penting untuk memilih
Secara skematik, pengaruh sifat-sifat elektrolit terhadap ukuran ion elektrolit yang sesuai dengan ukuran poros material
karakteristik superkapasitor ditunjukkan pada gambar 4. Sifat- aktif.
sifat dasar kapasitor elektrokimia, seperti; (1) jenis dan ukuran Kerusakan dan kegagalan elektrolit juga menjadi isu yang
ion, (2) konsentrasi ion dan pelarut, (3) interaksi antara ion dan sangat penting bagi elektrolit organik. Degradasi elektrolit
pelarut, (4) interaksi elektrolit dan material elektroda, (5) organik disebabkan oleh beberapa hal berikut; (1)Rentan
Potential window, semua mempengaruhi kapasitansi EDLCs tegangan window terlalu tinggi dapat mengoksidasi elektrolit
dan pseudo-kapasitor, Densitas Energi dan daya, dan juga umur organik. Penggunaan tegangan di atas 3V dapat menginisiasi
pakai (cycle life).13 reaksi oksidasi yang menghasilkan evoluasi gas karena
Pada makalah ini pembahasan elektrolit akan difokuskan dekomposisi elektrolit dan oksidasi elektrokimia karbon, (2)
pada elektrolit organik untuk EDLCs. Dipasar komersial, reaksi elektrokimia pada elektrolit, (3)lingkungan kerja SCs
superkapasitor mulai didominasi oleh EDLCs yang memiliki pada temperatur dan tegangan kerja yang terlalu tinggi.13
rentang tegangan window 2.5 s/d 2.8V. Peningkatan tegangan Hal penting lainnya dari elektrolit adalah interaksinya
window sangat berpengaruh pada perbaikan densitas energi dan dengan material non-aktif lain dari struktur sel-eletroda. Dalam
daya. kontek superkapasitor berbasis elektrolit organik, mayoritas
menggunakan Al sebagai konduktor arus. Penggunaan jenis
garam konduktif pada elektrolit dapat berpengaruh besar pada
sifat elektrokimia konduktor arus Al dalam elektrolit organik.15
Interaksi elektrolit dengan binder dapat mempengaruhi
kemampuan serap elektrolit pada material aktif. Penggunaan
binder yang kurang tepat akan menurukan wettability elektroda.
Dilaporkan bahwa penggunaan PVDF menunjukkan wettability
[DIPEA][TFSI] IL yang lebih baik daripada CMC-SBR, namun
pada [Pyrr][TFSI] kedua binder menunjukkan wettability yang
sama.16
Separator selulosa banyak digunakan pada EDLCs dengan
elektrolit organik (TEABF4/ACN), namun kandungan air pada
elektrolit dapat mempercepat kerusakan EDLCs ketika
separator selulosa digunakan.17 Jadi sangat diperlukan
memastikan kompatibilitas separator dengan elektrolit yang
digunakan.
luas permukaan, dan menurunkan kinetika difusi ion dalam permukaan. Penting untuk diperhatikan bahwa normalisasi
poros. Sehingga sangat direkomendasikan untuk mereduksi kapasitansi ini adalah cara yang logis dalam membandingkan
serendah mungkin kandungan air pada elektroda dan elektrolit. dan evaluasi berbagai macam material aktif EDLCs.
III. FAKTOR-FAKTOR PENTING DALAM KARAKTERISASI B. Komparasi divais penyimpan energ listrik
Zion market research, USA, memprediksi pasar Dalam hal perbandingan produk EDLCs maka yang
superkapasitor akan naik mencapai lebih dari 200% pada tahun digunakan adalah kapasitansi divais, bukan kapasitansi
2022 dari pendapatan penjualan lebih dari 700.000$US pada elektroda. Sehingga faktor normalisasi yang digunakan adalah
tahun 2017.18 Superkapasitor Electrochemical Double-Layer berat dan volum seluruh divais, seperti; logam konduktor arus,
(EDLCs) semakin banyak dikembangkan karena memiliki separator, elektrolit, dan packaging.19
unjuk kerja yang mendekati kebutuhan komersial dengan harga Untuk membandingkan divais EDLCs dengan penyimpan
yang kompetitif. Sehingga penelitian EDLCs pun menjadi energy listrik lainnya sering digunakan Ragone plot, dimana
sangat menarik dan berkembang pesat. densitas energi divais (Wh) dibandingkan terhadap densitas
Ditengah perkembangan penelitian dan pengembangan daya divais (W). Penemuan baru EDLCs biasanya
EDLCs yang terus meningkat dari tahun ke tahun, ada dibandingkan densitas energi dan dayanya dengan baterai
kebutuhan teknis yang sangat mendesak yaitu menetapkan komersial. Sebagaimana diuraikan diatas, agar komparasi yang
standard pengujian, dan evaluasi karakteristiknya sehingga dilakukan rasional maka normalisasi terhadap berat dan volum
memudahkan dalam membandingkan berbagai jenis bahan divais juga harus dilakukan pada perbandingan menggunakan
elektroda dan elektrolit yang digunakan. Dua hal yang harus Ragone plot.21
menjadi perhatian dalam pengukuran EDLCs adalah (1)
konsistensi dan parameter normalisasi yang baku dalam IV. KESIMPULAN
membandingkan EDLCs ,(2) konsistensi dalam penggunaan Untuk menghasikan produk EDLCs dengan kualitas tinggi
metoda/prosedur pengukuran atau karakterisasi. Sebagai sesuai dengan standar yang diperlukan untuk kendaraan listrik
contoh, densitas energy dan daya dapat di normalisasi dalam dan berbagai keperluan elektronik, perlukan diperhatikan
tiga versi yaitu 1) volume material aktif, 2) masa material aktif, faktor-faktor utama, seperti karakteristik karbon aktif dan
dan 3) luas permukaan yang dimiliki material aktif.19 elektrolit. Karena secara fundamental densitas energi dan daya
EDLCs sangat dipengaruhi oleh interaksi material aktif dan
A. Konsistensi parameter normalisasi elektrolit, maka kompalibilitas antara kedua harus menjadi
Komparasi kapasitansi, energi dan daya berbagai jenis faktor utama, dan optimalisasi interaksi pada daerah antar muka
material elektroda dari pengukuran devais SCs hanya dapat menjadi kunci kualitas.
dilakukan dengan menormalisasi terhadap berat, volum, dan Selain itu, faktor-faktor degradasi juga harus menjadi
luas permukaan yang kemudian masing-masing disebut perhatian terutama upaya mereduksi kandungan air pada semua
kapasitansi gravimetrik, kapasitansi volumetrik, dan material yang digunakan pada EDLCs, dan pemilihan elektrolit
kapasitansi normal. yang sesuai.
Berdasarkan gambar 1, sel kapasitor terdiri dari 2 elektroda Standarisasi dan konsistensi penggunaan standard
yang membentuk 2 Electrochemical Double Layer. Sehingga pengukuran menjadi kebutuhan kedepan sehingga komparasi
satu sel penuh superkapasitor adalah 2 kapasitor yang produk EDLCs mudah untuk dilakukan dan pada produk baru
ditrangkai secara seri, dengan nilai kapasitansi totalnya bisa secara menyakinkan dievaluasi dengan media penyimpan
adalah;20 energi listrik yang komersial.
Abstract—Stigma is one of the social forms that occur in The results of research in Indonesia reported that
labeling, withdrawal, loss status and discrimina-tion. The among women still stigmatized against ODHA [5]. The
stigma about people living with HIV/AIDS (PLWHA) is stigma of housewives against HIV/AIDS in Jember
manifested by social rejection, lack of acknowledgment
and discrimi-nation that will cause shame and fear for coffee plantation area was 33.3% [6]. The impact of
PLWHA to be invited to others. Spirituality can reduce stigma on people with HIV/AIDS (PLWHA) includes
the stigma that exists in peoples’ lives. There are still social, economic and health aspects [7].
limited studies explored the house wife stigma regarding
Stigma comes from the thought of an individual or
PLWHA. This study purposed to ana-lyze the relationship
between spirituality with the stigma of house wife about community who believes that AIDS is a result of
PLWHA in Jember, the east part of Java Island, immoral behavior and cannot be accepted by society
Indonesia. This re-search applied descriptive correlation [8]. Stigma in community is formed due to lackof
design with cross sectional approach. The sampling was
counted 84 of house wife who were reached by using knowledge, perception, access to information about
proportionate random sampling. The results showed that HIV/AIDS, attitudes (family, neighbors and community
the median value of spirituality was 37.00 and stigma was leaders) and religion [5] [9]. Religious activities can
17.00. Bivariate analysis using Spearman Rank Test
reduce the stigma of HIV/AIDS. Observations through
showed that there was no correlation between spirituality
and stigma of house wife about PLWHA (p value 0.213). qualitative interviews recognize that there is a religious
Alt-hough there was no correlation between spirituali-ty impact on the stigma of HIV/AIDS, where religion is
and stigma, it does not mean the two variables are not part of spirituality [9][10]. The function of spirituality
important. Health workers are expected to improve
spirituality among house wife in order to reduce stigma has similarities with religiosity in the sense of helping
about PLWH in society, especially among house wife. individuals understand various things or problems in
their lives, but the framework used to understand these
Index Terms—HIV AIDS, house wife, religious, problems may have differences [11].
spirituality, stigma Spirituality affects the health and well-being of life
I. INTRODUCTION and acts as a source of support or strength for
individuals [12][13]. Healthy spirituality should be able
HIV/AIDS infection causes an impact on the to benefit others, whatever their beliefs can live mutual
community, including on the social and economic aspects, respect, side by side, fighting for spiritual life according
where on the social aspect stigma is found in the to their beliefs [14]. There are limited studies that
community [1] [2]. One of the biggest obstacles to explore attitudes and responses of housewives related to
preventing and overcoming HIV/ AIDS is the high stigma PLWHA. This study This study aims to analyze the
and discrimination against people living with HIV/AIDS relationship between spirituality and the stigma of
(PLWHA), stigma and discrimination undermine the housewives about people with HIV/AIDS in Jember,
ability of individuals and communities to protect Indonesia.
themselves from HIV infection and stay healthy even
though they live with HIV/AIDS [3]. According to
UNAIDS, reports in 35 countries with available data of
more than 50% of people have a stigma and
discriminatory attitude towards PLWHA [4].
II. METHODS Table 4. Stigma of Housewives in Jember (n: 84)
Variables Median Min-Maks
The study used a descriptive correlative research Stigma 17.00 10-26
design using cross sectional approach. The population in a. Stereotypes 6.00 3-12
this study was housewives in Jember Regency, b. Self-acceptance 4.00 2-7
amounting to 24,205 people and the sample in this study c. Problems Disclosures 2.00 1-4
were 84 housewives collected by using proportionate d. Social relations 4.00 2-7
random sampling. Sampling in each village was done by
randomization. This study was conducted in 12 villages Table 5. the Relationship between Spirituality
and Stigma of Housewives
in the Puger sub-district of Jember Regency during May
Variable Stigma
2018.
Spirituality r 0.137
Collecting data on spirituality and stigma using the p value 0.213
Facit-Sp12 questionnaire and stigma questionnaire. The
Facit-Sp 12 questionnaire consists of 12 questions and a III. DISCUSSION
stigma questionnaire consisting of 9 questions. Analysis
of univariate data, carried out by first testing normality The results of the study showed that the median age
for numerical data. Test for normality using the test of of the respondents was 32.00 years old, where age
Kolmogorov-Smirnov. The analysis of bivariate used the 32.00 years including adult age. The more mature a
Spearman Rank test. This test was used to determine the person, it leads to the better spirituality. Adulthood is a
relationship between the two determined variables. period of self-confidence that begins with the process of
declaring a rational belief or value [15].
Table 1. Characteristics of Respondents of The results of the study for “the meaning of life”
Housewives in Puger District, Jember District, 2018 indicator shows a median of 12.00, meaning that the
(n = 84) respondent chooses answers in the Likert scale 3
Variables (f) (%) (which mean very often). For example on the
Education Levels
questionnaire "I have a reason for my life and life has
a. SD 48 57.1
b. SMP 22 26.2 been meaningful", it proofs that respondent has a reason
c. SMA 14 16.7 to live and indicate of having good spiritual condition.
84 100 A person has a reason to live and has meaning in life
Religion can represent the cognitive aspects of the individual's
Islam 84 100 welfare [12]. Spirituality can help a person find the
84 100 meaning of his/her life, encourage him to always think
and do good and establish harmony with God, nature
Table 2. Age of Housewives in the district of Jember
and society [16].
(n: 84)
The results of “the peace” indicator research show a
variable Median Min-Max
median of 12.00, meaning that the respondent chooses 3
Age (Year) 32.00 23-46 in the Likert Scale answers (very often). Peace is a state
that makes harmonious and enduring relationships in
life. This peace is the achievement of great spirituality.
Table 3. Spirituality of Housewives in Jember Peace and its formation for some people who cannot be
(n:84)
separated from justice inherent in a person, where a
Variable Median Min-Maks
person can live and be in a natural and healing
Spirituality 37.00 25-48
a. Meaning of life 12.00 9-16 environment [14]. For example in questionnaire number
b. Confidence 12.00 8-16 1 "I feel satisfied and peaceful with life" the respondent
c. Peace 12.00 8-16 chose answer 3 (very often), it becomes evidence that
someone has quite often peace in their daily lives that
makes a person can live comfortably and peacefully.
The results of the confidence indicator research
show a median of 12.00, meaning that the respondent
chooses 3 answers (very often) in the Likert Scale
answers. In questionnaire number 9 "I find comfort in
the spiritual life that I believe in". Spiritual belief
consists of the stages of faith, thought and discovery.
The spirituality stage should arrive at the stage of Analysis of Spirituality Relations with the Stigma of
discovery, where every human being can benefit Housewives Regarding People with HIV/AIDS in
others, whatever their beliefs can live mutual respect, Jember District
side by side, fighting for spiritual life according to The results of this study indicate that there is no
their beliefs. This is the life that benefits for the significant relationship between spirituality and stigma
whole universe and creates peace for all [14]. among housewife about people with HIV/AIDS in
The median score for spirituality of respondents is Jember District where the p value is 0.213 (ɑ ≥ 0.05)
37.00, it shows that the respondent chooses 3 which means that H0 failed to be rejected. Other studies
answers (very often), meaning that the respondent also conducted that there was no relationship between
has a good spiritual. spiritual and stigma [21].
Factors that influence stigma are knowledge,
Stigma of Housewives perception, access to information, attitudes and religion
The results of the study showed that the last [5]. Knowledge about HIV/AIDS affects a person's
education of respondents was: Primary School attitude towards PLWHA. Knowledge is formed because
(Elementary school) with a total of 48 (57.1%). This of the lack of ignorance about HIV/AIDS, especially in the
study is in line with the research conducted by Rifai mechanism of HIV transmission in groups of people at
(2016) that the level of education of housewives who risk and how to prevent it, including the use of condoms.
Giving knowledge and information about HIV/AIDS is an
have the most stigma is at the elementary level as
effective way to prevent and reduce stigma about PLWHA
many as 7 people (46.7%). Elementary school is
[5].
included in the low education level which is one of
Another factor that influences stigma is perception.
the factors influencing the stigma about PLWHA
Perceptions of PLWHA influence how people behave
where the community has an inappropriate
and behave towards PLWHA such as blaming, shame,
conclusion regarding actual HIV/AIDS [17].
giving negative values and judging related to the
The stigma against PLWHA is caused by
disease [5]. Perception of negative treatment in the
assuming that PLWHA are dirty people, doing
form of avoidance, humiliation and rejection in social
immoral things such as drug users, and dating
interaction [22]. Negative treatment arises from fear of
commercial sex workers. This behavior makes one
contracting, where a person is uncomfortable at direct
tends to be afraid and have excessive negative views
contact with PLWHA [23]. Perceptions about
if living with an HIV person [18]. Stigma is
HIV/AIDS relate significantly to the stigma of PLWHA
manifested by social rejection, lack of recognition
[24]. Researchers argue that perception affects a
and discrimination that will cause shame and fear for
person's stigma about PLWHA, if someone has a
PLWHA to interact with other people [6].
negative perception of PLWHA, it will have an impact
Based on the results of the study the median value
on the treatment and prevention of people infected with
of the highest stigma indicator was found in the
HIV/AIDS.
stereotype indicator which was 6.00. Stereotypes
Another factor that influences stigma is access to
causes stigma and discrimination, the emergence of
information. Information media such as television,
stereotypes due to the beliefs that individuals have
newspapers, radio and magazines are access to
toward individual or group characteristics [19].
information chosen by the community to get
Stigma occurs when the general public agrees with a
information about HIV/AIDS. Information access is
person's bad stereotype [20]. Stereotype is a
used to provide knowledge, attitudes and behaviors to
cognitive aspect or frame of mind which consists of
prevent HIV/AIDS transmission and reduce stigma [5].
belief and knowledge about a particular social group
Another factor that influences stigma is attitude. A
[19]. Based on this theory, it can be concluded that
person's attitude is very important in giving stigma
stereotypes are prejudices or beliefs about PLWHA
because it can affect the stigma of PLWHA, for
in the community. It can be assumed that the stigma
example a family that is the closest environment to
of housewives in Puger District, Jember Regency still
PLWHA, where the family feels ashamed of one of the
has stigma, one of which is by giving stereotypes
family members who are infected with HIV/AIDS [5].
about PLWHA.
Another factor influencing stigma is religion. V. REFERENCES
Religion has similarities with spirituality in the sense
that it helps individuals understand various problems [1] World Health Organization. 2017. 10 Facts on
HIV/AIDS. 2017. Available from:
in their lives, but the framework used to understand
http://www.who.int/features/factfiles/hiv/en/
these problems may have differences, where in [2] Olalekan AW, AR Akintude., And MV
religion there are foundations of theology, guidelines, Olatunji Perception of societal stigma and
and guidelines from religion [11]. Other research discrimination towards people living with
states that religiosity and spirituality can be separated HIV/AIDS in lagos, nigeria: a qualitative
conceptually because religiosity has a structure of study. Mater Sociomed. 2014 Jun; 26 (3):
theology and formality that is not possessed by 191-194
[3] Joint United Nations Program on HIV and
spirituality, but in the reality of individual life both
AIDS. 2014. Reduction of HIV-Related
tend to be interrelated [25]. Religious knowledge has stigma and discrimination. 2014
a strong role in the way of thinking and patterns of [4] Joint United Nations Program on HIV and
human behavior. Religion can be used as a tool of AIDS 2015. On the fast-track to end AIDS
justification and legitimacy for someone to give by 2030: Focus on Location and Population.
attitudes and actions where religion teaches mutual 2015
[5] Syaluhiyah, et al. Community stigma against
love without any difference [17]. Compliance with
HIV/AIDS. National Public Health Journal.
religious values has an important role in HIV 2015. 9 (4): 333-338
prevention, for example religious activities can [6] Rifai, A. 2016. Application of brief
influence a person's attitude and behavior. Religious psychoeducation on HIV/AIDS stigma and
activities can reduce stigma about HIV/AIDS [9] - utilization of VCT in housewives in
[10]. The religious attribution categorizes PLWHA plantation areas
as a sinner and in stigmatizing causes distance and [7] Avert. 2017. HIV stigma and discrimination.
UK: Avert
separation from others so that there is a lack of
[8] Philip J, Chadee D, Yearwood RP Health care
sympathy for PLWHA [9]. students reactions towards HIV patients:
Based on several studies, researchers assume that examining prejudice, emotions, attribution
there is no relationship between spirituality and of blame and willingness to interact with
stigma because there are still other spirituality factors HIV/AIDS patients. AIDS CARE. 2014
that influence stigma such as religion, where religion March; 26 (10): 1236-41
has an important role in individual life, thus forming [9] Muturi N, Soontae A. HIV/AIDS stigma and
religiosity among african american women.
concepts of religiosity and spirituality. In addition,
Journal of Health Communication. 2010 Jun;
other research states that there is no relationship 15 (4): 388-401 Master's Degree Program in
between spiritual and stigma, in spiritual research Social and Welfare Development UGM;
consisting of three indicators, one of which is 2016
religion, existential and spiritual [21]. [10] Diaz NT, TB Neilands, SM Rivera, E.
Betancourt. Religion and HIV/AIDS stigma:
for health professionals in puerto rico.
IV. CONCLUSIONS Global Public Health. May 2010; 5 (3): 295-
There is no significant relationship between 312
spirituality and the stigma of housewives regarding [11] Amir Y, Lesmawati DR Religiosity and
people with HIV/AIDS (PLWHA) in Jember District. spirituality: the same or different concepts?
This research can be an input for further research Scientific Journal of Psychological
to find out other factors that can influence stigma and Research. 2016 Nov; 2 (2): 67-73
[12] Taylor L, Le M. Fundamentals of nursing:
for spirituality variables to conduct for further
the art and Ssience of nursing care.
research related to other spirituality factors such as Philadelphia: Lipincot; 1997
religion, where religion has an important role in [13] Potter PA, Perry, AG Fundamental nursing
individual life, thus forming the concepts of textbooks: concepts, processes and practices.
religiosity and spirituality. ed 4 language change. Jakarta: EGC; 2005
[14] Yusuf A, Nihayati HE, Iswari MF,
Acknowledgments Okviasanti F. Spiritual needs: concepts and
Author would like to thank "Puger Sub-District of applications in nursing care. Jakarta: Mitra
Jember Regency" Wacana Media; 2016
[15] Hamid AY Potpourri of mental nursing care.
Jakarta: EGC; 2008
[16] Nelson JM Psychology, religion and southern appalachia. Issues Ment Health
spirituality. New York: Springer Science Nurs.2018 Jun; 39 (6): 482-489
Business Media; 2009 [22] X Li, Wang, H, Feenni K, William AB
[17] Kharis A. Stigma and the causes of Shadow on my heart: a culturally grounded
community stigma against HIV/AIDS concept of HIV stigma among Chinese
housewives. [Thesis] Yogyakarta; 2016 injection drug users. JAN AIDS CARE.
[18] Hermawati P. Relation of the perception of 2012 Jan / Feb; 23 (1): 52-62
PLWHA to the HIV/AIDS stigma of the [23] Bogart LM, Burton O, Cowgill, David K,
community with social interaction with Gery R, Debra A, Murphy, Jacinta E, US
PLWHA. [Thesis]. Jakarta: Faculty of Mark HIV-related stigma among people
Piskology, Syarif Hidayatullah State Islamic with HIV and their families: a qualitative
University; 2011 analysis . AIDS Behav. 2008 Apr; 12 (2):
[19] Scheid TL, TN Brown. A handbook for the 244-54
study of mental health: social contexts, [24] Febrianti. Factors related to stigma against
theoresis, and systems. American: people with HIV/AIDS (PLWHA).
Cambridge University Press; 2010 Endurance Journal. 2017 Jun; 2 (2): 158-167
[20] Ardani I, Handayani S. Stigma against [25] Davis TL, Barbara AK, Sharon ERK
people with HIV/AIDS (PLWHA) as an Meaning, purpose, and religiosity in at-risk
obstacle to seeking treatment: a case study of youth: the relationship between anxiety and
injecting drug addicts in Jakarta. Health spirituality. Journal of Psychologhy and
Research Bulletin. 2017 Jun; 45 (2): 81-88 Theology. 2003 Dec; 10 (31): 356-365
[21] HutsonS P, Darling C,Hall JM,Heidel RE,S
Gaskins. Stigma and spiritual well-being
among people living with HIV/AIDS in
1
the prospect of eternal life in heaven (Fidrmuc and Tunali, to any countries which are attributed to specific religion.
2015). Internal religiosity also causes spillover effects to In this report, happiness is measured by weighted score on
non-religious people since people tend to be more satisfied a scale ranging from 0 to 10 which consists of real GDP
living in more religious regions (Steiner et al, 2010), per capita, social support, life expectancy, freedom of life
whereas living in religious diversity will decrease the choices, generosity, and trust or absence of corruption in
happiness level (Mookerjee and Beron, 2005). government and business. Norway is the happiest country
External religiosity is also shown to have positive in the world as followed by Denmark, Iceland, and
impact on happiness. Hayo (2007) found that church Switzerland in a tight score, and six other secular countries
attendance increases the probability of greater happiness, are dominating in the top ten. On the other hand, the
and the impact is stronger than internal religiosity (Clark highest rank of religious country which refers to muslim
and Lelkes, 2009), particularly for Afro-Americans country is United Arab Emirates on 21st position.
(Ellison and Gay, 1990). In this case, some people may Meanwhile, Indonesia, as a predominantly muslim country
find peace through religious sermons in which various in the world with higher levels of religious diversity, are
verses in holy book are recited. In line with this result, far left behind on 81st position out of 155 countries.
Greene and Yoon (2004) found that happiness increases Hence, the positive link between religiosity and happiness
with religious attachement as measured by willingness to as suggested by previous research seems questionable and
attend religious services regularly. On the other hand, needs to investigate further.
Putnam (2009) argued that it is not church going that has In this study, we use the fifth wave of Indonesian
an impact on happiness but the number of friends in Family Life Survey, which is fielded between fall 2014
congregation. Hence, it is not proximity to God that and spring 2015, to address this issue. This data set is
derives happiness but the network of friendships that collected from a longitudinal household survey which
matters. Furthermore, Margetic (2005) revealed that contains 83% of Indonesian population living in 13 of 34
people in religion which motivate the internalization of provinces in the country. Differ from most studies which
values are less depressed than those who attend religious compares happiness between religious and non-religious
meetings due to obligation. Even, costly religious group, this research will be among the first which
immolation, such as fasting during Ramadhan month for concentrates on muslim individuals only in developing
muslim, can increase the happiness (Campante and countries. Even though a similar study has been
Yanagizawa-Drott, 2013). undertaken in Pakistan by Ismail and Desmukh (2012)
Hout and Greeley (2012) conjectures that religious with 65 men and 85 women as the sample with an age
people are happier through stronger belief and more range from 18 to 60 years, this study is different based on
frequent religious practices. Through his literature review, more diversified and larger sample as many as 12,759
Zuckerman (2009) draw conclusion that religious muslim individuals ranging from 14 to 91 years old. This
individuals performed better than nonreligious ones in study is not limited to specific group, such as muslim
terms of life satisfaction and well-being. In this case, students in Algeria (Tilouine and Belgoumidi, 2009) and
nonreligious individuals are generally less happier than muslim adolescents in Kuwait (Abdel-Khalek, 2007). This
religious ones. However, the tangible aspects of belonging research is also different from Migheli (2009) in the
to religion tend to reduce happiness through restrictions on context of muslim as a minority group in India, whereas it
behavior and consumption, whereas the spiritual aspects is a majority group in Indonesia.
increase it (Fidrmuc and Tunali, 2015). On the other hand, The objective of this study is to make further
a study from Opfinger (2010) found that happiness and contribution to knowledge by examining religious factors
religiosity are linked through a U-shaped pattern in which that boost happiness through the use of micro-level data as
high happiness levels are to those with lower religiosity most of previous studies used aggregate data to trace the
and higher religiosity. He concludes that atheists are relationship between religiosity and happiness. Since most
happier if they live in a society where religion does not literature in this matter has been dominated by western
matter, and so are the religious people living in a religious world subject to specific religion, such as christianity and
society. jewish, then it is important to extend this topic area to
Based on World Happiness Report published by muslim in a nation with different cultures and societies.
United Nations in 2017, international comparisons asserted Furthermore, the benefit of this study is expected to help
that secular countries with higher level of nonreligious the people who suffer from depression, through the role of
society reported the highest rank of happiness as compared
3
religion, in order to make them feel satisfied with their effect on dependent variable for any value of independent
own lives. variables. Third, a residual plot would demonstrate
The structure of this paper is organized as follows: In heteroskedasticty problem.
section 2, we introduce our data set and all the variables Logit and probit models solve the problems of linear
we employ in our model for empirical analysis. In section regression by fitting a nonlinear function to the data which
3, we discuss our results and in the last section, we considers the boundaries of dependent variable, enables
conclude and discuss our findings as well as suggestion for for different marginal effect, and solves heteroskedasticity
further research. problem. Unlike probit model which uses cumulative
distribution function of the standard normal distribution,
II. DATA AND METHODS
logit model uses cumulative distribution function of the
The analysis is based on questionnaire from the fifth logistic distribution. Hence, both functions will produce
wave of Indonesian Family Life Survey (IFLS-5) as any number to fall between 0 and 1 and can be
executed during 2014 to 2015. As dependent variable, our transformed to produce a predicted probability with similar
measure of happiness is based on subjective well-being (but not identical) inferences.
and obtained from this standard question:
III. RESULTS
“Taken all things together, how would you say things
are these days?” Since the dependent variable, happiness, ranges from
Based on the respondents’ response, the answers are 0 to 1 (binary), then we use probit and logit model to study
coded by 0 (unhappy) and 1 (happy). As independent the determinants of happiness based on religiosity and
variable, religiosity is measured by self reported of how socio-economic factors. The comparation of our probit and
religious they are as coded by 0 (not religious) and 1 logit regression is shown in Table 3.
(religious). We also consider participation in religious Basically, there is no significant difference between
activities as measured by how many times respondents our probit and logit estimation, and the results from both
pray each day and how often they participate in religious estimations seem to produce similar conclusion. Our
meeting in the past 12 months, ranging between 1 (never) regression reproduce a number of findings. Using the 1%
and 5 (very often). As for involvement in major religious level of significance, we can confirm that being religious
affiliation, we have information whether the respondents is more likely to be happy in both estimation. Its marginal
are Muhammadiyah, as coded by 1, or Nahdlatul Ulama effect is 0.034 which means that religious individual has
and others, as coded by 0. We also record whether the higher probability of being happy than those who are not
respondents have attended islamic school to distinguish by 0.034 (holding other explanatory variables constant at
them with those who have not acquired extensive islamic their average values). There is also strong evidence that
teaching in general school. attending to religious meetings more frequently is
In our model, we control for a wide range of socio- associated with higher probability of being happy. Its
economic characteristics: gender, age, marital status, and marginal effect suggests that the probability of being
income, in addition to religiosity. Gender is coded by 0 for happy rises by 0.007 as the attendance increases by one
female and 1 for male to distinguish the physical unit level. Even though there is different level of
characteristic of respondents. Age measures how old the significance in probit and logit estimation, we still can
respondent during the data collection. Marital status is conclude that more frequent prayer leads to higher
coded by 1 for formal marriage and 0 for others, consisting likelihood of being happy. Its marginal effect in both
of not married, separated, divorced, widow(er), and models assert that the probability of being happy increases
cohabitate. Income refers to total earnings of respondent in by 0.002 if the number of prayer increases by one. Hence,
the last 12 months. The basic statistics for each variable is our results suggest that the more religious the people, the
portrayed in Table 1. We also display inference statistics happier they are.
covering bi-variate analysis through correlation matrix for Nonetheless, having affiliated with islamic tradition
all variables in Table 2, and multivariate analysis through and education experience in islamic school do not seem to
logistic regression (logit) and probit model. These models have any impact on happiness. It implies that intensity of
are more suitable than linear regression when attempting religious attachment can increase happiness with no need
to model a dichotomous dependent variable. First, using to have experience in formal islamic teaching or
linear regression will lead to predictions outside the range participating in religious affiliation. Happiness of religious
of zero. Second, the functional form has the same marginal people comes from the intensity of their faiths, not from
formal doctrine associated with religious institution.
Hence, religious education through islamic institution 4
needs to be directed at positive psychology and preventive
counselling to deal with various life stressors so that it religious attitude and happiness across religions in
may result in greater wellbeing and happiness. Indonesia.
Our regression also contains a broad range of socio-
economic characteristics. For example, gender difference
does not seem to affect the respondent’ happiness, but it is V. REFERENCES
only statistically significant at 10% level on logit model [1] Abdel-Khalek, A. M. (2007). Religiosity, happiness,
that male has lower probability of being happy than health, and psychopathology in a probability
female. Meanwhile, age matters in determining happiness sample of Muslim adolescents. Mental Health,
since the older respondents, the less likely they are of Religion, and Culture, 10, 571-583.
being happy than those who are younger. Its marginal [2] Clark, A. & Lelkes, O. (2009): Let Us Pray: Religious
effect implies that each increase in age will lower the Interactions in Life Satisfaction, PSE Working
Papers 2009-01, PSE (Ecole normale supérieure).
probability of being happy by 0.003. The respondents with
[3] Campante, F., Yanagizawa-Drott, D., (2013), “Does
formal marriage statistically tend to be happier than those Religion Effect Economic Growth and
who are not since it provides them legal and social Happiness? Evidence from Ramadan”, Harvard
protection as well as division of burden in life. Even, its Kennedy School Faculty Research Working
marginal effect is the greatest among any other variables in Paper Series RWP13-052.
our model. We also conclude that respondents with higher [4] Ellison, C. & Gay, D. (1990): Region, Religious
Commitment, and Life Satisfaction Among Black
income are more likely to be happy. It means that income
Americans, in: The Sociological Quarterly, Vol.
is positively related to happiness, even in the context of 31/No. 1, 123-147.
muslim as our respondents. [5] Easterlin, R. A., (1995), “Will Raising the Incomes of
All Increase the Happiness of All?”, Journal of
IV. DISCUSSION
Economic Behavior and Organization 27(1), 35-
Our findings confirm the previous studies that 47.
religiousity increases happiness. It implies that religiosity [6] Gundlach, Opfinger. (2011). GIGA Research
Programme: Socio-Economic Challenges in the
comes from belief and the deeper it is, the stronger the
Context of Globalisation. religiosity as a
practice. When people feel the connection with God whom Determinant of Happiness.
they believe is merciful and almighty, this will help them [7] Greene, K. & Yoon, B. J. (2004): Religiosity,
to relax and more optimistic. Otherwise, the failure to Economics and Life satisfaction, in: Review of
surrender to God will result in misery. They will see that Social Economy, Vol. 70/No. 2, 245-262.
distressing events will not continue forever and have a [8] Hayo, B. (2007): Happiness in Transition: An
purpose. Having faith of God in Islam is considered a gift Empirical Study on Eastern Europe, in: Economic
Systems, Vol. 31/No. 2, 204-221.
that will help them to be patient and understanding.
[9] Hout, Michael, and Andrew M. Greeley. 2012.
Muslim individuals believe that God will help people and “Religion and Happiness.” Pp. 288-314 in Social
this belief create motivation to tackle the obstacles and Trends in American Life edited by Peter V.
survive during the bad times. Through regular prayer every Marsden. Princeton: Princeton University Press.
day, the communication with God is strengthened and men [10] Ismail, Desmukh, (2012). Religiosity and
are required to say their prayer together at the mosque on Psychological Well-Being. Vol.3 No. 11.
Friday. Saying the prayers in a group helps people to meet [11] Jan Fidrmuc, C. B. (2015). Happiness and Religion.
Economics and Finance Working Paper Series,
and talk and build social relationships. This will encourage
15-20.
individuals to avoid feelings of emptiness. Our findings [12] Mookerjee, R., Beron, K., (2005), “Gender, Religion
also suggest that socio-economic factors, such as age, and Happiness”, Journal of Socio Economics
marital status, and income, matter in determining 34(5), 674-685.
happiness of muslim individuals in Indonesia. [13] Migheli, Matteo. (2009). Religiosity and happiness:
For further research, we need to extend the study to an ever-winning couple? An answer from India.
Department of Public Policy and Public Choice.
other religions and estimate the separate regression for
[14] Margetic, B. (2005), Religiosity and health outcomes:
each religion in order to compare the relationship between review of literature: Coll.Antropol., v. 29, no. 1,
p. 365-371.
[15] Myers, D. G. (2008): Religion and Human
Flourishing, in: Eid, M./ Larsen, R. J. (Eds.): The
Science of Subjective Well-Being, New York:
Guilford Press, 323-346.
5
[16] Putnam, R. & Lim, C. (2009): Praying Alone Is No [19] Silberman, I. (2005): Religion as a Meaning System:
Fun: Religion, Social Networks, and Subjective Implications for the New Millennium, in: Journal
Well-being. Mimeo. of Social Issues, Vol. 61/No. 4, 641-663.
[17] Pollner, M. (1989): Divine Relations, Social [20] Tiliouine, H., & Belgoumidi, A. (2009). An
Relations, and Well-being, in: Journal of Health exploratory study of religiosity, meaning in life
and Social Behavior, Vol. 30/No. 1, 92-104. and subjective wellbeing in Muslim students from
[18] Steiner, Lasse ; Leinert, Lisa ; Frey, Bruno S.: Algeria. Applied Research in Quality of Life, 4,
Economics, religion and happiness. In: Zeitschrift 109-127.
für Wirtschafts- und Unternehmensethik 11
[21] Zuckerman, P. (2009). Atheism, secularity, and well-
(2010), 1, pp. 9-24. URN: http://nbn-
being: How the findings of social science counter
resolving.de/urn:nbn:de:0168-ssoar-348987.
negative stereotypes and assumptions. Sociology
Compass, 3(6), 49-971.
Appendices
Table 1
Descriptive Statistics
Table 2
Correlation
Happiness gender Age prayer religious affiliation married islamedu Income meetings
Happiness 1
Gender 0.0105 1
Age -0.1442 0.0209 1
-
Prayer 0.0146 0.1032 0.2277 1
-
Religious 0.0328 0.1116 0.2144 0.2821 1
- -
Affiliation -0.0007 0.0199 0.0004 0.0192 0.0033 1
Married 0.0999 0.1069 0.1856 0.0486 0.081 -0.0205 1
- -
Islamedu 0.0051 0.0153 0.0651 0.0575 0.0261 -0.0619 -0.0154 1
-
Income 0.0737 0.0999 0.0035 0.0237 -0.013 0.0356 0.0648 -0.0458 1
-
Meetings 0.0125 0.0122 0.2165 0.2173 0.1527 -0.0085 0.0634 0.0398 0.0104 1
6
Table 3
Probit and Logit Model with robust standard error
Probit Logit
Coef Marginal effects Coef Marginal effects
Cons 1.482*** 2.454***
(0.0732) (0.1417)
Gender -0.050 -0.006 -0.126* -0.009
(0.0370) (0.0050) (0.0735) (0.0051)
Age -0.023*** -0.003 -0.042*** -0.003
(0.0013) (0.0002) (0.0024) (0.0002)
Prayer 0.016*** 0.002 0.034* 0.002
(0.0091) (0.0009) (0.0199) (0.0010)
Religious 0.247*** 0.034 0.489*** 0.034
(0.0411) (0.0057) (0.0840) (0.0058)
Affiliation -0.013 -0.002 -0.032 -0.002
(0.0481) (0.0066) (0.0948) (0.0067)
Married 0.454*** 0.063 0.831*** 0.058
(0.0398) (0.0053) (0.0763) (0.0053)
Islamedu -0.035 -0.005 -0.079 -0.006
0.0640 (0.0089) (0.1278) (0.0090)
Income 0.012*** 0.002 0.031*** 0.002
(0.0023) (0.0002) (0.0047) (0.0002)
Meetings 0.051*** 0.007 0.096*** 0.007
(0.0135) (0.0019) (0.0267) (0.0019)
log likelihood -3287.231 -3284.901
LR chi2 642.46
Wald chi2 549.3
Pseudo R Square 0.088 0.089
Prob>Chi2 0.000 0.000
Standard errors in parentheses. Significance: ***p<0.01; **p<0.05; p<0.10.
Identification of Phosphatidylinositol-5-phosphate-
specific Binding Proteins Using Yeast Proteome
Microarrays and Non-quenched Fluorescent
Liposome
Samuel Herianto and Chien-Sheng Chen1)
1)
Department of Food Safety/Hygiene and Risk Management, College of Medicine, National Cheng Kung University, Tainan City 701,
Taiwan (R.O.C), e-mail: samuelhgmunthe@gmail.com.
Abstract ___All the biological functions are raised due to the joint For instance, 20-30% of genome of any organism codes
action of several biomolecules so-called interactions. Interaction of membrane protein [3, 4]. Lipids binding to membrane proteins
two biomolecules can provide functions that would not be possible not only protect cells but also flexibly modulate environmental
individually. These interactions also can be helpful to grasp many changing. The function of membrane proteins are belonged to the
molecular mechanisms behind the cellular process. There has long number of lipid bilayer surrounding its surface [5].
been highly interests to fulfill the need for systematic biochemical While protein-protein, protein-DNA, and protein-RNA have
screens of these interactions. While protein-protein, protein-DNA,
been widely studied, protein-lipid interaction are poorly
and protein-RNA have been widely studied, protein-lipid
understood and still require systematic investigation. Currently,
interactions are poorly understood and still require systematic
investigation. Protein microarrays and liposomes are one of the
about 60% of drug targets are cell surface compartments [6].
most powerful flat forms and tools to identify lipid-protein Each protein realizes individual lipid based on their specific
interactions. Non-quenched fluorescent (NQF) liposomes are bindings. In addition, lipid signaling contributes major role in
developed liposomes (spherical vesicles) that are surrounded by inflammation, cancer and metabolic disease [7]. Therefore,
phospholipid bilayers in which the lipid of interest can be investigation in protein-lipid interaction will support finding new
incorporated and can enhance the signal amplification instead of efficient therapeutic strategies and help to explain another
common liposome. Thus, NQF liposomes can be used to detect and biochemical process.
to analyze interactions between thousands of proteins and a small There have been 9 protein-lipid interactions methods
number of lipids with a single experiment simultaneously. occurred in these 2 decades, ranging from classical methods to
Phosphatidylinositol-5-phosphate (PI(5)P) is recognized as well- high throughput flat forms, such as: lipid pull-down [8], lipid-
established membrane-anchored regulatory molecules which is one overlay assay [9], protein microarrays [10, 11], liposome
of the phosphorylated derivatives of phosphatidylinositol with less microarray-based assay (LiMA) [12], living-cell imaging [13,
understood functions. Using this method, 23 PI (5) P-specific 14], ras rescue assay [15], caged lipids [16], affinity purification
binding proteins were identified and found to be involved in lipodomics [17, 18] and chemical engineering of lipids [19-21].
biochemical processes such as: transferase, transporter, DNA/RNA- However, protein microarrays came as the most powerful and
binding, GTPase, oxidoreductase, cytoskeleton, lyase, vacuolar
high throughput tool to study protein-lipid interactions among
sorting, activator, helicase and hydrolase and chaperon.
another methods [22].
Index terms___Yeast proteome microarrays, protein-lipid Proteome microarrays (protein chip) is a high-throughput
interactions, liposomes, phosphatidylinositol-5-phosphate
and efficient technique to study protein interactions, activities,
and functions [22]. Protein microarray is a miniaturized,
I. INTRODUCTION unbiased, and parallel platform, which contains thousands of
purified proteins in high-density format for analyzing a large
Lipid and proteins are very essential in their individual role in a number of proteins simultaneously in a single experiment [10,
living organism. Proteins have great diversity of functions ranging from 22]. A protein chip assay is usually prepared by immobilizing
catalyzing vital biological reactions to transporting nutrients [1], and proteins onto a glass slide using a standard contact spotter or non-
lipids have integral roles such as very essential in their individual role contact microarrayer . Thousands of purified proteins are
in a living organism. Proteins have great diversity of functions immobilized in a high-density format on a slide surface [10].
ranging from catalyzing vital biological reactions to transporting Protein microarrays for studying protein-lipid interaction
nutrients [1], and lipids have integral roles such asstoring energy or were initiated by Zhu (2001). Zhu et al. used five types of
being a major component of a membrane [2]. Despite their biotinylated liposomes from phosphoinositides group (PIs),
individual importance, interaction of these two molecules can
including phosphatidylinositol-3-phosphate (PI3P),
phosphatidylinositol-4-phosphate (PI4P), phosphatidylinositol
provide functions that would not be possible individually. This may
3,4-bisphosphate (PI(3,4)P2), phosphatidylinositol-4,5
be related to cell adhesion and communication, regulation of bisphosphate (PI(4,5)P2) and phosphatidylinositol-3,4,5
signaling, transport and metabolism, immune response, and other trisphosphate (PI(3,45)P3). 500 phosphoinositides-specific
biochemical complex processes [3]. proteins were identified on the yeast protein array that bound one
or another or the labeled liposomes.
Lu et al. (2012) [11] developed the liposomes to non- have allowed a simple method to detect lipid-protein interactions
quenched fluorescent (NQF) liposomes and succeeded in in a one-step experiment without the need for adding Cy3-
designing more direct and simpler methods without using biotin streptavidin when probing the yeast proteome chip. These both
and streptavidin to detect the binding. Sulfhorodamine B (SRB) reports demonstrated that liposome can be used as effective tool
and LRB-DPPE are used as the fluorescent dyes to encapsulate to generate good result when studying lipid-protein interactions.
the liposomes. As the result, 158 PI(3,5)P2-specific binding Basically, both Zhu and Lu have succeeded to apply protein
proteins were identified. This demonstrated that proteome microarrays and NQF liposome successfully as the most powerful
microarrays and NQF liposome can be used as effective tool to and promising tools to study lipid-protein interactions [10, 11].
generate good result in studying protein-lipid interactions. Totally, Due to its high throughput technology, protein microarrays is the
Zhu and Lu have succeeded to study protein-lipid interactions only flat form to study all kind of lipids faster than another
using 6 PIs group derivative. However, based on phosphorylation method. Based on LIPID MAPS, there are 8 lipid categories
by a variety of kinases, PIs have 7 derivative compounds including fatty acyls, glycerolipids, glycerophospholipids,
including PI(3)P, PI(4)P, PI(5)P, PI(3,4)P2, PI(3,5)P2, PI(4,5)P2 sphingolipids, sterol lipids, prenol lipids, saccharolipids and
and PI(3,4,5)P3 [23]. Among them, PI(5)P has not been observed polyketides. Each category contains subgroups. Among these,
and explored yet. Moreover, it is also one of the eight known glycerophospholipids, spingolipids and sterol lipids are the main
cellular phosphoinositide with less understood functions. component of cell membrane that are considered to interact with
Observation of PI(5)P-protein interactions can finish the story of proteins to accomplish their roles [26, 27]. Furthermore,
PIs and yield more information about the functions of this lipid according to our review, saccharolipids and polyketides are the
than can complete our data base. lipid category that have been observed at all by any methods.
However, both Zhu and Lu have studied lipid-protein
II. BASIC THEORIES interactions using phosphoinositide group (PIs) [10, 11]. PIs are
Proteome microarray is an array of entire proteins of a an important group of membrane phospholipids and include in
particular organism (contain thousands of purified proteins from glycerophospholipids category that are very abundant in cell
a particular organism). Zhu et al. [10] demonstrated the membrane [27]. They have been implicated in a wide variety of
construction and application of the proteome microarrays for the cell functions as second-messengers that regulate diverse cellular
first time. Yeast proteome microarrays that contained 85% processes, including growth, differentiation, cytoskeletal
(>5,800) individually purified proteins were used for several rearrangements, and membrane trafficking [28]. Based on
studies, including a lipid-proteome interaction study involving phosphorylation by a variety of kinases, PIs have 7 derivative
liposomes [10]. Liposomes are spherical vesicles surrounded by compounds [23]. While PI(3)P, PI(4)P, PI(3,4)P2, PI(3,5)P2,
phospholipid bilayers in which the lipid of interest can be PI(4,5)P2 and PI(3,4,5)P3 have been known to involved in many
incorporated [24]. Liposomes allow lipids to suspend in a buffer biological processes, PI(5)P has not been observed and explored
solution for proteome chip assays. yet.
The first history of protein microarrays for studying protein-
lipid interaction came from Zhu (2001). Zhu et al. made five III. METHODS
types of biotinylated liposomes with five kinds of lipids, A. Fabrication of NQF Liposome
including PI3P, PI4P, PI(3,4)P2, PI(4,5)P2 and PI(3,45)P3. Each All the chemicals including LRB-DPPE (Avanti Polar Lipids),
biotinylated liposome was constructed by containing DPPC (Avanti Polar), DPPG (Avanti Polar Lipids), cholesterol
phosphatidylcholine (PC) with 1% (w/w) Biotin DHPE (N- (Avanti Polar Lipids), PI5P (Avanti Polar Lipids) are placed into an
(Biotinoyl)-1,2-Dihexadecanoyl-sn-Glycero-3-Phosphoethanol- electronic desiccator for 15 minutes to remove moisture. All the
amine, and Triethyl- ammonium Salt) [10]. When probing with lipids were added into a 25 mL round-bottom flask as this amount:
the yeast proteome chip, Cy3-streptavidin was used to detect the LRB-DPPE 0.3% (0.004 µmole), DPPC 49.3% (0.657333 µmole),
biotinylated liposomes. As a result, through the liposomes, 500 DPPG 5% (0.066667 µmole), cholesterol 45% (0.6 µmole), PI5P
different proteins were identified on the yeast protein array that 0.4% (0.005333333 µmole). Vortex was used to make sure that they
bound one or another or the labeled liposomes. are mixed completely. 700 µL of 200 µM SRB was pre-warmed to
However, in 2012, Lu et al. [11] modified the liposomes to 60 °C in water bath. Organic solvents were evaporated by using N2
non-quenched fluorescent (NQF) liposomes and succeeded in gas to form lipid films. The pre-warmed 700 µL of
designing more direct and simpler methods. First, NQF liposomes 200 µM SRB 60oC was added into the ground flask that containing
were constructed with cholesterol, dipalmitoyl phosphatidylglycerol lipid films. The flask was vortexed until the lipid film is completely
(DPPG), dipalmitoyl phosphatidylcholine (DPPC), lissamine detached from the wall of the flask. Incubation was performed at
rhodamine B-dipalmitoyl phosphatidylethanol (LRB-DPPE), and 60°C in a water bath for 45 min. The 1 mL zeba desalt spin columns
PI(3,5)P2 as the lipid of interest [11, 25]. Sulfhorodamine B (SRB) (Thermo Scientific) then was prepared by washing it with 1 mL of
served as the fluorescent dye to encapsulate the liposome. Another TBS-sucrose for 3 times as company direction. A 50-nm-diameter
fluorescent dye, LRB-DPPE, was used to label liposomes with polycarbonate membrane (Whatman) and four membrane supports
fluorescence in the lipid bilayers. (Whatman) were pre-washed in TBS-Sucrose.
Interestingly, adding LRB-DPPE as a second fluorescent dye The mini-extruder was set up and tested by using TBS-
can produce stronger signal than having only SRB; in fact, LRB- sucrose. The NQF liposomes were extruded through a 50 nm
DPPE contributed the most to the fluorescent signals on the polycarbonate membrane for 30 times at 60°C. Separation of
membrane surface of liposome [11]. Therefore, this liposome liposome was conducted by adding the liposomes suspension to
contained two kinds of important fluorescent dyes (SRB as an obtain the center of a prewashed desalting spin column and
encapsulant and LRB-DPPE as labels) within the liposomal centrifuging the column at 1,000 rpm for 2 minutes to obtain the
bilayer, to provide signals directly. As the result, NQF liposomes purified liposomes. The purified liposomes were collected in an
Eppendorf tube and store it at 4°C.
2
.
B. Proteome Chip Assays
4 mL of blocking buffer was prepared and placed into a 4-well A B
box. 200 mL of TBST solution was also prepared in a
polypropylene box. Yeast proteome chips were taken from −80 ̊C
freezer quickly and immersed (face down) in the TBST solution
for 3 minutes (immersing the chip for 2 minutes without shaking,
then immersing it while shaking for 1 minute). Furthermore, the
chips were shaken gently (face up) for 2 minutes using orbital
shaker. The chips then were removed from the TBST solution
carefully and put in a 4-well containing blocking buffer and
incubated for 1 hour at RT with gentle shaking. NQF liposomes
were prepared by diluting it to 110 µL in TBS-sucrose in
Eppendorf tube. Flow cytometer was used to control the liposome
concentration. Then the chips were removed from the blocking
buffer by carefully grabbing the barcode end and probed with 110
µL of NQF liposomes containing PI5P and structural lipid only
(negative control). Both chips (PI5P and negative control) were
incubated simultaneously in a modified incubator for 80 minutes Fig. 1. Purification of NQF liposome using zeba spin column. Zeba spin
column separated liposomes from free fluorescent dyes by using size exclusion
at room temperature with very gentle shaking using a 3D shaker.
chromatography principle. Extruded liposomes were added into the column and
To remove the unbound liposomes, chips were washed using 1X- using centrifuge to fasten the separation. NQF liposomes were collected and while
TBS (pH=7.5) for 6 times. The chips were naturally dried in a the free fluorescent dye kept staying in the upper side of the column. (A) SRB
chemical drug shelf. The slides were then scanned with a Lux placed in column and (B) Liposomes placed in column.
Scanner (CapitalBio) to generate the tiff file. Zeba spin column works on principle of size exclusion
C. Hits and Databases Analysis chromatography. Liposomes which have bigger size than fluorescent
Binding signals (hits) were analyzed with the GenePix Pro 6.0 dye can fall down faster, while the fluorescent dyes such as SRB and
software. Tiff files were opened using GenePix and analyzed by LRB-DPPE which have smaller size will be trapped in the pore of
doing the alignment. Protein functions are retrieved from UniProt resin within the column. This could be one of the strong evident that
Knowledgebase (http://www.uniprot.org/uniprot/), and the liposomes have been separated from free fluorescent dyes
Saccharomyces Genome Database (http://www.yeastgenome.org). successfully. To fidelity of this separation process, we also
Protein family and domain architecture were obtained from the Pfam performed separation for SRB alone in the column (Fig.1A). As the
database (https://pfam.xfam.org/). result, the eluates collected did not contain any fluorescent dye
(fluorescent intensity is 0). By this, we convinced that liposomes
IV. RESULTS
separation can be conducted successfully.
A. Fabrication of NQF Liposome
(1) Purification of liposome: Fabrication of liposome was
initiated by phospholipids mixing, including: LRB-DPPE 0.3% NQF Liposome Free Fluorescent Dye
20000
(0.004 µmole), DPPC 49.3% (0.657333 µmole), DPPG 5%
(AU)
3
while free fluorescent dyes will be followed then. Both Fig. 1 and cleaner and has better possibility to analyze the hits for studying
Fig. 2 explained that liposomes and free fluorescent dyes have lipid-protein interactions. Furthermore, we used 50 nm
been separated successfully. polycarbonate filter membrane to fabricate the liposome.
(2) Size of liposome: Dynamic Light Scattering (DLS) was (3) Liposome concentration: Liposome fabrication will yield
used to measure the size of liposome. We provided the 2 types of the different liposome concentration, meanwhile we need to
liposomes: liposome using 50 nm and 200nm polycarbonate filter control the liposome concentration before probing it on the yeast
membrane. Liposome using 50 nm filter membrane can generate chip. We tried to test the instrument reproducibility for our
the smaller size of liposome than liposome using 200 nm filter sample (liposomes). We measured the concentration of some
membrane (Fig. 3). serial dilutions of liposome and found that they both have the
high correlation with R2 = 0.9997 (Fig. 5). We then chose 1,000
400 particles/µL as the standard concentration of liposome to probe
350 into yeast proteome chips.
300
size (nm)
on(particle
Liposomec
oncentrati
1200
s/µL)
250 291
y = 1118.2x + 0.3084
200 1000
R² = 0.9997
m
o
e
s
150
160 800
100
50 600
0
400
Liposome using 50 nm filter Liposome using 200 nm
membrane filter membrane
200
Sample
0
Fig. 3. The size of liposome using Dynamic Light Scattering (DLS). There are 0 0.2 0.4 0.6 0.8 1 1.2
2 liposomes. (a) Liposome using 50 nm filter membrane and (b) Liposome using
200 nm filter membrane. Serial dilutions of liposome
A Fig. 5. Dose response curve of liposome concentration for NQF liposome. The
fluorescent intensity of serial dilution of liposome was measure using ELISA reader to
see the correlation between liposome concentration and fluorescent intensity.
4
A
B
Negative Control PI5P
Fig. 6. A schematic representative of PI5P binding proteins using yeast proteome chips. (A) Yeast proteome chips containing of thousands of purified proteins
were probed with NQF liposomes and incubated for 80 minutes. Unbound liposomes were removed by using 1X TBS. After naturally drying, the chips were scanned
using Lux Scanner. (B) Image of yeast chip for negative control liposomes (left panel) and PI5P liposomes (right panel) for duplicate experiment.
C. PI5P-protein Interactions Using NQF Liposomes factor (6.7%), transferase (4.7%), oxidoreductase (4.0%),
By using the same methods, we first reported the previous result vacuolar transport (4.0%), cytoskeleton (2.7%), GTPase (2.0%),
from another reports. Five types of biotinylated liposomes with five phosphatase (2.0%) and ribosome (2.0%) [10]. In 2012, the
kinds of lipids, including PI(3)P, PI(4)P, PI(3,4)P2, PI(4,5)P2, and developed liposomes (NQF liposomes) containing PI(3,5)P2 lipid
PI(3,4,5)P3 were probed with yeast proteome chips were used to probe on yeast proteome chips [11]. 158 PI(3,5)P2-
[10]. Cy3-streptavidin was used to detect the biotinylated liposomes specific binding proteins were identified. These proteins were
binding proteins [10]. As a result, through the liposomes, 150 predicted to be ribosome (6.8%), oxidoreductase (6.8%),
phosphoinositide-binding proteins were identified on the yeast protein transferase (5.6%), transcription factor (3.7%), phosphatase
array that classified into kinase (14.1%), transcription (3.7%), kinase (3.7%), cytoskeleton (3.7%), and GTPase (2.5%)
5
[11]. However, these previous reports did not include PI5P that acids[32]. Lysine is basic amino acid that has main role to bind
we tried to observed and complete the phosphoinositiodes. Here with negatively charged PI5P. These results demonstrated that C2
we identified 23 PI5P-specific binding proteins that have been domain specifies Rsp5-dependent ubiquitination and suggest that
predicted to be involved in several biochemical processes Rsp5 function is regulated by PI5P (Fig. 8).
including: transferase (15%), transport (15%), DNA/RNA- Dus1 has role as oxidoreductase (Dihydrouridine synthase)
binding (8%), GTPase (7%), oxidoreductase (4%), cytoskeleton and member of a widespread family of conserved proteins
(4%), lyase (4%), vacuolar sorting (4%), chaperone (4%), including Smm1p, Dus3p, and Dus4p and can modifies pre-
activator (4%), helicase (4%) and hydrolase (4%) (Fig. 7). tRNA(Phe) at U17 [33].
To get a deeper understanding into the role of PI5P in cell We found 4 important transporter proteins including
regulation, 23 PI5P-specific binding proteins will be discussed. YKL091C, Erc1, Sec2 and Gdi1. For instance, YKL091C can
Rsp5 is an essential peripheral membrane protein that regulates the transfer a putative phosphatidylinositol/phosphatidylcholine and
internalization step of endocytosis and sorting from the secretory also possibly involved in lipid metabolism [34]. YKL091C maybe
pathway to the lysosome-like vacuole [29, 30]. Rsp5 also regulates recruits PI5P in these processes. While, Erc1 has pivotal role as
other processes including: MVB sorting, the heat shock response, drug transmembrane transporter. This protein has multi-drug and
transcription, endocytosis and ribosome stability[30]. Another report toxin extrusion (MATE) family that contains 581 amino acid
mentioned that it has main role in ubiquitination process. Rsp5 can residues (TABLE 1) [35]. MATE family is part of the
ubiquitinate Sec23p, Sna3p, Ste4p, Nfi1p, Rpo21p and Sem1p, multidrug/oligosaccharidyl-lipid/polysaccharide (MOP) exporter
autoubiquitinate and deubiquitinated by Ubp2p [31]. PI5P maybe is superfamily [36]. The yeast Erc1 protein mediates resistance to
involved in these regulation. Rsp5 has C2 domain that be recognized the methionine analogue, ethionine [37]. Ethionine is highly toxic
by PI5P to bind (Fig. 8 and TABLE 1). C2 domains bind to the and is a potent carcinogen. To do this role, possibly this protein
phosphoinositides through electrostatic interactions between basic need the PI5P to do this job. By this role, Erc1 is also called
amino acids and negatively charged lipids [32]. C2 domain has 88 protein detoxification 14.
amino acids and 11 of them are lysine amino
TABLE I.
IDENTIFIED PROTEINS THAT INTERACTED SPECIFICALLY WITH PI5P
Phosphoinositide
Systematic
No. Protein name recognition Another domain/family
name Function Annotation
domain/family
1 YER125W Rsp5 C2 domain WW domain Transferase
HECT-domain (ubiquitin-transferase)
2 YML080W Dus1 Dus Oxidoreductase (DihydroUridine Synthase)
3 YKL091C YKL091C CRAL/TRIO domain Phospholipid transport (transport)
4 YHR032W Erc1 MatE Drug transmembrane transporter (transport)
5 YLR150W Stm1 Stm1 DNA-binding
6 YER122C Glo3 Putative GTPase activating protein for Arf GTPase activator activity
7 YGL207W Spt16 Peptidase M24 Activator, Repressor
Histone chaperone Rttp106-like
FACT complex subunit (SPT16/CDC68)
8 YDL031W Dbp10 , DEAD/DEAH box helicase Helicase, Hydrolase, RNA-binding
Helicase conserved C-terminal domain
DBP10CT (NUC160) domain
9 YDR419W Rad30 ImpB/mucB/samB family Nucleotidytransferase (Transferase) and DNA-
binding
10 YNL272C Sec2 GDP/GTP exchange factor Sec2p, Essential for post-Golgi vesicle transport
11 YER136W Gdi1 GDP dissociation inhibitor GTPase activator activity and transport
12 YFR055W Irc7 Cys/Met metabolism PLP-dependent enzyme Lyase
13 YER128W Vfa1 AAA-ATPase Vps4-associated protein 1 Vacuolar sorting
14 YIR038C Gtt1 Glutathione S-transferase Trasnsferase
YNL116W Dma2 FHA Transferase
15 RING finger
16 YER048C Caj1 Dnaj domain Chaperone
X-domain of DnaJ-containing
17 YER071C Tda2 Tetex-1 family Associates with actin filaments (Cytoskeleton)
18 YER158C YER158C Unknown function
19 YBL012C YBL012C Unknown function
20 YCR020W-C YCR020W-C Unknown function
21 YBR060W YBR060W Unknown function
22 YDR010C YDR010C Unknown function
23 YGR126W YGR126W Unknown function
6
Activator Helicase Hydrolase Unknown function
Chaperon 4% 4% 4% 23%
4%
Transport
Vacuolar sorting
15%
4%
GTPase
7%
DNA/RNA-binding
8%
Lyase
Transferase
4% Cytoskeleton
15%
4%
Oxidoreductase
4%
Fig. 7. Functional Classification of PI5P-BDs. 23 specific bindings PI5P-BPs were retrieved from UniProt Knowledgebase (http://www.uniprot.org/uniprot/) and the
Saccharomyces Genome Database (http://www.yeastgenome.org) and classified into 13 functional classifications.
C2 domain of Rsp5
MPSSISVKLVAAESLYKRDVF
RSPDPFAVLTIDGYQTKSTSA
AKKTLNPYWNETFKFDDINE
NSILTIQVFDQKKFKKKDQGF
LGVVN
Sequence of C2 domain
Fig. 8. Structure of Rsp5. Rsp5 is essential peripheral membrane protein that has role in ubiquitination process. To do its function, Rsp5 is regulated by PI5P through
electrostatic interaction. C2 domain in Rsp5 has 11 lysine basic amino acids (positively charged, red color with abbreviation K) that bind with negatively charged PI5P
(head). Negatively charged PI5P comes from phosphate group that substituted with an inositol polar head group.
Sec2 is guanyl-nucleotide exchange factor for the small G- regulates vesicle traffic in secretory pathways by regulating the
protein Sec4p. It is also essential for post-Golgi vesicle transport dissociation of GDP from the Sec4/Ypt/rab family of GTP
and for autophagy and associates with the exocyst, via exocyst binding proteins [39].
subunit Sec15p, on secretory vesicles [38]. Gdi1 has another role Stm1 is activator and repressor protein that is required for
as GTPase activator and GDP dissociation inhibitor [39]. It also optimal translation under nutrient stress [40]. It also perturbs
7
association of Yef3p with ribosomes, involved in TOR signaling, be profiled by any lipids including PI5P. Of 23 PI5P-specific
binds G4 quadruplex and purine motif triplex nucleic acid [41], binding proteins, mostly proteins are transferase and transporter.
helps maintain telomere structure, protein abundance increases in Another role is DNA/RNA-binding, GTPase, chaperone,
response to DNA replication stress and serves as a ribosome oxidoreductase, cytoskeleton, lyase, vacuolar sorting, transporter,
preservation factor both during quiescence and recovery[42]. activator, helicase and hydrolase. Rsp5 is transferase protein that
Glo3 is ADP-ribosylation factor GTPase activating protein play vital role in ubiquitination process. To do its job, Rsp5
(ARF GAP) that involved in ER-Golgi transport [43]. While function is regulated by PI5P. Rsp5 is recognized to have C2
Spt16 is subunit of the heterodimeric FACT complex (Spt16p- domain that be bound to PI5P through electrostatic interactions
Pob3p) protein than has role as activator and repressor. Spt16 between basic amino acids of Rsp5 (lysine) and negatively
associates with chromatin via interaction with Nhp6Ap and charged PI5P [32].
Nhp6Bp [44], and reorganizes nucleosomes to facilitate access to A total of 6 PI5P-specific binding proteins were annotated to
DNA by RNA and DNA polymerases (specifically required for be “unknown function”. Similarly, the unknown function
diauxic shift-induced H2B deposition onto rDNA genes) [45] and proteins were also found in previous report. Zhu et al., found
co-regulates transcription with Mot1p through preinitiation 57.7% uncharacterized proteins [10] and meanwhile Lu et al.,
complex assembly and nucleosome organization [46]. had 59.9% uncharacterized proteins [11]. Yeast proteome that
Dbp10 is important protein as helicase, hydrolase and has not been systematically screened for binding property to PI5P
involves in RNA-binding. It is putative ATP-dependent RNA were recognized as the reason for that functionally
helicase of the DEAD-box protein family, constituent of 66S pre- uncharacterized proteins.
ribosomal particle, essential protein involved in ribosome
biogenesis [47]. ATP-binding RNA helicase involved in the VI. REFERENCES
biogenesis of 60S ribosomal subunits and is required for the 1. Berg, J.M., Biochemistry, revised edition. Chemical &
normal formation of 25S and 5.8S rRNAs [48]. Engineering News, 2001. 79(13): p. 130-130.
Rad30 is DNA polymerase and nucleotidytransferase that 2. Lehninger, A., Principles of biochemistry. 1982. 11(1).
involved in translesion synthesis during post-replication repair. It 3. Krogh, A., et al., Predicting transmembrane protein
also catalyzes the synthesis of DNA opposite cyclobutane topology with a hidden Markov model: application to
pyrimidine dimers and other lesions and involved in formation of complete genomes. J Mol Biol, 2001. 305(3): p. 567-80.
post-replicative damage-induced genome-wide cohesion [49]. 4. Babu, M., et al., Interaction landscape of membrane-protein
Another report mentioned that this protein may also have a role complexes in Saccharomyces cerevisiae. Nature, 2012.
in protection against mitochondrial mutagenesis [50]. 489(7417): p. 585-9.
Gtt1 and Dma2 are transferase protein. Gtt1 is another 5. Lee, A.G., Lipid-protein interactions in biological
tranferase protein that interact with PI5P. This ER associated membranes: a structural perspective. Biochim Biophys
glutathione S-transferase is capable of homodimerization, Acta, 2003. 1612(1): p. 1-40.
glutathione transferase for Yvc1p vacuolar cation channel [51]. 6. Overington, J.P., B. Al-Lazikani, and A.L. Hopkins, How
We also found that this protein has functional overlap with Gtt2p, many drug targets are there? Nat Rev Drug Discov, 2006.
Grx1p, and Grx2p [51]. Meanwhile, Dma2 is ubiquitin-protein 5(12): p. 993-6.
ligase (E3) that controls septin dynamics and spindle position 7. Wymann, M.P. and R. Schneiter, Lipid signalling in
checkpoint (SPOC) with ligase Dma1p by regulating recruitment disease. Nat Rev Mol Cell Biol, 2008. 9(2): p. 162-76.
of Elm1p to bud neck [52], regulates levels of eIF2 subunit 8. Zhang, P.B., et al., Proteomic identification of
Gcd11p, as well as abundance, localization, and ubiquitination of phosphatidylinositol (3,4,5) triphosphate-binding proteins
Cdk inhibitory kinase Swe1p [53]. This protein is ortholog of in Dictyostelium discoideum. Proceedings of the National
human RNF8 and similar to human Chfr [54]. Academy of Sciences of the United States of America,
Irc7 is beta-lyase involved in the production of thiols [55]. 2010. 107(26): p. 11829-11834.
Vfa1 [56] is protein that interacts with Vps4p and has a role in 9. Gallego, O., et al., A systematic screen for protein-lipid
vacuolar sorting and stimulates the ATPase activity of Vps4 and interactions in Saccharomyces cerevisiae. Molecular
localizes to endosomes in a Vps4-dependent manner [57]. Systems Biology, 2010. 6.
Caj1 is nuclear type II J heat shock protein of the E. coli 10. Zhu, H., et al., Global analysis of protein activities using
dnaJ family [58], contains a leucine zipper-like motif, binds to proteome chips. Science, 2001. 293(5537): p. 2101-2105.
non-native substrates for presentation to Ssa3p, may function 11. Lu, K.Y., et al., Profiling Lipid-protein Interactions Using
during protein translocation, assembly and disassembly [59]. Nonquenched Fluorescent Liposomal Nanovesicles and
Tda2 is protein that associates with actin filaments Proteome Microarrays. Molecular & Cellular Proteomics,
(cytoskeleton) [60], forms a complex with Aim21p that inhibits 2012. 11(11): p. 1177-1190.
barbed end F-actin assembly [60], elevates actin monomer pools 12. Vonkova, I., et al., Lipid Cooperativity as a General
to increase endocytotic efficiency and to regulate the distribution Membrane-Recruitment Principle for PH Domains. Cell
of actin between cables and patches [61]. Aim21p/Tda2p forms a Reports, 2015. 12(9): p. 1519-1530.
larger complex with actin capping proteins Cap1p and Cap2p 13. Surma, M.A., et al., A Lipid E-MAP Identifies Ubx2 as a
[61]. It is likely that PI5P regulated yeast cytoskeleton Critical Regulator of Lipid Saturation and Lipid Bilayer
organization in these all process. Stress. Molecular Cell, 2013. 51(4): p. 519-530.
14. Aguilar, P.S., et al., A plasma-membrane E-MAP reveals
V. CONCLUSIONS AND DISCUSSIONS links of the eisosome with sphingolipid metabolism and
Proteome microarray has showed and provided an excellent endosomal trafficking. Nature Structural & Molecular
membrane model for studying lipid-protein interactions that can Biology, 2010. 17(7): p. 901-U175.
8
15. Isakoff, S.J., et al., Identification and analysis of PH proteins of the sec14 superfamily. Molecular cell, 2008.
domain-containing targets of phosphatidylinositol 3-kinase 29(2): p. 191-206.
using a novel in vivo assay in yeast. Embo Journal, 1998. 35. Shiomi, N., et al., Improvement of S-adenosylmethionine
17(18): p. 5374-5387. production by integration of the ethionine-resistance gene
16. Subramanian, D., et al., Activation of membrane-permeant into chromosomes of the yeast Saccharomyces cerevisiae.
caged PtdIns(3)P induces endosomal fusion in cells. Nature Applied microbiology and biotechnology, 1995. 42(5): p.
Chemical Biology, 2010. 6(5): p. 324-326. 730-733.
17. Li, X.Y., et al., Extensive In Vivo Metabolite-Protein 36. Shiomi, N., et al., Production of S‐adenosyl‐L‐methionine by
Interactions Revealed by Large-Scale Systematic Analyses. Saccharomyces cerevisiae cells carrying a gene for ethionine
Cell, 2010. 143(4): p. 639-650. resistance. Biotechnology and bioengineering, 1990. 35(11):
18. Maeda, K., et al., Interactome map uncovers p. 1120-1124.
phosphatidylserine transport by oxysterol-binding proteins. 37. Hvorup, R.N., et al., The multidrug/oligosaccharidyl‐
Nature, 2013. 501(7466): p. 257-+. lipid/polysaccharide (MOP) exporter superfamily. European
19. Thiele, C., et al., Cholesterol binds to synaptophysin and is Journal of Biochemistry, 2003. 270(5): p. 799-813.
required for biogenesis of synaptic vesicles. Nature Cell 38. Walch-Solimena, C., R.N. Collins, and P.J. Novick, Sec2p
Biology, 2000. 2(1): p. 42-49. mediates nucleotide exchange on Sec4p and is involved in
20. Contreras, F.X., et al., Molecular recognition of a single polarized delivery of post-Golgi vesicles. The Journal of cell
sphingolipid species by a protein's transmembrane domain. biology, 1997. 137(7): p. 1495-1509.
Nature, 2012. 481(7382): p. 525-529. 39. Garrett, M., et al., GDI1 encodes a GDP dissociation
21. Hulce, J.J., et al., Proteome-wide mapping of cholesterol- inhibitor that plays an essential role in the yeast secretory
interacting proteins in mammalian cells. Nature Methods, pathway. The EMBO journal, 1994. 13(7): p. 1718-1728.
2013. 10(3): p. 259-264. 40. Van Dyke, N., J. Baby, and M.W. Van Dyke, Stm1p, a
22. Chen, C.S. and H. Zhu, Protein microarrays. Biotechniques, ribosome-associated protein, is important for protein synthesis
2006. 40(4): p. 423, 425, 427 passim. in Saccharomyces cerevisiae under nutritional stress
23. Thomas, L.M. and B.J. Holub, Regulation and Role of conditions. Journal of molecular biology, 2006. 358(4):
Phosphoinositide Phosphorylation in Human Platelets. p. 1023-1031.
Progress in Lipid Research, 1992. 31(4): p. 399-416. 41. Van Dyke, M.W., et al., Stm1p, a G4 quadruplex and
24. Chen, C.S., A.J. Baeumner, and R.A. Durst, Protein G- purine-motif triplex nucleic acid-binding protein, interacts
liposomal nanovesicles as universal reagents for with ribosomes and subtelomeric Y'DNA in Saccharomyces
immunoassays. Talanta, 2005. 67(1): p. 205-211. cerevisiae. Journal of Biological Chemistry, 2004.
25. Lu, K.Y., et al., Characterization of Lipid-Protein 42. Frantz, J.D. and W. Gilbert, A yeast gene product, G4p2, with
Interactions Using Nonquenched Fluorescent Liposomal a specific affinity for quadruplex nucleic acids. Journal of
Nanovesicles and Yeast Proteome Microarrays. Cold Spring Biological Chemistry, 1995. 270(16): p. 9413-9419.
Harb Protoc, 2016. 2016(10): p. pdb.prot087981. 43. Poon, P.P., et al., Retrograde transport from the yeast Golgi
26. Zhao, H.X. and P. Lappalainen, A simple guide to is mediated by two ARF GAP proteins with overlapping
biochemical approaches for analyzing protein-lipid function. The EMBO Journal, 1999. 18(3): p. 555-564.
interactions. Molecular Biology of the Cell, 2012. 23(15): p. 44. Wittmeyer, J., L. Joss, and T. Formosa, Spt16 and Pob3 of
2823-2830. Saccharomyces cerevisiae form an essential, abundant
27. van Meer, G., D.R. Voelker, and G.W. Feigenson, Membrane heterodimer that is nuclear, chromatin-associated, and
lipids: where they are and how they behave. Nature Reviews copurifies with DNA polymerase α. Biochemistry, 1999.
Molecular Cell Biology, 2008. 9(2): p. 112-124.
38(28): p. 8961-8971.
28. Emr, S.D., et al., Phosphoinositide lipid signaling in the
45. Mason, P.B. and K. Struhl, The FACT complex travels with
regulation of membrane trafficking and organelle identity.
elongating RNA polymerase II and is important for the
Faseb Journal, 2007. 21(5): p. A37-A37.
fidelity of transcriptional initiation in vivo. Molecular and
29. Galan, J.M. and R. Haguenauer‐Tsapis, Ubiquitin lys63 is cellular biology, 2003. 23(22): p. 8323-8333.
involved in ubiquitination of a yeast plasma membrane 46. Biswas, D., et al., The yeast FACT complex has a role in
protein. The EMBO journal, 1997. 16(19): p. 5847-5854. transcriptional initiation. Molecular and cellular biology,
30. Soetens, O., J.-O. De Craene, and B. André, Ubiquitin is 2005. 25(14): p. 5812-5822.
required for sorting to the vacuole of the yeast Gap1 47. HORSEY, E.W., et al., Role of the yeast Rrp1 protein in the
permease. Journal of Biological Chemistry, 2001. dynamics of pre-ribosome maturation. Rna, 2004. 10(5): p.
31. Huibregtse, J.M., et al., A family of proteins structurally and 813-827.
functionally related to the E6-AP ubiquitin-protein ligase. 48. Burger, F., M.-C. Daugeron, and P. Linder, Dbp10p, a
Proceedings of the National Academy of Sciences, 1995. putative RNA helicase from Saccharomyces cerevisiae, is
92(7): p. 2563-2567. required for ribosome biogenesis. Nucleic acids research,
32. Cho, W., Membrane targeting by C1 and C2 domains. 2000. 28(12): p. 2315-2323.
Journal of Biological Chemistry, 2001. 49. Vu, B., et al., DNA synthesis past a 5-methylC-containing cis-
33. Xing, F., et al., The specificities of four yeast dihydrouridine syn-cyclobutane pyrimidine dimer by yeast pol η is highly
synthases for cytoplasmic tRNAs. Journal of Biological nonmutagenic. Biochemistry, 2006. 45(30): p. 9327-9335.
Chemistry, 2004.
50. Xie, Z., et al., The p-benzoquinone DNA adducts derived
34. Schaaf, G., et al., Functional anatomy of phospholipid
from benzene are highly mutagenic. DNA repair, 2005.
binding and regulation of phosphoinositide homeostasis by
4(12): p. 1399-1409.
9
51. Choi, J.H., W. Lou, and A. Vancura, A novel membrane- microtubule interacting and trafficking (MIT) domain of
bound glutathione S-transferase functions in the stationary Vps4 and stimulates its ATPase activity. Journal of
phase of the yeast Saccharomyces cerevisiae. Journal of Biological Chemistry, 2014: p. jbc. M113. 532960.
Biological Chemistry, 1998. 273(45): p. 29915-29922. 57. Arlt, H., A. Perz, and C. Ungermann, An overexpression screen
52. Merlini, L., et al., Budding yeast dma proteins control septin in Saccharomyces cerevisiae identifies novel genes that affect
dynamics and the spindle position checkpoint by promoting endocytic protein trafficking. Traffic, 2011. 12(11):
the recruitment of the Elm1 kinase to the bud neck. PLoS p. 1592-1603.
genetics, 2012. 8(4): p. e1002670. 58. Hideyuki, M., et al., Isolation and characterization of CAJ1,
53. Bieganowski, P., et al., Cdc123 and checkpoint forkhead a novel yeast homolog of dnaJ. Gene, 1994. 145(1): p. 125-
associated with RING proteins control the cell cycle by 127.
controlling eIF2γ abundance. Journal of Biological 59. Walsh, P., et al., The J‐protein family: modulating protein
Chemistry, 2004. 279(43): p. 44656-44666. assembly, disassembly and translocation. EMBO reports,
54. Fraschini, R., et al., Functional characterization of Dma1 2004. 5(6): p. 567-571.
and Dma2, the budding yeast homologues of 60. Farrell, K.B., et al., Novel function of a dynein light chain in
Schizosaccharomyces pombe Dma1 and human Chfr. actin assembly during clathrin-mediated endocytosis. J Cell
Molecular biology of the cell, 2004. 15(8): p. 3796-3810. Biol, 2017: p. jcb. 201604123.
55. Roncoroni, M., et al., The yeast IRC7 gene encodes a β- 61. Shin, M., et al., Yeast Aim21/Tda2 both regulates free actin
lyase responsible for production of the varietal thiol 4- by reducing barbed end assembly and forms a complex with
mercapto-4-methylpentan-2-one in wine. Food Cap1/Cap2 to balance actin assembly between patches and
microbiology, 2011. 28(5): p. 926-935. cables. Molecular biology of the cell, 2018. 29(8): p. 923-
56. Vild, C.J. and Z. Xu, Vfa1 binds to the N-terminal 936.
10
1
Abstract—Rekonstruksi model tiga dimensi (3D) dapat Tujuan dari penelitian ini adalah untuk membangun 3D
digunakan untuk tujuan navigasi, dan aplikasi virtual reality. rekonstruksi sebuah bangunan dengan menggunakan gambar
Namun, saat ini model 3D juga digunakan sebagai upaya untuk panorama. Gambar panorama adalah gambar yang dihasilkan
mitigasi bencana seperti perencanaan evakuasi kebakaran dan dari beberapa foto yang overlap atau pertampalan sehingga
gempa bumi. Penelitian ini bertujuan untuk membentuk 3D dapat dilakukan proses jahitan antar foto membentuk
model bangunan menggunakan gambar panorama 720 derajat.
Penilaian akurasi menggunakan akurasi aerial triangulasi, pandangan 3600 secara horizontal dan 1800 secara vertikal.
akurasi digitasi sudut dan juga mengambil data terrestrial laser Penggunaan gambar panorama sangat efektif dan efisien
scanning (TLS) untuk membandingkan dan mengukur ground karena lebih cepat dan memiliki cakupan area yang lebih luas
control points (GCPs) menggunakan total station untuk analisa dibanding menggunakan gambar normal.
akurasi. Kamera Spherical Garmin VIRB 360 digunakan untuk
mengambil video pada 30 fps dengan ukuran gambar 3840 x II. DASAR TEORI
2178. Video yang sudah didapatkan akan di ekstrak ke dalam
bentuk gambar statis yang berurutan dengan interval 1.23 detik. A. Fotogrammetri Jarak Dekat
Gambar panorama yang sudah terbentuk diolah menggunakan Fotogrammetri terrestrial [4] merupakan cabang ilmu
Agisoft Photoscan Pro untuk pemodelan 3D. Penilaian akurasi fotogrammetri dengan meletakkan kamera pada permukaan
posisi menggunakan GCPs didalam Photoscan Pro. Hasil dense
point cloud akan di bandingkan dengan data TLS didalam
bumi. Kamera dapat dipegang dengan tangan, dipasang pada
software CloudCompare. Hasil penelitian yang pertama adalah kaki kamera atau dipasang pada menara ataupun dengan alat
akurasi posisi 3D (RMSE) setelah SfM adalah 18.9 cm, selain itu penyangga lain yang dirancang secara khusus. Istilah
perbedaan jarak 3D antara dense point cloud yang dihasilkan fotogrammetri rentang dekat pada umumnya digunakan untuk
dengan data TLS adalah 3.47 cm. Model rekonstruksi bangunan fotogrammetri terrestrial yang mempunyai rentang objek
didapatkan menggunakan point cloud dengan memproses sampai dengan 100 meter [1].
didalam Autodesk Revit sehingga dapat digunakan sebagai upaya Teknik ini memiliki kelebihan yaitu jika objek yang akan
untuk perencanaan mitigasi bencana. diukur sulit untuk dijangkau dan memiliki dimensi yang
sangat kecil, selaian itu metode ini juga memerlukan biaya
Kata Kunci—3D Model Rekonstruksi, Gambar Panorama, yang relatif lebih kecil dibandingkan dengan metode
Fotogrammetri Jarak Dekat.
fotogrammetri rentang jauh, karena jenis kamera yang
digunakan adalah dengan menggunakan kamera non metrik.
I. PENDAHULUAN Dalam bidang geodesi, metode fotogrammetri rentang dekat
Rekonstruksi dan konservasi merupakan langkah penting ini banyak dimanfaatkan karena dapat memberikan informasi
yang dapat dilakukan untuk upaya mitigasi bencana dari jarak, luas, volume.
banjir, gempa atau bencana yang lain yang sifatnya dapat Fotogrammetri rentang dekat banyak diaplikasikan dalam
merusak sebuah bangunan. Apalagi bangunan bersejarah atau berbagai bidang non topografi karena memiliki banyak
bangunan umum seperti kesehatan, pendidikan atau militer. keunggulan. Aplikasi yang berkembang antara laindalam
Oleh sebab itu perlu dilakukan rekontruksi, guna menjaga bidang arsitektur, arkeologi, forensik, medis, deformasi,
bangunan- bangunan tersebut agar tidak rusak dan hilang. industri dan lainnya.
Rekonstruksi tersebut biasanya mengacu pada dokumentasi
bangunan tersebut. Pendokumentasian tersebut tidak hanya B. 3D Rekonstruksi
terbatas untuk mengetahui dimensi geometri bangunan, namun Pemodelan adalah membentuk suatu bendabenda atau
juga terkait dengan seberapa besar perubahan dimensi obyek. Membuat dan mendesain obyek tersebut sehingga
geometri bangunan yang terjadi dalam kurun waktu tertentu terlihat seperti hidup. Sesuai dengan obyek dan basisnya,
Salah satu metode untuk melakukan rekonstruksi proses ini secara keseluruhan dikerjakan di komputer. Melalui
bangunan adalah dengan menggunakan metode konsep dan proses desain, keseluruhan obyek bisa
fotogrammetri. Metode ini mampu untuk merekonstruksi diperlihatkan secara 3 dimensi, sehingga banyak yang
sebuah bangunan dengan pemodelan bangunan secara 3 menyebut hasil ini sebagai pemodelan 3 dimensi (3D
dimensi selain itu dapat dianalisa dimensi geometri dan modelling) [2]. Ada beberapa aspek yang harus
akurasinya sehingga metode ini sangat sesuai untuk digunakan dipertimbangkan bila membangun model obyek, kesemuanya
dalam upaya mitigasi bencana. memberi kontribusi pada kualitas hasil akhir.
2
III. METHODE
A. Alat dan Material
Pada penelitian ini menggunakan dua macam perangkat
lunak yaitu Agisoft Photoscan Pro yang digunakan untuk
membuat modeling 3 dimensi dan mapping dan perangkat
lunak yang kedua adalah menggunakan Revit yang digunakan
untuk membuat model CAD. Kedua perangkat lunak tersebut
adalah berbayar (not open source). Sedangkan, alat yang Gambar 2. Lokasi penelitian
digunaakan untuk mendapatkan gambar panorama adalah
GARMIN VIRB 360 dengan spesifikasi seperti pada table 1. Pada gambar 3 dan 4 terdapat proses jahitan antara dua
foto karena kamera GARMIN memiliki dua sisi kamera yaitu
kamera depan dan kamera belakang sehingga proses jahitan
foto perlu dilakukan untuk mendapatkan foto panorama dari
dua foto tersebut. Perlu untuk menjadi pertimbangan dalam
pengambilan foto adalah kondisi cuaca. Cuaca yang paling
bagus untuk pengambilan foto adalah ketika cuaca cerah
dengan awan berwarna biru.
Tabel 1
Spesifikasi Kamera GARMIN VIRB 360
Gambar 3. Foto Panorama di Luar Bangunan
Spesifikasi Kamera GARMIN VIRB 360
C. Alur Penelitian
Adapun tahapan penelitian ini terbagi menjadi tiga bagian
utama. Pertama adalah melakukan pengumpulan data foto di
luar bangunan maupun di dalam bangunan gedung geomatika
serta melakukan pengumpulan referensi titik dan referensi
garis. Referensi ini digunakan untuk mengetahui akurasi dari
pemodelan yang akan dibuat. Untuk model luar bangunan
menggunakan referensi garis sedangkan model dalam
bangunan menggunakan referensi titik yang didapatkan dari
pengukuran total station (TS).
Setelah tahapan pertama dilakukan selanjutnya adalah Gambar 6. Point cloud kasar dengan lokasi kamera pada
tahapan kedua. Pada tahapan kedua ini, foto yang sudah model luar bangunan
didapatkan akan di proses menggunakan perangkat lunak
Photoscan Pro sesuai dengan gambar 5. Kemudian di dapatkan
dense point cloud. Sebelum mendapatkan dense point cloud,
proses yang dilakukan adalah membuat tanda referensi pada
setiap foto dan melakukan proses aerial triangulation untuk
menganalisa akurasi aerial triangulation, selanjutnya
melakukan dense image matching sehingga mendapatkan
dense point cloud atau data point cloud. Pada proses ini
terdapat banyak kumpulan titik-titik yang kurang berguna atau
banyak noise sehingga perlu dilakukan perbaikan point cloud.
Setelah point cloud sudah di perbaiki maka dapat di eksport ke
format file *.las. Hal ini untuk mempermudah proses konversi
format file di perangkat lunak Revit.
Ketiga, data point cloud yang sudah di konversi ke format
*.pcg dari format *.las maka dapat digunakan untuk membuat
model 3D CAD. Sebelum melakukan itu, pertama yang harus
dilakukan adalah digitasi 2D point cloud digunakan untuk
analisa akurasi digitasi sudut. Ketika sudah mendapatkan
akurasi sudut setiap corner maka 2D point cloud dapat
Gambar 7. Point cloud kasar dengan lokasi kamera pada
dilakukan perbaikan sesuai dengan sudut yang sebenarnya.
model dalam bangunan
Selanjutnya adalah melakukan digitasi dan labeling pada 3D
point cloud seperti pintu, jendela, lantai, platfon dan dinding.
Hasil tersebut didapatkan setelah melakukan proses aerial
triangulation. Untuk mendapatkan point cloud yang padat atau
dense point cloud maka dapat dilakukan dengan menggunakan
proses dense image matching sehingga mendapatkan point
cloud yang padat tetapi juga perlu melakukan perbaikan
dengan cara melakukan proses remove karena masih terdapat
noise pada point cloud tersebut.
Point cloud yang sudah diperbaiki terlihat seperti pada
gambar 8, 9 dan 10, dimana noise dari point cloud sudah
hilang dan point cloud terlihat padat. Setelah mendapat hasil
tersebut maka dapat melakukan analisa digitasi sudut setiap
cornernya.
Tabel 2
Referensi Titik pada Gambar Luar Bangunan
Untuk point cloud padat dalam bangunan memiliki bentuk Pada tabel 2 menunjukan bahwa kesalahan reprojeksi
bangunan yang sangat kompleks (lihat gambar 10) dengan sisi pada titik cek sebesar 21.4 pixels. Nilai ini sangat besar untuk
luar yang berwarna hitam atau gelap hal ini karena posisi kesalahan reprojeksi. Hal ini karena dipengaruhi oleh proses
kamera berada di dalam bangunan sehingga sisi luar bangunan algoritma penjahitan antar foto yang kurang sempurna dan
akan terlihat gelap jika dibandingkan dengan point cloud luar juga resolusi dari camera yang digunakan juga mempengaruhi
bangunan pada gambar 8 dan 9. reprojeksi.
Jika dibandingkan antara akurasi di dalam bangunan dan
luar bangunan maka didapatkan bahwa akurasi pada point
cloud dalam bangunan lebih tinggi dari pada point cloud luar
bangunan karena referensi yang digunakan juga berbeda
maksudnya pada point cloud dalam bangunan menggunakan
skala garis sedangkan point cloud luar bangunan
menggunakan referensi titik. Referensi titik diperoleh dari
pengukuran menggunakan TS dengan koordinat lokal.
C. Penilaian Akurasi Pada Digitasi Sudut
Akurasi digitasi sudut diperoleh setelah proses konversi
yang ada di perangkat lunak Revit. Pada gambar 11
menunjukan bahwa bentuk 2 dimensi pada luar bangunan
terlihat tidak simetri sehingga diperlukan perbaikan sebelum
melakukan digitasi 3 dimensi dan labeling.
16 87 90 -3
17 86 90 -4
18 98 90 8
Average 93.33 90 3.33
Min 79 -11
Max 105 15
Std.
9.23
Deviation
2 91.58 90 1.58
3 90.64 90 0.64
4 90 90 0
5 91.94 90 1.94
6 91 90 1
Min 90 0
Tabel 3
Akurasi Digitasi Sudut di Luar Bangunan D. Model Rekonstruksi 3 Dimensi
Model rekonstruksi yang diperoleh seperti pada gambar
Sudut yang Sudut
No.
diukur Sebenarnya
Selisih 14 dan 15 dibuat dari point cloud padat atau dense point
cloud didalam perangkat lunak Revit 2016. Adapun model
1 98 90 8
tersebut dibuat setelah proses perbaikan sudut di setiap
2 86 90 -4 corner sehingga model akan terlihat simetris dan sesuai
3 85 90 -5 dengan bentuk di lapangan. Untuk gambar 15, model CAD
dalam bangunan tidak mengalami perbaikan sudut di setiap
4 104 90 14 corner sebelumnya hal ini dikarena untuk mengetahui
5 103 90 13 perbedaan model CAD yang menggunakan perbaikan sudut
6 82 90 -8
dengan tanpa perbaikan sudut.
7 79 90 -11
8 102 90 12
9 79 90 -11
10 99 90 9
11 99 90 9
12 104 90 14
13 105 90 15
14 97 90 7
15 87 90 -3
Gambar 14. Model CAD luar bangunan
Hasil yang diperoleh dari perbandingan model tersebut
adalah lebih baik model CAD luar bangunan dari pada dalam
bangunan karena pada model CAD luar bangunan sudah
dilakukan perbaikan sudut. Kedua model CAD bangunan
tersebut memiliki beberapa label model seperti model pintu,
model tangga, model jendela, model lantai, model tangga,
model dinding dan model platfon atau rooftop.
Model ini yang akan dijadikan sebagai model tiga dimensi
dalam upaya mitigasi bencana. Maksudnya dengan adanya
model ini maka dapat melakukan simulasi jalur evakuasi serta
mengetahui kemampuan sebuah bangunan ketika terjadinya
bencana seperti gempa bumi maupun banjir.
V. KESIMPULAN
Adapun kesimpulan yang di dapat dari hasil dan
pembahasan adalah akurasi kedetilan geometri pada point
cloud sangat rendah, akurasi digitasi sudut pada model
didalam ruangan mempunyai hasil yang lebih baik dari pada
model di luar ruangan, akurasi aerial triangulation pada model
di luar ruangan mempunya hasil yang lebih baik dari pada
model didalam ruangan, dan terakhir adalah 3 dimensi dari
gambar panorama masih bisa digunakan ke banyak aplikasi
seperti pada bidang industry, mitigasi bencana dan atau
kesehatan.
Abstract—Cushion rear right seat merupakan komponen yang memiliki diameter lubang 6,8 mm dengan toleransi
berbahan dasar karet sintetis berjenis EPDM (Ethylene Propylene khusus lubang +0,2 mm. Terdapat dua tipe cushion RR seat
Diene Methylene) yang dipasang pada bagian bawah jok mobil yang digunakan yaitu tipe GB-6 dan tipe GB-7.Dasar Teori
TOYOTA varian terbaru. Permasalahan yang terjadi yaitu jumlah
Berikut Gbr.1 dari cushion RR seat tipe GB-6 dan GB-7.
hasil produksi yang seharusnya 1000 – 1200 buah per hari pada
kenyataannya hanya 600 buah per hari. Hal ini dikarena pada
proses finishing yang masih dikerjakan secara manual. Kegiatan
yang dilakukan pada proses finishing yaitu pemotongan flash hasil
sisa moulding dan pembuatan lubang baut pada cushion RR seat.
Dari permasalahan tersebut diperlukan suatu alat pemotong flash
bagian atas, flash bagian luar, flash yang menutupi ring, dan
pembuatan lubang baut pada cushion RR seat. Metode yang
dilakukan dalam penyelesaian masalah tersebut diantaranya
merencana, mengkonsep, merancang detail, dan mendokumentasi.
Dari kegiatan perancangan yang dilakukan dihasilkanlah
rancangan alat pemotong flash bagian atas, flash bagian luar,
flash yang menutupi ring, dan pembuatan lubang baut pada
cushion RR seat, dengan panjang alat yaitu 1540 mm, lebar 876
mm, dan tinggi 922 mm. Cara kerja alat ini yaitu secara otomatis
untuk pemotongan flash bagian atas, flash yang menutupi ring,
dan pembuatan lubang baut. Sedangkan pada pemotongan flash
bagian luar cara kerja alat yaitu secara semi otomatis. (a) (b)
Gbr. 1 (a) Cushion RR seat GB-6. (b) Cushion RR seat GB-7.
Index Terms— Perancangan, EPDM, pemotong, Cushion RR
seat, flash
I. PENDAHULUAN
Gesekan merupakan salah suatu fenomena yang
dipertimbangkan untuk mempertahankan suatu posisi tertentu
dari suatu benda atau objek terhadap penumpunya. Komponen
yang berfungsi untuk memberikan gesekan tersebut yaitu
bantalan. (a) (b)
Cushion rear right seat merupakan bantalan yang dipasang
pada bagian bawah jok mobil TOYOTA varian terbaru Gbr. 2 (a) Dimensi Cushion RR seat GB-6. (b) Dimensi ring
berbentuk kerucut terpancung berbahan dasar karet sintetis Cushion RR seat GB-6.
dengan jenis EPDM (Ethylene Propylene Diene Methylene)
Shore A 80 ±5 yang dihasilkan melalui proses moulding. Berikut Gbr. 2 dari ukuran cushion RR seat GB-6 dan ring
Sedangkan ring yang digunakan merupakan plat baja yang digunakan.
SPC270C TOYOTA cold rolled JIS steel dari hasil punch
2
TABEL 1
SHORE Durometer
(a) (b)
(4)
Di mana σb merupakan tegangan bending (N/mm2), Mb
adalah momen bending, dan Wb adalah axial section Gbr. 5 Diagram Benda Bebas (DBB) mengangkat
modulus . Persamaan momen bending berbeda-beda, beban
tergantung dari pembebanan yang terjadi.
4
(16)
Gbr. 6 Diagram Benda Bebas (DBB) menurunkan beban. 4. Diameter minimal poros pejal (ds)
T1=µ.W.R (11)
(17)
(12) TABEL 3
Faktor koreksi momen puntir (Kt)
T = T1 + T2 (13)
Beban yang didistribusikan Kt
Di mana RN adalah gaya normal, T1 adalahtorsi untuk
melawan gesekan, T2 adalah torsi untuk mengangkat beban T2’ Beban dikenakan secara halus 1
Beban dikenakan sedikit kejutan 1 – 1,5
adalah torsi untuk menurunkan beban, W adalah beban yang
Beban dikenakan dengan kejutan 1,5 – 3
diangkat, adalah sudut kemiringan ulir, adalah sudut gesek,
( = tan-1 ), d adalah diameter rata-rata dari power screw, dan R
TABEL 4
adalah rata-rata antara jari-jari luar dan dalam.
Faktor koreksi beban lentur (Cb)
K. Buckling
Buckling merupakan suatu fenomena di mana sebuah
struktur terjadi tekukan karena tidak dapat mempertahankan
5
III. METODE
(19)
Metode yang dilakukan dalam penyelesaian masalah
tersebut menggunakan metode perancangan Gerhard Pahl and
Apabila jenis kolomnya Tetmayer maka persamaannya
Wolfgang Beitz, metode tersebut diantaranya merencana
sebagai berikut.
(planning), mengkonsep (Concepual design), merancang
detail (embodiment design), dan mendokumentasi
σ (N/mm2)= 330 – (1,45 . λ) (20)
(Documentation).
Pada tahap merencana dilakukan pengumpulan data seperti
Dan apabila kolomnya EULER maka persamaannya sebagai
keinginan konsumen, analisa pasar, analisa existing product,
berikut:
analisa patent, dan dampak lingkungan. Keluaran dari tahap
merencana yaitu daftar tuntutan yang akan menjadi acuan
dalam mengkonsep dan merancang alat pemotong flash dan
(21) pembuat lubang baut pada cushion RR seat. Pada tahap
mengkonsep akan didefinisikan fungsi utama dan fungsi
Le adalah panjang efektif, r adalah jari-jari girasi, E adalah bagian dari alat yang akan dirancang. Setiap fungsi bagian
modulus elastisitas, dan I adalah inersia (mm4). akan dicarikan alternatif solusi. Alternatif solusi dari setiap
fungsi bagian kemudian digabung membentuk variasi konsep
L. Kekuatan Las rancangan. Selanjutnya adalah melakukan penilaian terhadap
variasi konsep untuk mendapatkan konsep rancangan yang
Kekuatan sambungan las sangat diperhitungkan terutama
terbaik berdasarkan kriteria yang ditentukan. Pada tahap
dalam mendesain rangka. Perhitungan pengelasan bergantung
merancang detail akan dilakukan pemodelan dan perhitungan
pada material kampuh las, throat, panjang las dan jenis las.
terhadap konsep yang terpilih terkait analisis gaya atau
Syarat suatu sambungan las dinyatakan kuat apabila tegangan
pembebanan yang terjadi dan melakukan penentuan
yang terjadi pada suatu konstruksi lebih kecil dari tegangan
komponen standar. Pada tahapan ini pun akan diperhitungkan
ijin dari kampuh las [7].
pemilihan material yang memenuhi kriteria sesuai rancangan
σt < σt, elektroda (22) alat yang akan dibuat. Pada tahap dokumentasi, rancangan
yang telah didetailkan akan diterjemahkan menjadi gambar
kerja dan bill of material.
σt adalah tegangan tarik yang terjadi. Kekuatan tarik setiap
elektroda berbeda-beda tergantung dari jenis klasifikasi
IV. HASIL PENELITIAN
elektroda itu sendiri. Dan pada setiap perhitungan kekuatan
las diberi nilai faktor keamaan tergantung dari jenis Hasil dari kegiatan merancang ini berupa gambar susunan,
sambungannya. Pada Tabel 5 ditunjukkan jenis sambungan diagram kelistrikan dan kontrol, bill of material, spesifikasi
beserta persamaannya. akhir alat, cara pengoprasian dan perawatan, dan prinsip kerja
alat.
A. Gambar susunan
Gambar susunan merupakan gambar secara keseluruhan
dari rancangan alat pemotongan flash bagian atas, flash bagian
luar, flash yang menutupi ring, dan pembuatan lubang baut
6
III. KESIMPULAN
Kesimpulan yang dapat diambil diantaranya
:
1. Perlunya mempertimbangkan kebutuhan dari alat yang
akan dibuat melalui pengumpulan data-data pada tahap
merencana. Sehingga konsep alat yang akan dibuat
mendekati kebutuhan atau fungsi alat tersebut ketika
dikembangkan menjadi rancang detail
2. Untuk mengembangkan konsep menjadi gambar detail,
perlu diperhitungkan terlebih dahulu gaya dan beban
yang akan terjadi ketika alat dibuat dan digunakan
nantinya. Agar tidak terjadi kegagalan desain.
3. Dalam merancang detail, sangat penting
mempertimbangkan komponen standar yang tersedia
dipasaran untuk meminimalisir biaya termasuk biaya
manufaktur dan waktu yang diperlukan untuk merakit
alat hasil rancangan. Selain itu pertimbangan-
pertimbangan tersebut pula akan berpengaruh pada
hasil akhir berupa gambar kerja atau dokumentasi alat.
Abstract—Gedung Rawat Inap RSUD Goeteng, Purbalingga, tanah di seluruh Indonesia [4]. Perubahan peraturan ini
Indonesia yang dibangun pada tahun 2012 merupakan bangunan memicu banyak dilakukan studi mengenai pengaruh
dengan kategori risiko IV. Akibat konfigurasi struktur yang perubahan peraturan terhadap besarnya gaya gempa yang
tidak beraturan, gedung ini memiliki kerentanan terhadap
terjadi dan dampaknya terhadap kinerja struktur bangunan.
gempa yang cukup besar. Kajian ini bertujuan untuk
mengevaluasi kinerja sesimik Gedung Rawat Inap RSUD Salah satu kajian yang telah dilakukan oleh Arfiadi dan
Goeteng yang dilakukan dengan analisis beban dorong Satyarno [5] yang membahas tentang perbandingan spektrum
(pushover). Hasil kajian menunjukkan gaya geser dasar yang desain beberapa kota besar di Indonesia dalam SNI 03-1726-
diterima Gedung Rawat Inap RSUD Goeteng adalah sebesar 2012 [6] dan SNI 1726: 2002 [7], menyebutkan bahwa untuk
10064,421 kN dan 5655,626 kN masing-masing untuk arah X dan kota-kota yang mengalami kenaikan spektrum desain, baik pada
arah Y. Daktilitas stuktur untuk arah X dan arah Y masing- periode pendek (yang mempengaruhi gedung sekitar 2 sampai 8
masing adalah 2,74 dan 4,46. Rasio simpangan struktur yang lantai) maupun perioda 1 detik (yang mempengaruhi gedung 10
terjadi di bawah 1%, masing-masing adalah 0,17% untuk arah X
dan 0,24% untuk arah Y. Dengan demikian kinerja seismik
lantai atau lebih), maka gedung-gedung di kota-kota tersebut
Gedung Rawat Inap RSUD Goeteng dikategorikan pada taraf perlu dievaluasi ketahanannya terhadap gempa, terutama
Immediate Occupancy dimana diprediksi tidak terdapat seperti rumah sakit dan bangunan penting lainnya.
kerusakan yang berarti pada struktur, kekuatan dan Berdasarkan peta hazard gempa Indonesia [8], untuk jenis
kekakuannya kira-kira hampir sama dengan kondisi sebelum situs tanah berupa batuan, Purbalingga memiliki percepatan
gempa. Komponen nonstruktur masih berada ditempatnya dan respon spektrum pada periode pendek, 0,2 detik, (Ss) sebesar
sebagian besar masih berfungsi jika utilitasnya tersedia. Gedung
dapat tetap berfungsi dan tidak terganggu dengan masalah
0,760g dan percepatan respon spektrum pada peirode 1 detik,
perbaikan. (S1) sebesar 0,311g seperti dapat dilihat pada Gambar 1.
Dengan demikian Purbalingga merupakan wilayah dengan
Index Terms—Daktiltas, gaya geser dasar, gempa bumi, potensi kegempaan cukup tinggi karena memiliki percepatan
kinerja seismik, pushover respon spektrum pada periode pendek, 0,2 detik, (Ss) lebih
tinggi atau setara 0,5g tetapi lebih rendah dari 1,0g dan
I. PENDAHULUAN percepatan respon spektrum pada peirode 1 detik, (S1) lebih
Gedung Rawat Inap RSUD Goeteng, Purbalingga yang disajikan pada Gambar 3. Model tiga dimensi dapat
dibangun pada tahun 2012 merupakan bangunan dengan dilihat pada Gambar 4.
kategori risiko IV dan memiliki konfigurasi struktur yang
tidak beraturaan. Perilaku bangunan selama terjadinya gempa
tergantung pada beberapa faktor, termasuk apakah bentuknya
sederhana dan simetris. Bangunan yang memiliki
ketidakberaturan baik vertikal maupun horizontal lebih rentan
terhadap gempa [2]. Beberapa bangunan bahkan dapat
berperilaku sangat jelek saat dilanda gempa bumi disebabkan
oleh bentuk bangunan yang tidak beraturan [10]. Kajian ini
bertujuan untuk mengevaluasi kinerja seismik Gedung Rawat
Inap RSUD Goeteng, Purbalingga yang dilakukan dengan
analisis beban dorong (pushover).
Kharwar dan Lhonde [11] berpendapat bahwa terdapat
tingkatan analisis struktur yang sesuai untuk analisis struktur
berbasis kinerja. Setiap prosedur tingkat yang lebih tinggi
merupakan metode yang lebih akurat dalam menentukan
kinerja sebenarnya dari bangunan akibat beban gempa, tetapi
membutuhkan upaya yang lebih besar dalam hal persiapan
data, waktu dan komputasi. Analisis pushover merupakan
metode yang populer direkomendasikan untuk mengevaluasi
kinerja struktur baik yang telah lama berdiri maupun yang
baru [12] karena kesederhanaannya [13]. Analisis pushover
dapat menyediakan informasi yang memadai tentang seismic
demand yang dikenakan oleh design ground motion pada
sistem struktur dan komponen-komponennya. Bangunan yang
telah ada dapat dikategorikan tidak memadai secara
kegempaan dikarenakan persyaratan peraturan kegempaan
yang terus ditingkatkan di samping adanya kemajuan dalam
pengetahuan di bidang engineering.
II. METODE
A. Pemodelan Struktur
Data spesifikasi gedung:
Gbr. 2. Denah struktur Gedung Rawat Inap RSUD Goeteng, Purbalingga
Fungsi Bangunan : Rumah Sakit
Material : Baja ST37, Beton K-275
Atap : Baja ringan dengan penutup genteng
Tebal Plat : 120 mm
Kolom Lantai 1 : 0,45 m x 0,45 m
Kolom Lantai 2 : 0,30 m x 0,30 m
Balok : (dimensi balok disajikan pada Tabel 1)
TABEL I
DIMENSI BALOK
Gbr. 3. Model tiga dimensi Gedung Rawat Inap RSUD Goeteng, Purbalingga
B. Analisis Pushover
Analisis pushover merupakan suatu performance based
evaluation yang bertujuan untuk menentukan kapasitas suatu
struktur. Pada dasarnya, analisis pushover dilakukan dengan
memberikan beban lateral yang nilainya ditingkatkan
berangsur-angsur (incremental) secara proposional pada
struktur hingga mencapai target displacement atau mencapai
mekanisme di ambang keruntuhan karena terjadinya sendi
plastis pada elemen balok maupun kolom. Prosedur
analisisnya menjelaskan bagaimana mengidentifikasi elemen-
elemen struktur yang akan mengalami kegagalan terlebih Gbr. 5. Matriks taraf kinerja struktur [15]
dahulu. Seiring dengan peningkatan beban terda[at elemen-
elemen yang mengalami leleh dan deformasi inelastic yang
Berdasarkan FEMA 451 [14] dan ATC 40 [16], kinerja
mengakibatkan berkurangnya kekakuan struktur. Dengan
seismik struktur dikategorikan menjadi taraf Operational,
analisis pushover, karakteristik hubungan gaya-perpindahan
Immediate Occupancy, Life Safety, dan Collapse Prevention.
non linier dapat ditentukan yang secara tipikal ditunjukkan
Pada taraf Operational tidak terjadi kerusakan berarti baik
pada Gambar 4.
pada struktur maupun non struktur bangunan, atau bangunan
masih dapat tetap berfungsi. Taraf Immediate Ocupancy
mengindikasikan bahwa setelah terjadi gempa struktur tidak
mengalami kerusakan yang berarti, kekuatan dan kekakuannya
kira-kira hampir sama dengan kondisi sebelum gempa.
Komponen nonstruktur masih berada ditempatnya dan
sebagian besar masih berfungsi jika utilitasnya tersedia.
Bangunan dapat tetap berfungsi dan tidak terganggu dengan
masalah perbaikan. Pada taraf Life Safety terjadi keruntuhan
struktur saat gempa terjadi tetapi bangunan tidak sampai
runtuh, komponen non struktural sudah tidak berfungsi tetapi
masih bisa digunakan kembali setelah adanya perbaikan. Taraf
collapse prevention bermakna terdapat kerusakan yang berarti
Gbr. 4. Karakteristik hubungan gaya-perpindahan [14] baik pada komponen struktur maupun non struktur, dimana
kondisi bangunan sudah hampir runtuh akibat berkurangnya
Gambar 4 di atas memperlihatkan bahwa respon linier kekuatan dan kekakuan struktur. Ilustrasi kinerja seismik
dimulai dari titik A (unloaded component) dan kelelehan bangunan dapat dilihat pada Gambar 6.
mulai terjadi pada titik B. Respon dari titik B ke titik C
merupakan respon elastis plastis. Titik C merupakan titik yang
menunjukkan kekuatan nominal, dan nilai absisnya yang
merupakan deformasi menunjukkan dimulainya degradasi
kekuatan elemen struktur (garis C-D). Pada titik D, respon
struktur secara substansial mengalami pengurangan kekuatan
menuju titik E. Untuk deformasi yang lebih besar dari titik E,
kekuatan elemen struktur menjadi nol.
C. Kinerja Struktur
Struktur yang dievaluasi pada kajian ini merupakan
bangunan Rumah Sakit maka kinerja yang disyaratkan adalah
pada taraf Immediate Occupancy. Kinerja seismik suatu
struktur dapat dilakukan dengan membandingkan kapasitas Gbr. 6. Ilustrasi kinerja seismik bangunan [14]
4
IV. KESIMPULAN
Dari kajian yang telah dilakukan dapat disimpulkan bahwa
gaya geser dasar yang diterima Gedung Rawat Inap RSUD
Goeteng adalah sebesar 10064,421 kN dan 5655,626 kN
masing-masing untuk arah X dan arah Y. Daktilitas stuktur
untuk arah X dan arah Y masing-masing adalah 2,74 dan 4,46.
Gbr. 7. Titik kinerja Gedung Rawat Inap RSUD Goeteng arah X dan arah Y Rasio simpangan struktur yang terjadi di bawah 1%, masing-
TABEL 2
masing adalah 0,17% untuk arah X dan 0,24% untuk arah Y.
HASIL ANALISIS PUSHOVER Dengan demikian kinerja seismik Gedung Rawat Inap RSUD
Goeteng dikategorikan pada taraf Immediate Occupancy
Parameter Arah X Arah Y
dimana diprediksi tidak terdapat kerusakan yang berarti pada
V (kN) 10064,421 5655,626 struktur, kekuatan dan kekakuannya kira-kira hampir sama
D (m) 0,00712 0,01000 dengan kondisi sebelum gempa. Komponen nonstruktur masih
Sa 0,352 0,275
berada ditempatnya dan sebagian besar masih berfungsi jika
Sd 0,00383 0,00485
utilitasnya tersedia. Gedung dapat tetap berfungsi dan tidak
Teff 0,204 0,258
terganggu dengan masalah perbaikan.
βeff 0,061 0,112
5
Abstract - Masjid Agung Kotagede adalah salah satu dilakukan menggunakan Terrestrial Laser
Masjid tertua di Yogyakarta dan termasuk salah Scanner.
satu bangunan herritage yang senantiasa harus Akuisisi data menggunakan metode laser
terjaga keaslian dan kelestariannya. Penggunaan scanning akan lebih efisien dan efektif karena
teknologi yang tepat guna dan tepat sasaran akan mampu menghasilkan data ukuran dengan tingkat
membuat usaha menjaga kelestarian bangunan kerapatan yang tinggi, namun terdapat kesulitan
herritage menjadi lebih mudah dan lebih efisien. dalam akuisisi data bagian atap bangunan karena
Dari berbagai pilihan yang tersedia, teknologi TLS harus berdiri diatas permukaan atap dimana
geospasial merupakan salah satu pilihan yang kondisi tersebut sulit untuk dilakukan. Hal ini
terbaik. Teknologi geospasial terkait dengan menyebabkan data ukuran menjadi tidak utuh dan
dokumentasi keruangan, dimana salah satu bentuk sempurna.
dokumentasinya dapat dilakukan dengan pemetaan Akuisisi data menggunakan UAV based
secara 3D. Hasil dari pemetaan ini adalah sebuah photogrametry mampu memodelkan obyek dari
dokumen 3D bangunan herritage secara detail, sisi atas dengan tingkat kerapatan yang tinggi
akurat dan teliti. Salah satu metode pemetaan tergantung spesifikasi kamera dan tinggi terbang.
tersebut adalah dengan menggunakan Laser Dengan melakukan pemotretan dari udara, maka
Scanning dan UAV (unmanned aerial vehicle). obyek bangunan dapat terpetakan dengan baik
Dengan kombinasi dua data ini, obyek herritage khususnya pada bagian atas atau atap bangunan.
dapat dipetakan secara utuh dengan tingkat Kombinasi antara kedua metode ini mampu untuk
kedetailan dan akurasi yang tinggi. Model 3D ini memodelkan obyek bangunan dengan utuh, mulai
sebagai data dokumentasi digital yang realistik dan dari dasar bangunan hingga bagian atap dengan
akurat sehingga bisa digunakan oleh pihak detail, lengkap dan realistik.
pengambil keputusan dan pembuat kebijakan untuk Penelitian ini dilakukan pada objek cagar
merencanakan dan melestarikan bangunan budaya berupa bangunan yaitu Komplek Masjid
herritage dengan lebih cepat dan komprehensif. Agung Kotagede. Masjid tersebut berada di
selatan kawasan Pasar Kotagede, Banguntapan,
Index Terms - Masjid Kotagede, TLS, UAV, 3D
Bantul, Yogyakarta. Masjid Agung Kotagede
model.
merupakan masjid tertua di Yogyakarta dan
menjadi objek cagar budaya yang terbentuk dari
I. PENDAHULUAN adaptasi budaya agama islam dengan agama hindu
dan budha. Kombinasi data TLS-UAV yang
Pemodelan 3D dapat dilakukan dengan
dilakukan adalah dengan mengambil data
berbagai metode, seperti metode fotogrametri
bangunan sisi bawah menggunakan TLS dan
maupun dengan metode laser scanning.
pengambilan data atap bangunan masjid
Pengambilan data menggunakan metode
menggunakan UAV jenis multicopter DJI
fotogrametri dapat menggunakan kamera digital
Phantom 4. Dari kombinasi data point cloud
yang terpasang pada wahana UAV atau pesawat
TLS-UAV tersebut dapat dibentuk Model 3D
komersil, sedangkan pengambilan data
Komplek Masjid Agung Mataram Kotagede
menggunakan metode laser scanning dapat
1
secara utuh dan dengan tingkat kedetailan yang ukuran yang akurat. Model 3D dibagi menjadi 3
tinggi. kategori, antara lain:
II. DASAR TEORI
a. Solid
A. Bangunan Bersejarah/Cagar Budaya Model solid 3D merupakan bentuk
visualisasi 3D dengan menggabungkan
Warisan budaya dibagi dalam beberapa bentuk objek primitif seperti kubus, bola,
kategori cagar budaya yaitu warisan budaya silinder. Pembuatan model solid dalam
berupa benda (nyata) dan warisan budaya tak bentuk yang lain dapat dilakukan melalui
benda [12]. Warisan budaya benda meliputi operasi gabungan (union), irisan
warisan budaya bergerak (contoh: lukisan, naskah, (intersect), dan selisih (different). Model
koin, patung), warisan budaya tidak bergerak solid dapat digunakan untuk menghitung
(contoh:monumen, situs arkeologi,bangunan volume, massa, ukuran objek, dan
bersejarah lainnya), dan warisan budaya bawah momen inersia objek. Pembentukan
air (contoh:bangkai kapal, reruntuhan dan kota model 3D suatu objek dengan
bawah air). Sedangkan warisan budaya tak benda menggunakan model solid memerlukan
antara lain tradisi, seni pertunjukan, dan ritual. operasi yang rumit.
Menurut Undang-Undang No 10 tahun 2010 b. Surface model
cagar budaya merupakan warisan budaya baik Surface model adalah tipe model 3D
berupa benda, bangunan, struktur, situs, dan yang tidak memiliki ketebalan.
kawasan di darat dan atau di air yang perlu Perbedaan antara Surface model dan
dilestarikan keberadaannya karena memiliki nilai solid model adalah solid model mampu
penting bagi sejarah, ilmu pengetahuan, memberikan informasi tentang massa,
pendidikan, agama, dan atau kebudayaan melalui sedangkan surface model tidak bisa.
proses penetapan. Bangunan cagar budaya Surface model mampu mewakili bentuk
merupakan salah satu warisan budaya yang dari permukaan objek. Pada beberapa
terbuat dari benda alam dan atau benda buatan kasus, pemodelan objek yang memiliki
manusia untuk memenuhi kebutuhan ruang bentuk yang rumit dapat lebih mudah
berdinding dan atau tidak berdinding serta beratap. dilakukan dengan menggunakan surface
Sesuai undang-undang tersebut, bangunan dapat model dibandingkan menggunakan solid
diusulkan sebagai bangunan cagar budaya jika model.
memenuhi beberapa kriteria antara lain berusia c. Mesh
50 tahun atau lebih, memiliki arti khusus bagi Mesh merupakan sebuah model jaring
sejarah, ilmu pengetahuan, pendidikan, agama, segitiga yang dibentuk dari kumpulan
dan atau kebudayaaan, serta memiliki nilai budaya titik. Kualitas bentuk model 3D yang
bagi penguatan kepribadian bangsa. dibentuk oleh mesh dipengaruhi oleh
Berdasarkan pengertian tersebut, Masjid kerapatan dan banyaknya data titik yang
Kotagede memenuhi kriteria sebagai bangunan tersedia. Model mesh dibentuk dengan
cagar budaya. Masjid Kotagede mewakili salah cara menghubungkan titik-titik yang
satu sejarah, agama, dan budaya daerah pada masa saling berdekatan sehingga membentuk
lampau sehingga perlu mendapatkan perhatian suatu jaring segitiga. Mesh mampu
khusus. merepresentasikan bentuk permukaan 3D
B. Pemodelan 3D secara baik. Mesh memiliki kemampuan
untuk mengatur kehalusan ataupun
Pemodelan yaitu mendesain dan membuat objek kondisi sebenarnya dari objek yang
atau suatu benda terlihat seperti nyata sesuai objek dimodelkan. Kualitas mesh
dunia nyata [7]. Objek tersebut terlihat nyata di merepresentasikan objek dengan baik
computer yaitu terlihat 3 dimensi sehingga proses tergantung pada kerapatan titik yang
tersebut disebut pemodelan 3D. 3D modelling menyusunnya.
adalah proses merepresentasikan suatu objek pada Selain bentuk diatas, model 3D dapat
dunia nyata kedalam bentuk digital. Proses 3D direpresentasikan dalam bentuk primitif 3D.
modelling menghasilkan produk berupa model 3D. Objek primitif tersebut yaitu kubus, balok, bola,
Model 3D secara keseluruhan merupakan inovasi silinder, limas, prismma, dan kerucut.
dari teknologi komputer grafik. Model 3D yang Obyek-obyek bangunan herritage dapat didekati
baik adalah model 3D yang mampu dan dimodelkan dalam bentuk primitif 3D.
merepresentasikan bentuk suatu objek menyerupai
objek sebenarnya secara detil dan memiliki C. Terrestrial Laser Scanner
2
Quintero, dkk [14] menyebutkan bahwa (Quintero et al., 2008)
laser scanning mendeskripsikan suatu permukaan d = ½(c x t)
objek menggunakan teknologi laser. Metode ini Keterangan:
menganalisa lingkungan objek atau real world d= jarak scanner ke objek
melalui akuisisi data dari bentuk dan c= kecepatan rambat sinar laser (3 x 108 m/s)
kemungkinan kenampakan yang ada pada suatu t= waktu tempuh sinar laser pergi dan kembali
objek di permukaan bumi yaitu warna. Namun
warna hasil akuisisi data tidak sesuai dengan Pemindaian berbasis fase (phase based)
warna aslinya karena warna yang didapatkan menggunakan sinar energi laser konstan yang
merupakan intensitas pantulan dari objek. Data dipancarkan dari pemindai. Pemindai kemudian
akuisisi kemudian digunakan untuk mengukur pergeseran fasa energi laser kembali
merekonstruksi objek secara digital baik berupa untuk menghitung jarak. Pemindai berbasis fase
model 2D atau 3D yang dapat digunakan untuk dapat memperoleh data dengan laju lebih dari satu
berbagai macam aplikasi. Laser scanning juta poin per detik. Namun jangkauan phase based
memiliki keunggulan yaitu TLS dapat merekam terbatas hingga sekitar 80 meter. Pemindai berbasis
data point dalam jumlah yang banyak dengan fase sebagian besar cocok untuk pekerjaan pabrik
akurasi tinggi dalam waktu yang singkat. Namun industri dan bangunan interior.
untuk mendapatkan cakupan lengkap struktur E. Registrasi Data Terrestrial Laser Scanner
diperlukan beberapa kali scanning karena TLS
termasuk dalam line of sight instrument. Pada umumnya objek yang dilakukan
Teknologi laser scanner dikategorikan scanning terlalu besar untuk dapat dicakup hanya
menjadi dua yaitu statis dan dinamis. Saat posisi dengan satu kali berdiri alat. Oleh karena itu,
scanner berada pada posisi tetap saat akuisisi, biasanya untuk mencakup seluruh objek dilakukan
maka termasuk dalam kategori statis. Keuntungan scanning dari beberapa posisi berdiri alat.
kategori ini adalah data hasil akuisisi memiliki Masing-masing posisi scan dideinisikan dari
tingkat presisi dan kerapatan titik yang tinggi. sistem koordinat scanner. Untuk menyelaraskan
Sedangkan pada kategori dinamis scanner posisi scanner yang berbeda-beda, diperlukan
melekat pada wahana bergerak. Pada kasus ini posisi dan orientasi yang tetap dari sistem
dibutuhkan sistem tambahan untuk mengetahui koordinat scanner sesuai koordinat sistem
posisi wahana seperti menambahkan INS dan lokal/global [14].
GPS sehingga lebih kompleks dan mahal. Contoh
penerapan laser scanner dinamis yaitu airborne
laser scanning dan scanning menggunakan UAV.
3
Gbr. II.3. Teknik Registrasi Terestrial Laser Scanner (Sumber : masing-masing point clouds dan titik tersebut
Quintero et al., 2008)
tidak akan pernah sama untuk masing masing
scene world seperti gambar II.6 [14].
Registrasi target to target menggunakan
target buatan dengan permukaan geometris
misalnya printed paper target, silinder dan sphere
yang diletakkan pada bagian overlap dari kedua
data yang akan diregistrasi. Distribusi target
buatan tersebut diletakkan saat akuisisi data di
lapangan sehingga terlihat pada data hasil point
cloud pada masing-masing posisi scan (scene
world). Pada area yang sulit dijangkau untuk
meletakkan target buatan, dapat digunakan target
alami seperti pojok jendela, atau hiasan tembok Gbr. II.6. Registrasi cloud to cloud antara dua scene world
(Sumber : Reshetyuk, 2009)
jika yang discan adalah suatu bangunan [14].
Metode target to target dilakukan dengan
Penyatuan pointcloud dilakukan dengan
terlebih dahulu menentukan 6 parameter diantara
kedua koordinat sistem [10] seperti gambar II.4. terlebih dahulu menjadikan salah satu pointcloud
menjadi acuan kemudian membawa pointcloud
yang lain ke acuan tersebut dengan proses iterasi
sehingga menyerupai bentuk dan geometri objek
[8]. Penggabungan data TLS dan UAV dilakukan
dengan menggunakan prinsip registrasi cloud to
cloud. Dengan menggunakan metode ini, data
pointclouds hasil perekaman TLS dan hasil
ekstraksi UAV dapat digabungkan menjadi satu
sistem untuk kemudian dilakukan proses
pemodelan 3D.
4
dilengkapi dengan sensor kamera 1/2.3” CMOS TLS dibandingkan dengan point cloud UAV yang
(total pixel 12.76 M), lensa FOV 94 ̊ 20 mm tampak lebih halus. Perbedaan antara point cloud
(f/2.8), serta dilengkapi system positioning TLS dengan point cloud UAV termasuk rendah
GPS/GLONASS [4] seperti gambar II.7. dan berada di jangkauan sentimeter pada area
yang permukaannya homogen, seperti dinding.
Perbedaan yang besar antara kedua data point
cloud dapat disebabkan karena kurangnya data
point cloud atau dalam beberapa kasus adanya
penskalaan atau pengukuran yang salah.
Xu, Z, dkk [16] melakukan penelitian
mengenai pembuatan model 3D dari objek
Gbr. II.7. DJI Phantom 3 Professional (DJI, 2018)
bangunan bersejarah berdasarkan video UAV dan
data TLS. Data UAV yang berupa video akan
Sensor Complementary Metal Oxide
Semiconductor (CMOS) dapat meredam noise, diubah terlebih dahulu menjadi data frame foto
lebih efisien, serta menggunakan daya yang lebih yang selanjutnya diolah menjadi data point cloud.
rendah dibanding sensor Charge-Coupled Devices Penelitian ini menunjukkan bahwa kombinasi data
(CCD). Selain itu, pada sensor CMOS, sinyal point cloud UAV dan point cloud TLS terintegrasi
muatan gambar dibaca satu baris pada satu waktu dan dapat dilakukan proses digitalisasi, namun
seperti mngakses memori secara acak dengan ada beberapa hal yang perlu diperhatikan yaitu
menggunakan baris dan kolom terpilih sehingga mengenai perbedaan kepadatan point cloud TLS
memungkinkan pembacaan berkecepatan tinggi dan UAV. Point cloud yang dihasilkan dari data
dengan konsumsi daya rendah [5]. UAV mempunyai kepadatan yang lebih jarang
daripada point cloud TLS. Hal tersebut dapat
II.1. Tujuan Penelitian diantisipasi dengan meningkatkan kepadatan point
cloud saat mengolah data foto UAV.
Tujuan dari penelitian ini adalah
mengkombinasikan data point cloud TLS dan data
point cloud UAV menjadi satu sistem yang III. METODOLOGI
digunakan untuk pemodelan 3D secara utuh mulai A. Bahan Penelitian
dari dasar bangunan hingga bagian atas/atap pada
Bahan yang dipakai dalam penelitian ini
obyek bangunan herritage.
yaitu:
1. Data scan world menggunakan TLS Faro
II.2. Tinjauan Pustaka Focus3D X330 dilakukan pada tanggal 21
Integrasi data point cloud TLS dan point Juli 2018 yang menghasilkan 13 scan world.
cloud UAV pernah dilakukan oleh Zhihua Xu, dkk 2. Data foto udara menggunakan UAV
[15] dengan hasil akhir berupa model 3D Multicopter DJI Phantom 3 Pro dilakukan
bangunan bersejarah. Penelitian tersebut pada tanggal 21 Juli 2018 yang menghasilkan
menggunakan point cloud TLS pada bagian fasad 375 foto.
bangunan dan point cloud UAV pada bagian atap
bangunan. Penelitian ini menyebutkan bahwa B. Peralatan Penelitian
kedua data point cloud (TLS dan UAV) dapat
1. Perangkat keras
diregistrasi dengan baik dengan metode iteratif,
Perangkat keras yang digunakan dalam
sehingga model 3D yang dihasilkan memiliki penelitian ini adalah: TLS Faro Focus3D
cakupan yang lengkap dan detail yang mendalam. X330 (1 unit), UAV DJI Phantom 3 Pro (1
Penelitian ini juga menunjukkan bahwa data dari unit), Statif (1 buah) dan perangkat komputer.
metode scanning dan rekonstruksi foto dapat 2. Perangkat lunak
saling melengkapi dalam hal cakupan, resolusi Perangkat lunak yang digunakan dalam
penginderaan, dan akurasi model untuk penelitian ini adalah:
membentuk rekaman dan model 3D berkualitas a. Maptek i-Site Studio 6.1 untuk registrasi
tinggi. data TLS dan menggabungkan data
Penelitian yang mengkombinasikan point TLS-UAV.
cloud dari dari TLS dan UAV juga dilakukan oleh b. Agisoft Photoscan Professional 1.2.5
G.J. Grenzdorffer [6]. Penelitian ini menunjukkan untuk mengolah data foto udara UAV.
bahwa pada struktur yang lebih kecil (detail) c. Leica Cyclone 6.0 untuk filterisasi data
direpresentasikan lebih baik oleh data point cloud dan pemodelan 3D.
5
C. Tahapan Penelitian di lapangan. Posisi berdiri alat harus
mempertimbangkan area overlap antar scan
Penelitian ini terdiri dari dua tahap yang
meliputi tahap persiapan dan tahap pelaksanaan world untuk mempermudah registrasi data.
yang digambarkan seperti diagram alir pada
Gambar III.1 berikut.
2. Pengolahan data
Pengolahan data pada penelitian ini terdiri
dari:
Gbr. III.1. Diagram alir penelitian 1. Registrasi Data TLS
Registrasi data TLS dilakukan
D. Tahap Persiapan menggunakan perangkat lunak Maptek
Tahap persiapan meliputi survei i-Site Studio 6.1 dengan metode cloud to
pendahuluan. Survei pendahuluan adalah tahapan cloud. Metode ini menjadikan salah satu
untuk menentukan langkah akuisisi data scan world menjadi scan world acuan dari
menggunakan TLS dan UAV. Survei pendahuluan seluruh scan world yang ada. Pada
dilakukan dengan melihat struktur dan desain penelitian ini, scan 3 dijadikan sebagai
objek sehingga dapat ditentukan lokasi scan world acuan atau dijadikan sebagai
pengambilan data menggunakan TLS. Pada tahap “fixed reference” dan scan world lainnya
ini juga dilakukan pembuatan jalur terbang UAV dijadikan sebagai “data to register”.
dengan mempertimbangkan situasi, kondisi, dan Registrasi pertama menggunakan metode
bentuk keseluruhan objek dari atas sehingga data Automated Initial Positioning yakni
yang dihasilkan dapat maksimal. registrasi otomatis antar scan world tanpa
menggunakan informasi sensor hanya
translasi dan rotasi. Hasil dari tahap
E. Tahap Pelaksanaan registrasi awal terkadang masih terdapat
Tahap kedua adalah tahap pelaksanaan “gap” atau selisih antar scan world
yang meliputi pengumpulan data dan proses sehingga perlu dilakukan registrasi kedua
pengolahan data. menggunakan metode Global Registration.
1. Pengumpulan data Metode Global Registration adalah metode
registrasi yang dapat meregistrasi banyak
Pengumpulan data meliputi akuisisi data
scan world secara langsung sehingga nilai
menggunakan TLS dan UAV TLS akan
RMS registrasi yang dihasilkan kecil.
melakukan pemindaian / scanning dengan
laser yang bergantung dari berdiri alat. Posisi
berdiri alat ini akan menjadi jumlah dari scan 2. Pengolahan Data Foto Udara UAV
world yang dihasilkan saat pengambilan data Pengolahan data UAV dilakukan
6
menggunakan perangkat lunak Agisoft
Photoscan Professional 1.2.5. Pengolahan
data foto udara akan melalui beberapa
proses hingga dapat menghasilkan data
point cloud.
a. Align Photo
Align Photo bertujuan untuk
menentukan posisi kamera dan
orientasi pada setiap foto yang Gbr. III.4. Data point cloud hasil pengolahan data foto
digunakan serta membentuk model udara UAV
point cloud awal.
b. Build Dense Cloud
Setelah proses align photo, dilakukan
proses pembuatan dense cloud yaitu
proses pembentukan dan visualisasi
point cloud berdasarkan perhitungan
perkiraan posisi kamera secara
mendalam.
c. Build Mesh
Proses selanjutnya adalah pembentukan
mesh dengan memilih build mesh
dalam menu workflow. Pembuatan
Gbr. III.5. Hasil kombinasi data point cloud TLS-UAV
mesh tergantung pada parameter
surface type, source data, face count,
4. Pemodelan 3D
interpolation, dan point classes.
Pemodelan 3D dari data point could yang
d. Export Point cloud
sudah bergabung dilakukan pada perangkat lunak
Setelah proses pembentukan mesh
Leica Cyclone 6.0. Pemodelan dilakukan pada
sudah selesai, point cloud dapat di
struktur bagian fasad bangunan hingga pembuatan
export agar dapat dilakukan proses
atap dengan metode pemodelan primitif.
selanjutnya.
Pembuatan model 3D menggunakan fitur insert
3. Penggabungan Data Point Cloud TLS dan object pada perangkat lunak Leica Cyclone. Objek
UAV yang dominan digunakan adalah objek box dalam
Proses penggabungan data point cloud TLS pembuatan struktur Masjid Agung Kotagede.
dan point cloud UAV dilakukan di Pemberian warna juga dilakukan untuk
perangkat lunak Maptek i-Site Studio. Pada membedakan setiap bagian dari bagunan tersebut.
proses ini, dilakukan penggabungan point Pemberian warna dilakukan dengan
cloud bagian fasad bangunan yang berasal menggunakan fitur edit color/material. Detil
dari point cloud TLS, sedangkan bagian obyek pada bangunan masjid dapat didekati
atap bangunan menggunakan point cloud dengan bentuk-bentuk geometri sederhana seperti
hasil pengolahan foto udara UAV. kubus, balok, silinder, dsb.
7
model primitif dan mampu menghasilkan
model 3D yang akurat, realistik dan detail,
serta mendekati bentuk kondisi nyata/real.
8
[11] Sarinurrohman, “Pemodelan Tiga Dimensi M.D., Poelman, R., Hankar, M., Barnes, S.,
Objek dengan Bentuk Geometris Sederhana Caner, H., Budei, L., Heine, E., Reiner, H.,
Menggunakan Teknik Fotogrametri Jarak Garcia, J.L.L., Taronger, J.M.B, 3D Risk
Dekat,” Skripsi, Jurusan Teknik Geodesi Mapping. Theory and practice on Terrestrial
Fakultas Teknik Universitas Gadjah Mada, Laser Scanning, 2008.
Yogyakarta, 2005. [15] Xu, Z., Wu, L., Shen, Y., Li, F., Wang, Q.,
[12] UNESCO, Ilicit Trafficking of Cultural Wang, R., “Tridimensional Recontruction
Property. Applied to Cultural Heritage with the Use of
http://www.unesco.org/new/en/culture/theme Camera-Equipped and Terrestrial Laser
s/illicit-trafficking-of-cultural-property/unesc Scanner,” Remote Sensing ISSN 2072-4292,
o-database-of-national-cultural-heritage-laws/ China, 2014.
frequently-asked-questions/definition-of-the- [16] Xu, Z., Wu, T.H., Shen, Y., Wu, L., “Three
cultural-heritage/ diakses pada tanggal 25 Dimensional Reconstruction of Large
September 2018, 12.15. Cultural Heritage Object Based on UAV
[13] UNESCO, Undang-Undang Republik Video and TLS Data,” The International
Indonesia nomor 11 Tahun 2010 tentang Archives of the Photogrammetry, Remote
Cagar Budaya Sensing and Spatial Information Sciences
http://www.unesco.org/culture/natlaws/media volume XLI-B5, XXIII ISPRS Congress,
/pdf/indonesie/ind_act11_10_clther_indorof Czech Republic, 2016.
diakses pada tanggal 25 September 2018,
13.19. [17] Eisenbei, H., "UAV Photogrammetry,"
[14] Quintero, M.S., Genechten, B.V., Bruyne, Disertasi, ETH Zurich, Zurich, 2009.
Biography Penulis
Ruli Andaru, Dosen dan Peneliti di Departemen Teknik Geodesi FT UGM. Menekuni bidang Laser Scanning dan UAV untuk
keperluan 3D Building dan disaster sejak 2010. Sekarang sedang melanjutkan Studi Doktoral di NCKU Taiwan bidang Geomatics
Engineering.
9
Derivative Compound of 2,6-Dimethyl-1,4-
Benzoquinone as Potential Anticancer Drugs:
Synthesis, Molecular Studies, and Octanol –
Water Solubility Test
Rizki Rachmad Saputra1,Siti Mariyah Ulfa1*,Hideki Okamoto2
1
Department of Chemistry, Faculty of Mathematic and Natural Sciences, University of Brawijaya, Malang,
INDONESIA
2
Division of Chemistry and Biochemistry, Graduate School of Natural Science and Technology, Okayama
University, Tsushima-Naka 3-1-1, Kitaku Okayama, 700-8530, JAPAN
*Corresponding authors: ulfa.ms@ub.ac.id
Abstract—Thymoquinone is the largest constituent in the triglicoside, and glucoside5,6. Analysis of essential oil of black
essential oil of black cumin seeds (Nigella sativa). The main cumin showed the compound of α-pinene, limonene, p-cimen,
structure in thymoquinone is quinoid ring that can be modified carvakrole, carvone, trans-anetol, and thymoquinone7,8.
to increase the bioavailability as a drug candidate. In this
Thymoquinone is bioactive constituent of black cumin seeds
research, the modifications were carried out by the addition of
alkyl chains as many as four, seven, and ten carbons (C4, C7 and essential oil of 54%9.
C10) by bromoalkylation reaction. The FTIR spectra of alkylation Thymoquinone showed significant activity as an anti-
product has a C-Br bond at ~687 cm-1. 1H-NMR and 13C-NMR neoplastic against human pancreatic adenocarcinoma, uterine
spectra showed that the alkylation product formed were 2-(4- sarcoma, leukemia cells, and minimize toxic to normal
bromobutyl)-3.5-dimethyl-1,4-benzoquinone, 2-(7-bromoheptyl)- cells10. Thymoquinone anti-oxidant effect inhibited
3,5-dimethyl-1,4-benzoquinone, and 2-(10-bromodecyl)-3.5-
inflammation in animal models and cell culture systems11.
dimethyl-1,4-benzoquinone, were successfully synthesized in
74.72 %, 11.97 %, and 26.67 % yield. LCMS spectra showed Thymoquinone has been shown to provide an anti-
molecular weight of products C4, C7, and C10 in 271.05 g/mol, inflammatory, anti-oxidant and anti-neoplastic properties, both
313.69 g/mol, dan 355.84 g/mol. We evaluated its potency as in vitro and in vivo, 9.
drugs by molecular docking using CYP3A4 as receptor. Most of the research on thymoquinone has demonstrated its
Derivatives of thymoquinone (C4, C7, C10) showed Ki of 20.15; potential as anticancer, however its application hindered by
4.92; 2.79 µM, and IC50 of 10.92; 3.08; 1.98 ppm, respectively.
several factors. First, thymoquinone has low solubility in
Free energy Gibbs (ΔG˚) derivative compound is -5.44; -6.41; -
7.58 kcal/mol. Then, we have investigated its properties by aqueous media (high hydrophobicity); this caused
solubility test in octanol – water. Solubility test results showed bioavailability problems. Second, its high lipophilicity caused
that the products C4, C7, and C10 had greater solubility in its lower activity to be a drug. Finally, thymoquinone is
octanol phase than in the water phase. Based on the data sensitive to temperature and light, that limits the increase in its
obtained from HPLC, thymoquinone partition coefficient was bioavailability12. A potent drug candidate should have high
2.58. Furthermore, C4, C7, and C10 had partition coefficients of
lipophilicity properties; that helps a drug entering organs and
1.6; 4.95; 1.74. Our results suggest that derivative of
thymoquinone (C4, C7, C10) could as potential drugs for reaching drug receptors in order to provide biological effects.
anticancer therapy to induce CYP3A4 and be needed more Modification of the chemical structure can be a strategy to
clinical investigation to know activity in body system) increase lipophilicity of a ligand or a drug candidate13. In a
previous study, Antonenko, et al. (2008), thymoquinone has
Index Terms— thymoquinone, benzoquinone, alkylation, in been modified its chemical structure by lengthening the alkyl
silico, inhibition constant, IC50, in vitro, partition coefficient, free chains, and resulted in its effect as anti-oxidants in the
energy Gibbs
mitochondria14.
The basic material used is 2,6-dimethyl-1,4-benzokuinon
I. INTRODUCTION
modified by extending the alkyl chains (C4, C7, and C10).
The utilizing of natural medicines in Indonesia from year to The nature of the bioavailability of the compounds
year was increasing, both to maintain and improve health as synthesized are tested in vitro by testing the solubility in
well as for the treatment of a disease1. Black cumin (Nigella octanol-water that describes the distribution of a compound
sativa) is one of the natural medicines that was used for between the organic phase and the water phase. Octanol-water
alternative treatment of a disease2. This plant also called Black system has a ratio of hydrophilic and lipophilic nearing
cumin, a plant that has long been used as seasoning, including biological systems in the membrane15.
in Indonesia and in the countries of the Middle East region3,4. The process of molecular docking aims to determine the
Black cumin seeds contain 0.4-0.45% w/w of essential oil, interactions of the TQ and TQ derived compounds (C4, C7,
more than 30% oil to 85% total saturated fatty acids a few and C10) as ligands that occur between ligands with specific
macromolecules in the human body. Molecular docking uses The result compounds was tested using thin layer
score functional to predict binding energetic from complex chromatography (TLC), and analyzed its structure by IR
ligand-receptor prediction. The end result of the process of spectrophotometer Shimadzu FT-IR 8400S, Varian 400 NMR
molecular docking is observed ligand value of free energy spectrometers, Shimadzu HPLC and LCMS Hitachi L 6200.
Gibbs (ΔG˚) showing the interaction between the
macromolecule and ligand, the value also can explain in an Molecular docking
inhibition constants (Ki). The greater value Ki then refusal Ligand preparation: 2D ligand structure created on
activity also increases16. Chemsketch and saved in format .hin by OpenBabel 2.3.2
According with potency of thymoquinone as anti-cancer, in software but the geometry optimized before with Hyperchem.
this research we predict activity of derived thymoquinone as That optimization result saved in format .pdb that will be able
ligand with Cytochromes P450 3A4 (CYP3A4) as molecule read with Autodock Vina 4.
target as anticancer. CYP3A4 is a member of cytochrome Macromolecule preparation: macromolecule that will be
P450 family of oxidizing enzymes. This enzyme is involved in used as receptor downloaded from Protein Data Bank
the metabolism of half drugs that are used today, including (www.pdb.org) in 3D structure and saved in format .pdb. The
acetaminophen, codeine, and diazepam. The enzyme also macromolecule was varied to monomer macromolecule and
metabolizes some steroids and carcinogens. Most drugs was allayed a ligand that bonded in macromolecule from side
undergo deactivation by CYP3A4, either directly or by active. In addition, water content was allayed from
facilitated excretion from body. CYP3A4 promotes growth of macromolecule too and save in format .pdb.
various types of human cancer cell lines in culture17. Docking Analysis: The ligand (TQ, C4, C7, and C10) was
docked to the active site of the target (CYP) using Auto Dock
II. EXPERIMENTAL program, version 4.0. Polar hydrogen bonds (H-bonds) were
added to the receptor. The internal degree of freedom and
A. Materials
torsions were defined using the “Ligand torsions” menu option
The materials used in this study is 2,6-dimethyl-1,4- of autodock. The grid maps representing the protein were
benzoquinone Sigma Aldrich pro analysis, Na2SO4 anhydrous calculated using “autogrid” option. The best ligand-receptor
Merck pro analysis, H2O, diethyl ether, chloroform, n-hexane, structure from the docked structures was chosen based on the
AgNO3, (NH4)2S2O8 Sigma Aldrich pro analysis, Sigma lowest energy. The results were visualized using visualization
Aldrich bromopentanoic acid pro analysis, Sigma Aldrich tool Discovery Studio Visualizer.
bromooctanoic acid pro analysis, Sigma Aldrich
bromoundecanoic acid pro analysis, acetonitrile, buffer
Procedures of octanol-water solubility test
phosphate pH 7.4, and n-octanol.
Preparation Buffer Phosphate pH 7.4
Prepared solution of NaH2PO4 1.38 g (0.01 mol) and a
B. Software and Hardware solution of Na2HPO4 2.68 g (0.01 mol). Solution of NaH2PO4
The molecular docking tools used in this study were: taken 39 mL and mixed with 61 mL. Mixed solution is
Autodock Vina 4, PyMOl, Discovery Studio Visualizer 3.5 , adjusted to achieve a pH of 7.4.
OpenBabel 2.3.2 ACD/ChemSketch (freeware version 10.00)
installed on a desktop equipped with AMD A8-7410 APU (4 Aqueous phase saturation (Phosphate Buffer 7.4)
CPUs, 2.2 GHz, 4 GB RAM) running the Windows 10 pro with n-octanol and n-octanol phase saturation with water.
operating system.
Buffer phosphate solution pH 7.4 was prepared and
saturated with n-octanol. Likewise, a solution of n-octanol
C. Procedures saturated with pH 7.4 buffer solutions were prepared. Octanol
Synthesis Bromoalkylquinone solubility in water at room temperature is very low but the
The basic ingredients 2,6-dimethyl-1,4-benzoquinone 0.272 water solubility in octanol quite high18, so that the second
g (2 mmol) was treated with 5-bromopentanoic acid 0.362 g phase should be saturated before partitioned.
(C4) or 8-bromooctanoic acid 0.446 g (C7) or 11- Phosphate buffer solution 20 mL was taken and put into a
bromoundecanoic acid 0.530 g (C10) (2 mmol), silver (I) separating funnel. The solution was added dropwise n-octanol
nitrate 0.169 (1 mmol) was dissolved in 7 mL acetonitrile and to saturation, where the water phase and n-octanol separated.
water mixture (2:1), mixed in 80 °C temperature while N-octanol phase discarded. In the n-octanol phase saturation
stirring. Ammonium persulfate solution of 0.456 g (2 mmol) with water, a solution of n-octanol taken 20 mL and put into a
in 3 mL of water was added dropwise to the mixture with separating funnel. The solution is added dropwise to a
stirring and heated at a temperature of 70-89 °C for 1.5 hours. saturated solution of phosphate buffer, wherein the aqueous
The mixture was extracted with diethyl ether. Diethyl ether phase and n-octanol separated, the aqueous phase discarded.
layer was taken, washed with water, and dried with sodium The second phase has been saturated put into separating
sulfate. The solvent was evaporated with a rotary vacuum funnel, stirred and allowed to stand for 24 hours to ensure both
evaporator. The residue was separated using column of octanol and water phase are completely separate.
chromatography with chloroform : n-hexane (3:7) as eluent.
(NH4)2S2O8 was added dropwise. The reaction was continued
Determination of Partition Coefficient at a temperature of 70-89 °C (120 minutes for C4, 90 minutes
Based on the nature properties of thymoquinone, low for C7 and C10). At this stage lasts alkylation process,
nucleophile species entered the aromatic ring by way of a
solubility in water and extremely high lipophilicity, it will be
proposed procedures for hydrophobic compounds. nucleophilic aromatic substitution.
Thymoquinone compound and its compounds are dissolved in Crude product was extracted with diethyl ether. Diethyl
n-octanol saturated with buffer solution, and then partition ether layer was taken and dried with Na2SO4 anhydrous. The
octanol/water different conducted in accordance with the solvent was evaporated with a rotary vacuum evaporator then
estimated value log P7.4 medications. Standard solution analyzed TLC. TLC showed that the product generates two
prepared by diluting the solution with water saturated n- spots with different Rf. The mixture of compounds separated
octanol. Comparison of the volume of octanol and water used using column chromatography with the eluent n-hexane:
in Table 1. chloroform (7: 3). Results of the column in the form of
fractions unknown when tested TLC. The fraction that has a
TABLE 1 COMPOSITION OF PARTITION COEFFICIENT TEST stain with same Rf collected in same place and then the
solvent evaporated. Compounds were characterized using
Mass of FTIR spectrophotometer and spectrometer 1H-NMR and 13C-
Va Vo
Mass Product (mg) Thymoquinone NMR and LCMS. Compounds tested solubility in octanol-
(mL) (mL) water using HPLC.
(mg)
C12H15 C15H21 C18H27 Product synthesis was produced in each compounds both of
O2Br O2Br O2Br physically and chemically. Based on the test results of TLC,
7 3 8.127 9.387 10.647 4,926 product of C4 still contains the starting material (DBQ) that
have not reacted. It is shown the come up of two stains that
one stain with Rf value of 0.4 is the same as the DBQ. Stain
Partitions shaken for one hour at room temperature with a that the product has Rf greater than Rf DBQ. Product of C4
speed of 200 rpm. Both standard octanol phase and water has lower polarity than DBQ. Meanwhile, product of C7 and
phase, after the equilibrium of each partition, then measuring C10 have been formed. There are shown from the stains that
the concentration using HPLC for analysis. have different Rf with Rf DBQ. Based on Rf value, C7 and
C10 have lower polarity than DBQ. The nature of polarity is
decreased due to the addition of alkyl chains as substituents on
III. RESULTS AND DISCUSSION
the structure of DBQ. Alkylation products was extended in
wavelength by Bathochromic shift with alkyl inserts resulting
1. Synthesis and Characterization from excessive conjugation with alkyl groups easily move to
interact with chromophore groups. Spectra comparison
The method used in this synthesis was reflux. The starting between DBQ and products shown in fig. 2. Characterization
material, 2,6-dimethyl-1,4-benzoquinone, underwent
by TLC and spectrophotometer UV-Visible shown in Table 2.
alkylation reaction by reacting with the acid 5-bromopentanoat
(C4) or 8-bromooktanoic acid (C7) or 11-bromoundecanoic
acid (C10), AgNO3 which has been dissolved in a mixture of
acetonitrile and water (2:1). This should be put in methods
alkylation reaction of 2,6-dimethyl-1,4-benzoquinone showed
in Fig 1.
n = 4, 7, and 10
Fig. 1. Bromoalkilation Reaction of 2,6-dimethyl-1,4- Fig. 2. Comparison of spectral UV-Visible DBQ and
benzokuinon (DBQ) alkylation products
IV. CONCLUSIONS
From this research derivative compound of thymoquinone
was successfully synthesized. Based on the characterization
using UV-Vis spectrophotometer, alkylation products
undewent a bathochromic shift. FTIR spectra from alkylation
product has a C-Br bond. The spectra of 1H-NMR and 13C-
NMR products have environmental matched with the structure
that we predict. Spectrum of LCMS showed that the m/z
values indicate suitability molecular weight product.
Molecular docking depicted descent of QSAR value (Ki, ∆G˚,
IC50) on CYP3A4 as anticancer receptor. Solubility test
compound alkylation product C4, C7 and C10 in octanol-
water showed that the bromoalkylation product is more
soluble in octanol phase than the water phase. C7 showed that
the value of the partition coefficient greater than
thymoquinone that only 2.58. C7 product allows as effective
as the drug compound is better than thymoquinone. Overall,
derivatives of thymoquinone (C4, C7, C10) could be
considered as effective base materials for anticancer drugs. In
Fig. 5. Chromatogram of C4, C7, and C10 in octanol (orange) and the future, their activities in cell culture will be investigated,
phosphate (blue) and their mechanism of actions will be explored as well.
Abstract— Welfare is a common goal of every country in the survey conducted by Gallup World Poll from 2015-2017 about
world. Likewise, Asian Countries, which are the largest continent happiness globally.[6] And measured by various indicators.
in the world and become a benchmark for the welfare of the According to the Substainable Development Goals
world community. The welfare of the world community is created (SDG's) document attended by representatives of the world
one of them as the ladder of happiness of people in a country. We community. The main goal of the entire world community is
will provide happiness mean with six variables, these are GDP,
social support, healthy life expectancy, freedom to make life
to achieve equitable prosperity. The problem that occurs is
choices, generosity, and perception of corruption. With that many countries only focus on their countries. Countries
classifying Asian Countries using K-means clustering analysis, that have the highest level of happiness continue to increase
which is a non-hierarchical cluster that aims to classify objects while countries with low levels of happiness continue to
based on analysis by variable averages at 40 countries in Asian decline so that there is a large distance to these conditions.
based on the World Happiness Report 2018. The result is shown Therefore, as an Asian community, which is a society with
that there are three groups of happiness (clusters). Not happy, the largest region in the world, it should be the pioneer of the
quite happy, and happy. The first cluster describes countries with
formation of collaboration and mutual understanding between
average happiness below the average general happiness that is
not happy with the number of 10 countries. The second cluster countries. The first step that must be made is by mapping and
describes countries with average happiness among the average clustering countries according to the same conditions of
public happiness that is quite happy with the number of 17 happiness, it needs to be done so that fellow countries in Asia
countries. The third cluster describes countries with average understand the conditions of each country. And can
happiness above the average general happiness that is happy with collaborate to overcome the welfare inequality of happiness
the number of 13 countries. Asian countries can be aware about
from certain countries that are low.
these clusters and build synergy to increase the ladder of
happiness in Asia to realize the welfare of the world community.
II. THEORY
Index Terms— Happiness, K-means Clustering, Welfare, Bagian ini berisi tentang teori atau pustaka yang
World Happiness Report mendukung riset/penelitian.
I. INTRODUCTION A. Happiness
At present, the measurement of welfare is very important to Happiness is actually a result of self-assessment and life. While
see about the quality and health of human beings in a country. according to Carr (2004), Happiness is a reflection of various life
There are many welfare measures, such as economic growth, satisfaction on the condition of personal, social, and the resulting
gross domestic products, and per capital income. The impact of the environment. [2]
calculation is based on capital resources, production and
wealth of a country. B. K-means Clustering
Al along with its development, this concept cannot reflect the Cluster analysis is used to classify objects or cases into
condition of society in a country widely because the measurement relatively homogeneous groups called clusters, objects or cases
only looks at the material, such as labor factor and economy, in each group tend to be similar to each other and far different
which is based on material. The concept of GDP is considered to (not the same) from objects from other clusters. [3]
fail to answer and describe the quality of human life as
The process of forming clusters is divided into two, namely
individuals in development, prosperity and relations with
hierarchy and non hierarchy. The formation of hierarchical
society so that the concept of national welfare does not always
measure everything financially, one of which is the concept of clusters has branching tree-like properties. While the non-
the Happiness Index issued by the Wolrd Hapiness Report, a hierarchical seing method is called the K-mea method. The
cluster formation process is divided into two, namely
2
hierarchy and non hierarchy. The formation of hierarchical KMO Measure 0.625
clusters has branching tree-like properties. While the non-
hierarchical seing method is called the K-means method.[1]
The KMO value is greater than 0.5 so the data represents
There are three steps to simple K-means method:
the existing population. Meanwhile, to see the multicollinity
1. Partitioning objects into the initial cluster K
of VIF values in the data there is no multicollinality. Because
2. Starting with recording objects, assigning objects to a
the VIF value is below 10, there is no multicollinality.
cluster that have the nearest centroid (mean).
3. Step 2 is repeated until there are no more object The number of K clusters is determined by the researcher.
transfers.. In this case. Researchers set 3 clusters, namely Not Happy,
Quite Happy, Happy.
C. Welfare By using SPSS 23.0 sortware it was found that
Bentham (1769) believes that something that can cause TABLE 2
extra happiness is a good thing. Conversely, something that CLUSTER GROUP
causes pain is bad. So that it can be concluded that Welfare is Number of Cases in each
a condition of fulfilling individual material and non-material
needs.[5] Cluster
Cluster 1 10,000
VI. REFERENCE
Irwansyah1,2
1)
Mechanical Engineering Department, Syiah Kuala University, Aceh, 23111, Indonesia
2)
Mechanical Engineering Department, National Central University, Taoyuan City 320, Taiwan
*irwansyah@unsyiah.ac.id
Abstract- Rekayasa virtual pada rekonstruksi model tiga- virtual menyerupai kondisi nyata, membantu tenaga medik
dimensi (3D-model) hingga pesatnya perkembangan teknologi dalam menganalisa secara visual dan melakukan simulasi
manufaktur cetak objek fisik (3D-printing) telah menyita penanganan operasi.
perhatian berbagai kalangan dibidang teknik dan medik. Teknologi rekonstruksi model digital 3D saat ini masih
Penerapan kedua teknologi tersebut dapat menjadi solusi dalam
mengacu pada prinsip komputer desain yang berbasis
mengatasi keterbatasan menginterpretasi gambar citra medik
2D yang dihasilkan instrumen computer tomography (CT) dan polygon-based dibandingkan computer-aided design (CAD)-
magnetic resonance imaging (MRI). Akan tetapi, umumnya 3D based, dimana permukaan dari objek dirangkai dari ribuan
model hasil rekayasa memberikan dampak meningkatnya ragam segitiga-segitiga (triangular mesh). Hal ini berdampak
kapasitas penyimpanan data yang mengakibatkan menurunnya pada peningkatan jumlah data yang dimiliki dan
kecepatan tampilan grafis dan meningkatkan waktu operasi mengakibatkan meningkatnya ruang penyimpanan data,
komputer. Pengembangan algoritma berbasis teknik reverse menurunnya kecepatan komputer untuk menampilkan bentuk
engineering (RE) telah dilakukan pada penelitian ini untuk grafis dan meningkatnya waktu operasi pengolahan model
mengoptimalkan proses rekonstruksi model tiga dimensi 3D. Disamping itu, beberapa detil informasi yang berguna
berbasis computer-aided design (CAD). Teknologi cetak tiga
dari kondisi aktual objek yang dipindai juga dapat hilang [4].
dimensi atau rapid prototyping (RP) digunakan untuk
mempabrikasi objek fisik dari hasil rekonstruksi virtual model Sehingga membangun model 3D dari data gambar pencitraan
dalam skala penuh 1:1. Kasus biomedik tentang fraktur CT berdasarkan prinsip CAD-based menjadi pilihan yang
ortopedi di demonstrasikan untuk menunjukkan fisibilitas dari patut dipertimbangkan dan dikaji lebih lanjut.
teknik rekayasa model virtual dan hasil fabrikasi menggunakan Tahapan rekonstruksi model 3D, diawali dengan akusisi dan
teknologi printer tiga dimensi. filterisasi data rekam medis dari hasil penginderaan instrument
CT atau MRI. Disebabkan oleh kompleksitas struktur dan
Index Terms- computed tomography, fraktur, model virtual, jaringan anatomi, data rekam medis CT disegmentasi
CAD, 3D printing. berdasarkan struktur tulang, jaringan tissue dan sejumlah data
yang tidak diinginkan (noise). Untuk mengatasi hal tersebut,
teknik pengolahan gambar (image processing) yang tepat
I. PENDAHULUAN diperlukan pada proses segmentasi dan deteksi batasan struktur
Pemanfaatan teknologi rekonstruksi digital dari model anatomi tulang. Akurasi data dipengaruhi oleh resolusi data gambar,
3D (virtual model) dan cetak 3D objek (3D printing) sudah kualitas gambar, dan penyimpangan titik acuan dari setiap
menjadi kebutuhan yang tidak dapat dihindari untuk mendukung lembaran gambar [5]. Selanjutnya, teknologi surface rendering
keberhasilan, termasuk pada bidang kedokteran. Data hasil atau volume rendering dilibatkan untuk menyajikan model 3D
pemindaian baik menggunakan instrumen computer tomography dari gambar citra medik secara keseluruhan dengan
(CT) maupun magnetic resonance imaging (MRI), merupakan mengikutsertakan informasi bagian internal dari model [6]. Pada
media utama yang digunakan untuk menelaah dan mendiagnosa pendekatan rekonstruksi bangun iso-surface, permukaan segitiga
kasus medik pada struktur atau jaringan internal tubuh. Data ini mesh ditampilkan dengan menerapkan algoritma Marching cubes
kerap disajikan dalam bentuk tampilan gambar dua-dimensi (MC). Bangun model dibentuk dengan merangkai kubus-kubus
(2D), yang memuat penampang dari area yang dipindai [1, 2]. kecil imajiner dalam pola tertentu mengikuti kontur permukaan
Pada bidang ortopedi, tenaga medik menggunakan sekumpulan objek [7]. Tahapan akhir, data informasi yang memuat hasil
gambar citra irisan anatomi secara bersamaan untuk mendukung mesh dari bangun model disimpan dalam format 3D. Standar
keberhasilan den ketepatan dalam menetapkan rencana pra- format penyimpanan data 3D yang kerap digunakan untuk
operasi. Hal ini merupakan tugas yang sulit untuk dilakukan keperluan industri atau manufaktur adalah Stereolithography
secara manual, mengacu pada kompleksitas geometri dan atau Standard Tessellation Language (STL).
struktur anatomi serta sulitnya menginterpretasi gambar citra 2D Perwujudan fisik dari model digital yang dihasilkan dari
[3]. Pemutakhiran data hasil pencitraan medis CT yang rekayasa komputer dibutuhkan untuk memperkuat diagnosa
dikonversi kedalam bentuk model dan menjadi bagian kelengkapan dalam kominikasi antara
tenaga medis dan pasien [8]. Teknologi cetak tiga dimensi dibedakan dua jaringan organ, jaringan cortical dan trabecular.
(3D printing) telah berkembang luas penggunaan di bidang Jaringan cortical diketahui merupakan padatan dan berada pada
ortopedi [9,10]. Teknologi ini mengkombinasikan teknik permukaan luar tulang, sedangkan jaringan trabecular berada
desain berbasis computer-aided design (CAD) dan teknik pada bagian inti tulang. Kedua jenis jaringan ini memiliki
computer-aided manufacturing (CAM) untuk menghasilkan intensitas berbeda. Tetapi pada beberapa daerah di tulang
objek fisik anatomi yang berstruktur komplek. Diantara memiliki kemungkinan intensitasnya sama dengan intensitas
beberapa teknologi cetak 3D yang populer, fused-deposition jaringan yang ada disekelilingnya. Kejadian ini akan
modeling (FDM) merupakan teknologi yang banyak mengakibatkan tidak sempurnanya segmentasi. Gambar citra dari
digunakan untuk keperluan biomedik. Teknologi FDM instrumen CT merupakan sumber informasi yang sangat baik
mampu menghasilkan objek fisik dengan sifat mekanik yang untuk digunakan dalam memisahkan antara fraktur tulang dan
baik, mudah dalam pengoperasian dan berbiaya produksi jaringan organ lainnya. Secara literatur, terdapat beberapa kajian
rendah [11,12,13]. yang telah dilakukan untuk mensegmentasi jaringan fraktur
Kajian dalam tulisan ini memaparkan penggunaan teknologi tulang yang bersumber dari instrumen CT. Empat kategori dari
reverse engineering dalam rekonstruksi model 3D berbasis CAD sistem segmentasi yang lazim digunakan adalah berbasis
dari gambar citra medik dan teknologi rapid prototyping dalam intensitas (intensity-based), berbasis batas area (edge-based),
mencetak objek fisik. Detail tahapan proses visualisasi dan berbasis region (region-based) dan berbasis registrasi
rekonstruksi model 3D diurai dan didiskusikan serta dilanjutkan (registration-based). Diantara sistem segmentasi tersebut,
dengan pembahasan fabrikasi cetak objek fisik 3D. segmentasi berbasis region digunakan untuk mengidentifikasi
jaringan tulang dari gambar CT [16].
II. DASAR TEORI
(3) Rekonstruksi model permukaan (surface model):
A. Rekonstruksi Virtual Mode 3D Data citra medik CT merupakan serangkaian gambar 2D yang
Rekonstuksi virtual mengacu pada pengertian suatu proses dapat dinyatakan sebagai sekumpulan data volume dalam
rekayasa atau membangun sebuah model digital dengan formasi matrik 3D mengacu pada nilai elemen pixel pada tiap
bantuan teknologi komputer. Proses rekonstruksi ini mengacu irisan gambar. Metode yang digunakan untuk membangun model
pada teknologi reverse engineering (RE), yaitu menggali data berpermukaan segitiga (triangular model) adalah dengan
akusisi dari instrumen pemindai dan menampilkannya dalam mengekstrak kontur gambar 2D dari setiap irisan yang dipindai
wujud model digital 3D. Untuk mendukung keberhasilan (contour-based) dan membangun susunan 3D elemen volume
membangun model 3D dari data gambar citra medik, atau voxel dari irisan gambar citra. Teknik volume rendering
beberapa tahapan proses yang dilakukan adalah: dapat juga digunakan untuk menampilkan gambar permukaan
(1) Data akuisisi dan pra-proses: model dari informasi data volume tersebut [17]. Rekonstruksi
Gambar citra medik atau data akuisisi yang memuat informasi model secara langsung dari gambar CT merupakan proses yang
lengkap anatomi tubuh diperoleh dari instrumen pencitraan. Dua komplek dan menghendaki waktu operasi yang lama bagi
sistem pencitraan gambar medik yang sering digunakan adalah komputer. Untuk mengatasi hal ini, permukaan model diurai
Computerized tomography (CT) dan Magnetic Resonance dalam bentuk poligon sederhana yang berbentuk segitiga dalam
Imaging (MRI). Adapun sistem lain yang dapat digunakan adalah jumlah tertentu. Poligon sederhana yang berbentuk segitiga ini
sistem ultrasonik, Mammography dan sinar-X [14]. Hal utama dikenal sebagai mesh. Metode popular dan merupakan standar
dari pemilihan sistem ini adalah kemampuan dari sistem untuk yang digunakan untuk membangun model 3D (isosurface) dari
dapat menyediakan informasi akurat mengenai struktur anatomi himpunan data 2D adalah Marching Cubes (MC). Prinsip kerja
dan ketidaknormalan yang ditemukan pada tubuh. Perbandingan dari metode ini adalah merekonstruksi model 3D mengacu pada
kemampuan sistem pencitraan, CT dan MRI menghasilkan konstanta densitas permukaan dari titik-titik sekumpulan gambar
gambar medik dengan resolusi yang sangat baik. Pada proses citra 2D. Sederhananya, metode ini menggunakan kubus yang
pemindaian, pasien di pindai dalam rentang bidang pengukuran dibangun dari delapan titik-titik (pixels) yang berada di dua
2-3 mm persatuan waktu. Informasi yang diperoleh dari setiap lapisan pindai yang bersinggungan. Selanjutnya, kubus- kubus
irisan pemindaian dirangkum untuk membangun struktur kecil imajiner yang terpola tersebut dijadikan acuan untuk
anatomi. Model hasil pemindaian yang direkonstruksi dapat membangun model 3D. Perangkat lunak yang tersedia secara
merepresentasikan struktur anatomi menyerupai kondisi yang open-source atau komersial untuk melakukan segmentasi dan
sesungguhnya [15]. rekonstruksi model 3D struktur anatomi dari data citra medik
diantaranya adalah OsiriX (Pixmeo SARL), Mimics (Materialise
(2) Segmentasi 3D: NV), and Amira (Thermo Fisher).).
Segmentasi merupakan tahapan yang dilakukan untuk
menentukan dan memisahkan titik-titik pixel bagian anatomi
yang menjadi target dan jaringan organ disekitarnya. Pada B. Cetak objek fisik 3D
kasus tulang yang mengalami fraktur atau tidak, segmentasi Teknologi cetak 3D atau dikenal juga dengan teknologi
dari gambar CT merupakan pekerjaan yang sulit dikarenakan manufaktur lanjut (rapid prototyping) kerap digunakan untuk
kompleksitas bentuk yang acak dan singgungan dengan mendukung keperluan biomedik [18]. Prinsip dasar teknologi
jaringan organ terdekat. Umumnya, pada tulang dapat ini adalah mencetak objek 3D secara bertahap lapis per lapis
(layer by layer), dimana nosel bergerak dari lapisan bawah
objek hingga selesai mengikuti penampang irisan dari gambar dikonversi menjadi sekumpulan data volume dalam formasi
CAD yang dikendalikan dengan sistem berbasis komputer matrik 3D yang mengacu pada nilai elemen pixel (gray value)
numerik (Computer Numerical Control, CNC). Terdapat pada tiap irisan gambar. Teknik volume rendering digunakan
beberapa metoda teknologi cetak 3D yang dapat digunakan untuk menampilkan gambar isosurface dari data volume.
mengacu pada pilihan jenis material, kecepatan manufaktur, Tahapan segmentasi, proses identifikasi dan pemisahan
akurasi dan biaya produksi. Diantara teknologi cetak 3D yang struktur anatomi ini dapat dilakukan secara otomatis atau
berbasis pada jenis material adalah padatan (filamen solid- manual. Idealnya, metode proses segmentasi dilakukan secara
based), cairan (liquid-based) dan serbuk (powder-based). simultan untuk multi bagian struktur anatomi, guna mengurangi
Mengacu pada biaya material, teknologi mesin cetak 3D yang waktu proses yang terlalu lama bila dilakukan secara bagian per
berbasis filament padatan (Fused Deposition Modeling, FDM) bagian. Tetapi, metode ini tidak mudah untuk diterapkan pada
berbiaya rendah dibandingkan lainnya. Hal ini menjadi keseluruhan kasus fraktur medik. Untuk kasus yang tidak
pertimbangan untuk cetak objek dalam jumlah besar, tetapi dilakukan secara otomatis, dapat dilakukan secara manual,
teknologi ini kurang unggul dalam hal sifat mekanis material dan melalui tahapan kombinasi region dan re-segmentasi region.
kekasaran permukaan dari objek hasil cetak. Teknologi FDM Pada segmentasi multi-region, sebuah algoritma dilibatkan untuk
sangat popular dan terdepan dalam proses dan pengoperasian. menetukan titik umpan (seed point) secara otomatis, dilanjutkan
Teknologi berbasis cairan (Stereolithography, SLA) dan berbasis dengan penerapan algoritma pembiakan region (region growing)
serbuk (Selective Laser Sintering, SLS) mampu menghasilkan untuk menjalarkannya ke semua region secara bersamaan.
kualitas cetak objek yang lebih baik, namun keduanya berbiaya Pendekatan ini berhasil mensegmentasi semua region dengan
produksi tinggi. baik, hanya sebagian kecil yang memerlukan perbaikan. Proses
rekombinasi region dan re-segmentasi digunakan untuk
mengatasi region yang belum tersegmentasi sempurna.
III. METODE
Algoritma rekombinasi region akan memperbaiki kesalahan
:Pada kajian ini, proses rekonstruksi model 3D dibai dalam segmentasi, sedangkan algoritma re-segmentasi berfungsi untuk
dua tahapan utama yaitu reverse engineering (data akuisisi memisahkan bagian yang tersegmentasi tidak sempurna [19].
iso surface, segmentasi 3D, model STL) dan rapid
prototyping (setak objek 3D. Uraian lengkap ditampilkan Pada kajian ini untuk membangun model triangular suatu
pada diagram kerja berikut ini: struktur anatomi, dua prosedur yang diterapkan yaitu pengolahan
gambar citra (image processing) dan pembentukan dan
Perbaikan (triangular mesh). Kedua prosedur dikaji secara
bersamaan, karena hasil pengolahan gambar berpengaruh
terhadap triangulasi model. Selanjutnya algoritma marching
cubes digunakan untuk membentuk model triangular, diikuti
dengan proses interpolasi linear agar menghasilkan permukaan
yang halus. Untuk menghasilkan model 3D yang siap di
fabrikasi dan sesuai dengan persyaratan proses cetak 3D,
dilakukan pemeriksaan cacat (mesh error) dan ketidak akurasian
geometri pada model 3D. Kesalahan atau cacat mesh yang terjadi
mengakibatkan terbentuknya rongga, lubang, persilangan atau
saling berhimpitan antar mesh, menghasilkan
ketidaksempurnaan hasil akhir produk cetak 3D. Selanjutnya
data model 3D yang telah diperbaiki, disimpan dalam format
STL untuk dikirim ke mesin cetak 3D.
Peralatan yang digunakan untuk mendukung pemodelan dan
simulasi rekonstruksi model 3D pada kajian ini adalah sebuah
personal komputer (Intel® Core™ i5-4440 CPU, 3.1 GHz
processor, 4 GB RAM, Windows 7 operating system) dan satu
paket program komputer simulasi perencaanan pra-operasi bedah
ortopedi (PhysiGuide v2.72.) yang dikembangkan oleh
laboratorium Bio-Images and Assistive Device, Dept.
Mechanical Engineering, National Central University, Taiwan.
Untuk menguji performa dari prosedur rekonstruksi model 3D
Gbr. 1. Tahapan utama proses rekonstruksi virtual model 3D yang diajukan, sebuah gambar citra medik (Siemens CT, X-ray
tube current 67 mA, KVP 110 kV, resolusi setiap irisan
Pada tahapan data akusisi, sekumpulan data yang di ekstrak 512×512,ukuran spasi pixel 0.3 mm, dan tebal irisan 1
dari instrument CT, disimpan dalam bentuk digital imaging and mm) dari kasus struktur tulang ankle digunakan, calcaneus
communication in medicine (DICOM). Selanjutnya fraktur dengan klasifikasi tipe 2A. Pabrikasi objek fisik untuk
model 3D calcaneus menggunakan teknologi berbasis FDM.
Mesin cetak tiga dimensi berbiaya produksi rendah, Aurora F1
digunakan, material filamen Polylactic Acid (PLA), dan tersegmentasi sempurna. Sehingga, koreksi dilakukan dengan
akurasi produk akhir cetak 3D adalah 0.1 0.4 mm. re-kombinasi atau re-segmentasi region fraktur tersebut.
Waktu operasi yang dibutuhkan komputer untuk membangun
isosurface hingga segmentasi kasus calcaneus ini adalah 122
IV. HASIL PENELITIAN detik. Untuk melakukan proses reposisi (fracture reduction)
Hasil rekayasa menggunakan perangkat lunak simulaisi pra- kelima region segmentasi fraktur tersebut menghabiskan waktu
operasi bedah berbantuan komputer telah memperlihatkan operasi 162 detik. Sehingga waktu operasi komputer keseluruhan
unjukkerja yang baik dalam mewujudkan model 3D secara detail yang dibutuhkan adalah 284 detik. Region fraktur yang
mendekati keadaan aktual, sebagaimana terlihat pada gambar 2. tersegmentasi merupakan bagian dari satu kesatuan dari model
Tampilan pandangan isometrik model 3D yang menyuguhkan dalam format isosurface, untuk melakukan reposisi maka setiap
keseluruhan struktur anatomi dan dibangun menggunakan regin tersebut di proses menjadi model triangulasi. Hal ini
metode volume rendering diperlihatkan pada bagian kiri atas dilakukan untuk memudahkan tahapan reposisi setiap bagian
gambar 2 (a). Model isosurface tersebut telah melewati tahapan fraktur tersebut, untuk dirubah orientasinya baik secara translasi
filterisasi terhadap noise yang timbul pada saat ekstraksi gambar maupun rotasi. Pada gambar 3 memperlihatkan hasil model tiga
citra dan membangun model 3D. Hasil proses segmentasi 3D, dimensi yang telah dilakukan proses triangulasi mesh dan
dimana nilai threshold yang ditetapkan adalah T=600 telah dapat dipadankan dengan model pelat fiksasi. Pada tahapan
menampilkan dengan jelas region fraktur yang berukuran besar pembentukan mesh, pengurangan jumlah mesh dan penghalusan
secara terpisah. Namun, masih ditemukan sebagian kecil region permukaan kontur geometri model 3D perlu diperhatikan.
yang belum tersegmentasi sempurna. Pada kajian ini, bagian Semakin banyak jumlah mesh akan menghasilkan model 3D
fraktur yang berukuran besar menjadi pertimbangan, mengacu dengan detail kontur geometri yang tinggi, akan tetapi hal ini
pada penanganan medik lanjut yang dilakukan untuk dikuti dengan meningkatnya kapasitas penyimpanan data dan
memposisikan dan memfiksasi fraktur tersebut sesuai dengan waktu operasi computer. Sebaliknya dengan model dengan
keadaan anatomi semula. Bagian fraktur calcaneus yang jumlah mesh yang terlalu sedikit, mengakibatkan model 3D
tersegmentasi menjadi lima region dapat ditandai pada tampilan terdeformasi bentuknya jauh menyimpang dari aktual dan
jendela graphical user interface (GUI) berdasarkan perbedaan berpermukaan kontur geometri kasar. Pada kajian ini algoritma
warna yang muncul pada setiap region. Terdapat tiga tampilan MC yang telah dimodifikasi dipadu dengan melibatkan
pandangan bantu yang menampilkan penampang irisan dari interpolasi linear untuk memperoleh model 3D yang sesuai
gambar CT, pandangan transversal (Gbr. 2(b)), pandangan untuk keperluan medik. Pada kasus medik yang tidak
sagittal (Gbr. 2(d)) dan pandangan coronal (Gbr. 2(c)). Ketiga menghendaki detail pada produk akhir dan hanya digunakan
pandangan dapat digunakan untuk melakukan analisa faktur sebagai media untuk berkomunikasi dengan pasien dapat
yang tidak menggunakan model 3D
(a) (b)
(c) (d)
Gbr. 2. Rekonstruksi model 3D ankle kaki. (a) model 3D jaringan dan struktur anatomi, (b) segmentasi 3D tampak pada pandangan transversal, (c)
pandangan hasil segmentasi pada bidang sagittal, dan (d) pandangan hasil segmentasi pada bidang coronal.
dengan jumlah mesh yang tidak terlalu besar. Pada gambar dirakit kembali, seperti permainan menyusun balok (puzzle
3(a) model calcaneus di bangun dengan jumlah mesh polygon cubes). Bagian fraktur dirakit sesuai dengan hasil manipulasi
24999, vertices 12201, panjang calcaneus 79.33 mm. lebar virtual umtuk mereposisi fraktur yang dilakukan pada
52.88 mm dan tinggi 48.14 mm. Hasil model 3D yang telah tahapan sebelumnya mengacu pada posisi anatomi (Gbr.
melewati koreksi mesh dan kehalusan permukaan kontur 4(a)). Hasil cetak 3D pelat fiksasi dan sekrup yang
geometri ditunjukkan pada gambar 3(b). dibubuhkan dapat dijadikan media evaluasi mengenai
penanganan fraktur (Gbr. 4(b)). Membutuhkan waktu satu
(a) (b) hari untuk menyelesaikan model 3D ini, dari ekstraksi
gambar citra CT hingga fabrikasi objek fisik 3D.
V. KESIMPULAN
I. INTRODUCTION
II. BASIC THEORY
Combustion is a process of producing heat in the
a. Furnace
thermal industry. Combustion occurs when the required
A fuel-fired furnace may be visualized as a gaseous
condition are met as known as the fire triangle, such as
heat source (the flame and furnace gases), a sink, and a
oxygen, heat and fuel. The Republic of Indonesia's Ministry
refractory enclosure. Heat is transferred to the sink surface
of Energy and Mineral Resources states that Indonesia only
by radiation and convection from the furnace gases and
has proven reserves, namely petroleum around 3.2 to 3.3
radiation from refractory surfaces. [Rhine, Tucker, and
billion barrels or 0.2% and gas around 1.5% of total world
Truelove, ]
reserves. Therefore, it is necessary to conserve fuel,
b. Combustion
especially in industries that require relatively large amounts
of heat. One of them is by using a cogeneration system on Combustion occurs when fossil fuels, such as
the gas stack to utilize the sensible flue gas heat as a hot natural gas, fuel oil, coal or gasoline, react with oxygen in
fluid on a heat exchanger. the air to produce heat. The heat from burning fossil fuels is
used for industrial processes, environ-mental heating or to
Analysis of combustion chamber performance is
expand gases in a cylinder and push a piston. Boilers,
usually done by direct or indirect methods. Direct method
furnaces and engines are important users of fossil fuels.
is a method of calculating the performance of a combustion
[TSI Incorporated, 2004]
chamber based on heat that is able to be absorbed by the
feed during the heating process. Whereas indirect method is
a method of calculating furnace performance based on
energy losses in the combustion process. Based on the
analysis of furnace performance that has been done
previously using box-type furnace for heating the feeds in
Cogeneration systems are of several types and almost all
types primarily generate electricity along with making the
best practical use of the heat, which is an inevitable by-
product. [Devki Energy Consultancy Pvt. Ltd., 2006]
iC5H12 0,1 0%
23-Jul-18 24-Jul-18 25-Jul-18 26-Jul-18 27-Jul-18
nC5H12 0,04 Efisiensi
Optimasi
C6H14 0,01
Figure 4. Effect of Decreasing Flue Gas Temperature on
CO2 5,1 Furnace Efficiency
N2 2,02
Effect of Decreasing Flue Gas
Total 100 Temperature on Fuel Cost Thrift
Source : PT Pertamina RU III, Plaju
Rp3,750,000,000
Rp3,702,119,322
b. Calculation Data Rp3,700,000,000
Rp3.639.808.490
1. Actual Operation of Furnace
Cost /Year
Rp3,650,000,000
Rp3,450,000,000
Comparison of Thermal Efficiency Rp3,400,000,000
Furnace
Rp3,350,000,000
iency
Effic
78% Date
76% 73.481%
74% 71.916% 71.480%
69.628% Fig 5. Effect of Flue Gas Temperature on Cost Savings
Thermal
72%
V. CONCLUSION
1. On the actual data calculation Furnace F14-001 for 5 working
days shows that the performance is still quite good, namely
the highest efficiency of 77.663% with 85% design efficiency.
2. The use of a cogeneration system to streamline flue gas heat
affects the efficiency of furnaces and cost savings
3. The development of a more effective cogeneration tool
business is very potential because it is an important
equipment to improve tool efficiency and reduce production
costs.
4. The heat savings from the biggest flue gas is 7023551,514
Btu with a cost savings of Rp. 3,702,119,322/year
Bibliography
Devki Energy Consultancy Pvt. Ltd., 2006. Cogeneration.
Vadodara: Devki Energy Consultancy Pvt. Ltd.,
Hougen, Olaf A., dkk. 1943.Chemical Process Principles.
Charles E. Tuttle CO., : Tokyo.
Kern, Donald Q. 1950. Process Heat Exchanger. Mc.
Graw-Hill Book Co :New York.
Rhine, J.M. 1977. Heat Transfer iin Furnace. London:
World Energy Conference.
Richardson & Coulson’s. 1983. Chemical Engineering
Design. Elsevier: United Kingdom.
TSI Incorporated. 2004. Combustion Analysis Basics.
United States America: TSI Incorporated
The Impact of Financial Performance of
Biotechnology and Medical-related Companies
Listed on Taiwan Stock Market to Its Value of
Stock Owned by Government of Taiwan
Rifqi Jauhar Kamal
Department of International Management of Business Administration
Faculty of Management National Yunlin University of Science and Technology (Yuntech)
123 University Road, Section 3, Douliu, Yunlin 64002 Taiwan (Republic of China)
Abstract—The biotechnology and medical-related NT$179.1 billion, of which NT$43.4 billion came
companies is on the intersection between the commercial from biotechnology, with 434 companies. The scope
businesses to obtain profit and nonprofit entity to invent of businesses covered included genomics, drugs,
the public health. This research has purpose to measure
diagnostics, agricultural biotechnology,
the Impact of financial performance of Biotechnology
environmental biotechnology, protein drugs, contract
and Medical-related Companies listed on Taiwan Stock
Market to Its value of stock owned by Government of
research organizations, biochips and bioinformatics
Taiwan. This research has 17 samples of company based [4].
on the purposive sampling method that is took from TW In order to obtain the expected future growth,
Incorporated with the period of time 2005-2014 for the Taiwanese Biotechnology and medical-related
financial performance. Method of analysis in this companies keep going to public market stock to offer
research is multi-linear regression with the classical the share and expected to grab $ 400 Million USD in
assumption test. The result of the F test shows that the 25 years from public investment [12]. Even if the
dependence variables (P/E,ROA and DER) have
public offering becomes the main goal for the
simultaneous impact to the value of stock owned by the
industry, Taiwanese government still have the role as
government. Partially, the T test result shows that P/E
and ROA have no significance impact to the value of the
the share holder of biotechnology and medical-
stock owned by Government, while DER has significance related companies [11]. The government ownership
impact to the value of the stock owned by Government. in these companies may have designated purposes
the result is shown that the Taiwanese Government do about market establishment. In term of establishing
not fully consider the financial performance aspect as the new market, Government incentives and
their decision to own these companies' stocks. involvement could help company to acquire the
Index Terms—Stock, Government, Biotechnology and suitable business environment. The government can
medical-related companies, Financial Performance
lead in providing risk capital when the venture
capital industry is not yet developed, and may serve
I. INTRODUCTION
as a large monitoring shareholder when institutional
The purpose of this research is measuring the investors have not yet reached the critical threshold
impact of financial performance of biotechnology and of share ownership [8].
medical-related companies listed on Taiwan Stock Biotechnology and Medical-related Companies in
Exchange market represented by Debt to Equity ratio Taiwan has strategic position as promising and
(DER), Price Earnings Ratio (P/E) and Return on profitable industry. The importance and growth of
Asset Ratio (ROA) to its Value of Stock Owned by the biotechnology industry has, in recent years,
Government of Taiwan which determined by the book increased dramatically; it is now Taiwan’s second
value from government ownership most profitable industry, the high-
percentage to the equity of the companies. The tech industry being the highest [7]. Up to 2007,
biotechnology and medical-related companies have Taiwanese pharmaceutical industry returned
been forecasting to be one of Taiwan economic NT$66.0 billion with 368 companies active in this
backbone in the future. In 2006, the total annual sector. The medical devices industry returned
revenue for these industries in Taiwan was nearly NT$69.7 billion coming from 397 companies [4].
II. REFERENCES
Taiwanese government itself has strong A. Biotechnology and Medical-related Companies in
commitment on the Industry’s development in Taiwan
facilities, education, investment and regulations. As Biotechnology and Pharmaceutical Industries
the result, more than 1.000 biotechnology and Program Office’s report (2007) defines
medical-related companies have grown in Taiwan Biotechnology as an integrated science of a multi-
while the stakeholders in this industry plan to grow up research field. It can be seen as a basic tool in
to $100 billion in size by 2020 [12]. researching life science, medical science, and
In nonprofit point of view, The biotechnology and agronomy [4]. In Taiwan, the technology range of
medical-related companies has several significant roles biotechnology industry can be formally categorized
for Taiwan. In 2007, the biotechnology workforce size into three dimensions: first, the biotechnology
was 37,144, of which 8570 were in the biotechnology industry (i.e., unique biochemistry, biomedical,
industry and 12,224 in the pharmaceutical industry [7]. agriculture, and environmental manufacturing and
The government's stock analysis on Biotechnology service), also called the narrow biotechnology
and Medical-related Companies is essential to measure industry, the pharmaceutical industry, and the
the rationality of their stock ownership. The medical devices industry [7]. In 2006, the total
government ownership in these companies may annual revenue for these industries in Taiwan was
indicates the companies' ways of working . The nearly NT$179.1 billion, of which NT$43.4 billion
government backed companies are usually related to came from biotechnology, with 434 companies. The
the poor governance structure in the process of government's emphasis on higher education and
running their business. The example of the governance research, Taiwan has trained a diverse pool of talents
structure of government-linked companies (GLCs) is in the scientific and technical fields, which is what is
Temasek Holdings Singapore, the government holding required to drive innovations in multidisciplinary
entity, which typically owns substantial cash flow biomedical research [17]. Biotechnology and
rights but has disproportional control rights and medical-related companies in Taiwan enjoy the
exercises no operational control support from the government such as tax benefits,
[8]. Furthermore, the research from Jui-Kuei Regulations for Providing Assistance in the
Chen and I-Shuo Chen in 2008 shows that Taiwanese Development of New Leading Products , A+
biotechnological product prestige and market share are Industrial Innovative R&D Program , Small Business
decreasing due to the poor quality of products and Innovation Research Program(SBIR) , Industrial
technology from some of companies [7].
Technology Innovation Center Program (MNCD),
The promising forecast of the Taiwanese
National Development Fund, Small and Medium
Biotechnology and Medical-related is necessary to be
Enterprise Credit Guarantee Fund and loan for
discussed. The economics rationality of Taiwanese
promotion purposes [5].
Government in stock ownership can be one indicator
of its investment appropriateness. Companies'
financial performance represented by asset, equity and B. Government Ownership On The Company’s Stock
liability compared by value of stock owned by The Literature mentions several reasons of state-
Government can be a basic tools to delineate how backed company establishment. The state-backed
significance does the economics rationality influences company has purpose to create Employment
the Taiwanese government to own the stock. Opportunities, ensuring Economic Growth, provide
Therefore, the hypothesis of this research are as huge capital for emerging market, Protection of the
following : 1. H1 : Price-Earnings ratio (P/E) has Country’s Sovereignty and To Prevent Exploitation
significant impact to the government ownership , H2 : [16]. The Taiwanese Government ownership to
Return on Asset (ROA) Ratio has significant impact to the stock of biotechnology and medical-related
the government ownership, 3. H3 : Debt to Equity companies itself has strong justification in
ratio (DER) has significant impact to the government economics, social and politic point of view. In
ownership. economics point of view, Taiwanese government
would put Biotechnology and Medical industry as
their strategic industry that have comparative
advantage in Asian region. In 2016 Taiwanese
government reported that Total bio-related IPO market (TWSE) as the institution to regulate interior stock
value is 749.3 billion Taiwan Dollar (TWD) , market. The TWSE was established in 1961 and
Total revenue is 222.7 billion TWD and 9 new began operating as a stock exchange on 9 February
Mergers & Acquisitions events [5]. 1962. It is regulated by the Financial Supervisory
In social and political point of view, Taiwanese Commission (TWSE). Taiwan Capital market has
government use this industry as the main part of their 907 of Listed Companies for stock in 2017 [18].
national healthcare insurance for the citizen. Historically, the Taiwan Stock Market (TWSE)
Healthcare in Taiwan is administered by the Ministry reached an all time high of 11253.11 in January of
of Health and Welfare of the Executive Yuan. As 2018 and a record low of 3446.26 in October of 2001
with other developed economies, Taiwanese people [19].
are well-nourished but face such health problems as
chronic obesity and heart disease. In 2002 Taiwan
D. Financial Performance
had nearly 1.6 physicians and 5.9 hospital beds per
Financial performance is the depiction of the
1,000 population [10].
company’s operational activity to create the
The biotechnology and medical companies are
profitability. It is a subjective measure of how well a
also the a vital part of the national health sector.
firm can use assets from its primary mode of
Taiwan has the National health insurance program
business and generate revenues. This term is also
known as National Health Insurance Administration
used as a general measure of a firm's overall financial
(NHIA). It is defined as a financial and insurance
health over a given period of time, and can be used to
public enterprise and expanded into a comprehensive
compare similar firms across the same industry or to
social insurance system that offered universal
compare industries or sectors in aggregation [15]. It
coverage based on the principles of sustainability and
can be measured by analyzing the ratios of
caring for the disadvantaged [14].
company’s financial report and usually compare it
The health sector is also used by Taiwanese
with the average performance of Industry and
Government as the diplomatic tool to the
standard of Regulator.
International theatre. After Taiwan has been
Financial performance can be measured by
excluded since 1972 when the United Nations seated
Financial report analysis. It is the measurement or
the People’s Republic of China (PRC) as the
calculation of the financial performance. It refers to
government representing China. Taiwan known as
an assessment of the viability, stability and
Republic of China (ROC) faces international
profitability of a business, sub-business or project
isolation to the Taiwan authority over Chinese
[13]. Financial report analysis will translate the
territory. Beginning in 1997, the Foundation of
ratios from the financial report and give the depiction
Medical Professionals Alliance in Taiwan (FMPAT)
about the condition of the company. It is useful to
led efforts for admission as an observer in the World
analyze the company strength due to the stress
Health Assembly (WHA), the plenary body of the
factors in business and the bankruptcy prediction in
World Health Organization (WHO) [9].
the future. The ratios that are commonly used are :
Taiwan has some achievements toward its
The debt-to-equity ratio (D/E) to indicate the relative
involvement to the WHO effort on diseases outbreak
proportion of shareholders' equity and debt used to
over the nations. For example, In 2014, Taiwan
finance a company's assets. Return on Asset (ROA)
donated to the Pan American Development
that divide the return that company has earned in a
Foundation and Pan American Health Organization
period ( usually in one year) to its total asset and
for regional preparations for a possible Ebola
price to earnings ratio (P/E) to measure the price of
outbreak [6].
company’s stock to its earnings per share [15].
Table I
B. Data, Sources and Method of Analysis
This research is using the Secondary data from TW Result of Regression Analysis
Incorporated [11]. This research uses SPSS as the tool
analysis and then uses Multi-linear regression with R
Square test, F test and T test method of data analysis to
measure the impact of the financial performance
variable represented by DER, ROA and PER to the
Value of stock owned by the government.
C. Research Framework
\
1
Abstract—Riset tentang pengolahan kembali limbah bittern memajukan bidang riset teknologi aplikatif dari hulu ke hilir
telah banyak dilakukan oleh berbagai bidang keilmuan di di Indonesia.
Indonesia. Salah satunya pemanfaatan kembali Magnesium hasil
recycle limbah bittern. Faktanya sekitar 60% Magnesium
II. DASAR TEORI
dibutuhkan tulang sebagai unsur penguat. Berdasarkan riset-
riset yang dilakukan sebelumnya, terbukti tulang yang Berdasarkan penelitian terdahulu, ada beberapa hal yang
terdefisiensi Magnesium berpotensi tinggi mengalami dapat menjadi tinjauan pustaka terkait mengapa Magnesium
osteoporosis[19]. Berbagai penelitian tentang Magnesium dalam adalah salah salah satu unsur penting dalam upaya
bidang ortopedi dalam satu dekade ke belakang membuktikan menghasilkan produk-produk futuristik yang berguna bagi
bahwa Magnesium berpotensi untuk menciptakan industri dan kehidupan manusia.
komoditas futuristik. Karena selain murah dan melimpah, juga A. Magnesium sebagai Unsur Kaya Manfaat
ramah lingkungan. Pemanfaatan lainnya yang tak kalah Magnesium (Mg) menjadi elemen ke-8 paling banyak
fenomenal yaitu sebagai bahan alternatif post-LIBs energy ditemui di bumi. Menempati sekitar 2% dari keseluruhan
storage yang potensial. Magnesium memiliki theoretical massa kerak bumi. Selain itu Mg juga merupakan unsur
volumetric capacity sekitar 3.833 mAh/cm3, tentunya jauh lebih terbanyak ketiga yang terlarut dalam air laut, dengan
besar dibandingkan Lithium (sekitar 2.046 mAh/cm3), meski konsentrasi sekitar 0.13%. Oleh karenanya Mg murni maupun
masih memiliki banyak tantangan hingga dapat diaplikasikan di paduan senyawa Mg dapat disintesis melalui pemurnian air
luar laboratorium. Dari hasil riset, terbukti Magnesium menjadi laut, yang biasanya bersumber dari sumur/tambak garam, juga
salah satu solusi alternatif potensial dalam menciptakan produk-
limbah bittern. Manfaat dari unsur Mg ini sangat luas, baik
produk futuristik. Apalagi bagi Indonesia, yang oleh Badan
Mg murni maupun oksida-Mg, seluruhnya dapat berguna
Informasi Geospasial (BIG) disebut memiliki pesisir pantai
sebagai produk-produk tepat guna. Contohnya oksida-Mg
sepanjang 99.093 km. Hal ini menjadikan Indonesia sebagai
negara yang potensial untuk mengolah pertambakan garam.
sebagai bahan utama batu tahan api dalam tanur pelelehan besi
Jika tambak garam menjadi industri populer, bukan tidak dan baja, logam non-ferrous, gelas, dll. Selain itu Mg juga
mungkin limbah bittern yang biasanya hanya dimanfaatkan berguna sebagai bahan utama di industri agrikultur, kimia dan
sebagai biang garam, akan menjelma menjadi bahan utama obat-obatan, konstruksi, manufaktur dan permesinan, hingga
pemurnian mineral-mineral berguna yang dapat diolah menjadi ortopedi[21]. Apalagi dalam beberapa puluh tahun terakhir,
produk-produk futuristik, contohnya produk berbahan dasar Magnesium juga dimanfaatkan sebagai bahan alternative post-
Magnesium. LIBs energy storage[13][9].
Index Terms—Bahan, baterai, bittern, energy storage, implan Paduan Mg-Fe-Ca sebagai Implan Tulang Biodegradable
tulang, Magnesium, tambak garam Bahan yang digunakan dalam studi tentang Magnesium
sebagai bahan utama paduan Mg-Fe-Ca yang telah dilakukan
I. PENDAHULUAN sebelumnya adalah Magnesium murni (bubuk ≥99%, Sigma
Pada karya tulis ini akan terdapat tiga bagian penting yang Aldrich), Kalsium (granular ≥99%, Sigma Aldrich), Besi
akan diulas. Yang pertama adalah gambaran umum tentang (diambil dari pelat baja <0.06%C dan di-treatment hingga
penelitian-penelitian yang telah penulis lakukan untuk mencapai kemurnian ±99.9%, diuji menggunakan Optical
memanfaatkan unsur Magnesium sebagai bahan utama dalam Emission Spectroscopy). Bahan-bahan tersebut dicampur dan
pengembangan produk futuristik, baik yang berupa studi dipadukan dengan menggunakan horizontal furnace pada
pustaka, maupun eksperimental. Selanjutnya diikuti dengan temperatur 850ºC dan di-holding selama satu jam dalam
gambaran kondisi kekinian dari proses pengolahan limbah atmosfer vakum. Eksperimen tersebut menghasilkan tiga jenis
bittern di Indonesia. Dan yang terakhir adalah solusi yang komposisi paduan Mg-0.1Fe-Ca; Mg-0,2Fe-Ca; dan Mg-
penulis tawarkan untuk memberikan gambaran peluang 0,3Fe-Ca, dalam ±40 gram sampel, yang penampakan
sinergi antara hasil eksperimen skala laboratorium yang telah morfologinya ditunjukkan oleh Gbr. 1 diambil menggunakan
penulis lakukan, kondisi kekinian recycling Magnesium dari Electron Microscope dengan perbesaran 500X. Dalam gambar
limbah bittern, dan peran masyarakat–industri–pemerintah tersebut nampak jelas bahwa paduan kedua memiliki butir
sebagai pengambil kebijakan, yang dihubungkan oleh peran (grain) yang lebih banyak dibandingkan paduan pertama dan
serta perguruan tinggi (mengadopsi metode triple helix[12]) kedua. Lalu, korelasi antara paduan pertama, kedua, dan
dalam pengembangan produk-produk futuristik demi ketiga dengan compressive strength sebagai sifat mekanik
2
paduan Mg-Fe-Ca ditunjukkan pula dalam Tabel 1, beserta pengembangan teknologi baterai saat ini masih menyandarkan
perbandingan compressive strength dari cortical bone diri pada LIBs. Belum lagi tantangan-tantangan lainnya yang
manusia. berkaitan dengan risiko keamanan LIBs yang menjadi isu
yang belum terselesaikan hingga kini[2].
Untuk menjawab tantangan tersebut teknologi Mg-based
energy storage atau biasa juga disebut Mg-ion based batteries
(MIBs) mendapatkan perhatian khusus dari para peneliti di
bidang baterai dan energy storage[4][15]. Dengan berbagai
keuntungan yang dimiliki, selain harganya yang murah, Mg
juga berlimpah, memiliki reaktivitas yang lebih rendah
(terhadap udara di atmosfer) daripada Lithium, serta besarnya
theoretical gravimetric capacity yang dimiliki (sekitar 2234
mAh/g, dengan kemampuan transfer dua elektron
sekaligus)[6][14]. Terlebih lagi, ketika dipasangkan dengan
elektrolit yang tepat, reversible reaction dari pergerakan ion
Mg2+ pada MIBs bisa mendekati angka efisiensi hingga 100%
tanpa mengalami pembentukan struktur dendritik seperti
reaksi yang ditimbulkan dari pergerakan dan penetrasi ion Li+
pada LIBs[3][11].
Magnesium dalam MIBs pada umumnya berperan sebagai
anoda (elektroda negatif) dalam bentuk Mg ribbon atau logam
Mg murni, karena sifatnya yang less reactive jika
Gbr. 1. Penampakan struktur mikro paduan a) paduan Mg- dibandingkan dengan logam Li. Oleh karenanya, yang
0.1Fe-Ca; c) Mg-0,2Fe-Ca; dan c) Mg-0,3Fe-Ca. biasanya menjadi topik hangat dalam pengembangan MIBs
adalah pada katoda (elektroda positif) atau elektrolitnya, yang
TABEL 1 hingga saat ini masih menjadi topik hangat untuk terus digali
AVERAGE COMPRESSIVE STRENGTH DARI PADUAN MAGNESIUM
DIBANDINGKAN CORTICAL BONE lebih jauh[7]. Di banyak penelitian selama lebih dari satu
Spesimen Average Compressive strength (GPa) dekade ke belakang, Molybdenum dan Mangan masih menjadi
Mg-0,1Fe-Ca 143,4 dua unsur yang menempati posisi tertinggi sebagai supporting
Mg-0,2Fe-Ca 164,7 system bagi MIBs pada posisi katoda, baik Molybdenum
Mg-0,3Fe-Ca 145,9 dalam bentuk sulfida maupun Mangan dalam bentuk oksida
Mg–2Ca 235.7[8]
dalam berbagai state. Sebagai contohnya adalah Mo6S8,
Mg–4Ca 250.7[8]
Cortical Bone 130–180[20] Mo3S4(x-), MoS2,Mn3O4, MnO2, dll[2][4][10][22].
Pada Gbr. 2 dan Gbr. 3 ditunjukkan adalah hasil
Dari Tabel 1 dan Gbr. 1 dapat diketahui hubungan antara eksperimen charge-discharge pada MIBs dengan
ukuran butir secara kualitatif dengan average compressive menggunakan MoS2 sebagai katoda dan dengan
menggunakan elektrolit standar MIBs (untuk saat ini), yaitu
strength dari paduan Mg-Fe-Ca. Semakin banyak butir yang
all-phenyl-complex (APC) dengan ion Li+ sebagai aditif.
ada dalam paduan, memiliki kecenderungan compressive
Hasilnya menunjukkan MoS2 dapat bekerja lebih baik dengan
strength yang lebih tinggi. Korelasi antara persentase unsur
kapasitas lebih tinggi (>160 mAh/g) dibandingkan dengan
besi (Fe) dengan struktur mikro yang dihasilkan nampak Mo6S8 (±145 mAh/g[22]). Terlebih lagi, MoS2 memiliki
dalam Gbr. 1, semakin tinggi jumlah Fe yang ada dalam kapasitas yang lebih stabil dalam 200 cycle dengan capacity
paduan akan berpengaruh terhadap peningkatan area dari batas retention di atas 85% dan coulombic efficiency >99%[2].
butir. Jadi, dapat diartikan bahwa unsur Fe dalam paduan akan
meningkatkan ukuran butir, meski tidak mempengaruhi secara
signifikan pada compressive strength. Dan berdasarkan hasil
yang didapatkan, maka dapat disimpulkan bahwa Mg-0,2Fe-
Ca memiliki compressive strength yang lebih tinggi
dibandingkan paduan lainnya[16].
III. METODE
Dalam melakukan sinergi antara 1) hasil eksperimen skala
laboratorium yang telah penulis lakukan; 2) kondisi kekinian
recycling Magnesium dari limbah bittern; 3) dan upaya
maksimalisasi peran dari masyarakat–industri–pemerintah
sebagai pengambil kebijakan, yang dihubungkan oleh peran
Gbr. 3. Cyclic stability dari berbagai katoda yang di-charge-
serta perguruan tinggi dalam pengembangan produk-produk
discharge menggunakan current rate 100 mA/g.
futuristik berbahan dasar Magnesium, maka penulis
menawarkan pengadopsian nyata dari metode triple helix.
Berdasarkan beberapa hasil riset di atas, telah jelas bahwa Pada awalnya pemerintah (komponen helix pertama) dapat
Magnesium layak menjadi unsur andalan dalam upaya melakukan pemetaan terhadap perguruan-perguruan tinggi
pengembangan produk-produk futuristik yang nantinya bisa (helix kedua) yang mampu memberikan sumbangsing nyata
menjadi warna baru dalam komoditas unggulan di Indonesia. dalam memperbesar kemungkinan penerapan aplikatif yang
Apalagi jika didukung dengan ulasan-ulasan tentang lebih besar untuk pengolahan limbah bittern untuk
gambaran umum bagaimana Indonesia bisa jadi negara yang menghasilkan Magnesium. Setelah mengetahui pemetaan dari
potensial dalam menghasilkan unsur Magnesium berikut. komponen-komponen helix kedua maka helix pertama
bisa melanjutkan dengan melakukan listing daftar beserta
B. Gambaran umum Potensi Limbah Bittern di Indonesia rincian jumlah industri-industri potensial (helix ketiga)
Bittern dikenal sebagai limbah yang dihasilkan selama yang menempati area penghasil garam atau bahkan
proses kristalisasi garam di tambak. Selama ini bittern dibuang yang diproyeksikan akan menempatinya di masa mendatang.
atau dicampurkan kembali dengan air laut untuk Untuk selanjutnya kita adakan pendalaman konsep lebih
mempercepat penuaan air dalam proses pembuatan garam. Di lanjut, berupa perencanaan proyek yang akan dikerjakan
dalam bittern terkandung sekitar 3.42% Magnesium[5]. bersama-sama antara kolaborasi tiga helix yang telah
Sebagai contoh, produksi garam di Jawa Timur (Jatim) terpetakan[18]. Tentunya dengan melibatkan petani garam
hingga mendekati akhir bulan Agustus 2017 mencapai (masyarakat) sebagai bagian dari daya dukung utama dari
helix kedua, yang secara skematikanya diperlihatkan
melalui Gbr. 4. Pada skema tersebut jelas sekali bahwa
4
masyarakat merupakan inti dari helix yang menjadi pelaku yang tinggi dan quality control yang baik, maka prosesnya
kolaborasi ini (karena pada dasarnya masing-masing helix akan dapat diteruskan menuju ke arah pemasaran produk
merupakan bagian dari masyarakat). (rencana jangka panjang).
Dalam melakukan prosedur pemasaran, nantinya (untuk
produk implan tulang) dapat dikoordinasikan dengan
Kementerian Kesehatan melalui sebuah kampanye mengenai
penggunaan implan tulang biodegradable berbahan dasar paduan
Magnesium. Tentu saja kampanye tersebut dilakukan dengan
lisensi penuh dari Kementerian Kesehatan dan Dinas Kesehatan
di berbagai kota. Selain itu juga perlu dilakukan sebuah
kerjasama yang baik dengan Rumah Sakit yang memiliki
wewenang untuk melaksanakan penanaman implan tulang pada
tubuh pasien. Lalu untuk produk baterai, yang merupakan industri
dengan jangka yang lebih panjang, dapat memanfaatkan
konsorsium baterai yang telah terbentuk di Indonesia (contoh:
Konsorsium Nasional Baterai yang digawangi oleh LIPI,
BATAN, BPPT, B4T, UI, ITB, ITS, UGM, UNS, Universitas
Lambung Mangkurat dan Kementerian Perindustrian) untuk
selanjutnya merancang riset aplikatif di masing-masing institusi.
Gbr. 4. Skema triple helix yang diadopsi dalam kolaborasi Setelah risetnya berjalan, maka dapat dikontrol secara lebih
pemerintah-perguruan tinggi-industri untuk menciptakan sistematis melalui focus group discussion (FGD) dan konferensi
atmosfer industrial technology berbasis masyarakat tahunan. Sehingga produk baterai buatan Indonesia dengan
memanfaatkan bahan-bahan dan sumber daya alam Indonesia
dapat tercipta sesegera mungkin di masa depan, tentunya dengan
IV. PEMBAHASAN daya dukung penuh dan gelontoran dana utama dari pemerintah
Kolaborasi dari fakta-fakta yang ada seperti 1) unsur Republik Indonesia melalui Kementerian Riset, Teknologi, dan
Magnesium yang kaya manfaat; 2) beberapa hasil riset potensial Pendidikan Tinggi.
untuk menciptakan produk futuristik seperti implan tulang Selain itu, kerjasama juga dapat dilakukan antara
biodegradable dan baterai; 3) potensi Indonesia, yang menurut Pemerintah Provinsi dari masing-masing daerah yang
Badan Informasi Geospasial (BIG) disebut memiliki pesisir memiliki tambak garam, Pusat Penelitian dan Pengembangan
pantai sepanjang 99.093 km, dapat dimanfaatkan sebagai modal Sumber Daya Laut dan Pesisir (P3SDLP), Kementerian
awal untuk menjadikannya sumber utama limbah bittern; serta 4) Kelautan dan Perikanan, serta lembaga lain yang terkait dalam
kemungkinan pengadopsian metode triple helix dalam upaya menggencarkan pengolahan limbah bittern menjadi
memberikan ruang sinergi antara pemerintah-perguruan Magnesium agar bahan baku dari pembuatan produk-produk
tinggi-industri untuk menciptakan atmosfer industrial futuristik berbahan dasar Magnesium dapat selalu tersedia dari
technology berbasis masyarakat, bisa jadi akan memunculkan hasil daur ulang limbah bittern. Sehingga akan timbul
sebuah kesempatan bagi Indonesia untuk mewujudkan satu kesinambungan antara peningkatan aktivitas pertambakan
sumber inspirasi industri baru yang menyandarkan pada garam yang secara otomatis berdampak positif bagi industri
material unik bernama Magnesium. garam rakyat nasional dan peningkatan nilai ekonomi dari
Untuk menjadikan seluruh fakta tersesbut saling terkoneksi limbah bittern yang akan menciptakan pemasukan tambahan
secara nyata, maka semua pihak dalam helix dapat mulai bagi petani garam (masyarakat).
memikirkan tentang blueprint yang akan menjadi pondasi dari
masing-masing peran. Pemerintah seharusnya mulai V. KESIMPULAN
memikirkan regulasi tentang tata niaga serta perlindungan
Telah banyak fakta-fakta yang mendukung dan
terhadap harga dasar Magnesium hasil olahan limbah garam.
Lalu untuk perguruan tinggi, dapat lebih meningkatkan peran memperkuat pengembangan produk berbahan dasar
serta dengan melakukan lebih banyak survei-survei terkait Magnesium, terutama sebagai bahan dasar produk-produk
pertambakan garam hingga kondisi lapangan kesejahteraan futuristik seperti implan tulang biodegradable dan Mg-ion
petani garam (masyarakat), serta menggencarkan based batteries (MIBs). Apalagi dengan adanya bahan utama
pengembangan riset-riset potensial yang telah ada menjadi untuk mendukung ketersediaan Magnesium di dalam negeri
teknologi yang lebih aplikatif untuk meningkatkan efisiensi berupa hasil recycling limbah bittern dari tambak garam yang
dari produksi Magnesium yang berasal dari limbah bittern. ada di seluruh pesisir Indonesia. Hal itu semakin
Untuk industri, bisa jadi dimulai dengan merancang rumusan mengukuhkan bahwa industri pengolahan Magnesium sebagai
mekanisme fund and share terkait teknologi recycling bahan utama produk-produk futuristik adalah sebuah
Magnesium dari pengolahan limbah bittern ini.
keniscayaan. Oleh karenanya, hanya dengan kolaborasi
Nah, ketika itu semua telah dilakukan dan pondasi dari
kolaborasi ini telah kuat, maka dapat dimulai pelaksanaan peran menggunakan metode triple helix untuk menciptakan atmosfer
masing-masing helix. Lebih jauh lagi ketika produk setengah jadi industrial technology berbasis masyarakat maka wujud nyata
berupa Magnesium telah tersedia, maka pengolahan advance dari sinergisitas ini akan segera nampak dan terlaksana di
untuk menciptakan produk-produk semacam implan tulang masa depan sebagai jawaban dari cita-cita Indonesia yang
biodegradable dan baterai berbasis MIBs dapat dilakukan mandiri dan berdikari teknologi.
dengan semakin masif. Selanjutnya setelah produk akhir mulai
dapat diproduksi secara berkala, tentunya dengan standardisasi
5
VI. DAFTAR PUSTAKA [20] S. V. Dorozhkin, "Calcium orthophosphate coatings on magnesium and
[1] B. Sholikah, F. Yolanda. (2017). Sampai Agustus, produksi garam Jatim its biodegradable alloys," Acta Biomaterialia 2014, vol. 10, pp. 2919-
9.037 ton. Dipublikasikan dalam harian online Republika. [Online]. 2934, Mar. 2014.
https://www.republika.co.id/berita/nasional/daerah/17/08/30/ovhw1g370- [21] U.S. Geological Survey. (2018). Magnesium Statistics and Information.
sampai-agustus-produksi-garam-jatim-9037-ton U.S. Department of the Interior, Reston, Virginia. [Online]. Available:
[2] C. J. Hsu, C. Y. Chou, C. H. Yang, T. C. Lee, J. K. Chang, https://minerals.usgs.gov/minerals/pubs/commodity/magnesium/
"MoS2/graphene cathodes for reversibly storing Mg2+ and Mg2+/Li+ in [22] X. Chen, F. L. Bleken, O. M. Løvvik, F. Vullum-Bruer, "Comparing
rechargeable magnesium-anode batteries," Chemical Communication electrochemical performance of transition metal silicate cathodes and
2016, vol. 52, 1701-1704, Dec. 2015. chevrel phase Mo6S8 in the analogous rechargeable Mg-ion battery
[3] D. Aurbach, Y. Cohen, M. Moshkovich, "The study of reversible system," Journal of Power Sources 2016, vol. 321, pp. 76–86, Jul. 2016.
magnesium deposition by in situ scanning tunneling microscopy,"
Electrochemical Solid-State Letters 2001, vol. 4, pp. A113-A116, Jun.
2001.
[4] D. Aurbach, Z. Lu, A. Schechter, Y. Gofer, H. Gizbar, R. Turgeman,
Y.Cohen, M. Moshkovich, E. Levi, "Prototype systems for rechargeable
magnesium batteries," Nature 2000, vol. 407, pp. 724–727, Oct. 2000.
[5] D. Saepuloh. (2013). Peluncuran Teknologi Pengolahan Limbah
“Bittern” menjadi padatan Magnesium dan Sistem Informasi Garam
Rakyat oleh Wakil Gubernur Jawa Timur. Dipresentasikan dalam
pembukaan dan peluncuran teknologi pengolahan limbah bittern Jawa
Timur. [Online]. http://p3sdlp.litbang.kkp.go.id/
[6] H. D. Yoo, I. Shterenberg, Y. Gofer, G. Gershinsky, N. Pour, D.
Aurbach, "Mg rechargeable batteries: an on-going challenge," Energy &
Environmental Science 2013, vol. 6, pp. 2265-2279, May 2013.
[7] H. Kuwata, M. Matsuia, N. Imanishi, "Passivation layer formation of
magnesium metal negative electrodes for rechargeable magnesium
batteries," Journal of The Electrochemical Society 2017, vol. 164, pp.
A3229-A3236, Oct. 2017.
[8] H. R. Bakhsheshi-Rad, M. H. Idris, M. R. Abdul-Kadir, A. Ourdjini, M.
Medraj, M. Daroonparvar, E. Hamzah, "Mechanical and bio-corrosion
properties of quaternary Mg–Ca–Mn–Zn alloys compared with binary Mg–
Ca alloys," Materials and Design 2014, vol. 53, pp. 283–292, Jul. 2013.
[9] I. Shterenberg, M. Salama, Y. Gofer, E. Levi, D. Aurbach, "The
challenge of developing rechargeable magnesium batteries," Materials
Research Society Bulletin 2014, vol. 39, pp. 453-460, May 2014.
[10] J. Richard, A. Benayad, J. F. Colin, and S. Martinet, "Charge transfer
mechanism into the chevrel phase Mo6S8 during Mg intercalation," The
Journal of Physical Chemistry C 2017, vol. 121, pp. 17096–17103, Jul.
2017.
[11] M. Matsui, "Study on electrochemically deposited Mg metal," Journal of
Power Sources 2011, vol. 196, pp. 7048-7055, Aug. 2011.
[12] M. Ranga. (2011). The Triple Helix Concept. Triple Helix Research Group,
Stanford, California. [Online]. Available:
https://triplehelix.stanford.edu/3helix_concept
[13] M. S. Park, J. G. Kim, Y. J. Kim, N. S Choi, J. S. Kim, "Recent advances
in rechargeable magnesium battery technology: a review of the field's
current status and prospects," Israel Journal of Chemistry 2015, vol. 55,
pp. 570 – 585, Mar. 2015.
[14] N. Yabuuchi, K. Kubota, M. Dahbi, S. Komaba, "Research Development
on Sodium-Ion Batteries," Chemical Reviews 2014, vol. 114, pp. 11636–
11682, Nov. 2014.
[15] P. Saha, M. K. Datta, O. I. Velikokhatnyi, A. Manivannan, D. Alman, P.
N. Kumta, "Rechargeable magnesium battery: current status and key
challenges for the future," Progress in Materials Science 2014, vol. 66,
pp. 1-86, Oct. 2014.
[16] R. F. H. Hernandha, A. Purniawan, Y. Setiyorini, "Micro-structure and
compressive strength correlation analysis of Mg-Fe-Ca alloy as
biodegradable material for orthopedic devices application," in Proc. 2016
the 2nd International Seminar on Science and Technology (ISST), pp.
245-246.
[17] R. F. H. Hernandha. (2015). Perbolant, implan tulang permanen
biodegradable berbahan dasar paduan Magnesium-Kalsium berpori
sebagai solusi alternatif penyalur hasil pengolahan limbah bittern pada
tambak garam di Jawa Timur. Dipresentasikan dalam kompetisi karya
tulis Writing Competition Beswan Djarum 2014/2015 regional. Surabaya,
Jawa Timur (Sep. 2015)
[18] R. F. H. Hernandha. (2018). Belajar dari Taiwan, Triple Helix yang
Mampu Dijalankan. Dipublikasikan dalam kompetisi blog opini pada
agenda tahunan Indonesia Development Forum 2018. [Online].
https://indonesiadevelopmentforum.com/2018/blog/4692-belajar-
dari-taiwan-triple-helix-yang-mampu-dijalankan
[19] S. Castiglioni, A. Cazzaniga, W. Albisetti, J. A. M. Maier, "Magnesium
and osteoporosis: current state of knowledge and future research
directions," Nutrients 2013, vol. 5, pp. 3022-3033, Jul. 2014.
1
Abstract—Petunjuk Permasalahan penyediaan air minum bagi analisis menunjukkan kualitas air Intake Tabanggale telah
warga Kota Kendari saat ini sangat mendesak dicari solusinya memenuhi nilai mutu untuk air baku, air bersih, dan air minum.
seiring dengan perkembangan kota dan pertambahan penduduk.
Distribusi air bersih di kota Kendari tidak merata dengan Index Terms—PDAM Kendari, SPAM Kendari, Intake
jumlah cakupan daerah pelayanan air minum tiap tahun Tabanggele
menurun hingga mencapai 21,96 persen. Disisi lain perencanaan
yang dilakukan belum optimal. Ketidakmampuan PDAM Tirta I. PENDAHULUAN
Anoa Kota Kendari untuk memenuhi kebutuhan air bersih bagi
pelanggan berdampak pada menurunnya jumlah pelanggan tiap 1.1 Latar belakang
tahun, sementara ketersediaan sumber air baku cukup besar. Perkembangan Kota Kendari sebagai ibukota
Ketidak mampuan PDAM Kendari diakibatkan karena Provinsi Sulawesi Tenggara dengan luas 267,37 km2 dan
kurangnya kapasitas produksi air bersih yang saat ini hanya jumlah populasi 359.371 jiwa (BPS Kota Kendari, 2018)
mencapai 297 L/detik. Selain itu kondisi jaringan pipa yang dengan kepadatan penduduknya yang mencapai 1.215
sudah tua mengakibatkan kebocoran yang cukup tinggi sehingga jiwa/km2 menimbulkan permasalahan dalam penyediaan air
kehilangan air mencapai 61,87 persen. Untuk mengatasi hal
2minum untuk keperluan pokok sehari-hari warganya.
tersebut dibutuhkan jaringan distribusi air bersih yang baik dan Sistem penyediaan air minum (SPAM) Kota Kendari
mampu melayani kebutuhan air bersih bagi warga Kota
Kendari. Perencanaan pengembangan tersebut dibuat secara mengandalkan pasokan air baku yang berasal dari Sungai
utuh dan membentuk suatu sistem jaringan distribusi air bersih Pohara yang berada di daerah aliran sungai (DAS) Konaweha.
yang terpadu. Kapasitas produksi air baku dari Sungai Pohara tersebut tidak
Pembangunan Intake baru di Desa Tabanggele (Intake mencukupi kebutuhan air warga Kota Kendari yang semakin
Tabanggele) terusan DAS Konaweha merupakan salah satu
strategi pemerintah Kota Kendari untuk meningkatkan
meningkat.
kapasitas produksi air minum hingga 800 L/detik. Penelitian ini Cakupan pelayanan SPAM PDAM Kota Kendari pada
bertujuan menganalisis perhitungan kebutuhan air bersih, 2018 mencapai 21.96% dengan jumlah pelanggan yaitu 17.385
ketersediaan air meliputi kuantitas,kualitas dan kontuinitas
sambungan rumah tangga dari jumlah penduduk 359.371 jiwa.
sumber air, serta analisis hidrolis jaringan distribusi
perpipaannya menggunakan program Epanet. Kinerja PDAM menurut data audit BPKP pada BPPSPAM
Hasil perhitungan proyeksi dan analisis jumlah kebutuhan air belum optimal khususnya IPA Punggolaka (PDAM Tirta Anoa
minum Kota Kendari adalah 251,82 L/detik pada 2022 dan dengan intake di Sungai Pohara) yang memprioritaskan
379,59 L/detik pada 2027 dengan konsumsi air rata-rata sebesar
melayani 6 kecamatan dari 10 kecamatan di Kota Kendari
130 L/org/hari dengan jumlah pelanggan = 17,385 SR. Dengan
total kapasitas produksi PDAM Tirta Anoa sebesar 1097 L/detik (kecamatan Mandonga, Kendari, Kendari Barat, Wua-Wua,
yang meliputi intake Tabanggale 800 L/detik dan intake (lama) Kadia dan Puuwatu) dengan kapasitas produksi air minum
Sungai Pohara sebesar 297 L/detik. Ketersediaan air baku dari hanya sebesar 297 l/detik dari kapasitas desain 400 liter/detik,
pembangunan Intake Tabanggale pada 2022 sebesar 988.68
L/dtk dan 2027 sebesar 1008,43 l/dtk dinilai mampu mencukupi serta tingkat kehilangan air sebesar 61,87% yang melebihi
seluruh kebutuhan air bersih masyarakat Kota Kendari. Kondisi angka toleransi nasional kehilangan air sebesar 20 persen
aliran pada sistem jaringan pipa distribusi air dapat mengalir sedangkan kecamatan lainnya dilayani oleh PDAM Wanggu,
selama 8 jam/hari. Dari hasil simulasi juga menunjukkan nilai
PDAM Anggoeya, Matabondu dan PDAM Andounohu.
pressure (tekanan) node warna biru di beberapa junction bernilai
negatif sehingga menyebabkan kecepatan aliran berkurang. Uji Hal tersebut berdampak terhadap menurunnya jumlah
pelanggan tiap tahun. Sedimentasi lumpur tambang dan
2
aktivitas eksplorasi perkebunan sawit juga menambah 2. Data sekunder adalah data yang diperoleh secara tidak
permasalahan kualitas sumber air minum dari sungai-sungai langsung atau data yang dikumpulkan dan disatukan oleh
yang telah tercemar. studi-studi sebelumnya yang diterbitkan oleh berbagai
Analisis pengaruh penambahan debit kebutuhan dalam instansi terkait, yaitu data kependudukan, sosio ekonomi,
Perencanaan Intake baru Kota Kendari difokuskan terhadap data cuaca dan iklim, peta dasar, topografi, hidrologi, tata
optimalisasi strategi pengembangan jaringan SPAM (Sistem guna lahan, dan kondisi eksisting sistem air minum kota
Penyediaan Air Minum) Kota Kendari Sulawesi Tenggara kendari.
melalui pembangunan intake Tabanggele menuju one
integrated water treatment plan of Kendari City. 2.3 Metode Pengumpulan Data san Analisis
Metode pengumpulan data untuk penelitian ini dilakukan
1.2 Tujuan Penelitian dengan metode survei/observasi di lokasi penelitian,
1. Melakukan analisis pembangunan Intake Tabanggele wawancara, studi dokumentasi, studi kepustakaan yang
sebagai pengembangan Sistem Jaringan Distribusi Air selanjutnya dilakukan proses pengolahan dan analisis data
Minum di Kota Kendari. untuk menjawab rumusan masalah dan menjawab hipotesa
2 Menganalisis sistem jaringan air bersih PDAM Tirta yang telah diajukan. Analisis Data yang digunakan adalah :
Anoa dengan kondisi eksisting yang ada sekarang.
1. Analisis Geomorfologi, untuk mengetahui kondisi
morfologi daerah perencanaan, kondisi pola aliran sungai,
II. METODOLOGI PENELITIAN elevasi, sudut lereng, pola kontur, bentuk bukit, kerapatan
sungai, luas DAS dll.
2. Analisis data topografi, untuk mengetahui beda tinggi dan
2.1 Lokasi Penelitian
Penentuan wilayah pelayanan intake Tabanggele jarak antara sumber dengan pelayanan, jalur pipa
didasarkan pada potensial pengembangan pelayanan SPAM transmisi dan distribusi, rencana tapak bangunan (Intake,
perpipaan Kota Kendari 2016-2025, yaitu pada pelayanan WTP, Reservoir).
PDAM Tirta Anoa di 6 kecamatan yang memiliki tingkat 3. Analisis kuantitas sumber air baku di lokasi perencanaan,
kepadatan penduduk tinggi dan potensi populasi yang dapat dilakukan dengan perhitungan debit (Q) dari hasil
pengukuran luas penampang aliran (A) dan kecepatan
dilayani sangat signifikan, sehingga merupakan kecamatan
aliran (V). Rencana alokasi air baku lebih besar daripada
yang sangat potensial sebagai wilayah pengembangan
debit yang diperlukan, sekurang-kurangnya 130% dari
pelayanan PDAM.
kebutuhan air. Karena kondisi iklim sangat
mempengaruhi fluktuasi air baku baik dari aspek
kualitatif maupun kuantitatif, level air banjir, dan level air
minimum. Bilamana kapasitas pengambilan air baku tidak
dapat tercapai karena keterbatasan sumbernya akibat
musim kemarau, maka dilakukan konversi debit surplus
pada musim hujan menjadi debit cadangan pada musim
kemarau. Debit cadangan ini harus melebihi kapasitas
kebutuhan air minum.
4. Analisis perhitungan ketersediaan air (kontinuitas), untuk
menentukan besarnya air yang tersedia atau debit andalan.
Debit andalan sendiri adalah debit sungai yang bisa
Gbr. 1 Peta cakupan eksisting jaringan pipa distribusi PDAM Kota diandalkan dapat terjadi pada waktu-waktu tertentu. Debit
Kendari
andalan dipakai sebagai debit rencana untuk memenuhi
kebutuhan air minum. Perhitungan ketersediaan air/neraca
2.2 Data yang Digunakan
air (water balance) berfungsi untuk mengetahui apakah
Data yang digunakan dalam pengembangan
SPAM dengan perencanaan intake baru ini adalah data primer debit yang dibutuhkan untuk kebutuhan air dapat
dan data sekunder. mencukupi. Perhitungan neraca air dengan analisis data
1. Data primer adalah data yang diperoleh dari pengukuran hujan, data klimatologi dan analisis Mock yaitu dengan
langsung di lapangan , yaitu kondisi morfologi daerah mengurangkan debit yang tersedia dengan debit air yang
perencanaan debit maksimum, debit minimum, debit rata- dibutuhkan. Parameter-parameter dalam model Mock
rata, debit andalan, sedimen transport, kondisi topografi adalah sebagai berikut:
karakteristik/struktur tanah, kualitas air baku dan
a) Koefisien infiltrasi untuk musim kemarau (Cds) dan
kontuinitas air baku serta kontuinitas layanan.
musim penghujan (Cws).
3
perhari (q) dikali faktor hari maksimum (fmd = 1,05- 3.4 Analisis Ketersediaan Air
1,15)
Ketersediaan air di Daerah Aliran Sungai Konaweha
Q =Pxq (Pohara) penting untuk diketahui agar dapat dimanfaatkan
secara optimal dan bijaksana. Ketersediaan air yang relatif
Qmd = Q x fmd tetap namun kebutuhan air yang terus bertambah seiring
dengan pertambahan penduduk mendorong untuk
Kebutuhan harian max: dilakukannya analisis mengenai ketersediaan air di
= 1,1 x kebutuhan air rata-rata Daerah Aliran Sungai Konaweha (Pohara) di desa
Kebutuhan jam puncak Tabanggele, kec. Sampara.
= 1,5 x kebutuhan harian Analisis ketersediaan air pada penelitian ini
menggunakan model hidrologi Mock. Analisis potensi
ketersediaan air baku dilakukan dengan menganalisis
b. Hitung kebutuhan total air bersih (Qt), dengan factor
kuantitas sumber air. Kuantitas sumber air di analisis
kehilangan air dengan melakukan pengukuran langsung diapangan
25% dengan persamaan : Qt = Qmd terhadap beberapa parameter sumber air baku, yaitu:
x 100/80 a) Data penampang sungai, dilakukan
survei lapangan untuk mengumpulkan data
c. Bandingkan dengan hasil pengukuran debit sumber penampang sungai yaitu L (lebar airan) dan h
air baku apakah dapat mencukupi atau tidak, jika (kedalaman aliran). Pengukuran dilakukan
tidak mencukupi cari alternatif sumber baku lain. menggunakan meteran.
Dari hasil perhitungan kebutuhan air bersih di b) Data kecepatan aliran rata-rata, Pengukuran
Kecamatan Kendari, maka dapat dibuat tabel dilakukan pada ¼L, ½L, dan ¾L dengan
rekapitulasi kebutuhan air bersih (Domestik dan Non kedalaman 0,2h,
Domestik) seperti Tabel 1 berikut ini. 0,6h, dan 0,8h. Pengukuran dilakukan
Tabel. 1. Rekapitulasi Kebutuhan Air Bersih di PDAM Tirta Anoa
menggunakan current meter.
pada musim penghujan (bulan Desember – Mei) terjadi dari jam 16.00-00.00. Sisa tekanan disesuaikan dengan
kelebihan air yang cukup besar, yaitu pada bulan kondisi batas maksimal maka dikhawatirkan pada jam
Desember sebesar 69,800 l/detik dan bulan April sebesar puncak, sisa tekanan akan menurun melewati batas
135,500l/detik. minimal sehingga kebutuhan tidak dapat terpenuhi.
Pada Gambar 5 menunjukkan bahwa ketersediaan air
Hasil simulasi pada Gambar 3.4 terdapat beberapa
pada PDAM pusat (pohara) DAS Konaweha terjadi kelebihan
node yang tidak memenuhi standar tekanan. Semua node
air (surplus), sehingga masih dapat memenuhi kebutuhan air
sampai dengan akhir tahap I (2022) dan Tahap II (2027). yang letaknya berjarak dekat dengan pompa/booster/IPA
akan memiliki tekanan yang besar dikarenakan besarnya
head pada pompa distribusi yang terpasang. Besarnya
tekanan pada node dipengaruhi oleh head air yang
dikirim dari sumber utama. Dengan semakin menjauhi
sumber air maka tekanan akan semakin kecil karena
adanya energi friksi (pengurangan energi karena adanya
gesekan) antara fluida (air) dengan dinding pipa, tingkat
kekasaran (faktor umur pipa) dari dinding pipa,
turbulensi dalam fluida, perubahan diameter pipa,
pemasangan dari bend (belokan) maupun valve (katup)
Gbr. 5. Hubungan Ketesediaan Air Dengan Kebutuhan Air dan akibat dari kebocoran dapat menyebabkan
pengurangan nilai tekanan pada wilayah distribusi.
3.5 Analisis Hidrolika Dalam Sistem Jaringan Terdistribusi Gambar 6 berikut ini merupakan hasil simulasi tekanan
dan aliran pada PDAM Pohara.
Hasil running pada Epanet menunjukkan tanda/node
berwarna merah dan kuning yang berarti jaringan distribusi air
bersih berjalan lancar tanpa ada masalah (tabel lampiran hasil
running epanet). Dengan tekanan aliran yang cukup, seperti
pada junction 2 (tekanan sebesar 1046.04 m, head sebesar
1081.04 m, flow sebesar 105,76 LPS, dan velocity sebesar 3.4
m/s) sampai dengan junction 75 (tekanan sebesar 453.60 m,
head sebesar 781.94 m, flow sebesar 0.4 LPS, dan velocity
sebesar 0.2 m/s), dan junction 208 (tekanan sebesar 1025.99
m) sampai junction 264 sebesar (tekanan sebesar 483.04 m
head sebesar 490.04 m, flow sebesar 0.31 LPS, dan velocity
sebesar 0.07 m/s). Tekanan menurun disebabkan karena
adanya perbedaan elevasi pada lokasi tersebut. Pada model
jaringan memiliki peningkatan elevasi dari reservoir hingga
titik terjauh, hal ini dapat menyebabkan penurunan tekanan
secara signifikan. Tingginya tekanan juga dipengaruhi
oleh diameter pipa, semakin kecil diameter pipa maka
tekanan juga akan tinggi.
Dari hasil simulasi juga menunjukkan pressure
(tekanan) node warna biru dibeberapa junction bernilai
negatif, sehingga menyebabkan kecepatan aliran
berkurang yang berarti pipa kurang/tidak lancar atau
tidak dapat mengalirkan air secara baik ke seluruh untuk
wilayah pelayanan PDAM. Seperti pada junction 76
(dengan pressure sebesar -851.10 m head sebesar -
815.10 m, dan velocity sebesar 0.92 m/s) sampai dengan
junction 207 (tekanan sebesar - 2215.77 m). Pada hasil
simulasi program Epanet 2.0 dengan
operasional pompa ditargetkan 8 jam/hari yang dimulai
6
Gbr. 6. Distribusi jaringan perpipaan terhadap tekanan dan aliran pada daerah pelayanan PDAM Pohara Tirta Anoa
Gbr. 7. Hasil Running distribusi jaringan perpipaan terhadap tekanan dan aliran
7
4.1 Kesimpulan
V. DAFTAR PUSTAKA
Berdasarkan hasil analisis yang telah dilakukan pada bab Anonim. Departemen Pemukiman dan Prasarana
sebelumnya, maka dapat diambil kesimpulan sebagai berikut : Wilayah.2002. Pedoman / Petunjuk Teknik dan Manual.
1. Analisis pengembangan jaringan SPAM kota kendari Jakarta : Balitbang Departemen KimpraswiL
melalui pembangunan Intake Tabanggele harus
memenuhi cakupan pelayanan kebutuhan air bersih yang Anonim. DPU Ditjen Cipta Karya. 1987. Buku Utama
memenuhi syarat kualitas, kuantitas, dan kontinuitas, Sistem Jaringan Pipa. Diktat Kursus Perpipaan
yaitu: Departemen Pekerjaan Umum Direktorat
a. Dari hasil uji analisis kualitas air untuk semua Jenderal Cipta Karya Direktorat Air Bersih.
parameter yang diuji terlihat bahwa kualitas sumber air Jakarta : Departemen Pekerjaan Umum, Direktoral Jenderal
Cipta Karya, Direktorat Air Bersih.
baku pada Intake Tabanggele memenuhi baku mutu
sebagai air baku, air bersih atau air minum, Dari hasil Anonim. Peraturan Menteri Pekerjaan
uji tersebut maka diperlukan pengolahan sebagian agar Umum Nomor : 18/PRT/M/2007.
air baku sesuai dengan baku mutu air minum, unit
pengolahan yang dilakukan yaitu terdiri dari koagulasi, Pedoman Penyusunan Perencanaan Teknis Pengembangan
flokulasi, sedimentasi, filtrasi, dan desinfeksi. Sistem Penyediaan Air Minum. Jakarta :
b. Hasil perhitungan proyeksi dan analisis jumlah Departemen Pekerjaan Umum, Direktoral Jenderal Cipta
kebutuhan air minum Kota Kendari adalah 251,82 Karya
L/detik pada 2022 dan 379,59 L/detik pada 2027. Total
sumber air baku dari intake baru di desa Tabanggele Linsley,Ray K. & Joseph B. Franzini .1996. Teknik
dengan penambahan kapasitas produksi 800 l/detik Sumber Daya Air Jilid I dan II, Edisi Ketiga,
ditambah dengan kapasitas produksi dari intake sungai Terjemahan Ir. Djoko Sasongko, M.Sc., Jakarta
:Erlangga.
pohara (lama) 297 l/dtk yaitu sebesar 1097 l/dtk.
Bedasarkan total kebutuhan air bersih untuk PDAM Review Rencana Induk Sistem pengelolaan Air Minum Kota
Puuwatu tahun 2022 sebesar 988.68 l/dtk sedangkan Kendari, 2016
tahun 2027 sebesar 1008,43 l/dtk sehingga dapat
mencukupi seluruh kebutuhan air bersih masyarakat Triatmodja, R., WaterNet 1.1, Nafiri,
prioritas Kota Kendari (6 kecamatan) , namun belum Yogyakarta
dapat memenuhi untuk kebutuhan air bersih seluruh
Kota Kendari. Triatmodjo, B, 1995, Hidrolika I, Beta
2. Hasil analisis dan simulasi hidrolis jaringan perpipaan Offset, Yogyakarta.
adanya jaringan distribusi air bersih berjalan lancar dan
Triatmodjo, B, 1996, Hidrolika II, Beta
tidak lancar. Dengan adanya perbedan tekanan di tiap
Offset, Yogyakarta.
junction. Tekanan menurun disebabkan karena adanya
perbedaan elevasi pada lokasi tersebut. Tingginya tekanan Walsky, T. M, 1996, Analysis of Water Distribution
juga dipengaruhi oleh diameter pipa. Terdapat beberapa System, Van Nostrand Reinhold, Melbourne,
node yang tidak memenuhi standar tekanan. Semua node Australia.
yang letaknya berjarak dekat dengan pompa/booster akan
memiliki tekanan yang besar dikarenakan besarnya head
pada pompa distribusi yang terpasang.
Dengan semakin menjauhi sumber air maka tekanan akan
semakin kecil.
4.2 Saran
Abstract— Ever since the Internet has been presented in mission to be the most hospitable company in the world,
this planet, labor markets have expanded its coverage over the had to spend 42 days to hire people in one term of
world, which has made the hiring process in a company’s recruitment. This situation could slower Hilton to obtain
human resources more and more challenging. However, their company mission.
Artificial Intelligence (AI) has taken up an important role to
The hiring process sometimes also generate added cost
accelerate the process of finding potential employees in
multinational company. Our research contribution is to for the company when the process could not meet the timing
examine how AI upgrades the hiring process and people target since it will relate to the sales number in several cases
management within companies, and what exactly might be the in automotive companies. For instance, according to Perez
obstacles to collaborating with the AI technology. In addition, (2017), Sonic Automotive that is one of the largest
we would like to introduce AI technologies, which assists the automotive retailers in the country with more than 100
hiring process in the company. They are Fama and HireVue. locally branded dealerships nationwide, had experienced to
Fama is a platform that helps the HR division in their hiring sales vacancies cost their dealerships an average of 500
process by conducting web searches on a candidate and USD per day in lost sales. It was a big number in daily cost
scanning their public social media for negative or positive
that can reduce the total of company profit.
attributes. Meanwhile, HireVue analyzes candidates’ facial
expressions and speech from interviews, and then provides On the other aspect of discomfort in hiring process is the
clients with feedback of the candidates’ many qualities. Based talent lived in the different region even country thus hiring
on secondary data, both these AI technologies have been team most of the time had to travel to conduct the interview. It
proved that have a number of significant benefits for hiring generated not only transportation costs, such as, airplane or
process as well as have some positive and negative perspective train ticket, but also it costed the time to do that kind of activity.
on organizational behavior. This condition happened, for instance, Atlanta Public School,
Index Terms— Artificial Intelligence, Human Resource, which has to find A+ teacher for their students in several
Hiring Process, Video Intelligence, Social Media Screening, regions to meet and interview them. Sometimes it became
HireVue, Fama. worsen when they did not find teacher who fits with their
requirements after doing the long trip. Based on Hall (2017),
Atlanta Public School had an inconvenient experience both for
I. INTRODUCTION candidate and hiring team at the same time for doing some
interviews and it costed much money for travel and time.
To support a business process in the era of industry 4.0, Therefore, in education business, they also argue that
having a fit candidate to achieve the company’s goal is a traditional method in the interview was not efficient to find
prerequisite. Industry 4.0 has required a talent who is agile out their talents.
to adopt with dynamic business environment. Its Furthermore, HR team also consumed a lot of hard
phenomenon challenges the company particularly in the times to read, recognized and categorized their applicants’
recruitment. Moreover, since last decade, human capital has Curriculum Vitae (CV) since they are favorite company for
been tremendously diverse due to some reasons. One of the labor, consequently, they very often to received more
reasons is emerging of hiring platforms that cause people than 150 applicants within one week. Taking Cathay Pacific
are able to apply a job not only for vacancy in their countries as an example, According to Tsang (2018), Their HR team
but also in many countries. However, many Human consistently receives more than 300 applicants within a
Resource (HR) managers in multinational companies from week. Most of applicants were chasing a job as a customer
various business industries have tackled those complexities service or a flight attendant. Consequently, as HR team,
of hiring process through Artificial Intelligence (AI) as their they had to do some very manual screening stages which
solutions. were CV screening for the large number of applicants, did
Previously, hiring as one of job descriptions of HR a phone call (phone screen), conducted group interview
department took so much time to find the right person for step, then, a final interview in person with their end user or
each specific job. They frequently try to select the person potential manager. From that process, the hard time came in
for both doing the job its self and adopting the company between candidate who had successful in phone screening
culture. According to Gathright (2017), Hilton who has a step they did show up into group interview session.
However, even though they had spent their time to find the
best talents for every position they had, the method was not
efficient even costly. H1: HireVue could boost the performance of hiring
Hiring process was even more demanding for fast– process in those companies through developed AI
fashion industry to have a right employee who can adopt technologies.
their dynamic-culture business. On this business, the
employee has to have not only a desire to work hard but also Ensuring the characteristic or behavior of applicants
need to be more creative to follow its trend. However, during hiring process is also vital in order to recognize their
although some company have developed digital ability to adopt the workplace culture. It is similar from the
recruitment, they still face a struggling period to do the previous research of Zhao et al. (2018) that mentioned a
hiring process. To illustrate it, according to Korellis (2018), positive relation between culture and innovation output.
Urban Outfitters has developed the digital process for their However, it would be difficult to observe it with one
hiring process since they moved from paper applications interview even find it in a group discussion. Nevertheless,
into online application. They used applicant-tracking Fama came out with the brilliant AI idea to solve the
system but they realized that they had not founded out the uncertainty of working behavior from applicant through
solution to recognized their best candidates or understand social media.
who they really need. Moreover, this situation came when From fama official website, we can see data regarding
their employees interacted directly with the customers. 70% of employers use social media and online search
Therefore, they needed to found their emotions and engines to screen candidates before hiring, up significantly
personalities. A profile or a resume can show some from 60% last year and 11% in 2006. Moreover, more than
experience but it does not tell how that person will respond half of employers (54%) have found content on social media
to a customer or present themselves on a sales floor. Those or during an online search that caused them to fire or not to
intangible qualities that are most critical to our operations hire an individual. Therefore, Fama would be an effective
that could not be captured effectively through that system. method to find out the
The other report came from the leader of potential employee’ attitude in workplace before we
telecommunication in the US. It was Vodafone. According send them a working contract.
to Ross (2017), They stated the traditional method of their In addition to that, fama has some innovations to help
hiring process does not fit to complete their need in finding hiring process. Fama accounts has ability to configure in
their employee, especially for retail position. On that order to highlight only the behaviors or culture in your
method, they had to do typical applications and phone organization deems relevant to a hiring decision. Moreover,
screenings where it was not able to see the companies are allowed to pull in resume data from their
how the candidates will be interacting with the ATS or use Fama’s cloud-hosted web app. Fama will then
customers. Whereas, they believe that position is the conduct a comprehensive social, news and web search and
representative of their company’s name in front of customer identify relevant publicly available information.
and it is important to be able to gauge their excitement and After elaboration all of the above, thus we
behavior. In addition to that, it also had taken too much time hypothesize
and too many potential talents before making a hire. In
average, it took at least 23 days. It was too long for the H2: Fama could escalate the performance of hiring
telecommunication company as big as Vodafone. process in those companies through developed AI
Those kind of complaints regarding hiring process technologies.
could be solved by AI solution for HireVue. HireVue assists
global enterprises experience a competitive advantage in the
modern talent marketplace through video interviewing II. LITERATURES REVIEW
software and assessments. Hiring Intelligence on this
platform is transforming the way companies discover, hire, This paper illustrates many comparisons points to
and develop talent. By mixing video interviews with define the impact of Artificial Intelligence on many
predictive, validated I-O science and artificial intelligence, industries. Most of them are described in the numbers of
HireVue augments human decision-making in the hiring percentage. Therefore, we provide some calculation to find
process and provides higher quality talent, faster. out those rating to ensure the effect of each variable that
Nowadays, HireVue works with over 700 customers this paper mentions.
globally, including leading brands such as Vodafone, Intel,
Tiffany & Co., Honeywell, Qantas, Carnival Cruise Line,
and 40% of Fortune’s Most Admired. They help their NPS (Net Promoter Score)
clients lead their industries with 50% faster growth, 29%
less turnover and 13% more top performers. HireVue had We find out to obtain the value of NPS in hiring process
experienced to be top 10 “Most Promising Companies” in through this formula that developed by Reichheld (2003):
America by Forbes and is a five-time winner of “Top HR
Product of the Year” by HR Executive Magazine. NPS = % Promoters - % detractors
The biggest challenge for business in this century is [1] Gathright M. 2017. Hilton Cuts Time to Hire Nearly 90% with
finding the best labor that fit with the company’s culture. It is Hirevue Assessment.
[2] Hall P. 2017. Atlanta Public School Hires A+ Teachers with
important because the human capital is the answer of
Hirevue.
competitive advantage for each company. However, it has been [3] Korellis M. 2018. Urban Outfitters Makes Hourly Hiring Hip with
more and more challenging after internet and the openness of Digital Recruiting Across 200 Stores.
labor influence the process of hiring. They bring so many [4] Perez J. 2017. Sonic Automotive Trades in Outdated Hiring
options to decide then it increase the level of uncertainty. Methods.
Nevertheless, AI has been proven in order to boost the [5] Pike JC, Bateman PJ, Butler BS. 2018. Information from social
performance of hiring process to tackle those obstacles. networking sites: Context collapse and ambiguity in the hiring
Offering video intelligence, HireVue has evolved the process. Information Systems Journal 28:729-758.
[6] Reichheld FFJHbr. 2003. The one number you need to grow.
process of hiring for various industries. First, this platform
81:46-55.
had a good feedback in reducing the time of hiring then it [7] Ross A. 2017. Vodafone Halves the Time to Build Retail Teams
made HR team can continue to other job descriptions. It also with Hirevue.
made some cost saving for the company particularly for [8] Tsang Q. 2018. Cathay Pasific Improves Hiring Time Over 90%
travel cost to visit the applicant’ regions. The possibility of with Video Interviewing.
applicant who would like to attend the interview after doing [9] Zhao H, Teng H, Wu QJCJoAR. 2018. The effect of corporate
culture on firm performance: Evidence from China. 11:1-19.
HireVue process was going up that proves it can read the
1
Abstract—Landslide is a geological hazard that leads fatalities [7-9]. Therefore, it is important to provide a good quality of
each year in Indonesia. Many efforts are done to reduce and landslide inventory. Indonesia itself already has Landslide
prevent the landslide occurrence in Indonesia, including build the Inventory Data Base of Indonesia (LIDIA) as landslide
landslide susceptibility map. In building this map, we need to
inventory data [10, 11]. However, it still could not easily access
collect both causative factors in an area and the landslide
inventory database. However, Indonesia is still lack of the by public community, including landslide researchers. Depart
landslide inventory data, either in amount of landslide occurrence from this gap, this paper would like to show the importance of
or in the time range. By taking Cianjur as case study area, this landslide inventory in building the landslide susceptibility map.
research aims to show the importance of landslide inventory in
building the landslide susceptibility map. Landslide inventory
Cianjur, West Java, Indonesia is chosen as research area for
database was collected from the open source data of BNBP from study case because it has high occurrences of landslide every
2011-2018. The landslide susceptibility map was analyzed using year [12]. Cianjur also well known as an area which form by
Frequency Ratio (FR) model. The result of the calculation shows high geological activity, especially Southern Cianjur [13]. They
values of susceptibility are between 0-612.08. The area is classified are the reasons why Cianjur County is chosen as study area.
into five zones of landslide susceptibility level with success rate of
the prediction analysis equal to 83.33%. It concludes that the II. METHOD
inventory database plays an important role in classification
process. The amount of the landslide inventory database still a far A. Landslide Inventory
from the standard. Our challenge is to build higher quality of Landslide inventory of the research area is plotted based on
landslide inventory database in this era of big data and industrial the data from Indonesian National Board for Disaster
revolution 4.0. Management-INBDM (2012-2015) and Indonesian Geological
Index Terms—big data, classification, landslide, random Agency-IGA (2011-2018). It collected 91 landslide points in the
forest, susceptibility map research area. 75% of the landslide inventory are used as training
dataset while the rest of the data are used as testing data for the
I. INTRODUCTION validation of the model.
Indonesia is an area with unique geological condition. It is
the meeting point of three tectonic plates namely Eurasian Fig. 1 shows the distribution of the landslide occurrences in
Plate, Pacific Plate, and Indo-Australian Plate. It has made the study area.
Indonesia become rich of both geological resources and
hazards. It forces all of stakeholders in this country to be B. Causative Factors
adaptive toward this geological condition [1-3]. Causative factors are several features that control the
susceptibility of landslide in an area. These controlling factors
Landslide is one of the geological hazards that still become mainly dominated by the nature of the area. It is represented by
source of fatality in many areas in Indonesia. Landslide in the geomorphological, geological, and hydrogeological
Indonesia mainly occur due to earthquake and rainfall as condition of the area [14, 15]. The selection of the causative
triggering factors. Several landslide susceptibility models, factors could be important to be considered. It is because, by
using statistical method, are already built as an effort to prevent selecting an ineffective factor, it could reduce the robustness of
and predict the landslide occurrences in several area [4-6]. the model, although theoretically it will affect the landslide
In building the landslide susceptibility map, the first step susceptibility [16, 17].
that should be conducted is building the landslide inventory. It This study used three causative factors, comprising slope,
will be used as both the training and validation data. The longer aspect, he elevation. These three causative factors represent the
time of inventory data, the better the quality of the inventory geomorphological conditions of the area. This study is still
2
going on by considering the geological and hydrogeological facing the sun will have higher water content [18, 19]. The area
aspects. The slope of the area divided into 10 classes and it is divided into 10 aspect classes based on the geographical
could be seen in Fig. 2 Based on this map, the area with slope direction.
>34̊is about 18% from total area. Fig. 4 shows the zone of elevation of the area. It is divided
into 10 classes from 3 m to 2996 m. More than 40% of the
research area has elevation more than 1000m.
D. Frequency Ratio
Frequency ratio (FR) is a bivariate statistical method that Table 1.
will be used for building the landslide susceptibility model. Frequency Ratio (FR) Calculated in the Research Area for 3
It will establish the relationship between the landslide Causative Factors
inventory and the causative factors [24, 25]. The FR judge Factor FR
the significance of each class in each causative factor toward
the landslide occurrence. The formula of this concept will be Slope Angle (o)
like this: 0.00-4.19 0
_ 4.19-8.14 0
b _ 8.14-11.84 1.2393
= = __ (1) 11.84-15.79 1.1141
_ _
15.79-19.98 1.2073
The value of the FR in each factor will be influenced by
19.98-24.42 1.2470
the number of the classes in each factor and the threshold
between each class. FR near to 1 means it is not significance 24.42-29.11 1.2702
toward the landslide while FR>1 means the classes having 29.11-34.54 1.2654
importance influence toward the landslide [24, 25]. 34.54-41.69 1.3146
The FR will be used for making the Landslide 41.69-62.90 1.3510
Susceptibility Index (LSI) for each cell in research area. LSI
is the sum of the FR of all input parameters in each cell. It Aspect (o)
will be mathematically stated as: Flat (-1) 0
=∑ (2) North (0-22.5) 0
With FRi is the frequency ratio for i-th class of each factor Northeast (22.5-67.5) 1.5451
considered [25]. East (67.5-112.5) 1.3422
Southeast (112.5-157.5) 1.1078
III. RESULTS AND DISCUSSION
South (157.5-202.5) 1.1577
A. Study Area
Southwest (202.5-247.5) 0
The study area is in Cianjur County, West java Province,
Indonesia. The total area 3840 km2. From the geological West (247.5-292.5) 1.4315
data, the area is composed mainly by Tertiary sedimentary Northwest (292.5-337.5) 1.4402
rocks such as sandstone and claystone also Quaternary North (337.5-360) 0
Volcanoes Deposition like breccia and tuff [26]. Error!
Reference source not found. shows the Digital Evaluation Elevation (m)
Model (DEM) image and the landslide distribution in 3.00-179.06 0
research area.
179.06-378.59 0
378.59-566.39 1.6654
B. Frequency Ratio Results 566.39-754.18 1.6603
The calculation of the Frequency Ratio method has 754.18-941.98 1.6739
produced the indexes of FR for each causative factor that is
shown in Table 1. The causative factors that influence the 941.98-1129.77 1.6785
landslide susceptibility in the research area are slope angle, 1129.77-1341.04 1.6801
elevation, and slope aspect. For the slope angle, aspect, and
1341.04-1611.00 0
elevation there are 8 classes (8.140-62.900), 7 classes, and 6
classes that have positive correlation toward the landslide 1611.00-2103.97 0
occurrence, respectively. 2103.97-2996.00 1.6831
For the slope angle, the correlation increasing gradually as C. Landslide Susceptibility Model
the raising of the gradient of the slope. For the slope aspect, The landslide susceptibility was done by two model. Model-1
the positive correlations are shown in the slope facing to the only consider the nature factor of the area (geomorphology
Northeast-Southeast and Wes-Northwest direction. It might aspect) and model-2 is considering the landslide inventory
be caused by the covering effect of vegetation on the other database that already collected from IGA and INBDM website.
direction or the equal portion of sunshine in equator region. For the model-1 the landslide susceptibly was built by summing
Elevation factor give a positive correlation starting from the reclassified causative factors in GIS system directly. It was
378.59 masl to 1341 masl and also 2103.97-2966 masl. It is done by giving the same weight for each causative factor.
usually also related in steepness of the slope at those
elevation level.
4
IV. CONCLUSION
Fig. 6 shows the result of the susceptibility map built The study area was analyzed the susceptibly of landslide
without calculate the landslide inventory. It is shown that the using two model, i.e. by considering and not considering the
model predict area with high susceptibility of landslide by landslide inventory database. From the analysis it could be
(more) red color. It is looked like that the susceptibility map learned that by considering the landslide occurrences database,
success in predict several prone areas. However, it is also we could improve our susceptibility map. We could also do a
present that several locations, where landslides happen, are verification and validation so that it could measure the success
misclassified as less susceptible of landslide.
and prediction rate of the model.
As mentioned before, model-2 considered the landslide
history that represented by its inventory database for 7 years. Therefore, it is important for having a high-quality landslide
The model was developed using Frequency Ratio, a bivariate inventory database to produce a high-quality landslide
statistical approach. Each class of each causative factors were susceptibility. By the time, good quality of landslide database
reclassified based on weight that derived from FR calculation could also be improved starting from point database then move
(Table 1). The landslide susceptibility map then be generated forward to build an area database (polygon data). It requires a
as the collective value of Landslide Susceptibility Index based team work among many stakeholders, such as geological survey
on Eq. 2 using GIS software. The result of the calculation agency, universities, and any other institutions related to
shows values of susceptibility are between 0-612.08. landslide spatial consideration.
Fig. 7 shows the result of the susceptibility map using
model-2 which classify the study area into five classes of
susceptibility. It shows different appearance compared with the
result of model-1. Moreover, it can be identified that the prone
area is more compatible with the landslide distribution. The
success rate of the prediction is represented by the area under
curve (AUC) analysis equal to 83.33 (Fig. 8). The prediction
rate using 25% inventory data resulted AUC equal to 63.63%
(Fig. 9). The low value of AUC for prediction rate could be
influenced by the number of causative factors. It should also
consider the other causative factor that, theoretically,
influenced the landslide occurrences, e.g.: lithology, distance
from faults, distance from river, river flow accumulation, etc.
5
V. REFERENCES
the meaning and activities of creative tourism, it is not limited service evaluation of post-consumption that involves an
to culture. In case of cultural tour, visitors are only given an assessment comparing what consumers receive and what
explanation of local culture by the guide, in creative tourism consumers need from a product. Therefore, perceived value
visitors learn many things actively and hunt various assessment is subjective [27], each consumer has different
experiences from their environment to evolve their potency necessity that causing various assessment according to their
[20]. Therefore, the concept of creative tourism has expanded perceptions.
to various activities involving tourists [16]. In a recent study, Shen [17] has elaborated a specific
In creative tourism tourists are given an occasion to develop measurement scale to evaluate perceived value in creative
their potency through active participation in various learning tourism context. The mensuration scale extends to have 6
experiences [19]. Tourists are also invited to engage in dimensions, consisting of: functional value: benefits obtained
creative experiences by generating a unique creation using from the performance of a product or service; social value: the
simple materials and their imagination, like creating ability of a service to improve personal image; emotional
traditional handicrafts, cooking, painting porcelain, drawing or value: the capability of a product or service to result emotional
making sculpture [21]. Furthermore, tourist destinations in feelings or changes; perceived sacrifice: consumer sacrifice to
developed countries are increasingly developing their creative get a service; experiential value: the prowess of an excursion
tourism concept. There are Creative Paris which offers to make someone forget his problems; epistemic value: the
creative tour about technology and science, also fashion and perceived benefits of a service to arouse curiosity.
design; crative tourism in Taiwan that teaches about natural
ecology; and creative tours in Barecelona that provide
D. Satisfaction
workshops related to performing arts [20]. Essentially,
whatever the form, in creative tourism vistor are invited to Experts interpret satisfaction variously. However, the most
participate actively and get authentic experiences [7] so they commonly used are Engel and Oliver's disconfirmation theory
are drive to actualize themselves [16]. which compares perceptions and expectations [28]. According
to Oliver in Chen and Chen [15], satisfaction refers to
conformity between expectations and performance perceived
B. Experience Quality by consumers after consuming a product or service. Similarly,
The concept of experience quality is often juxtaposed with Kotler [29] stated satisafaction as feeling happy or
service quality [15]. In service quality, services measurement disappointed as a result the process of comparing performance
is related to performance of each attribute, while experience with expectations. Moreover, satisfaction is a comprehensive
quality refers to psychological assessment yielding from assesment of organizational performance in relation to meet
tourist participation in tourism activities [15]. Hence, customer needs [30]. If performance or experience is
involvement of psychological factors in the form of emotions perceived to be less than consumer expectations, customers
and feelings expand the scope of experience quality [22]. feel dissatisfied; if according to expectations, satisfaction will
Besides, in experience concept, the experience tourist feel as be felt; as if exceeding expectations, customers feel delighted
consumers does not only occur when consuming service, but [29].
also when communicating and interacting with service
providers [23]. E. Behavioral Intention
Various dimensions to assess experience quality have been
Intention is a subjective possibility of an individual to
developed. Pine and Gilmore in Ali [19] introduced 4E
perform certain behaviors [16]. Hence, the concept of
measurement scales (education, escapism, esthetics, and
intention refers to behavioral theory. When tourists have an
entertainment) in evaluating experience in the accommodation
intention to revisit same destination, it can be a prediction
industry. In tourism context, Xu and Chan’s research on
their behavior in the future [16]. For tourism businesses,
tourists visiting China uses four dimensions, namely:
understanding and predicting tourist behavior in the future are
recognition and escape, peace of mind and relaxation,
important. Tourists who have a positive intention indicates an
involvement, and hedonics [24]. These researchers use
attitude of loyalty, where this loyalty is a determining factor in
different dimensions, but have a relatively similar
the sustainability of a company [15]. Those who feel a positive
understanding and take tourist participation as the main factor.
behavioral intention also tend to inform positive word of
mouth or recommend their experience to others and revisit
C. Perceived Value even though they must pay more [31].
Zeithaml in Chen [15] defines perceived value as consumer
perception in assessing the overall benefits that consumers
receive from a product, where the benefits are compared to the III. METHODOLOGY
costs incurred and sacrifices made by consumers. In this case, The data were obtained from 167 local tourist in four
Zeithaml describes value in four meanings: (1) low prices, (2) creative tourism destination in Bandung through convenient
what consumers want from a product, (3) quality obtained distribution of self-administrated questionnaire. Most of
from prices paid by customers, and (4 ) what is obtained from destination engaged visitors to involve in sundanese culture,
what consumer has given [25]. Not too different from like participating in traditional games, drawing batik, playing
Zeithaml, Yuan in Kim [26] defines perceived value as an
3
music assembly and crafting puppet. Some of them also upon outer loading and AVE (Average Variance Extracted)
participated in sports attraction; archery and horse riding. value. In pursuance of Anderson and Gerbing [32] the
Existing literature with some improvisation and a 5-point construct meet validity criteria if value of each indicators
likert scale (strongly agree-strongly disagree) was applied for exceed 0,5 [32]. Table 2 confirms both of outers loading and
construct measurement. The validity and reliability using AVE having adequate value, above 0,5. For the validity
confirmatory factor analysis were conducted. In terms of data assessment, this research prefer to apply composite reliability,
analysis, this research utilized descriptive analysis and partial which has standard of 0,7. Thus, as depicted from table 2, the
least square SEM. The first analysis was to find out tourist requisite of reliability is fulfilled [33].
perception, while the second was to test hypothesis.
TABEL II
VALIDITY AND RELIABILITY MEASUREMENT
IV. RESULTS
A. Descriptive Analysis Outers
Variabel CR AVE
Loading
Generally, tourist give a positive assessment for creative Experience Quality 0.853 0.545
tourism. As depicted from table 1, mean value for experience Escape 0,515
quality reach 4,113. Indicating tourist get a quality excursion Peace Of Mind 0,715
and optimal experience, a circumstances when people feel Involvement 0,896
involved in attractive and fun activity [30]. The same, Learning 0,841
Recognition 0,661
perceived value has fairly high mean value. Sacrifice of time,
Perceived Value 0.873 0.632
cost, and energy spending by tourist commensurate with Functional Value 0,780
facilities, happiness, and benefits gained. However, further Social Value 0,830
analysis reveal social value take lower value possession than Emotional Value 0,818
other dimensions of perceived value. This lower assessment Perceived Sacrifice 0,749
come from “My personal image is increase” statement. Satisfaction 0.806 0.676
Analysis from this fact provide conclusion that experience of Satisfaction A 0,893
Satisfaction B 0,745
creative tourism is feasible to share to relatives and friend, but
Behaviour Intention 0.804 0.677
it doesn’t make them feel proud and icrease their image. Behaviour Intention A 0,927
Behaviour Intention B 0,704
TABEL I
DESCRIPTIVE ANALYSIS
Variabel Mean Std. Deviation C. Structural Analysis
Experience Quality
Escape 4,093 0,587
To verify the proposed hypothesis and structural model,
Peace Of Mind 4,296 0,503 this research utilize SmartPLS V.3. Bootstrapping procedure
Involvement 4,086 0,485 with 500 iterance is employed to evaluate the signification of
Learning 4,207 0,522 weight indicators and path coefficient [34]. Specifically,
Recognition 3,883 0,588 hypothesis testing considers to three item, namely p value,
Mean 4,113 0,537 original sample, and t-statistic.
Perceived Value
Functional value 4,057 0,561
TABEL III
Social value 3,949 0,572
HYPOTHESIS TESTING
Emotional value 4,141 0,578
Perceived sacrifice 4,207 0,541
Path Coefficient
Mean 4,088 0,563
Hypothesis Original T P Conclusion
Satisfaction 4,449 0,575 Sample Statistics Values
Behaviour Intention 4,377 0,612 H1: Experience Quality →
0.193 1.970 0.049 Accepted
Behavioral Intention
Compared to other variables, satisfaction has the highest H2: Perceived Value →
mean value. Evincing a very high level of satisfaction that 0.147 1.382 0.167 Rejected
Behavioral Intention
achieve affective delight condition, a situation where
H3: Experience Quality →
perceived performance exceeds consumer expectations [28]. 0.392 4.277 0.000 Accepted
Related to behavior intention, the mean value is 4,377, Satisfaction
expressing positive behavior intention that lead to loyal H4: Perceived Value →
0.213 2.108 0.035 Accepted
attitudes, which will determine the sustainability of a company Satisfaction
in the future [15]. From both of high mean values, it can be H5: Satisfaction →
0.482 6.101 0.000 Accepted
concluded that tourist expectations for pleasant tour can be Behavioral Intention
achieved. Also, they are agree to revisit current destination
and do word of mouth to their relatives.
The output of hypothesis testing in table 3 shows hypothesis
2 having p-value <0,05 and t-statistic <1,96, which doesn’t
B. Measurement Analysis meet the required standard [35]. While, others hypothesis
In evaluating construct accuracy, this study conducted result satisfying value with positive original sample.
validity and reliability test. Validity test was assessed built Hypothesis 1 and 3 concern in impact of experience quality to
behavioral intention and satisfaction is accepted. This fact
support previous research [16, 36] but also refute antecedent
4
studies [15, 19, 21]. Experience quality have positive and satisfied then he has a tendency to buy back. Likewise in
direct effect on both of variables without being mediated by tourism services, this study and foregoing researchs [15, 19]
another variable. These finding indicate that various confirm that a tourist who is pleased with an excursion incline
experiences are presented in creative tourism attraction are to have an intention to revisit the destination.
able to provide psychological and social benefits as tourist The detail information regarding to influence of each
expected. The result, tourists not only satisfy but also dimension is presented by figure 1. In first independent
reflexively encourage them to come back. variable, the most influential dimension is involvement,
The effect of perceived value variable explain by hypothesis having highest coefficient (0,799). Involvement or entrant
2 and 4. Table 3 point out that hypothesis 2 is rejected, the participation in creative activity is a prevalent element in
second independent variable has no impact to behavioral tourism that incriminate creativity [7]. Because, the main
intention. That is, consumer perception of comparison purpose of tourists can be obtained if tourists are involved and
between benefit and sacrifice they spend only affect actively participate in organized attractions [8]. Therefore, the
satisfaction without a direct desire to revisit. Last, hypothesis quality of a tourist's experience in creative tourism is greatly
testing between satisfaction and behavioral intention. As influenced by their involvement in the followed attractions.
supposed by researcher, hypothesis 5 is accepted. This finding The more they are involved, the more quality of experience
supports theory stated by Oliver [37], when someone feels they feel.
Abstract— Jaring Interkoneksi Mahakam merupakan utilitas Hasil peramalan dapat memiliki persentase galat (error
listrik di Kalimantan Timur yang diharapkan andal dengan percentage) yang rendah sehingga sistem operator dapat
ketersediaan cadangan listrik 155,46 MW. Dengan tambahan mengobservasi kondisi sistem dengan kondisi yang mendekati
interkoneksi dengan Sistem Barito Kalimantan Selatan, kondisi real-time.
kapasitas terpasang sistem Mahakam bertambah 92 MW.
Namun, dilaporkan tiga kali pada 18 Februari 2018, 5 April 2018 II. DASAR TEORI
dan 11 Agustus 2018, pemadaman listrik besar terjadi di
sebagian besar kota di Kalimantan Timur seperti Samarinda, A. T-test dan coefficient correlation analysis [1]
Bontang, Balikpapan dan Kutai Kartanegara karena alasan T-test dan coefficient correlation analysis dilakukan untuk
teknis. Untuk mengatasi masalah ini, perencanaan yang tepat memilih atribut informasi cuaca dan kondisi yang signifikan
dan strategi operasi perlu dilakukan, dengan mengamati kondisi
masa depan menggunakan peramalan beban jangka pendek,
dengan peramalan yang akan dilakukan. Melalui kedua tes
menengah dan panjang. Beberapa atribut seperti pola beban tersebut, nilai dari p-value dan R akan dihitung untuk
historis dan data cuaca digunakan untuk melakukan peramalan mengetahui kuat relasi antar variabel input dan output.
beban sehingga keseimbangan daya yang tepat dapat dilakukan Semakin tinggi nilai R maka semakin kuat relasi variabel
oleh operator sistem. Selain itu, prediksi infrastruktur yang tersebut terhadap output yang diramal. Sebaliknya, semakin
berlebihan juga dapat dilakukan untuk menghindari overheating kecil nilai p-value maka semakin kuat relasinya dengan output
yang parah yang dapat memicu pemadaman besar. Dengan yang diramal. Untuk nilai p-value, nilai yang dianggap
melakukan peramalan beban dengan atribut terkait, signifikan sebaiknya kurang dari 5% significance level
perencanaan yang tepat dan strategi operasi dapat dilakukan walaupun dalam aplikasi, batas significance level tersebut
tanpa mengorbankan kenyamanan pelanggan listrik.
dapat disesuaikan dengan kebutuhan riset.
Index Terms—load forecasting, load modelling, supervised
learning B. Artificial Neural Network (ANN) [2]
ANN atau disebut dengan jaringan saraf tiruan adalah sebuah
I. PENDAHULUAN metode peramalan supervised learning yang terdiri dari
beberapa lapisan (layer) yang memiliki input, hidden dan
Pemadaman bergilir yang terjadi sebagai akibat permasalahan output layer. Secara umum, ANN bekerja dengan asumsi
teknis dalam pengoperasian Jaring Interkoneksi Mahakam blackbox dimana model dibangun berdasarkan susunan layer
dapat ditanggulangi dengan perencanaan dan strategi operasi tersebut melalui input dan output yang diketahui pada saat
yang tepat. Dengan ketersediaan cadangan listrik sebesar pelatihan (training). setiap jaringan tiruan ini terdiri dari
155.46 MW dan tambahan interkoneksi dengan Sistem Barito neuron yang bekerja sama untuk membangun model prediksi.
Kalimantan Selatan sebesar 95 MW, utilitas listrik di Pendekatan model untuk menghasilkan prediksi output yang
Kalimantan Timur diharapkan menjadi andal tanpa tepat dilakukan melalui proses training yang berulang.
pemadaman bergilir. Namun pada kenyataannya, dilaporkan Back Propagation Neural Network bekerja melalui
terdapat tiga kejadian pemadaman luar biasa secara bersamaan mekanisme perhitungan perbedaan antara input dan output
di mayoritas kota besar di Kalimantan Timur yaitu Kota atau galat E yang dideskripsikan pada persamaan berikut:
Samarinda, Bontang, Balikpapan dan Kutai Kartanegara pada
18 Februari 2018, 5 April 2018 dan 11 Agustus 2018 yang
disebabkan oleh kesalahan teknis. Salah satu cara untuk
mencegah terjadinya permasalahan yang sama adalah melalui
peramalan baik pada beban (load) dan sumber daya energi (1)
baru terbarukan (EBT) (renewable energy resource).
Salah satu metode untuk melakukan peramalan beban dan (2)
sumber daya EBT adalah melalui jaring saraf tiruan (artificial
neural network) dan regresi linear (multiple linear regression).
(3)
Dalam penggunaan kedua metode ini, pengkondisian data
sebelum digunakan pada model peramalan akan dilakukan (4)
melaui t-test dan coefficient correlation. Melalui tes statistik
ini, hanya attribute yang memiliki relasi kuat yang akan
digunakan untuk menyusun masukan model peramalan. (5)
Tujuan dari penelitian ini adalah untuk membangun model
peramalan yng akurat untuk beban dan sumber daya EBT.
2
(9)
Actt dan Fort adalah nilai aktual dan hasil prediksi. Actt-1
adalah nilai aktual periode sebelumnya. Mean Bounded
Relative Error didapat dengan,
(10)
III. METODE
A. Data Set
Data yang digunakan untuk penelitian ini adalah data historis
cuaca, beban dan EBT tenaga matahari. Data historis cuaca
diambil dari penyedia data cuaca open source [5]. Data
historis beban didapat dari sistem jaring tenaga listrik ISO-
New England, Massachusets USA yang tersedia secara open
source melalui [6] sedangkan untuk panel surya Green
Campus Shalun NCKU, Taiwan. Seluruh data set merupakan
data time series yang diambil melaui Application
Programming Infrastructure (API) dan Automatic Meter
Infrastructure (AMI) tiap satuan jam. Gambar 2. Diagram Alir Konstruksi Model Peramalan Daya Tenaga
Surya
3
Abstract—Setelah tahap tanggap darurat dan pemulihan bahwa diduga kuat telah terjadi longsor bawah laut yang
maka rekonstruksi menjadi tahap berikutnya yang harus menjadi penggerak awal gelombang tsunami. Di tengah tanda
dilaksanakan di wilayah Teluk Palu dan sekitarnya yang telah tanya para ahli yang belum terjawab, penanganan bencana
diguncang gempa dan dilanda tsunami. Pembangunan kembali harus dilakukan untuk menjamin kelangsungan hidup warga
sarana dan prasarana yang rusak akibat tsunami memerlukan
perancangan yang tepat agar diperoleh hasil optimum dan dapat
terdampak yang akan lebih cepat bangkit jika ada
diandalkan (reliabel). Di sisi lain, perencanaan wilayah dengan kebersamaan semua pihak [11].
mempertimbangkan upaya mitigasi secara mendalam menjadi Fase tanggap darurat ditetapkan oleh pemerintah selama
hal yang mutlak dilakukan pula. Dua pendekatan dalam dua minggu sejak 28 September 2018 dan kemudian
perencanaan dan perancangan untuk rekonstruksi pasca gempa diperpanjang selama dua minggu berikutnya hingga 26
dan tsunami di Sulawesi Tengah, yaitu deterministik dan Oktober 2018. Fase ini difokuskan untuk pencarian,
probabilistik didiskusikan pada tulisan ini. Bagi para pengambil penyelamatan, dan evakuasi para korban. Tahap selanjutnya
kebijakan dapat memandang secara luas wilayah yang harus adalah pemulihan yang ditujukan untuk menyediakan fasilitas
dilakukan rekonstruksi dengan mempertimbangkan berbagai
dasar agar kehidupan dapat berjalan menuju normal. Tahap
probabilitas yang mungkin akan dialami di masa datang,
terutama menyangkut kemungkinan terjadinya gempa dan rekonstruksi segera menyusul dan perencanaannya telah
tsunami. Di pihak lain, para insinyur perencana menggunakan didiskusikan oleh pihak berwenang mengikuti tahapan dalam
cara deterministik dalam desainnya sembari melengkapi dengan undang-undang [15].
aspek probabilistik agar diperoleh struktur bangunan sesuai Artikel ini bertujuan untuk memberikan saran dan
kriteria desain. Kedua metode memiliki peran masing-masing pendapat tentang penggunaan metode deterministik dan
dalam analisis risiko dan potensi bencana. Saling melengkapi probabilistik dalam mendukung tahap rekonstruksi yang akan
satu sama lain untuk mendapatkan pandangan tambahan dilaksanakan. Rekonstruksi di sini hanya dibatasi pada
terhadap kegiatan mitigasi bencana. Kapan salah satu metode pengertian pembangunan kembali fasilitas fisik yang musnah
lebih diprioritaskan bergantung kepada lingkup wilayah dan
atau rusak akibat gempa dan tsunami. Sedangkan rekonstruksi
jenis fasilitas yang akan dibangun kembali.
Index Terms— bencana, deterministik, gempa, mitigasi, sosial dan ekonomi tidak didiskusikan dalam artikel ini. Para
probabilistik, rekonstruksi, tsunami. insinyur perencana dan pelaksana, pengambil kebijakan
mitigasi bencana, serta para pemangku kepentingan ada
I. PENDAHULUAN baiknya memberikan perhatian terhadap kedua pendekatan
Jumat, 28 September pukul 18:02:44 waktu lokal, di saat tersebut untuk diterapkan secara tepat. Saran dan pendapat
sebagian besar orang tengah bersiap melaksanakan sholat dalam pembahasan ini bersifat umum dan kualitatif, yang
maghrib, Teluk Palu diguncang gempa kuat dengan perlu dirinci dan dikuantifikasi lebih lanjut.
magnitude 7.4. Episentrum terletak pada koordinat 119.85° Pendekatan secara deterministik dan probabilistik telah
BT dan 0.18° LU dengan kedalaman 10 km di Timur Laut menjadi diskusi yang memunculkan banyak pendapat dari
Kota Donggala. Meskipun episentrum berada di wilayah batas para ahli. Dalam bidang kegempaan, deterministik telah lebih
luar Teluk Palu, kerusakan paling parah justru diderita Kota dulu banyak diaplikasikan dalam perencanaan struktur
Palu yang berada di ujung teluk dan berjarak tak kurang bangunan hingga sebuah metode lain diperkenalkan oleh [3],
dari 70 km dari episentrum. Dua fenomena besar mengikuti yaitu probabilistik, yang kemudian populer dengan sebutan
kejadian gempa tersebut yaitu liquifaksi dan tsunami. Probabilistic Seismic Hazard Analysis (PSHA). Seolah terjadi
Bencana yang terjadi di sebagian wilayah Sulawesi “persaingan” dalam penggunaan kedua metode tersebut
Tengah ini telah mengherankan para ahli dan peneliti gempa seperti didiskusikan oleh [4], [7] dan [13]. Sedangkan [5]
dan tsunami dari berbagai belahan dunia. Secara geologis, secara logis mengkritisi metode probabilistik untuk gempa
wilayah terjadinya gempa berada pada sesar atau patahan dengan alasan adanya ketidaksesuaian antara peta rawan
Palu-Koro, salah satu patahan aktif di Indonesia yang bertipe gempa dengan kejadian kerusakan gempa pada daerah yang
patahan mendatar (strike-slip). Tipe patahan ini bergerak dinyatakan berisiko rendah terhadap gempa.
secara horisontal satu sama lain sehingga sebenarnya tidak
menimbulkan deformasi vertikal yang signifikan untuk
memicu lahirnya tsunami. Namun fakta di Sulawesi Tengah
telah terjadi dimana tsunami telah meluluhlantakkan berbagai
objek dan fasilitas serta memakan korban yang tidak sedikit.
Sampai 21 Oktober 2018, sebanyak 2.113 korban dilaporkan
meninggal dalam tragedi ini. Spekulasi muncul, salah satunya
2
II. PEMANFAATAN TELUK PALU Kejadian gempa dan tsunami telah menyebabkan kerusakan
Teluk Palu menjadi bagian sangat vital bagi Provinsi pada fasilitas yang digambarkan oleh Gbr. 1 dan ditampilkan
Sulawesi Tengah. Pergerakan orang dan barang terjadi pada Tabel 1 pada berbagi tingkatan mulai dari ringan hingga
intensif di daerah ini. Teluk Palu turut memberi andil dalam berat.
pertumbuhan ekonomi Sulawesi Tengah dimana pada periode
2010-2017 pertumbuhan ekonomi tertinggi dicapai pada tahun III. TIPE KERUSAKAN BANGUNAN
2015 yang mencapai dua digit yaitu 15,52 %. Selanjutnya Sebuah tim yang merupakan kerjasama antara Department
pada tahun 2016 mencapai 9,98% dan merupakan of Hydraulic and Ocean Engineering, National Cheng Kung
pertumbuhan ekonomi provinsi tertinggi di Indonesia. Tahun University dengan Jurusan Teknik Sipil Universitas Jenderal
berikutnya turun menjadi 7,14% namun masih di atas Soedirman telah melakukan survei pasca gempa dan tsunami
pertumbuhan ekonomi nasional 5.07% [2]. di Teluk Palu dan sekitarnya. Salah satu hasil survei adalah
Gbr. 1 dan Tabel 1 menggambarkan pemanfaatan Teluk mengenai tipe kerusakan bangunan. Terdapat tiga tipe
Palu untuk berbagai kepentingan. Berdasarkan survei oleh kerusakan bangunan yang dapat diamati yaitu kerusakan
penulis, setidaknya ada 17 lokasi yang terdapat bangunan dan akibat gempa, likuifaksi dan tsunami.
fasilitas untuk menunjang kehidupan masyarakat.
A. Kerusakan akibat gempa
Kerusakan akibat gempa umumnya bercirikan struktur
roboh pada arah horisontal. Tiang atau kolom miring dan
dinding roboh. Objek-objek bergeser ke arah mendatar.
Deformasi struktur ke arah vertikal tidak dominan. Peristiwa
17 fenomenal adalah ambruknya Jembatan Palu IV atau
16 Jembatan Kuning yang merupakan ikon Kota Palu. Jembatan
ini berada di muara Sungai Palu. Saksi mata dan bukti-bukti
1
menunjukkan bahwa jembatan roboh disebabkan oleh gempa
15 bukan oleh tsunami.
14
2
13
3
4 12
11
5 10
9
6 78
Gbr. 1. Pemanfaatan Teluk Palu, jenis fasilitas pada setiap nomor ditampilkan
pada Tabel 1
TABEL 1
FASILITAS PENTING DI TELUK PALU
1,5 m
(c)
(c) Gbr. 3. Contoh kerusakan akibat likuifaksi di Kota Palu, berturut-turut adalah
Gbr. 2. Contoh kerusakan akibat gempa di Kota Palu, berturut-turut adalah (a) (a) rumah tenggelam di Petobo, (b) rumah tertimbun lumpur di Petobo, dan
Jembatan Palu IV (jembatan kuning), (b) Hotel Roa-roa, dan (c) pagar SMK (c) perumahan menjadi tak berbentuk di Balaroa
Sigi bergeser sejauh 1,5 meter.
(b)
(
a
)
(
a
)
4