Академический Документы
Профессиональный Документы
Культура Документы
Confidential Document…
Project:
Stage:
Date : 2012-11-15
Prepare by : 黄晓波
Check by : 曾吉祥
Approval by : 程文华
Yes
No
NA
2. Adapter structure
2-1 Bulk-cap彎腳需成直角
2-2 Bulk-cap防爆孔需有至少keep 1mm air gap
2-3 功率元件keep gap 5mm with Bulk-cap or E-cap
2-4 所有Component彼此本體不得直接觸碰(Gap至少0.2mm)
2-5 浮高元件&磁性元件需點膠固定
2-6 PCB板邊至少 keep 1mm gap
2-7 Length of Pin cut is under 3.5mm 是否平行
2-8 直立式元件Pin腳裸露under 1mm
2-9 超音波線structure review(開殼後檢視超音波膠是否對稱分布)
2-10 高壓元件需與heat-sink絕緣隔離
3. DC output
3-1 DC cable SR 注料孔不可在彎折點
3-2 DC Cable 需標註耐溫等級,線號,安歸編號
3-3 Check DC plug type 非圓筒式
980910 REV.01
Form writer by Shoy Lin
PK10000FK60
NB-65B19 BSMI 2007-3-27 2013-3-26
KC 2007-3-12 N/A
Approved By
COMPAL ASIAN POWER DEVICES INC.
仁寶電腦 亞源科技股份有限公司
APD
2012-11-17
DCC
何艷梅
亞 源 科 技 股 份 有 限 公 司
APD
ASIAN POWER DEVICES INC.
ADD:NO.5 LANE 83. LUNG-SOU ST, TAO-YUAN CITY, TAIWAN R.O.C.
TEL:886-3-379-9078 FAX:886-3-379-9263
Rev. 00
亞 源 科 技 股 份 有 限 公 司 ASIAN POWER DEVICES INC.
APD
Change List Model No. : NB-65B19-CAZ
Rev. Date Changed contents Why Prepared by Checked by Approved by
Customer 仁寶電腦
Customer P/N 后補
陳聰 何艷梅
The Contents
Model No. NB-65B19-CAY Rev. 00
Input:90-265V,47~63Hz;
Description Output:19V/3.42A Date 2012-11-17
Customer 仁寶電腦
Customer P/N 后補
陳聰 何艷梅
Electrical Specification
1. SCOPE
This specification describes the physical, functional and electrical characteristics of the 65 watts, single output
+19V/3.42A, switching power supply.
2. INPUT CHARACTERISTICS
2.7. Efficiency
Output current 3.42A/2.56A/1.71A/0.85A; input voltage 115/230Vrms, sum of each efficiency division 4
should be greater than 87%.
3. OUTPUT CHARACTERISTICS
3.1. Output Characteristics
Output voltage, load current, voltage regulation and output noise of power supply should meet the
specifications, which defined on the tables below:
Line Regulation ±1 %
Note 1: Ripple voltage measurement is done with an oscilloscope set at a 20M Hz bandwidth & output wire 100
mm terminated with 0.1uf ceramic capacitor & parallel with 47uf Low ESR electrolytic capacitor at full
load.
Adapter
DC Output
DC Cable
Note 2:
Turn On/ /Hold up Time
+19V
90% 95%
95%
DC Output 10%
0V
3.2.2. Over Voltage Protection : Power supply shall be latch off, before output voltage reached 29V.
And the power supply shall not recover automatically unless the AC
reset. Test condition: 230Vac/0.5A load.
3.2.3. Over Current Protection : Power supply shall be prohibited output before output current reached
6A.
3.3. Overshoot :
Output overshoot during power-on and power-off shall not exceed 20V.
4. ENVIRONMENT SECTION
4.1. Operating Temperature : 0°C to 40°C
5. RELIABILITY
5.1. MTBF : 130K hr minimum at 25°C, and 230Vac input voltage /full load 3.42A.
5.2. Vibration
5.2.1. Non-Operating : Acceleration 3.5G / Frequency 10~500Hz/ Vibration duration 60 minutes/
Force Direction at X, Y, Z
6. SAFETY SECTION
TUV-INMETR
Brazil IEC 60950-1
O (I.T.E.)
7. EMC SECTION :
8. ENVIRONMENT STANDARD :
8.1. ROHS Directive 2002/95/EC
8.2. WEEE Directive 2002/96/EC(Article 4 &6&10)
9. MECHANICAL SECTION
9.1. Dimension : Refer to mechanical drawing for the details.
A A
85.5 +- 0.2 C2
070294-11
Model No.
INPUT ( )( ) : 100-240V 1.6A 50-60Hz
33.5 +- 0.2
KOUZIRO
OUTPUT( ! )( ! ) :19V 3.42A
"9+:;<2000m=>?@ABC*+
3*
Vendor LOGO R
1.
5
S/N LABEL 60*6mm
C C
APD Proprietary Information/Document: No publicity ,transmission to third party or competitor is allowed without APD Prior written consent.
APPROVED DATE 2012-11-09
CHECKED DATE 2012-11-09
Dimensions ≤6 >6-30 >30-80 >80-180 >180-320 >320-600 >600 DESIGN DATE 2012-11-09
A ±0.05 ±0.1 ±0.15 ±0.2 ±0.25 ±0.35 ±0.5 DESCRIPTION
Tolerances v B
±0.1 ±0.15 ±0.2 ±0.25 ±0.4 ±0.5 ±0.65 NB-65B19-CAZ
LABEL ASSEMBLE
unless
C ±0.2 ±0.3 ±0.4 ±0.6 ±0.8 ±1 ±2 PART NO.
otherwise ORD.
D ±0.5 ±1 ±1.5 ±2.2 ±0.35 ±5 ±6.5 TYPE NO. REV. CODE
mentioned
Holes: ±0.1 Angles: ±0.5 L8030-61080 00 A
SIZE A4 UNIT mm SCALE 2:1 THIRD ANGLE PROJECTION SHEET1OF1
OP-04-300-12 REV1.6
REV. ORD. REVISION NOTE. DATE DESIGN APPROVED
A A
*85.5 +- 0.2 C2
070294-11
Model No.
*33.5 +- 0.2
Made in China
! ( "#!) F3
3*
R
1.
Vendor LOGO 5
60 . 5x7mm
S / N label,
C
C
NOTES:
1. MATERIAL: MYLAR( POLYESTER FILM #100)+Matt PET.
ADHESIVE: K.K. NO.9 OR EQUIVALEENT.
2. COLOR: Background:Black; WORD:White.
3. LABEL MUST BE DIE CUT PROPERLY AS PER DIMENSION.
4. LABEL MUST BE UL RECOGNIZED AND CSA CERTIFIED.
D 5. THE LABEL IS SUPPOSED TO BE PASTED ON PC CASE EVENLY AND PROPERLY. D
IT'S NOT ALLOWED TO HAVE ANY BULGE HAPPEEN ON THE LABEL AFTER BE
BURNT IN 48 HRS IN OVEN WHICH TEMPERATURE IS 85℃.
6. FACTORY CODE DATA IS PROVIDED BY PRODUCTION CONTROL SECTION.
7. Must meet RoHS requirement and APD environmental standard (APD Document No.ISO-10-702)
8. Halogen free Compliance
8.1 Test method:
Acceptable test methods are EN14582 or IEC 61189-2:2006 or US EPA
SW-846 Method 5050 or EN 50267-2-1:1999. (EN14582 is preferred)
8.2 Restricted substances & maximum concentration values:
Total
Substance Chlorine(Cl) Bromine(Br) concentration
of Cl + Br
Permissible Limit
(by weight)(PPM) 900 900 1500
APD Proprietary Information/Document: No publicity ,transmission to third party or competitor is allowed without APD Prior written consent.
APPROVED DATE 2012-11-09
CHECKED DATE 2012-11-09
Dimensions ≤6 >6-30 >30-80 >80-180 >180-320 >320-600 >600 DESIGN DATE 2012-11-09
A ±0.05 ±0.1 ±0.15 ±0.2 ±0.25 ±0.35 ±0.5 DESCRIPTION
Tolerances v B ±0.5 ±0.65 NB-65B19-CAZ
SAFETY LABEL
±0.1 ±0.15 ±0.2 ±0.25 ±0.4
unless
C ±0.2 ±0.3 ±0.4 ±0.6 ±0.8 ±1 ±2 PART NO.
otherwise ORD.
D ±0.5 ±1 ±1.5 ±2.2 ±0.35 ±5 ±6.5 TYPE NO. REV. CODE
mentioned
Holes: ±0.1 Angles: ±0.5 612-12613 00 A
SIZE A4 UNIT mm SCALE 2:1 THIRD ANGLE PROJECTION SHEET1OF1
OP-04-300-12 REV1.6
1 2 3 4
D D
FS1 DB3 Ck1 Ck2 Ca1 T1A C1 Co1 Co2 C2
1 LF1 LF2 3
L B1 +Vout
F1
T3.15A L 250V Ra1
RX1 CX1 DB1 Do1
RX2
RX3 Ra2 JP1
TR1 DB2 GND
2 5
N F2
AC1 DB4
Ra3
Da1
3
G
Da1*
Dh1 Rp1
C 1 C
Rh1 Ch1 Da1*
T1B
RX4 Rp2
2
Rv1 Rf1 Rf2 Rf3
J1 Rp3
Cf1
8
1
Dg1 PC1A
Rv2 U1
ZD1 Q1
8
Rg1 Rf8
7 5 U2
TR2
LD7575 Rg2 Rf9
Qv1 1 1
2
3 Cds1 Rf5 Rf4
Rt1 Rf10 TSM103
LD8103 Rf12
7
Rv7 Rs2
Rv4
Df1
4
B B
Dv1
Rg3 Cf2 Cf5
4
Rs1 J2
4
Rf6 Rf7
Dv2 Cf3
Cf4 PC1B
Qv2
Rv5 Rv6 Rv3 Rf11
Cv1
3
CY1
Main Board
1 RS2 RES CF 1/8W 1K J TAP AI 1 pc TZAI YUAN
2 J2 RES CHIP TF 1/10W 0 J (0603)(AI) 1 pc TA-I
(2) J2 RES CHIP TF 1/10W 0 J (0603)(AI) 0 pc YAGEO
(2) J2 RES CHIP TF 1/10W 0 J (0603)(AI) 0 pc TZAI YUAN
3 RA1 R C. TF 1/8W 62K J 0805 1 pc TA-I
(3) RA1 R C. TF 1/8W 62K J 0805 0 pc YAGEO
(3) RA1 R C. TF 1/8W 62K J 0805 0 pc WALSIN
4 RA2 R C. TF 1/8W 62K J 0805 1 pc TA-I
(4) RA2 R C. TF 1/8W 62K J 0805 0 pc YAGEO
(4) RA2 R C. TF 1/8W 62K J 0805 0 pc WALSIN
5 RA3 R C. TF 1/8W 62K J 0805 1 pc TA-I
(5) RA3 R C. TF 1/8W 62K J 0805 0 pc YAGEO
(5) RA3 R C. TF 1/8W 62K J 0805 0 pc WALSIN
6 RX1 R C. TF 1/8W 910K J 0805 1 pc TA-I
(6) RX1 R C. TF 1/8W 910K J 0805 0 pc YAGEO
(6) RX1 R C. TF 1/8W 910K J 0805 0 pc WALSIN
7 RX2 R C. TF 1/8W 910K J 0805 1 pc TA-I
(7) RX2 R C. TF 1/8W 910K J 0805 0 pc YAGEO
(7) RX2 R C. TF 1/8W 910K J 0805 0 pc WALSIN
PS: It indicates second source when quantity is "0" or item no. includes "( )".
APD Proprietary Information / Document : No publicity , transmission to third party or competitor is allowed without APD
Prior written consent.1/11
OP-04-317-02 REV:1.1
Item No. Designation/Content Specification Description Quantity Unit Supplier
PS: It indicates second source when quantity is "0" or item no. includes "( )".
APD Proprietary Information / Document : No publicity , transmission to third party or competitor is allowed without APD
Prior written consent.2/11
OP-04-317-02 REV:1.1
Item No. Designation/Content Specification Description Quantity Unit Supplier
PS: It indicates second source when quantity is "0" or item no. includes "( )".
APD Proprietary Information / Document : No publicity , transmission to third party or competitor is allowed without APD
Prior written consent.3/11
OP-04-317-02 REV:1.1
Item No. Designation/Content Specification Description Quantity Unit Supplier
PS: It indicates second source when quantity is "0" or item no. includes "( )".
APD Proprietary Information / Document : No publicity , transmission to third party or competitor is allowed without APD
Prior written consent.4/11
OP-04-317-02 REV:1.1
Item No. Designation/Content Specification Description Quantity Unit Supplier
PS: It indicates second source when quantity is "0" or item no. includes "( )".
APD Proprietary Information / Document : No publicity , transmission to third party or competitor is allowed without APD
Prior written consent.5/11
OP-04-317-02 REV:1.1
Item No. Designation/Content Specification Description Quantity Unit Supplier
PS: It indicates second source when quantity is "0" or item no. includes "( )".
APD Proprietary Information / Document : No publicity , transmission to third party or competitor is allowed without APD
Prior written consent.6/11
OP-04-317-02 REV:1.1
Item No. Designation/Content Specification Description Quantity Unit Supplier
PS: It indicates second source when quantity is "0" or item no. includes "( )".
APD Proprietary Information / Document : No publicity , transmission to third party or competitor is allowed without APD
Prior written consent.7/11
OP-04-317-02 REV:1.1
Item No. Designation/Content Specification Description Quantity Unit Supplier
PS: It indicates second source when quantity is "0" or item no. includes "( )".
APD Proprietary Information / Document : No publicity , transmission to third party or competitor is allowed without APD
Prior written consent.8/11
OP-04-317-02 REV:1.1
Item No. Designation/Content Specification Description Quantity Unit Supplier
PS: It indicates second source when quantity is "0" or item no. includes "( )".
APD Proprietary Information / Document : No publicity , transmission to third party or competitor is allowed without APD
Prior written consent.9/11
OP-04-317-02 REV:1.1
Item No. Designation/Content Specification Description Quantity Unit Supplier
PS: It indicates second source when quantity is "0" or item no. includes "( )".
APD Proprietary Information / Document : No publicity , transmission to third party or competitor is allowed without APD
Prior written consent.10/11
OP-04-317-02 REV:1.1
Item No. Designation/Content Specification Description Quantity Unit Supplier
PS: It indicates second source when quantity is "0" or item no. includes "( )".
APD Proprietary Information / Document : No publicity , transmission to third party or competitor is allowed without APD
Prior written consent.11/11
OP-04-317-02 REV:1.1
ZERTIFIKAT
CERTIFICATE
GS-1106-176730-000
Seite / Page 1 / 2
Gültigkeit Expiry Date 28.02.2013 Dieses Zertifikat ersetzt das Zertifikat GS-0908-132999-001
vom 25.08.2009. Neue Fertigungsstätte hinzugefügt.
This Certificate replaces the Certificate GS-0908-132999-001
dated 2009-08-25. New factory added..
Genehmigungsinhaber Asian Power Devices Inc. Der Inhaber der Genehmigung ist berechtigt
das Nemko GS-Zeichen auf dem hier
Licence Holder No. 5, Lane 83, Lung-Sou Street
beschriebenen Produkt für die Gültigkeitsdauer
Taoyuan City des Zertifikats anzubringen.
Taiwan Weitere Hinweise siehe unten.
The holder of this certificate is entitled to use
the Nemko GS-mark on the product described
Fertigungsstätte Siehe Seite 2 / See page 2 below. The Nemko GS-mark is only to be used
Manufacturing Plant within the validity of this certificate.
For further notice, see below.
Geprüft nach EN 60950-1:2006 + A11:2009; DIN EN ISO 12100-2:2004 + A1:2009 teilweise /
Tested according to partially; PAK Anforderungen / PAH Requirements ZEK 01.2-08
Zertifiziertes Produkt AC Schaltnetzteil / AC Adapter
Certified Product
Bezeichnung NB-65B19….
Type Designation
1,6 A, 100 – 240 V AC, 50-60 Hz, Klasse I.
DC-Ausgang: 3,42 A, 19 V
Zusätzliche Informationen siehe Seite 2.
Handelsname:
Trade mark:
Test Report Nr.: Main report 132999 vom / dated 2009-08-18
Test Report No.: Amendment 176730 vom / dated 2011-05-25
Das Baumuster entspricht den zum Zeitpunkt der Ausstellung dieser Bescheinigung geltenden sicherheitstechnischen Anforderungen
gemä §4 und §7 GPSG. Dem Zertifikat liegen die Geschäftsbedingungen und die Prüf- und Zertifizierungsordnung der Prüfstelle zugrunde.
Das Produkt entspricht den oben genannten Anforderungen, die Herstellung wird überwacht (§7 Abs.2 GPSG).
Der Hersteller hält die Voraussetzungen ein, die für eine vorschriftsmäßige Fertigung erforderlich sind und duldet die damit verbundenen
Kontrollmaßnahmen zur Überwachung der Fertigung (§7 Abs.3 GPSG).
Bei Nichteinhaltung der Vorschriften kann die Zeichengenehmigung zurückgezogen werden (§7 Abs. 2 GPSG).
The tested model described above complied with the safety requirements according to §4 and §7 in the GPSG at the time of certification.
This certificate is issued based on the regulations of the certification body.
In accordance to the rules of GS certification, production surveillance is performed (§7, Ch. 2 GPSG). The manufacturer must meet the
requirements for production, and accept any control measures related to production surveillance (§7, Ch. 3 GPSG).
In case of any irregularities or non-compliances, this certificate can be withdrawn with immediate effect (§7, Ch. 2 GPSG).
Ausstellungsdatum: 20.06.2011
Date of Issue
signature
Hans Fibich
Zertifizierungsstelle
Certification Department
NB-65B19….:
Die Punkte in der Modellbezeichnung stehen für “0-9”, „a-z“, „A-Z“, „-“ oder kein Zeichen und dienen
Marketingzwecken.
The dots in the model name can be “0-9”, „a-z“, „A-Z“, “-“ or blank, for marketing use only.
Ausstellungsdatum: 20.06.2011
Date of Issue
signature
Hans Fibich
Zertifizierungsstelle
Certification Department
Product: AC ADAPTER
Model No.: NB-65B19XXXX( “X” can be “-“,”0” to “9”, “A” to “Z” or “ blank”)
Manufactured at:
F1: Yang Ming Industrial
Bao An Maliu Village, Heng Gang Town, Long Gang District, Shen Zhen 518115, P. R. China
Representative in the EU
Manufacturer :
Asian Power Devices Inc.
No. 5, Lane 83, Lung-Sou St., Taoyuan
City 330, Taiwan
Shenzhen, 18 January, 2010 Thales Yang / Section Manager
(Place and date of issue) (Name and signature of authorized person)
Representative in the EU:
EMISSION
Standard Item Result Remarks
Conducted (Main Port) PASS Meet Class B limit
V-2 2006.04/V-3 2006.04
Radiated PASS Meet Class B limit
Note: 1. The test result judgment is decided by the limit of measurement standard.
2. The information of measurement uncertainty is available upon the customer’s request.
The above equipment has been tested by Compliance Certification Services Inc., and found compliance
with the requirements set forth in the technical standards mentioned above. The results of testing in this
report apply only to the product/system, which was tested. Other similar equipment will not necessarily
produce the same results due to production tolerance and measurement uncertainties.
Page 4
This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.
Issue Date: 2009-12-01 Page 1 of 2 Report Reference # E168210-A36-UL-2
Product Category: Power Supplies for Information Technology Equipment Including Electrical
Business Equipment
Product Category CCN: QQGQ, QQGQ7
Test Procedure: Listing
Product: AC Adapter
Model/Type Reference: NB-65B19XXXX (Where X can be any alphanumeric character or blank) (XXXX
only for client and marketing usage)
Rating(s): I/P: 100-240 Vac, 50-60 Hz, 1.6 A;
Copyright © 2009
Issue Date: 2009-12-01 Page 2 of 2 Report Reference # E168210-A36-UL-2
This is to certify that representative samples of the products covered by this Test Report have been investigated in accordance with the
above referenced Standards. The products have been found to comply with the requirements covering the category and the products are
judged to be eligible for Follow -Up Service under the indicated Test Procedure. The manufacturer is authorized to use the UL Mark on
such products which comply with this Test Report and any other applicable requirements of Underwriters Laboratories Inc. ('UL') in
accordance with the Follow -Up Service Agreement. Only those products which properly bear the UL Mark are considered as being
covered by UL's Follow -Up Service under the indicated Test Procedure.
The applicant is authorized to reproduce the referenced Test Report provided it is reproduced in its entirety.
Any information and documentation provided to you involving UL Mark services are provided on behalf of Underwriters Laboratories
Inc(ULI) or any authorized license of ULI.
Copyright © 2009
DECLARATION OF CONFORMITY
Product AC ADAPTER
Model NB-65B19xxxx (“x” can be “-”, “0” to “9”, “A” to “Z” or blank)
Trade Name APD
Applicant Asian Power Devices Inc.
No.5, Lane 83, Ling-Sou st., Taoyuan City, TaiWan
Manufacturer(s) Asian Power Devices Inc.
No.5, Lane 83, Ling-Sou st., Taoyuan City, TaiWan
Applicable Standard(s) FCC Part 15 Subpart B Class B (DoC)
Measurement Procedure ANSI C63.4: 2003
Report No. SZ070822B10-EF
Test Laboratory Compliance Certification Services (Shenzhen) Inc.
No. 5, Jinao industrial park, No.35 Jukeng Road, Dashuikeng Village, Guanlan
Town, Baoan District, Shenzhen, China
Tel: +86-755-28055000/ Fax: +86-755-28055221
This device has been tested and found to comply with the stated standard(s), which is(are) required
by the Federal Communications Committee. The test results are indicated in the test report and are
applicable only to the tested sample identified in the report.
14 February 2007
Ady Tsai
Asian Power Devices Inc.
This letter authorises Asian Power Devices Inc., to label the product(s) listed
below, with the C-Tick compliance mark as shown above and supplier
number N136, subject to the following conditions:
a. The units supplied are identical to those held by and described in the
compliance folder held by Qualsure Consultants.
b. Qualsure Consultants assumes no responsibility in the retail supply,
servicing or repair of the listed product.
c. Any modification to the listed product(s) voids this authorisation.
d. This authorisation pertains only to the product(s) listed.
e. The product(s) listed, where necessary, hold and maintain an Australian
electrical safety certificate.
f. Asian Power Devices Inc. takes responsibility and agrees to meet all
costs in any action relating from a breach of the conditions of this
authorisation.
g. Asian Power Devices Inc. agrees to supply to Qualsure Consultants the
names and addresses of all Australian importers if required by the
relevant Australian authority.
The labelling and supply of the product with a C-Tick compliance label
including the identifier N136 is agreement with the above conditions.
Gordon Slimmon.
Director
Gordon Slimmon
Dear Sir / Madam,
Enclosed is the Certificate(s) in respect to your recent application received by Energy Safe Victoria.
Please take time to check the certificate to ensure that all details are correct in accordance with your application,
and that you understand all of the conditions imposed on the approval.
Should you have any queries, please contact Naveen Kapoor on telephone 92039774,or email
nkapoor@esv.vic.gov.au
Any samples that accompanied your application are available for collection, and if not collected within 20 business
days of the date hereon may be disposed of.
Notification must be given to Energy Safe Victoria of any change of registered Address within 20 business days.
Yours faithfully
Energy Safe Victoria Level 3, Building 2, 4 Riverside Quay, Southbank 3006 Telephone (03) 9203 9700
ABN 27 462 247 657 PO Box 262, Collins Street West, Victoria 8007 Facsimile (03) 9686 2197
Certificate Number: ESV120084/00
Certificate of Approval
This is to certify that the Director of Energy Safety has approved the electrical equipment described hereunder.
Any modifications to the electrical equipment or its place of manufacture must be approved by Energy
Safe Victoria prior to the equipment being supplied or offered for supply.
Notification must be given to Energy Safe Victoria of any change to the name or address of the holder of
the certificate within 20 business days.
ARTICLE DETAILS
Electrical Equipment: Prescribed
Power Supply or Charger
Power Supply
Relevant Standards: AS/NZS 60950-1:2011
Expiry Date: 15/03/2017
Conditions of Approval: Alternate approval marking V07191
Approval details
Model NB-65B19. . . .
Rated at Input: 100-240 V, 1.6 A, 50-60 Hz AC
Output: 19 V, 3.42 A, DC
Trade Name APD
Comments Suffix '.' denotes 0 to 9 , A to Z, "-" or
blank for marketing use
Customer: NA
Stage: DVT
Rev.: 1.0
ISO-10-600-11 Rev1.0
Page 2
1. General information:
This documentation describes the power adapter design validation test plan of the NB-65B19 including test
requirements, test equipment list and test result. In the report, aall test input and output condition is followed Appendix,
but every test item is followed E-Specification. All test item conditions are in the followed report.
2. Appendix
Test condition:
1. Input condition:
90 47
100 60
115 60
230 50
240 50
265 63
2. Output condition:
ISO-10-600-11 Rev1.0
Electric Function Test Report
1.1 Input character test Page 4
Model No.: NB-65B19 Sample S/N: 01, 02 Test By: Jafly
Sample Rev.: 1.0 Check By: zhouwanxia
AC Power EUT
Input Output DC Load
Source Analyzer
Test item Input Output load Specification Sample 01 Sample 02 Judge Remark
CONCLUSION : OK NG
ISO-10-600-11 Rev1.0
Electric Function Test Report
1.3 Output character Test Page 5
Model No.: NB-65B19 Sample S/N:01, 02 Test By: Jafly
Sample Rev.: 1.0 Check By: zhouwanxia
1.3.1 Test Requirement:
This test is to verify whether the power adapter’s output character meets the requirement of E-specification,
the output character contains the following items:Output Tolerance,Ripple Voltage,Hold up time,Turn on time Dynamic etc.
When the test result meet the specification,the test item is passed.
1.3.2 Test equipment and block diagram:
Test equenments list:
Chroma Programmable AC Source 6530;Chroma Smart Electric Load 63010;Tektronix Digital Phosphor Oscilloscope 3012B
EUT
AC Input Output
Source DC Load
Oscilloscope
ISO-10-600-11 Rev1.0
Electric Function Test Report
1.3 Output character Test Page 7
Note 1: Ripple voltage measurement is done with an oscilloscope set at a 20M Hz bandwidth & output wire 100
mmterminated with 0.1uf ceramic capacitor & parallel with 47uf aluminum capacitor at full load.
Note 2:
Input 90~265Vac
Rise time
90%
( 18.05Vdc)
+19V Output
10%
Note 3:
Test Condition:
Output change between 0%~100% of full load.
Slew rate 1A/us
Frequency 100Hz
50% duty cycle.
CONCLUSION : OK NG
ISO-10-600-11
ISO-10-600-11Rev1.0
Rev1.0
Electric Function Test Report
1.2 Energy Star evaluation test Page 7
Model No.: NB-65B19 Sample S/N: 01, 02 Test By: Jafly
Sample Rev.: 1.0 Check By: zhouwanxia
1.2.1 Test Requirement:
This test is to verify whether the power adapter meets the requirement of EPA ENERGY STAR®Level Ⅳ standard,
the Energy Star evaluation test contains the following items:Power Consumption,Efficiency..
When the test result meet the specification,the test item is passed.
1.2.2 Test equipment and block diagram:
Test equenments list:
Chroma Programmable AC Source 6530;Chroma Smart Electric Load 63010;Universal Power Analyzer PM3000A.
AC Power EUT
Input Output DC Load
Source Analyzer
CONCLUSION : OK NG
ISO-10-600-11 Rev1.0
Electric Function Test Report
1.4 Protection character test Page 8
Model No.: NB-65B19 Sample S/N: 01, 02 Test By: Jafly
Sample Rev.: 1.0 Check By: zhouwanxia
1.4.1 Test Requirement:
This test is to verify whether the power adapter’s protection character meets the requirement of E-specification,
the Protection character contains the following items:Short Current Protection,Over Voltage Protection,Over Current Protection etc.
When the test result meet the specification,the test item is passed.
1.4.2 Test equipment and block diagram:
Test equenments list:
Chroma Programmable AC Source 6530;Chroma Smart Electric Load 63010;Universal Power Analyzer PM3000A.
AC EUT
Input Output DC Load
Source
Temperature&
Humidity chamber Oscilloscope
Test item Input Output load Specification Sample 03 Sample 04 Judge Remark
90Vac/47Hz short NO damage OK OK PASS Pin=0.22
S.C.P
265Vac/63Hz short NO damage OK OK PASS Pin=3.05
O.V.P 230Vac/50Hz 19Vdc/0.5A 26V Max. 22.1V 21.9V PASS Note 1
90Vac/47Hz 19Vdc Io= 5.5A Max 4.775A 4.768A PASS
OCP Note 2
265Vac/63Hz 19Vdc Io= 5.5A Max 4.98A 5.05A PASS
NO deformation
90Vac/47Hz 19Vdc/4.5A and no
PASS
OTP discoloration on
265Vac/63Hz 19Vdc/4.5A case. PASS
Note1: Power supply shall be latch off,before output voltage reached 26V.
And the power supply shall not recover automatically unless the AC reset.
Note2: Power supply will be latched off , But the power supply shall recover automatically when the over current is removed.
CONCLUSION : OK NG
ISO-10-600-11 Rev1.0
Electric Function Test Report
1.5 Phase /Gain Margin Test Page 9
Model No.: NB-65B19 Sample S/N: 01,02 Test By: Jafly
Sample Rev.: 1.0 Check By: zhouwanxia
1.5.1 Test Requirement:
The phase margin should exceed 30 degree at least , and the gain margin should less than -10dB at least.
contains the following items:Phase/Gain Margin test
When the test result meet the specification,the test item is passed.
1.5.2 Test equipment and block diagram:
Test equenments list:
Chroma Programmable AC Source 6530;Chroma Smart Electric Load 63010;Gain&Phase margin Analyzer.
EUT
AC DC Load
Input Output
Source
CONCLUSION : OK NG
ISO-10-600-11 Rev1.0
Safety Test Report
2. Safety test Page 10
Model No.: NB-65B19 Sample S/N: 01, 02 Test By: Jafly
Sample Rev.: 1.0 Check By: zhouwanxia
2.1 Test Requirement:
This test is to verify whether the power adapter’s safety function capable to meet the requirement of IEC60950 standard,
the safety test contains the following items:Hi-pot,Leakage Current, etc.
When the test result meet the specification,the test item is passed.
2.2 Test equipment and block diagram:
Test equipments list:
Chroma Programmable safety tester 9032C
safety EUT
tester
CONCLUSION : OK NG
ISO-10-600-11 Rev1.0
EMS Test Report
3.1 Surge immunity test Page 11
Model No.: NB-65B19 Sample S/N: 10, 11 Test By: liuming
Sample Rev.: 1.0 Check By: zhouwanxia
3.1.1 Test Requirement
This test is to verify whether the power adapter’s Surge immunity to meet the requirement of IEC 61000-4-5 standard,
Condition:
1)Input:220Vac/50Hz Output:19Vdc/3.42A
2)Phase:0,90,180,270 degree Interval:60Sec Times:5
3)Differential mode (Line to Neutral ):±1KV combination waveform impulse
Common mode (Line,Neutral to earth): ±2KV combination waveform impulse
Ambient Temp: 25.8 ℃ Humidity: 52%
Criteria:
A Denotes normal operation,no hardware failure
B Some degradation allowed self recoverable, no hardware failure
C Temporary performance degradation, recovery by operator acceptable, no hardware failure.
When the test result meets the criteria A or B, the power test item is passed.
3.1.2 Test equipment and block diagram:
1) Surge tester: SKS-0510M
2) Chroma Programmable AC Source 6408
3) Chroma Smart Electric Load 63010
4) Concrete Load
Surge EUT
AC Source Tester Input Output Resistance Load
CONCLUSION : OK NG
ISO-10-600-11 Rev1.0
EMS Test Report
3.2:Electrical fast Transient/Burst Test Page 12
Model No.: NB-65B19 Sample S/N: 10, 11 Test By: liuming
Sample Rev.: 1.0 Check By: zhouwanxia
3.2.1 Test Requirement
This test is to verify whether the power adapter’s Surge immunity to meet the requirement of IEC 61000-4-4 standard
Condition:
1)Input:220Vac/50Hz Output:19V/3.42A
2)Pulse Voltage: ±1KV,Burst Duration:15ms
3)Test time :1minute each output(line coupling), Period: 300ms, Frequency: 5kHz, Asynchronous
Ambient Temp: 25.6 ℃ Humidity: 52%
Criteria:
A Denotes normal operation,no hardware failure
B Some degradation allowed self recoverable, no hardware failure
C Temporary performance degradation, recovery by operator acceptable, no hardware failure.
When the test result meets the criteria A or B, the power test item is passed.
Criteria level
Test Mode Test Time Pulse Voltage Judge
Sample 10 Sample 11
L 60S +1KV A A PASS
N 60S +1KV A A PASS
L+N 60S +1KV A A PASS
L+PE 60S +1KV A A PASS
N+PE 60S +1KV A A PASS
L+N+PE 60S +1KV A A PASS
L 60S -1KV A A PASS
N 60S -1KV A A PASS
L+N 60S -1KV A A PASS
L+PE 60S -1KV A A PASS
N+PE 60S -1KV A A PASS
L+N+PE 60S -1KV A A PASS
CONCLUSION : OK NG
ISO-10-600-11 Rev1.0
EMS Test Report
3.3 Electrostatic Discharge Test Page 13
Model No.: NB-65B19 Sample S/N: 10, 11 Test By: liuming
Sample Rev.: 1.0 Check By: zhouwanxia
3.3.1 Test Requirement
This test is to verify whether the power adapter’s Electrostatic Discharge immunity to meet the
requirement of IEC 61000-4-2 standard
Condition:
1)Input:220Vac/50Hz Output:
19Vdc/3.42A
±
2)Air discharge: 15KV Contact discharge: ±8KV
3)Times:900 Interval: 1sec
Ambient Temp: 25.2 ℃ Humidity: 52%
Criteria:
A Denotes normal operation,no hardware failure
B Some degradation allowed self recoverable, no hardware failure
C Temporary performance degradation, recovery by operator acceptable, no hardware failure.
When the test result meets the criteria A or B, the power test item is passed.
3.3.2 Test equipment and block diagram:
1) ESD Tester : N56-1000-2.
2) Chroma Programmable AC Source 6408 EUT Resistance Load
AC Source
Input Output
3) Chroma Smart Electric Load 63010
4) Concrete Load
ESD Tester
10c
10
CONCLUSION : OK NG
ISO-10-600-11 Rev1.0
EMS Test Report
3.4 Voltage DIPS and interruptions Test Page 14
Model No.: NB-65B19 Sample S/N: 10, 11 Test By: liuming
Sample Rev.: 1.0 Check By: zhouwanxia
3.4.1 Test Requirement
This test is to verify whether the power adapter’s Voltage DIPS immunity to meet the requirement of IEC 61000-4-11 standard.
Condition:
1)Input:220Vac/50Hz Output:19V/3.42A
2)Voltage Interruptions: Phase angle: (0∘~315∘, Step 45∘)
Duration(ms): 20ms Repetition: 10 times
3)Voltage Dips: Phase angle: (0∘~315∘, Step 45∘)
、1000ms Repetition: 10 times
Duration(ms): 200ms
Ambient Temp: 25.6℃ Humidity: 52%
Criteria:
A Denotes normal operation,no hardware failure
B Some degradation allowed self recoverable, no hardware failure
C Temporary performance degradation, recovery by operator acceptable, no hardware failure.
When the test result meets the criteria A or B, the power test item is passed.
3.4.2 Test equipment and block diagram:
1) EMC Partner: Transient 2000.
2) Chroma Programmable AC Source 6408
3) Chroma Smart Electric Load 63010
4) Concrete Load
Voltage Dip EUT
AC Source Resistance Load
Tester Input Output
CONCLUSION : OK NG
ISO-10-600-11 Rev1.0
EMI Test Report
3.5 Conduction Test Page 15
Model No: NB-65B19 Sample S/N:03,04 Test By: liuming
Sample Rev: 1.0 Check By: zhouwanxia
2) Output:19Vdc/3.42A
3) For EN55022 standard,class B.
Comduction Emissions
Limit
Frequence(MHz) QP(dBµV) Avg(dBµV)
0.15~0.5 56~66 56~46
0.5~5 56 46
5~30 60 50
When the test result conform to EN55022 standard,class B, the power test item is passed.
3.5.2 Test Equipment an block diagram:
1) Frequency Analyer
2) Chroma Programmable AC Source 6408
3) Concrete Load
AC Test receiver
power
source LISN EUT
ISO-10-600-11 Rev1.0
EMI Test Report
Page 16
Sample 03:110V/60Hz Line Sample 03:110V/60Hz Neutral
ISO-10-600-11 Rev1.0
EMI Test Report
Page 17
Sample 03:230V/50Hz Line Sample 03:230V/50Hz Neutral
CONCLUSION: OK NG
ISO-10-600-11 Rev1.0
EMI Test Report
3.6 Radiation Test Page 18
Model No: NB-65B19 Sample S/N:03,04 Test By: liuming
Sample Rev:
1.0 Check By: zhouwanxia
2) Output:19Vdc/3.42A
3) For EN55022 standard,class B.
Radiation Emissions
Limit
Frequence(MHz) Limit(dBµV)
30~230 30
230~1000 37
When the test result conform to EN55022 standard,class B, the power test item is passed.
3.6.2 Test Equipment an block diagram:
1) Frequency Analyer
2) Chroma Programmable AC Source 6408
3) Concrete Load
Antenna
Test receiver
AC
power EUT
source
ISO-10-600-11 Rev1.0
EMI Test Report
Page 19
ISO-10-600-11 Rev1.0
EMI Test Report
Page 18
CONCLUSION: OK NG
ISO-10-600-11 Rev1.0
Environment Test Report
4.Environment Stress test Page 21
Model No: NB-65B19 Sample S/N:05,06,08,09 Test By: liuming
Sample Rev.:1.0 Check By: zhouwanxia
AC EUT
Input Output DC Load
Source
Temperature &
Humidity chamber
Temp:85℃
High temperature
4.1 Duration:48Hrs 05/06 OK OK
storage
Power off
Temp:-20℃
Low temperature
4.2 Duration:48Hrs 05/06 OK OK
storage
Power off
Temp:40℃
High temperature
4.3 Duration:24Hrs 08/09 OK OK
operation
Power on
Temp:5℃
Low temperature
4.4 Duration:24Hrs 08/09 OK OK
operation
Power on
Temp:40℃
High temperature
R.H:80%
4.5 & High humidity 08/09 OK OK
Duration:24Hrs
operation
Power on
ISO-10-600-11 Rev1.0
Environment Test Report
4.Environment Stress test Page 22
Result
NO. Test item Test condition Sample S/N
Appearance Functional
℃
Temp : +85 / -20 ℃
℃
Dwell 1Hrs at +80 & -20
℃ .
4.6 Thermal cycling Transfer 1Hrs 01 / 02 OK OK
Total 5 cycles
Power off
(Note 1)
85 ℃
25 ℃ 2 3
Hr
1 4 5 6
-20 ℃
1 cycle ---->5cycles
CONCLUSION: OK NG
ISO-10-600-11 Rev1.0
Mechanical Test Report
5.1 Steady Force Test Page 23
Model No.: NB-65B19 Sample S/N:25,26 Test By:: hejunping
Sample Rev.: 1.0 Check By: zhouwanxia
Thrust
Meter 30mm
EUT
TOP
EUT
Result
Item
Sample 25 Sample 26
Mechanical Characteristic OK OK
Hi-pot OK OK
Insulation Resistance OK OK
CONCLUSION: OK NG
ISO-10-600-11 Rev1.0
Mechanical Test Report
5.2 Steel Ball Impact Test Page 24
Model No.: NB-65B19 Sample S/N:25,26 Test By:: hejunping
Sample Rev.: 1.0 Check By: zhouwanxia
5.2.3 Equipment:
1) Steel ball weight: 0.5kg
2) Steel tube height: 130cm
3) Hard board
4) Programmable auto safety tester:9032C
5) Chroma Programmable AC Source 6408
6) Chroma Smart Electric Load 63010
Steel ball
5.2.4 Test way: 50mm
500g
height:130cm
EUT
Result
Item
Sample 25 Sample 26
Mechanic Characteristic OK OK
Hi-pot OK OK
Insulation Resistance OK OK
CONCLUSION: OK NG
ISO-10-600-11 Rev1.0
Mechanical Test Report
5.3 Drop Test Page 25
Model No.: NB-65B19 Sample S/N:25,26 Test By:: hejunping
Sample Rev.: 1.0 Check By: zhouwanxia
EUT
Drop Height
1.0m
Result
Item
Sample 27 Sample 28
Mechanic Characteristic OK OK
Hi-pot OK OK
Insulation Resistance OK OK
CONCLUSION: OK NG
ISO-10-600-11 Rev1.0
Mechanical Test Report
5.4 Stress Relief Test Page 26
Model No.: NB-65B19 Sample S/N:25,26 Test By:: hejunping
Sample Rev.: 1.0 Check By: zhouwanxia
EUT
Input Output
Temperature chamber
Result
Item
Sample 27 Sample 28
Mechanic Characteristic OK OK
Hi-pot OK OK
Insulation Resistance OK OK
CONCLUSION: OK NG
ISO-10-600-11 Rev1.0
Mechanical Test Report
5.5 Strain Relief Test Page 27
DC Output
Line
EUT
Input Output Pull
Meter
Angle: 90º
Result
Item
Sample 27 Sample 28
Mechanic Characteristic OK OK
Hi-pot OK OK
Insulation Resistance OK OK
CONCLUSION: OK NG
ISO-10-600-11 Rev1.0
Mechanical Test Report
5.6 S/R Bending Test Page 28
Model No.: NB-65B19 Sample S/N:25,26 Test By:: hejunping
Sample Rev.: 1.0 Check By: zhouwanxia
Angle: ± 90º
EUT
Input Output Sway Tester
DC Output
Line
Result
Item
Sample 29 Sample 30
Mechanic Characteristic OK OK
Electric Function OK OK
Hi-pot OK OK
Insulation Resistance OK OK
CONCLUSION: OK NG
ISO-10-600-11 Rev1.0
Mechanical Test Report
5.7 Vibration Non-Operating Test Page 29
Model No.: NB-65B19 Sample S/N:25,26 Test By:: hejunping
Sample Rev.: 1.0 Check By: zhouwanxia
EUT
Input Output
Vibration tester
Result
Item
Sample 29 Sample 30
Electric Function OK OK
Mechanical Characteristic OK OK
Hi-pot OK OK
CONCLUSION: OK NG
ISO-10-600-11 Rev1.0
Mechanical Test Report
5.8 Vibration Operating Test Page 30
Model No.: NB-65B19 Sample S/N:25,26 Test By:: hejunping
Sample Rev.: 1.0 Check By: zhouwanxia
AC EUT
Input Output DC Load
Source
Vibration tester
Result
Item
Sample 31 Sample 32
Electric Function OK OK
Mechanical Characteristic OK OK
Hi-pot OK OK
CONCLUSION: OK NG
ISO-10-600-11 Rev1.0
Reliability Test Report
6.1 Thermal Rise Test Page 31
CONCLUSION : OK NG
ISO-10-600-11 Rev1.0
Reliability Test Report
6.2 Component Stress Test Page 32
Temperature chamber
Oscilloscope
CONCLUSION : OK NG
ISO-10-600-11 Rev1.0
Reliability Test Report
location Description Cap. Vmax Temp. Vmax Temp Vmax Temp Vmax Temp
Ck1 C AL120uF 400V M RAD 7.5105 KMG 120uf 400V 105℃ 1.00 0.95 400V 99.8 ℃ 132.0V 98.2 ℃ PASS
Co1 C AL330uF25V M RAD TAP5mm105℃ 330uf 25V 105℃ 1.00 0.95 25V 99.8℃ 19.8V 99.1℃ PASS
Co2 C AL330uF25V M RAD TAP5mm105℃ 330uf 25V 105℃ 1.00 0.95 25V 99.8℃ 19.9V 93.0℃ PASS
CH1 C AL22uF 50V M RAD TAP 22uf 50V 105℃ 1.00 0.95 50V 99.8℃ 22.8V 90.9℃ PASS
Ca1 CAP CHIP CER MULTI. 1nF500V K X7R 0.001uF 500V 125℃ 1.00 0.95 500V 118.8℃ 132.0V 113.2℃ PASS
RS1 RES NRWW 1/2W 0.3 J RAD 0.27Ω 0.5 0.37V 125 ℃ 1 125 0.37V 120 ℃ 0.170V 99.3 PASS
location Description Vcc Temp Vcc Temp Vcc Temp Vcc Temp
U1 IC LINEAR LEADTREND/LD7575 SMD 30V 150℃ 0.90 0.90 27V 135℃ 22.8V 98.6 ℃ PASS
LF2 CHOKE NB65A19 15mH 0.47mm IRON 120℃ 120℃ 111.1℃ PASS
DB1 D. PANJIT/PS206 2A 600V TAP 600V 1.1V 2A 150 ℃ 22 127 0.95 0.8 0.9 0.9 0.8
Do1 D ON/MBR20100CTG 100V20ASCKY 100V 0.57V 20A 150 ℃ 3.5 1.00 0.9 0.9 0.9
Q1 TR NMOS ST/STP10NK60ZFP10A600V 600V 30.0V 10.0A 150 ℃ 2.78 1.0 1 0.95 1 0.95 0.9 0.9
Test Data 344V 162V 19.0V 16.2V 0.73A 118.8℃ 120.3℃ PASS
CONCLUSION : OK NG
ISO-10-600-11 Rev1.0
Reliability Test Report
location Description Cap. Vmax Temp. Vmax Temp Vmax Temp Vmax Temp
Ck1 C AL120uF 400V M RAD 7.5105 KMG 120uf 400V 105℃ 1.00 0.95 400V 99.8 ℃ 326.0V 71.3 ℃ PASS
Co1 C AL330uF25V M RAD TAP5mm105 ℃ 330uf 25V 105℃ 1.00 0.95 25V 99.8 ℃ 18.5V 77.0 ℃ PASS
Co2 C AL330uF25V M RAD TAP5mm105 ℃ 330uf 25V 105℃ 1.00 0.95 25V 99.8 ℃ 18.6V 75.3 ℃ PASS
CH1 C AL22uF 50V M RAD TAP 22uf 50V 105℃ 1.00 0.95 50V 99.8 ℃ 23.0V 80.3 ℃ PASS
Ca1 CAP CHIP CER MULTI. 1nF500V K X7R 0.001uF 500V 125℃ 1.00 0.95 500V 118.8 ℃ 332.0V 87.0 ℃ PASS
RS1 RES NRWW 1/2W 0.3 J RAD 0.27Ω 0.5 0.37V 125 ℃ 1 125 0.37V 120 ℃ 0.215V 90.3 PASS
location Description Vcc Temp Vcc Temp Vcc Temp Vcc Temp
U1 IC LINEAR LEADTREND/LD7575 SMD 30V 150℃ 0.90 0.90 27V 135℃ 23.0V 80.4℃ PASS
LF2 CHOKE NB65A19 15mH 0.47mm IRON 120℃ 120℃ 71.1 ℃ PASS
DB1 D. PANJIT/PS206 2A 600V TAP 600V 1.1V 2A 150 ℃ 22 127 0.95 0.8 0.9 0.9 0.8
Do1 D ON/MBR20100CTG 100V20ASCKY 100V 0.57V 20A 150 ℃ 3.5 1.00 0.9 0.9 0.9
Q1 TR NMOS ST/STP10NK60ZFP10A600V 600V 30.0V 10.0A 150 ℃ 2.78 1.0 1 0.95 1 0.95 0.9 0.9
CONCLUSION : OK NG
ISO-10-600-11 Rev1.0
Reliability Test Report
location Description Cap. Vmax Temp. Vmax Temp Vmax Temp Vmax Temp
Ck1 C AL120uF 400V M RAD 7.5105 KMG 120uf 400V 105℃ 1.00 0.95 400V 99.8℃ 374.0V 80.8℃ PASS
Co1 C AL330uF25V M RAD TAP5mm105℃ 330uf 25V 105℃ 1.00 0.95 25V 99.8℃ 19.8V 86.4℃ PASS
Co2 C AL330uF25V M RAD TAP5mm105℃ 330uf 25V 105℃ 1.00 0.95 25V 99.8℃ 19.9V 85.0℃ PASS
CH1 C AL22uF 50V M RAD TAP 22uf 50V 105℃ 1.00 0.95 50V 99.8℃ 23.4V 83.0℃ PASS
Ca1 CAP CHIP CER MULTI. 1nF500V K X7R 0.001uF 500V 125℃ 1.00 0.95 500V 118.8℃ 384.0V 96.2℃ PASS
RS1 RES NRWW 1/2W 0.3 J RAD 0.27Ω 0.5 0.37V 125 ℃ 1 125 0.37V 120 ℃ 0.251V ℃
90.3 PASS
location Description Vcc Temp Vcc Temp Vcc Temp Vcc Temp
U1 IC LINEAR LEADTREND/LD7575 SMD 30V 150℃ 0.90 0.90 27V 135℃ 23.4V 85.7℃ PASS
LF2 CHOKE NB65A19 15mH 0.47mm IRON 120℃ 120℃ 80.0℃ PASS
T1 TX 41:7:8 FER CQ25 630uH 110 ℃ 110℃ 110℃ 110℃ 40℃ 94.0℃ 86.6℃ 54℃ PASS
DB1 D. PANJIT/PS206 2A 600V TAP 600V 1.1V 2A 150℃ 22 127 0.95 0.8 0.9 0.9 0.8
Do1 D ON/MBR20100CTG 100V20ASCKY 100V 0.57V 20A 150 ℃ 3.5 1.00 0.9 0.9 0.9
Q1 TR NMOS ST/STP10NK60ZFP10A600V 600V 30.0V 10.0A 150 ℃ 2.78 1.0 1 0.95 1 0.95 0.9 0.9
Test Data 595V 423V 19.0V 16.2V 0.40A 101.2℃ 101.6℃ PASS
CONCLUSION : OK NG
Reliability Test Report
6.7 Mean Time Between Failures Test Page 36
Model No.: NB-65B19 Sample S/N: 09 Test By:: lixu
Sample Rev.: 1.0 Check By: dss
6.7.1 Test Requirement:
This test is to verify whether the power adapter’s MTBF to meet the requirement of specification,
Condition:
Input: 90Vac/47HZ, 265Vac/63Hz
Output: Full Load (19Vdc/3.42A)
Ambient:40 ℃
The criteria of pass or fail :
The MTBF should be more than 100000 Hrs.
When the test result conform to Telcodia SR-332,the test item is passed.
6.7.2 Test Equipment and block diagram:
1) Oscilloscope: TDS 3014B
2) Ac source: Chroma 6408
3) Electronic load: Chroma 63010
4) Thermal recorder: YOKOGAWA DR230
5) Multimeter: FLUKE 45
Thermal Recorder
EUT
AC Input Output DC Load
AC EUT Source
Input Output DC Load
Source
Temperature chamber
Oscilloscope
CONCLUSION : OK NG
ISO-10-600-11 Rev1.0
Standard : Telcordia SR-332 Page 37
Model : NB-65B19
Product : Switching Power Supply Ambient Temperature : 40 ℃
Vin : 90V/ 47Hz
Ele Cap. CK1 400 105 120 132.0 40 98.2 15 1 0.665 10.221 1 9.808E+06
Ele Cap. Co1 25 105 330 19.8 40℃ 99.1℃ 15 1 2.015 10.535 1 3.140E+06
Ele Cap. Co2 25 105 330 19.9 40℃ 97.6℃ 15 1 2.035 10.016 1 3.271E+06
Ele Cap. Ch1 50 105 22 22.8 40℃ 90.9℃ 15 1 0.900 7.954 1 9.315E+06
Ceramic Ca1 500 125 0.001 132.0 40℃ 90.2℃ 1 1 0.380 1.292 1 2.037E+09
Remark 1 : λ SSi=λG *Π Q*ΠS*ΠT *Π E (Failures/109 Hours), MTBF1 = 1/ λ SSi*109 = 1,199,040.49 hrs
Res Rs1 0.5 125 0.27 0.17 40 99.3 0.5 1 0.690 2.424 1 1.196E+09
Remark 2 : λ SSi=λG *Π Q*ΠS*ΠT *Π E (Failures/109 Hours), MTBF2 = 1/ λ SSi*109 = 1,196,409,385.95 hrs
D. PANJIT/PS206 2A 599V TAP DB1 600 150 2 131.0 40 114.3 6 1 1 4.7792 1 3.487E+07
D. PANJIT/PS206 2A 600V TAP DB4 600 150 2 130.0 40℃ 112.8℃ 6 1 1 4.6583 1 3.578E+07
D.CROWNPO/FR107 1A 1000VFRD TAP Dh1 1000 150 1 57.0 40℃ 105.8℃ 6 1 1 4.12227 1 4.043E+07
D.PANJIT/1N4007 1A 1000VREC TAP DA1 1000 175 1 246.0 40℃ 126.8℃ 6 1 1 5.87264 1 2.838E+07
D ON/MBR20100CTG 100V20ASCKY Do1 100 150 20 52.0 40℃ 110.7℃ 6 1 1.059715 4.49266 1 3.501E+07
Remark 3 : λ SSi=λG *Π Q*ΠS*ΠT *Π E (Failures/109 Hours), MTBF4 = 1/ λ SSi*109 = 6,888,944.83 hrs
Res Rs1 0.5 125 0.27 0.261 40 90.3 0.5 1 1.006 2.159 1 9.207E+08
Remark 2 : λ SSi=λG *Π Q*ΠS*ΠT *Π E (Failures/109 Hours), MTBF2 = 1/ λ SSi*109 = 920,747,345.41 hrs
D. PANJIT/PS206 2A 599V TAP DB1 600 150 2 374.0 40 84.6 6 1 1.429988878 2.76481 1 4.216E+07
D. PANJIT/PS206 2A 600V TAP DB4 600 150 2 376.0 40℃ 81.6℃ 6 1 1.443879132 2.6028 1 4.435E+07
D.CROWNPO/FR107 1A 1000VFRD TAP Dh1 1000 150 1 99.0 40℃ 89.9℃ 6 1 1 3.06855 1 5.431E+07
D.PANJIT/1N4007 1A 1000VREC TAP DA1 1000 175 1 488.0 40℃ 107.0℃ 6 1 1 4.21092 1 3.958E+07
D ON/MBR20100CTG 100V20ASCKY Do1 100 150 20 87.0 40℃ 97.6℃ 6 1 2.924138771 3.55134 1 1.605E+07
Remark 3 : λ SSi=λG *Π Q*ΠS*ΠT *Π E (Failures/109 Hours), MTBF4 = 1/ λ SSi*109 = 6,567,922.91 hrs
Thermal
Recorder
EUT
AC Input Output DC Load
AC EUT Source
Input Output DC Load
Source
Temperature chamber
Oscilloscope
Diodes 106.64949823
MOSFETS 144.99214399
MTBF 538099.01Hrs
CONCLUSION : OK NG
ISO-10-600-11 Rev1.0
Standard : Telcordia SR-332 Page 40
Model : NB-65B19
Product : Switching Power Supply Ambient Temperature : 25 ℃
Vin : 230V/ 50Hz
Ele Cap. CK1 400 105 120 326.0 25 71.3℃ 15 1 2.130 3.849 1 8.133E+06
Ele Cap. Co1 25 105 330 18.5 25℃ 77.0℃ 15 1 1.779 4.794 1 7.818E+06
Ele Cap. Co2 25 105 330 18.6 25℃ 75.3℃ 15 1 1.796 4.493 1 8.261E+06
Ele Cap. CH1 50 105 22 23.0 25℃ 83.8℃ 15 1 0.908 6.172 1 1.189E+07
Ceramic Ca1 500 125 0.001 332.0 25℃ 87.0℃ 1 1 1.959 1.274 1 4.008E+08
9 9
Remark 1 : λSSi=λG *ΠQ*ΠS*ΠT *ΠE (Failures/10 Hours), MTBF1 = 1/ λSSi*10 = 2,192,923.71 hrs
D. PANJIT/PS206 2A 599V TAP DB1 600 150 2 335 25 75.9℃ 6 1 1.184317509 2.31406 1 6.081E+07
D. PANJIT/PS206 2A 600V TAP DB4 600 150 2 340 25℃ 72.7℃ 6 1 1.213287155 2.16256 1 6.352E+07
D.CROWNPO/FR107 1A 1000VFRD TAP Dh1 1000 150 1 81 25℃ 80.4℃ 6 1 1 2.53996 1 6.562E+07
D.PANJIT/1N4007 1A 1000VREC TAP Da1 1000 175 1 444 25℃ 96.8℃ 6 1 1 3.49883 1 4.764E+07
D ON/MBR20100CTG 100V20ASCKY Do1 100 150 20 76 25℃ 88.7℃ 6 1 2.125484975 2.99778 1 2.616E+07
Remark 3 : λSSi=λG *ΠQ*ΠS*ΠT *ΠE (Failures/109 Hours), MTBF4 = 1/ λSSi*109 = 9,376,509.19 hrs
Rating
(7) Inductive devices Location
Temperature
25 77.2 1 / ( λG *ΠQ *ΠT *ΠE ) =MTBF(hrs)
Transformer T1 110 25 ℃ 83.8 ℃ 19 1 1.978775888 1 2.660E+07
Remark 7 : λSSi=λG *ΠQ*ΠT *ΠE (Failures/109 Hours), MTBF10 = 1/ λSSi*109 = 26,598,049 hrs