Академический Документы
Профессиональный Документы
Культура Документы
Module 3
2. A Transformer has 4500 secondary turns and 750 primary turns. Its
turns ratio is
a) 1:6
b) 6:1
c) 1/6
Answer:
3. Two inductive coils are placed in close proximity with each other at
90 degrees. The number of flux linkages is
a) 0
b) maximum positive
c) maximum negative
Answer:
a) Zero
b) Pulsed negative
c) Pulsed positive
Answer:
8. What shape is the waveform when the input pulse and the time base are
unequal?
a) Square
b) Rectangular
c) Saw tooth
Answer:
9. A sine wave has 5 amps RMS value. What is the peak value?
a) 6.37 amps
b) 7.07 amps
c) 10 amps
Answer:
10. In this circuit
3. In a delta-connected generator
a) line volts = phase volts, line current = root 3 times phase current.
b) line volts = phase volts, line current = phase current divided by root
c) line voltage = root 3 times phase voltage, line current = phase
current
Answer:
a) stop
b) change direction
c) continue to run in the same direction
Answer:
Answer:a
a) Integrator
b) Low pass filter
c) Differentiator
Answer:c
1. Glass is an example of a
a) paramagnetic material
b) diamagnetic material
c) coercive material
Answer:b
8. A galvanometer measures
a) millivolts
b) megohms
c) milliamps
Answer:c
4. A capacitor with double the area and double the dielectric thickness
will have
a) double the capacitance
b) half the capacitance
c) the same capacitance
Answer:c
9. An inductance/resistance motor is
a) better than a capacitance motor
b) restricted to low loads only
c) less efficient than a capacitance motor
Answer:a
a) 7 V
b) 21 V
c) 28 V
Answer:a
This is exam number 8.
1. A 4:1 step down transformer draws 115 V and 1 A. The output power
will be
a) 28.5 V at 4 A
b) 28.5 V at 16 A
c) 460 V at 0.25 A
Answer:a
5. When checking the s.g. of the electrolyte in a lead acid battery, you
should
a) check all cells because they may be different
b) check only the no. 1 cell because it is the master cell
c) check any cell because they will all be the same
Answer:a
6. If electrons are added to an atom it becomes
a) a positive ion
b) a negative ion
c) a neutral ion
Answer:b
Answer:a
10. The diagram shows a 200 V long shunt generator. What is the voltage
dropped across the series resistor?
a) 200 V
b) 0.12 V
c) 0.2 V
Answer:b
This is exam number 9.
4. This is a diagram of a
Answer:c
1. A 10 ohm resistor has a 14.14 V peak drop across it. What power is
dissipated?
a) 19.99 W
b)10 W
c) 1.414 W
a) maximum current
b)minimum current
c) zero current
10. Through which material will magnetic lines of force pass the most
readily?
a) aluminium
b)iron
c) copper
4. In a star wound primary transformer, how could you wind the secondary
winding?
a) star only
b)delta only
c) either delta or star
a) 1.33 Ohms
b)12 Ohms
c) 3 Ohms
9. A step up transformer has
a) one winding
b)two windings
c) three windings
4. A.C. value that can produce the same heat as D.C. is called
a) r.m.s value
b)average value
c) peak value
5. If a battery has got low internal resistance, then
a) on load voltage will be greater than no load voltage
b)no load voltage will be greater than on load voltage
c) no load voltage will be the same as on load voltage
a) Increases
b)Remains the same
c) Reduces
8. What effect do the electrons of one atom have upon the electrons of
another atom?
a) They repel each other
b)They attract each other
c) They have no effect on each other
9. What is a molecule?
a) The smallest part of a compound
b)The smallest part of an electron
c) The smallest part of an atom
10. A coulomb is
a) one ampere per second
b)one ampere x second
c) one second per ampere
3. An atom is
a) the smallest part of an element that retains its characteristics
b)the smallest part of a compound that can exist independently
c) the smallest particle of matter
4. A potentiometer varies
a) voltage
b)current
c) resistance
a) 1 ohm
b)2 ohms
c) 6 ohms
8. If service No. 1 is isolated from the supply busbar shown there will
be
8. What is the ratio of turns between the primary coil winding and the
secondary coil winding of a transformer designed to triple its input
voltage?
a) primary will have three times as many turns as its secondary
b)primary will have twice as many turns as its secondary
c) primary will have one-third as many turns as its secondary
1. When two coils are linked by a common flux, a voltage can be induced
in one by a changing current in the other. This process is known as
a) mutual induction
b)the magnetic effect
c) self induction
3. Some electric motors have two sets of field winding wound in opposite
directions so that the
a) speed of the motor can be more closely controlled
b)motor can be operated in either direction
c) power output of the motor can be more closely controlled
2. One Picofarad is
a) 1 x 1012 farad
b)1 x 10-6 farad
c) 1 x 10-12 farad
4. A non-magnetic metal
a) has no permeability
b)has high retentivity
c) is a poor conductor
a) 3A
b)6A
c) 12A
a) 12 Ohms
b)3 Ohms
c) 7.5 Ohms
3. Which wave form is stepped positive and negative with unequal length
sides?
a) Trapezoidal wave
b)Rectangular wave
c) Saw tooth wave
9. An electric current is
a) a surplus of free electron
b)an excitement of electrons in a metal
c) an ordered flow of electrons
2. Carbon has a
a) negative temperature coefficient
b)positive temperature coefficient
c) temperature coefficient of zero
8. If the current flowing into a junction is 5A, 3A, 4A in and 10A out.
What is the 5th wire carrying?
a) 2A in
b)2A out
c) 5A out
10. If 2 resistors, one red, yellow, black, gold and the other violet,
blue, black, silver were replaced by a single resistor. Ignoring
tolerance, what would the colour coding be?
a) Brown, black, brown
b)Brown, black, black
c) Black, brown, black
1. Germanium and silicon have how many electrons in their outer shell
a) 4
b)2
c) 6
2. If a free electron is given to another atom, that atom is a
a) positive ion
b)negative ion
c) valency atom
a) 26V
b)28V
c) 2V
a) 50V
b)200V
c) 150V
3. A transformer with a 5:1 ratio has a 24V output. What is the input
a) 120 V DC
b)4.8 V AC
c) 120 V AC
a) A to B
B to C
D to E
c) D to E
D to C
6. A capacitor rating is
a) the maximum continuous voltage it can take
b)the voltage it will rupture at
c) the voltage it will charge to
9. In AC generators, 0.637 is
a) RMS
b)average value
c) form factor
10. In a 3 phase generator, what angle are the phases to each other?
a) 180o
b)120o
c) 0o
This is exam number 41.
Answer
1. 2 3 4 5 6 7 8 9 10
A B C C B B B B C A
8. Two 2 volt 10AH cells are connected in series, the output voltage and
the capacity would be
a) 2 volt, 20 AH
b)4 volt 10 AH
c) 4 volt 20 AH
10. Referring to the drawing below, if the volts dropped across the 20
ohm resistor is 10 volts, the resistance of R1 is
a) 20 ohms
b)16 ohms
c) 2 ohms
7. The bridge circuit shown will be balanced when the value of the
unknown resistor R is
a) 18 ohms
b)14 ohms
c) 2 ohms
a) Potentiometer
b)Rheostat
c) Thermister
a) 54V
b)1.5V
c) 6V
a) 22A
b)3A
c) 47A
3. The Watt can be expressed as
a) Joules per second
b)Joules x seconds
c) Seconds per Joule
a) 4µF
b)36µF
c) 3µF
a) upwards
b)downwards
c) sideways
7. Copper is a
a) paramagnetic materials
b)ferromagnetic material
c) diamagnetic material
3. A sine wave of RMS value 7.07 volts has a peak to peak value of
a) 10.0 volts
b)0.707 volts
c) 20.0 volts
8. A series motor draws a high current on start, and then the current
reduces. This is due to
a) the resistance of the field and the armature in series
b)the back EMF
c) the resistance of the field and armature in parallel
a) 9 ohms
b)5 ohms
c) 7 ohms
This is exam number 49.
Answer
1. 2 3 4 5 6 7 8 9 10
A A B A A B A A A B
a) increase
b)decrease
c) stay the same
a) 12W
b)50W
c) 20W
8. A DC shunt motor has 28 volts applied. The current taken from the
armature of 2 ohms resistance is 1 amp. The BEMF is
a) 30 V
b)27 V
c) 26 V
6. A transformer has 500 turns on the primary and 100 turns on the
secondary. When connected to a 100 V supply, the output is
a) 500 V
b)20 V
c) 25 V
1. A transformer has 1200 turns primary and 4800 turns secondary. What
value of load resistance would be required to give a reflected impedance
of 1000 ohms
a) 1 kohm
b)4 kohm
c) 16 kohm
7. In a resistive/inductive motor
a) the resistor circuit must be disconnected after starting
b)is less efficient than a capacitor start motor
c) can only be used for light loads
6. When switching off the supply, the back EMF in a collapsing field in
an inductor
a) never exceeds forward EMF
b)can be multiple times bigger than forward EMF
c) is equal to forward EMF
10.
In this circuit, Rx is equal to
a) R3 x R2 ÷ R4
b)R3 x R4 ÷ R2
c) R2 x R4 ÷ R3
1. A transformer to supply a 24V load with a 5:1 turns ratio will have
what primary supply?
a) 120 VDC
b)48 VAC
c) 120 VAC
4. A transformer has 2000V, 500 turns on the primary and 50 turns on the
secondary. What would be the line voltage if the transformer were
Delta/Star connected?
a) 200V
b)346V
c) 450V
2. Phase angle is
a) the difference in degrees of rotation between 2 alternating voltages
or currents or a voltage and a current
b)the difference in degrees between the positive and negative parts of
an ac sine wave
c) the cosine of the peak value of an ac voltage
6. Motor slip is
a) the percentage of difference in speeds between the stator and rotor
fields
b)a shifting of the MNA of the motor
c) a symptom of a weak field
10.
In this circuit applied voltage is
a) Vt = IXC
b)Vt = IXL
c) Vt = I/R
3. Armature reaction is
a) reactive sparking
b)due to dirty or worn commutator
c) the MMF opposing rotation
of 1K ohm
a) 1 k ohm
b)4k ohm
c) 16k ohm
6. A shunt motor
a) gives constant torque with variations in speed
b)is constant speed
c) has high starting torque
8. The diagram shows a 200V long shunt generator. What is the voltage
accross the series resistor
a) 30V
b)6V
c) 10V
5. Five different value resistors all have the same voltage dropped
across them, how are the resistors connected?
a) In Series
b)In Parallel
c) In Series/Parallel
6.The input is 115V and is applied across the 300 turn portion. What is the
output?
a) 460V
b)115V
c) 28V
6. How would you find the direction of the current flow in an armature
located in a magnetic field?
a) Maxwells corkscrew rule
b)Flemings right hand rule
c) Flemings left hand rule
3. What happens if you reverse the supply to the field and armature of a
DC shunt motor?
a) Reverses direction of rotation
b)Continues to rotate in same direction
c) Fails to start
9. Power factor is
a) sin theta
b)cos theta
c) tan theta
7. What would you use for the core in a generator current transformer?
a) Air core
b)Laminated core
c) Steel Core
7.
This is a diagram of a
a) Light Dependant Resistor
b)Logarithmic Differential Resistor
c) Laser Diode Rectifier
8. A centrifugal speed switch is used
a) to cut out the resistor/inductor circuit on an AC motor
b)to cut out the capacitor circuit on an AC motor
c) to cut out the slow start resistor on an AC motor
9. Disconnecting one of the phases from a 3-phase motor will cause the
motor to
a) stop
b)run at 2/3 speed
c) run at the same speed
5. Magnetic flux
1
This is a diagram of a
a) Variable Voltage source
b)Variable Resistor
c) Variable Current source
2.
Find voltage at point "B"
a) 10V
b)7V
c) 26V
10. A generator supplies 150VAC phase and load is 10 Ohms per phase -
what is the phase current ?
a) 15 A
b)1.5 A
c) 25.5 A
10. f the speed of a coil in a magnetic field is doubled and the field
strength is doubled the output will
a) halve
b)stay the same
c) quadruple
5. XL is the symbol of
a) inductive reactance
b)capacitive reactance
c) impedance