Академический Документы
Профессиональный Документы
Культура Документы
SAMSUNG
SAMSUNG TFT-LCD PRODUCT
TFT-LCD PRODUCT INFORMATION
INFORMATION
MODEL
MODEL :: LTA150XH
LTA150XH -- L06
L06
Note : This is Product Information is subject to change after 3 months of issuing date.
Description
LTA150XH-L06 is a color active matrix liquid crystal display (LCD) that uses amorphous
silicon TFT (Thin Film Transistor) as switching components. This model is composed of
a TFT LCD panel, a driver circuit and a back light unit. The resolution of a 15” is 1024 x
768 and this model can display up to 16.2 millions colors.
Features
High contrast ratio, high aperture structure
TN (Twisted Nematic) mode
Wide Viewing Angle
High speed response
XGA (1024 x 768 pixels) resolution
Low power consumption
DE (Data Enable) only mode
LVDS (Low Voltage Differential Signaling) interface (1pixel/clock)
Compact Size Design
Applications
TV & Desktop monitors
Display terminals for AV application products
Monitors for industrial machine
* If the module is used to other applications besides the above, please contact SEC
in advance.
General Information
(1) Temperature and relative humidity range are shown in the figure below.
a. 90 % RH Max. (Ta ≤ 39 °C)
b. Maximum wet-bulb temperature at 39 °C or less. (Ta ≤ 39 °C)
c. No condensation
(2) 11ms, sine wave, one time for ±X, ±Y, ±Z axis
(3) 10-300 Hz, Sweep rate 10min, 30min for X,Y,Z axis
(39,90)
(50,50.4)
(60,27.7)
(-25,5)
Rising Tr - 5 10
Response (5)
msec
Time BM-7
Falling Tf - 20 25
Rx - 0.624 -
Red
Ry - 0.356 -
Gx - 0.280 -
Green Normal
Gy θL,R=0 - 0.585 -
Color θU,D=0
Chromaticity (7),(8)
(CIE 1931) Bx Viewing - 0.144 -
Blue Angle
By - 0.076 -
Wx - 0.280 -
White
Wy - 0.290 -
θL 60 70 -
Hor.
Viewing θR 60 70 -
(8)
CR≥10 Degrees
Angle SR-3
θU 50 60 -
Ver.
θD 50 65 -
Photo detector
Photo detector Field
SR-3 1°
Field
BM-7 2°
SR-3 : 50㎝
BM-7 : 50㎝
6 5 4 512
3 2 1
922
: Test Point
G max
CR =
G min
Gmax : Luminance with all pixels white
Gmin : Luminance with all pixels black
10%
0%
Vsync Frequency fV - 60 75 Hz
Note (1) The ripple voltage should be controlled under 10% of VDD.
(2) Differential receiver voltage definitions and propagation delay and transition time test circuit
a. All input pulses have frequency = 10MHz, tR or tF=1ns
b. CL includes all probe and fixture capacitance
Note a.
Note b.
(3) LVDS Receiver DC parameters are measured under static and steady conditions
which may not be reflective of its performance in the end application.
T
c) Dot Pattern
VDD
100%
90%
10%
GND
TRUSH=470㎲
Rush Current IRUSH can be measured when TRUSH. is 470㎲.
The back light unit is a direct type with 4 CCFTs ( Cold Cathode Fluorescent Tube )
The characteristics of two dual lamps are shown in the following tables.
Ta=25 ± 2°C
LCD 1
Inverter
Module
COLD (Black or White) 2
A
| IMax − IMin|
IUNI = × 100
IMax
Imax : Maximum lamp current
Imin : Minimum lamp current
(3) Lamp frequency which may produce interference with horizontal synchronous
frequency may cause line flow on the display. Therefore lamp frequency should be
detached from the horizontal synchronous frequency and its harmonics as far as
possible in order to avoid interference.
(4) Life time (Hr) is defined as the time when brightness of a lamp unit itself becomes
50% or less than its original value at the condition of Ta = 25±2°C and IL = 7.5mArms
(5) Designing a system inverter intended to have better display performance, power
efficiency and lamp reliability.
They would help increase the lamp lifetime and reduce leakage current.
a. The measurement should be done at typical lamp current.
b. The asymmetry rate of the inverter waveform should be less than 10%.
c. The distortion rate of the waveform should be √2 with ±10% tolerance.
- Inverter output waveform had better be more similar to ideal sine wave.
Asymmetry rate
Ip | Ip − I - p|
× 100
Irms
Distortion rate
I-p
Ip I -p
| | or | |
Irms Irms
Fig. Wave form of the inverter
(6) If an inverter has shutdown function, it should keep its output for over 1 second
even if the lamp connector is open. Otherwise the lamps may not be turned on.
DS90C385
THC63LVDM83A
Host System DF14A-20P-1.25H
24-bit RED0 51 48 9
RED1 52 TxOUT0- 5 RxIN0-
RED2 54 47 100Ω 10
RED3 55 TxOUT0+ 6 RxIN0+
RED4 56
RED5 3 46 11
RED6 50 TxOUT1- 8 RxIN1-
RED7 2 100Ω
45 12
GREEN0 4 TxOUT1+ 9 RxIN1+
GREEN1 6
GREEN2 7
11 42 15
GREEN3 TxOUT2- 11 RxIN2-
GREEN4 12 100Ω
41 16
GREEN5 14 TxOUT2+ 12 RxIN2+
GREEN6 8
GREEN7 10 40 17
BLUE0 15 TxCLKOUT- 14 RxCLKIN-
BLUE1 19 100Ω
39 18
BLUE2 20 TxCLKOUT+ 15 RxCLKIN+
BLUE3 22
BLUE4 23 38
17 19
BLUE5 24 TxOUT3- RxIN3-
BLUE6 16 100Ω 20
BLUE7 37
18 TxOUT3+ 18 RxIN3+
Hsync 27
Vsync 28
Enable 30
CLOCK 31
Note : The LCD Module uses a 100ohm resistor between positive and negative lines of each
receiver input.
Data Signal
Gray
Color Display Red Green Blue Scale
R R R R R R R R G G G G G G G G B B B B B B B B Level
0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 -
Blue 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 -
Green 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 -
Basic Cyan 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -
Color Red 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 -
Magenta 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 -
Yellow 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 -
White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R000
1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R001
Dark
0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R002
Gray ↑ . . . . . . . . . . . . . . . . . . . . . . . .
R003
Scale . . . . . . . . . . . . . . . . . . . . . . . .
∼
of . . . . . . . . . . . . . . . . . . . . . . . .
R252
Red ↓ . . . . . . . . . . . . . . . . . . . . . . . .
1 0 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R252
Light
0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R252
Red 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R252
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 G000
0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 G001
Dark
0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 G002
Gray ↑ . . . . . . . . . . . . . . . . . . . . . . . .
G003
Scale . . . . . . . . . . . . . . . . . . . . . . . .
∼
of . . . . . . . . . . . . . . . . . . . . . . . .
G252
Green ↓ . . . . . . . . . . . . . . . . . . . . . . . .
0 0 0 0 0 0 0 0 1 0 1 1 1 1 1 1 0 0 0 0 0 0 0 0 G252
Light
0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 G252
Green 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 G252
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 B000
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 B001
Dark
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 B002
Gray ↑ . . . . . . . . . . . . . . . . . . . . . . . .
B003
Scale . . . . . . . . . . . . . . . . . . . . . . . .
∼
of . . . . . . . . . . . . . . . . . . . . . . . .
B252
Blue ↓ . . . . . . . . . . . . . . . . . . . . . . . .
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 1 1 1 1 1 B252
Light
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 B252
Blue 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 B252
T
TxCLK OUT
RxCK IN
T/7
Line 1 R G B R G B R G B R G B
Line768 R G B R G B R G B R G B
Note (1) This product is DE only mode. The input of Hsync & Vsync signal does
not have an effect on normal operation.
(2) Test Point : TTL control signal and CLK at LVDS Tx input terminal in system
(3) Internal Vcc = 3.3V
TVD TVB
DE
TH
THD
DE
DCLK
TC
DATA
SIGNALS
TC
TCH TCL
DCLK 0.5
VCC
TDS TDH
DISPLAY 0.5
DATA
VCC
TES
DE 0.5
VCC
300㎲≤T1≤10msec
0≤T2≤50msec
0≤T3≤50msec
1sec≤T4
Back-Light
(Recommended)
500msec≤T5
100msec≤T6
The supply voltage of the external system for the Module input should be the same
as the definition of VDD.
Apply the lamp voltage within the LCD operation range. When the back light turns on
before the LCD operation or the LCD turns off before the back light turns off,
the display may momentarily show abnormal screen.
In case of VDD = off level,
please keep the level of input signals low or keep a high impedance.
T4 should be measured after the Module has been fully discharged between power off
and on period.
Interface signal should not be kept at high impedance when the power is on.
VDD Td
90%
80%
VCC
GND
Note (1) The above conditions are for the glitch of the input voltage.
(2) For stable operation of an LCD Module power, please follow them.
i.e., if typ VDD x 80% ≤ Vcc ≤ typ VDD x 90%, then Td should be less than 20ms.
7.1 Handling
(a) When the module is assembled, it should be attached to the system firmly
using all mounting holes. Be careful not to twist and bend the module.
(b) Because the inverter uses high voltages, it should be disconnected from power
source before it is assembled or disassembled.
(c) Refrain from strong mechanical shock and / or any force to the module.
In addition to damage, it may cause improper operation or damage to the module
and CCFT back light.
(d) Note that polarizer films are very fragile and could be damaged easily.
Do not press or scratch the surface harder than a HB pencil lead.
(e) Wipe off water droplets or oil immediately. If you leave the droplets for a long
time, staining or discoloration may occur.
(f) If the surface of the polarizer is dirty, clean it using absorbent cotton or soft cloth.
(h) If the liquid crystal material leaks from the panel, it should be kept away
from the eyes or mouth . In case of contact with hands, legs or clothes, it must
be washed away with soap thoroughly.
(i) Protect the Module from static, or the CMOS Gate Array IC would be damaged.
(j) Use finger-stalls with soft gloves in order to keep display clean during the
incoming inspection and assembly process.
(n) Protection film for polarizer on the Module should be slowly peeled off just before use
so that the electrostatic charge can be minimized.
(o) Pins of I/F connector should not be touched directly with bare hands.
7.2 Storage
(a) Do not leave the Module in high temperature, and high humidity for a long time.
It is highly recommended to store the Module with temperature from 0 to 35℃
and relative humidity of less than 70%.
(c) The Module should be stored in a dark place. It is prohibited to apply sunlight or
fluorescent light in storing.
7.3 Operation
(a) Do not connect or disconnect the Module in the "Power On" condition.
(b) Power supply should always be turned on/off by the item 6.3
"Power on/off sequence"
(c) Module has high frequency circuits. Sufficient suppression to the electromagnetic
interference should be done by system manufacturers. Grounding and shielding
methods may be important to minimize the interference.
(d) The cable between the back light connector and its inverter power supply should
be connected directly with a minimized length. A longer cable between
the back light and the inverter may cause lower luminance of lamp(CCFT) and
may require higher startup voltage(Vs).
(b) If the product will be used in extreme conditions such as high temperature,
humidity, display patterns or operation time etc.., It is strongly recommended
to contact SEC for Application engineering advice. Otherwise, its reliability and
function may not be guaranteed. Extreme conditions are commonly found at
Airports, Transit Stations, Banks, Stock market, and Controlling systems.
7.5 Others
(c) Do not exceed the absolute maximum rating value. ( supply voltage variation,
input voltage variation, variation in part contents and environmental temperature,
and so on)
Otherwise the Module may be damaged.
(d) If the Module keeps displaying the same pattern for a long period of time,
the image may be "sticked" to the screen.
To avoid image sticking, it is recommended to use a screen saver.
(e) This Module has its circuitry PCB's on the rear side and should be handled
carefully in order not to be stressed.
(f) Please contact SEC in advance when you display the same pattern for a long time.