Академический Документы
Профессиональный Документы
Культура Документы
(rev. 1806)
Descrizione - Description - Description - Beschreibung
Descripcíon - Descrição
4
10
15
16 7
12
11
13
14
19
Kg 9,5
Pounds 21
IT LEGENDA EN LEGEND FR LEGENDE
Page
Index 1
Technical Programming Menu 2
Technical Menu Table 3
Grinder adjustment 4
English
1 EN
Technical Programming Menu
To access programming,
press the , , keys in rapid succession, holding the last one for 5 seconds.
English
MENU NO.
(P1, P2, etc.)
technical key
icon
Displayed values
By pressing the key (single cup), ACTIVE edit is activated (LED stops flashing and edit value starts
flashing)
The value can be edited with the and keys (the value does not flash while it is being edited)
Pressing the key (single cup) allows you to exit without saving (Return to MENU)
Pressing the key (double cup) allows you to save and exit (Return to MENU)
To exit the technical MENU, press and hold the key (double cup) for 5 seconds (the LED will stop
flashing and you will be taken to the normal work screen)
Note: If 20 seconds pass without pressing a key when not working on the main screen, the programming screen closes
automatically without saving, returning to normal functioning.
2 EN
Technical Menu Table
function inactive
function
active
3 EN
Grinder adjustment
English
• fine grinding › grind bar reduced, low reference value;
• course grinding › grind bar reduced, high reference value;
fine grinding
If the coffee dispensing takes a very long time, this means
that the coffee used is too finely ground. In this case, it is
necessary to turn the ring nut (4) anti-clockwise in order to grinding bar
obtain a coarser grinding level (number indications increasing:
reference
2 - 3 - 4 - ....).
value
grinding bar
reference
value
grinding times
reference reference
value value
grinding grinding
times times
reference reference
value value
4 EN
Ground coffee dose adjustment
single dose
1 2
English
Press the key (single dose); edit the single dose time using the and keys.
(in the example, it has increased by 0.5 seconds);
3 4
at the end of the operation, confirm your choices by or exit, leaving the previous choices, by pressing the
pressing the key (double dose); key (single dose).
5 EN
double dose
1 2
English
Press the key (double dose); edit the double dose time using the and keys.
(in the example, it has increased by 0.4 seconds);
3 4
at the end of the operation, confirm your choices by or exit, leaving the previous choices, by pressing the
pressing the key (double dose); key (single dose).
6 EN
“Zero” grinders
“Zero” grinders procedure (P3):
1 2
English
3 4
5 6
7 8
7 EN
9 10 11
English
12 13 14
function
inactive
A
P
Technical Mode
At this point, to enable the (Zero
Grinders) function, press the key
30° (single dose);
edit the (NO / Y) option using the
Turn the potentiometer (P) clockwise
Screw on the ring nut (A) until it just or keys;
as far as it will go, then turn it anti-
touches the grinders, and then turn it at the end of the operation, confirm
clockwise for roughly 2 full turns.
clockwise approximately 30°. your choice by pressing the key
(double dose);
15 reference
value
Note: After carrying out the “Zero Grinders” procedure
to activate the “Dose Correction” function, edit the coffee dose
times(P1)-(P2) in the technical menu.
8 EN
Automatic dose correction
Automatic dose correction (P4)
Maintenance
maintenance
icon
9 EN
Reset maintenance
English
NOTE: the (Reset) function displays the number of cycles
that were set initially.
function
active
10 EN
Manual dispensing counter (Reset)
11 EN
Load standard data
English
the key (double dose);
4. or exit, leaving the previous choice, by pressing the key
(single dose).
function
active
BDS function
active
12 EN
BDS (Barista Driving System)
OPERATING LOGIC
English
1 2
The LED keys on the machine are The associated keys will be enabled on
turned off. the machine, which can be recognised
by the relative LEDs lighting up.
13 EN
Check-control messages
English
DEFECT CAUSE REMEDY
Carry out maintenance After a certain number of cycles the Contact the technical service centre
technical key icon appears on the as soon as possible.
display on steady.
FLASH memory malfunction CPU board malfunction. CPU board fault. The anomaly does not block the
The fault is indicated by the technical key grinder/dispenser but the integrity of
icon flashing with a frequency of 2Hz (. the stored data is not guaranteed.
Consequently all stored parameters
. .. .. .. .. . . ). could be corrupt or restored to factory
settings.
If, after restarting multiple times, the
problem persists, contact the technical
service centre.
Data integrity error in non-volatile Data integrity error whilst loading the non- The anomaly does not block the
memory volatile memory during start-up. grinder/dispenser. However, normal
The fault is indicated by the technical key operation is not guaranteed, as all
icon flashing with a frequency of 1Hz (. stored parameters could be corrupt
or restored to factory settings.
... .... .... . . . . ). If, after restarting multiple times,
the problem persists, contact the
technical service centre.
14 EN
English
5 4
WIRING DIAGRAM 3 2 1
SW2 SW DPST
F M1
F AC F1 STYLE-1015 AWG18-NE AC
AC
CAVO ALIM faston 6.3
N AC
AC
N STYLE-1015 AWG18-BL MICRO
faston 6.3
SIC
GND N AC
faston 6.3
M2 VERSIONE 230V VERSIONE 115V
D Cod:965340000 D
N2 STYLE-1015 AWG18-BL
bianco-bianco rosso-bianco
1
nero-bianco
GND MOT
AC
GND STYLE-1015 AWG18-GV2
AC MATE-N-LOK MASCHIO 3P
faston 6.3 B C A C
3
F3 STYLE-1015 AWG18-NE
N STYLE-1015 AWG18-BL
N2 STYLE-1015 AWG18-BL
AC
A - rosso
B STYLE-1015 AWG18-BL AC
B - bianco
C STYLE-1015 AWG18-NE
C - bianco A
D STYLE-1015 AWG18-BL
D - nero D
1
2
3
4
5
6
7
8
F F N N F M N
J6
C LEOCO -5011S08000A C
FLAT 10P
J7 J8
1 2 1 2
3 4 3 4
5 6 5 6
7 8 7 8
9 10 9 10
15 EN
MICRO SIC
M2
AC
M1
AC
50mm 50mm
B
J7 J8 B
250mm
110mm
50mm
AC A - rosso
AC
50mm B - bianco
50mm 100mm
100mm C - bianco
D - nero
A 535793011 A
AC
F 50mm
J6
LEOCO
5011S08000A Rev. Date Description From
A 21/06/2011 TOLTO COLEGAMENTO POTENZIOMETRO
AC
N 1 21/07/2011 MODIFICATO CON J6 Title
IG A 11/10/2011 INVERTITI PIN OUT 5-8 DEL CONN J6 (FASE SUL 5 E NEUTRO SUL 8) <Title> Cablaggio ENEA OnDemand
07/11/2011 AGGIORNATO A COSTRUITO CON J6
Size Design File Name Rev
A3 <Doc> A
SW2 SW DPST
F F
AC F1 STYLE-1015 AWG18-NE
AC
CAVO ALIM faston 6.3
N AC N STYLE-1015 AWG18-BL M11
AC F1 STYLE-1015 AWG18-NE
D GND N faston 6.3
AB D
1
GND MOT
AC
GND STYLE-1015 AWG18-GV2
AC MATE-N-LOK MASCHIO 3P
faston 6.3
M21
F1A STYLE-1015 AWG18-NE AC
3
MICRO SIC
faston 6.3
F2 STYLE-1015 AWG18-NE AC
M22
535792002
C C
MICRO SIC
MOT
AC
AC
16 EN
MICRO 1
AB
AB
60mm
40mm
40mm
B 60mm B
GND
140mm AC
200mm
90mm
60mm
GUAINA NERA
350mm
60mm
A 60mm 535792001 A
AC
Rev. Date Description From
AC
IG Title
<Title> Cablaggio ENEA Mono F
Size Design File Name Rev
A3 <Doc>
English
Il Costruttore si riserva il diritto di modificare senza preavviso le caratteristiche
delle apparecchiature presentate in questa pubblicazione
The Manufacturer reserves the right to modify the appliances presented in this
publication without notice
Le fabricant se réserve le droit de modifier sans préavis les caractéristiques
des appareils présentés dans cette publication
Der Hersteller behält sich das Recht vor, die in dieser Veröffentlichung vorgestellten
Geräte ohne Vorankündigung zu ändern
El Constructor se reserva el derecho de modificar sin preaviso las
características de los equipos citados en este manual
O Constructor reserva-se o direito de modificar sem aviso prévio as
máquinas tratadas neste manual