List of Corrections in IS 800:2007 – Submitted for consideration at the meeting of BIS
committee CED:7 on 1st October, 2010, at BIS, Chennai
No Page Clause/Table/Fig Currently reads as Change to Section 17 Fabrication (17.15 missing) 17.15 Bedding requirement 1 iii and Erection 21st symbol Cmy, Cmz – moment Kz, Ky, KLT – moment 2 6 explanation amplification factors amplification factors (Cl. 4.4 about respective axes and Cl. 9.3.2.2) Table 2: Web of an I, H or box section – but ≥ 42ε 3 18 but ≤ 42ε Generally (under Class 1, Class 2 and Class 3) Table 2 Ratio for stem 4 18 D/tf d/t of a T-section… 5 18 Table 2 Last line overll overall Figure for ROLLED 6 19 Depth is marked as ‘h’ Should be ‘d’ CHANNELS 7 24 Cl 4.4.2, Cl 4.4.3.1 Cy,Cz Ky,Kz 8 24 Cl 4.4.3.3 Cmy, Cmz Ky,Kz 9 25 Cl.4.5.2 b) 12th line IS 2062 shall not be than IS 2062 shall not be less than Cl 5.6.1 Deflection. 2nd Table 6 gives Table 6 gives recommended column 6th line recommended limits of limits of deflections for deflections for certain certain structural members structural members and and systems. In Table 6, Live 10 31 systems. Circumstances load should include all post may arise…. construction loads including super imposed dead loads (SIDL). Circumstances may arise…. Cl. 6.3.3 (max. value of fu γmo/fy γm1 0.9 fu γmo/fy γm1 11 33 beta) Cl. 7.1.2 First line The design compressive The factored design strength Pd ,of a member compression, P, in the 12 34 is given by : members shall satisfy the following requirement: 13 34 Cl: 7.1.2.1 last line λm0 γm0 14 35 Fig.8 Abscissa (X- axis) title “λ” Table 10 Limits for 15 44 40 ≤mm < tf ≤ 100mm 40 mm < tf ≤ 100mm Rolled I- sections Table 11, Boundary at I Column II column I Column II column 16 45 one end – 2nd Case Free Restrained Restrained Free Cl. 7.5.1.2 end of the λe as given below λe as given below, in place of 17 48 first para λ in 7.1.2.1 and use curve ‘c’ (α=0.49) Cl. 7.5.1.2 Rewrite the equations for λvv = …λϕ=…
18 48
Top figure in Fig.10 Correct the horizontal axis as
19 49 z-z and vertical axis as y-y. 20 53 Cl. 8.2.1.1 3rd line d/tw ≤ 67ε d/tw > 67ε KL/r LLT/ry 21 57 Table 14 Heading h/tf hf/tf 1st para 3rd and 4th line length for lateral length for lateral torsional torsional buckling to be buckling, LLT, to be used in 22 58 used in 8.2.2.1 LLT shall 8.2.2.1 shall be be 1st para last three lines The effective length shall In the case of intermediate be equal to 1.2 times the partial lateral restraints, the length of the relevant effective length, LLT, shall be 23 58 segment in between the taken as equal to 1.2 times the lateral restraints length of the relevant segment in between the partial lateral restraints 24 58 Cl. 8.3.2 9th line at the shear and is at the shear centre and is Table 15 Case iii) Both flanges fully Both flanges partially 25 58 under warping restraint restrained restrained 26 59 Cl 8.4.2.1 ε and fy Read all ε as εw and fy as fyw Cl. 8.4.2.2 a) Definition of τcr,e = the elastic 27 60 tcr,e τcr,e critical shear stress of the web Second column second τb – buckling strength as Repeated and hence treat that 28 60 line obtained from 8.4.2.2.(a) as deleted. rd 29 60 Cl.8.5.1 – 3 line Carried in accordance Carried out in accordance Definition for ф ) = nearly equal to 30 60
Table 16 (last row i) Free The figure should be without 32 61 under top restraint top flange restraint conditions) 33 62 Fig. 12 Dimension arrow The dimension is ‘c’ 34 62 NOTES Item no 2 for Panel B is designed Panel B is designed using Figure 12 without utilizing the simple post critical method as tension field action as given in 8.4.2.2.(a) given in 8.4.2.2.(a) NOTES item no 2 for Treat item 2 as deleted and 35 63 Figure 13 item 3 becomes item 2 36 63 Cl.8.6.1.1 a) and b) All occurrences of ε εw 37 63 Cl.8.6.1.1 b) 3) When c < d When c < 0.74d Cl. 8.6.1.2 last line εf = yield stress ratio of εf = yield stress ratio of flange 38 64 web Cl. 9.3.1.2 c) for for n ≤ 0.2 Mndy=Mdy Mndz=1.11 Mdz (1-n) ≤ Mdz standard I or H sections for n > 0.2 Mndy=1.56 Mdy (1-n)(n+0.6) for n ≤ 0.2 Mndy=Mdy 39 70 Mndz=1.11Mdz(1-n) ≤Mdz for n > 0.2 Mndy=1.56 Mdy (1- n)(n+0.6)