Вы находитесь на странице: 1из 32

TITLE Disassembly and assembly instruction for PICO - DHN

VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009

Disassembly

Chapter 1, Removing the Battery Pack

To remove the battery pack from the battery bay,


follow the steps below:

1. Turn the notebook upside down.


2. Slide the battery lock in the direction of the
arrow to unlock the battery pack

3. Slide the battery release latch in the direction


of the arrow. The battery pack wills pop-up
automatically. Gently pry the battery pack
from its housing

NOTE: Always start laptop disassembly by


removing the battery pack first.

Page 1 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009

Chapter 2, Removing Memory

To remove the bottom cover, follow the steps below:

1. Remove the two screws pads as shown

2. Remove the two screws securing the Memory


cover as show

3. Open the Bottom case from left side.

Warning: Be care full Lift off the Memory


Cover can cause permanent damage for the
lower logic.

Page 2 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009

4. Push the latches to release the RAM module.


A spring will force one end of the module up

5. Grasp the memory module and remove from


main board.

Chapter 3, Removing the SSD Module

To remove the SSD Module, follow the steps below:

1. Remove the isolation tape.

2. Lever up with thumb the connector bracket


and disconnect the SSD Module cable from
the motherboard

3. Lift off the cable

Page 3 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009

4. Remove the two screws with screw driver to


remove the SSD Module from motherboard

5. Lift off the SSD Module form bottom casing

6. Remove the isolation tape.

7. Lever up with thumb the connector bracket


and disconnect the SSD Module cable from
SSD Card

8. Lift off the cable

Page 4 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009

Chapter 4, Removing the Keyboard

To remove the keyboard, follow the steps below:

1. Remove the screw pads as shown

2. Remove the two screws securing the


keyboard to the logic lower.

Page 5 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009

1. Turn the notebook over and push the latches


to release the keyboard

2. Pull the keyboard towards you, revealing the


keyboard cable underneath

3. lever up with thumb the connector bracket


and disconnect the keyboard cable from the
motherboard

4. Lift off the cable and remove the keyboard

Page 6 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009

Chapter 5, Removing the LCD Module

To remove the LCD Module, first remove the


battery pack, Logic Lower, Follow the steps below
to remove from the main board.

1. Remove the four screws securing the main


board to the logic upper.

2. Remove the metal plate.

Note : Please remember the position four


screws, installing wrong screw can cause
permanent damage for logic upper

3. Remove the cover hinge as show

4. Disconnect the CMOS, Speaker, LCD,


Antenna Wifi cable as shown

Page 7 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009

5. Release all the cable from logic lower

6. Remove the six screws securing the LCD

7. Remove the hand grip notebook as show

8. Remove the two screws securing the LCD


module

Page 8 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009

9. Gently remove the LCD Module

Page 9 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009

Chapter 6, Removing Keyboard Frame

To remove the Keyboard frame, first remove the


battery pack, LCD Module. Follow the steps below
to remove the Keyboard frame.

1. Remove the six screw pads as show.

2. Remove the ten screws securing the Logic


upper to the logic lower.

3. Remove the four screw pads as shown

4. Turn the notebook over

5. lever up with thumb the connector bracket


and disconnect the Touchpad and Touchpad
button cable from the motherboard

6. Remove The Screw securing the Logic upper


to the logic lower.

7. Gently remove the Keyboard frame

Warning: Be care full Lift off the keyboard frame


can cause permanent damage for the lower logic.

Page 10 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009

Chapter 7, Removing Touchpad Button

To remove the Touchpad Button. Follow the steps


below

1. Turn the Keyboard frame notebook upside


down.
2. Remove the three screw securing touchpad
frame to the logic upper.

Note : Please remember the position three


screws, installing wrong screw can cause permanent
damage for logic upper

3. Gently remove the touchpad button as show

NOTE: The touchpad module is attached to the rear of the logic upper and cannot be removed.

Page 11 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009

Chapter 8, Disassembly the Mainboard

To disassemble the Mainboard. Then follow these steps:

1. Remove the screw securing mainboard to the


logic lower as shown

2. Disconnect the Microphone cable as show

3. Gently remove the mainboard from the logic


lower.

4. Discconect the CMOS Battery

Warning: Be care full Lift off the LCD bezel can


cause permanent damage for the upper logic,
please attention for the key as show.

Chapter 9, Disassembly the Wifi Module

To disassemble the Wifi . Then follow these steps:

1. Turn over the Mainboard

2. Remove the screw securing the wifi to the


mainboard

3. Grasp the Wifi module and remove from


mainboard

Page 12 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009

Chapter 10, Disassembly the cooler fan

To disassemble the cooler fan. Then follow these


steps:

1. Disconnect the Fan cable as show

2. Remove the two screws securing the cooler fan


the mainboard.

3. Gently remove the cooler fan

Chapter 11, Disassembly the Display

To disassemble the display. Then follow these steps:

5. Remove the six screw pads as shown

Page 13 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009

6. Remove the six screws securing the LCD


bezel to the LCD module.

7. Carefully insert your fingers between the


display and the LCD bezel as indicated by
the arrow, and gently pry up the LCD bezel.

Warning: Be care full Lift off the LCD bezel


can cause permanent damage for the upper logic,
please attention for the key as show.

8. Remove the four screws mounting the


display.

9. Disconnect the Touch Screen cable as show.

10. Pull the keyboard towards you, revealing the


LVDS cable underneath

Page 14 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009

11. Remove the LVDS cable isolation tape

12. Disconnect the LVDS cable from the back of


the LCD.

13. Gently lift out the display. Remove the four


screws securing the hinges to the display.

Chapter 12, Removing Camera Module

To remove the camera module, first remove the LCD


module and lift out LCD display. Then follow these
steps:

1. Remove the two screws securing the CMOS


module to the LCD Frame

Page 15 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009

2. Remove the Upper case CMOC module as


show

3. Disconnect the CMOS cable from the CMOS


module as shown.

4. Gently remove the CMOS module from LCD


Frame

5. Remove the two screws securing CMOS


module to the CMOS case as show

6. Gently remove the CMOS module from


CMOS module.

Page 16 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009

Chapter 13, Removing LCD Button Board

To remove the LCD Button board, first remove the


LCD module and lift out LCD display. Then follow
these steps:

1. Remove the two screw securing LCD button


as show
2. Remove the LCD Button board

3. Disconnect The LCD Button Board cable as


show
4. Lift off the LCD Button Board.

Page 17 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009

Chapter 14, Removing the Speaker

To remove the speaker, first remove the LCD frame


and inverter Then follow the steps below

1. Remove the four screws securing the


speakers to the LCD module.

2. Lift out the speaker as shown.

3. Remove the two screws securing hinge to


the LCD frame

Page 18 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009

4. Remove the hinge with minus screw driver


as snow.

5. Remove the speaker cable from hinge as


show.

Assembly

Chapter 15, Assembly the Speaker

To assembly the speaker, follow the steps below

1. Remove the speaker cable from hinge as


show

Page 19 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009

2. Install the LCD Hinge cover to the LCD


hinge.

3. Tight the two screws securing hinge to the


LCD frame.

4. Tight the four screw securing speaker to the


LCD frame.

Chapter 16, Assembly LCD Button Board

To assembly the LCD Button board follow these


steps:

1. Connect The LCD Button Board cable as


show
2. Install the LCD Button Board
3. Tight the two screw securing LCD button as
show

Page 20 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009

Chapter 17, Assembly Camera Module

To assembly the camera module, follow these steps:

1. Tight the two screws securing CMOS module


to the CMOS case as show

2. Connect the CMOS cable to the CMOS


module as shown.

3. Gently install the CMOS module to CMOS


Frame

4. Tight the two screws securing the CMOS


module to the LCD Frame

Chapter 18, Assembly the Display

To assemble the display. Then follow these steps:

1. Tight the four screws securing the hinges to


the display.

Page 21 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009

2. Connect the LVDS cable from the back of the


LCD.

3. Tight the LVDS cable isolation tape

4. Tight the four screws mounting the display.

5. Connect the Touch Screen cable as show.

6. Gently pry down the LCD bezel to the LCD


Module.

7. Tight the six screw securing the LC bezel to


the LCD module as shown

8. Install the six screw pads as shown

Page 22 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009

Chapter 19, Assembly the cooler fan

To disassemble the cooler fan. Then follow these


steps:

1. Tight the two screws securing the cooler fan


the mainboard.

2. Connect the Fan cable as show

Chapter 20, Assembly the Wifi Module

To assemble the Wifi. Then follow these steps:

1. Push Wireless LAN at 30’ form main board,


push down and tight the screw

Page 23 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009

Chapter 21, Assembly the Mainboard

To Assemble the Mainboard. follow these steps:

1. Connect the CMOS Battery

2. Install the mainboard to the logic lower

3. Tight the screw securing the mainboard to


the logic lower

4. Connect the Microphone cable as show

Warning: Be care full Lift in the Mainboard can


cause permanent damage for button pin and please
intention for key as show.

Chapter 22, Assembly Touchpad Button

To Assembly the Touchpad Button. Follow the steps


below

4. Install the touchpad button

5. Tight the three screw securing touchpad


frame to the logic upper.

Note : Please remember the position three


screws, installing wrong screw can cause permanent
damage for logic upper

Page 24 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009

Chapter 23, Assembly Keyboard Frame

To assembly the Keyboard frames. Follow the steps


below.

1. Connect the Touchpad and Touchpad button


cable to from the motherboard

2. Tight The Screw securing the Logic upper to


the logic lower.

3. Turn the notebook upside down.

4. Tight the ten screws securing the Logic upper


to the logic lower.

5. Install the six screw pads as show.

Page 25 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009

Chapter 24, Assembly the LCD Module

To assembly the LCD Module to the notebook,


Follow the steps below;

1. Gently install the LCD Module

2. Tight the two screws securing the LCD


module

10. Tight the six screws securing the LCD

11. Tight the hand grip notebook as show

Page 26 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009

3. Connect the CMOS, Speaker, LCD, Antenna


Wifi cable as shown

4. Install the cover hinge as show

5. Install the metal plate.

6. Tight the four screws securing the main


board to the logic upper.

Note : Please remember the position four


screws, installing wrong screw can cause
permanent damage for logic upper

Page 27 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009

Chapter 25, Assembly the Keyboard

To Assembly the keyboard follow the step;

1. Lift in the cable and connect the keyboard


cable to the motherboard

2. Push the keyboard until latches at position


lock

3. Turn the notebook over and tight the two


screw securing the keyboard to the logic
lower.

Page 28 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009

4. Install the screw pads as shown

Chapter 26, Assembly the SSD Module

To Assembly the SSD Module, follow the steps


below:

1. Lift in the cable

2. Connect the SSD Module cable to SSD Card

3. Install the isolation tape.

4. Lift in the SSD Module form bottom casing

5. Tight the two screws with screw driver to


remove the SSD Module from motherboard

Page 29 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009

6. Connect the SSD Module cable to the


motherboard

7. Install the isolation tape.

Chapter 27, Assembly Memory

To assembly the bottom cover, follow the steps


below

1. Push memory at 30’ form main board and


push down until the Key at position lock

2. Key at Lock position, if the installation


corrects the pin will be invisible

Page 30 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009

3. Close the Memory and SSD cover

4. Tight the two screws securing the Memory


cover as show

5. Install the two screws pads as shown

Chapter 28, Assembly the Battery Pack

To install the battery pack to the battery bay, follow


the steps below:

1. Slide the battery lock latch in the direction of


the arrow. The battery lock wills pop-up
automatically.

Page 31 of 32
TITLE Disassembly and assembly instruction for PICO - DHN
VERSION 1.0
Prepared by: Donny Pinarendro Date: November 02, 2009
Approved by: Bambang Sie Date: November 02, 2009

2. Lock the secondary lock as show for more


safety

Page 32 of 32

Вам также может понравиться