Академический Документы
Профессиональный Документы
Культура Документы
SERVICE WARRANTY
Do not operate the unit with a damaged cord or plug, after the unit
malfunctions, has been dropped or damaged.
For your convenience, record the complete model number and product name
(located on the Product Identification Plate), the date you purchased the
product, and attach your purchase receipt as proof of purchase.
Should you have a problem with this product, please call our Help Desk on:
(0870) 742 5021.
As the colours of the wires in the mains lead of this appliance may not
correspond with the coloured markings identifying the terminals in your plug,
proceed as follows:
1. The BLUE wire is the NEUTRAL and must be connected to the terminal
which is marked with the letter N or coloured BLACK.
2. The BROWN wire is the LIVE and must be connected to the terminal
which is marked with the letter L or coloured RED.
3. The GREEN/YELLOW is the EARTH and must be connected to the
terminal which is marked with the letter E or or coloured GREEN OR
GREEN/YELLOW.
4. Always ensure that the cord grip is positioned and fastened correctly.
If a 13A (BS 1363) fused plug is used it must be fitted with a 13A (BS 1362)
fuse. If in doubt consult a qualified electrician.
1. Display window 7. Cord storage
Wiring for a 13 Amp Plug (BS 1363) 2. Control panel 8. Air filter
3. Buttons 9. Air inlet
Please note. The Earth Terminal is marked with the letter E or Earth Symbol
4. Air outlet 10. Exhaust air outlet / hose
5. Carrying handle connector
6. Caster 11. Air inlet
12. Water stopper/drainage
point
E. ACCESSORIES
Remote control
For Maximum Efficiency Press MODE button to select required working mode: automatic, cooling or
• Close doors and windows.
fan. The indicator of your selected mode comes on.
• Keep curtains and blinds closed during the sunniest part of the day.
• Regularly clean filters.
• Once room has reached the desired conditions, reduce temperature and Setting temperature
ventilation settings.
1. Press 'Temperature up' or 'Temperature down' button to set the desired
temperature.
2. The display window will show the temperature you set as you press
'Temperature up' or 'Temperature down' button. Otherwise, it will always
show the ambient temperature.
If you wish to operate the unit without the need to empty, you can fit the
NOTE optional drain hose.
1. To prolong the compressor's life, after switching off the unit, please wait
1. Remove the drain cap and
forat least 3 minutes before switch back on. rubber plug, and retain for
future use. Connect the drain
2. The cooling system will switch off if the ambient temperature is lower
tube supplied as shown and
than the termperature set. The ventilation, however, keeps working on locate the other end into a
the set level. If the ambient temperature rises above the selected level, drain.
the cooling system will start operating. 2. The drain tube may be
extended by adding
an extension tube and using a
H. DRAINAGE suitable connector, (not
supplied by the manufacturer)
Approx 18mm outer diameter.
NOTE: When the room humidity is over 85%, it is necessary to use
“continuous drainage” with the extended drain tube. Please note
• The drain must be at or below the outlet level.
This unit is self evaporating and the condensate will vent out of the exhaust • Flashing W.F - ‘full water’ indicator will not function in this mode of
hose. However, during the coiling process any excess will collect in the drainage.
reservoir inside the unit.
Too noisy
• Drain any water in the unit before completely operating the unit on
ventilation only mode for a few hours, to thoroughly dry the inside. • Is the machine positioned unevenly, thus creating vibration?
• Clean or change the filter. • Is the floor underneath the machine uneven?
• Unplug and store the power cord as shown.
The compressor doesn’t run
• Replace in the original carton or cover for storage.
• It is possible the overheat protector for the compressor is in operation.
Wait for the compressor to cool down.