Академический Документы
Профессиональный Документы
Культура Документы
Manufactured in Kuwait by
Air Movement Products Division
Bader Al Mulla & Bros. Co. W.L.L.
Under license from E.H. Price Limited, Canada
Single Duct Terminal Units
SPV, SDV Series
Single Duct – Controller Type
Product Information
General Information
Model SDV
Price has, as a primary component of its
terminal unit line, the SPV (pneumatic
controls), SDV (digital controls) single duct
VAV assemblies. These units are designed
to control the air flow rate of conditioned
air into an occupied space in response to
a control signal, usually a thermostat. The
clean and efficient design of these single
duct terminal units result in a system
component which has minimal pressure
drop reducing fan horsepower require-
ments, and low noise generation for quiet
operation. A compact configuration makes
this unit easier to use in today‘s crowded
mechanical spaces or in retrofitting existing
systems.
Control options for this product line are
wide and varied with pneumatic, analog
electronic and state of the art direct
digital control available to suit most any
application. Most of the control options
utilize the exclusive Price SP300 multipoint
sensor for accurate duct air velocity pressure
measurement. This allows the terminals to
monitor the desired flow rate, as dictated by
the thermostat, and compensate instantly
for any changes in supply air pressure that
might tend to alter the supply volume. In BMB
other words, the net result is a pressure
independent variable air volume system.
In addition to the basic volume ✓ Product Selection Checklist
control assembly, a complete line of 1] Select Unit Inlet Size based on control and acoustic parameters.
accessories is offered to meet specific job 2] Select Control type (Pneumatic, Digital) based on system design.
requirements. Sound attenuators, multi- 3] Select Accessories (Multi-Outlet Adaptor, Attenuator) as required.
outlet adaptors and heating coils are all 4] Select Reheat Coil, if required.
available. These are factory assembled 5] Select Control Sequence based on system design.
to the basic assembly for shipment as an
integrated unit. • Full range of accessories available (i.e. as option. Stainless steel shaft for
Features: coils, attenuators, etc.). dampers available as option.
• Capacities ranging from 50 – 8000 cfm • Protective metal shrouds for digital
in 11 sizes. controls. Protective metal cover optional
for pneumatic controls.
• Pressure independent operation.
• Compact, lightweight design for ease of
• Can be used for VAV or constant volume
installation.
applications.
• 22 gauge zinc-coated steel housing (optional
• Available with pneumatic, or direct
20 gauge available).
digital controls.
• 1/2 in. [13] thick, min. 1.5 lb density fiberglass
• Factory calibrated to job requirements.
internal insulation – meets requirements for
• Individually adjustable minimum and NFPA90A and UL181. 3/4 in. [19] and 1 in.
maximum air volumes – easily field [25] insulation also available as an option.
adjusted.
• Special liners and insulations available
• SP300 multipoint sensor designed as options.
to maintain control accuracy indepen-
• Damper blade constructed of two layers
dent of field installation conditions.
of heavy gauge galvanized steel with a
• Gauge taps for measurement sandwiched peripheral gasket of cross
and balancing supplied with factory linked polyurethane foam to ensure
mounted pneumatic controls (optional tight seal and no damper deflection.
for digital controls by others).
Alternate material for damper seal
• Conveniently accessible externally available as option subject to
mounted controls.
manufacturer’s recommendation.
• Inlet connection bead offers a means for
secure flex duct connections. • Plated damper shaft with position indicator
• A full 2 in. inlet connection to secure is mounted in self-lubricating bearings.
flex and hard duct connections. Bronze bushings are also available
All Metric dimensions ( ) are soft conversion.
Imperial dimensions are converted to metric and rounded to the nearest millimetre.
Single Duct Terminal Units
SPV, SDV Series
Single Duct – Controller Type
Dimensional Data
5”
(127) Size 4 & 5 have 6”ø duct with inlet and
Optional Bottom Access Door (AD) dischage reducer as shown.
SDV8 Size 4 – 16 • 1/2 in. [13] thick, min. 1.5 lb density internal
insulation which meets requirements of NFPA 90A
and UL181. Optional 3/4 in. [19] and 1 in. [25] also
available.
• 22 gauge zinc-coated steel housing. Mechanically
sealed and gasketed, leak resistant construction.
• Rectangular discharge opening with slip and drive
cleat duct connection.
• Control assembly will be supplied as illustrated on
right hand side unless otherwise.
• Gauge taps are standard on units with pneumatic
Optional Bottom Access Door (AD) controls (optional with digital controls by others).
• Clean, dry, 20 psi [138 KPa] for pneumatic unit .
SDV5 Size 4 – 16 Optional NEMAT Controls Enclosure • Optional insulated access door 4 x 63/4" ( 102 x 171)
attached with 4 screws or optional latches.
Multi-Point Sensor 18 1/2” (470)
(Gauge Taps Optional) • Alternate material for damper seal available as option
subject to manufacturer’s recommendation.
• Bronze bushings are also available as options.
• Stainless steel shaft for damper available as option
4 3/4” (121)
Optional Bottom Access Door (AD)
Optional Access Door
Dimensional Data
SPV8 Size 24 x 16
3 89
5 3/16” (132)
Optional Bottom
5” (127) Access Door (AD)
• 1/2 in. [13] thick, min. 1.5 lb density internal insulation which
SDV5 and SDV8 Size 24 x 16 meets requirements of NFPA 90A and UL181. Optional 3/4 in. [19] and 1
in. [25] also available.
Multi-Point Sensor • 22 gauge zinc-coated steel housing. Mechanically sealed and gasketed,
3 89
(Gauge Taps Optional) leak resistant construction.
• Rectangular discharge opening with slip and drive cleat duct connection.
• Control assembly will be supplied as illustrated on right hand side unless
otherwise.
• Gauge taps are standard on units with pneumatic controls (optional with
digital controls by others).
• Clean, dry, 20 psi [138 KPa] control air required for pneumatic unit .
• Optional insulated access door 4 x 63/4" ( 102 x 171) attached with 4 screws
or optional latches
Optional Bottom
Access Door (AD) • Alternate material for damper seal available as option
subject to manufacturer’s recommendation.
• Bronze bushings are also available as options.
• Stainless steel shaft for damper available as option
IP Units (in.] SI Units[mm]
Unit L/s cfm Outlet Inlet Length Outlet Inlet Length
Size Range Range B C D E L B C D E L
24 x 16 0 – 3776 0 – 8000 38 18 23 7/8 15 7/8 19 965 457 603 403 483
Accessories
Not Insulated
Not Insulated AD - Access Door w/Screws
AD - Access Door w/Screws
Not Insulated 4” (102) 3/4”(171)3
x- 6Access
Not Insulated
Not Insulated AD4” (102) x 6Door w/Screws
/4”(171)
Not Insulated 4” (102) x 63/4”(171)
ADL - Access Door w/Snap
ADL - Access LatchesLatches
Door w/Snap
4” (102) 3/4”(171)3
x 6-(102)
ADL 4” Access
x 6 Door
/4”(171)w/Snap Latches
4” (102) x 63/4”(171)
ADQ - Access Door w/Quarter
ADQ - Access Turn Sash
Door w/Quarter Latches
Turn Sash Latches
Insulated Bottom Bottom
Insulated 3/4”(171)3
Access Door 4” (102)
ADQ x 6-(102)
4” Access
x 6 Door
/ 4 w/Quarter
”(171) Turn Sash Latches
Access
Insulated Door
Bottom Insulated Bottom Bottom
Insulated Downstream
Downstream
Access Door Access Door
Access Door Access Door (ADD) 4” (102) x 63/4”(171)
Insulated Bottom Access
Downstream Note: Optional
Door (ADD) top and bottom access door available (TB)
Note: Optional top and bottom access door available (TB)
61/2”(165)
61/2”(165) (Not Insulated)
Access Door Access Door (ADD)
(Not Insulated) Note: Optional top and bottom access door available (TB)
61/2”(165) (Not Insulated)
SI Units [mm]
Accessories
4 3/8”
(111) 6 3/8”
(162)
Accessories
311/16”
(94)
SDV c/w Integral Attenuator SDV c/w separate Attenuator
and R.H. Water Coil ATTSP, ATT5SP and R.H. Water Coil 73/8”
(187)
Unit MOA
SDV c/w separate Attenuator 143/8” (365)
Size 1/2” (13) Outlets
SDV c/w Integral Attenuator ATTSP, ATT5SP 73/4” (197)
4, 5, 6 6 in. [152]
7, 8 311/16” 8 in. [203]
SDV c/w Integral Attenuator SDV c/w separate Attenuator 9,10,12 (94) 10 in. [254]
and R.H. Water Coil ATTSP, ATT5SP and R.H. Water Coil 12 73/812
” in. [305]
All outlets c/w manual dampers. 14, 16 (187)
16 in. [406]
Standard MOA Outlet Arrangements
SDV c/w Integral Attenuator and Electric Coil ACS Adaptor Coupling Section*
1/2” (13)
Gauge Taps
Damper Normally Open - PKIT-NO
SDV c/w R.H. Water Coil SDV c/w R.H. Electric Coil
FB
Foil Board Liner System FB
This system integrates 4 lb. density rigid insulating material
with an aluminum foil facing. Exposed edges are coated with NFPA-90A
approved sealant.
The fiberglass insulation and aluminum foil liner complies with the
following industry standards and tests:
• UL 181 (Air Erosion)
• UL 181 (Mold Growth and Humidity)
• UL 723 (25/50) (Flame and Smoke)
• ASTM E 84 (25/50) (Flame and Smoke)
• ASTM C 665 (Fungi Resistance)
• ASTM C 1071 (Physical Properties)
Acoustic absorption of aluminum foil lined insulation is reduced compared
to standard unlined units. The aluminum foil liner is non porous, thereby
protecting the insulation from moisture. Damage to the liner can expose
fiberglass particles to the air stream.
The following thicknesses are available
• FB - 5/8 in. [16] thicks, R-value =2.6
• FB1 - 1 in. [25] thick, R-value = 4.2
FG
Fiberglass Line FG
This system integrates 1.5 lb. density insulating material to
provide lining and insulation characteristics.
Fiberglass insulation meets NFPA 90A requirements and complies with
the following industry standards and tests:
• ASTM C 1071 3/4” (19)
• UL 181 (Air Erosion)
• UL 181 (Mold Growth and Humidity)
• UL 723 (25/50) (Flame and Smoke)
• ASTM E 84 (25/50) (Flame and Smoke)
• ASTM C 665 (Fungi Resistance)
The following thicknesses are available
• FG50 - 1/2 in. [13] thicks, R-value = 2.1
• FG75 - 3/4 in. [19] thicks, R-value = 3.2
• FG1 - 1 in. [25] thick, R-value = 4.1
Cleanroom Construction
General Information fibrous particles from entering the primary airstream as air flows
Price single duct terminal units with cleanroom construction are through the unit. The proven design of the Price standard single
designed for those applications where indoor air quality (IAQ) duct terminal unit incorporates unique design features to provide
is critical. These units are ideally suited to hospital applications these benefits.
such as patient rooms, burn wards, operating rooms and Attenuators and multi-outlet attenuator sections are available and
laboratories as well as cleanrooms and other areas where are specifically designed to match these terminals with cleanroom
airborne particles are of concern. Today, when IAQ is a growing construction. These sections are shipped as an integral part of the
concern, the Price line of cleanroom terminals can be successfully terminal unit.
applied to regular commercial construction. Three options of cleanroon construction are offered to meet the
Terminals with cleanroom construction are designed to reduce the specific needs of various applications. The options are designated
risk of micro-organism growth within the terminal as well as prevent CRAF, CRWF, and FF.
FF
Fiber Free Foam Insulation System FF
This system integrates an engineered foam which provides excellent
insulating characteristics. The foam edges are self sealing due to
the material’s composition.
The engineered foam meets requirement of NFPA 90A and complies
with the following industry standards and tests:
• UL 181 (Air Erosion)
• UL 181 (Mold Growth & Humidity) (FF50) 1/2” (13)
or
• UL 723 (25/50) (Flame & Smoke) (FF) 3/4” (19)
• ASTM E 84 (25/50) (Flame & Smoke)
• CAN/ULC-102.2-M88 (Flame and Smoke)
Fiber free foam insulation totally eliminates the risk of
particles entering the airstream while maintaining thermal resistance
and acoustic absorption. An important advantage over other liner
systems is that even scrapes or punctures will not expose fibers
to the airstream. The foam also will not absorb water, reducing the
likelihood of mold or bacterial growth. Acoustic absorption of the
foam insulation is equivalent to aluminum foil faced insulation.
The following thicknesses are available
• FF50 - 1/2" (13) thick, R value =2
• FF - 3/4" (19) thick, R value =3
• FF1 - 1" (25) thick, R value =4
Cleanroom Construction
CRAF CRWF
Cleanroom Aluminum Foil System Cleanroom Woven Fabric System CRAF
This system integrates a rigid 4 lb. density This system integrates fiberglass insulating
fiberglass insulating material with an material with a woven fabric facing. All
aluminum foil facing. All edges are sealed edges are sealed with metal end caps and
with metal endcaps and corner angles corner angles to prevent particles from
to prevent particles from entering the air entering the air stream.
stream. The liner’s integrity is maintained where the
The liner’s integrity is maintained where the damper shaft penetrates the insulation by a
damper shaft penetrates the insulation by a flanged nylon bushing.To reduce risk of liner
flanged nylon bushing.To reduce risk of liner damage during installation, sealed-in-place
damage during installation, sealed-in-place s-cleats are provided at the discharge collar.
s-cleats are provided at the discharge collar. The fiberglass insulation and fabric liner
The fiberglass insulation and aluminum foil complies with the following industry
liner complies with the following industry standards and tests:
standards and tests: • UL 181 (Air Erosion)
• UL 181 (Air Erosion) • UL 181 (Mold Growth and Humidity) CRWF
• UL 181 (Mold Growth and Humidity) • UL 723 (25/50) (Flame and Smoke)
• UL 723 (25/50) (Flame and Smoke) • ASTM E 84 (25/50) (Flame and Smoke)
• ASTM E 84 (25/50) (Flame and Smoke) • ASTM C 665 (Fungi Resistance)
• ASTM C 665 (Fungi Resistance) • ASTM C 1071 (Physical Properties)
• ASTM C 1071 (Physical Properties) The woven fabric liner provides acoustic
Acoustic absorption of aluminum foil lined absorption equivalent to aluminum foil
insulation is reduced compared to standard faced insulation with slightly improved
unlined units.The aluminum foil liner is non- attenuation at high frequencies. The Fiberglass with
woven fabric facing
porous, thereby protecting the insulation fabric is more porous than aluminum foil,
from moisture. The smooth surface of the therefore moisture can be absorbed into
liner reduces the risk of micro-organisms the insulation. If the liner is damaged,
being trapped in the material and also fiberglass particles can be exposed to the
facilitates cleaning. Damage to the liner can air stream. The woven fabric liner has been
expose fiberglass particles to the air stream. specified in certain areas for many years
The following thicknesses are available and has a proven track record in health care
• CRAF - 5/8 in. [16] thick, R-value=2.6 applications, R value = 2.6.
• CRAF1 - 1 in. [25] thick, R-value =4.2 The following thicknesses are available
• CRWF - 3/4 in. [19] thick, R-value=3.2
• CRWF1 - 1 in. [25] thick, R-value =4.1
S–Cleats
• Sealed in place to reduce risk of damage
to liner during installation
Product Information
General Information
Price offers factory supplied and mounted
electric coils for single duct terminal units.
The electric coils come standard as a
side-mounted unit (slide-in type) and are
specifically designed to suit Price terminal
units. The heating elements are low watt
density and designed to minimize hot spots
and thermal cutout. This allows for a more
compact assembly making field installation
much easier and reducing shipping costs.
Price heaters offer a full range of options
and accessories to meet all customers'
needs. SCR (Silicon Controlled Rectifier) and
the Price exclusive 'Electronic Modulating
Control' are also available, offering numer-
ous benefits over conventional duct heater
control.
Benefits of Electric Reheat
Electric coils offer an alternative to water
reheat coils as an optional accessory for
single duct terminal units.
Some of the benefits include:
• No requirement for water lines.
• Low pressure drop across the coil
elements, which reduces central fan
horsepower requirements.
• Operate using standard building
electrical power.
Features
• Extremely compact design – 35 in.
housing length.
• Specially designed elements allow
for installation with minimal clearance
between the terminal and coil, resulting • All heaters come with an Automatic • An air switch is provided as
in an extremely compact assembly. This Reset thermal cutout to protect from standard to ensure air is passing over
allows for easier field installation and overheating in case the minimum air the coil before it will energize. This
reduced shipping costs. flow requirements are not met. ensures that the coil will not energize
• A Manual Reset thermal cutout is when the system fan is shut-down or
• Heaters are factory wired and tested
standard on all heaters. fails.
ensuring a high level of quality.
• Terminal housing is lined with 1/2 in. • A unique pressure sensing tap
• The heater controls can be
compatible with pneumatic, electronic, [13] thick, min. 1.5 lb density fiberglass strategically located to ensure
internal insulation which meets positive operation of the heater at low
or direct digital control.
requirements for NFPA90A and UL181. downstream static pressure.
• Heavy gauge zinc-coated steel electrical
Optional 3/4 in. [19] and 1 in. [25] also
enclosure and frame. • For stable operation of heater controls
available. Heater section in not insulated minimum discharge static pressure of
• Electric coil and air is
unless requested. 0.2 in. w.g. is recommended
matched to eliminate hot spots, provide
• Magnetic contactors or Pneumatic-
efficient heat transfer, and to maintain
Electric switches are provided as
element life.
standard on staged heaters for de-
• Hinged access door for the electrical
energizing or disconnecting power to
enclosure.
the heating element.
• Heaters are provided with Low Watt
Density elements to prevent overheating
and nuisance tripping of the thermal
overload protectors.
• High grade nickel chrome elements
provide maximum corrosion resistance
and extended element life.
• When needed, a Class II (24VAC) control
transformer is provided as standard
with heater controls.
All Metric dimensions ( ) are soft conversion.
Imperial dimensions are converted to metric and rounded to the nearest millimetre.
Single Duct Terminal Units
SPV, SDV Series
Single Duct – Controller Type
Performance Notes:
1. NCs are derived from sound power levels, which are 7. ∆Ps for terminal units with electric coil is equal to basic Typical Attenuation Values:
obtained in accordance with AHRI Standard 880-2011 unit. Resistance of the coil elements is negligible. Radiated Sound
and ASHRAE Standard 130-2008. 8. ∆Pt is the difference in total pressure from inlet to discharge Total Deduction Octave Band Mid Frequency, Hz.
2. NCs are derived from sound power levels which include of the unit.
125 250 500 1000 2000 4000
duct end corrections per AHRI Standard 880 -2011. 9. Pressure is given in Pa and in. w.g.
All Sizes 18 19 20 26 3 1 36
10. NC values are calculated based on typical attenuation
3. Blank spaces (--) indicate NCs less than 20. values outlined in Appendix E, AHRI Standard 885-2008, Discharge Sound
4. Asterisks (*) indicate minimum static pressure of the unit “A Procedure for Estimating Occupied Space Sound Levels Total Deduction Octave Band Mid Frequency, Hz.
exceeds the minimum operating pressure across the unit. in the Application of Air Terminals and Air Outlets.” 125 250 500 1000 2000 4000
5. Air flow is given in L/s and cfm. < 300 cfm 24 28 39 53 59 4 0
6. ∆Ps is the difference in static pressure from inlet to 300 – 700 cfm 27 29 40 51 53 39
discharge of the unit. > 700 cfm 29 30 41 51 52 3 9
Performance Notes:
1. Test obtained in accordance with ARI Standard 880-2008 3. Pressure given in Pascals, Pa; and inches water gauge.
and Ashrae Standard 130-2008
2. Airflow given in litres/second, L/s; and cubic feet/minute,
CFM
Single Duct - Controller Type
SPV-K, SEV-K, SDV-K Series
Performance Notes:
1. Test obtained in accordance with ARI Standard 880-2008 3. Pressure given in Pascals, Pa; and inches water gauge.
and Ashrae Standard 130-2008
2. Airflow given in litres/second, L/s; and cubic feet/minute,
CFM
Bader Al Mulla & Bros. Co. W.L.L.
Air Movement Products Division
Post Box 177, Safat, 13002, Kuwait
Fax: 2483 9725 Tel: 2481 5077 Ext. 721
e-mail: ampsales@almullagroup.com