Академический Документы
Профессиональный Документы
Культура Документы
CRAWLER DOZER
Page 1 of 4
Courtesy of Machine.Market
OPERATOR ENVIRONMENT BLADE SERVICE CAPACITIES
ROPS canopy Blade pitch (adjustable) 55°- 60° Fuel tank 65 gal (246 L)
Adjustable armrests Cutting edge Reversible and Engine oil w/filter 16.5 qt (15.6 L)
replaceable
Foot rests Engine oil w/o filter 17.3 qt (16.4 L)
Width 8.0 in (203 mm)
Retractable seat belt, 2 in (51 mm) Engine cooling system 34 qt (32 L)
Thickness 0.75 in (19 mm)
Vinyl suspension seat w/back adjustment Cooling system –
Headliner Cab w/heater and AC 34.3 qt (32.5 L)
Mirror Max. penetration 19 in (483 mm) Final drive (per side) 15 qt (14.2 L)
Entire structure tilts for access Width 67.4 in (1711 mm) Track rollers (ea.) 0.48 qt (0.45 L)
Cut width 64.4 in (1635 mm) Front idlers (ea.) 0.46 qt (0.49 L)
Ground clearance Carrier rollers (ea.) 0.31 qt (0.29 L)
INSTRUMENTATION
(shanks in top position) 16.7 in
Warning lights: (424 mm)
Air filter Points Replaceable OPERATING WEIGHTS
Alternator Unit equipped with ROPS, full fuel tank,
Max. number of shanks 3
Diagnostic fault indicator 170 lb (77 kg) operator, side shield, track
Tooth spacing – guides, backup alarm, horn, lights and
Engine coolant temperature
with 3 teeth 31 in (787 mm) rear retrieval hitch
Engine oil pressure
Hydraulic filter Hydraulic cylinder (double-acting) Long Track 27,858 lb (12 636 kg)
Low fuel level Diameter 4 in (102 mm) Wide Track 28,667 lb (13 003 kg)
Park brake engaged Stroke 10 in (254 mm)
LGP 29,365 lb (13 317 kg)
Service soon indicator Rod 2 in (51 mm)
Add-on weights –
Transmission filter
Drawbar 146 lb (66 kg)
Transmission charge pressure
Ripper (3 shank) 2,300 lb (1043 kg)
Gauges:
Battery voltage Winch 2,100 lb (952 kg)
Digital hourmeter/tachometer/diagnostic/ser- Front counterweight 1,091 lb (495 kg)
vice reminder
Cab 920 lb (417 kg)
Fuel level
ROPS heater 70 lb (32 kg)
Transmission oil temperature
Transmission speed indicator CELT chain 375 lb (170 kg)
Water temperature
Audible warnings:
Engine coolant temperature
Engine oil pressure
Low fuel level
Transmission charge pressure
Transmission/hydraulic temperature
1150K Page 2 of 4
Courtesy of Machine.Market
C
E
J
K
A
H
F B
I D
DIMENSIONS
Extra Long Track (XLT) Wide Track (WT) Low Ground Pressure (LGP)
BLADES
Blade width 120 in (3.05 m) 132 in (3.35 m) 132 in (3.35 m)
SAE blade capacity 3.8 yd3 (2.9 m3) 4.2 yd3 (3.2 m3) 4.2 yd3 (3.2 m3)
A. Blade lift above ground 38 in (965 mm) 38 in (965 mm) 38 in (965 mm)
B. Blade depth below ground 19 in (483 mm) 19 in (483 mm) 19 in (483 mm)
C. Blade angle both directions 25° 25° 17°
Blade tilt, each end (up to 8.3°) 17.3 in (439 mm) 19 in (483 mm) 19 in (483 mm)
Blade height 44 in (1118 mm) 44 in (1118 mm) 44 in (1118 mm)
D. Cast reach 15 in (381 mm) 14.2 in (361 mm) 11.2 in (284 mm)
E. Cut reach -.2 in (-5 mm) -.5 in (-13 mm) -3.5 in (-89 mm)
TRACKS
Track gauge 70 in (1.78 m) 78 in (1.98 m) 78 in (1.98 m)
Max shoe width 24 in (610 mm) 30 in (762 mm) 34 in (864 mm)
F. Track on ground 102 in (2.59 m) 102 in (2.59 m) 102 in (2.59 m)
Area of track on ground 4896 in2 (3.16 m2) 6120 in2 (3.95 m2) 6936 in2 (4.47 m2)
Ground pressure 5.7 psi (39.7 kPa) 5.0 psi (34.5 kPa) 4.23 psi (29.2 kPa)
DIMENSIONS
G. Height to top of ROPS 9 ft 4 in (2.83 m) 9 ft 4 in (2.83 m) 9 ft 4 in (2.83 m)
Height to top of cab 9 ft 4 in (2.83 m) 9 ft 4 in (2.83 m) 9 ft 4 in (2.83 m)
H. Ground clearance w/drawbar 14.9 in (379 mm) 14.9 in (379 mm) 14.9 in (379 mm)
Length –
I. Blade straight with drawbar 16 ft 6 in (5.03 m) 16 ft 6 in (5.03 m) 16 ft 6 in (5.03 m)
Blade straight with ripper 19 ft 7 in (5.97 m) 19 ft 7 in (5.97 m) 19 ft 7 in (5.97 m)
Width –
Blade straight 10 ft (3.05 m) 11 ft (3.35 m) 11 ft (3.35 m)
J. Blade angled 9 ft 3 in (2.82 m) 10 ft 2 in (3.10 m) 10 ft 2 in (3.10 m)
K. Over track 94 in (2.39 m) 106 in (2.69 m) 112 in (2.84 m)
NOTE: Ground clearance and overall height dimensions are with the grousers fully penetrated. Add 52.5 mm (2.07 in) if unit is on solid surface.
1150K Page 3 of 4
Courtesy of Machine.Market
STANDARD EQUIPMENT
OPERATOR’S COMPARTMENT POWERTRAIN UNDERCARRIAGE
ROPS/FOPS canopy Dual path infinitely variable, single-lever con- Hydraulic track adjusters
Vinyl suspension seat w/back adjustment trolled hydrostatic drive with electronic straight Case Lubricated Track Chain
tracking & counter-rotation, 4-position
Retractable seat belt, 2 in (51 mm) Permanently lubricated track and carrier rollers
forward/reverse ratio control
Adjustable armrests and idlers
Final drive – Triple reduction – helical gear/plan-
Foot rests Track adjuster guard
etary decelerator with hydrostatic drive
Tool storage area retardation Track guides (front and rear)
Headliner Automatic spring applied parking brake OTHER
Floor mat BLADE Backup alarm
Entire structure tilts for access 55° - 60° variable pitch with integral Horn
ENGINE adjustment tool Anti-vandalism package
Case Family IV 667TA/EDJ Single lever electro hydraulic control for blade Mirror
Automatic fan belt tensioner lift, angle and tilt Pre-cleaner
Integral engine oil cooling Lights - 2 front, 1 rear
Fuel filter Rear transmission guard
Dual element radial seal air cleaner Front pull hook
65 amp alternator
(2) 700 CCA 12-volt batteries
Anti-sandblast radiator
Engine side panels
OPTIONAL EQUIPMENT
OPERATOR’S COMPARTMENT BLADES SCREENS
Cab (w/heater, defroster, A/C, front windshield 120 in (3.05 m) XLT w/24 in (610 mm) shoes Rear ROPS and cab
washer and lights) 132 in (3.35 m) WT w/30 in (762 mm) shoes Side ROPS
ROPS heater 132 in (3.35 m) LGP w/34 in (864 mm) shoes Radiator brush
3 in (76 mm) seat belt
GUARDS OTHER
Deluxe air suspension seat
ROPS canopy brush guard Counterweight, front
HYDRAULICS CAB canopy brush guard Drawbar, short
4 spool hydraulic valve for field-installed ripper Center rockguard Drawbar, long
REAR MOUNTED EQUIPMENT Rear retrieval hitch
Ripper, 3 slot with 3 shanks Environmental drains
Turbine precleaner
Rear wiper for cab
Tool box for ROPS
PTO equipment pump for winch drive
Special paint
Case Extended Life Track
Grid heater
Additional lights (2 front, 1 rear)
NOTE: All specifications are stated in accordance with SAE Standards or Recommended Practices,
where applicable.
NOTE: All engines meet current EPA emissions requirements.
IMPORTANT: CNH America LLC reserves the right to change these specifications without notice and
without incurring any obligation relating to such change. CNH America LLC does not warrant the
safety or reliability of attachments from other manufacturers.
Case is a registered trademark of CNH America LLC. Any trademarks referred to herein, in association with goods
and/or services of companies other than CNH America LLC, are the property of those respective companies.
www.casece.com
Courtesy of Machine.Market
Powered by TCPDF (www.tcpdf.org)