Академический Документы
Профессиональный Документы
Культура Документы
TROOUBLE SHOOTING
Pre-Check
1. Check if power is supplied at Concent and Power Cord is connected properly before repair
2. Check by referring to the followings.
Start
Is Power of primery
DC -TRANS applied?
Check assembly of
wires and do
epairing
s Power of secondary
DC -TRANS applied?
Change DC-TRANS
Change PCB.
REG2/Change PCB
Is 5V terminal normal?
Change PCB.
REG1/Change PCB
Are wire connections of
PANEL PCB normal?
Do repairing
Ia PANEL PCBnormal?
44
TROOUBLE SHOOTING
12-2) When there is a trouble with Self Diagnosis
Start
Is Ambient Sensor
normal?
Change Ambient
Sensor
Connector contact
trouble/re-insertion
Is the connection wire between
MAIN PCB connector(CN32)and Temp Sensor normal
(upper part od door)?
Short between
connector Sensors
Is the voltage of both ends (0.5V>V Measured value)
of Ambient Sensor of MAIN PCB
Connector (CN32)normal?
Change Sensor
Check soldering
fault,short,
Lead Touch
Change PCB
45
TROOUBLE SHOOTING
2) R-Room Temp Sensor trouble
Start
Is R-Room Temp
Sensor normal?
Change Temp
Sensor
Is the insertion of MAIN PCB
connector(CN30) normal?
Connector contact
trouble/re-insertion
Is the connection between
MAIN PCB connector(CN30) and Temp
Sensor(ORANGE) normal?
Short between
connector Sensors
Is MICOM Pin#59
input voltage normal?
Check soldering
fault,short, Lead Touch
Change MAIN PCB
Start
Is F-Room Temp
Sensor normal?
Change Temp
Sensor
Is the insertion of MAIN PCB
connector(CN80) normal?
Connector contact
trouble/re-insertion
Is the connection between
MAIN PCB connector(CN80) and Temp
Sensor(yellow) normal?
Short between
connector Sensors
Is MICOM Pin#58
input voltage normal?
Check soldering
fault,short, Lead Touch
Change MAIN PCB
46
TROOUBLE SHOOTING
4) Defrost Sensor trouble
Start
Is Defrost Sensor
normal?
Change Defrost
Sensor
Is MAIN PCB (CN30)
insertion normal?
Connector contact
trouble/re-insertion
Is the connection wire
between MAIN PCB connector(CN30) and
Defrost Sensor (purple) normal?
Short between
connector Sensors
Is MICOM Pin#60
input voltage normal?
Check soldering fault,
short,Lead Touch
Change MAIN PCB
Start
Is Damper Heater
normal? (about 144ohm)
Change Damper
Is MAIN PCB Connector
(CN30) insertion normal?
Connector contact
trouble/re-insertion
Is MICOM Pin#54 input
voltage normal? (over 2V)
Normal connection
Is it conditionfor
Damper Off?
Make Damper Off
condition
Change MAIN PCB
47
TROOUBLE SHOOTING
12-3) When COMP does not operate
Pre-Check
1. If it doesnotpass5 min after a desired Temp reached, COMP does not operate.
2. During Defrost, COMP does not operate.
3. With the disconnected F-Sensor or R-Sensor, COMP does not operate because MAIN PCB
picks up theTemp as a desired level.
Start
Is ForcedOperation on?
Run Forced
Operation
Soldering checkout/
Change MICOM
orPCB
Is theIC05 #10
"LOW"?
Change or repair
IC05/Change PCB
Change or repair
RELAY/Change PCB
Is contact of CONNECTOR
CN70 #9 contact normal
Insert Connector
completely/Check its
connection
Does COMP ASS'Y
Function normally?
Change/repair COMP
48
TROOUBLE SHOOTING
12-4) When FAN & DAMPER does not operate
Note
"Check out the F-FAN with the Forced Operation selected"
1. F-FAN, R-Room DAMPER and COMP COOLING FAN remains off while COMP is turned off.
2. When Comp is ON, Damper does not always remain ON (including Forced Operaation) and
when R-Room temp reaches to set temp, Damper remains OFF.
3. When R-Room & F-Room get closeed after being opened, each Fan &Damper starts up
immediately. (Comp ON condition)
Start
Is it during
Forced Operation?
Is FANRELAY normal?
Is FANASS'Y normal?
49
TROOUBLE SHOOTING
2) When R-Room DAMPER does not operate
Start
Is DAMPER in
operating conditions?
Forced Operation/
Temp Increase
When using R600a Option Does DAMPER
operates with DOOR S/W
Is insertion of pressed?
Check CN31 of MAIN PCB DAMPER is
Connector normal? normal
Is DOOR S/W normal?
Change Does voltage of Change DOOR
PCB MICOMPIN #62,63 change? S/W
"0V, 5V"
Is insertion of CN90 of
MICOM #61 :F-DOOR MAIN PCB normal?
#63 :R-DOOR Check Connector
CN90 again
Are voltage of MICOM
Pin #43,44,45 outputed?
Check soldering/
Change PCB
Is DAMPER normal?
Change DAMPER
Check wire assembly and connections between Dampers
50
TROOUBLE SHOOTING
3) When COMP COOLING FAN does not operate
Start
Is COMP operating?
Operate Forced
Operation
Is itCOMP COOLING FAN
ON condition?
Stand by or FAN ON
condition Confirm FAN
operating condition
51
TROOUBLE SHOOTING
12-5) When Defrost does not operate
Pre-Check
1. With a shorted-out Defrost Sensor, the fridge operates normally excepting Defrost(The fault
can be picked up with self-diagnosis, POWER ON/OFF).
2. There will be Heating trouble with a shorted-out Temp FUSE, which contributes to Defrost
by natural Temp increase resulting in a Temp Control problem stemmed from the increased
COMP OFF time.
3. When Defrost Sensor is faulty as OPEN, Heating will not be terminated, and COMP will
remain off following the Temp FUSE short-off.(The fault can be picked up with
self-diagnosis, POWER ON/OFF)
Start
Is contact of Connector
N70(browwn) normal?
Check contact of
Connector CN70 again
Is Temp FUSE in EVAP.
normal?
Change Temp FUSE
Is Defrost Heater
shorted out?
Change EVAP. ASS'Y
Check wire assembly
52
TROOUBLE SHOOTING
Change PCB
53
TROOUBLE SHOOTING
12-6) When Alarm Sound continues without stop
Note
1. When Door gets open, Door Open alarm ("Ding Dong") goes off in 2 minutes with Door
pened.When Door remains open after this, the alarm goes off every minute.
2. When Door Switch is not pressed well, MICOM considers it as opened and alarming sound
goes off. Room Lamp becomes OFF in 10 minutessince it detectsDoor Open (based on
R600a).In this case, even though Door gets opened, Room Lamp does not comes ON.
Start
When using R600a Option
Is insertion of MAIN
PCB Connector (CN70)
(PURPLE) normal?
Connector
contact Is insertion of Contact trouble of
defedct, CN31 of MAIN PCB Connector, Insert
Re-insert normal? it again
Repair DOOR
S/W pressing part
Repair connection
part
Change PCB /Re-confirm operation
54
Diagnostics
2) When “Beep Beep” sound continues
Start
Is Forced Operation/
Defrost selected?
Cancel Forced Operation/
Defrost
Does buzzing sound
go off when plugging out and
plugging in again?
PCB is normal
Note
1. "Beep-Beep" sounds do not go off except Forced Operation & Forced Defrost.
2. It is checckableatPanel PCB when Forced Operation or Forced Defrost is selected, so when
error occurs, check it andcorrect theerror.
Start
Is Connector of Upper
Hinge Cover inserted well?
Re-insert Connector,
Check contacts
Is inssertion of PANEL
PCB Connector normal?
Re-insert PANEL PCB
Connector, Check contacts
Change PANEL PCB
55
TROOUBLE SHOOTING
Start
Is Connector of Upper
Hinge Cover inserted well?
Re-insert Connector,
Check contacts
Is inssertion of PANEL
PCB Connector normal?
Re-insert PANEL PCB
Connector, Check contacts
56
TROOUBLE SHOOTING
12-7) When Room Lamp does not light up
Note
1. Because Room Lamp is basically controled with Door Switch, PCB does not control it.
Start
Is DOOR SwitchOPEN?
DOOR SWITCH
OPEN
Is RoomLAMP(R,F)
normal?
Change LAMP
Change DOOR
SWITCH
Is MICOM#27,#30
HIGH (5V)?
R LAMP #30
F LAMP #27
Check LEAD
TOUCH / Change
PCB
Is MAIN PCB RELAY
normal (RY77,RE74)?
R LAMP RELAY RY77
F LAMP RELAY RY74
Check RELAY /
Change MAIN PCB
Check wires again / Change PCB
57