Академический Документы
Профессиональный Документы
Культура Документы
from Km 0.000 (Design Chainage) to Km 53.300 (Design Chainage) in the State of Chhattisgarh under
BharatMala on Hybrid Annuity Mode.
1
Four lane with Paved shoulder configuration of Bilaspur- Pathrapali Section of NH- 111 (New NH-130) from Km 0.000 (Design Chainage) to
Km 53.300 (Design Chainage) in the State of Chhattisgarh under BharatMala on Hybrid Annuity Mode.
All types of soils including, laterite, morrum which can be excavated by means
i) of mechanical excavator and/or manual (but does not require crow bar, pick axe, cum 11,751 51.00 599,311.20
chiselling or blasting)
All types of soils including, laterite, morrum weathered rock, decomposed rock,
ii) soft rock etc. which can be excavated by means of crow bar, pick axe, cum 1,469 126.00 185,081.40
mechanical excavator (but does not require chiselling or blasting)
By covered and controlled blasting in Hard Rock for complete as per Drawings,
iii)
Specifications and instruction of Engineer.
cum 1,469 326.00 478,861.40
Removal of unserviceable soil/ material including excavation, loading and
2.02 disposal with all lifts and leads, but excluding replacement by suitable soil as cum 235 70.00 16,451.40
per Technical Specifications Clause 305.
Construction of embankment with approved earth/ muroom obtained from
borrow pits with all lifts and leads, transporting to site, spreading, grading to
2.03 required slope and compacting to meet requirement of table 300-2 as per cum 1,099,798 170.00 186,965,624.30
approved drawing, Technical Specifications & MoRTH clause 305 and as directed
by Engineer In-charge.
Construction of embankment/ subgrade with suitable material obtained from
roadway, drainage excavation etc.with all lifts and leads, transporting to site,
2.04 spreading, grading to required slope and compacting to meet requirement of cum 1,349 121.00 163,254.41
table 300-2 as per approved drawing, Technical Specifications & MoRTH clause
305 and as directed by Engineer In-charge.
Construction of subgrade & earthen shoulder with approved muroom obtained
from borrow pits satisfying requirement of minimum soaked CBR as per
approved design with all lifts and leads, transporting to site, spreading, grading
2.05
to required slope and compacting to meet requirement of table 300-2 as per
cum 1,031,102 180.00 185,598,378.00
approved drawing, Technical Specifications & MoRTH clause 305 and as directed
by Engineer In-charge.
Providing & Filling in median and Island with approved material brought from
borrow pits, spread, sloped and compacted with all leads & lifts as per approved
2.06
drawing, Technical Specification, MoRTH clause 408 and as directed by Engineer
cum 56,759 170.00 9,649,030.00
In-charge.
2.07 Ground improvement with Vertical Drains (PVD) Sqm - -
Providing, laying & maintenance of the live sods of perennial turf forming grass
on embankment slope, verges or other locations shown on the drawing or as
directed by the engineer including preparation of ground, fetching of sods and
2.08
watering & maintaining for 1 year beyond COD as per approved drawing,
sqm 12,140 100.00 1,214,000.00
Technical specification, MoRTH specification and as directed by Engineer In-
charge.
Bill No. 3:GRANULAR SUB-BASE AND BASE COURSES -
Construction of Granular Sub-base (GSB) in proper grade & camber by
providing crushed graded aggregate as per designed Grading (As per Table 400-
1 & 400-2 of MoRTH) spreading in uniform layers of thickness, with motor grader
on prepared surface, and compacting with vibratory roller to achieve designed
MDD/ Soaked CBR including all machinery, manpower, tools & tackles, fuel,
3.01 consumables etc. complete, for thicknesses specified as per approved cum 160,100 1,224.00 195,962,400.00
Drawings, Technical Specifications & standard MoRTH specifications of clause
401 and instruction of Engineer in Charge.
- With material prepared by mixing mechanically using mix in place method with
rotavator or using Batching Plant at Optimum Moisture Content (OMC).
Page 2 of 24
Four lane with Paved shoulder configuration of Bilaspur- Pathrapali Section of NH- 111 (New NH-130) from Km 0.000 (Design Chainage) to
Km 53.300 (Design Chainage) in the State of Chhattisgarh under BharatMala on Hybrid Annuity Mode.
Providing, laying, spreading and compacting graded stone aggregate to Wet Mix
Macadam specification as per the Clause No. 406 of MoRTH including premixing
the Material with water at OMC in mechanical mix plant carriage of mixed
Material by tipper to site, laying in uniform layers with sensor paver in sub- base
3.02
/ base course on well prepared surface and compacting with vibratory roller to
cum 48,269 1,450.00 69,990,050.00
achieve the desired density including all machinery, manpower, tools & tackles,
fuel, consumables etc. complete as per approved drawing, Technical
specification, MoRTH specification and as directed by Engineer In-charge.
Providing and applying tack coat using bitumen emulsion at the rate of 0.225
kg/ sqm for bituminous surface and 0.25 kg/ sqm for granular surface on
prepared surface including cleaning of road surface using mechanical means/
4.02
mechanical broom and spraying with emulsion pressure distributor etc.
-
complete including all machinery, manpower, tools & tackles, fuel, consumables
etc. complete as per approved Drawings, Technical Specifications & standard
MoRTH specifications of clause 503 and instruction of Engineer in Charge.
Providing and laying Bituminous Concrete (BC) wearing course using VG40
grade bitumen with 100-120 TPH batch type hot mix plant producing an average
output of 75 tonnes per hour using crushed aggregates of specified grading,
premixed with bituminous binder as per approved mix design with minimum
4.04 bitumen @ 5.2 % of mix and filler, transporting the hot mix to work site, laying cum 9,815 3,200.00 31,408,000.00 Filler shall be in Bidder scope
with a hydrostatic paver finisher with sensor control to the required grade, level
and alignment, rolling with smooth wheeled, vibratory and tandem rollers to
achieve the desired compaction complete in all respects as per drawing and
Technical Specifications & MORTH specification clause No. 507 & 501.
Construction of dry lean cement concrete Sub- base over a prepared sub-grade
with coarse and fine aggregate conforming to IS: 383, the size of coarse
aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1,
aggregate gradation after blending to be as per table 600-1, cement content not
to be less than 150 kg/ cum, optimum moisture content to be determined during
4A1
trial length construction, concrete strength not to be less than 10 Mpa at 7 days,
cum 88,647 1,974.00 174,989,178.00
mixed in a batching plant, transported to site, laid with a paver with electronic
sensor, compacting with 8-10 tonnes vibratory roller, finishing and curing
complete as per approved Drawing, Technical Specifications and MoRTH clause
no. 601 as directed by Engineer In-Charge.
Providing and placing concrete work including cost of machinery & equipment,
manpower, materials, admixtures and consumables including staging &
scaffolding, handling & transportation, batching, mixing, transportation of
concrete, placing, vibrating to achieve compaction and curing, etc. at all
elevations for :
5.05
Plain Cement Concrete (PCC) as levelling course/ fill around foundations, pipes,
-
floors on grade, water retaining structures, equipment foundations, under
foundations etc. including formwork, scaffolding & staging, materials,
manpower, Tools & tackles, Consumables etc. all complete as per approved
drawing, Technical specification, MoRTH specification and as directed by
Engineer In-charge.
a) M-15 grade cum 3,047 2,655.00 8,089,785.00
Providing and placing concrete work including cost of machinery & equipment,
manpower, materials, admixtures and consumables including staging &
scaffolding, handling & transportation, batching, mixing, transportation of
concrete, placing, vibrating to achieve compaction and curing, etc. at all
elevations for :
Reinforced cement Concrete grade conforming to IS:456 with coarse sand and
5.06 graded hard stone aggregate 20 mm and down nominal size machine mixed at -
all heights / depths any shape, any position, thickness, including addition of
suitable plasticizer/ super plasticizer conforming to IS:9103 to achieve required
slump in concrete, . Preparation of top surface or chipping to receive grouting
including formwork, scaffolding & staging, materials, manpower, Tools &
tackles, Consumables etc. but excluding Reinforcement Steel all complete as
per approved drawing, Technical specification, MoRTH specification and as
directed by Engineer In-charge.
a) M - 20 grade (Abutment, returnwall in slab, headwall in Pipe) cum 759 2,826.00 2,144,934.00
b) M - 20 grade (Wing / Returnwall in Box) cum - -
c) M - 25 grade in Foundation cum - -
Providing and placing concrete work including cost of machinery & equipment,
manpower, materials, admixtures and consumables including staging &
scaffolding, handling & transportation, batching, mixing, transportation of
concrete, placing, vibrating to achieve compaction and curing, etc. at all
elevations for :
Reinforced cement Concrete grade conforming to IS:456 with coarse sand and
5.07 graded hard stone aggregate 20 mm and down nominal size machine mixed at -
all heights / depths any shape, any position, thickness, including addition of
suitable plasticizer/ super plasticizer conforming to IS:9103 to achieve required
slump in concrete, . Preparation of top surface or chipping to receive grouting
including formwork, scaffolding & staging, materials, manpower, Tools &
tackles, Consumables etc. but excluding Reinforcement Steel all complete as
per approved drawing, Technical specification, MoRTH specification and as
directed by Engineer In-charge.
Providing & Laying filter media with stone crushed aggregates underneath stone
boulder pitching on slopes with well packed material to specified thickness &
5.10
gradation complete with all leads and lifts as per approved drawings, Technical
cum 153 1,500.00 229,500.00
Specifications, MoRTH specifications and as directed by Engineer In-charge.
Page 4 of 24
Four lane with Paved shoulder configuration of Bilaspur- Pathrapali Section of NH- 111 (New NH-130) from Km 0.000 (Design Chainage) to
Km 53.300 (Design Chainage) in the State of Chhattisgarh under BharatMala on Hybrid Annuity Mode.
Providing and fixing PCC M 20 guard posts along road side, size250 mm dia, 600
mm high, above road level, 300 mm below road level, embedded in CC block of
5.18
M 15 size 500 mm x 500 mm x 400 mm all as per drawing, in accordance with
Nr. - -
clause 1700.
Providing and fixing GI drainage spouts with 150mm dia outlet embedded in
5.19 concrete as per approved drawing,Technical Specifications & MoRTH Clause Nr. 32 930.00 29,760.00
2705 as directed by Engineer In-charge.
Reinforced cement Concrete grade conforming to IS:456 with coarse sand and
6.06 graded hard stone aggregate 20 mm and down nominal size machine mixed at -
all heights / depths any shape, any position, thickness, including addition of
suitable plasticizer/ super plasticizer conforming to IS:9103 to achieve required
slump in concrete, . Preparation of top surface or chipping to receive grouting
including formwork, scaffolding & staging, materials, manpower, Tools &
tackles, Consumables etc. but excluding Reinforcement Steel all complete as
per approved drawing, Technical specification, MoRTH specification and as
directed by Engineer In-charge.
a) M-35 grade - Foundation cum 4,431 3,840.00 17,015,040.00
M-35 grade -Substructure cum 7,001 4,119.00 28,837,119.00
Providing and placing concrete work including cost of machinery & equipment,
manpower, materials, admixtures and consumables including staging &
scaffolding, handling & transportation, batching, mixing, transportation of
concrete, placing, vibrating to achieve compaction and curing, etc. at all
elevations for :
Reinforced cement Concrete grade conforming to IS:456 with coarse sand and
6.07 graded hard stone aggregate 20 mm and down nominal size machine mixed at -
all heights / depths any shape, any position, thickness, including addition of
suitable plasticizer/ super plasticizer conforming to IS:9103 to achieve required
slump in concrete, . Preparation of top surface or chipping to receive grouting
including formwork, scaffolding & staging, materials, manpower, Tools &
tackles, Consumables etc. but excluding Reinforcement Steel all complete as
per approved drawing, Technical specification, MoRTH specification and as
directed by Engineer In-charge.
a) in RC Box M30 cum 1,370 4,992.00 6,839,040.00
b) in RC Slab M35 cum - -
Page 5 of 24
Four lane with Paved shoulder configuration of Bilaspur- Pathrapali Section of NH- 111 (New NH-130) from Km 0.000 (Design Chainage) to
Km 53.300 (Design Chainage) in the State of Chhattisgarh under BharatMala on Hybrid Annuity Mode.
Providing and placing concrete work including cost of machinery & equipment,
manpower, materials, admixtures and consumables including staging &
scaffolding, handling & transportation, batching, mixing, transportation of
concrete, placing, vibrating to achieve compaction and curing, etc. at all
elevations for :
Reinforced cement Concrete grade conforming to IS:456 with coarse sand and
graded hard stone aggregate 20 mm and down nominal size machine mixed at
all heights / depths any shape, any position, thickness, including addition of
6.08 suitable plasticizer/ super plasticizer conforming to IS:9103 to achieve required -
slump in concrete, . Preparation of top surface or chipping to receive grouting
including formwork, scaffolding & staging, materials, manpower, Tools &
tackles, Consumables etc. but excluding Reinforcement Steel all complete as
per approved drawing, Technical specification, MoRTH specification and as
directed by Engineer In-charge.
Note : The item rate shall include all charges for Girder loading, transportation,
unloading, launching, placing etc. complete including cost of crane, trailer & all
other equipments.
Providing and placing concrete work including cost of machinery & equipment,
manpower, materials, admixtures and consumables including staging &
scaffolding, handling & transportation, batching, mixing, transportation of
concrete, placing, vibrating to achieve compaction and curing, etc. at all
elevations for :
Reinforced cement Concrete grade conforming to IS:456 with coarse sand and
6.09 graded hard stone aggregate 20 mm and down nominal size machine mixed at -
all heights / depths any shape, any position, thickness, including addition of
suitable plasticizer/ super plasticizer conforming to IS:9103 to achieve required
slump in concrete, . Preparation of top surface or chipping to receive grouting
including formwork, scaffolding & staging, materials, manpower, Tools &
tackles, Consumables etc. but excluding Reinforcement Steel & Prestressing
activities all complete as per approved drawing, Technical specification, MoRTH
specification and as directed by Engineer In-charge.
Note : The item rate shall include all charges for Girder loading, transportation,
unloading, launching, placing etc. complete including cost of crane, trailer & all
other equipments.
in PSC (Pre Stressed Concrete) I Girders - M-45 Grade Cu.m. 2,595.2 6,876.00 17,844,595.20
in RCC Slab above PSC Girder - M-45 Grade Cu.m. 5,472 6,876.00 37,626,159.60
c) in PSC Box Girders Cu.m. - -
Providing, Straightening, cutting, bending, placing in position at any elevation,
binding & fixing in position using 18/ 20 SWG annealed iron wires including
supplying binding wires, providing cover blocks, shifting, all materials,
manpower, Tools & tackles, Consumables etc. all complete as per approved
drawing, Technical specification, MoRTH specification and as directed by
Engineer In-charge.
6.10 -
- High yield strength deformed bars conforming to grade Fe 415/ Fe 500/ Fe 500
D of IS : 1786
Providing and laying Tack coat and 50mm thick Bituminous Concrete (BC)
wearing course over Deck Slab using VG40 grade bitumen with 100-120 TPH
batch type hot mix plant producing an average output of 75 tonnes per hour
using crushed aggregates of specified grading, premixed with bituminous binder
as per approved mix design with minimum bitumen @ 5.5 % of mix and filler, Emulsion shall be in Bidder
6.12
transporting the hot mix to work site, laying with a hydrostatic paver finisher
sqm 13,936 254.00 3,539,744.00
scope
with sensor control to the required grade, level and alignment, rolling with
smooth wheeled, vibratory and tandem rollers to achieve the desired
compaction complete in all respects as per drawing and Technical Specifications
& MORTH specification clause No. 507 & 501.
Providing and fixing GI drainage spouts with 150mm dia outlet embedded in
6.13 concrete as per approved drawing,Technical Specifications & MoRTH Clause Nr. 206 1,023.00 210,738.00
2705 as directed by Engineer In-charge.
Supplying and fixing of bearings complete as per drawings and Technical
6.14
Specifications Section 2000 and IRC:83.
-
Elastomeric bearing cucm 1,800,000 1.00 1,800,000.00
Supplying and fixing of bearings complete as per drawings, Technical
6.15
Specifications clause 2000 and IRC:83 (Part III) - 2002
-
All types of POT-PTFE Bearings - as per approved drawings and capacity as per
a)
Design requirements
No's 200 50,000.00 10,000,000.00
6.16 Expansion Joints -
Asphaltic Plug Expansion joint
Providing and laying of asphaltic plug joint to provide for horizontal movement
of 25 mm and vertical movement of 2 mm, depth of joint varying from 75 mm
to 100 mm, width varying from 500 mm to 750 mm (in traffic direction),
Cement shall be in Bidder
a) covered with a closure plate of 200mm x 6mm of wieldable structural steel Rmtr 477 7,440.00 3,548,880.00
conforming to IS: 2062, asphaltic plug to consist of polymer modified bitumen scope
binder, carefully selected single size aggregate of 12.5 mm nominal size and a
heat resistant foam caulking/backer rod, all as per approved drawings,
technical specifications & MoRTH
b) Filler type Expansion joint. Rmtr - -
Page 6 of 24
Four lane with Paved shoulder configuration of Bilaspur- Pathrapali Section of NH- 111 (New NH-130) from Km 0.000 (Design Chainage) to
Km 53.300 (Design Chainage) in the State of Chhattisgarh under BharatMala on Hybrid Annuity Mode.
Strip seal jt. in PSC Girder catering to maximum horizontal movement upto 70
mm
Providing and placing concrete work including cost of machinery & equipment,
manpower, materials, admixtures and consumables including staging &
scaffolding, handling & transportation, batching, mixing, transportation of
concrete, placing, vibrating to achieve compaction and curing, etc. at all
elevations for :
Providing and laying stone boulder pitching on slopes and for floor aprons
complete including excavation, surface dressing, levelling course, boulder Cement shall be in Bidder
6.19
placing, pointing etc complete as per drawings and Technical Specifications
cum 11,834 2,046.00 24,212,364.00
scope
Section 2500 of MoRTH.
Providing weep holes in abutments, wing walls, retaining walls, return walls, box
structures etc. with 100 mm dia AC/ PVC/ HDPE pipes complete as per approved
6.20
drawing, Technical specification, MoRTH specification 2706 and as directed by
Nr. 3,401 65.00 221,065.00
Engineer In-charge.
Painting with synthetic enamel of Bridge no. and span arrangement as per
6.21
drawing, IRC:7-1971 and directions of the Engineer
Nr. 14 279.00 3,906.00
Providing and painting of flood gauge on substructure in full height and 500 mm
6.22
width as per IRC: 67-2001 and the directions of the Engineer.
m - -
Providing, laying, fixing PVC pipe of approved quality in footpath kerb, crash
6.23 barrier, Rain water downtake pipes including all specials & accessories all -
complete as per approved drawing as directed by Engineer In-charge
b) 150 mm dia m 2,139 279.00 596,781.00
Supplying and providing two coats of synthetic enamel paint of asian paint or
equivalent to give an even shade applied to concrete surfaces of parapet/ crash
barrier, kerb etc. at various elevations including surface preparation, cracks/ pin
6.24 hole fillings etc & one coat of primer all of approved shade and quality complete sqm 8,152 167.00 1,361,384.00
to the satisfaction with all material, labour, staging, scaffolding etc. complete
as per approved drawing, Technical specification, MoRTH specification and as
directed by Engineer In-charge.
Providing and laying boulder apron complete including excavation, surface
Cement shall be in Bidder
6.25 dressing, levelling course, boulder placing, pointing etc complete as per cum 642 1,767.00 1,134,414.00
drawings and Technical Specifications Section 2500 of MoRTH. scope
Providing and fixing Tar Paper Bearing complete as per drawing and IRC:SP:13-
6.26
2004.
sqm 143 140.00 20,020.00
Providing and filling joint sealing compound in approach slab complete as per
6.27
Technical Specifications and drawing.
m - -
Providing Bored cast-in-situ M35 grade R.C.C. Pile in all types of soil
including soft rock (1200 dia) incl cost of all materials, labour, loading,
6.28
unloading, lead upto 5 km, curing, hire charges tech spec: 1100,1600,1700
m - -
excluding Reinforcement
Plain / Reinforced Cement Concrete M35 in pile caps complete as per drawing
6.29
and technical specification 1500, 1700, 2200.
Cum - -
Providing, cutting, bending and fixing in position of TMT bar reinforcement in
6.30
piles and pile caps structures complete as per Tech. Spec. Cl 1600 MT - -
6.31 Providing and laying MS Steel Liner for Piles (6mm thick) MT - -
6.32 Conducting Load Tests on Piles -
a) Initial Load Test on Pile -
Vertical load test MT - -
Horizontal load test MT - -
b) Routine Load Test on Pile -
Vertical load test MT - -
Horizontal load test MT - -
Bill No.7: UNDERPASSES -
Clearing and grubbing road land by mechanical means including uprooting rank
vegetation, grass, bushes, shrubs and trees girth upto 300mm, removal of
7.01 stumps of trees cut earlier, disposal of unusable materials and stacking of hac - -
usable material to be used or auctioned, with all leads and lifts as per Technical
Specifications Clause 201.
Earthwork in excavation for foundation of all type of structures, trenches, Pipe
culvert etc. including setting out, clearing & grubbing, removal of debris,
dewatering if required, strutting, shoring, if required (sheet piling not required),
dressing the sides, levelling to grade and bottom compaction, backfilling with
selected excavated material wherever required (backfilling including watering
and ramming in layers of 30cm compacted thickness to 95% standard proctor
7.02
maximum dry density, compacted, levelling and dressing) and disposal of all
-
unsuitable materials and transportation & dumping of all suitable material at
embankment/ subgrade location including all lead & lifts, loading, transporting,
unloading with all machinery, manpower, tools & tackles, fuel, consumables etc.
complete as per approved drawings, Specifications, MoRTH cls. 304 and as
directed by Engineer In-charge for the following:
All types of soils including, laterite, morrum which can be excavated by means
i) of mechanical excavator and/or manual (but does not require crow bar, pick axe, cum 6,914 100.00 691,400.00
chiselling or blasting)
Page 7 of 24
Four lane with Paved shoulder configuration of Bilaspur- Pathrapali Section of NH- 111 (New NH-130) from Km 0.000 (Design Chainage) to
Km 53.300 (Design Chainage) in the State of Chhattisgarh under BharatMala on Hybrid Annuity Mode.
By covered and controlled blasting in Hard Rock for complete as per Drawings,
ii)
Specifications and instruction of Engineer.
cum - -
Excavation in hard rock requiring chiselling with pneumatic rock breaker
attachment of poclain, Hydraulic Pavement breakers etc. (which cannot be
iii)
excavated by manual means of crow bar, pick axe & mechanical means of cum - -
excavator, etc. or in hard rock prohibited of blasting)
Back filling behind abutments, box structures, wing walls and return walls with
approved earth/ muroom obtained from borrow pits with all lifts and leads,
7.03 transporting to site, spreading, grading to required slope and compacting to cum - -
meet requirement of table 300-2 as per approved drawing, Technical
Specifications & MoRTH and as directed by Engineer In-charge.
Providing & Filling filter media with stone crushed aggregates behind
abutments, box structures, wing walls and return walls with well packed
material to specified thickness with smaller size towards the soil and bigger size
7.04
towards the wall complete with all leads and lifts as per approved drawings,
cum 2,203 1,400.00 3,084,200.00
Technical Specifications, MoRTH specifications and as directed by Engineer In-
charge
Providing and placing concrete work including cost of machinery & equipment,
manpower, materials, admixtures and consumables including staging &
scaffolding, handling & transportation, batching, mixing, transportation of
concrete, placing, vibrating to achieve compaction and curing, etc. at all
elevations for :
7.05
Plain Cement Concrete (PCC) as levelling course/ fill around foundations, pipes,
-
floors on grade, water retaining structures, equipment foundations, under
foundations etc. including formwork, scaffolding & staging, materials,
manpower, Tools & tackles, Consumables etc. all complete as per approved
drawing, Technical specification, MoRTH specification and as directed by
Engineer In-charge.
a) M-15 grade cum 732 2,655.00 1,943,460.00
M-15 grade (below app slab) cum 319 2,655.00 846,945.00
M-15 grade (annular filling) cum - -
M-15 grade (bed protection works) cum - -
Providing and placing concrete work including cost of machinery & equipment,
manpower, materials, admixtures and consumables including staging &
scaffolding, handling & transportation, batching, mixing, transportation of
concrete, placing, vibrating to achieve compaction and curing, etc. at all
elevations for :
Reinforced cement Concrete grade conforming to IS:456 with coarse sand and
7.06 graded hard stone aggregate 20 mm and down nominal size machine mixed at -
all heights / depths any shape, any position, thickness, including addition of
suitable plasticizer/ super plasticizer conforming to IS:9103 to achieve required
slump in concrete, . Preparation of top surface or chipping to receive grouting
including formwork, scaffolding & staging, materials, manpower, Tools &
tackles, Consumables etc. but excluding Reinforcement Steel all complete as
per approved drawing, Technical specification, MoRTH specification and as
directed by Engineer In-charge.
a) M-35 grade - Foundation cum - -
M-35 grade -substructure cum 1,217 3,933.00 4,786,461.00
Providing and placing concrete work including cost of machinery & equipment,
manpower, materials, admixtures and consumables including staging &
scaffolding, handling & transportation, batching, mixing, transportation of
concrete, placing, vibrating to achieve compaction and curing, etc. at all
elevations for :
Reinforced cement Concrete grade conforming to IS:456 with coarse sand and
7.07 graded hard stone aggregate 20 mm and down nominal size machine mixed at -
all heights / depths any shape, any position, thickness, including addition of
suitable plasticizer/ super plasticizer conforming to IS:9103 to achieve required
slump in concrete, . Preparation of top surface or chipping to receive grouting
including formwork, scaffolding & staging, materials, manpower, Tools &
tackles, Consumables etc. but excluding Reinforcement Steel all complete as
per approved drawing, Technical specification, MoRTH specification and as
directed by Engineer In-charge.
a) in RC Box M30 cum 9,642 4,062.00 39,165,804.00
b) in RC Slab M35 cum - -
c) in RC Girder & RC Slab M40 cum - -
Providing and laying Reinforced Cement Concrete M40 in superstructure
7.08 excluding reinforcement complete as per drawings and Technical Specifications -
Sections1500, 1700 and 2300
a) For solid slab super-structure cum - -
b) in PSC I Girders cum - -
Providing and laying Prestressed Cement Concrete M45 in SuperSturucture
7.09 complete as per drawings and Technical Specifications Sections 1500,1700,1800 -
and 2300.
a) in PSC I Girders Cu.m. - -
b) in PSC Voided slabs Cu.m. - -
c) in PSC Box Girders Cu.m. - -
Providing, Straightening, cutting, bending, placing in position at any elevation,
binding & fixing in position using 18/ 20 SWG annealed iron wires including
supplying binding wires, providing cover blocks, shifting, all materials,
manpower, Tools & tackles, Consumables etc. all complete as per approved
drawing, Technical specification, MoRTH specification and as directed by
Engineer In-charge.
7.10 -
- High yield strength deformed bars conforming to grade Fe 415/ Fe 500/ Fe 500
D of IS : 1786
Page 8 of 24
Four lane with Paved shoulder configuration of Bilaspur- Pathrapali Section of NH- 111 (New NH-130) from Km 0.000 (Design Chainage) to
Km 53.300 (Design Chainage) in the State of Chhattisgarh under BharatMala on Hybrid Annuity Mode.
Providing & fixing High Tensile Steel strands including all accessories for
stressing and jacking operations and grouting etc. complete as per approved
drawing, Technical specification, MoRTH specification and as directed by
Engineer In-charge including but not limited to following. All materials Other than HT
Strands shall be in scpoe of
7.11 All charges for providing, placing in position and profiling of strand, including MT - - bidder. Cement required for
cutting of strands to desired length , threading and tying in position, providing & grouting shall also be in scope
placing sheathing duct, providing & placing necessary anchorages, stressing of of bidder
strands, washing of strands and Grouting of cables as per drawing and
specification etc complete in all respect as per scope of work with cost of all
materials, equipment, labours, consumables, tool, tackles etc
Providing and laying Tack coat and 50mm thick Bituminous Concrete (BC)
wearing course over Deck Slab using VG40 grade bitumen with 100-120 TPH
batch type hot mix plant producing an average output of 75 tonnes per hour
using crushed aggregates of specified grading, premixed with bituminous binder
as per approved mix design with minimum bitumen @ 5.5 % of mix and filler, Emulsion shall be in Bidder
7.12
transporting the hot mix to work site, laying with a hydrostatic paver finisher
sqm 5,961 255.00 1,520,055.00
scope
with sensor control to the required grade, level and alignment, rolling with
smooth wheeled, vibratory and tandem rollers to achieve the desired
compaction complete in all respects as per drawing and Technical Specifications
& MORTH specification clause No. 507 & 501.
Providing and fixing GI drainage spouts with 150mm dia outlet embedded in
7.13 concrete as per approved drawing,Technical Specifications & MoRTH Clause Nr. - -
2705 as directed by Engineer In-charge.
Supplying and fixing of bearings complete as per drawings and Technical
7.14
Specifications Section 2000 and IRC:83.
-
Elastomeric bearing cucm - -
Supplying and fixing of bearings complete as per drawings, Technical
7.15
Specifications clause 2000 and IRC:83 (Part III) - 2002
-
All types of POT-PTFE Bearings - as per approved drawings and capacity as per
a)
Design requirements
No's - -
7.16 Expansion Joints -
Asphaltic Plug Expansion joint
Providing and laying of asphaltic plug joint to provide for horizontal movement
of 25 mm and vertical movement of 2 mm, depth of joint varying from 75 mm
to 100 mm, width varying from 500 mm to 750 mm (in traffic direction),
Cement shall be in Bidder
a) covered with a closure plate of 200mm x 6mm of wieldable structural steel Rmtr 576 9,300.00 5,356,800.00
conforming to IS: 2062, asphaltic plug to consist of polymer modified bitumen scope
binder, carefully selected single size aggregate of 12.5 mm nominal size and a
heat resistant foam caulking/backer rod, all as per approved drawings,
technical specifications & MoRTH
b) Filler type Expansion joint. Rmtr - -
Strip seal jt. in PSC Girder catering to maximum horizontal movement upto 70
mm
Providing and placing concrete work including cost of machinery & equipment,
manpower, materials, admixtures and consumables including staging &
scaffolding, handling & transportation, batching, mixing, transportation of
concrete, placing, vibrating to achieve compaction and curing, etc. at all
elevations for :
Providing and laying stone boulder pitching on slopes and for floor aprons
including excavation, surface dressing, levelling course, boulder placing,
7.19
pointing etc complete as per drawings and Technical Specifications Section
cum - -
2500 of MoRTH.
Providing weep holes in abutments, wing walls, retaining walls, return walls, box
structures etc. with 100 mm dia AC/ PVC/ HDPE pipes complete as per approved
7.20
drawing, Technical specification, MoRTH specification 2706 and as directed by
Nr. 3,670 65.00 238,550.00
Engineer In-charge.
Painting with synthetic enamel of Bridge no. and span arrangement as per
7.21
drawing, IRC:7-1971 and directions of the Engineer
Nr. 34 279.00 9,486.00
Providing and painting of flood gauge on substructure in full height and 500 mm
7.22
width as per IRC: 67-2001 and the directions of the Engineer.
m - -
Providing, laying, fixing PVC pipe of approved quality in footpath kerb, crash
barrier, Rain water downtake pipes, toll booth island including all specials &
7.23
accessories all complete as per approved drawing as directed by Engineer In-
-
charge
b) 150 mm dia m 749 279.00 208,971.00
Supplying and providing two coats of synthetic enamel paint of asian paint or
equivalent to give an even shade applied to concrete surfaces of parapet/ crash
barrier, kerb etc. at various elevations including surface preparation, cracks/ pin
7.24 hole fillings etc & one coat of primer all of approved shade and quality complete sqm 9,129 167.00 1,524,543.00
to the satisfaction with all material, labour, staging, scaffolding etc. complete
as per approved drawing, Technical specification, MoRTH specification and as
directed by Engineer In-charge.
Page 9 of 24
Four lane with Paved shoulder configuration of Bilaspur- Pathrapali Section of NH- 111 (New NH-130) from Km 0.000 (Design Chainage) to
Km 53.300 (Design Chainage) in the State of Chhattisgarh under BharatMala on Hybrid Annuity Mode.
Reinforced cement Concrete grade conforming to IS:456 with coarse sand and
8.06 graded hard stone aggregate 20 mm and down nominal size machine mixed at -
all heights / depths any shape, any position, thickness, including addition of
suitable plasticizer/ super plasticizer conforming to IS:9103 to achieve required
slump in concrete, . Preparation of top surface or chipping to receive grouting
including formwork, scaffolding & staging, materials, manpower, Tools &
tackles, Consumables etc. but excluding Reinforcement Steel all complete as
per approved drawing, Technical specification, MoRTH specification and as
directed by Engineer In-charge.
a) M-35 grade - Foundation cum 2,862 3,654.00 10,457,748.00
M-35 grade -substructure cum 2,272 3,933.00 8,935,776.00
Page 10 of 24
Four lane with Paved shoulder configuration of Bilaspur- Pathrapali Section of NH- 111 (New NH-130) from Km 0.000 (Design Chainage) to
Km 53.300 (Design Chainage) in the State of Chhattisgarh under BharatMala on Hybrid Annuity Mode.
Providing and placing concrete work including cost of machinery & equipment,
manpower, materials, admixtures and consumables including staging &
scaffolding, handling & transportation, batching, mixing, transportation of
concrete, placing, vibrating to achieve compaction and curing, etc. at all
elevations for :
Reinforced cement Concrete grade conforming to IS:456 with coarse sand and
8.07 graded hard stone aggregate 20 mm and down nominal size machine mixed at -
all heights / depths any shape, any position, thickness, including addition of
suitable plasticizer/ super plasticizer conforming to IS:9103 to achieve required
slump in concrete, . Preparation of top surface or chipping to receive grouting
including formwork, scaffolding & staging, materials, manpower, Tools &
tackles, Consumables etc. but excluding Reinforcement Steel all complete as
per approved drawing, Technical specification, MoRTH specification and as
directed by Engineer In-charge.
Providing and placing concrete work including cost of machinery & equipment,
manpower, materials, admixtures and consumables including staging &
scaffolding, handling & transportation, batching, mixing, transportation of
concrete, placing, vibrating to achieve compaction and curing, etc. at all
elevations for :
Reinforced cement Concrete grade conforming to IS:456 with coarse sand and
8.09 graded hard stone aggregate 20 mm and down nominal size machine mixed at -
all heights / depths any shape, any position, thickness, including addition of
suitable plasticizer/ super plasticizer conforming to IS:9103 to achieve required
slump in concrete, . Preparation of top surface or chipping to receive grouting
including formwork, scaffolding & staging, materials, manpower, Tools &
tackles, Consumables etc. but excluding Reinforcement Steel & Prestressing
activities all complete as per approved drawing, Technical specification, MoRTH
specification and as directed by Engineer In-charge.
Note : The item rate shall include all charges for Girder loading, transportation,
unloading, launching, placing etc. complete including cost of crane, trailer & all
other equipments.
a) in RC Slab, Pedestals - M45 Cu.m. 3,970 5,202.00 20,651,940.00
in PSC (Pre Stressed Concrete) I Girders - M-45 Grade Cu.m. 5,676 6,876.00 39,028,176.00
c) in PSC I Girders Cu.m. - -
Providing, Straightening, cutting, bending, placing in position at any elevation,
binding & fixing in position using 18/ 20 SWG annealed iron wires including
supplying binding wires, providing cover blocks, shifting, all materials,
manpower, Tools & tackles, Consumables etc. all complete as per approved
drawing, Technical specification, MoRTH specification and as directed by
Engineer In-charge.
8.10 -
- High yield strength deformed bars conforming to grade Fe 415/ Fe 500/ Fe 500
D of IS : 1786
Providing and laying Tack coat and 50mm thick Bituminous Concrete (BC)
wearing course over Deck Slab using VG40 grade bitumen with 100-120 TPH
batch type hot mix plant producing an average output of 75 tonnes per hour
using crushed aggregates of specified grading, premixed with bituminous binder
as per approved mix design with minimum bitumen @ 5.5 % of mix and filler, Emulsion shall be in Bidder
8.12
transporting the hot mix to work site, laying with a hydrostatic paver finisher
sqm 16,362 255.00 4,172,310.00
scope
with sensor control to the required grade, level and alignment, rolling with
smooth wheeled, vibratory and tandem rollers to achieve the desired
compaction complete in all respects as per drawing and Technical Specifications
& MORTH specification clause No. 507 & 501.
Providing and fixing GI drainage spouts with 150mm dia outlet embedded in
8.13 concrete as per approved drawing,Technical Specifications & MoRTH Clause Nr. 152 1,116.00 169,632.00
2705 as directed by Engineer In-charge.
Supplying and fixing of bearings complete as per drawings and Technical
8.14
Specifications Section 2000 and IRC:83.
-
Elastomeric bearing cucm - -
Supplying and fixing of bearings complete as per drawings, Technical
8.15
Specifications clause 2000 and IRC:83 (Part III) - 2002
-
All types of POT-PTFE Bearings - as per approved drawings and capacity as per
a)
Design requirements
No's 210 37,200.00 7,812,000.00
8.16 Expansion Joints -
Asphaltic Plug Expansion joint
Providing and laying of asphaltic plug joint to provide for horizontal movement
of 25 mm and vertical movement of 2 mm, depth of joint varying from 75 mm
to 100 mm, width varying from 500 mm to 750 mm (in traffic direction),
Cement shall be in Bidder
a) covered with a closure plate of 200mm x 6mm of wieldable structural steel Rmtr 149 9,300.00 1,385,700.00
conforming to IS: 2062, asphaltic plug to consist of polymer modified bitumen scope
binder, carefully selected single size aggregate of 12.5 mm nominal size and a
heat resistant foam caulking/backer rod, all as per approved drawings,
technical specifications & MoRTH
Page 11 of 24
Four lane with Paved shoulder configuration of Bilaspur- Pathrapali Section of NH- 111 (New NH-130) from Km 0.000 (Design Chainage) to
Km 53.300 (Design Chainage) in the State of Chhattisgarh under BharatMala on Hybrid Annuity Mode.
Strip seal jt. in PSC Girder catering to maximum horizontal movement upto 70
mm
Providing and placing concrete work including cost of machinery & equipment,
manpower, materials, admixtures and consumables including staging &
scaffolding, handling & transportation, batching, mixing, transportation of
concrete, placing, vibrating to achieve compaction and curing, etc. at all
elevations for :
Providing and laying stone boulder pitching on slopes and for floor aprons
including excavation, surface dressing, levelling course, boulder placing,
8.19
pointing etc complete as per drawings and Technical Specifications Section
cum - -
2500 of MoRTH.
Providing weep holes in abutments, wing walls, retaining walls, return walls, box
structures etc. with 100 mm dia AC/ PVC/ HDPE pipes complete as per approved
8.20
drawing, Technical specification, MoRTH specification 2706 and as directed by
Nr. - -
Engineer In-charge.
Painting with synthetic enamel of Bridge no. and span arrangement as per
8.21
drawing, IRC:7-1971 and directions of the Engineer Nr. 8 279.00 2,232.00
Design, Supply, fabrication, painting/ Metalizing, bolting, erection etc. complete All the materials shall be in
composite girder for Central Span of ROB as per IRS B1-2001, RDSO BS bidder scope, Complete design
110, BS 111 including preparation & approval thereof from Railway authority for
and Railway liasioning also in
8.22 QAP, CRS, launching scheme etc. complete including co-ordination with railway MT 344 73,550.00 25,301,200.00
authorities, getting blocks, launching cranes etc. complete as per approved Bidder scope & Cement for
drawing, Technical specification, MoRTH specification and as directed by grouiting shall be in bidder
Engineer In-charge. scope
Providing, laying, fixing PVC pipe of approved quality in footpath kerb, crash
barrier, Rain water downtake pipes, toll booth island including all specials &
8.23
accessories all complete as per approved drawing as directed by Engineer In-
-
charge
b) 150 mm dia m 2,452 279.00 684,108.00
Supplying and providing two coats of synthetic enamel paint of asian paint or
equivalent to give an even shade applied to concrete surfaces of parapet/ crash
barrier, kerb etc. at various elevations including surface preparation, cracks/ pin
8.24 hole fillings etc & one coat of primer all of approved shade and quality complete sqm 6,573 167.00 1,097,691.00
to the satisfaction with all material, labour, staging, scaffolding etc. complete
as per approved drawing, Technical specification, MoRTH specification and as
directed by Engineer In-charge.
Providing and laying boulder apron including excavation, surface dressing,
8.25 levelling course, boulder placing, pointing etc complete as per drawings and cum - -
Technical Specifications Section 2500 of MoRTH.
Providing and fixing Tar Paper Bearing complete as per drawing and IRC:SP:13-
8.26
2004.
sqm 46 1,023.00 47,058.00
Providing and filling joint sealing compound in approach slab complete as per
8.27
Technical Specifications and drawing.
m - -
Providing Bored cast-in-situ M35 grade R.C.C. Pile in all types of soil
including soft rock (1200 dia) incl cost of all materials, labour, loading,
8.28
unloading, lead upto 5 km, curing, hire charges tech spec: 1100,1600,1700
m - -
excluding Reinforcement
Plain / Reinforced Cement Concrete M35 in pile caps complete as per drawing
8.29
and technical specification 1500, 1700, 2200.
Cum - -
Providing, cutting, bending and fixing in position of TMT bar reinforcement in
8.30
piles and pile caps structures complete as per Tech. Spec. Cl 1600
MT - -
8.31 Providing and laying MS Steel Liner for Piles (6mm thick) MT - -
8.32 Conducting Load Tests on Piles -
a) Initial Load Test on Pile -
Vertical load test MT - -
Horizontal load test MT - -
b) Routine Load Test on Pile -
Vertical load test MT - -
Horizontal load test MT - -
Box Pushing for RUB of size 36m (L) x 12m (W) x 4.5m (H). Concrete,
8.33 Reinforcement shall be measured & paid separately under item sr. no. 6.06 & No. 2 - -
6.10
RE-Walls -
Page 12 of 24
Four lane with Paved shoulder configuration of Bilaspur- Pathrapali Section of NH- 111 (New NH-130) from Km 0.000 (Design Chainage) to
Km 53.300 (Design Chainage) in the State of Chhattisgarh under BharatMala on Hybrid Annuity Mode.
Design, Supply and erection of M-35 grade RCC facia panels including
reinforcement and reinforcing elements with all fixtures and accessories
complete
All charges for construction of reinforced earth wall by providing the design
including design calculations, technical specifications, drawings & detailed work
methodology and getting it approved from Engineer / Client / Authority. Supply
of geogrid and other required accessories like panel casting moulds, HDPE Complete Geogrid,
connectors, geo-textile, bearing pads etc. at site. Casting of panels including
geocomposite, other materials
8.33 tying of HYSD reinforcement including cost of M-35 Grade concrete & sqm 83,856 2,332.00 195,552,192.00
reinforcement steel, curing & stacking of panels at yard, loading & required for RE Wall shall be in
transportation of panels to the erection site, unloading & stacking of panels at bidder scope
erection site, shifting & erecting panels, transporting & fixing of geogrid at
erection site including all accessories, coping beam etc. Supervision of all
activities involved in RE wall construction, providing 20 years guarantee in
format approved by Engineer / Client / Authority. All work shall be carried out as
per approved design & drawing/s, MoRT&H specification (latest revision),
supplementary technical specifications, addendum and instructions of Engineer
In-charge.
Providing and placing concrete work including cost of machinery & equipment,
manpower, materials, admixtures and consumables including staging &
scaffolding, handling & transportation, batching, mixing, transportation of
concrete, placing, vibrating to achieve compaction and curing, etc. at all
elevations for :
8.34 cum 1,887 2,640.00 4,981,680.00
M-20 Grade Plain Cement Concrete (PCC) as levelling course below facia panel
for RE Wall etc. including preparation of bottom surface, compaction, formwork,
scaffolding & staging, materials, manpower, Tools & tackles, Consumables etc.
all complete as per approved drawing, Technical specification, MoRTH
specification and as directed by Engineer In-charge.
Providing & Laying Geocomosite Drain as filter media behind reinforced earth
8.35 facia panel as per approved design, drawings, Technical Specifications and as sqm 83,856 300.00 25,156,800.00
directed by Engineer In-charge.
Providing & Filling in RE Wall area with selected soil meeting approved design
parameters in layers in soil reinforced zone obtained from borrow pits with all
8.36 lifts and leads, transporting to site, spreading, grading to required slope and cum 1,027,198 250.00 256,799,475.00
compaction as per approved drawing, Technical Specifications & MoRTH Cls No.
3104 and as directed by Engineer In-charge.
Providing and constructing Reinforced Cement Concrete Crash Barrier in M-40
grade including, shuttering, scaffolding, staging etc. complete excluding
8.37 reinforcement as per approved drawings and Technical Specifications & MoRTH Cum 6,289.20 5,792.00 36,427,046.40
Sections 809, 811, 1000, 1500, 1600, 1700 and as directed by Engineer In-
Charge.
Providing and placing concrete work including cost of machinery & equipment,
manpower, materials, admixtures and consumables including staging &
scaffolding, handling & transportation, batching, mixing, transportation of
concrete, placing, vibrating to achieve compaction and curing, etc. at all
elevations for :
Providing, laying, fixing PVC pipe of approved quality in footpath kerb, crash
barrier, Rain water downtake pipes, toll booth island including all specials &
accessories all complete as per approved drawing as directed by Engineer In-
8.40
charge
m 3,494 279.00 974,826.00
- 150 mm dia.
Bill No. 9 : DRAINAGE AND PROTECTION WORKS -
Construction of 300 mm wide drainage chutes in cement concrete M-20 grade
with foundations in M-15 grade concrete including construction of bell mouth at
9.02
entry as per drawings and Technical Specifications Sections 1500 and 1700 and
-
Additional Technical Specification A-15.
Providing and placing concrete work including cost of machinery & equipment,
manpower, materials, admixtures and consumables including staging &
scaffolding, handling & transportation, batching, mixing, transportation of
concrete, placing, vibrating to achieve compaction and curing, etc. at all
elevations for :
a)
M-15 Grade Plain Cement Concrete (PCC) as levelling course/ fill around
cum 90 2,655.00 238,950.00
foundations, pipes, floors on grade, water retaining structures, equipment
foundations, under foundations etc. including formwork, scaffolding & staging,
materials, manpower, Tools & tackles, Consumables etc. all complete as per
approved drawing, Technical specification, MoRTH specification and as directed
by Engineer In-charge.
Providing and placing concrete work including cost of machinery & equipment,
manpower, materials, admixtures and consumables including staging &
scaffolding, handling & transportation, batching, mixing, transportation of
concrete, placing, vibrating to achieve compaction and curing, etc. at all
elevations for :
M-20 Grade Plain Cement Concrete (PCC) as levelling course/ fill around
b)
foundations, pipes, floors on grade, water retaining structures, equipment
cum 90 2,826.00 254,340.00
foundations, under foundations etc. including formwork, scaffolding & staging,
materials, manpower, Tools & tackles, Consumables etc. all complete as per
approved drawing, Technical specification, MoRTH specification and as directed
by Engineer In-charge.
Page 13 of 24
Four lane with Paved shoulder configuration of Bilaspur- Pathrapali Section of NH- 111 (New NH-130) from Km 0.000 (Design Chainage) to
Km 53.300 (Design Chainage) in the State of Chhattisgarh under BharatMala on Hybrid Annuity Mode.
Providing and placing concrete work including cost of machinery & equipment,
manpower, materials, admixtures and consumables including staging &
scaffolding, handling & transportation, batching, mixing, transportation of
concrete, placing, vibrating to achieve compaction and curing, etc. at all
elevations for :
M-20 Grade Plain Cement Concrete (PCC) as levelling course/ fill around
c)
foundations, pipes, floors on grade, water retaining structures, equipment
cum 83 3,105.00 257,715.00
foundations, under foundations etc. including formwork, scaffolding & staging,
materials, manpower, Tools & tackles, Consumables etc. all complete as per
approved drawing, Technical specification, MoRTH specification and as directed
by Engineer In-charge.
Providing & Laying filter media with stone crushed aggregates underneath stone
boulder pitching on slopes with well packed material to specified thickness &
9.04
gradation complete with all leads and lifts as per approved drawings, Technical
cum 4,619 1,400.00 6,466,600.00
Specifications, MoRTH specifications and as directed by Engineer In-charge.
Constructing unlined surface drains of average cross sectional area 0.5 sqm in
soil to specified lines, grade, levels and dimensions including setting out,
clearing & grubbing, removal of debris, dressing the sides, levelling to grade
9.05 and disposal of all unsuitable materials and transportation & dumping of all cum 13,087 465.00 6,085,455.00
suitable material at embankment/ subgrade/ Median Filling location with all lifts
and leads complete as per approved drawing, Technical specification, MoRTH
specification cls no. 301 & 309 and as directed by Engineer In-charge.
- All types of soils including, laterite, morrum which can be excavated by means
of mechanical excavator and/or manual (but does not require crow bar, pick axe,
chiselling or blasting)
Providing and placing concrete work including cost of machinery & equipment,
manpower, materials, admixtures and consumables including staging &
scaffolding, handling & transportation, batching, mixing, transportation of
concrete, placing, vibrating to achieve compaction and curing, etc. at all
elevations for :
(b)
M-15 Grade Plain Cement Concrete (PCC) as levelling course/ fill around
cum 530 2,655.00 1,407,042.14
foundations, pipes, floors on grade, water retaining structures, equipment
foundations, under foundations etc. including formwork, scaffolding & staging,
materials, manpower, Tools & tackles, Consumables etc. all complete as per
approved drawing, Technical specification, MoRTH specification and as directed
by Engineer In-charge.
Providing and placing concrete work including cost of machinery & equipment,
manpower, materials, admixtures and consumables including staging &
scaffolding, handling & transportation, batching, mixing, transportation of
concrete, placing, vibrating to achieve compaction and curing, etc. at all
elevations for :
Providing covered RCC drain in urban areas including excavation as 'per drawing
9.10
and Technical Specifications Sections 1500, 1600 and '1700 as per cross section
-
Page 14 of 24
Four lane with Paved shoulder configuration of Bilaspur- Pathrapali Section of NH- 111 (New NH-130) from Km 0.000 (Design Chainage) to
Km 53.300 (Design Chainage) in the State of Chhattisgarh under BharatMala on Hybrid Annuity Mode.
- All types of soils including, laterite, morrum which can be excavated by means
of mechanical excavator and/or manual (but does not require crow bar, pick axe,
chiselling or blasting)
Providing and placing concrete work including cost of machinery & equipment,
manpower, materials, admixtures and consumables including staging &
scaffolding, handling & transportation, batching, mixing, transportation of
concrete, placing, vibrating to achieve compaction and curing, etc. at all
elevations for :
M-15 Grade Plain Cement Concrete (PCC) as levelling course/ fill around
Cum 3,648 2,655.00 9,684,165.60
foundations, pipes, floors on grade, water retaining structures, equipment
foundations, under foundations etc. including formwork, scaffolding & staging,
materials, manpower, Tools & tackles, Consumables etc. all complete as per
approved drawing, Technical specification, MoRTH specification and as directed
by Engineer In-charge.
Providing and placing concrete work including cost of machinery & equipment,
manpower, materials, admixtures and consumables including staging &
scaffolding, handling & transportation, batching, mixing, transportation of
concrete, placing, vibrating to achieve compaction and curing, etc. at all
elevations for :
Providing and placing concrete work including cost of machinery & equipment,
manpower, materials, admixtures and consumables including staging &
scaffolding, handling & transportation, batching, mixing, transportation of
concrete, placing, vibrating to achieve compaction and curing, etc. at all
elevations for :
Page 15 of 24
Four lane with Paved shoulder configuration of Bilaspur- Pathrapali Section of NH- 111 (New NH-130) from Km 0.000 (Design Chainage) to
Km 53.300 (Design Chainage) in the State of Chhattisgarh under BharatMala on Hybrid Annuity Mode.
Providing and laying of a reinforced cement concrete NP-4 pipe duct.300mm dia
across the road extending from drain to drain in cuts and toe of slope to toe of
slope in fills, constructing head walls at both the ends, providing a minimum fill
Cement shall be in Bidder
9.14 of granular material over top and side of RCC pipe as per IRC:98-1997, bedded Rm 1,800 1,800.00 3,240,000.00
on a 0.3m thick layer of granular material including excavation & backfilling as scope
per approved drawing, Technical specification, MoRTH specification and as
directed by Engineer In-charge.
Providing and fixing 1.2meters high MS Pedestrian Guard rails embedded in
cement concrete, including cost of all civil works, fabrication, erection/
installation, bolting, painting including surface preparation etc. complete
9.15
including cost of all materials, labour, loading and unloading, etc. complete as
-
per approved drawing, Technical specification, MoRTH specification, Cls. no.
6.1.9 of IRC 103 latest revision and as directed by Engineer In-charge.
Page 16 of 24
Four lane with Paved shoulder configuration of Bilaspur- Pathrapali Section of NH- 111 (New NH-130) from Km 0.000 (Design Chainage) to
Km 53.300 (Design Chainage) in the State of Chhattisgarh under BharatMala on Hybrid Annuity Mode.
Flexible Crash Barrier, Wire Rope Safety Barrier (Providing and erecting a wire
rope safety barrier with vertical posts of medium weight RS Joist (ISMB series)
100 mm x 75 mm (11.50 kg/m), 1.50 m long 0.85 m above ground and 0.65 m
below ground level, split at the bottom for better grip, embedded in M 15 grade
cement concrete 450 x 450 x 450 mm, 1.50 m centre to centre and with 4
horizontal steel wire rope 40 mm dia and anchored at terminal posts 15 m
10.11 apart. Terminal post to be embedded in M 15 Rm - -
gradecementconcretefoundation2400 x 450 x 900 mm (depth), strengthened by
a strut of RS joist 100 x 75 mm, 2 m long at 450 inclination and a tie 100 x 8
mm, 1.50 m long at the bottom, all embedded in foundation concrete as per
approved design and drawing, rate including all civil works like excavation and
cement concrete, retroreflective stickers etc. complete as per approved drawing
& as directed by Engineer In-Charge.
Providing and fixing RCC M 20 guard posts along road side, size250 mm dia, 600
mm high, above road level, 300 mm below road level, embedded in Cement
10.12 Concrete of size 500 mm x 500 mm x 400 mm all complete as per approved Nr. - -
drawing, Technical specification, MoRTH specification and as directed by
Engineer In-charge.
Providing & construction of Cast in Situ Cement Concrete M20 kerb
(Construction of cement concrete kerb with top and bottom width 115 and 165
mm respectively, having height as per approved drawing in M 20 grade laid with
10.13
kerb laying machine including cutting for expansion joint, curing etc complete
Rm 52,554 195.00 10,248,030.00
as per approved drawing, Technical specification, MoRTH specification and as
directed by Engineer In-charge.
Providing & construction of Cast in Situ Cement Concrete M20 kerb
(Construction of cement concrete kerb with top and bottom width 115 and 165
mm respectively, having height as per approved drawing in M 20 grade laid with
10.14
kerb laying machine including cutting for expansion joint, curing etc complete -
as per approved drawing, Technical specification, MoRTH specification and as
directed by Engineer In-charge.
Providing and placing concrete work including cost of machinery & equipment,
manpower, materials, admixtures and consumables including staging &
scaffolding, handling & transportation, batching, mixing, transportation of
concrete, placing, vibrating to achieve compaction and curing, etc. at all
elevations for :
a)
M-15 Grade Plain Cement Concrete (PCC) as levelling course/ fill around
cum - -
foundations, pipes, floors on grade, water retaining structures, equipment
foundations, under foundations etc. including formwork, scaffolding & staging,
materials, manpower, Tools & tackles, Consumables etc. all complete as per
approved drawing, Technical specification, MoRTH specification and as directed
by Engineer In-charge.
Page 17 of 24
Four lane with Paved shoulder configuration of Bilaspur- Pathrapali Section of NH- 111 (New NH-130) from Km 0.000 (Design Chainage) to
Km 53.300 (Design Chainage) in the State of Chhattisgarh under BharatMala on Hybrid Annuity Mode.
- All types of soils including, laterite, morrum which can be excavated by means
of mechanical excavator and/or manual (but does not require crow bar, pick axe,
chiselling or blasting)
- With material prepared by mixing mechanically using mix in place method with
rotavator or using Batching Plant at Optimum Moisture Content (OMC).
Providing, laying, spreading and compacting graded stone aggregate to Wet Mix
Macadam specification as per the Clause No. 406 of MoRTH including premixing
the Material with water at OMC in mechanical mix plant carriage of mixed
Material by tipper to site, laying in uniform layers with sensor paver in sub- base
11.06
/ base course on well prepared surface and compacting with vibratory roller to
Cu.m. - -
achieve the desired density including all machinery, manpower, tools & tackles,
fuel, consumables etc. complete as per approved drawing, Technical
specification, MoRTH specification and as directed by Engineer In-charge.
Providing and applying primer coat using bitumen emulsion at the rate of 0.60
to 0.90 kg/ sqm on prepared surface of granular base including clearing of road
surface using mechanical means/ mechanical broom and spraying with emulsion
11.07 pressure distributor etc. complete including all machinery, manpower, tools & Sqm - -
tackles, fuel, consumables etc. complete as per approved Drawings, Technical
Specifications & standard MoRTH specifications of clause 502 and instruction of
Engineer in Charge.
Providing and applying tack coat using bitumen emulsion at the rate of 0.225
kg/ sqm for bituminous surface and 0.25 kg/ sqm for granular surface on
prepared surface including cleaning of road surface using mechanical means/
11.08
mechanical broom and spraying with emulsion pressure distributor etc.
-
complete including all machinery, manpower, tools & tackles, fuel, consumables
etc. complete as per approved Drawings, Technical Specifications & standard
MoRTH specifications of clause 503 and instruction of Engineer in Charge.
Providing and laying Bituminous Concrete (BC) wearing course using VG40
grade bitumen with 100-120 TPH batch type hot mix plant producing an average
output of 75 tonnes per hour using crushed aggregates of specified grading,
premixed with bituminous binder as per approved mix design with minimum
11.11 bitumen @ 5.5 % of mix and filler, transporting the hot mix to work site, laying cum - -
with a hydrostatic paver finisher with sensor control to the required grade, level
and alignment, rolling with smooth wheeled, vibratory and tandem rollers to
achieve the desired compaction complete in all respects as per drawing and
Technical Specifications & MORTH specification clause No. 507 & 501.
Page 18 of 24
Four lane with Paved shoulder configuration of Bilaspur- Pathrapali Section of NH- 111 (New NH-130) from Km 0.000 (Design Chainage) to
Km 53.300 (Design Chainage) in the State of Chhattisgarh under BharatMala on Hybrid Annuity Mode.
Providing, laying and jointing RCC NP- 4 Pipe (as per IS:458 latest) for culverts
including testing including fixing collar with cement mortar 1:2 but excluding
11.33 excavation, protection works, backfilling, concrete and masonry works in head Rm - -
walls and parapets as per approved drawing, Technical specification, MoRTH
specification and as directed by Engineer In-charge.
Providing RCC drain having internal dimension of 1500mm (W) X 1500 mm (D)
including excavation, backfilling, levelling course of PCC M-15 grade, walls, raft
& cover slab of RCC M-25 grade including reinforcement including disposal of all
11.34 unsuitable materials and transportation & dumping of all suitable material at Rm - -
embankment/ subgrade/ Median Filling location with all lifts and leads etc.
complete as per approved drawing, Technical specification, MoRTH specification
and as directed by Engineer In-charge.
Construction of dry lean cement concrete Sub- base over a prepared sub-grade
with coarse and fine aggregate conforming to IS: 383, the size of coarse
aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1,
aggregate gradation after blending to be as per table 600-1, cement content not
to be less than 150 kg/ cum, optimum moisture content to be determined during
4A1
trial length construction, concrete strength not to be less than 10 Mpa at 7 days,
cum 2,174 557.00 1,210,918.00
mixed in a batching plant, transported to site, laid with a paver with electronic
sensor, compacting with 8-10 tonnes vibratory roller, finishing and curing
complete as per approved Drawing, Technical Specifications and MoRTH clause
no. 601 as directed by Engineer In-Charge.
Page 19 of 24
Four lane with Paved shoulder configuration of Bilaspur- Pathrapali Section of NH- 111 (New NH-130) from Km 0.000 (Design Chainage) to
Km 53.300 (Design Chainage) in the State of Chhattisgarh under BharatMala on Hybrid Annuity Mode.
- All types of soils including, laterite, morrum which can be excavated by means
of mechanical excavator and/or manual (but does not require crow bar, pick axe,
chiselling or blasting)
- With material prepared by mixing mechanically using mix in place method with
rotavator or using Batching Plant at Optimum Moisture Content (OMC).
Providing, laying, spreading and compacting graded stone aggregate to Wet Mix
Macadam specification as per the Clause No. 406 of MoRTH including premixing
the Material with water at OMC in mechanical mix plant carriage of mixed
Material by tipper to site, laying in uniform layers with sensor paver in sub- base
14.06
/ base course on well prepared surface and compacting with vibratory roller to
Cu.m. - -
achieve the desired density including all machinery, manpower, tools & tackles,
fuel, consumables etc. complete as per approved drawing, Technical
specification, MoRTH specification and as directed by Engineer In-charge.
Providing and applying primer coat using bitumen emulsion at the rate of 0.60
to 0.90 kg/ sqm on prepared surface of granular base including clearing of road
surface using mechanical means/ mechanical broom and spraying with emulsion
14.07 pressure distributor etc. complete including all machinery, manpower, tools & Sqm - -
tackles, fuel, consumables etc. complete as per approved Drawings, Technical
Specifications & standard MoRTH specifications of clause 502 and instruction of
Engineer in Charge.
Providing and applying tack coat using bitumen emulsion at the rate of 0.225
kg/ sqm for bituminous surface and 0.25 kg/ sqm for granular surface on
prepared surface including cleaning of road surface using mechanical means/
14.08
mechanical broom and spraying with emulsion pressure distributor etc.
-
complete including all machinery, manpower, tools & tackles, fuel, consumables
etc. complete as per approved Drawings, Technical Specifications & standard
MoRTH specifications of clause 503 and instruction of Engineer in Charge.
Providing and laying Bituminous Concrete (BC) wearing course using VG40
grade bitumen with 100-120 TPH batch type hot mix plant producing an average
output of 75 tonnes per hour using crushed aggregates of specified grading,
premixed with bituminous binder as per approved mix design with minimum
14.11 bitumen @ 5.5 % of mix and filler, transporting the hot mix to work site, laying Cu.m. - -
with a hydrostatic paver finisher with sensor control to the required grade, level
and alignment, rolling with smooth wheeled, vibratory and tandem rollers to
achieve the desired compaction complete in all respects as per drawing and
Technical Specifications & MORTH specification clause No. 507 & 501.
Construction of dry lean cement concrete Sub- base over a prepared sub-grade
with coarse and fine aggregate conforming to IS: 383, the size of coarse
aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1,
aggregate gradation after blending to be as per table 600-1, cement content not
to be less than 150 kg/ cum, optimum moisture content to be determined during
14.12
trial length construction, concrete strength not to be less than 10 Mpa at 7 days,
Cu.m. - -
mixed in a batching plant, transported to site, laid with a paver with electronic
sensor, compacting with 8-10 tonnes vibratory roller, finishing and curing
complete as per approved Drawing, Technical Specifications and MoRTH clause
no. 601 as directed by Engineer In-Charge.
Page 20 of 24
Four lane with Paved shoulder configuration of Bilaspur- Pathrapali Section of NH- 111 (New NH-130) from Km 0.000 (Design Chainage) to
Km 53.300 (Design Chainage) in the State of Chhattisgarh under BharatMala on Hybrid Annuity Mode.
Providing and placing concrete work including cost of machinery & equipment,
manpower, materials, admixtures and consumables including staging &
scaffolding, handling & transportation, batching, mixing, transportation of
concrete, placing, vibrating to achieve compaction and curing, etc. at all
elevations for :
M-15 Grade Plain Cement Concrete (PCC) as levelling course/ fill around Cu.m. - -
14.24
foundations, pipes, floors on grade, water retaining structures, equipment
foundations, under foundations etc. including formwork, scaffolding & staging,
materials, manpower, Tools & tackles, Consumables etc. all complete as per
approved drawing, Technical specification, MoRTH specification and as directed
by Engineer In-charge.
Providing and placing concrete work including cost of machinery & equipment,
manpower, materials, admixtures and consumables including staging &
scaffolding, handling & transportation, batching, mixing, transportation of
concrete, placing, vibrating to achieve compaction and curing, etc. at all
elevations for :
Page 21 of 24
Four lane with Paved shoulder configuration of Bilaspur- Pathrapali Section of NH- 111 (New NH-130) from Km 0.000 (Design Chainage) to
Km 53.300 (Design Chainage) in the State of Chhattisgarh under BharatMala on Hybrid Annuity Mode.
Providing and installing canopy for toll plaza including civil works like
excavation, concreting, reinforcement, backfilling, canopy structure including
columns, truss, perline, rafter, sheeting, fabrication, erection, bolting, Gutter,
14.29
Rain water downtake pipes upto ground drainage, painting etc. all complete
Sqm - -
including design & approval from competent authority as directed by Project
Manager.
Providing & constructing Toilet Block with proper partition for Ladies & Gents
including all civil, architectural, electrical work upto main panel, plumbing,
Plumbing accessories, sanitary ware, Doors and Windows, Iron Grill Safety for
14.30
Windows, Tiles Flooring, Dado, Painting, water tank, septic tank, borewell, in
Sqm - -
lock & key conditions, weathering Course etc. complete as per approved
Drawing or Directed by Engineer In charge.
Providing RCC drain having internal dimension of 1200mm (W) X 1500 mm (D)
including excavation, backfilling, levelling course of PCC M-15 grade, walls, raft
& cover slab of RCC M-25 grade including reinforcement including disposal of all
14.31 unsuitable materials and transportation & dumping of all suitable material at Rm - -
embankment/ subgrade/ Median Filling location with all lifts and leads etc.
complete as per approved drawing, Technical specification, MoRTH specification
and as directed by Engineer In-charge.
Providing, laying, fixing PVC pipe of approved quality in footpath kerb, crash
barrier, Rain water downtake pipes, toll booth island including all specials &
accessories all complete as per approved drawing as directed by Engineer In-
14.32
charge
Lm - -
- 150 mm dia.
14.33 Providing and fixing Hazard marker No.'s - -
Supply and fixing of Full width overhead gantry at Toll Plaza/ other
location and signs including entire scope like civil work, fabrication work,
14.34 erection work, signages etc complete in all respect in line with typical drawing Nos. - -
attached and as per approved drawing, Technical specification, MoRTH
specification and as directed by Engineer In-charge.
14.35 Informatory Signs Sqm. - -
14.36 Red Reflector Signs Nos. - -
14.37 Mandatory (Stop) Sign Nos. - -
Providing, laying & maintenance of the live sods of perennial turf forming grass
on embankment slope, verges or other locations shown on the drawing or as
directed by the engineer including preparation of ground, fetching of sods and
14.38
watering & maintaining for 1 year beyond COD as per approved drawing,
Sqm - -
Technical specification, MoRTH specification and as directed by Engineer In-
charge.
Providing and constructing Reinforced Cement Concrete New Jercy Type
Crash Barrier in M-40 grade including, shuttering, scaffolding, staging etc.
complete including cost of PVC Duct but excluding reinforcement as per
14.39
approved drawings and Technical Specifications & MoRTH Sections 809, 811,
Cum - -
1000, 1500, 1600, 1700 and as directed by Engineer In-Charge.
Construction of Tunnel
Construction of underground RCC Tunnel connecting to all Toll Booths with
Administrative Building of internal dimensions of minimum 3m (W) x 2.5m (H)
14.41 including all civil works like, excavation, backfilling, RCC, shuttering, Rm - -
reinforcement, waterproofing, plastering, painting, electrification, ventilation
staircase etc complete as per approved drawing, Technical specification, MoRTH
specification and as directed by Engineer In-charge.
Bill 15: MAJOR AND MINOR JUNCTIONS -
Clearing and grubbing road land by mechanical means including uprooting rank
vegetation, grass, bushes, shrubs and trees girth upto 300mm, removal of
15.00 stumps of trees cut earlier, disposal of unusable materials and stacking of Hect. - -
usable material to be used or auctioned, with all leads and lifts as per Technical
Specifications Clause 201.
- All types of soils including, laterite, morrum which can be excavated by means
of mechanical excavator and/or manual (but does not require crow bar, pick axe,
chiselling or blasting)
- With material prepared by mixing mechanically using mix in place method with
rotavator or using Batching Plant at Optimum Moisture Content (OMC).
Page 22 of 24
Four lane with Paved shoulder configuration of Bilaspur- Pathrapali Section of NH- 111 (New NH-130) from Km 0.000 (Design Chainage) to
Km 53.300 (Design Chainage) in the State of Chhattisgarh under BharatMala on Hybrid Annuity Mode.
Providing, laying, spreading and compacting graded stone aggregate to Wet Mix
Macadam specification as per the Clause No. 406 of MoRTH including premixing
the Material with water at OMC in mechanical mix plant carriage of mixed
Material by tipper to site, laying in uniform layers with sensor paver in sub- base
15.06
/ base course on well prepared surface and compacting with vibratory roller to
cum 3,437 1,500.00 5,155,965.00
achieve the desired density including all machinery, manpower, tools & tackles,
fuel, consumables etc. complete as per approved drawing, Technical
specification, MoRTH specification and as directed by Engineer In-charge.
Providing and applying primer coat using bitumen emulsion at the rate of 0.60
to 0.90 kg/ sqm on prepared surface of granular base including clearing of road
surface using mechanical means/ mechanical broom and spraying with emulsion
Emulsion shall be in Bidder
15.07 pressure distributor etc. complete including all machinery, manpower, tools & sqm 13,749 26.00 357,479.98
tackles, fuel, consumables etc. complete as per approved Drawings, Technical scope
Specifications & standard MoRTH specifications of clause 502 and instruction of
Engineer in Charge.
Providing and applying tack coat using bitumen emulsion at the rate of 0.225
kg/ sqm for bituminous surface and 0.25 kg/ sqm for granular surface on
prepared surface including cleaning of road surface using mechanical means/ Emulsion shall be in Bidder
15.08
mechanical broom and spraying with emulsion pressure distributor etc.
sqm 13,749 15.00 206,238.45
scope
complete including all machinery, manpower, tools & tackles, fuel, consumables
etc. complete as per approved Drawings, Technical Specifications & standard
MoRTH specifications of clause 503 and instruction of Engineer in Charge.
Providing and laying Bituminous Concrete (BC) wearing course using VG40
grade bitumen with 100-120 TPH batch type hot mix plant producing an average
output of 75 tonnes per hour using crushed aggregates of specified grading,
premixed with bituminous binder as per approved mix design with minimum
Filler Material shall be in
15.10 bitumen @ 5.5 % of mix and filler, transporting the hot mix to work site, laying cum 550 3,833.00 2,108,035.01
with a hydrostatic paver finisher with sensor control to the required grade, level Bidder scope
and alignment, rolling with smooth wheeled, vibratory and tandem rollers to
achieve the desired compaction complete in all respects as per drawing and
Technical Specifications & MORTH specification clause No. 507 & 501.
Construction of dry lean cement concrete Sub- base over a prepared sub-grade
with coarse and fine aggregate conforming to IS: 383, the size of coarse
aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1,
aggregate gradation after blending to be as per table 600-1, cement content not
to be less than 150 kg/ cum, optimum moisture content to be determined during
15.11
trial length construction, concrete strength not to be less than 10 Mpa at 7 days,
cum - -
mixed in a batching plant, transported to site, laid with a paver with electronic
sensor, compacting with 8-10 tonnes vibratory roller, finishing and curing
complete as per approved Drawing, Technical Specifications and MoRTH clause
no. 601 as directed by Engineer In-Charge.
Providing and placing concrete work including cost of machinery & equipment,
manpower, materials, admixtures and consumables including staging &
scaffolding, handling & transportation, batching, mixing, transportation of
concrete, placing, vibrating to achieve compaction and curing, etc. at all
elevations for :
15.13
M-15 Grade Plain Cement Concrete (PCC) as levelling course/ fill around
cum 239 3,627.00 867,324.51
foundations, pipes, floors on grade, water retaining structures, equipment
foundations, under foundations etc. including formwork, scaffolding & staging,
materials, manpower, Tools & tackles, Consumables etc. all complete as per
approved drawing, Technical specification, MoRTH specification and as directed
by Engineer In-charge.
Providing and placing concrete work including cost of machinery & equipment,
manpower, materials, admixtures and consumables including staging &
scaffolding, handling & transportation, batching, mixing, transportation of
concrete, placing, vibrating to achieve compaction and curing, etc. at all
elevations for :
Providing, laying and jointing RCC NP- 4 Pipe (as per IS:458 latest) for culverts
including testing including fixing collar with cement mortar 1:2 but excluding
excavation, protection works, backfilling, concrete and masonry works in head
Cement shall be in Bidder
15.15 walls and parapets as per approved drawing, Technical specification, MoRTH Rm 245 5,580.00 1,367,100.00
specification and as directed by Engineer In-charge. scope
- 900mm dia.
Pavement marking with hot applied thermoplastic paint including reflectorising
glass beads, concrete primer on concrete surface MoRTH Clause 803, IRC: 35
15.16
and Cls 9.3 of IRC SP:84 - 2014 as per approved drawing, Technical specification,
sqm 81 391.00 31,800.03
MoRTH specification and as directed by Engineer In-charge.
Page 23 of 24
Four lane with Paved shoulder configuration of Bilaspur- Pathrapali Section of NH- 111 (New NH-130) from Km 0.000 (Design Chainage) to
Km 53.300 (Design Chainage) in the State of Chhattisgarh under BharatMala on Hybrid Annuity Mode.
Providing & constructing Medical Aid Post including all civil, architectural,
electrical work upto main panel, plumbing, Plumbing accessories, sanitary ware,
16.05 Doors and Windows, Iron Grill Safety for Windows, Tiles Flooring, Dado, Painting, Sqm - -
water tank, septic tank, borewell, in lock & key conditions, weathering Course
etc. complete as per approved Drawing or Directed by Engineer In charge.
Page 24 of 24