Академический Документы
Профессиональный Документы
Культура Документы
Section Properties
Gauge Fy Wt. I S+ S-
2 4 3
(ksi) (lb/ft ) (in /ft) (in /ft) (in3/ft)
22 38.0 2.18 0.771 0.361 0.449
20 38.0 2.58 0.945 0.467 0.554
18 38.0 3.40 1.330 0.689 0.765
16 38.0 4.22 1.716 0.882 0.949
Notes:
1) Pull out strengths for 12-16 gauge steel supports are determined in accordance with 1996 AISI Cold Formed Steel
Design Manual. (Safety Factor = 3), Miniumum: Fy = 33 ksi (Fu = 45 ksi).
2) Pull over strengths for panels are determined in accordance with 1996 AISI Cold Formed Steel Design Manual. (Safety
Factor = 3), Minimum: Fy = 38 ksi (Fu = 52 ksi).
3) All screw fasteners must have a minimum washer head diameter = 0.400 in.
4) #12-24 Buildex TEKS capacities based on the lesser of pull-out data from ITW Buildex laboratory tests and pull over
calculations based on the 1996 AISI Specifications. (Safety Factor = 3).
5) Hilti fastener capacities based on the following:
a. Loads are based on placement into ASTM A 36 base steel material and metal decking with a minimum yield
point, Fy = 33 ksi.
b. The allowable tension uplift values are based on the lesser of fastener pullout, deck pullover, or fastener tensile
strength failure modes. The values are derived using a minimum factor of safety of five.
6) Arc spot weld values based on an effective weld diameter of ½ inch.
7) Uplift tables based on allowable stress of the panel or allowable capacity of the fasteners.
8) Shaded areas represent conditions where fastener capacity governs.
* All uplift tables based on the minimum attachment pattern.
Minimum number of fasteners per panel is 4. Oct-06
Oct-06
DGN-24
Fastener
Support Capactiy Span (ft.-in.)
Gauge Fastener Thickness [lbs] Span 6-0 7-0 8-0 9-0 10-0 11-0 12-0 13-0 14-0 15-0 16-0
#12-14 SD - 16ga 16ga 165 190 139 107 84 68 56 47 40 35 30 27
#12-14 SD - 14ga 14ga 207 190 139 107 84 68 56 47 40 35 30 27
#12-14 SD - 12ga 12ga 289 190 139 107 84 68 56 47 40 35 30 27
#12-24 Buildex TEKS 3/16 311 190 139 107 84 68 56 47 40 35 30 27
SS
Hilti - ENPH 2-21 L15 > 1/4 325 190 139 107 84 68 56 47 40 35 30 27
Hilti - XEDN-19 THQ12 3/16-3/8 240 190 139 107 84 68 56 47 40 35 30 27
Hilti - XEDNK-22 THQ12 1/8-1/4 240 190 139 107 84 68 56 47 40 35 30 27
Arc Spot Weld 3/16 311 190 139 107 84 68 56 47 40 35 30 27
#12-14 SD - 16ga 16ga 165 152 112 86 68 55 45 38 32 28 24 21
#12-14 SD - 14ga 14ga 207 152 112 86 68 55 45 38 32 28 24 21
#12-14 SD - 12ga 12ga 289 152 112 86 68 55 45 38 32 28 24 21
#12-24 Buildex TEKS 3/16 311 152 112 86 68 55 45 38 32 28 24 21
22 Hilti - ENPH 2-21 L15 > 1/4 325
DS
152 112 86 68 55 45 38 32 28 24 21
Hilti - XEDN-19 THQ12 3/16-3/8 240 152 112 86 68 55 45 38 32 28 24 21
Hilti - XEDNK-22 THQ12 1/8-1/4 240 152 112 86 68 55 45 38 32 28 24 21
Arc Spot Weld 3/16 311 152 112 86 68 55 45 38 32 28 24 21
#12-14 SD - 16ga 16ga 165 191 140 107 85 69 57 48 41 35 30 27
#12-14 SD - 14ga 14ga 207 191 140 107 85 69 57 48 41 35 30 27
#12-14 SD - 12ga 12ga 289 191 140 107 85 69 57 48 41 35 30 27
#12-24 Buildex TEKS 3/16 311 191 140 107 85 69 57 48 41 35 30 27
TS
Hilti - ENPH 2-21 L15 > 1/4 325 191 140 107 85 69 57 48 41 35 30 27
Hilti - XEDN-19 THQ12 3/16-3/8 240 191 140 107 85 69 57 48 41 35 30 27
Hilti - XEDNK-22 THQ12 1/8-1/4 240 191 140 107 85 69 57 48 41 35 30 27
Arc Spot Weld 3/16 311 191 140 107 85 69 57 48 41 35 30 27
Oct-06
DGN-24
DGN-24
DGN-24