Академический Документы
Профессиональный Документы
Культура Документы
co
1. Choose the most appropriate phrase from the 12 35 81 173 357 ___
options given below to complete the following A. 720 B. 820
sentence. C. 725 D. 850
The aircraft ______________ take off as soon as Ans. C.
its flight plan was filed. 35-12 = 23
A. is allowed to B. will be allowed to 81-35 = 46
C. was allowed to D. has been allowed to 173-81 = 92
Ans. C. 357-173 = 184
The sentence given is in passive voice, and the verb So next number will be
used in the second half sentence is “was” so was
allowed to is correct.
1|Page
www.gradeup.co
A. -96 B. -24
C. 24 D. 96
Ans. A.
The determinant of the given matrix is:
2|Page
www.gradeup.co
having velocity V. The velocity at the point of Using Sin law, we get
contact between the object and the floor is
A. zero
B. V in the direction of motion
C. V opposite to the direction of motion
D. V vertically upward from the floor
Ans. A.
We know that the Velocity at point of contact = Rω
(Where, R = Radius of point from Instantaneous
centre)
As per the question, the instantaneous centre is at
intersection of object and floor, hence radius R = 0
Therefore, Velocity at point is zero
22. Biot number signifies the ratio of
20. For the given statements: A. convective resistance in the fluid to conductive
I. Mating spur gear teeth is an example of higher resistance in the solid
pair B. conductive resistance in the solid to convective
II. A revolute joint is an example of lower pair resistance in the fluid
Indicate the correct answer. C. inertia force to viscous force in the fluid
A. Both I and II are false D. buoyancy force to viscous force in the fluid
B. I is true and II is false Ans. B.
C. I is false and II is true As we all know that, Biot number provides a way to
D. Both I and II are true compare the conduction resistance within a solid
Ans. D. body to the convection resistance external to that
Since higher pair has a line or point contact and body (offered by the surrounding fluid) for heat
lower pair has a surface of Area contact. Hence transfer.
both are true. i.e., spur gear has line contact Expressing the same numerically;
(Higher pair) and revolute joint has surface contact hs Volume of the body
(lower pair). Bi ;s
k Surface area
21. A rigid link PQ is 2 m long and oriented at 200
to the horizontal as shown in the figure. The 23. The maximum theoretical work obtainable,
magnitude and direction of velocity 𝑉𝑄 , and the when a system interacts to equilibrium with a
direction of velocity 𝑉𝑝 , are given. The magnitude of reference environment, is called
𝑉𝑝 (in m/s) at this instant is A. Entropy B. Enthalpy
C. Exergy D. Rothalpy
Ans. C.
As per the definition of the Exergy (or) Available
Energy, we know that the maximum portion of
energy which could be converted into useful work
by ideal processes which reduce the system to dead
state is known as Exergy.
As we all know that, for laminar flow, the heat 28. The jobs arrive at a facility, for service, in a
transfer coefficient is minimum where the boundary random manner. The probability distribution of
layer thickness is maximum and vice versa. number of arrivals of jobs in a fixed time interval is
Also for the turbulent-region boundary layer A. Normal B. Poisson
thickness is maximum at 3 but for laminar C. Erlang D. Beta
boundary layer thickness is maximum at 2, hence Ans. B.
the minimum heat transfer coefficient is 2. As we know, that the arrival rates depends upon
the time factor, so Poisson distribution can be
25. For a completely submerged body with centre chosen, but normal distribution expresses same
of gravity ‘G’ and centre of buoyancy ‘B’, the result throughout.
condition of stability will be
A. G is located below B 29. In exponential smoothening method, which one
B. G is located above B of the following is true?
C. G and B are coincident A. 0 ≤ 𝛼 ≤ 1 and high value of a is used for stable
D. independent of the locations of G and B demand
Ans. A. B. 0 ≤ 𝛼 ≤ 1 and high value of a is used for
A body in a liquid is said to be stable only if a small unstable demand
displacement is given then it should returns to its C. 𝛼 ≥ 1 and high value of a is used for stable
original position. demand
Hence the center of gravity 'G' is below the center D. 𝛼 ≤ 0 and high value of a is used for unstable
of Buoyancy 'B' demand
Ans. B.
26. In a power plant, water (density = 1000 kg/𝑚3 ) As we already know, high value of 'α' means more
is pumped from 80 kPa to 3 MPa. The pump has an weightage for immediate forecast.
isentropic efficiency of 0.85. Assuming that the While less value of 'α' means comparatively less
temperature of the water remains the same, the weightage for immediate forecast or almost equal
specific work (in kJ/kg) supplied to the pump is weightage for all previous forecast.
A. 0.34 B. 2.48 Therefore, high value of forecast is only chosen
C. 2.92 D. 3.43 when nature of demand is not reliable instead of
Ans. D. instable
We know that;
Specific volume 30. For machining a rectangular island represented
by coordinates P(0,0), Q(100,0), R(100,50) and
S(0,50) on a casting using CNC milling machine, an
end mill with a diameter of 16 mm is used. The
trajectory of the cutter centre to machine the island
PQRS is
A. (-8, -8), (108, -8), (108, 58), (-8, 58), (-8, -8)
B. (8,8), (94,8), (94,44), (8,44), (8,8)
C. (-8,8), (94,0), (94,44), (8,44), (-8,8)
D. (0,0), (100,0), (100,50), (50,0), (0,0)
Ans. A.
Given; End mill centre ≡ (0,0)
Because Radius of end mill is 8 mm
Therefore; call point 'p' ≡ -8, -8
So;
Call point 'Q' ≡ (100 + 8, –8 + 0) ≡ (108, –8)
Call point 'R' ≡ (108 + 0, 50 + 8) ≡ (108, 58);
27. Which one of the following is a CFC refrigerant? Call point ‘S’ ≡ (108 – 100 – 2 × 8, 58 – 0) ≡ (–
A. R744 B. R290 8,58);
C. R502 D. R7 18 And Call point ‘P’ ≡ (-8-0, 50-50-8) ≡ (-8,-8)
Ans. C.
From all the given refrigerants R502 is the only CFC 31. Which one of the following instruments is widely
refrigerant used to check and calibrate geometric features of
machine tools during their assembly?
A. Ultrasonic probe
B. Coordinate Measuring Machine (CMM)
5|Page
www.gradeup.co
C. Laser interferometer
D. vernier calipers 36. The integral ydx xdy is evaluated along
Ans. C. c
For checking the geometric accuracy of the machine 1
tools we generally use Laser interferometer, the circle x2 y 2 traversed in counter
because it is very cheap and quite easy to handle. 4
clockwise direction. The integral is equal to
32. The major difficulty during welding of aluminum
is due to its A. 0 B.
4
A. high tendency of oxidation
B. high thermal conductivity
C. D.
C. low melting point 2 4
D. low density Ans. C.
Ans. A. Given;
The major difficulty during welding of Aluminum is
its high tendency of oxidation. All other options are
supporting the welding.
6|Page
www.gradeup.co
A. 018 B. 0.36
C. 0.54 D. 0.6
Ans. D.
As mentioned in the question;
Let us first calculate the mean (μ) = exp(x) = 1 × 40. The state of stress at a point is given by σx =
0.3 + 2 × 0.6 + 3 × 0.1 –6 MPa, σy = 4 MPa, and τxy = –8 MPa. The
= 0.3 + 1.2 + 0.3 maximum tensile stress (in MPa) at the point is
= 1.8 __________.
We know that; A. 8.5 B. 3
C. 2.5 D. 2.11
Ans. A.
S.D.
7|Page
www.gradeup.co
F = Force required to move block S + Force 44. An ideal water jet with volume flow rate of 0.05
required to move block R 𝑚3 /𝑠 strikes a flat plate placed normal to its path
Therefore; and exerts a force of 1000 N. Considering the
F = 0.4 × 100 × 9.81 + 0.4 × 250 × 9.81 density of water as 1000 𝑘𝑔/𝑚3 , the diameter (in
= 1.37 kN mm) of the water jet is ______
A. 56 B. 58
42. A pair of spur gears with module 5 mm and a C. 45 D. 60
center distance of 450 mm is used for a speed Ans. A.
reduction of 5:1. The number of teeth on pinion is Taking values from the question;
______ Q = 0.05 m3/s
A. 25 B. 61 Fx = 1000 N
C. 30 D. 55 1000 kg / m3
Ans. C.
Taking the values from the question; Speed ratio = We have to find “D”
5:1 We know that, Fx = Rate of change of momentum
So; in the direction of force
Numerically;
8|Page
www.gradeup.co
k k
A. B.
2m m
2k 5k
C. D.
m m
Ans. D.
We know that, Kinetic energy of the system
1 2
T I (Considering this as Equation (1))
2
Where; I = mass moment of inertia of rod about
point C
Let us take a Point D, which is in the mid of rod i.e.
47. An offset slider-crank mechanism is shown in it is the mid-point
the figure at an instant. Conventionally, the Quick Hence,
Return Ratio (QRR) is considered to be greater than
one. The value of QRR is ____________
A. 1.25 B. 2
C. 1 D. 2.5 Also the,
Ans. A. Potential energy of the system
Let us redraw the picture as:
9|Page
www.gradeup.co
Hence,
Total energy of the system will remain constant
T + k = Constant
50. A 200 mm long, stress free rod at room
temperature is held between two immovable rigid
walls. The temperature of the rod is uniformly
raised by 250°C. If the Young's modulus and
coefficient of thermal expansion are 200 GPa and
respectively, the magnitude of the
longitudinal stress (in MPa) developed in the rod
is _______
A. 600 MPa B. 200 MPa
C. 500 MPa D. 250 MPa
Ans. C.
Given;
10 | P a g e
www.gradeup.co
Qadded = 4158 kJ
A. 625°C B. 400°C
C. 200°C D. 150°C
Ans. A.
We know that;
Entering values;
56. The non-dimensional fluid temperature profile
near the surface of a convectively cooled flat plate
11 | P a g e
www.gradeup.co
is given by where y is
measured perpendicular to the plate, L is the plate
length, and a, b and c are arbitrary constants.
Tw and T are wall and ambient temperatures,
respectively.
if the thermal conductivity of the fluid is k and the
wall heat flux is q", the Nusselt number
is equal to
A. a B. b
C. 2c D. (b+2c)
Ans. B.
We know that;
12 | P a g e
www.gradeup.co
Also
Net Work:
3
65. An aluminium alloy (density 2600 kg/ m )
casting is to be produced A cylindrical hole of 100
mm diameter and 100 mm length is nude m d
3
casting using sand core (density 1600 kg/ m ). The
net buoyancy force (in newto1) acting on the core
is_______
A. P-I, Q-III, R-IV, S-II A. 5 N B. 8 N
B. P-I, Q-IV, R-III, S-II C. 6 N D. 9 N
C. P-II, Q-III, R-IV, S-I Ans. B.
D. P-II, Q-IV, R-III, S-I Taking values from the question;
Ans. D.
In the 25 H7/g8, the H7 is for hole and g is for
shaft respectively, and 7 and 8 indicates their
tolerance grades. We know that; Net buoyancy force = weight of
liquid displaced – weight of solid body
64. If the Taylor's tool life exponent ii is 0.2, and Representing mathematically;
the tool changing time is 1.5 min, then the tool life
(in min) for maximum production rate is ______.
A. 6 min. B. 8 min.
C. 9 min. D. 4 min
Ans. A.
We know that;
***
14 | P a g e