Академический Документы
Профессиональный Документы
Культура Документы
1- The method of prestressing the concrete after it attains its strength is known as:
a) Pre tensioning
b) Post tensioning
c) Chemical prestressing
d) Axial prestressing
2- The uniform prestress in a concrete member subjected to concentric prestressing
is:
a) P/e
b) P/s
c) P/t
d) P/a
3- The diagram indicating the direct stress of the beam is:
4- The tendon profile of given equivalent loading is:
a) ML2/8EI
b) WL3/48EI
c) 5WL4/384EI
d) 12WL4/384EI
6- The concept of load balancing is useful in selecting the:
a) Anchorage profile
b) Bending profile
c) Tendon profile
d) Jack profile
7- A tendon with a trapezoidal profile considering the bending moment and deflection
at the centre of the beam is obtained by:
a) –Pe/6EI(2l12+6l1l2+3l22)
b) –Pe/6EI(2l12+6l1l2+3l22)
c) –Pe/6EI(2l12+6l1l2+3l22)
d) –Pe/6EI(2l12+6l1l2+3l22)
8- The deflection of a beam with parabolic tendon is given as:
a) –5PeL2/48EI
b) –10PeL2/48EI
c) –15PeL2/48EI
d) –3PeL2/48EI
9- The loss in prestress is necessary to make an estimate of:
a) Design
b) Loading
c) Appearance
d) Shear
10- The frictional and anchorage slip losses are observed in:
a) Post tensioned members
b) Pretensioned members
c) Ruptured members
d) Tensile members
SA-1
Question No. 1
The degree of static indeterminacy of a rigid-jointed space frame is
(A) m + r - 2j
(B) m + r - 3j
(C) 3m + r - 3j
(D) 6m + r - 6j
Where m, r and j have
their usual meanings
Question No. 2
Degree of kinematic indeterminacy of a pin-jointed plane frame is
given by
(A) 2j - r
(B) j - 2r
(C) 3j - r
(D) 2
j
Question No. 3
The number of independent equations to be satisfied for static
equilibrium of a plane structure is
(A) 1
(B) 2
(C) 3
(D) 6
Question No. 4
Bending moment at any section in a conjugate beam gives in the actual
beam
(A) Slope
(B) Curvature
(C) Deflection
(D) B
e
n
d
i
n
g
m
o
m
e
n
t
Question No. 5
If there are m unknown member forces, r unknown reaction
components and j number of joints, then the degree of static
indeterminacy of a pin-jointed plane frame is given by
(A) m + r + 2j
(B) m - r + 2j
(C) m + r - 2j
(D) m + r - 3j
Question No. 6
Top most part of an arch is called ________
a) Sofit
b) Crown
c) Center
d) Abutment
Question No. 7
. in influence line diagrams (ILD) :-
a) Points remain fixed, position of load changes
b) Points change, position of loads remain fixed
c) Both of them changes
d) Neither of them changes
Question No. 8
For drawing ILD, what value of test load is assumed?
a) 1 unit
b) Arbitrary
c) Depends upon structure
d) 0
Question No. 9
In Conjugate-Beam method , shear compare with:-
a) Slope
b) Moment
c) Displacement
d) External load
Question No. 10
Fixed joint is replaced by ___________ in conjugate beam.
a) Roller
b) Pin
c) Free end
d) Link
(c) Electricity
(c) Deforestation
(c) Chlorofluorocarbons
(d) Methane
(c) Ammonia
(d) SO
a) N150o
b) E60oS
c) S30o
d) S30oE
4) Fine particles are those particles with size less than _______ mm
diameter.
a) 0.023
b) 0.090
c) 0.075
d) 4.75