Академический Документы
Профессиональный Документы
Культура Документы
ASIGNATURA: MANUFACTURA
DOCENTE: ING. FELIPE GUTIÉRREZ CASTILLO
NOMBRE DE LA PRÁCTICA:
PROCESO BÁSICO TÉRMICO (CALENTAMIENTO Y ENFRIAMIENTO)
GRUPO: 6-2
CICLO ESCOLAR: ENERO-JUNIO 2019
SEMESTRE SEXTO
PROGRAMA EDUCATIVO: LICENCIATURA EN INGENIERÍA INDUSTRIAL
REPORTE DE PRÁCTICA: MANUFACTURA
ÍNDICE
Introduction ...................................................................................................................................................... 2
Overall Objective .............................................................................................................................................. 2
Specific Objective ............................................................................................................................................. 2
Diagrama a bloques .......................................................................................................................................... 3
Desarrollo de la práctica................................................................................................................................... 4
Evidencias fotográficas ..................................................................................................................................... 5
Resultados Obtenidos....................................................................................................................................... 6
Questionnaire ................................................................................................................................................... 6
Ejemplo de aplicación en la vida real ............................................................................................................... 7
Bibliografía ........................................................................................................................................................ 7
Página 1
PROGRAMA EDUCATIVO: LICENCIATURA EN INGENIERÍA INDUSTRIAL
REPORTE DE PRÁCTICA: MANUFACTURA
Introduction
The manufacturing processes describe the transformation of raw materials into finished
products for subsequent commercialization. Sometimes they are known by the term of
secondary industry, as for example, in the semiconductor and steel manufacturing
industry, during a heating and cooling process, we can observe more easily.
However, the heating and cooling processes modify the granular structure of metals and
can produce crystallographic changes in these mechanical properties such as:
• The hardness
• The resistance to tension and rupture.
• The modulus of elasticity and cut.
Overall Objective
Observe the effects of the heating and cooling process by forming a figure (with its initial
letter) by bending a commercial steel bar A-36 by applying temperature.
Specific Objective
Perform a small heat treatment; reaffirm the knowledge acquired in practice number 2 as
well as the safety conditions to handle oxyfuel equipment, correct use of the P.P.E.,
perform the morphology of the oxyfuel process.
Página 2
PROGRAMA EDUCATIVO: LICENCIATURA EN INGENIERÍA INDUSTRIAL
REPORTE DE PRÁCTICA: MANUFACTURA
Diagrama a bloques
INICIO
Preparar equipo
de protección
personal
Trazar líneas de
referencia barra
metálica
Ajustar tornillo de
banco
Calentar la barra
Doblar barra
Detallado
Fin
Página 3
PROGRAMA EDUCATIVO: LICENCIATURA EN INGENIERÍA INDUSTRIAL
REPORTE DE PRÁCTICA: MANUFACTURA
Desarrollo de la práctica
1.- Se realizaron trazos en una barra metálica con el objetivo de formar una figura por
medio de dobleces y ayuda de un calentamiento.
3.- Se colocó y fijo la barra metálica en el tornillo de banco de tal manera que el primer
trazo se pudiera trabajar.
4.- Por medio del equipo de oxicorte se calentó al rojo la zona a doblar de la barra
metálica.
5.- Con ayuda de un tubo usado como palanca y del martillo, realizar el doblez antes de
que se enfriara la zona calentada.
6.- Cuando la zona calentada se enfrió, se retiró la barra del tornillo de banco y se
comparó el doblez realizado.
8.- Una vez formada la figura se eliminó el sobrante de material por medio del equipo de
oxicorte y con ayuda del tornillo de banco.
Página 4
PROGRAMA EDUCATIVO: LICENCIATURA EN INGENIERÍA INDUSTRIAL
REPORTE DE PRÁCTICA: MANUFACTURA
Evidencias fotográficas
Página 5
PROGRAMA EDUCATIVO: LICENCIATURA EN INGENIERÍA INDUSTRIAL
REPORTE DE PRÁCTICA: MANUFACTURA
Resultados Obtenidos
Obtuvimos una barra metálica deformada a partir de su ablandamiento por proceso
térmico, la cual requirió ajustes posteriores debido a la poca precisión de las fuerzas
aplicadas.
Questionnaire
1.- Mention the difference of bending the metal bar in cold and heating the zone of bend:
Heating the fold area is easier to do and fractures are avoided
2.- How did the material behave when bending 90º or less?
There was some ease in applying force and the bending was fast
3.- How did the material behave when bending more than 90º?
The opposite happened with folds smaller than 90 grades
4.- Did the change in the geometry of the bar go exactly to the figure drawn?
No
7.- What do you think was the temperature we use? 80 degrees Celsius
8.- Describe the changes in the properties of the material that were produced, when
heating and cool it: In hot became soft and cold hardened
9.- Could we make these folds without the help of equipment and devices
used? No, we need a specific tool.
Página 6
PROGRAMA EDUCATIVO: LICENCIATURA EN INGENIERÍA INDUSTRIAL
REPORTE DE PRÁCTICA: MANUFACTURA
Bibliografía
Página 7