Академический Документы
Профессиональный Документы
Культура Документы
SECTION-I
Q1) Design the beam for following data, [16]
a) Bending Moment = 42 KN.m
b) Shear force = 30 KN
c) Twisting moment = 12 KN.m
d) Assume width of beam 300mm, Design the beam for torsion effect.
e) Use M20 and Fe 415 Grades of materials.
Q2) A three span continuous beam ABCD is simply supported at A and D and
continuous over support Cand B. The beam carries a load of 230mm thick
3m high brick wall and superimposed load of 15KN/m. Design the beam
using IS code coefficient. Span AB=BC=CD=6m. Unit weight of brick wall
20KN/m3. Use M20 and Fe 415. Sketch the reinforcement details. [16]
Q3) Design a open circular RCC water tank resting on ground. The capacity of
tank is 550000 lit. of water. The joint between wall and base of tank is rigid.
Depth of water tank is 4.5m. Use M20 and Fe 415. Adopt IS code method of
design. Show the reinforcement details. [18]
Q Q Q
-2-
SL - 1054
Seat Total No. of Pages :3
No.
SECTION - I
Q1) a) Explain with neat sketches a mass inflow curve and a demand curve.
How will you determine the reservoir capacity using these two curves?
(Assume constant rate of demand rate in a year) [8]
b) Define sedimentation. Explain with a sketch. Discuss various pre
construction and post construction measures that control silting of a
reservoir. [9]
Q2) a) What are the various factors that govern the selection of type of dam at
a particular site. [9]
b) Discuss various types of earthen dams. What are the modes of failure
of earthen dam. [8]
P.T.O.
SL - 1054
Q4) Write short note on any four. [4 × 4]
b) Loses in reservoir.
e) Instrumentation in dams.
SECTION - II
Q5) a) Explain salient features of Khosla and Blighs theory with regard to
the design of weirs on permeable foundation? [9]
Q6) a) Discuss advantage of canal lining with various types of lining. [9]
Q7) a) Explain the necessity and types of cross drainage works with neat
sketches. [9]
-2-
SL - 1054
Q8) Write short note on any four. [4 × 4]
f) Groynes.
iii
-3-
SL - 997
Seat Total No. of Pages : 2
No.
SECTION - I
Q1) a) State aims & objectives of Town Planning. [8]
b) State the factors to be considered for selection of site for an Ideal Town.[8]
Q5) a) What is Permanent way. State the requirements of a Good Track. [8]
Q6) a) What are the functions of Points & crossings with neat Sketch. [8]
Q7) a) Enlist the different type of Loadings used for designing a Bridge. [8]
a) Culvert
d) Maintenance of Bridges
{{{
-2-
SL-279
Seat Total No. of Pages :2
No.
SECTION-I
Q1) Design an interior panel of flat slab 5 m × 6 m size, with drop and without
column head, for superimposed load of 6 kN/m2. Slab is resting on a column
of size 450 mm × 450 mm. Use M 20 grade concrete and Fe 415 steel.
Calculate the reinforcement along any one side. [25]
Q2) a) A beam 3.7 m deep and 280 mm wide continuous over three clear span
of 5.4 m each with support of thickness 550 mm each carries an uniformly
distributed service load of 170 kN/m2 excluding self weight. Design beam
using M 20 grade concrete and Fe 415 steel. [13]
b) Design a deep beam 280 mm wide and 4.5 m deep simply supported
over a clear span of 5.5 m. The beam carries uniformly distributed service
load of 150 kN/m, excluding self weight. Beam supported on wall of 450
mm thick on each end. Use M 20 grade concrete and Fe 415 steel. [12]
P.T.O.
SL-279
b) Shell thickness
i) at top 200 mm
SECTION-II
Q4) Design a square tank 5.0 m × 5.0 m × 3.0 m deep supported at 6 m height
above ground level. Design vertical wall and flat bottom slab of the tank. Use
M20 grade concrete and Fe250 steel. [25]
Q5) A cantilever type retaining wall has 5 m tall stem. It retains earth level with its
top. The density of earth is 18kN/m3 and angle of repose 30o. The embankment
is horizontal at its top. The SBC of soil may be taken as 200 kN/m2 and the
coefficient of friction between soil and concrete is 0.67. Design the retaining
wall. Take all necessary checks. Adopt M20 grade concrete and Fe415 grade
steel. [25]
Q6) a) Explain the two methods of analyzing a slab using yield line theory.[10]
EEE
-2-
SL-280
Seat Total No. of Pages :2
No.
SECTION-I
Q1) Design a reinforced concrete combined rectangular footing for two columns
A and B located 4.00m apart. The overall sizes of the column A is 360 mm ×
360 mm and column B is 420 mm × 420 mm and the loads on them are 1000
kN and 1400 kN respectively. The boundary line of the property is 400 mm
from the outer face of column A. The bearing capacity of soil obtained from
plate load test is 200 kN/m2. Use M 20 concrete and Fe 415 steel. [25]
P.T.O.
SL-280
SECTION-II
Q4) a) What are the various precautions taken for rectification of tilts and shifts
of well foundation. [13]
Q6) a) Explain with neat sketch rubble mound break water. Also write advantages
of rubble mound break water over other types of break waters. [12]
EEE
-2-
SL-283
Seat Total No. of Pages : 2
No.
B.E. (Civil) (Semester - VIII) (Revised)
Examination, May - 2017
SITE INVESTIGATION METHODS AND PRACTICES (Elective - III)
Sub. Code : 67761
Day and Date : Friday, 05 - 05 - 2017 Total Marks : 100
Time : 2.00 p.m. to 5.00 p.m.
SECTION - I
Q1) Attempt any two: [18]
b) What is need of Site Investigation (SI)? What are the advantages of site
investigation?
P.T.O.
SL-283
Q3) Attempt any two: [16]
a) Explain with a neat sketch Wenner and Schlumberger method of Electrical
resistivity Method of survey.
b) Describe Magnetic Method and writes its advantages.
c) Describe Gravity Method and writes its advantages.
SECTION - II
Q4) Attempt any two: [18]
a) Explain Standard Penetration Test with neat sketch.
b) Write advantages and disadvantages of cone penetration test.
c) Explain field vane shear test.
E E E
-2-
SL-285
Seat Total No. of Pages : 2
No.
B.E. (Civil) (Part - II) (Semester - VIII)
Examination, May - 2017
ADVANCED CONSTRUCTION TECHNIQUES (Elective - III)
Sub. Code : 67764
Day and Date : Friday, 05 - 05 - 2017 Total Marks : 100
Time : 2.00 p.m. to 5.00 p.m.
SECTION - I
Q1) a) State the importance of Plywood Formwork. [8]
b) Explain the term geosynthetics. State their products & application. [8]
P.T.O.
SL-285
SECTION - II
Q5) a) State the operation of Thermal Power Station with sketch. [8]
b) Explain the necessity of Bridge Rehabilitation. [8]
E E E
-2-
SL-284
Seat Total No. of Pages : 2
No.
B.E. (Civil) (Semester - VIII) (Revised)
Examination, May - 2017
INDUSTRIAL WASTE TREATMENT (Elective - III)
Sub. Code : 67763
Day and Date : Friday, 05 - 05 - 2017 Total Marks : 100
Time : 2.00 p.m. to 5.00 p.m.
SECTION - I
Q1) a) Explain various uses of water in industry. [10]
OR
OR
b) What are the measures taken for leakage prevention in industries? [8]
Q3) a) How the water quality monitoring of streams is carried out? [8]
b) Explain in detail actions involved in self purification of streams. [8]
OR
P.T.O.
SL-284
SECTION - II
Q4) a) How the different types of waste treatment & their selections are carried
out? [10]
b) Explain in detail acclimatization of bacteria to toxic wastes. [8]
OR
OR
b) What are the various factors affecting the efficiency of treatment plant.[8]
OR
E E E
-2-
SL-288
Seat Total No. of Pages : 2
No.
B.E. (Civil Engineering) (Part-II) (Semester-VIII)
(Old) Examination, April - 2017
DESIGN OF CONCRETE STRUCTURE-II
Sub. Code : 49175
Day and Date : Saturday, 29-04-2017 Total Marks : 100
Time : 2.00 p.m. to 5.00 p.m.
Instructions : 1) Attempt any three questions from each section.
2) Figures to the right indicates full marks.
3) Assume any suitable data whenever necessary.
4) Use of non-programmable calculator and relevant I.S.456: 2000, IS
1343: 2012 are allowed.
SECTION-I
Q1) A reinforced concrete beam of cross section of size 250×500mm effective is
subjected to a factored shear force of 80 kN, a factored moment of 80 kNm
and a factored torsional moment of 40 kNm. Design the reinforcement to be
provided in the beam. Use M20 grade concrete and Fe 415 grade steel. [17]
Q3) a) Derive expressions for the position of neutral axis of rectangular section?
[4]
b) Design a simply supported RC beam of 8m effective span to carry a
load of 10 kN/m. The ratio of breath to depth is 1:3. Use M20 grade
concrete and Fe 415 grade steel. Adopt working stress method. [12]
Q4) Design a circular tank of capacity 1.5 lakh litres of water. The depth of the
tank is limited to 2.5m. The joint between the wall and base as flexible. The
base slab rest on the ground. Use M25 grade concrete and Fe 415 steel.[16]
P.T.O.
SL-288
SECTION-II
Q5) a) Why anchorage zone has to be given special attention in design? [4]
b) What are advantages of pre-stressing water tank? [4]
c) Explain in brief various concepts with neat sketch in prestressed concrete?
[8]
Q6) A PSC beam supports a live load of 6 kN/m over a simply supported span of
8m. The beam has an I- section with an overall depth of 400mm, width of
flange is 200mm and the thickness of the flange and web are 100 and 80mm
respectively. The beam is to be prestressed by effective prestressing force of
335kN at a suitable eccentricity such that the resultant stress at the soffit of
beam at the center of the span is zero. [17]
a) Find eccentricity required for the force
b) If the tendons is concentric, what should be the magnitude of prestressing
force for the resultant stress to be zero at the bottom fiber of the central
span section?
Q Q Q
-2-
SL-286
Seat Total No. of Pages : 2
No.
B.E. (Civil) (Semester-VIII) (Old)
Examination, April - 2017
TOWN PLANNING AND TRANSPORTTION ENGINEERING
Sub. Code : 49173
Day and Date : Tuesday, 25-04-2017 Total Marks : 100
Time : 2.00 p.m. to 5.00 p.m.
Instructions : 1) Attempt any three questions from both sections.
2) Assume any suitable data if necessary, wherever needed.
3) Figures to the right indicate full marks.
SECTION-I
Q1) a) Explain why town planning is necessary? Explain its principles. [8]
Q2) a) Explain the traffic problems in existing cities. As a town planner what
measures will be suggested by you? [8]
Q3) a) What are four parts of MRTP Act? Explain them in brief. [8]
Q5) a) Describe railway terminus with reference to object, site selection, general
layout and advantages. [8]
Q6) a) Explain signaling and interlocking with reference to definition, object and
functioning. [8]
Q7) a) What is importance of bridge bearings? Explain its types with sketches.
[8]
b) Permanent way
d) Maintenance of bridges
Q Q Q
-2-
SL 1000
SECTION - I
i) Characteristic load.
Q2) A floor system consists of a slab 100 mm thick, cast integrally on beams
spaced at 3.5 m c/c and spanning over 6 m. The beam has a width of 230 mm
and the total depth of the beam including the thickness of slab is 600 mm.
Assume mild exposure condition. The floor is to be designed for a service
load of 3 kN/m2 and 1.0 kN/m2 for finishes excluding the self-weight of the
floor system. Design flexural reinforcement for one intermediate T-beam using
Limit State method. Use M20 concrete and Fe415 steel. [17]
P.T.O.
SL 1000
Q3) a) Explain the concept of bond in RC structures, with a sketch. [4]
b) A rectangular beam with width of section 300 mm and effective
depth = 550 mm has a factored shear of 360 kN at the critical section
near support. The beam is reinforced with 4 - 16 mm. Design shear
reinforcement at support. Use M20 concrete and Fe415 steel. [12]
Q4) a) What are the various remedial measures for control of cracking? [4]
b) A doubly reinforced beam of rectangular section 300 mm wide x 600
mm overall depth is reinforced with 6 - 20 mm diameter on the tension
face and 3 - 20 mm diameter on the compression face. Assume mild
exposure condition. Calculate moment carrying capacity. Use M20
concrete and Fe415 steel. [13]
SECTION - II
Q5) Design a R.C. slab for a room measuring 5 m x 6m. The slab carries a live
load of 4 kN/m2. The slab is simply supported at all the four edges with
corners free to lift. The width of the supporting walls is 300 mm. Use M20
grade concrete and Fe 415 grade steel. Sketch the reinforcement details.
Assume mild exposure condition. [17]
Q6) The clear dimensions of a staircase hall are 3.0 m x 6.0 m. The floor to floor
height is 3.0 m. The landing slabs span in the same direction as the stair and
are supported by the walls at the ends. The stair is used in a commercial
building. Design a dog-legged staircase. Use M 20 concrete and Fe 415 steel.
[17]
Q7) Determine and provide the longitudinal reinforcement and lateral ties in a column
of size 300 x 450 mm. Also check the column for minimum eccentricity if the
unsupported length of column is 3m. Use M-20 and Fe-415. The column is
subjected to ultimate axial load of 1800 kN. [16]
ZZZ
-2-
SL-265
Seat Total No. of Pages : 3
No.
B.E. (Civil) (Semester - VII) (Pre-revised) (Old)
Examination, May - 2017
QUANTITY SURVEYING & VALUATION
Sub. Code : 47902
Day and Date : Tuesday, 16 - 05 - 2017 Total Marks : 100
Time : 2.00 p.m. to 6.00 p.m.
SECTION - I
Q1) Estimate the Quantities for the Combined footing given below, for the following
items of work: [20]
a) Earthwork in Excavation.
b) P.C.C. for bed concrete in 1:3:6.
c) R.C.C M-20 for footing and columns upto G.L only.
d) Total Steel reinforcement for footing and columns upto G.L. only (Cover
for reinforcement - 50 mm for footing and 30mm for columns)
P.T.O.
SL-265
Q2) Draw a Typical cross section of a two storied Load bearing wall made of
Brick masonry and list out the most standard items of works involved with
their brief description with mode of measurement. [15]
Q3) a) What is I.S 1200? What are the principles in selecting the units of
measurement? What are the rules for deductions for plastering work as
per the code? [10]
b) Differentiate between: [5]
i) Plinth Area and Cubical Content method of Approximate Estimate.
ii) Contingencies & Work charged establishments.
Q4) a) Write the detailed specification for Uncoursed Rubble masonry work.[5]
b) What are the units of measurement for [5]
i) pointing
ii) skirting
iii) half brick masonry
iv) door handle
v) Collapsible gate
c) What is meant by Task work? Explain its importance in rate analysis with
suitable examples. [5]
SECTION - II
Q5) a) Prepare a tender Notice for Construction of 10 no of Steel towers for a
mobile company based in New Delhi, with works located in and around
Maharashtra. Assume any other details. [6]
b) Explain in detail Valuation on profit basis. [5]
c) Define the term Gross Cost, Value & Gross Income. [5]
-2-
SL-265
Q6) a) Differentiate between Freehold Property and Lease hold Property? [4]
b) In a plot of land costing Rs 20 lacs a building has been newly constructed
at a total cost of Rs. 60 lacs. The building consists of four flats for four
tenants. The owner expects 15% return on cost of construction and
12% return on cost of land. Calculate the std. rent for each flat of the
building assuming: [12]
i) Life of building = 60 years
ii) Annual repairs cost @ 2% of the cost of construction.
iii) Other outgoings including taxes at 30% of the net return of the
building.
iv) Sinking fund is to be created on 8% interest basis.
Q7) a) Differentiate between single rate years purchase and dual rate years
purchase. [5]
b) List out at least four methods of valuation. Explain valuation based on
direct comparison. [5]
c) A machinery was purchased at Rs. 24 lacs. Assuming salvage value at
Rs. 3 lacs after 7 years.
Calculate depreciation for each year adopting sinking fund method. [6]
E E E
-3-
SL-254
Seat Total No. of Pages : 2
No.
B.E. (Civil Engineering) (Semester-VII) (New) (Revised)
Examination, May - 2017
DESIGN OF CONCRETE STRUCTURES-I
Sub. Code : 67558
Day and Date : Monday, 15-05-2017 Total Marks : 100
Time : 2.00 p.m. to 5.00 p.m.
Instructions : 1) All Questions are Compulsory.
2) Figures to the right indicate full marks.
3) Assume any suitable data wherever necessary.
4) Use of non-programmable calculator and relevant I.S. 456:2000 are
allowed.
SECTION-I
Q1) a) Compare Working Stress Method and Limit State Method of RC design.
[6]
b) Find Xu, max, Pt, lim, and Mu, lim for Fe 415 steel and M20 concrete. [6]
c) Explain the following [4]
i) Characteristic Strength
ii) Partial Safety Factors
Q2) a) State the assumptions made in design of limit state of collapse in flexure.
[4]
b) Determine the moment of resistance of the rectangular RC beam of size
250mm wide and 450mm deep to the centre of tensile reinforcement. It
is reinforced with 2 bars of 16mm diameter as compression reinforcement
at an effective over of 50mm and 4 bars of 25mm diameter as tensile
steel. use M15 concrete and Fe 250 steel. [13]
OR
a) Explain the necessity of doubly reinforced sections. [4]
b) Find the moment of resistance of a T-beam section having following
data. [13]
Width of flange: 800mm Thickness of slab: 120mm
Width of rib: 200mm Effective depth: 400mm
Tensile steel area: 3500mm2 Use M15 concrete and Fe 250 steel
P.T.O.
SL-254
Q3) a) Explain in brief the IS recommendations to control cracks. [4]
b) A simply supported reinforced concrete beam is 250mm wide 500mm
deep to the centre of tensile reinforcement and is reinforced with 4 bars
of 20mm diameter as tensile steel. If the beam is subjected to a factored
shear of 95kN at the support. Design the shear reinforcement consisting
of stirrups. Use M15 concrete and Fe 415 steel.
Show reinforcement details. [13]
SECTION-II
Q4) Design a simply supported one way slab provided over a clear span of 3.30m.
It carries a live load of 4kN/m2 and floor finish of 1kN/m2. Width of supporting
wall is 230mm. Use M20 concrete and Fe 415 steel. Assume moderate
environment. [17]
OR
Design a dog-legged staircase for a building in which the vertical distance
between the floor is 3.6m. The stair hall measures 3.5m × 5m. The live load
may be taken as 3000N/m2. Use 15 concrete and Fe 415 steel. Show
reinforcement details. [17]
Q6) Design a rectangular isolated footing of constant depth for RC column of size
400mm × 600mm bearing a vertical load of 800kN. The safe bearing capacity
of soil may be taken as 120kN/m2. Use M20 concrete and Fe 415 steel. [17]
Q Q Q
-2-
SL-269
Seat Total No. of Pages : 2
No.
B.E. (Civil) (Part - I) (Semester - VII) (Old)
Examination, May - 2017
EXPERIMENTAL STRESS ANALYSIS (Elective - I)
Sub. Code : 47906
Day and Date : Friday, 19 - 05 - 2017 Total Marks : 100
Time : 2.00 p.m. to 5.00 p.m.
SECTION - I
Q1) a) Explain the different methods of applying and generating forces. [8]
b) How does environmental condition affect response of an electrical
resistance strain gauge? Explain any two in detail. [8]
OR
a) Write note on gauge sensitivity and gauge factor. [8]
b) Write step by step procedure for mounting of ERGS. [8]
P.T.O.
SL-269
SECTION - II
Q4) a) Brittle coating method is most suitable field method. Comment. [9]
b) Write note on brittle coating crack pattern. [9]
Q5) a) What is stress optic law? Derive relation for the same. [8]
b) How calibration of photo elastic material is carried out with help of tension
specimen and circular disc under diametrical compression? [8]
Q6) a) How will you sketch composite isoclinic fringe pattern from individual
isoclinic fringe pattern. [8]
b) Why separation of principle stresses is needed? Describe shear difference
method for separation of principle stresses. [8]
OR
Differentiate between (Any four): [16]
a) Polarizer and Analyzer.
b) Whole field method and point to point analysis.
c) Plane and circular polariscope.
d) Ceramic based and resin based brittle coating.
e) White and monochromatic light.
E E E
-2-
SL-275
Seat Total No. of Pages : 2
No.
B.E. (Civil) (Semester - VII) (Pre-Revised) (Old)
Examination, May - 2017
HUMAN RESOURCE DEVELOPMENT (Elective - I)
Sub. Code : 47912
Day and Date : Friday, 19 - 05 - 2017 Total Marks : 100
Time : 2.00 p.m. to 5.00 p.m.
SECTION - I
Q1) a) Discuss the Status of Construction Labour in India. [8]
b) What are the different methods of manpower forecasting? Explain any
one method. [8]
Q3) a) Explain the factors you will consider while selection of constriction project
manager. [8]
b) State advantages & disadvantages of the various sources of
recruitment. [8]
P.T.O.
SL-275
SECTION - II
Q5) a) How will you assess the need of training? [6]
b) What are the different methods of training? Describe in brief any two
methods suitable in Construction Industry. [10]
Q7) a) Discuss the various factors to determine the levels of wage and salary in
construction organization. [8]
b) What are the aspects of health management at construction site? [8]
E E E
-2-
SL-277
Seat Total No. of Pages : 2
No.
B.E. (Civil) (Semester - VII) (Pre-revised) (Old)
Examination, May - 2017
SOLID WASTE MANAGEMENT (Elective - I)
Sub. Code : 47914
Day and Date : Friday, 19 - 05 - 2017 Total Marks : 100
Time : 2.00 p.m. to 5.00 p.m.
Instructions : 1) Que. no. 1 from section I and Que.no. 5 from section II are
compulsory.
2) Solve any two other questions from each of the section.
3) Figures to right indicate full marks.
SECTION - I
Q1) Answer the following (compulsory): [4 × 5 = 20]
a) Explain SWM on basis of need.
b) Why hazardous waste is not considered as a part of MSW?
c) Explain importance of transfer station in SWM.
d) How solid waste can be used as industrial feed?
Q2) a) Explain the importance of collection, storage and transfer in SWM. [7]
b) Explain method of collection, collection vehicle and its suitability. [8]
P.T.O.
SL-277
SECTION - II
Q5) Answer the following (compulsory): [4 × 5 = 20]
a) Explain the different techniques used to control of contamination of
ground water.
b) Explain the fundamentals and objectives of composting.
c) Discuss the air pollution aspect of using incinerators in solid waste
management.
d) Explain the legal aspects of duty of local authority in solid waste
management.
E E E
-2-