Академический Документы
Профессиональный Документы
Культура Документы
WIRELESS DIGITAL
VIDEO MONITORING SYSTEM
WARNING:
STRANGULATION HAZARD - Children has STRANGLED in cords.
Keep this cord out of the reach of children (more than 3 ft (1m) away).
1 x Monitor Unit
NEVER PLACE THE CAMERA OR CORD IN OR NEAR CRIB OR PLAYPEN.
Secure the cord at least three feet away from crib or playpen. 1 x Camera Unit
CHOKING HAZARD - This product contains small parts which may cause choking.
SHOCK WARNING - To prevent electric shock, NEVER use the transmitter or
receiver near water, including near a bathtub, sink, laundry tub, wet basement, etc.
CAUTION - Only insert a battery pack of the same type. Risk of explosion if battery
is replaced with an incorrect type.
Use only the AC adapters provided.
Adult assembly is required. Keep small parts away from children when assembling.
This product is not a toy. Do not allow children to play with it.
This product is NOT intended to replace proper adult supervision of children. 1 x Camera 1 x Monitor 1 x Rechargeable
You MUST check your child’s activity regularly, as this product will not alert parents Power Adapter Charging Adapter Lithium lon Battery
to silent activities of a child.
Before using this product, read and follow all instructions and warnings contained
in this booklet.
This product is not intended for use as a medical monitor and its use should not
replace adult supervision.
Test monitor before use and after changing camera location. Check reception
regularly. Obstacles, such as concrete walls, may shorten the wireless signal
transfer range.
Always unplug AC adapters from power sources during periods of non-use.
Do not touch the plug contacts with sharp or metal objects. 1 x Camera
1 x User Manual 1 x Quick Start Guide Stand Accessories 1 x Pin
01 02
2.2 Product Overview 2.3 Menu Options
2.3.1 Status Indication Overview
LEFT Button RIGHT Button °C/°F Current Camera Unit Temperature 0-50°C / 32-122°F
DOWN Button
Camera Selected camera 1/camera 2/camera 3/camera 4
Volume Up Button
Volume Down Button Alarm Setting (on / off )
Speaker
Reset Charging Port 2.3.2 Menu Options Overview
Antenna
+ Zoom 1.5x, 2x, off
PAIR Key
Night Vision Mode / Anti-Screen Flicker /
Settings
USB Port Default Setting / Temperature Unit
Microphone
Temperature Sensor
03 04
3.Getting Started 1. Connect the Monitor Power Adapter with the Monitor Unit. Plug the Adapter into
the electrical outlet.
Note:
The battery icon turns red on the LCD screen to indicate that the battery
is low, which means the battery needs to be recharged. Fully charging the
battery takes about 4 hours.
When Charging
1. Connect the Camera Power Adapter to the Camera Unit. The indicator on the bottom will turn red and you can see the charging
2. Then the camera starts working. progress bar and a icon on the display.
3. Position your Camera Unit no less than 3 feet away from your baby’s crib. Ensure When Fully Charged
the power cord is not within the reach of your baby. The red indicator the will turn off.
You can use the Monitor Unit while it is being charged.
Note :
Only use the enclosed Camera Power Adapter (5V DC / 1000mA)
配图(可充电电池安装示意图)
1. Press the MENU button of the Monitor Unit and the menu bar will pop up.
2. You will see the Camera option selected, press OK button.
3. Select “Add Camera” and press “OK” button. Pairing starts.
4. Screen appears “60 sec Paring”, poke hole and hold with the pin until screen
1. Insert the Rechargeable Lithium lon Battery into the Battery Compartment as appears “Camera added successfully ”.
shown above.
2. Insert the wire tab of the Rechargeable lon Battery into the contact slots as shown 3.5 Temperature Scale Display Setting
above.
The temperature reading from the temperature sensor at the back of the Camera
3. Replace the battery cover over the compartment.
Unit will be displayed on the top of the screen. To toggle between °C and °F:
Note :
You should release the TALK button after you speak, then you can hear your children.
NOTE:
Monitor Unit Buttons Description A CAM channel needs to be deleted before pairing to a new Camera Unit.
Long-hold button to switch on and off.
POWER ON / OFF / SLEEP button
(WHEN UNIT IS ON) Short press to enter sleep mode
(video off, audio on) 5.2.3 Cycle Cameras
MENU Press to open menu options or exit. This function automatically cycles through your paired camera channels to
display each camera for 5/10/15/30 seconds. This function is only useful if you
TALK button Press and hold to talk to your baby.
have more than 1 Camera Unit paired.
Press to pan Camera Unit viewing direction.
1. Press the MENU button and the menu bar will pop up.
UP DOWN LEFT RIGHT (IN MENU: Press to move menu selection cursor.)
2. Press the UP/DOWN/RIGHT/LEFT button until the Camera icon gets bigger,
Press to cycle cam channels.
OK (IN MENU: Press to confirm selection.)
press OK to enter it, and the Add Camera / Delete Camera / Cycle Cameras
menu will pop up.
Press to lower or increase volume. 3. Press the UP / DOWN button to select Cycle Camera, press OK to confirm.
4. Press the UP / DOWN button to select the desired time from Off, 5sec, 10sec,
1. Press the MENU button and the menu bar will pop up. NOTE:
2. Press the UP/DOWN/RIGHT/LEFT button until the Camera icon gets bigger, You can press OK to select desired camera manually.
press OK to enter it, and the Add Camera / Delete Camera / Cycle Cameras
Note :
2. Press the UP/DOWN/RIGHT/LEFT button until the Sleep Mode icon gets bigger,
press OK to enter it.
A Camera Unit can only be registered to one Monitor Unit at any one time.
3. Press the UP / DOWN button to select the desired time from 1min, 3min, 5min and
5.2.2 Delete a Camera off.
4. Press OK to confirm the desired delay time.
1. Press the MENU button and the menu bar will pop up.
2. Press the UP/DOWN/RIGHT/LEFT button until the Camera icon gets bigger, press
OK to enter it, and the Add Camera / Delete Camera / Cycle Cameras menu will
pop up.
09 10
5.4 Alarm 5.5 Time Setting
5.4.1 Temperature Alert 1. Press the MENU button and the menu bar will pop up.
1. Press the MENU button and the menu bar will pop up. 2. Press the UP/DOWN/RIGHT/LEFT button until the Time Set icon gets bigger, press
2. Press the UP/DOWN/RIGHT/LEFT button until the Temp/Sound Alert icon gets OK to enter it.
3. Press the Left / Right button to select Hours / Minutes for setting, and press the UP
bigger, press OK to enter it, and the Temp Activated Alert / VOX Sensitivity menu
pop up. / DOWN button to set the time.
5.6 Brightness
3. Press the UP/DOWN button to select Temperature Activated Alert, press OK to
confirm, and the High Temp / Low Temp / Alert Duration menu will pop up.
4. Press UP / DOWN button to select High Temp / Low Temp / Alert Duration, 1. Press the MENU button and the menu bar will pop up.
press OK to enter it. 2. Press the UP/DOWN/RIGHT/LEFT button until the Brightness icon gets bigger, press
5. Press UP / DOWN button to select the desired alerting high temperature from OK to enter it.
Off, 24℃, 27℃, 30℃, 32℃. Or desired alerting low temperature from Off, 21℃, 3. Press LEFT / RIGHT button to select the desired brightness level from level 1 ~ 8,
18℃, 16℃, 13℃. Or desired alert duration from 5sec, 10sec, 20sec, 30sec. Press press OK to confirm.
OK to confirm.
5.7 Lullabies (Selections)
NOTE:
You can change the temperature unit (℃/℉) in the Settings. 1. Press the MENU button and the menu bar will pop up.
2. Press the UP/DOWN/RIGHT/LEFT button until the Lullabies icon gets bigger, press
OK to enter it, and the Lullaby 1/2/3/4/5/6/Play All menu will pop up.
5.4.2 Sound Alert (VOX) 3. Press the UP/DOWN button to select desired lullaby or play all, press OK to
1. Press the MENU button and the menu bar will pop up. confirm.
2. Press the UP/DOWN/RIGHT/LEFT button until the Temp/Sound Alert icon gets
bigger, press OK to enter it, and the Temp Activated Alert / VOX Sensitivity menu 5.8 Digital Zoom
pop up.
1. Press the MENU button and the menu bar will pop up.
3. Press the UP/DOWN button to select VOX Sensitivity, press OK to confirm, and
2. Press the UP/DOWN/RIGHT/LEFT button until the Zoom icon gets bigger, press OK
the Sound Level / Alert Duration menu will pop up.
to enter it.
4. Press UP / DOWN button to select Sound Level / Alert Duration, press OK to 3. Press UP/DOWN button to select desired magnification from 1.5x, 2x or Off, press
enter it. OK to confirm.
5. Press UP / DOWN button to select the desired sound level from Off, 1, 2, 3, 4, 5.
Or desired alert duration from 5sec, 10sec, 20sec, 30sec. Press OK to confirm.
5.9 Settings
NOTE: 1. Press the MENU button and the menu bar will pop up.
1. Consider environment diversity, our engineers set up 5 modes of sound 2. Press the UP/DOWN/RIGHT/LEFT button until the Settings icon gets bigger, press
alert, you can adjust on your own needs. OK to enter it, and the Night Vision Mode / Anti-Screen Flicker / Default Settings /
2. W hen setting sound alert, you should turn off the lullabies, otherwise, it Temperature Unit / About /Connect with Us will pop up.
will influence sound alert.
11 12
6. Troubleshooting * Check all connections to the Camera. Confirm that the adapter
is plugged in.
No picture from a * Try recharging or replacing the battery pack.
* Confirm that all cameras and monitors are both ON.
Camera Unit
* Confirm that the Camera and Monitor Unit are ON (check Power * Make sure that the Camera Unit is within range of the monitor.
Product does LED indicator). * Confirm that the Camera and Monitor Unit are paired.
* The battery may be depleted; recharge or replace battery. * Adjust the monitor antenna to vertical position.
not switch on
* Confirm that power adapters are properly connected.
No sound from * Volume setting may be too low. Adjust to a higher setting.
Monitor Unit * Exceeding transmission distance.
* The Camera and Monitor Unit may be too far apart.
* The battery power may be too low.
* Other electronic devices may be interfering with the signal.
* Night vision mode operates in black and white.
* The Camera or Monitor Unit may be in close proximity to large
Reception interference Picture is black and white * Turn on room lights to force monitor out of night vision mode
metallic objects causing interference.
or turn off Night Vision Mode directly.
(Static) * Use of other 2.4GHz products, such as wireless networks (Wifi
routers), Bluetooth systems, or microwave ovens, may cause
interference with this product, Keep Camera and Monitor Unit
at least 5ft (1.5m) away from these items, or turn them off if they * Try moving the Camera Unit closer to the Monitor Unit.
appear to cause interference. * Remove obstructions between the Camera and Monitor Unit.
* Adjust the monitor antenna to vertical position.
The picture playback is not * Use of other 2.4GHz products, such as wireless networks (WiFi
smooth (choppy video with routers), Bluetooth systems, or microwave ovens, may cause
low frame rate) interference with this product. Keep Camera and Monitor Unit
* If the Camera Unit is too far away with low reception, move the at least 5ft (15m) away from these items, or turn them off if
Camera Unit closer to the Monitor Unit. they appear to cause interference.
* Reset both units by disconnecting them from battery and electr-
ical power. Wait about 15 seconds, then reconnect.
* Large metallic objects, including doors, refrigerators, mirrors, fil-
* Battery power may be too lower; recharge or replace battery.
ing cabinets, and also reinforced concrete, may block the radio Noise (static, beeping)
* Possible alarm ring alert.
signal if between the Camera and Monitor Unit.
* Possible out of signal alert.
Camera Unit loses link * The signal strength may be reduced when in close proximity to
* The display position is too close to the camera.
radio or electrical equipment, such as TVs, computers, cordless
with the Monitor Unit
or mobile phones, fluorescent lights or dimmer switches.
* Use of other 2.4GHz products, such as wireless networks (WiFi
routers), Bluetooth systems, or microwave ovens, may cause * Volume may be set too high on the Monitor Unit. Lower volume.
interference with this product. Keep Camera and Monitor Unit * The Camera and Monitor Units may be too close. Move them
at least 5ft (1.5m) away from these items, or turn them off if th- Noise interference on further apart.
ey appear to cause interference. your Monitor Unit * Make sure the Camera and Monitor Units are placed away from
* Pair the Camera Unit under a different channel. other electrical equipment, such as a television, computer or co-
rdless/mobile telephone.
13 14
* The USB Output Adapter may not be properly connected. 7.Specifications
The rechargeable * Battery pack may not be properly connected inside the battery
System General
battery will not charge compartment. Reconnect the wire tab of battery.
* There may be no power from the USB outlet. Switch to another
or no charge light
electrical outlet (if using USB Output Adapter) or another USB RF Frequency: 2400 Mhz-2483.5 Mhz
power source (if using computer/laptop USB power).
Type of Modulation: GFSK
Type of Spread Spectrum: FHSS
Selectable Camera Channels: 4
* Make sure that the Power Adapter is connected to the Camera
Unit.
Data Rate: 4mbps
* Confirm that the Camera Unit is turned ON (Power LED indicator Channel Bandwidth: 3MHz
Pairing failed
shows red light). Transmission Range: up to 200 feet indoor,
* Try pairing to another CAM channel. 700 feet outdoor ( line of sight, no obstruction )
* Poke the “Pair Hole” to re-pairing
Camera Unit
If the above troubleshooting guide did not help you solve your problem, contact our Input Voltage: 100-240VAC
customer service. Our facebook and customer service email address is located in the Operating Voltage: 5V
back of this User Manual. IR/Night Vision: 8 IR LEDS, 1 Low light sensor
Picture Sensor: 720P
Built-Lens: 720P
Operating Temperature: 0° C to +70° C
Power Adapter: 5V, 1000mA
Exposure Control: Auto
White Balance Control: Auto
Vertical Turning Angle: 120° up and down
Horizontal Turning Angle: 350° both left and right
Monitor Unit
Input Voltage: 100-240V AC, @50/60Hz
Operating Voltage: 5V
Resolution (Pixel): 1280 × 768
Battery: 3000mAH Li-ion 3.7V rechargeable battery
LCD Display: 5” TFT color display at 1280 × 768 RGB colors
Power Adapter: Input: 100-240VAC; Output: 5V
Duration (Standby Mode): 24 Hours
Duration (Screen ON): 6 Hours and Above
Time to charge full: About 4 Hours
15 16
8.Camera Stand Installation 9. Warranty Information
We warrant to the original user that this product shall be free from all defects in
1. Install the rubber expansion plugs, and then use the self-tapping screws to lock the material or workmanship for 180 days from the date of purchase,under the
stand base; condition you contact our support email to register it. This warranty does not apply to
any product that has been subject to abuse, misuse, negligence or accident, nor does
it apply to any batteries that may be supplied with the product. Defects caused by
tampering, unauthorized alterations or repairs are not covered by this warranty. We
may elect to replace the entire unit, at no extra cost to you, with the same model or a
similar model or a similar model rather than repair it. If a defect covered by this
warranty should occur, email us with a scanned copy of your original receipt and a
brief explanation of the problem, failing which Samxic will not perform any of its
obligations under this warranty. To return the item, you must use the original
packaging or the equivalent, and you must pay postage.
2. Connect the stand arm to the base with the plastic screw and nut;
DEDICATED CUSTOMER SUPPORT EMAIL
support@samxic.com
This warranty gives you specific legal rights, and you may have other legal rights that
vary from state to state.
2019 Samxic
All rights reserved.
3. Connect the bottom of the camera to the stand arm with the iron screw.
17 18