Академический Документы
Профессиональный Документы
Культура Документы
Total height from the top of pedestal to the bottom of pilecap = 2.55 m
Petrofac Doc. N
Doc. No. 0
Date 21-06-2005
Date 21-06-2005
Date 21-06-2005
Date 21-06-2005
Date 21-06-2005
Date 21-06-2005
Date 21-06-2005
Date 21-06-2005
Date 21-06-2005
Date 21-06-2005
Date 21-06-2005
Date 21-06-2005
Date 21-06-2005
26 (0.9DL
1 + 0.9PE + 0.9ACDL + WT
1.3 ) 322.4 -118.0 -301.0 0.4 1227.8
27 (0.9DL
0 + 0.9PE + 0.9ACDL - WT
2.7 ) 322.3 118.2 301.3 5.0 -1220.7
28 (0.9DL
0 + 0.9PE + 0.9ACDL +-129.7
WL ) -55.1 0.4 0.9 -0.7 367.8
29 (0.9DL
0 + 0.9PE + 0.9ACDL -133.6
WL ) 699.7 -0.2 -0.5 -0.6 -360.4
0 (DL + FP+ LL + 0CL + PE + PO + (0.5/2)PANCL
-132.4+ (0.5)PANCT
516.4 -184.1 -469.5 -139.7 2438.0
1 (DL + FP+ LL + 0CL + PE + PO + (0.5/2)PANCL
-9.5 - (0.5)PANCT
908.9 184.8 471.1 -137.0 -1477.8
2 (DL + FP+ LL + 0CL + PE + PO + (0.5/2)PANCL
-264.2+ (0.5)PANCT
137.4 -64.7 -164.9 -146.1 1564.5
3 (DL + FP+ LL + 0CL + PE + PO - (0.5/2)PANCL
176.0+ (0.5)PANCT
1583.3 -64.5 -164.5 -143.8 112.4
4 (DL + FP+ LL + 0CL + PE + PO + (0.5/2)PANCL
-172.7+ (0.5)PANCT
576.9 -184.0 -469.2 146.0 2559.8
5 (DL + FP+ LL + 0CL + PE + PO + (0.5/2)PANCL
-49.7 - (0.5)PANCT
968.8 184.4 470.2 147.3 -1370.9
6 (DL + FP+ LL + 0CL + PE + PO + (0.5/2)PANCL
-304.5+ (0.5)PANCT
198.2 -64.6 -164.8 140.8 1681.0
7 (DL + FP+ LL + 0CL + PE + PO - (0.5/2)PANCL
135.9+ (0.5)PANCT
1642.6 -64.4 -164.2 138.3 228.7
38 (DL + FP+0 LL + CL + PE + PO + (1.0/2)PANCL
-280.9 + -24.3 -130.7 -333.3 -142.4 2280.3
39 (DL + FP+0 LL + CL + PE + PO + (1.0/2)PANCL
-320.8 + 84.0 -130.6 -333.0 143.3 2407.9
0 (DL + FP+ 0.5LL
0 + CL + PE + PO + ACDL-2.6
+ ACOL + ET/1.4
1004.3 0.4 0.9 4.2 192.4
1 (DL + FP+ 0.5LL
0 + CL + PE + PO + ACDL-2.6
+ ACOL - ET/1.4
1004.3 0.4 0.9 4.2 192.4
2 (DL + FP+ 0.5LL
0 + CL + PE + PO + ACDL-2.6
+ ACOL + EL/1.4
1004.3 0.4 0.9 4.2 192.4
3 (DL + FP+ 0.5LL
0 + CL + PE + PO + ACDL-2.6
+ ACOL - EL/1.4
1004.3 0.4 0.9 4.2 192.4
Petrofac Doc. No. 0
a) in compression = 500 kN
b) in tension = 50 kN
c) in shear = 20 kN
Detail of Materials:
= 750 mm
Clear Cover:
Detail of Pedestals:
Size of Pedestal-1:
Size of Pedestal-2:
a) Pedestals:
= 18.97 kN
= 18.97 kN
= 1427.63 kN
Weight of soil above pile cap = {4.7 x 8.1 - 0.85 x 0.85 - 0.85 x 0.85} 0.75 x 18
= 494.44 kN
Load due to surcharge, if any = {4.7 x 8.1 - 0.85 x 0.85 - 0.85 x 0.85} 0
= 0 kN (No surcharge)
= 1923 kN
Total upward load on pile cap due to the design = 4.7 x 8.1 (2.25 - 0) 10
LpX
Column-1
LpZ
zi
xi
Column-2
Z
PLAN OF PILE CAP
(only to indicate the direction of co-ordinate axes)
Z2 Z5 Z4 Z3 Z1
Column-1
X2 X2
X
X1 X1
Column-2
Z2 Z5 Z4 Z3 Z1
Location of Sections for Bending Moment Calculation (Co-ordinates from the centre of pile cap):
The bending moments are calculated at the outer faces of pedestals and at
Z3-Z3 1500
Z5-Z5 -1500
Location of Sections for Shear Force Calculation (Z co-ordinates for SX and X co-ordinates for SZ):
Ensure +ve co-ordinates for SX1 & SX2, SZ1 & SZ2 and -ve co-ordinates for SX3 & SX4, SZ3 & SZ4.
Section-SX1 = 1950 mm
Section-SX2 = 3500 mm
Section-SX3 = -1950 mm
Section-SX4 = -3500 mm
Section-SZ1 = 500 mm
Section-SZ2 = 1800 mm
Section-SZ3 = -500 mm
Section-SZ4 = -1800 mm
Location of Section for Punching Shear Calculation (distance from the centre of pedestal):
ii) Pedestal-2:
The pile loads are checked against increased capacities for wind/seismic load
Refer the separate sheet giving loads on piles for each load case.
d= 1412.5 mm
K= Mu/bd2 fcu
= 0.011
= 1341.88 mm
Ast = Mu/(0.95 fy z)
= 5393 mm2
Astmin = 9165 mm2 (0.13%, Refer Table 3.25
Diameter of reinforcement = 25 mm
Provide 25 T @ 250 mm c/c (at the bottom of pile cap along Z direction).
d= 1387.5 mm
K= Mu/bd2 fcu
= 0.002
= 1318.13 mm
Ast = Mu/(0.95 fy z)
= 1561 mm2
Astmin = 15795 mm2 (0.13%, Refer Table 3.25
Diameter of reinforcement = 20 mm
Provide 20 T @ 150 mm c/c (at the bottom of pile cap along X direction).
d= 1437.5 mm
K= Mu/bd2 fcu
= 0.038
= 1365.63 mm
Ast = Mu/(0.95 fy z)
= 18054 mm2
Astmin = 9165 mm2 (0.13%, Refer Table 3.25
Petrofac
Petrofac International Limited
Diameter of reinforcement = 25 mm
Provide 25 T @ 125 mm c/c (at the top of pile cap along Z direction).
d= 1412.5 mm
K= Mu/bd fcu
2
= 0.004
= 1341.88 mm
Ast = Mu/(0.95 fy z)
= 3419 mm2
Astmin = 15795 mm2 (0.13%, Refer Table 3.25
Diameter of reinforcement = 25 mm
Provide 25 T @ 250 mm c/c (at the top of pile cap along X direction).
i) along X axis
b= 4700 mm
d= 1412.5 mm
= 1
100 As/bv d = 0.139
Partial safety factor for material gm = 1.25 (Refer 2.4.4.1 of BS 8110:Part 1 - 1997)
\ nc = 0.239 N/mm2
Part 1 - 1997
Distance
between Reinforcemen Allowable
Shear
Factored section & Shear
Section Stress, t Provided - Remarks
SF, kN pedestal av, Stress,
N/mm2 100As/bd
N/mm2
mm
b= 8100 mm
d= 1387.5 mm
100 As/bv d = 0.139
Distance
between Allowable
Shear Reinf
Factored section & Shear
Section Stress, provided - Remarks
SF, kN pedestal av, Stress,
N/mm2 100As/bd
N/mm2
mm
This check is required only for those cases where the spacing of pile exceeds Refer 3.11.4.5 of BS 8110:
3 x dia of pile. For other cases, ignore this check. Part 1 - 1997
Punching load is less than the shear strength of concrete, hence Ok.
ii) Check for punching stress along the perimeter of the pedestal:
Punching stress is less than the allowable shear stress, hence Ok.
Punching stress is less than the allowable shear stress, hence Ok.
iv) Check for punching stress at "1.5d" distance from the pile face:
Maximum punching load, Ppile = 255.96 kN
CONTENTS
Pile Group
Node
Load Case Load on Piles - kN (Effect of design water table is not considered)
No.
P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20
1 26 (0.9DL + 0.9PE + 0.9ACDL + WT ) 160.68 122.91 85.14 47.37 164.8 127.03 89.26 51.49 168.93 131.16 93.39 55.62 173.05 135.28 97.51 59.74 177.17 139.4 101.63 63.86
0 27 (0.9DL + 0.9PE + 0.9ACDL - WT ) 64.2 101.75 139.3 176.84 60.07 97.62 135.17 172.72 55.94 93.49 131.04 168.59 51.81 89.36 126.91 164.46 47.69 85.24 122.79 160.34
0 28 (0.9DL + 0.9PE + 0.9ACDL + WL ) 110.39 99.08 87.77 76.45 110.38 99.07 87.75 76.44 110.37 99.05 87.74 76.43 110.35 99.04 87.73 76.41 110.34 99.03 87.71 76.4
0 29 (0.9DL + 0.9PE + 0.9ACDL - WL ) 114.49 125.58 136.66 147.75 114.5 125.59 136.67 147.76 114.51 125.59 136.68 147.76 114.51 125.6 136.69 147.77 114.52 125.61 136.69 147.78
30 (DL + FP+
0 LL + CL + PE + PO + (0.5/2)PANCL + (0.5)PANCT
221.6 146.61 71.61 -3.39 228.03 153.04 78.04 3.04 234.46 159.47 84.47 9.47 240.89 165.9 90.9 15.9 247.33 172.33 97.33 22.33
31 (DL + 0FP+ LL + CL + PE + PO + (0.5/2)PANCL - (0.5)PANCT
86.31 131.77 177.23 222.69 79.85 125.32 170.78 216.24 73.4 118.86 164.32 209.78 66.95 112.41 157.87 203.33 60.49 105.95 151.42 196.88
32 (DL + FP+
0 LL + CL + PE + PO + (0.5/2)PANCL +170.69
(0.5)PANCT
122.56 74.44 26.31 172.95 124.82 76.7 28.57 175.21 127.08 78.95 30.83 177.47 129.34 81.21 33.09 179.72 131.6 83.47 35.34
33 (DL + 0FP+ LL + CL + PE + PO - (0.5/2)PANCL + (0.5)PANCT
176 172.54 169.08 165.62 178.25 174.79 171.33 167.88 180.5 177.04 173.59 170.13 182.76 179.3 175.84 172.38 185.01 181.55 178.09 174.63
34 (DL + 0FP+ LL + CL + PE + PO + (0.5/2)PANCL + 230.26
(0.5)PANCT
151.51 72.77 -5.98 236.68 157.94 79.19 0.45 243.11 164.37 85.62 6.87 249.54 170.79 92.05 13.3 255.96 177.22 98.47 19.73
35 (DL + 0FP+ LL + CL + PE + PO + (0.5/2)PANCL - (0.5)PANCT
94.21 136.38 178.55 220.73 87.77 129.94 172.11 214.29 81.33 123.5 165.67 207.85 74.89 117.06 159.23 201.41 68.45 110.62 152.79 194.97
36 (DL + FP+
0 LL + CL + PE + PO + (0.5/2)PANCL + 179.11
(0.5)PANCT
127.4 75.69 23.98 181.37 129.65 77.94 26.23 183.62 131.91 80.2 28.49 185.88 134.17 82.46 30.75 188.14 136.43 84.72 33.01
37 (DL + 0FP+ LL + CL + PE + PO - (0.5/2)PANCL + 184.33
(0.5)PANCT
177.3 170.26 163.23 186.58 179.55 172.51 165.48 188.83 181.8 174.76 167.73 191.08 184.05 177.01 169.98 193.33 186.3 179.26 172.23
38 (DL
0 + FP+ LL + CL + PE + PO + (1.0/2)PANCL
191.03
+ 120.88 50.73 -19.42 195.59 125.44 55.3 -14.85 200.16 130.01 59.86 -10.29 204.72 134.57 64.43 -5.72 209.29 139.14 68.99 -1.16
39 (DL
0 + FP+ LL + CL + PE + PO + (1.0/2)PANCL
202.33
+ 128.26 54.19 -19.88 206.9 132.82 58.75 -15.32 211.46 137.38 63.31 -10.76 216.02 141.95 67.87 -6.2 220.58 146.51 72.43 -1.64
40 (DL + 0FP+ 0.5LL + CL + PE + PO + ACDL + ACOL
155.26
+ ET/1.4
149.35 143.43 137.51 155.25 149.33 143.42 137.5 155.24 149.32 143.4 137.49 155.23 149.31 143.39 137.47 155.21 149.3 143.38 137.46
41 (DL + 0FP+ 0.5LL + CL + PE + PO + ACDL + ACOL
155.26
- ET/1.4
149.35 143.43 137.51 155.25 149.33 143.42 137.5 155.24 149.32 143.4 137.49 155.23 149.31 143.39 137.47 155.21 149.3 143.38 137.46
42 (DL + 0FP+ 0.5LL + CL + PE + PO + ACDL + ACOL
155.26
+ EL/1.4
149.35 143.43 137.51 155.25 149.33 143.42 137.5 155.24 149.32 143.4 137.49 155.23 149.31 143.39 137.47 155.21 149.3 143.38 137.46
43 (DL +0FP+ 0.5LL + CL + PE + PO + ACDL + ACOL
155.26
- EL/1.4
149.35 143.43 137.51 155.25 149.33 143.42 137.5 155.24 149.32 143.4 137.49 155.23 149.31 143.39 137.47 155.21 149.3 143.38 137.46
LOAD IN PILES & CHECK FOR PILE CAPACITY
Node
Load Case Load on Piles - kN (Effect of design water table is not considered)
No.
P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20
LOAD IN PILES & CHECK FOR PILE CAPACITY
Node
Load Case Load on Piles - kN (Effect of design water table is not considered)
No.
P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20
LOAD IN PILES & CHECK FOR PILE CAPACITY
Node
Load Case Load on Piles - kN (Effect of design water table is not considered)
No.
P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20
LOAD IN PILES & CHECK FOR PILE CAPACITY
Node
Load Case Load on Piles - kN (Effect of design water table is not considered)
No.
P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20
LOAD IN PILES & CHECK FOR PILE CAPACITY
Node
Load Case Load on Piles - kN (Effect of design water table is not considered)
No.
P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20
LOAD IN PILES & CHECK FOR PILE CAPACITY
Node
Load Case Load on Piles - kN (Effect of design water table is not considered)
No.
P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20
LOAD IN PILES & CHECK FOR PILE CAPACITY
Node
Load Case Load on Piles - kN (Effect of design water table is not considered)
No.
P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20