Вы находитесь на странице: 1из 2

TECHNICAL DATA SHEET

COLOUR RANGE & FINISH


302 EPOXY • Tile Red
• Mid Grey

ESTER FLOOR • Mid Green

• Semi-Gloss Finish
PAINT PACK SIZES
TOUGH, SINGLE PACK EPOXY ESTER • 5lt
FLOOR COATING
RECOMMENDED FILM THICKNESSES
DESCRIPTION AND THEORETICAL COVERAGE
302 EPOXY ESTER FLOOR PAINT is a single pack epoxy
ester floor coating for interior use on concrete, stone, Recommended Film Thicknesses Theoretical Coverage
timber and suitably primed metal. 302 EPOXY ESTER Dry Wet
FLOOR PAINT provides a more durable finish than 30 μm 76 μm 13.0 m²/l
conventional single pack floor paints due to its modified 50 μm 128 μm 7.8 m²/l
epoxy ester formulation.
Practical coverage depends on the application method,
302 EPOXY ESTER FLOOR PAINT provides good painting conditions and the shape and roughness of the
resistance to scuffing, spillages of oil, petrol, detergents surface to be coated.
and dilute aqueous chemical solutions. It can be easily
applied directly to bare concrete or over sound existing
coatings (check compatibility prior to use). An anti-slip DRYING TIMES
finish can be achieved by sprinkling a suitable anti-slip
aggregate onto the wet film of the first coat (consult our DFT 40 μm +10°C +23°C +35°C
Technical Department for full details). Dust Free 6h 4h 3h
Hard Dry 24 h 16 h 10 h
Overcoating Min 24 h 16 h 10 h
ADVANTAGES
Max Indefinite
• Tougher than normal single pack floor paints
• Use on concrete, stone, timber and suitably primed Drying and recoating times are related to the film
metal. thickness, temperature, the relative humidity of the air
• Provides good resistance to scuffing, spillages of and ventilation.
oil, petrol, detergents and dilute aqueous chemical
solutions.
• Single pack and simple to apply.
SURFACE PREPARATION
• Generally compatible with most existing systems. Surfaces should be clean, dry and free from all grease,
• Anti-slip finish available oil, and general contamination.

New Concrete
RECOMMENDED USES The surface must be free from loose dust deposits and
• As a general purpose floor coating for concrete, laitance. Laitance may be removed by abrasive blast
stone, timber and metal where a superior single cleaning, power grinding or acid etching. More than one
pack floor coating is required. application of acid etching may be required to produce
the fine granular surface required for good adhesion.
TECHNICAL DATA
Old Concrete
Volume solids: 40 ± 2% (ISO 3233) (colours – may vary Thoroughly clean all surfaces to remove all dirt, oil
with shade) grease, friable materials and any contamination by a
Weight solids: 52 ± 2% combination of abrasive blast cleaning, power grinding
Specific gravity: 1.01 – 1.15 depending on colour. or detergent washing. If applying over sound existing

Northspeed House | Moorview | Holbeck | Leeds | LS11 9NF


T: +44 (0)1132 455 450 F: +44(0)1132 452 649
E: sales@rawlinspaints.com W: www.rawlinspaints.com
TECHNICAL DATA SHEET

coatings please consult the Technical Department for Store in dry, cool conditions and protect from frost.
advice on compatibility.
VOC
Patching
Volatile Organic Compound content: 490 ± 20 gm/lt,
Use 201 EPOXY REPAIR MORTAR, 203 DEEP REPAIR
varies with colour.
MORTAR and 204 FINE CRACK REPAIR as required,
consult product specific data sheets for further details.
PRODUCT NOTES
APPLICATION CONDITIONS Floors can be back in service after 24 hours but 7 days
should elapse before cleaning with detergents.
The concrete surface must be dry and at least 4 weeks
old. The moisture content of the concrete should not
Minimum recommended application temperature is
exceed 6%. For all applications, only apply in conditions
10°C to ensure adequate through drying.
of good ventilation which should be maintained during
drying. Do not apply when rain, mist, sleet or snow are
imminent. During application and drying time of the HEALTH AND SAFETY
paint coating, the surface should be dry, the Relative Containers are provided with safety labels, which should
Humidity should not exceed 85% and the substrate be observed. Further information about hazardous
temperature should remain at least 3°C above the dew influences and protection are detailed in individual
point. health and safety data sheets. A health and safety data
sheet is available on request from Rawlins Paints
MIXING Limited.
Mix thoroughly prior to applicaton.
The information given in this data sheet is derived from tests and
experience with the products and is believed to be reliable. The
APPLICATION information provided in this Product Data Sheet is intended for general
guidance only and is given in good faith based on Rawlins Paints
Brush or Roller recommended for floor coating. Product Limited current knowledge and experience. No warranty in respect of
may also be airless sprayed – 15 to 19 thou tip and 2000 fitness for a purpose, or any other liability whatsoever can be inferred
from the information contained within this data sheet. The
psi minimum pressure recommended.
information is offered without guarantee to enable purchasers to
determine for themselves the suitability of the product for their
Priming: particular application and should always refer to the most recent issue
In the case of new floors, prime bare concrete by of the Product Data Sheet for the product concerned. All materials are
supplied in accordance with our standard terms and conditions of sale
thinning 10 – 15% using White Spirit. Note that porous
(available upon request). Any specification or advice given by the
surfaces may absorb the first coat. Rawlins Paints Limited or its agents is based on the information
supplied by the purchaser. Rawlins Paints Limited cannot be held
Top Coats: accountable for errors or omissions as a result of that information
being incorrect or incomplete. No undertakings can be given against
Apply undiluted keeping to a wet edge. Do not over
infringement of patents. Some materials are derived from natural
apply or through-drying problems may result. sources. As such some variation may occur. Site conditions may also
contribute to variation in finish and colour. For professional use only.

THINNER
White Spirit

EQUIPMENT CLEANING
Remove remaining paint from equipment, flush
thoroughly with White Spirit until solvent appears
uncontaminated.

FLASH POINT
• 32 - 55°C

STORAGE

Northspeed House | Moorview | Holbeck | Leeds | LS11 9NF


T: +44 (0)1132 455 450 F: +44(0)1132 452 649
E: sales@rawlinspaints.com W: www.rawlinspaints.com

Вам также может понравиться