Академический Документы
Профессиональный Документы
Культура Документы
Features
■ Compatible with SPI bus serial interface
(positive clock SPI modes)
■ Single supply voltage:
– 4.5 to 5.5 V for M95320 and M95640
– 2.5 to 5.5 V for M95320-W and M95640-W
– 1.8 to 5.5 V for M95320-R and M95640-R SO8 (MN)
150 mil width
■ 10 MHz, 5 MHz or 2 MHz clock rates
■ 5 ms write time
■ Status Register
■ Hardware protection of the Status Register
■ Byte and Page Write (up to 32 bytes)
TSSOP8 (DW)
■ Self-timed programming cycle 169 mil width
■ Adjustable size read-only EEPROM area
■ Enhanced ESD protection
■ More than 1 million Write cycles
■ More than 40-year data retention
UFDFPN8 (MB)
■ Packages 2 x 3 mm
– ECOPACK® (RoHS compliant)
Contents
1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2 Signal description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.1 Serial Data output (Q) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.2 Serial Data input (D) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.3 Serial Clock (C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.4 Chip Select (S) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.5 Hold (HOLD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.6 Write Protect (W) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.7 VSS ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.8 VCC supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4 Operating features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.1 Supply voltage (VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.1.1 Operating supply voltage VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.1.2 Device reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.1.3 Power-up conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.1.4 Power-down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.2 Active Power and Standby Power modes . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.2.1 Hold condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.3 Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.4 Data protection and protocol control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5 Memory organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
6 Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
6.1 Write Enable (WREN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
6.2 Write Disable (WRDI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
6.3 Read Status Register (RDSR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
6.3.1 WIP bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2/46
M95320, M95640, M95320-x, M95640-x Contents
8 Maximum rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
9 DC and AC parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
11 Part numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
12 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
3/46
List of tables M95320, M95640, M95320-x, M95640-x
List of tables
4/46
M95320, M95640, M95320-x, M95640-x List of figures
List of figures
5/46
Description M95320, M95640, M95320-x, M95640-x
1 Description
The M95320, M95320-W, M95320-R, M95640, M95640-W and M95640-R are electrically
erasable programmable memory (EEPROM) devices. They are accessed by a high-speed
SPI-compatible bus.
The M95320, M95320-W and M95320-R are 32 Kbit devices organized as 4096 x 8 bits.
The M95640, M95640-W and M95640-R are 64 Kbit devices organized as 8192 x 8 bits.
The device is accessed by a simple serial interface that is SPI-compatible. The bus signals
are C, D and Q, as shown in Table 1 and Figure 1.
The device is selected when Chip Select (S) is taken low. Communications with the device
can be interrupted using Hold (HOLD).
D Q
S M95xxx
HOLD
VSS
AI01789C
M95xxx
S 1 8 VCC
Q 2 7 HOLD
W 3 6 C
VSS 4 5 D
AI01790D
1. See Package mechanical data section for package dimensions and how to identify pin-1.
6/46
M95320, M95640, M95320-x, M95640-x Description
C Serial Clock
D Serial data input
Q Serial data output
S Chip Select
W Write Protect
HOLD Hold
VCC Supply voltage
VSS Ground
7/46
Signal description M95320, M95640, M95320-x, M95640-x
2 Signal description
During all operations, VCC must be held stable and within the specified valid range:
VCC(min) to VCC(max).
All of the input and output signals must be held high or low (according to voltages of VIH,
VOH, VIL or VOL, as specified in Table 13 to Table 16). These signals are described next.
8/46
M95320, M95640, M95320-x, M95640-x Signal description
9/46
Connecting to the SPI bus M95320, M95640, M95320-x, M95640-x
VSS
VCC
SDO
SPI interface with
SDI
(CPOL, CPHA) =
(0, 0) or (1, 1) SCK
AI12836b
1. The Write Protect (W) and Hold (HOLD) signals should be driven, high or low as appropriate.
The pull-up resistor R (represented in Figure 3) ensures that a device is not selected if the
bus master leaves the S line in the high impedance state.
In applications where the bus master might enter a state where all inputs/outputs SPI bus
would be in high impedance at the same time (for example, if the bus master is reset during
the transmission of an instruction), the clock line (C) must be connected to an external pull-
down resistor so that, if all inputs/outputs become high impedance, the C line is pulled low
(while the S line is pulled high): this will ensure that S and C do not become high at the
same time, and so, that the tSHCH requirement is met. The typical value of R is 100 kΩ.
10/46
M95320, M95640, M95320-x, M95640-x Connecting to the SPI bus
CPOL CPHA
0 0 C
1 1 C
D MSB
Q MSB
AI01438B
11/46
Operating features M95320, M95640, M95320-x, M95640-x
4 Operating features
12/46
M95320, M95640, M95320-x, M95640-x Operating features
4.1.4 Power-down
At power-down (continuous decrease in VCC below the minimum VCC operating voltage
defined in Table 8, Table 9 and Table 10), the device must be:
● deselected (Chip Select (S) should be allowed to follow the voltage applied on VCC)
● in Standby Power mode (that is there should not be any internal write cycle in
progress).
HOLD
Hold Hold
Condition Condition
AI02029D
13/46
Operating features M95320, M95640, M95320-x, M95640-x
14/46
M95320, M95640, M95320-x, M95640-x Memory organization
5 Memory organization
HOLD
High Voltage
W Control Logic Generator
S
D
I/O Shift Register
Q
Status
Register Size of the
Read only
EEPROM
area
Y Decoder
1 Page
X Decoder
AI01272C
15/46
Instructions M95320, M95640, M95320-x, M95640-x
6 Instructions
0 1 2 3 4 5 6 7
Instruction
High Impedance
Q
AI02281E
16/46
M95320, M95640, M95320-x, M95640-x Instructions
0 1 2 3 4 5 6 7
Instruction
High Impedance
Q
AI03750D
17/46
Instructions M95320, M95640, M95320-x, M95640-x
18/46
M95320, M95640, M95320-x, M95640-x Instructions
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Instruction
MSB MSB
AI02031E
19/46
Instructions M95320, M95640, M95320-x, M95640-x
20/46
M95320, M95640, M95320-x, M95640-x Instructions
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Instruction Status
Register In
D 7 6 5 4 3 2 1 0
21/46
Instructions M95320, M95640, M95320-x, M95640-x
0 1 2 3 4 5 6 7 8 9 10 20 21 22 23 24 25 26 27 28 29 30 31
D 15 14 13 3 2 1 0
MSB
Data Out 1 Data Out 2
High Impedance
Q 7 6 5 4 3 2 1 0 7
MSB
AI01793D
1. Depending on the memory size, as shown in Table 6, the most significant address bits are Don’t Care.
22/46
M95320, M95640, M95320-x, M95640-x Instructions
0 1 2 3 4 5 6 7 8 9 10 20 21 22 23 24 25 26 27 28 29 30 31
D 15 14 13 3 2 1 0 7 6 5 4 3 2 1 0
High Impedance
Q
AI01795D
1. Depending on the memory size, as shown in Table 6, the most significant address bits are Don’t Care.
23/46
Instructions M95320, M95640, M95320-x, M95640-x
0 1 2 3 4 5 6 7 8 9 10 20 21 22 23 24 25 26 27 28 29 30 31
D 15 14 13 3 2 1 0 7 6 5 4 3 2 1 0
32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47
D 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 6 5 4 3 2 1 0
AI01796D
1. Depending on the memory size, as shown in Table 6, the most significant address bits are Don’t Care.
24/46
M95320, M95640, M95320-x, M95640-x Power-up and delivery state
25/46
Maximum rating M95320, M95640, M95320-x, M95640-x
8 Maximum rating
Stressing the device outside the ratings listed in Table 7 may cause permanent damage to
the device. These are stress ratings only, and operation of the device at these, or any other
conditions outside those indicated in the operating sections of this specification, is not
implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability. Refer also to the STMicroelectronics SURE Program and other relevant
quality documents.
26/46
M95320, M95640, M95320-x, M95640-x DC and AC parameters
9 DC and AC parameters
This section summarizes the operating and measurement conditions, and the DC and AC
characteristics of the device. The parameters in the DC and AC characteristic tables that
follow are derived from tests performed under the measurement conditions summarized in
the relevant tables. Designers should check that the operating conditions in their circuit
match the measurement conditions when relying on the quoted parameters.
CL Load capacitance 30 pF
Input rise and fall times 50 ns
Input pulse voltages 0.2VCC to 0.8VCC V
Input and output timing reference voltages 0.3VCC to 0.7VCC V
1. Output Hi-Z is defined as the point where data out is no longer driven.
0.3VCC
0.2VCC
AI00825B
27/46
DC and AC parameters M95320, M95640, M95320-x, M95640-x
28/46
M95320, M95640, M95320-x, M95640-x DC and AC parameters
29/46
DC and AC parameters M95320, M95640, M95320-x, M95640-x
30/46
M95320, M95640, M95320-x, M95640-x DC and AC parameters
31/46
DC and AC parameters M95320, M95640, M95320-x, M95640-x
32/46
M95320, M95640, M95320-x, M95640-x DC and AC parameters
33/46
DC and AC parameters M95320, M95640, M95320-x, M95640-x
34/46
M95320, M95640, M95320-x, M95640-x DC and AC parameters
35/46
DC and AC parameters M95320, M95640, M95320-x, M95640-x
tSHSL
tCHDX
D MSB IN LSB IN
High impedance
Q
AI01447d
tHLCH
tCLHL tHHCH
tCLHH
tHLQZ tHHQV
HOLD
AI01448c
36/46
M95320, M95640, M95320-x, M95640-x DC and AC parameters
tCH tSHSL
tCLQX
tQLQH
tQHQL
ADDR
D LSB IN
AI01449f
37/46
Package mechanical data M95320, M95640, M95320-x, M95640-x
Figure 18. SO8N – 8 lead plastic small outline, 150 mils body width, package outline
h x 45˚
A2 A
c
ccc
b
e
0.25 mm
D GAUGE PLANE
k
8
E1 E
1 L
A1
L1
SO-A
Table 22. SO8N – 8 lead plastic small outline, 150 mils body width, package
mechanical data
millimeters inches(1)
Symbol
Typ Min Max Typ Min Max
A 1.75 0.0689
A1 0.10 0.25 0.0039 0.0098
A2 1.25 0.0492
b 0.28 0.48 0.011 0.0189
c 0.17 0.23 0.0067 0.0091
ccc 0.10 0.0039
D 4.90 4.80 5.00 0.1929 0.189 0.1969
E 6.00 5.80 6.20 0.2362 0.2283 0.2441
E1 3.90 3.80 4.00 0.1535 0.1496 0.1575
e 1.27 – – 0.05 - -
h 0.25 0.50 0.0098 0.0197
k 0° 8° 0° 8°
L 0.40 1.27 0.0157 0.05
L1 1.04 0.0409
1. Values in inches are converted from mm and rounded to 4 decimal digits.
38/46
M95320, M95640, M95320-x, M95640-x Package mechanical data
Figure 19. TSSOP8 – 8 lead thin shrink small outline, package outline
D
8 5
c
E1 E
1 4
A1 L
A A2
CP L1
b e
TSSOP8AM
Table 23. TSSOP8 – 8 lead thin shrink small outline, package mechanical data
millimeters inches(1)
Symbol
Typ. Min. Max. Typ. Min. Max.
A 1.200 0.0472
A1 0.050 0.150 0.0020 0.0059
A2 1.000 0.800 1.050 0.0394 0.0315 0.0413
b 0.190 0.300 0.0075 0.0118
c 0.090 0.200 0.0035 0.0079
CP 0.100 0.0039
D 3.000 2.900 3.100 0.1181 0.1142 0.1220
e 0.650 – – 0.0256 – –
E 6.400 6.200 6.600 0.2520 0.2441 0.2598
E1 4.400 4.300 4.500 0.1732 0.1693 0.1772
L 0.600 0.450 0.750 0.0236 0.0177 0.0295
L1 1.000 0.0394
α 0° 8° 0° 8°
1. Values in inches are converted from mm and rounded to 4 decimal digits.
39/46
Package mechanical data M95320, M95640, M95320-x, M95640-x
Figure 20. UFDFPN8 (MLP8) - 8-lead ultra thin fine pitch dual flat no lead, package
outline
D e b
L1
L3
E E2
L
A
D2
ddd
A1
UFDFPN-01
Table 24. UFDFPN8 (MLP8) - 8-lead ultra thin fine pitch dual flat no lead, package
mechanical data
millimeters inches(1)
Symbol
Typ Min Max Typ Min Max
40/46
M95320, M95640, M95320-x, M95640-x Part numbering
11 Part numbering
Example: M95640 – W MN 6 T P /P
Device type
M95 = SPI serial access EEPROM
Device function
640 = 64 Kbit (8192 x 8)
320 = 32 Kbit (4096 x 8)
Operating voltage
blank = VCC = 4.5 to 5.5 V
W = VCC = 2.5 to 5.5 V
R = VCC = 1.8 to 5.5 V
Package
MN = SO8 (150 mils width)
DW = TSSOP8 (169 mils width)
MB = MLP8 (2x3 mm)
Device grade
6 = Industrial temperature range, –40 to 85 °C.
Device tested with standard test flow
3 = Device tested with high reliability certified flow(1)automotive temperature range
(–40 to 125 °C)
Option
blank = Standard Packing
T = Tape and Reel Packing
Plating technology
P or G = ECOPACK (RoHS compliant)
Process letter(2)
/P or /PB = DP26% Chartered
1. ST strongly recommends the use of the Automotive Grade devices for use in an automotive environment.
The high reliability certified flow (HRCF) is described in the quality note QNEE9801. Please ask your
nearest ST sales office for a copy.
2. The Process letter only concerns Grade-3 devices.
For a list of available options (speed, package, etc.) or for further information on any aspect
of this device, please contact your nearest ST sales office.
41/46
Part numbering M95320, M95640, M95320-x, M95640-x
Table 26. Available M95320x products (package, voltage range, temperature grade)
M95320 M95320-W M95320-R
Package
4.5 V to 5.5 V 2.5 V to 5.5 V 1.8 V to 5.5 V
Range 6
SO8 (MN) Range 3 Range 6
Range 3
Range 6
TSSOP (DW) - Range 6
Range 3
MLP 2 × 3 mm (MB) - - Range 6
Table 27. Available M95640x products (package, voltage range, temperature grade)
M95640 M95640-W M95640-R
Package
4.5 V to 5.5 V 2.5 V to 5.5 V 1.8 V to 5.5 V
Range 6
SO8 (MN) Range 3 Range 6
Range 3
Range 6
TSSOP (DW) - Range 6
Range 3
MLP 2 × 3 mm (MB) - - Range 6
42/46
M95320, M95640, M95320-x, M95640-x Revision history
12 Revision history
Human Body Model meets JEDEC std (Table 2). Minor adjustments on pp
13-Jul-2000 1.2 1,11,15. New clause on p7. Addition of TSSOP8 package on pp 1, 2,
Ordering Info, Mechanical Data
Test condition added ILI and ILO, and specification of tDLDH and tDHDL
removed.
tCLCH, tCHCL, tDLDH and tDHDL changed to 50ns for the -V range.
“-V” Voltage range changed to “2.7V to 3.6V” throughout.
16-Mar-2001 1.3
Maximum lead soldering time and temperature conditions updated.
Instruction sequence illustrations updated.
“Bus Master and Memory Devices on the SPI bus” illustration updated.
Package Mechanical data updated
19-Jul-2001 1.4 M95160 and M95080 devices removed to their own data sheet
Endurance increased to 1M write/erase cycles
06-Dec-2001 1.5
Instruction sequence illustrations updated
18-Dec-2001 2.0 Document reformatted using the new template. No parameters changed.
Announcement made of planned upgrade to 10MHz clock for the 5V, –40
08-Feb-2002 2.1 to 85°C, range.
Endurance set to 100K write/erase cycles
10MHz, 5MHz, 2MHz clock; 5ms, 10ms Write Time; 100K, 1M erase/write
18-Dec-2002 2.2 cycles distinguished on front page, and in the DC and AC Characteristics
tables
Process identification letter corrected in footnote to AC Characteristics
26-Mar-2003 2.3
table for temp. range 3
-S voltage range upgraded by removing it and inserting -R voltage range
26-Jun-2003 2.4
in its place
15-Oct-2003 3.0 Table of contents, and Pb-free options added. VIL(min) improved to -0.45V
21-Nov-2003 3.1 VI(min) and VO(min) corrected (improved) to -0.45V
28-Jan-2004 4.0 TSSOP8 connections added to DIP and SO connections
M95320-S and M95640-S root part numbers (1.65 to 5.5V Supply) and
related characteristics added.
20MHz Clock rate added.TSSOP14 package removed and MLP8 package
added.
Description of Power On Reset: VCC Lock-Out Write Protect updated.
24-May-2005 5.0 Product List summary table added. Absolute Maximum Ratings for
VIO(min) and VCC(min) improved. Soldering temperature information
clarified for RoHS compliant devices. Device Grade 3 clarified, with
reference to HRCF and automotive environments. AEC-Q100-002
compliance. tCHHL(min) and tCHHH(min) is tCH for products under “S”
process. tHHQX corrected to tHHQV.
Figure 16: Hold timing updated.
43/46
Revision history M95320, M95640, M95320-x, M95640-x
44/46
M95320, M95640, M95320-x, M95640-x Revision history
45/46
M95320, M95640, M95320-x, M95640-x
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
46/46