Академический Документы
Профессиональный Документы
Культура Документы
14)
Before
Using
Thank you for purchasing PIVOT product.
AUTO CRUISE & THROTTLE
Please read this manual carefully and keep it for future
reference.
Features
●If this product is given to
another user, make sure to
include this User’s Manual.
Product +
Contents
Connecting
The Wires
Before Using / Contents ……………………………………… 1 procedure 4 Speed Pulse Settings…………………………… 8
The Product
Installing
How to Operate…………………………………………… 9 〜11
WARNING / CAUTION ……………………………………… 3
Operating the Throttle Controller ………………………… 9
procedure 1 Connecting The Wires ……………………… 4 〜5
Operating the AUTO CRUISE
Brake Switch ………………………………………………… 4
Mode Setting / Set and Deactivate ……………………… 10
Car Speed Signal / Earth / Reverse Signal /
Adjust Level ………………………………………………… 11
Specialized Harness ……………………………………… 5
Settings
Initial
Test Drive ……………………………………………………… 11
procedure 2 Installing The Product ………………………… 6
Troubleshooting ………………………………………… 11 〜12
procedure 3 Initial Settings (Degree of Acceleration Setting) …… 7
Speed Pulse
Settings
After installation, make sure to carry out “Initial Settings”.
After having installed this product, make sure to make settings for your car’s special characteristics by carrying out the
Operate
How to
“Initial Settings” on Page 7. If the “Initial Settings” are not carried out, a Check Engine Light may go on. Also, the unit will
remain in NORMAL Mode even if the Mode is switched.
Shooting
Trouble-
Only use 3-drive Specialized Harness.
Using another type of harness will cause troubles and failure; use only the 3-drive specialized harness.
This product can not be installed in car models which come with standard
auto-cruise control.
Only use with Manufacturer’s Original ECU.
Do not install this product if the ECU is not the original one or when a sub-ECU is being used.
Insulating
Tapes
Crimpers
Cut
User’s Manual Wiring Chart and others
Zip Ties ×2 Voltage Detector Connectors
1
(This Book) (in Japanese)
×4
Features
Before
Using
control over acceleration response for both sports driving and Eco-driving.
Compact All-in-One Body This compact all-in-one body
makes it possible to install in out of the way places such as 12-Step Adjustment A wide variety of possible adjustments to meet
storage box or near the steering wheel. you need; 7 for Sports and 5 for Eco.
Digital Control Micro-computer control means less noise and Acceleration Monitor This shows the amount of acceleration;
less heat. especially useful when trying to be careful about not over accelerating as in
The Product
Installing
Eco-driving.
Initial Setting Method Stable balanced control is possible by
running the “Initial Settings” program after having finished Performance Results of Each Mode (0-400 m)
installation; this will help reduce troubles caused by voltage ・HONDA STEP WGN (RG1)
differences found in each car model.
Normal 23
Settings
AUTO CRUISE AUTO CRUISE allows you to set the most Ec5 6.9 km/L (58 cc )
suitable speed to cruise at while driving; resulting in superior
fuel-efficiency. (Approx. 30 ∼ 140 km/h)
AT Gear Position Pattern ・VW GOLF GTI (1KAXX)
Stable Speed Control Our exclusively designed system
2nd 3rd
lessens quick changes in speed; bringing you automatic cruise SP7
Operate
Normal
User-Friendly Switch for Smooth Operation The 2nd 3rd 4th 5th 6th
Ec5
separate switch allows for easy one-handed operation and installs
almost anywhere with double-sided tape. 0 20 40 60 Speed (km/h)
Deactivating Operation Stepping on the brake while SP7: MAX. SPORTS Mode Ec5: MAX. ECO Mode Degree of acceleration: 30%
Shooting
Trouble-
Auto-Cruise is activated will deactivate its operation and return to ※In models with CVT or in which changes in speed bring less shock, the noticeable
normal driving mode. Auto-Cruise will also be deactivated when the differences may be less.
“Set” switch is pressed, if the brake fuse burns out, or if the speed is
much lower than the set speed. Examples of Changes in Throttle Opening ・SUZUKI SWIFT(ZC31S)
Prevent Abnormal Acceleration Our safety design uses a 100
microcomputer to monitor two kinds of output signal and if an SP7:
Throttle Opening (%)
2
Before
Using
Part Names
3 AC Switch
Features
AUTO CRUISE & THROTTLE
1 UP Switch AC
For AUTO CRUISE Mode Settings
For Deactivating AUTO CRUISE
2 DOWN Switch MODE
4 MODE Switch
For Changing Settings
5 SET Switch
For Switching Modes
Connecting
For Setting/
The Wires
For Deactivating AUTO CRUISE
Deactivating AUTO
Turning off the Display Display CRUISE
The Product
Installing
the engine has been turned off; this is normal.
Display Items
Settings
Initial
Display Items Display for Settings
Display Details Display Details
Speed Pulse
SPORTS Mode (higher number = higher response) Initial Settings Mode
Settings
Position when accelerator is
ECO Mode (higher number = lower response) not pressed down.
Position when accelerator is
NORMAL (Normal Performance) fully pressed down.
Operate
How to
AUTO CRUISE Mode: ON Speed Pulse Setting Mode
Shooting
AUTO CRUISE in Operation Adjust AUTO CRUISE Level
Trouble-
Reverse (when in SPORTS Mode only)
●When making initial settings make ●Do not crush the cable. Please be ●While driving DO NOT operate
sure to stop the engine and place in careful that the cable does not get switches or pay prolonged attention
WARNING Parking or Neutral. It is dangerous crushed by the seat rail or car door to the display; it is extremely dan-
to carry out these settings while the steel plate, nor cut by any sharp gerous.
Improper use or disregard engine is running. steel plate as this may cause a ●Make sure that all wiring and fas-
of these warnings may re- ●Do not work in areas where there is poor connection or an electric short tening down of the product does
sult in the injury or death excessive exhaust. Due to vehicle leading to fire or other danger. not interfere with driving nor be
of people. exhaust emission poisoning or fire done in such a way as to cause
may result in a damage to humans. poor connections.
●PIVOT Corporation accepts no re- ●If the device is improperly installed ●Please wipe with a soft dry cloth (a
sponsibility, in any manner whatso- or settings have been improperly lens cloth).
ever, for damage and/or trouble to made a Check Engine Light may go ●Please do not use alcohol or ben-
your vehicle or product, nor for any on.
CAUTION accidents that are the result of the ●Do not use electrotap.
zine.
This may cause damage to the
misuse of this product.
Improper use or disregard ●Wiring should be carried out using painted surface or cracks in the
●Please confirm that the type of ve- plastic.
of these warnings may the attached “cut connector” or by
hicle you wish to install into is listed
cause injury to persons, soldering, make sure to securely in- ●Do not, in any manner, process,
in the “list of Specialized Harnesses
damage the product and/or sulate all wiring parts with insula- take apart, or make changes to this
by Car Model for 3-drive・AC”.
other things. tion tape, and confirm that no wires product.
●When installing this product, we are sticking out.
recommend that if technical knowl-
edge becomes necessary please
consult a qualified mechanic.
3
procedure 1 Connecting The Wires
Basic Wiring When installing make sure to use the correct Specialized Harness for your car model.
Before
Using
(1.5m)
SET (1m) Pink R Reverse Signal
Switch (1.5m)
Black Earth
2 P Connector (1.5m)
Features
(0.5m) 6P Connector
The Wires
(0.5m)
SP
Accelerator Option
※Please make sure to connect
Connector
the Red wire to the brake
The Product
ECU, etc...
Installing
●When connecting to the car side wires, do not only use “electrotap” as this may result in a poor
Initial
electrical connection. Please use the supplied “cut connectors” or solder the wires together and
make sure to use insulation tape to securely insulate the wire connection.
●The Brake Switch Connectors will differ depending upon the car model, grade and year, so please sure to check the design in the “Wiring Chart”.
●Remove the battery cables from the minus terminals before carrying out the wiring.
Speed Pulse
Brake directed.
tor. Check the wiring position in the Pedal ② In case of the car model which is blank of Wire Numbers or Brake
“Wiring Chart” and after testing the Harness Connection Color of “Wiring Chart” , please make sure to
voltage, carry out the wiring.
carry out a voltage test and connect as directed.
●After having completed the wiring confirm that the brake lamp
is working properly. Connect Directly
Shooting
Trouble-
When there are four(or more) wires, do not wire 直接接続 ブレーキ ハーネス
ブレーキ
to positions A and B as shown below. (See below 車名 年式 ハーネス 接続番号 接続色 Connection
for how to check the voltage for each wiring position) 品番 製品の コー ド色 Numbers
Four Wires 赤 灰 赤 灰
Red Gray アルファード・ H20.5 ∼ BR-1 1 2 青 黄
ヴェルファイア
Brake
Gray
Lamp Earth Red Gray
Brake 2 Wire leading
Key Switch IGN 1 2
(12V with key A Switch B 1 from product
Operation Signal
in ON position) 3 4 Switch Red
(BR-1) Connector
: Use Cut Connector
How to Test (⇒Refer to page 5【Reference 1】“How to use the Voltage Detector” ) Connect Using Brake Harness (sold separately)
1. Turn the key to OFF or LOCK. Please put gear into P (Parking) Connect the Red and Gray wires to the corresponding
or N (Neutral). wire colors found in the “Wiring Chart” . Wiring
2. Check the terminal for each of the connections as designated in (⇒For more details , please refer to the brake harness manual.) Chart
the separate sheet “Wiring Chart” . e.g.) TOYOTA ALPHARD (H20.5 〜 )
TOYOTA
The Wire color Not Press Down Press Down
of the product on Brake Pedal on Brake Pedal 直接接続
ブレーキ
ブレーキ ハーネス
Red (12V) (12V) Brake power 接続色 Connection
車名 年式 ハーネス 接続番号
Gray (0V) (12V) Brake switch signal 製品のコード色 Colors
品番
: Voltage Tester Lamp ON : OFF 赤 灰 赤 灰
If there are four(or more) wires, do not wire the remaining (OFF 0V). アルファード・ H20.5 ∼ BR-1 1 2 青 黄
4
ヴェルファイア
Car Speed Signal Reverse Signal
Confirm the positions on the “Wiring By wiring to reverse, it is possible when in SPORTS Mode to
Orange Chart” and then connect using Cut Wiring automatically switch to NORMAL Mode when the gear is put
Before
Connectors. into R (Reverse). Also, during this time it will become
Using
Chart
(⇒Refer to 【Reference
“ 2】How to use the impossible to set to AUTO CRUISE.
Connector” below.) ※When put into reverse, the degree of acceleration is small and
※Some MITSUBISHI. SUZUKI and NISSAN models require a sepa- quick acceleration will not occur; it is not necessary to wire for
rate speed pulse adapter. reverse.
※Connect only to the cables on the car side as directed. ※This does not operate when in ECO Mode or NORMAL Mode.
Features
(Do not wire the speed signal to the CAN-BUS adaptor.)
● Gear Position
Earth
Pink When in R (Reverse) = 12V, other positions = 0V
Fasten to a screw (How to Test) With Key switched to ON (engine not operating) put
Black with earth
terminal of a metal part gear into reverse.
Connecting
The Wires
which is earthed. (How to Wire) Cut the black tube of the wire tip and connect referring
※Painted screws and screws connected to plastic parts are not the diagrams below.
earthed; make sure to connect only to a place which is earthed.
If wiring to the Reverse Signal
Special Model Specific Harness (sold separately) Reverse Switch Backup Light
Connect to the 6-pin
The Product
6P
Installing
connector on the Pink wire
Connector specialized harness. for Reverse Signal
Main Unit Earth
Only disconnect the accelerator connector after having : Use Cut Connector
waited at least 15 minutes from the time that the key
was turned OFF. If wiring to the optional connector of the car maker’ s
Depending on the type of vehicle, if the connector is disconnected original navigation system
before the ECU power is switched OFF the Check Engine Light may
Settings
Initial
go on. (If the Light comes on: ⇒ Refer to Page 12, “How to Turn Off
the Check Engine Light”) Optional connector of
the car maker’ s original Normal
Accelerator : No wiring
Passage of over navigation system
Speed Pulse
Turn the key Connector
When using a different
15
Settings
minutes
to OFF. Accelerator Other company’ s company’s navigation
navigation systems system do not wire to
LOCK or back cameras Main Unit the reverse cable.
(OFF) Disconnect : Use Cut Connector
the connector
(Check Wiring)
Operate
How to
※For details about connecting the specialized harness, please refer to If in SPORTS Mode, when the reverse signal is input the
the user’ s manual that came with that harness. display will read “bAc” and the unit will switch to NORMAL
Mode.
※If the cable in not long enough, use the extension cable “THC-EC
(sold separately for ¥1,500)” .
SET Switch Wiring for when you wish not use AUTO CRUISE
Shooting
Trouble-
Connect to the 2-pin Red Normally 12V (OK for other than brake)
2P connector leading from Black Earth
Connector the unit.
Gray Orange Do not connect to anywhere
5
procedure 2 Installing The Product
Before
Using
While in use if wires become free they may interfere with driving and cause accidents.
Please be sure to bundle away
Also, wires which are smashed or crushed may result in a short and can be extremely
all wires with tape, etc…
dangerous.
Features
tape (Included)
Installing
(Included) Screw
Clean to
remove Double-sided
oil and dust. tape (Included)
Settings
Initial
Installing The SET Switch If you wish to install the switch to a round shaped lever, please
purchase separately a Lever Spacer.
Install the SET switch to a position which is easy to operate.
Speed Pulse
SET
Switch
Double-sided
tape
Operate
How to
(Included)
Clean to
remove
oil and dust.
(Example of Installation at a lever)
Shooting
Trouble-
●Lever Spacer Set (17, 26, 28, 32mm) ; Sold separately for ¥762
(How to Install) (Example of the Spacer Installation) 【Lever Diameters of Major Car Models】
SET Lever Lever Lever
Switch Spacer Lever Type of Car
Diameter
6
procedure 3 Initial Settings (Degree of Acceleration Setting)
Make sure to carry out these settings.
Before
Using
● This operation sets the car’ s accelerator
When installing for When installing into a characteristics into the controller unit.
the first time different car ● If the “Initial Settings” are not carried out,
the unit will remain in NORMAL Mode
Features
Initial Initial even if the Mode is switched.
Settings Settings ● If this settings have been improperly
made a Check Engine Light may go on.
Connecting
The Wires
1. Make settings only after having completed all wiring (connector installation).
2. Make settings with the key in the ON position(engine not running) and the gear in P (Parking) or N (Neutral).
The Product
Installing
Operational Procedure Main Unit Display Area Operational Procedure Main Unit Display Area
Settings
Initial
STOP for 1 second
press the MODE switch
Without braking, until nor appears. Set to
press down twice
100%
this operation.
Make sure to carry out
( 100 Display)
2 Press the UP switch for 10 Blink
seconds or longer to
change the display to “0” . 8 Once the display
changes to 100 release
the accelerator. ( 100 Display)
Press until
“0” appears
or
Count down from 5 to 0 ( nor Display)
after the “cAr” blink.
Speed Pulse
the UP switch.
If the device is re-installed into a different vehicle,
Settings
make sure to carry out these settings again.
Release Voltage Display
(e.g., L1.5) After having finished settings and the bat-
tery or wires have been disconnected it is
not necessary to carry out “Initial Settings”.
4 Pedal is not pressed down.
(Release the accelerator to 0%)
(e.g.)※1
Operate
Check the Settings ※If the display is incorrect start How to
again from step 2 above.
Do not press in on pedal
Voltage Display
0% (e.g., L1.5)
or
Shooting
Trouble-
( 100 Display)
6 Pedal is completely
※Depending on characteristics of the accelerator or on how the
pressed down.
(e.g.)※1 accelerator is stepped on the display may read “A95” (95%).
(Press in on the accelerator to
100%)
If after the “Err” is shown the display returns
to as shown in 4 ( “L1.5” or so on), it means
Voltage Display If is
that the degree of acceleration settings have
100 % (e.g., H4.5) displayed at 7 not been confir med properly. Re-do the
settings from step 4 .
※1 The values shown in the display will vary depending on the type of car.
7
For details about Pulse settings, see the
procedure 4 Speed Pulse Settings “Wiring Chart” .
Before
Using
Setting Completed
4 Press the UP / DOWN
switches to select the
desired pulse setting. (Factory Setting)
If AUTO CRUISE can not be set when the speedom-
Speed Pulse
Settings
Basic Operation
Engine Start
Shooting
Trouble-
Throttle Control
Mode Press the Switching the Change
Press
UP / DOWN Ratio for SPORTS
Press the switch. UP DOWN Mode (SP1 to 7)
MODE switch.
Page 9
MODE Press Press the Switching the Change
Press
UP / DOWN Ratio for ECO
switch. UP DOWN Mode (Ec1 to 5)
Page 10-11
8
Degree of Acceleration Monitor Displays the amount of pressure placed on the
accelerator pedal. (output signal)[15 - 100%, 5% unit]
Before
Using
the ECU where 0 represents the pedal not being pressed in and 100
equals when the pedal is fully pressed down.
※When in ECO Mode, even if the accelerator is stepped on a full 100%
the output signal will only be 80%. Degree of Acceleration While in AUTO CRUISE
※Depending on characteristics of the accelerator or on how the (output) 20% (no degree display)
Features
accelerator is stepped on the display may read up to 95%. (when in
SPORTS Mode and NORMAL Mode only)
USE 1 Check acceleration during ECO driving USE 3 Check control status Press down on pedal.
e.g. 40%
In NORMAL Mode
To e n s u r e r e d u c e d f u e l With the key in the ON position and
-
=
consumption during accelera-
Connecting
under NORMAL Mode press in the
The Wires
tion the degree of acceleration pedal until it reaches 40% (A40), if the 40 %
should be between 15% and 0% Mode is changed to SP7 the display
10 %
100
2 5 % . To f u r t h e r i m p r o v e
results use ECO Mode when
ECO should read 65% (A65) and if placed in
Ec5 the display should change to 20%
wishing to save fuel. (A20). Switch Mode to SP7 Switch Mode to Ec5
[⇒See the above Graph of “Basic
The Product
USE 2 Check acceleration during regular driving
Installing
Control Features” ]
Please use to check the degree of acceleration for any type of ※The actual display may differ slightly.
driving, not just ECO Mode.
Settings
Initial
Switch between three modes: SPORTS Mode (Higher Response), ECO Mode (Lower Response), and
Switch the Mode NORMAL Mode (Standard Performance).
Speed Pulse
1 Key ON.
2 The Mode will change ECO Mode NORMAL Mode SPORTS Mode
Settings
(Engine Start) with each pressing of
the MODE switch.
※For safety, when changing modes always go through (NORMAL) one time.
START MODE Press About the Relay sound
When switching to for safety reasons the relay will go into operation and you
will hear a clicking sound.
Operate
How to
Adjust the Change Ratio for each Mode Switch the change ratios within SPORTS Mode (SP) and ECO Mode (Ec).
When making adjustments to the change ratios, begin at the lowest setting and slowly make changes while continually
checking acceleration.
Shooting
Trouble-
is displayed, the ratio is displayed, the ratio
Press Press
will change with each pressing will change with each pressing
UP DOWN UP DOWN
of the UP / DOWN switch. of the UP / DOWN switch.
Switching the Change Ratio for ECO Mode Switching the Change Ratio for SPORTS Mode
All settings are saved even after the engine has been turned off. However, if the engine is turned off in
Saving Settings
2 seconds or less after the last setting operation was carried out, the settings will not be saved.
【Reference 1】Examples of changes in fuel consumption and 【Reference 2】Basic Control Features
response depending on change ratios
The changes throughout each Mode will be controlled smoothly
SPORTS NORMAL ECO without perceptible steps.
MODE 7 6 5 4 3 2 1 1 2 3 4 5 Acceleration output signal based on amount of
pressure placed on accelerator pedal
Good
Acceleration Output Signal
100
RESPONSE
Bad SP 7
SP7
(at degree monitor)(%)
Good
FUEL 50
EFFICIENCY Ec5
Ec5
Bad
※In ECO Mode, because response is less than the standard fuel efficiency can
be improved. However, if rapid acceleration is purposefully carried out fuel
0 50 100
efficiency will be reduced.
Amount of pressure placed on the accelerator pedal (%)
※The changes in response will be greater as the vehicle’ s power is greater.
9
Operating the AUTO CRUISE
After setting to AUTO CRUISE, you can drive automatically at the set speed even without pressing down on the accelerator pedal.
Before
Using
●AUTO CRUISE is nothing more than an aid to assist drivers. Please make sure
to follow all speed limits and practice safe driving. 【Settable Speed】
●AUTO CRUISE can be dangerous if activated in the following conditions; do not Approximately
use under these conditions. 30 〜140 km/h 120 140
Features
100 160
① On slippery Roads (snow and ice) ② In traffic jams Due to differences in
③ Around sudden curves and/or slopes some standard 80
●Upon climbing a sudden slope, it is not possible to accelerate beyond the capa- meters, the setting 60 0
bility of the engine. Moreover, when going down a sudden decline the engine will fall in the range 40 20
of between 35 and
Connecting
can not force deceleration other than from the engine brake; please use the
The Wires
Mode Setting
Installing
※All settings are saved even after the engine has been turned off.
START
Initial
If you wish not to use AUTO CRUISE, please turn the AUTO CRUISE Mode to OFF.
Operate
How to
5 AUTO CRUISE kicks in at the set speed 【How to Deactivate】 AUTO CRUISE can be deactivated
using any of the following:
When in Acc, do not depress Returns to
●Press the ●Press the ●Press the MODE /
Step 3.
the accelerator for any other
reason than for acceleration. SET switch. brake pedal. AC switch.
Mode Display
MODE Press
Press
/ AC
【How to Accelerate】
① Press down on accelerator pedal to accelerate.
② Take foot off of pedal to return to AUTO CRUISE 【Auto-Deactivation】 Dot lights up
at the set speed. ● When speed declines to 20 km/h or less than the
Accelerate AUTO CRUISE set speed.
● When the speed declines to 15 km/h or less.
Press down on pedal Take foot off pedal 【How to Reset】 After deactivation occurs, carry out as in step 4.
10
Adjust Level
Depending on the size of your car’s engine the amount of time it takes to return to the set cruising speed after a hill climb or other such condition will
differ. By adjusting the level it is possible to change the amount of time for returning to the set cruising speed to be faster or slower to match your
Before
Using
car’ s performance and desired ride.
Level adjustments may differ depending on car model or driving conditions; please use the following as a simple guideline and adjust to
fit your needs. (The factory default setting is L-3)
Quicker L-5 【Setting Examples】
Up to L-5 For Smaller Engines
(Quick Acceleration) In car models with smaller engines, Return Quick (Lessen difference in
L-5 ALTO
Features
to have the car retur n to the set L-4 returning to speed)
50 60
For Smaller L-4 MARCH, FIT, DEMIO,
speed faster raise the level to L-5. 70
Engines WAGON R
40 (Factory Amount of Time to Return to
L-3
Setting) Set Cruise Speed L-3 VOXY, PRIUS, CARAVAN,
Down to L-1 In larger engine car models, to have Slower SERENA, INSIGHT,
(Slow Acceleration) the car ride more comfortably with- Return L-2 Slow (For more comfortable STEP WGN, SWIFT
return to speed)
50 60
For Larger out sudden acceleration to return to 70 L-2 VELLFIRE, CROWN, HIACE,
Connecting
the set speed, lower the level to L-1.
The Wires
Engines 40 L-1 For Larger Engines
ELGRAND, LAGACY, MPV
Operating switches or checking the display while driving may cause accidents; please use with the
utmost consideration for safety.
The Product
Installing
While Running Pressing the switch will display the
1 in AUTO 2 current level and by pressing UP
Change the AUTO CRUISE Level
Settings
Initial
After having carried out all of the necessary wiring and making settings in “Initial
Test Drive Settings” and “Speed Pulse Settings” please carry out a low-speed test run.
●Please carry out the test drive in a safe spacious area away from pedestrians and traffic.
Speed Pulse
●Please make sure to carefully read this manual and understand how to operate the unit before taking a test run.
Settings
Press the AC switch and
1 Engine Start.
2 make AUTO CRUISE Mode
AUTO CRUISE
Possible 3 Settings will be completed
if no operation is done for
on. 3 or more seconds.
START MODE Press
Operate
How to
Start the Test Run
4 5 6 7
AUTO CRUISE Mode: ON Press the SET switch. AUTO CRUISE kicks in at
(35 〜 40 km/h) the set speed
Press
Dot lights up
Shooting
Trouble-
Deactivating AUTO CRUISE AUTO CRUISE does not Operate
● Press the SET switch. ● Poor connection of Gray and Orange wires. (⇒Page 4-5)
● Press the brake pedal. ● Improper wiring of Pink wires. (⇒Page 5)
● Press the MODE / AC switch. ● Respective settings have not been completed. (⇒Page 7 -8)
● Poor connection of SET switch connector (⇒Page 5)
Troubleshooting
Concerning Basic Operations and Car Problems
A Check Engine Light has gone on. The accelerator connector was disconnected Connect to Accelerator Connector(⇒Page 4 - 5 of this
within 15 minutes after having turned the key to Manual) , and turn off the Check Engine Light (⇒Page 12).
OFF.
The “Initial Settings” have not been properly Make the “Initial Settings” (⇒Page 7 of this Manual) , and
carried out. turn off the Check Engine Light (⇒Page 12).
With the key switch in the ON position disconnect Re-connect the disconnected connector and turn off the
Specialized Harness or 6P Connector . Check Engine Light (⇒Page 12 of this Manual).
T h e e n g i n e h a s b e e n tur n e d This product is interlocked with the ECU (engine computer) power. Depending on the model of car, the display
OFF but the display remain on. may remain on for up to 15 minutes even after the engine has been turned off; this is normal.
11
Concerning Basic Operations and Car Problems (Continuation of the previous page)
While making “Initial The “Initial Settings” have not been properly Make the settings by following the directions under
Before
Even if the Mode is changed, the The “Initial Settings” have not been properly Make the settings by following the directions under
changes cannot be felt. carried out. “Initial Settings” found on Page 7 of this Manual.
The Mode and/or the setting of The key was has been turned OFF immediately After having made settings of change ratios or changing the
change ratios can not be saved. after having finished the setting of change ratios Mode, wait for at least two seconds before turning the key
Connecting
While in SPORTS Mode, when put The Pink wire may have been improperly Please reconfirm whether wiring and connections are correct
into reverse the display does not wired or there is a poor connection. or not.
show “bAc”.
The unit is connected to the reverse wire of a Follow the instructions for wiring to reverse found in this
navigation system from another company. Manual (⇒ Page 5).
R
The Product
The backup lights have been changed to LED ●Replace the backup lights with the car maker’s original lights.
Installing
AUTO CRUISE does not Operate. The Gray and Orange wires may have been Please reconfirm whether wiring and connections are
improperly wired or there is a poor connection. correct or not.
The brake lamp bulbs have been changed to LED Replace with standard brake lamp bulbs.
How to
lamp bulbs.
During quick deceleration due to slowness in the gauge it may not operate even though the speed is over 30 km/h.
After AUTO CRUISE is deactivated Brake fuse is burned out. Please reconfirm whether wiring and connections are
the display goes off. correct or not.
The Red and Black wires may have been
Shooting
Trouble-
The “Initial Settings” have not been properly Make the settings by following the directions under
carried out. “Initial Settings” found on Page 7 of this Manual.
AUTO CRUISE will be automatically deactivated if the speed declines to 20 km/h or less than the set speed or if
the speed declines to 15 km/h or less.
When climbing a hill, the speed is The AUTO CRUISE Level has been adjusted to a For details about adjusting see Page 11 of this manual
much slower than the set cruise speed. lower level (lowest is L-1). “Adjust Level” .
It feels like to retur n to the AUTO The AUTO CRUISE Level has been adjusted to a
CRUISE speed is too quick and jumpy. higher level (highest is L-5).
Even at speeds above 30 km/h AUTO “Speed Pulse Settings” have not been properly Make the settings by following the directions under
CRUISE does not kick in. carried out. “Speed Pulse Settings” found on Page 8 of this Manual.
Note
How to Turn Off the Check Engine Light
If the Check Engine Light comes on due to some operational mistake, follow the directions below to turn it off.
① Under normal conditions, start and stop the engine several times.
② If that does not turn off the lamp, disconnect the cable from - terminal of the battery for about 10 minutes. Check Engine
Light is ON
③ If that does not turn off the lamp, please consult your local car dealer and have them turn it off.
※Our products have already been recognized as our Industrial Property or are in the process of receiving Industrial Property status.
※We plan in the near future to take all possible legal measures to protect against unfair competition from look-alike products using similar
designs, regulating characteristics, circuitry and circuitry layout.
※We strictly prohibit the unlicensed use of the PIVOT trademark and the unauthorized use of PIVOT User’ s Manual.
PIVOT CORPORATION 87-3, Shimookada Okada, Matsumoto-shi, Nagano, 390-0313 Japan TEL0263-46-5901 http://pi votj p.c om /
12