Академический Документы
Профессиональный Документы
Культура Документы
The BA823 and BA823F are 8-bit serial input, parallel output drivers. These monolithic ICs were developed as
drivers for thermal printing heads, LED character displays, and other similar applications.
•Thermal
Applications
printing head drivers
LED character display drivers
•1)Features
Can drive up to 200 mA. 4) The digital ground and power ground are separated.
2) Controlling the strobe terminal with the drive timing 5) TTL and CMOS drive possible.
pulse enables current to be reduced when drive is
not being carried out.
3) Using the data output terminal for the next data input
enables cascade connections.
•Block diagram
O0 O1 O2 O3 O4 O5 O6 O7
12 11 10 9 8 7 6 5
16 VCC
STROBE INPUT S 1
C C C C C C C C 13 GND1
14 GND
(Dig)
200
Maximum data transfer speed fMax. 500 — — kHz VIH = 2.0V, VIL = 0.8V —
2
Standard ICs BA823 / BA823F
•Measurement circuits
VCC = 5.0V A
Item SW1 SW2
Data should be left at "0"
ICC 1 1
VIN = 4.5V
IIH 2 1~3
BA823 / F
A
3
2
SW2 1 2 1
PG
SW1
5 4
1 3
6
2 SW1 7
8 SW2 2
1
SW3
PG
1 2
VA
•Input conditions
Data input
D1
Shift pulse
C
t1 t2
Print pulse t3
S
Fig. 4
3
Standard ICs BA823 / BA823F
VCC
1, 2, 15pin
5.5kΩ
10kΩ
20kΩ
5, 6, 7, 8, 9, 10,
11, 12pin
1.0kΩ
12kΩ
(c) Data output circuit
VCC
100Ω
10kΩ
200Ω
500Ω 3pin
5kΩ
Fig.5
750
160
15% 34%
BA823
500 120
Ta = 25°C
BA823F Ta = 75°C
BA823
80
22mA
0 18mA
– 25 0 25 50 75 100 125 150 20 40 60 80 100
AMBIENT TEMPERATURE : Ta (°C) OUTPUT DUTY CYCLE (ALL BIT "ON") (%)
At repetition frequency of 1 Hz or higher
Fig. 6 Power dissipation vs.
Fig. 7 Output conditions
ambient temperature
4
Standard ICs BA823 / BA823F
•Pin descriptions
Pin No. Pin name Code Function
2 SHIFT PULSE C Shift pulse of shift register
15 DATA INPUT DI Data input of shift pulse registered using shift pulse rise
1 STROBE S When "1", the content of the shift register is output
12 OUTPUT O0 "0" when the content of the register is "1" on the 1st bit
11 OUTPUT O1 "0" when the content of the register is "1" on the 2nd bit
10 OUTPUT O2 "0" when the content of the register is "1" on the 3rd bit
9 OUTPUT O3 "0" when the content of the register is "1" on the 4th bit
8 OUTPUT O4 "0" when the content of the register is "1" on the 5th bit
7 OUTPUT O5 "0" when the content of the register is "1" on the 6th bit
6 OUTPUT O6 "0" when the content of the register is "1" on the 7th bit
5 OUTPUT O7 "0" when the content of the register is "1" on the 8th bit
3 DATA OUTPUT DO Has passed the O7 output circuit and becomes the input for the next step
16 VCC VCC Normally 5.0V used (±10%)
13 GND GND1 O0 to O3 output circuit GND
4 GND GND2 O4 to O7 output circuit GND
14 GND GND (Dig) Logic circuit GND
5
Standard ICs BA823 / BA823F
•Timing chart
Clock input C
Data input DI
Strobe input S
O0
O1
O2
O3
O4
O5
O6
O7
Data output DO
Fig.8
6
Standard ICs BA823 / BA823F
O0
O1
O2
O3
O4
O5
O6
O7
O0
O1
O2
O3
O4
O5
O6
O7
O0
O1
O2
O3
O4
O5
O6
O7
BA823 / F BA823 / F BA823 / F
GND1
GND2
GND1
GND2
GND1
GND2
VCC
VCC
VCC
DO
DO
DO
DI
DI
DI
C
C
S
S
Data signal
Shift pulse
Power supply
5V
Print pulse
Fig.9
Example of printing using a strobe pulse current) of the heat element does not need to be
This offers the advantage that the common line (large switched.
•TheCircuit operation
BA823 has the internal configuration shown in the pulse width being the same as that of the strobe input.
logic diagram, with the following three input pins: clock The data output pin DO is used when ICs are connected
C, data DI, and strobe S. Data input is synchronized to in cascade format, and when the output for the last
the clock, with data being read serially at the rising stage of the shift register appears, is connected to the
edge. The content of the set shift register appears at next data input pin DI. When these clock and strobe
output terminals O0 to O7, as shown in the timing chart latches and power switch are used in common, the out-
in Figure 8, depending on the strobe input, with that put pins can be increased by eight bits each.
16 9
6.2 ± 0.3
4.4 ± 0.2
1 8
0.51Min.
0.15 ± 0.1
7.62
1 8
3.2 ± 0.2 4.25 ± 0.3
1.5 ± 0.1
0.3 ± 0.1
0.11
DIP16 SOP16