Академический Документы
Профессиональный Документы
Культура Документы
How to use
DSC-S60/S80/S90/
Acrobat Reader ST80
AEP Model
UK Model
E Model
Hong Kong Model
DSC-S60/S80/S90
Australian Model
Korea Model
DSC-S90
Photo: DSC-S90/Silver Argentine Model
Link
DSC-S60/S80/S90/ST80
—2—
Downloaded from www.Manualslib.com manuals search engine
Table for differences of function
Model DSC-S60 DSC-S80 DSC-S90 DSC-ST80
US, CND, AEP, UK, US, CND, AEP, UK,
AEP, UK, E,
Destination E, AUS, HK, E, AUS, HK, AEP, UK, E, HK
AUS, HK, KR
CH, KR, JE CH, KR, AR, JE
LCD panel size 2.0 type 2.0 type 2.5 type 2.0 type
LCD type (Note) TYPE C TYPE C TYPE C or TYPE S TYPE C
Note: Refer to page 1-4 to discriminate the type of LCD (TYPE C or TYPE S). • Abbreviation
AR : Argentine model
AUS : Australian model
CH : Chinese model
CND : Canadian model
HK : Hong Kong model
JE : Tourist model
KR : Korea model
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
SAFETY CHECK-OUT
1. Check the area of your repair for unsoldered or poorly-soldered Unleaded solder
connections. Check the entire board surface for solder splashes Boards requiring use of unleaded solder are printed with the lead-
and bridges. free mark (LF) indicating the solder contains no lead.
2. Check the interboard wiring to ensure that no wires are (Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
"pinched" or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point : LEAD FREE MARK
them out to the customer and recommend their replacement. Unleaded solder has the following characteristics.
4. Look for parts which, through functioning, show obvious signs • Unleaded solder melts at a temperature about 40°C higher than
of deterioration. Point them out to the customer and ordinary solder.
recommend their replacement. Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
5. Check the B+ voltage to see it is at the values specified.
Soldering irons using a temperature regulator should be set to
6. FLEXIBLE Circuit Board Repairing about 350°C.
• Keep the temperature of the soldering iron around 270°C Caution: The printed pattern (copper foil) may peel away if the
during repairing. heated tip is applied for too long, so be careful!
• Do not touch the soldering iron on the same conductor of the • Strong viscosity
circuit board (within 3 times). Unleaded solder is more viscous (sticky, less prone to flow) than
• Be careful not to apply force on the conductor when soldering ordinary solder so use caution not to let solder bridges occur such
or unsoldering. as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
DSC-S60/S80/S90/ST80
—3—
Downloaded from www.Manualslib.com manuals search engine
TABLE OF CONTENTS
Section Title Page
1. SERVICE NOTE
1-1. Note for Repair ································································ 1-1
1-2. Discharging of The ST-122 Flexible Board’s Charging
Capacitor (C003) ····························································· 1-1
1-3. Note in Lens Frame Installation ······································ 1-2
1-4. Description on Self-diagnosis Display ···························· 1-2
1-5. Method for Copying or Erasing the Data in Internal
Memory ··········································································· 1-3
1-6. Process After Fixing Flash Error ····································· 1-4
1-7. LCD Type Check ····························································· 1-4
2. DISASSEMBLY
2-1. Disassembly ····································································· 2-1
2-2. SY-126 Board Service Position ······································· 2-5
2-3. Removal of Barrier Unit ·················································· 2-7
2-4. Circuit Boards Location ·················································· 2-8
3. BLOCK DIAGRAMS
3-1. Overall Block Diagram (1/2) ··········································· 3-1
3-2. Overall Block Diagram (2/2) ··········································· 3-3
3-3. Power Block Diagram (1/2) ············································· 3-5
3-4. Power Block Diagram (2/2) ············································· 3-7
DSC-S60/S80/S90/ST80
—4—
Downloaded from www.Manualslib.com manuals search engine
1. SERVICE NOTE
1-1. NOTE FOR REPAIR
Make sure that the flat cable and flexible board are not cracked of When remove a connector, don’t pull at wire of connector.
bent at the terminal. It is possible that a wire is snapped.
Do not insert the cable insufficiently nor crookedly.
1 kΩ/1 W
DSC-S60/S80/S90/ST80
1-1
Downloaded from www.Manualslib.com manuals search engine
1-3. NOTE IN LENS FRAME INSTALLATION
When tightening a screw, have both sides of the lens block assembly so as not for the load to depend.
Tapping screw
Lens flame
Self-diagnosis display
• C: ss: ss
You can reverse the camera
malfunction yourself. (However,
contact your Sony dealer or local
authorized Sony service facility
when you cannot recover from the
camera malfunction.)
• E: ss: ss
Contact your Sony dealer or local
authorized Sony service facility.
E:61:ss Checking of lens drive circuit. When failed in the focus and zoom
initialization.
Checking of flash unit or replacement Abnormality when flash is being —
E:91:ss
of flash unit. (Note) charged.
E:92:ss Insert batteries correctly. Batteries are not inserted correctly.
Note: After repair, be sure to perfom “1-6. PROCESS AFTER FIXING FLASH ERROR”.
DSC-S60/S80/S90/ST80
1-2
Downloaded from www.Manualslib.com manuals search engine
1-5. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY
The data can be copied/erased by the operations on the Setup screen. (When erasing the data, execute formatting the internal memory.)
Note: 1 When replacing the SY-126 board, erase the data in internal memory of the board before replacement.
Note: 2 When replacing the SY-126 board or the IC301 on the SY-126 board, execute formatting and initialize the internal memory after
replacement.
Copy
Copying
102_COPY
• Use batteries with enough capacity or the AC Adaptor (not supplied). If you attempt to copy image files
using batteries with little remaining charge, the batteries may run out, causing copying to fail or possibly
corrupting the data.
• You cannot copy individual images.
• The original images in the internal memory are retained even after copying. To delete the contents of the
internal memory, remove the “Memory Stick” after copying, then execute the [Format] command in
Internal Memory Tool.
• You cannot select a folder copied on a “Memory Stick”.
• The setting of (Print order) marks is not copied even when you copy data.
Format
DSC-S60/S80/S90/ST80
1-3
Downloaded from www.Manualslib.com manuals search engine
1-6. PROCESS AFTER FIXING FLASH ERROR
When “FLASH error” (Self-diagnosis Code E : 91 : ** ) occurs, to prevent any abnormal situation caused by high voltage, setting of the
flash is changed automatically to disabling charge and flash setting.
After fixing, this setting needs to be deactivated. Flash error code can be initialized by the operations on the Setup screen.
The LCD type can be discriminated with the mounted parts on the SW-446 board, or the width of flexible harness of LCD panel.
Note: About SW-446 board and LCD panel, discriminate LCD type on the machine, and replace the same type.
Checking method:
1) Refer to “SECTION 2 DISASSEMBLY” to remove the rear cabinet assy.
2) Referring the following figures, each type is discriminated with the mounted parts on the SW-446 board, or the width of flexible cable
of LCD panel.
Rear View (when the rear cabinet assy is removed.) SW-446 Board (Side B)
D006
CA
SH
CA
LCD panel
SH
D004
Narrow:
TYPE C Mounted Parts
TYPE C TYPE S
Wide: TYPE S
D004 — Mount
Width of Flexible Harness of LCD Panel D006 Mount —
DSC-S60/S80/S90/ST80
1-4E
Downloaded from www.Manualslib.com manuals search engine
2. DISASSEMBLY
The following flow chart shows the disassembly procedure.
2-1. DISASSEMBLY 7
4
7 3
6
5
8 1
3
6
7 3
3
0
1
2
3
9
1 Open the BT lid. 5
2 Screw (M1.7) x1
3 Screw (M1.7) x3 6
2
4 Close the BT lid. qa
5 Claw x1 14 Speaker adhesive sheet
5 4
6 Claw x1
7 Claw x3 2 1 Flexible board: CN702 1 Screw (M1.7) x1
8 Cabinet (rear) block 2 Slide the cabinet (upper) to 2 Flexible board of BT001 section
9 Claw x1 upper side and remove claw. HELP
0 Claw x2 3 Claw x1 3 Flexible board of SP901 section
qa Cabinet (front) block 4 Claw x1
Note: Speaker adhesive sheet
5 Cabinet (upper) block
Note: Mic harness is connected. cannot be recycle.
R:1 kΩ/1 W
Line 6 Mic harness: CN703 4 Claw x2 (Part code:
1 5 Claw x2 1-215-869-11)
6 Flexible board: CN701
2 7 MC-153
6
Line
1 Claw x1
2 Claw x1
3 Lift the ST holder.
4 Flexible board of D002 section
to Page 2-3
5 Claw x2
Barrier unit
6 Flexible board of flash unit section
(Refer to page 2-7)
DSC-S60/S80/S90/ST80
2-1 2-2
5 1
2
1 Claw x1
2 Capacitor (C003)
3 Claw x2
4 ST-122
5 Tapping screw x1
6 Claw x2
7 MS-271
DSC-S60/S80/S90/ST80
2-3 2-4
6
5
6 MC-153 flexible
ST-122 flexible
3
3
1 A/V multi cable
(Note)
7
S90 S60/S80/ST80
7 3 BT901
8 1
51
3 7
6
Cabinet (upper) block
4
0 (Control switch block) Lens block
7 12
3 6
9
3
6 8
qa
14 6
5
3
SY-126 board
2
7
4
4
SW-446 board
5
1 3
6
3 5 D901, LCD901
1
2 (Note)
MS-271 board
2 12
5
4 Note: If the A/V multi cable is connected to the multi connector
4 of MC-153 flexible board, the image can not appear on the
LCD screen.
If you want to confirm the circuit of LCD drive or LCD,
disconnect the A/V multi cable.
3
7 4
6 6
3
5
4
1
1 5
3 2
DSC-S60/S80/S90/ST80
2-5 2-6
6 Two screws
(M1.4 × 4.5)
1 Switch on a power supply. 7 Barrier unit
2 Push zoom button and transform the lens SY-126
as shown below. (including CP401 (CH-169 board))
3 Switch off a power supply by taking out a battery
or cut off a power supply from AC daptor. SW-446
(without using camera's power swich)
MS-271
MC-153 flexible
CH-169
4 Pinch A portion with finger
and fit a driver over a hollow. (included in SY-126)
CD-573
3X (included in SY-126)
3X
3X
DSC-S60/S80/S90/ST80
2-7 2-8E
Mic harness
- Top side -
Mic harness
MIC901
- Bottom side -
MIC901
Mic harness
Two claws
DSC-S60/S80/S90/ST80
HELP
Downloaded from www.Manualslib.com manuals search engine
3. BLOCK DIAGRAMS
Link
DSC-S60/S80/S90/ST80
3-1. OVERALL BLOCK DIAGRAM (1/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
C MODEL: S60/S80/ST80/S90(TYPE C)
S MODEL: S90(TYPE S)
Note: About TYPE C/S, please refer to page 1-4
CD-573 BOARD (1/2) SY-126 BOARD (1/2) to discriminate the type of LCD.
LENS BLOCK CP401
CAMERA
CN706
SW-446 BOARD (1/2)
LENS IRIS CH-169 BOARD MODULE PANEL UNIT
(METER) CN001 CN401 K5 G4 H4 (1/2) CN005 (1/2) CN003
(1/2) (1/2) (1/8) D8 D7
Q003 L5 H2 H1
CCD OUT 97 98 100 22 E8 E7 9 25 21
13 BUFFER 24 16 6 60 101 103 104 ı CA AD00 – CA AD13 J1 J2 M5 LCD D0 – LCD D7 ı ı D0 – D7 ı
105 3 2 4 7 35 D6 D5 16 18 28
J4 K4 M6
10 14 18 E6 B4
Q001 K2 K1
E9 22 12 30
IC001 12 LCD HD, LCD VD, LCD CK HSYNC, VSYNC, DCLK LCD901
B8 23 11 31
CA HD
CCD Q002 POWER SAVE 77 45 H5 D9 19 15 29
IMAGER 21 19 37 85 XCS PANEL XCS
W25 28 6 34
SHUTTER ZOOM FOCUS IRIS IC101 CA FD COLOR
15 30 10 5 53 80 46 J5 C MODEL LCD
MOTOR MOTOR MOTOR MOTOR RG, H1B, H2B P ADJ VVCOM
ı 34 6 2 44 CCD SIGNAL F25 6 28 6 PANEL
M M M M 17 38 2 4 48 PROCESSOR,
VCOMH
21 H1A, H2A 32 8 1 37 TIMING 15
S MODEL
22 36 4 3 40 GENERATOR
PANEL AD VR2
7 J22 5 29 37
16 24 9 XSAN RST OUT XRESET
ZOOM 4 V2, V4, V5A, V5B, V6 13 16 91 IC101 29 5 35
FOCUS 27 12 CLKTGO (1/2)
SENSOR 3 ı ı ı 5 6 88 56 47 E1
SENSOR ı 26 8 33
1, 2 1 10 30 15 F2 SAN1 SO, XSAN1 SCK SI, SCLK
CAMERA DSP, CPU 25 9 32
8 17 23 7 11 LENS CONTROL, D901
V1, V3A, V3B XCS FE CN004 BACKLIGHT
6 15 25 10 12 86 39 U22 MODE CONTROL
5 14 26 11 9 (2/8) BL H BL H 6
VHLD 30 4
89 40 5
10 19 21 20 72 SAN1 SO, XSAN1 SCK
VST 93 41 BL L BL L 2
9 18 22 19 76 32 2
SHT SHT 1
19 5 35 21 82 XSAN RST OUT
92 42
20
Q401 36 87
Q004 VSUB CONT
7 33 BL L
OVERALL (2/2)
VSUB CONT PRE
R23 XSAN RST OUT
BL H 1 (PAGE 3-4)
AF4
IC601 U2
SAN1 SO, XSAN1 SCK SAN1 SO, XSAN1 SCK
XCAM DR PS R6
(3/8) G7 P21
IC103
CN601 FC EN,
A6 C8 FC DIR A,
21 FOCUS L4 SAN VOUT V LINE OUT
FOCUS A, A, B, B ı B5 B8 FC DIR B H26 4 VIDEO AMP 2
MOTOR L2 VIDEO AMP ON
24 A4 C7 U23 1 (2/8)
DRIVE N5
B4 B7
SAN AUOUT
ZM EN, K26
SAN AUIN
C1 ZOOM B3 ZM DIR A, L26
1 N2 XAU LINE MUTE
ZOOM A, A, B, B D2 MOTOR B2 ZM DIR B T23 OVERALL (2/2)
ı N6
4 E1 DRIVE A2
M2 Y26
XCS AUDIO 2 (PAGE 3-3)
E2 A1
AC1
G4 USB DP, USB DM
G1 IRIS S EN, IRIS S IN, R2 AD1
10 H4 IRIS IRIS M EN, IRIS M IN USB DPULLUP
IRIS S±, M± ı G2 P6 T5
G5 MOTOR
13 DRIVE H2 N4
H6 G3 P4 USB VBUS
Q101
11 6 2
ı ı ı
MS BS, MS D0 – MS D3, MS CLK MS BS, MS D0 – MS D3, MS CLK 8 9 BS, DATA0 – DATA3, SCLK 5
MEMORY
6 11 7 STICK
5 12 8
XMS IN INT
7 10 6
V LINE OUT
CN703 MIC901
SAN AUIN MIC SIG
E6 B6 2
IC502 A5
SAN AUOUT A2
E5
OVERALL (1/2) AUDIO AMP
(PAGE 3-2) 2 (6/8) D1
CN701 MC-153 FLEXIBLE BOARD
F3
SAN1 SO, XSAN1 SCK
E3 SP ± 42 SP ± SP901
44 SPEAKER
XAU LINE MUTE
F1
XCS AUDIO
E4 V OUT V OUT
6 26
AU OUT A OUT
4 30
XAV JACK IN XAV JACK IN
2 31
12 22
USB DP, USB DM D± D±
14 20
USB VBUS USB VBUS USB VBUS
16 16
XAV JACK IN
U25
J23 KEY AD1 C, KEY AD2 C KEY AD1 C, KEY AD2 C 10 KEY AD1 C, KEY AD2 C 29
G25 9 27
X102 XMULTI IN XMULTI IN XMULTI IN CN002
A6 R21 8 25 MULTI
A : VIDEO SIGNAL 12MHz
Q703 CONNECTOR
A : AUDIO SIGNAL XACV IN XACV IN XACV IN
V25 7 23
A : VIDEO/AUDIO SIGNAL
CRADLE ON CRADLE ON
45 21
X K.BATT
17 14
IC101 V TH
18 12
(2/2)
28 ACV UNREG 2
ı
FRONT CONTROL 34 4
(2/8) 35 BATT UNREG 1
ı
XMS IN 39 3
B10 V BATTT
USB VBUS 40 5
CD-573 BOARD (2/2) C9 VL 3V
1 BT001
CN001 CN401 LITHIUM
BATT TMP
IC001
X K.BATT
X001
D002 32.768kHz
FLASH/ XSTRB LED A8
DC/DC MS-271 BOARD (2/2)
RECORDING 3 37 E22 CONVERTER CN705 CN004
(7/8) (2/2) (2/2) TH001
BATTERY
ST UNREG 16 1
TEMP SENSOR
PANEL 15V S001
SW-446 BOARD (2/2) EVER 2.8V BATTERY
15 2 INSERTION
MS VCC DETECT
CN005 CN706
(2/2) (2/2) D 3.2V
A 3.2V CAM –7.5V
D008 XACCESS LED
(MS ACCESS) 33 1 E4 CN001
CAM 2.9V Q007,
D 1.8V 008 4 BATT UNREG
S001 – 008, +
CAM –7.5V 3 BT901
010, 011
CAM 15V BATTERY
FUNCTION 1 33 KEY AD 0, 1 K23 B8 TERMINAL
M 5V 2 BATT GND
KEY 3 31 L23 −
D 1.2V 1
H1
BATT SENS
K25 G5
MS PWR ON
T25 D3
XCS DD
CONTROL SWITCH BLOCK W23 A6
S001 AA5 C6
(SHUTTER) AB5 SAN0 SI, SAN0 SO, XSAN0 SCK C5
CN702 Y5 B6
4
XAE LOCK SW
N21 XDD RST OUT E9
BL H 1
R26 A7 BL L
XSHTR SW F9 OVERALL (1/2)
5 P23 Y4
XPWR OFF (PAGE 3-2)
AA23 B7
05
DSC-S60/S80/S90/ST80
3-3 3-4
LDO3IN B2
CAM 2.9V
LDO3 A2
BATT TMP
X K.BATT
L003
MS-271 BOARD LX2 C10
D 1.2V
S001 IC001
BATTERY POWER 2
INSERTION 2 15 DC/DC A (PAGE 3-7)
DETECT CONVERTER IC002
(7/8) 15V/–7.5V REG
(7/8)
CN002 Q004
MEMORY VCC MS VCC CAM –7.5V
STICK 9 16 1 PWR56OUT1 J7 SWITCHING 3 VEE REG3 4
PWR56OUT2 K7 STB 1
CAM 15V
7 VCC REG2 6
L006
LX5-1 J9
LX5-2 J10
LX5-3 K9
LX5-4 K10
D003
EVER 2.8V
VO5 H10
MS VCC
VFB5 H9
GT6 H6
VFB6 H7
L010
G2 MS PWR MS PWR IN G1
XACV IN MS PWR ON
V25 IC101 T25 D3 MS PWR ON
(1/2)
Q002, 003
CAMERA BATT SENS L008 M 5V
DSP, K25 G5 UNREGMON SWITCHING
XCS DD Q001
CPU, W23 A6 CE
LENS AA5 C6 SO BG4 G9 DC CONTROL
CONTROL, AB5 SAN0 SI, SAN0 SO, XSAN0 SCK C5 SI
MODE Y5 B6 SCLK TG4 F10
CONTROL, XDD RST OUT
FRONT R26 A7 XRESET PSG4 G8
CONTROL Y4 VFB4 F7
XPWR OFF
(2/8) AA23 B7 XPWROFF
–7.5V ON
P25
05
DSC-S60/S80/S90/ST80
3-5 3-6
C MODEL: S60/S80/ST80/S90(TYPE C)
SW-446 BOARD S MODEL: S90(TYPE S)
D008
(MS ACCESS) Note: About TYPE C/S, please refer to page 1-4
SY-126 BOARD (2/2) to discriminate the type of LCD.
PANEL UNIT
CN706 CN005 CN003
L001
D 3.2V VDD
2 32 17 LCD901
Q001, 002
C MODEL DC CONTROL COLOR
LCD
L002 PANEL
PANEL 15V VDC
4 30 15
D901
CN004 BACKLIGHT
BL H BL H BL H 6
30 4
5
BL L BL L BL L 2
32 2
1
PANEL 15V
D 3.2V D 3.2V
CONTROL SWITCH BLOCK
CN702
A 3.2V D001
9
L001 (POWER)
A 3.2V A 3.2V
2 A 3.2V
IC301
32M AND FLASH
(5/8)
POWER 2 FB201
(PAGE 3-6) A D 1.8V IC201 CP401
CAMERA MODULE
FB202 32M BURST (1/8)
FLASH
(4/8)
CH-169 BOARD
L201
L403 FL401
D 3.2V 54
55
FL201 IC203
71
128M SDRAM
FB403
(4/8)
56
IC101
L404
CAM 2.9V CAM 2.9V 53 CCD SIGNAL
57 PROCESSOR,
L402
D 1.2V TIMING
52
GENERATOR
FB401
CAM –7.5V CAM –7.5V
49
FB402
CAM 15V CAM 15V
51
M 5V M 5V
IC503
2.8V REG CD-573 BOARD
(6/8) IC502 CN401 CN001
A 3.2V AUDIO AMP L401
CAM 15.0V CD 12 28 IC001
4 VDD VOUT 1 (6/8)
13 27 FB001
CAM –7.5V CD CCD IMAGER
32 8
D 3.2V D001
L104 IC103 39 1
(AE/AF LOCK)
VIDEO AMP D002
(2/8) FLASH/
RECORDING
IC601
A 3.2V
LENS DRIVE
M 5V (3/8)
VI 3.2V
IC101
AU 3.2V (2/2)
LENS BLOCK
CAMERA
A 3.2V DSP, Q601 CN601
CPU, D 3.2V F RST VCC ZOOM
FOCUS
20
SD 3.2V LENS SENSOR
CONTROL,
MODE XZM RST LED XZM RST LED
D 3.2V CONTROL, B3 Z RST VCC1 ZOOM
9
Z RST VCC2 SENSOR
L101 FRONT 25
CONTROL 1, 2
D 1.2V
(2/8)
L102
05
DSC-S60/S80/S90/ST80
3-7 3-8E
LITHIUM
BATTERY
SPEAKER
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
D-
DSC-S60/S80/S90/ST80
D+
NC
V_TH
V_OUT
A_OUT
V_GND
A_GND
X_K.BATT
ACV_GND
ACV_GND
USB_GND
USB_GND
USB_VBUS
ACV_UNREG
ACV_UNREG
CN002 32P
(MULTI CONNECTOR)
05
MC-153
TO AV/USB MULTI CABLE OR CRADLE
(MULTI CONNECTOR)
FLEXIBLE BOARD
XMULTI_IN
BATT_UNREG
BATT_UNREG
V_BATT
XAV_JACK_IN
NC(UART_SO)
NC(UART_SI)
NC
ACV_GND
XCAM_IN
NC(XLANC_PWR_ON)
X_CGH_ON
CRADLE_ON
XACV_IN
KEY_AD2_C
KEY_AD1_C
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
4-1. FRAME SCHEMATIC DIAGRAM
BT901
BATTERY
TERMINAL
MIC
MIC901
4
3
2
1
1
2
9
8
7
6
5
4
3
2
1
4-1
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
D-
D+
NC
NC
SP-
SP+
V_TH
VL_3V
V_OUT
V_GND
A_GND
V_BATT
AU_OUT
XACV_IN
CN001 4P
X_K.BATT
MIC_GND
MIC_SIG
ACV_GND
ACV_GND
ACV_GND
ACV_GND
ACV_GND
ACV_GND
ACV_GND
ACV_GND
ACV_GND
CN703 2P
USB_GND
USB_GND
BATT_GND
BATT_GND
USB_VBUS
XMULTI_IN
X_CGH_ON
CN701 45P
KEY_AD1_C
KEY_AD2_C
CRADLE_ON
ACV_UNREG
ACV_UNREG
ACV_UNREG
ACV_UNREG
ACV_UNREG
ACV_UNREG
ACV_UNREG
BATT_UNREG
BATT_UNREG
BATT_UNREG
BATT_UNREG
BATT_UNREG
BATT_UNREG
BATT_UNREG
XAV_JACK_IN
D_3.2V 14
XAF_LED 13
ST_5V 12
CN702 10P
STRB_CHG 11
1 MODE_DIAL1
XSTRB_FULL 10
2 A_3.2V
STRB_CHG_CONT 9
3 MODE_DIAL0
STRB_ON 8
4 XAE_LOCK_SW
ST_GND 7
5 XSHTR_SW
ST_GND 6
6 REG_GND
ST_GND 5
ST-122
7 N.C.
MEMORY STICK
ST_GND 4
BOARD
8 XPWR_ON
FLEXIBLE
(FLASH DRIVE)
BLOCK
ST_UNREG 3
9 A_3.2V
SWITCH
ST_UNREG 2
STICK
CONTROL
10 XPWR_LED
MEMORY
ST_UNREG 1
12
11
CN401 39P CN001 39P
9
8
7
6
5
4
3
2
1
10
GND 1 39 GND
CN004 16P CN705 16P H2B 2 38 H2B
BS
INT
VSS
VCC
VSS
SCLK
MS_VCC 16 1 MS_VCC GND 3 37 GND
DATA3
DATA2
DATA1
REG_GND 15 2 REG_GND H2A 4 36 H2A
CN002 10P
SDIO/DATA0
REG_GND 14 3 REG_GND GND 5 35 GND
REG_GND 13 4 REG_GND H1B 6 34 H1B
CP401
MS_CLK 12 5 MS_CLK GND 7 33 GND
PROCESS
MS_D3 11 6 MS_D3 H1A 8 32 H1A
BOARD
CCD SIGNAL
CH-169
XMS_IN 10 7 XMS_IN GND 9 31 GND
MS_D2 9 8 MS_D2 RG 10 30 RG
MS_D0 8 9 MS_D0 GND 11 29 GND
CCD
FP-199
MS_BS 6 11 MS_BS CAM_15.0V_CD 13 27 CAM_15.0V_CD
FLEXIBLE
REG_GND 5 12 REG_GND GND 14 26 GND
BOARD
MS-271
CONNECTOR
REG_GND 4 13 REG_GND GND 15 25 GND
MEMORY STICK
REG_GND 3 14 REG_GND CCD_OUT 16 24 CCD_OUT
X_K.BATT 2 15 X_K.BATT GND 17 23 GND
BATT_TMP 1 16 BATT_TMP GND 18 22 GND
POWER_SAVE 19 21 POWER_SAVE
GND 20 20 GND
VHLD 21 19 VHLD
VST 22 18 VST
CN003 39P CN005 33P CN706 33P V1 23 17 V1
39 VCOM KEY_AD0 1 33 KEY_AD0 V2 24 16 V2
FP-201 FLEXIBLE
V5A
(CCD IMAGER)
23 D2 REG_GND 17 17 REG_GND
(7/8) (DC/DC CONVERTER)
22 D1 D7 18 16 D7
2.5 INCH
2.0 INCH
CN601 27P
21 D0 D6 19 15 D6
(4/8) (BURST FLASH, SDRAM)
Z_RST_SENS2 27
20 VBC/NC D5 20 14 D5
:S90
Z_RST_GND2 26
19 VSH/VS D4 21 13 D4
FP-200 FLEXIBLE
Z_RST_VCC2 25
18 VCOMDC D3 22 12 D3
FOCUS_A 24
:S60/S80/ST80
17 VDD D2 23 11 D2
LCD901
FOCUS_B 23
16 NC/VR D1 24 10 D1
FOCUS_A 22
15 VDC/VCOMH D0 25 9 D0
4-2
FOCUS_B 21
14 NC REG_GND 26 8 REG_GND
F_RST_VCC 20
SW-446 BOARD
13 NC/VGH REG_GND 27 7 REG_GND
F_RST_GND 19
12 NC//VGL P_ADJ 28 6 P_ADJ
F_RST_SENS 18
11 C2+ PANEL_AD 29 5 PANEL_AD
5 NC/C1+
BLOCK
IRIS_S_+ 11
4 NC/C1-
IRIS_S_- 10
B: S MODEL
A: C MODEL
3 VSS
Z_RST_VCC1 9
2 NC/TFTCOM
Z_RST_SENS1 8
1 NC/VCOM
Z_RST_GND1 7
TEMP_OUT 6
CN004
TEMP_GND 5
Note: Pinname A/B of CN003 and CN005
ZOOM_A 4
BL_L
BL_L
N.C.
N.C.
BL_H
BL_H
6P
ZOOM_B 3
1
2
3
4
5
6
ZOOM_B 1
C MODEL: S60/S80/ST80/S90(TYPE C)
FRAME
4-2. SCHEMATIC DIAGRAMS
Link
MC-153 FLEXIBLE BOARD
CD-573 BOARD (CCD IMAGER) (MULTI CONNECTOR)
SW-446 BOARD
(CONTROL SWITCH, LCD PANEL) MS-271 BOARD (MEMORY STICK CONNECTOR)
DSC-S60/S80/S90/ST80
Magenta
White
Cyan
• B: B– Line Green
Red
• J : IN/OUT direction of (+,–) B LINE.
Blue
• C: adjustment for repair.
• A: not use circuit
• Circled numbers refer to waveforms.
(Measuring conditions voltage and waveform)
• Voltages and waveforms are measured between the
measurement points and ground when camera shoots A B A=B B A
color bar chart of pattern box. They are reference values Fig. a (Video output terminal output waveform)
and reference waveforms.
(VOM of DC 10 MΩ input impedance is used) Electronic beam
• Voltage values change depending upon input scanning frame
impedance of VOM used.)
CRT picture frame
Precautions for Replacement of CCD Imager
• The CD-573 board mounted as a repair part is not equipped
with a CCD imager.
When replacing this board, remove the CCD imager from
the old one and mount it onto the new one. Fig.b (Picture on monitor TV)
• If the CCD imager has been replaced, carry out all the
adjustments for the camera section. When indicating parts by reference number, please
• As the CCD imager may be damaged by static electricity include the board name.
from its structure, handle it carefully like for the MOS IC.
In addition, ensure that the receiver is not covered with The components identified by mark 0 or dotted line with
dusts nor exposed to strong light. mark 0 are critical for safety.
Replace only with part number specified.
DSC-S60/S80/S90/ST80
4-5
Downloaded from www.Manualslib.com manuals search engine
For Schematic Diagram
• Refer to page 4-37 for printed wiring board.
1 2 3 4 5 6 7 8 9
FB001
B
D001
SML-510MWT86
CN001 39P (AE/AF LOCK)
D_3.2V 1
XAE_LOCK_LED 2
XSTRB_LED 3
D002
GND 4 SML-310YTT86
C SHT 5
FLASH
/RECORDING
GND 6
VSUB_CONT 7 R003
2200
CAM_-7.5V_CD 8 Q002
DTC144EMT2L
GND 9 SWITCH
12 11 10 9 8 7 6 5 4 3 2 1
V6 10
GND
GND
V HOLD
V ST
V1
V2
V 3A
V 3B
V4
V 5A
V 5B
V6
V5B 11
R004 C004
3300 XX
V5A 12
D 16V
V4
V3B
13
14
IC001
Q001 R005 C005 CCD IMAGER
V3A 15 DTC144EMT2L 3900 XX IC001
SWITCH ICX488DQF-13
V2 16
V OUT
C sub
H 1B
H 2B
H 1A
H 2A
GND
GND
VDD
SUB
RG
SY-126 R002
VL
V1 17
22k
(1/8) VST 18
CN401 13 14 15 16 17 18 19 20 21 22 23 24
VHLD 19
THROUGH THE
FP-201 FLEXIBLE GND 20
E PAGE 4-11
of LEVEL3
POWER_SAVE 21
Q003
2SC39320S2S0
BUFFER
GND 22
GND 23
CCD_OUT 24
R007 C003 C006
GND 25 56 0.1u 0.1u
16V 16V
GND 26
C008 C009
CAM_15.0V_CD 27 0.1u XX
16V 16V
F CAM_15.0V_CD 28
R001
C001
0.1u
GND 29 0 16V
RG 30
GND 31
H1A 32
GND 33
H1B 34
GND 35
H2A 36
GND 37
R006
H2B 38 1300
G GND 39
Q004 C007
DTC144EMT2L 0.1u
SWITCH 16V
05
DSC-S60/S80/S90/ST80
4-7 4-8 CD-573
DSC-S60/S80/S90/ST80
1 2 3 4 5 6 7 8 9 10 11 12 13
XX MARK:NO MOUNT
NO MARK:REC/PB MODE
LND001 STATIC_GND
1
VMZ6.8NT2L
MAZS130008SO
R047
MAZS220008S0
0
D003
D010
D009
B 3 2 S003 S008
T (ZOOM)
S011
W
4 (SET) 3 4 3 2 1 1 2
S005 4 3
6 5
8 7
2 1 3 4
2 1 (REVIEW)
1 4 3 RB002
2 1 2 2200
4 3 4 3
6 5
8 7
3 4 2 1 S010
S007
2 S002 1 RB001
2200 MENU IMAGE SIZE
1 2 /DELETE
4 3 1 2
C (FLASH)
4 3 3 S004 4
3 4
2 1
S006
2 S001 1 (MACRO) CN004 6P
DISPLAY/
LCD ON/OFF 1 BL_L D901
BACKLIGHT
2 BL_L
(SELF TIMER)
3 N.C.
KEY_AD0 1 5 BL_H
D BL_L 2 6 BL_H
KEY_AD1 3 CN003 39P
BL_H 4 39 VCOM
XRESET 5 38 NC/TFTCOM
XCS 6 37 VR2
REG_GND 7 36 VSS
SI 8 C007 35 XRESET
XX 50V
SCLK 9 34 XCS
E REG_GND 10 33 SI
VSYNC 11 32 SCLK
HSYNC 12 31 VSYNC
REG_GND 13 30 HSYNC
F FP-200 FLEXIBLE
PAGE 4-26
REG_GND
D7
17
18
26
25
D5
D4
of LEVEL3 LCD901
D6 19 24 D3 COLOR
LCD
D5 20 23 D2 PANEL
D4 21 22 D1
D3 22 21 D0
R005
D2 23 560k 20 VBC
R041 10
D1 24 R002 C010 19 VSH 2.0 INCH
XX 2.2u 10V
R045 R004 10k :S60/S80/ST80
L001 22k
D0 25 18 VCOMDC
G REG_GND 26
10uH
17 VDD
2.5 INCH
:S90
C MODEL
D4 21 22 D1
D3 22 21 D0
R005
D2 23 XX 20 NC
R041 0
D1 24 R002 C010 19 VS 2.0 INCH
J D0 25
L001
10uH
R045
10k
0 2.2u 6.3V
R004 56k
18 VCOMDC
:S60/S80/ST80
2.5 INCH
REG_GND 26 17 VDD :S90
S MODEL
05
DSC-S60/S80/S90/ST80
4-27 4-28 SW-446
1 2 3 4 5 6 7 8 9 10
NC
NC
NC
VBATT
ST_5V C004
2
CAPACITOR
12
0.047u
LND013 13 XAF_LED 4.2 250V
10 11 12
1
SW PGND
LND014 14 D_3.2V
IC002
2
SW PGND
D002 5 0 XE_K(L)
OPY5252
3
D
G_IGBT
I_PEAK
NC
NC
5 6 7 8
0 0 269
Q001
CY25BAJ-8F-T23
FLASH DRIVE
R002 0
4.7M
C002 C006
E 1u 0.1u R003
33
±0.5%
05
The components identified by mark 0 or dotted Les composants identifiés par une marque 0 sont
line with mark 0 are critical for safety. critiques pour la sécurité. Ne les remplacer que
Replace only with part number specified. par une piéce portant le numéro spécifié.
DSC-S60/S80/S90/ST80
4-29 4-30 ST-122
1 2 3 4 5 6 7 8 9 10
BT001
LITHIUM
BATTERY
LND001 1 VL_3V
LND002 2 XAV_JACK_IN
B LND003 3 A_GND
LND004 4 AU_OUT CN002
32P
LND005 5 V_GND (MULTI CONNECTOR)
TO AV/USB MULTI CABLE OR CRADLE
LND006 6 V_OUT FB001
LND007 7 XACV_IN 32 A_GND XAV_JACK_IN 31
C LND011
LND012
11 USB_GND
1 3
24 USB_GND XACV_IN 23
21
12 D+ LF001 22 D+ CRADLE_ON
145658321 19
LND013 13 NC 2 4 20 D- X_CGH_ON
LND014 14 D- 18 USB_GND NC(XPWR_ON_P) 17
D SY-126
LND019 19 ACV_GND 8 ACV_GND NC 7
LND023 23 ACV_GND
LND024 24 ACV_GND
LND025 25 ACV_GND
LND026 26 ACV_GND
E LND027
LND028
27 ACV_GND
28 ACV_UNREG
LND029 29 ACV_UNREG
LND030 30 ACV_UNREG 3 3
LND031 31 ACV_UNREG
1 1
LND032 32 ACV_UNREG 2 2
D001
MAZS068008SO LND048
LND033 33 ACV_UNREG
STATIC_GND
LND034 34 ACV_UNREG D002 D003 R003
F LND035 35 BATT_UNREG
VMZ6.8NT2L VMZ6.8NT2L 0
LND036 36 BATT_UNREG
LND037 37 BATT_UNREG
LND038 38 BATT_UNREG
LND039 39 BATT_UNREG
LND040 40 V_BATT
LND041 41 N.C. LND046
LND042 42 SP+ SP+
SP901
G LND043 43 X_CGH_ON SP-
LND047
SPEAKER
LND044 44 SP-
LND045 45 CRADLE_ON
05
The components identified by mark 0 or dotted Les composants identifiés par une marque 0 sont
line with mark 0 are critical for safety. critiques pour la sécurité. Ne les remplacer que
Replace only with part number specified. par une piéce portant le numéro spécifié.
DSC-S60/S80/S90/ST80
4-31 4-32 MC-153
1 2 3 4 3 4 1 2 3 4 5
4
S002
D POWER
2
1
05
(POWER)
D001
XSHTR_SW
E
XPWR_LED
A_3.2V
XPWR_ON
N.C.
REG_GND
XAE_LOCK_SW
MODE_DIAL0
A_3.2V
MODE_DIAL1
10
8
7
6
5
4
3
2
1
LND009
LND008
LND007
LND004
LND001
LND010
LND006
LND005
LND003
LND002
F
SY-126
(7/8)
CN702
PAGE 4-23
of LEVEL3
05
DSC-S60/S80/S90/ST80
4-33 4-34 MS-271, CONTROL SWITCH BLOCK
Link
DSC-S60/S80/S90/ST80
4 1
DSC-S60/S80/S90/ST80
4-35
Downloaded from www.Manualslib.com manuals search engine
CD-573
Note for Printed Wiring Board (See page 4-35).
D002
D002
FLASH/
A RECORDING
K A
A
R003
R004
Q001
Q004
B
C004
C
R006
E
B E
C007 C
C
B E
Q002
CN001
R002
R007
R005 12 1
Q003
C C
E
C
FB001
B
C005
C003
R001
IC001 +
38
C009 B
39
C001
C008
13 24
C006
D D
1-866-280- 11 21 1-866-280- 11 21
05
1 2 3 05
3 2 1
DSC-S60/S80/S90/ST80
4-37 4-38 CD-573
DSC-S60/S80/S90/ST80
4
2
S008
S011
CN004
1
A A
2
6 1
S011 S008
W (ZOOM) T
C010
R047
R005
R041
R043
+ C016 A
+ C018 A
R009
C005
+ C017 A
S006
1
D005
C012
R004
DISPLAY/
D006
S006
LCD ON/OFF C003
R002
A C015 + R040 R008
3
C009 LND001
Q002
R046
D010
D009
Q001
B B
ECB C006
R039
A C014 +
D004
C
B E
C004
2 8
R035 R034
C011
RB002
A C013 + 1 7
A C001 + S007 2 8
1
D003 3 1 2
2
MENU RB001
S002
R045
C002
R036
R033
R032
R044
1 7
L002
C007
3
C008 L001
R037 R038
(FLASH)
S007
CN005
4
1
S002
S005 S004
2
1
C C
32
33
(REVIEW) (MACRO)
3
1
2
S003
S005
S004
39
38
S003
4
3
1
S010 (SET)
4 2
IMAGE SIZE/
DELETE
CN003
S001
2
D 3 1 D
S010
R029
S001
D008
(MS ACCESS)
4
K A
(SELF TIMER) D008
2
1-866-279- 11 21
1-866-279- 11 21
05
1 2 05
2 1
DSC-S60/S80/S90/ST80
4-41 4-42 SW-446
A
C003
CHARGING FLASH UNIT
CAPACITOR C002 XE A(H) XE K(L)
R003
1
4
16
5
R002
17
5 TRIGGER
8
13
8
12
9
4
Q001
L001
IC002
C003
B
R004
T001
2
C004
1 4 1
C001
D001
C006
K A
5
1
LND001
LND002
LND003 LND017 LND018
LND004
LND005
LND006
LND007 2
LND008 LND019
LND009 L002
LND010 1 3
LND011
LND012
LND013
LND014
14
C >PI<
ST-122
1-866-281-
1-866-281- 11 21
05
1 2 3 4 5 6 7 8
LND045
LND043
LND041
LND039
LND037
LND035
LND033
LND031
LND029
LND027
LND025
LND023
LND021
LND019
LND017
LND015
LND013
LND011
LND009
LND007
LND005
LND003
LND001
45 1
supplied, but this is included in
SP901
LND044
LND042
LND040
LND038
LND036
LND034
LND032
LND030
LND028
LND026
LND024
LND022
LND020
LND018
LND016
LND014
LND012
LND010
LND008
LND006
LND004
LND002
BATTERY, MC-153 flexible complete board. SPEAKER
LITHIUM SECONDARY SP–
LND047
LND048
1
2
CN002
(MULTI CONNECTOR) CN002
LF001
3 4
1 2
BT001
31
FB002 R006
32
D003
FB001
213
D002
MC-153-
MC
C 1
153
3 >PI<
PI<
213
D001
R003
1-866-282- 11 21
05
DSC-S60/S80/S90/ST80
4-43 4-44 ST-122, MC-153
FB001
FB002
FB003
FB004
R004
10 TH001
1
16
CN004
CN002
1
MEMORY
STICK
1
S001
BATTERY
S001
INSERTION DETECT
3
11 12
LND001
1-866-278- 11 21 1-866-278- 11 21
05 05
DSC-S60/S80/S90/ST80
4-45 4-46 MS-271
DSC-S60/S80/S90/ST80
CN001 C-1
* D001 A-1
* D002 A-1
FB001 C-3
IC001 C-2
Q001 C-1
Q002 C-2
Q003 C-1
Q004 C-1
R001 C-1
R002 C-1
R003 C-2
R004 C-2
R005 C-1
R006 C-1
R007 C-1
DSC-S60/S80/S90/ST80
4-50 CD-573
Downloaded from www.Manualslib.com manuals search engine
Mounted parts location of the SY-126 board is not shown.
Page 4-51 is not shown.
DSC-S60/S80/S90/ST80
no mark : side A
* mark : side B
SW-446 BOARD ST-122 FLEXIBLE BOARD
C001 B-2 C001 B-5
C002 B-2 C002 A-3
* C003 B-1 C003 A-1
* C004 B-1 C004 B-3
* C005 A-1 C006 B-5
* C006 B-1
C008 B-2 D001 B-3
C009 B-2 D002 A-8
* C010 A-1
* C011 B-1 IC002 B-3
C012 B-2
C013 B-1 L001 B-5
C014 B-1 L002 B-7
C015 B-1
Q001 B-3
CN003 D-2
CN004 A-2 R002 B-3
CN005 C-1 R003 B-3
R004 B-3
* D003 B-1
* D004 B-1 T001 B-4
* D005 B-1
* D006 B-1
* D008 D-1
* D009 B-1
* D010 B-1
L001 B-2
L002 B-1
Q001 B-2
Q002 B-2
* R002 B-1
* R004 B-1
* R005 A-1
* R008 B-1
* R009 B-1
* R029 D-1
R032 B-2
R033 B-2
R034 B-2
R035 B-2
R036 B-2
R037 B-1
R038 B-2
R039 B-2
R040 B-2
* R041 A-1
* R043 A-1
R044 B-2
R045 B-2
* R046 B-1
* R047 A-1
* RB001 B-1
* RB002 B-1
* S001 D-1
* S002 C-2
* S003 C-2
* S004 C-1
* S005 C-2
* S006 B-2
* S007 C-2
* S008 A-1
* S010 D-2
* S011 A-2
DSC-S60/S80/S90/ST80
4-52E SW-446, ST-122
Downloaded from www.Manualslib.com manuals search engine
NOTE
A B C
DSC-S60/S80/S90/ST80
NOTE:
• -XX, -X mean standardized parts, so they may have some differences from When indicating parts by reference number,
the original one. please include the board name.
• Items marked “*” are not stocked since they are seldom required for routine
service. Some delay should be anticipated when ordering these items. The components identified by mark 0 or
• The mechanical parts with no reference number in the exploded views are not dotted line with mark 0 are critical for safety.
supplied. Replace only with part number specified.
• Due to standardization, replacements in the parts list may be different from Les composants identifiés par une marque
the parts specified in the diagrams or the components used on the set. 0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
• CAPACITORS:
le numéro spécifié.
uF: µF
• COILS
uH: µH
• RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable
• SEMICONDUCTORS
In each case, u: µ, for example:
uA...: µA... , uPA... , µPA... ,
uPB... , µPB... , µPC... , µPC... ,
uPD..., µPD...
• Abbreviation
AR : Argentine model
AUS : Australian model
CH : Chinese model
CND : Canadian model
HK : Hong Kong model
JE : Tourist model
KR : Korean model
Swedish
Portugal
Chinese
Chinese
German
Spanish
Russian
English
Korean
French
Arabic
Italian
Dutch
Area
GP1 J z z
US
CND
GP2 z z z z z z
AUS
Vietnam
AEP
GP3 z z z z z z z z z
UK
E
AR
GP4 z z z z z z
BR
TW
JE
HK
GP5 z z z z z z
CH
KR
DSC-S60/S80/S90/ST80
5-1
Downloaded from www.Manualslib.com manuals search engine
5. REPAIR PARTS LIST
5 6
MIC901
4 3
7
8
ns
Ref. No. Part No. Description Ref. No. Part No. Description
1 X-2055-111-1 CABINET FRONT ASSY (630C) (S90: SILVER) 5 X-2055-120-1 CABINET (UPPER) ASSY (630D) (S90: BLUE)
1 X-2055-118-1 CABINET FRONT ASSY (630D) (S90: BLUE) 6 X-2055-123-1 CABINET (REAR) ASSY (240) (ST80)
1 X-2055-115-1 CABINET, FRONT, ASSY (620) (S60/S80/ST80) 6 X-2055-122-1 CABINET (REAR) ASSY (380) (S80)
2 2-591-956-01 RING (630), LENS (S90) 6 X-2055-119-1 CABINET REAR ASSY (630D) (S90: BLUE)
2 2-595-847-01 RING (620), LENS (S60/S80/ST80) 6 X-2055-116-1 CABINET, REAR, ASSY (620) (S60)
3 2-025-236-31 SCREW (M1.7 ) 6 X-2055-112-1 CABINET, REAR, ASSY (630C) (S90: SILVER)
4 1-479-108-11 CONTROL SWITCH BLOCK 7 3-078-890-11 SCREW, TAPPING
5 X-2055-114-1 CABINET (UPPER) ASSY (620) (S60/S80/ST80) 8 2-591-970-01 SCREW, TRIPOD
5 X-2055-110-1 CABINET (UPPER) ASSY (630C) (S90: SILVER) MIC901 1-542-618-11 MICROPHONE
DSC-S60/S80/S90/ST80
5-2
Downloaded from www.Manualslib.com manuals search engine
5. REPAIR PARTS LIST
CAUTION
SP901 Danger of explosion if battery is incorrectly replaced.
(Note 2) Replace only with the same or equivalent type.
MC-153
BT001 replace the same type
C003 58
^
S
T
60
-1
(Note 1)
22
55
56
LCD901
SW
-44
D002 6
57
64
54 63
65 (including CP401
(Note 2)
(CH-169 board) )
SY D901
-12
6
61
53 (Note 2)
51
MS 62
-271 Note 2: Speaker adhesive sheet cannot be recycle.
Exchange speaker adhesive sheet when you
remove the MC-153 flexible board (SP901)
from the main frame assembly.
54 A-1119-578-A SY-126 BOARD, COMPLETE (SERVICE) (GP4) 0 BT001 1-528-999-51 BATTERY, LITHIUM SECONDARY
54 A-1119-579-A SY-126 BOARD, COMPLETE (SERVICE) (GP5) 0 BT901 1-756-541-11 HOLDER, BATTERY (WITH TERMINAL)
0 55 A-1106-345-A ST-122 FLEXIBLE BOARD, COMPLETE 0 C003 1-112-186-11 CAP, ELECT 135uF 315V
0 56 1-478-349-11 FLASH UNIT D002 6-500-505-01 DIODE OPY5052
57 1-866-284-11 FP-200 FLEXIBLE BOARD D901 1-479-131-11 BLOCK, LIGHT GUIDE PLATE (2.0)
(S60/S80/ST80)
58 A-1106-342-A SW-446 BOARD, COMPLETE (TYPE C) (Note 1)
58 A-1106-349-A SW-446 BOARD, COMPLETE (TYPE S) (Note 1) D901 1-479-126-11 BLOCK, LIGHT GUIDE PLATE (2.5) (S90)
59 A-1106-346-A MC-153 FLEXIBLE BOARD, COMPLETE (Note 2) LCD901 1-805-787-31 INDICATOR MODULE, LIQUID CRYSTAL
60 2-025-236-31 SCREW (M1.7 ) (TYPE C) (Note 1) (S60/S80/ST80)
61 X-2055-117-1 MAIN FRAME ASSY (620) (Note 2) LCD901 1-805-785-31 INDICATOR MODULE, LIQUID CRYSTAL
(S60/S80/ST80) (TYPE C) (Note 1) (S90)
LCD901 1-805-798-31 DISPLAY PANEL, LIQUID CRYSTALAL (TYPE S)
61X-2055-113-1 MAIN FRAME, ASSY (630C) (Note 2) (Note 1) (S90)
(S90: SILVER) SP901 1-825-665-11 SPEAKER (1.3CM) (Note 2)
61 X-2055-121-1 MAIN FRAME, ASSY (630D) (Note 2)
DSC-S60/S80/S90/ST80 (S90: BLUE)
5-3
Downloaded from www.Manualslib.com manuals search engine
5. REPAIR PARTS LIST
110
111 112
109 CD
-57
3
113
IC001
101 (Note 2, 3)
107 108
106
104
(Note 1) 105
103
(Note 1)
114
(Note 1)
102
(Note 1)
Ref. No. Part No. Description Ref. No. Part No. Description
101 1-788-215-11 LENS, VIDEO (ED02E) 109 3-078-890-11 SCREW, TAPPING
102 2-591-682-01 PLATE (A), ORNAMENTAL FIXED (Note 1) 110 1-866-285-11 FP-201 FLEXIBLE BOARD
103 3-709-676-01 MATERIAL, FIXED PLATE ADHESION (Note 1) 111 A-1106-343-A CD-573 BOARD, COMPLETE
104 3-709-677-01 BARRIER UNIT (Note 1) 112 3-080-204-21 SCREW, TAPPING, P2
105 3-076-569-01 PLATE, LIGHT INTERCEPTION 113 2-591-987-01 SHEET, LENS INSULATING
106 1-788-103-11 OPTICAL FILTER BLOCK 114 3-709-678-01 TITE (B TITE M1.4X4.5), TAP
107 3-075-085-01 RUBBER (DQ), SEAL IC001 A-7112-263-A CCD BLOCK ASSY (CCD IMAGER) (Note 2, 3)
108 2-591-986-11 FRAME, LENS
DSC-S60/S80/S90/ST80
5-4
Downloaded from www.Manualslib.com manuals search engine
CD-573
< IC >
DSC-S60/S80/S90/ST80
5-5
Downloaded from www.Manualslib.com manuals search engine
MC-153 MS-271 ST-122 SW-446 (TYPE C)
Ref. No. Part No. Description Ref. No. Part No. Description
A-1106-346-A MC-153 FLEXIBLE BOARD, COMPLETE 0 A-1106-345-A ST-122 FLEXIBLE BOARD, COMPLETE
******************************* *******************************
(This flexible complete board is including
CN002 (multi connector).) 0 1-478-349-11 FLASH UNIT
< BATTERY > C001 1-100-611-91 CERAMIC CHIP 22uF 20% 6.3V
C002 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
0 BT001 1-528-999-51 BATTERY, LITHIUM SECONDARY 0 C003 1-112-186-11 CAP, ELECT 135uF 315V
0 C004 1-100-758-11 CERAMIC CHIP 0.047uF 10% 250V
< CONNECTOR > C006 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
S001 1-786-157-11 SWITCH, TACTILE (F (SELF TIMER)) R045 1-208-911-11 METAL CHIP 10K 0.5% 1/16W
S002 1-786-157-11 SWITCH, TACTILE (f (FLASH)) R046 1-218-989-11 RES-CHIP 1M 5% 1/16W
S003 1-786-157-11 SWITCH, TACTILE (a (SET)) R047 1-216-864-11 SHORT CHIP 0
S004 1-786-157-11 SWITCH, TACTILE (G (MACRO))
S005 1-786-157-11 SWITCH, TACTILE (g (REVIEW) < COMPOSITION CIRCUIT BLOCK >
S006 1-786-157-11 SWITCH, TACTILE (DISPLAY / LCD ON/OFF) RB001 1-234-376-21 RES, NETWORK 2.2K (1005 x4)
S007 1-786-157-11 SWITCH, TACTILE (MENU) RB002 1-234-376-21 RES, NETWORK 2.2K (1005 x4)
S008 1-786-157-11 SWITCH, TACTILE (T (ZOOM))
S010 1-786-157-11 SWITCH, TACTILE (IMAGE SIZE/DELETE) < SWITCH >
S011 1-786-157-11 SWITCH, TACTILE (W (ZOOM))
S001 1-786-157-11 SWITCH, TACTILE (F (SELF TIMER))
S002 1-786-157-11 SWITCH, TACTILE (f (FLASH))
S003 1-786-157-11 SWITCH, TACTILE (a (SET))
A-1106-349-A SW-446 BOARD, COMPLETE (TYPE S) (Note) S004 1-786-157-11 SWITCH, TACTILE (G (MACRO))
*********************** S005 1-786-157-11 SWITCH, TACTILE (g (REVIEW)
< CAPACITOR > S006 1-786-157-11 SWITCH, TACTILE (DISPLAY / LCD ON/OFF)
S007 1-786-157-11 SWITCH, TACTILE (MENU)
C001 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3V S008 1-786-157-11 SWITCH, TACTILE (T (ZOOM))
C002 1-112-021-91 CAP, CERAMIC 2.2MF F (1608) S010 1-786-157-11 SWITCH, TACTILE (IMAGE SIZE/DELETE)
C003 1-112-021-91 CAP, CERAMIC 2.2MF F (1608) S011 1-786-157-11 SWITCH, TACTILE (W (ZOOM))
R6 (size AA) alkaline USB, AV cable for Power cord (1) HR6 (size AA) Nickel-Metal
batteries (2) multi-use terminal (1) 0 1-776-985-11 (KR) Hydride batteries (2)
(not supplied) 1-830-345-11 0 1-782-476-13 (CH) (not supplied)
0 1-783-374-12 (UK, HK)
0 1-783-952-21 (AR)
0 1-790-107-22 (US, CND)
0 1-790-732-71 (JE)
DSC-ST80 only 0 1-823-946-12 (AEP, E)
0 1-827-945-12 (AUS)
Other accessories
2-590-046-11 MANUAL, INSTRUCTION (CSS-SA)
(ENGLISH, FRENCH) (AEP, UK, E, HK)
2-590-046-21 MANUAL, INSTRUCTION (CSS-SA)
(GERMAN, ITALIAN, DUTCH, SPANISH,
PORTUGUESE, SWEDISH, DANISH,
FINNISH, RUSSIAN) (AEP, E)
2-590-046-31 MANUAL, INSTRUCTION (CSS-SA)
(TRADITIONAL CHINESE, SIMPLIFIED
CHINESE, KOREAN, ARABIC) (E, HK)
Other accessories
2-590-636-11 INSTRUCTION (READ THIS FIRST) (ENGLISH) (US, CND, AEP, UK, E, HK, AUS, JE)
2-590-636-21 INSTRUCTION (READ THIS FIRST) (FRENCH, ITALIAN) (CND, AEP)
2-590-636-31 INSTRUCTION (READ THIS FIRST) (SPANISH, PORTUGUESE) (AEP, E, AR, JE)
2-590-636-41 INSTRUCTION (READ THIS FIRST) (GERMAN, DUTCH) (AEP)
2-590-636-51 INSTRUCTION (READ THIS FIRST) (TRADITIONAL CHINESE, SIMPLIFIED CHINESE) (E, HK, CH, JE)
2-590-639-11 INSTRUCTION (USER’S GUIDE) (ENGLISH) (US, CND, AEP, UK, E, HK, AUS, JE)
2-590-639-21 INSTRUCTION (USER’S GUIDE) (FRENCH, ITALIAN) (CND, AEP)
2-590-639-31 INSTRUCTION (USER’S GUIDE) (SPANISH, PORTUGUESE) (AEP, E, AR, JE)
2-590-639-41 INSTRUCTION (USER’S GUIDE) (GERMAN, DUTCH) (AEP)
2-590-639-51 INSTRUCTION (USER’S GUIDE) (TRADITIONAL CHINESE, SIMPLIFIED CHINESE) (E, HK, CH, JE)
DSC-S60/S80/S90/ST80
5-13E
Downloaded from www.Manualslib.com manuals search engine
[Description of main button functions on toolbar of the Adobe Acrobat Reader Ver5.0 (for Windows)]
Toolbar
Finding a text
1. Click the Find button . Moving with link
2. Enter a character string to be found into a text box, and click
the [Find]. (Specify the find options as necessary) 1. Select either palm tool , zoom tool , text selection tool
, or graphic selection tool .
Application to the Service Manual: 2. Place the pointer in the position in a text where the link exists
To execute “find” from current page toward the previous pages, (such as a button on cover and the table of contents page, or
select the check box “Find Backward” and then click the blue characters on the removal flowchart page or drawing
“Find”. page), and the pointer will change to the forefinger form .
3. Then, click the link. (You will go to the link destination.)
Switching a page
• To move to the first page, click the .
• To move to the last page, click the . “Rotate”
• To move to the previous page, click the . • Click rotate tool , and the page then rotates 90 degrees each.
Revision History
S.M. Rev.
Ver. Date History Contents
issued
1.0 2005.03 Official Release — —
DSC-S60/S80/S90/ST80